REPAIR / REPLACEMENT AND MAINTENANCE OF STREET LIGHTS, TIMER PANELS, TREE TRIMMING, RESTRINGING OF OVERHEAD LINES AND CONNECTED WORKS AT VARIOUS LOCATIONS AT ZONE 1A, 1B AND ZONE 1C UNDER AGE E/M NO 1 OF GE (U) SECUNDERABAD

Amount

Taking down street light fittings of any watt ( tube light / HPSV fittings) from existing position on pole/ wall/ tower complete all as specified and as directed by Engineer-in-charge.

Taking down old unserviceable post top lantern/bollard / Garden/ Gate light fitting of any watt and type from existing position complete for repair and replacement all as specified and as directed by Engineer-in-charge.

Supply and fixing post top lantern LED type 25/30/35 watt 230 volts AC outdoor type with decorative post top for 360 degree indirect light IP 65 protection with impact and corrosion resistant complete with driver and lamp complete. complete all as specified and directed by Engineer -in-charge.

Supply fixing connecting and testing decorative LED Bollard light with opal diffuser & aluminium reflector of 8/9/11watt 3 Feet LED including nut, bolts, washers, clamps etc complete all as specified and directed by Engineer -in-charge

Supply & fix 70 watts LED Street light fitings new generation energy saving ,environmental friendly ,long life,versatile pressure die cast aluminium IP65 with 10KV nominal voltage surge protection ,luminaire with high power LED as light source and suitable drivers etc complete all as specified and directed

Supply & fix 90 watts LED street light fitings new generation energy saving ,environmental friendly, long life,versatile pressure die cast aluminium IP65 with 10KV nominal voltage surge protection ,luminaire with high power LED as light source with suitable drivers etc complete all as specified and directed

Supply & fix 110 watts LED street light fitings new generation energy saving ,environmental friendly ,long life,versatile pressure die cast aluminium IP65 with 10KV nominal voltage surge protection ,luminaire with high power LED as light source and suitable drivers etc complete all as specified and directed

Supply & fix 120 watts LED Street light fitings new generation energy saving ,environmental friendly ,long life,versatile pressure die cast aluminium IP65 with 10KV nominal voltage surge protection ,luminaire with high power LED as light source and suitable drivers etc complete all as specified and directed

Supply & fix 200 watts LED street light fitings new generation energy saving ,environmental friendly ,long life,versatile pressure die cast aluminium IP65 with 10KV nominal voltage surge protection ,luminaire with high power LED as light source and suitable drivers etc complete all as specified and directed

Supply & fix 70 watts LED flood light fitings new generation energy saving, environmental friendly, long life,versatile pressure die cast aluminium IP65 with 10KV nominal voltage surge protection, luminaire with high power LED as light source and suitable drivers etc complete all as specified and directed

Supply & fix 120 watts LED flood light fitings new generation energy saving ,environmental friendly ,long life,versatile pressure die cast aluminium IP65 with 10KV nominal voltage surge protection ,luminaire with high power LED as light source and suitable drivers etc complete all as specified and directed

Supply & fix 150 watts LED flood light fitings new generation energy saving ,environmental friendly ,long life,versatile pressure die cast aluminium IP65 with 10KV nominal voltage surge protection ,luminaire with high power LED as light source with suitable drivers etc complete all as specified and directed

Supply & fix 200 watts LED flood light fitings new generation energy saving ,environmental friendly ,long life,versatile pressure die cast aluminium IP65 with 10KV nominal voltage surge protection ,luminaire with high power LED as light source with suitable drivers etc complete all as specified and directed

Fabrication and installation of GI pipe bracket made of medium Grade tubing of size 40 mm dia, duly bended by hot forgoing after filling of sand, length 1.50 mtr including providing two pair of MS flat strip clamps 40 mm x 4 mm with GI bolts nuts and washer including taking down old unserviceable complete all as specified and directed

S&F hot press moulded SMC junction / terminal box of size with internal diamensions of 200 x 140 x 95 mm with hinged door, incl provision of 2 way connector 415 Volts made out of polycarbonate or bakelite and 1 No MCB of 6 Amps with DIN bar, drilling holes for cable connections, connecting incoming and or out going cables by providing suitable of size of cable lugs/glands, fixied on pole by means of clamps made out of MS flat iron of size 25 mm x 3 mm including dismantling of old unserviceable all as specified and as directed.

Excavation in trenches not exc 1.5 mtr wide and not exc 1.5 mtr in depth; for trench of cable etc and getting out in hard soil complete all as specified and as directed.

Excavating in Trenches, not exc. 1.50 mtr wide and exc. 1.50 mtr but not exc. 3.00 mtr in depth, for Foundation of Poles, etc. and getting out in Soft/ Loose Soil, complete all as specified and as directed.

Returning, filling in, including spreading, leveling, watering and well ramming in layers not exc 25 cm in Soft/loose soil complete all as specified and as directed

Removing excavated material to a distance n.exc 50 mtr and depositing where directed at level n.exc 1.5 mtr above the starting point all as specified and as directed

Material and labour for sand cushioning for protection of underground cable consolidated and compacted with clean dry sand all as specified and as directed (Compacted thickness shall only be measured and paid)

Supplying and laying un-reinforced precast concrete cable cover, class Class LV, Type I, flat, size 250mm x 150mm x 40mm

Supply and Lay bricks common burnt clay building bricks sub-class "B" designation 75 of size 230x115x75 mm

Material and labour in replacement of old unserviceable XLPE insulated GI wire/strip armoured electric power cable (Heavy duty) ISI marked with stranded aluminium conductor 1100 volts grade, cross sectional area 6 Sqmm 2 core laid in trench /poles/on wall all as specified and as directed

Material and labour in replacement of old unserviceable XLPE insulated GI wire/strip armoured electric power cable (Heavy duty) ISI marked with stranded aluminium conductor 1100 volts grade, cross sectional area 10 Sqmm 4 core laid in trench /poles/on wall all as specified and as directed

Material and labour in replacement of old unserviceable XLPE insulated GI wire/strip armoured electric power cable (Heavy duty) ISI marked with stranded aluminium conductor 1100 volts grade, cross sectional area 16 Sqmm 4 core laid in trench /poles/on wall all as specified and as directed

Material and labour in replacement of old unserviceable XLPE insulated GI wire/strip armoured electric power cable (Heavy duty) ISI marked with stranded aluminium conductor 1100 volts grade, cross sectional area 25 Sqmm 4 core laid in trench /poles/on wall all as specified and as directed

Trimming/pruning and removing of tree branches or any other foreign objects from HT/LT over head conductor and clearing the OH Line of any type and size for one span of any length in 2 way /4 way/6 way conductor system. Notes: The contractor is responsible for provision of necessary T & P and safety equipments to complete the job.

M & L for painting the existing LT steel poles of 9.0 Mtr long including cross arms, clamps, street light junction boxes etc with 2 coats of aluminium paint over a coat of red oxide primer including throughly cleaning the existing surface, painting the poles up to 1.5 Mtr height with alternate bands 30 cm height (3 Nos black and 2 Nos Yellow) from ground level, complete all as specified and directed.

M & L for Painting the existing LT PCC poles with applying two coat of cement based paint over one coat of primer including painting of cross arms, clamps, etc with two coats of aluminum paint and providing alternative band of 30 cm width (3 Nos black and 2 Nos yellow) from bottom of pole to 1.5 meter height complete all as specified and directed.

Labour only for releasing the binding of ACSR conductor of LT / HT over head line from insulator, removing the jumper, connector, service wire, UG cable and restringing the existing ACSR conductor of any size, length, span upto desired sag and fixing the existing ACSR conductor on insulators by proper binding, jumper connection etc complete all as specified and directed. Notes:- (i) Single run of conductor will be measured as one unit which is deemed to be included in the quoted unit rate. (ii) Extra aluminum conductor required for jumpers and binding purpose is deemed to be included in the quoted unit rate.

Supply and fix Solar LED street light of 20 watt capacity with in built solar panel on the top of the light, inbuilt incl battery complete all as directed.

M&L cross arm bracing supports, clamp and back plate from structural steel section including nuts & bolts washer, welding, bending, cold or hot drilling holes for bolts in any shape or size as indicated or as directed and including of one coat primer, one under coat and one finishing coat of aluminium paint for making clamp to be used for fixing of flood light /street light on pole including taking down old unserviceable.

Supply & Erecting Steel Tubular Swaged Pole Type 410-SP-31 (9.0 METRE long) including Cast Iron Base Plate, Finial Taper Plug, Cap, Mild Steel Bolts, Nuts, Screws including applying Two Coats of Black Bituminous Paint Internally and Externally upto Planting Depth and applying with Two Coats of Aluminium Painting over a Coat of Aluminium Primer (Externally from Top of Coping) including dismantling old unserviceable complete all as specified and as directed.

Supply and fixing lantern of dia 60 CM for fixing of flood light, cap type to be fixed on the top of 9 m SP-31 Steel pole , made of MS pipe medium grade dia greater than the top dia of the pole of length 0.35 M supported by MS flat iron of size 50X6 mm 8 nos including two coat of aluminium painting over a coat of redoxide primer including taking down old unserviceable complete all as directed

S&F in repairs surge protection of 10 KV suitable upto 100W LED light fittings suitable to operate on input voltage 440 AC, 50 Hz, complete all as specified and directed.

S&F in repairs Electronic drivers suitable for 60/72 W LED fittings suitable to operate on input voltage of AC 100-265 V, 50 Hz including taking down and refixing after repairs complete all as specified and directed.

S&F in repairs Electronic drivers suitable for 90 W LED fittings suitable to operate on input voltage of AC 100-265 V, 50 Hz including taking down and refixing after repairs complete all as specified and directed.

Supply and lay PVC Insulated , PVC sheathed industrial HV round multicore flexible cable with copper conductor 3 core 1.5 sqmm including PVC conduit 20 mm dia medium grade and necessary bends, fittings and fixtures as required for connection of light fittings in replacement of old unserviceable .

M&L for PCC 1:3:6 type C2 using 40mm graded aggregates as in foundation, filling and mass concrete for pole / stay / post including necessary form work complete all as specified and directed.

M&L for PCC 1:2:4 type B1 using 20mm graded stone aggregate in coping of poles / foundation for poles, struts, posts etc including necessary form work, finished the exposed surfaces fair and even without using extra cement complete all as specified and directed.

Supply and replace GI pipe fixed on the top of gate piller by 50 mm dia medium grade GI pipe of length 30 cm( 20 CM inside the piller and 10cm above the piller including necessary cement work and making hole on GI pipe if required complete all as directed. Note: Quoted rate is deemed to be inclusive of making good of disturbed suface including necessary painting to match with the adjoining surface.

M & L in replacement of old unserviceable earthing complete with galvanised steel earth plate electrode 60cm x 60cm x 6mm thick buried directly in ground earth pit not less than 2.25 mtr deep below normal ground level) with top edge of plate not less than 1.5m below ground level, connecting to the Galvanised iron earth strip 32 x 6mm dia, by means of nuts, bolts, check nuts and washer etc of galvanised iron and earth lead protected by provision of GI pipe medium grade 40mm bore from earth elelctrode to test point incl provn of concrete pit in PCC (1:2:4) type B-1 using 20mm graded stone agagregates with 40mm thick cover of RCC (1:2:4) reinforced with XPM sheet (weight not less than 4Kg/Sqm) and frame of angle iron 25 x 25 x 6mm with lugs 2 Nos and with 8mm dia MS bar handle made to shape, GI pipe medium grade 20mm bore pipe for watering perforated at bottom 1.75 mtr long placed on top edge of earth plate, common salt and charcoal filling test point with fixing arrangement, funnel, wire mesh and earth work in hard/dense soil, returning in and removal of surplus soil to a distance not exceeding 50mtr, complete all as specified in electrical plate No 3 of SSR Part I and connection to earth test point including testing on completion all as directed. Note :- Item of earthing deemed to be included cost of 7.5m long galvanised iron earth strip of 32 x 6mm size and protection pipe of 40mm bore GI medium grade.

Material and labour in replacement of old unserviceable for galvanized iron tubing 50 mm bore light grade with all fitting for hanging of ceiling fan / protection of cable /for fixing of garden light incl necessary clamp, bolt/nut if any and making hole on wall complete all as specified and as directed.

M&L for twin core 1100 volt grade aluminium service wire cross sectional area 4.0 Sqmm for connection of light complete all as specified and directed

M&L for twin core 1100 volt grade aluminium service wire cross sectional area 6.0 Sqmm for connection of light complete all as specified and directed

M&L for twin core 1100 volt grade aluminium service wire cross sectional area 10.0 Sqmm for connection of light complete all as specified and directed

Cutting the existing road straight by manual, depth and width not less than 1 mtr below ground level for passing of underground cable and filling back with excavated soil upto 75% road portion and 25% shall be made with cement concrete 1:2:4 (using 20 mm graded aggregate stone complete all as specified and directed.

Supply and lay PVC Insulated , PVC sheathed industrial HV round multicore flexible cable with copper conductor 3 core 2.5 sqmm including PVC conduit 20 mm dia medium grade and necessary bends, fittings and fixtures as required for connection of light fittings . Note : Used for garden light connection, excavation, retuning filling etc will be measured and paid separately.

Dismantling LT steel tubular pole of any height by taking out from PCC foundation complete and shifting to other location as directed including fixing the pole in true vertical position including excavation and earth work, PCC 1:4:8 type D2 (using 40mm graded stone aggregate) as base concrete and PCC 1:3:6 type C2 (using 20mm graded stone aggregate) in both foundation and coping of poles all as specified in SSR Part I-2009 and applying two coats of aluminium paint to pole surface complete all as directed by Engineer-in-Charge.

M&L for Making hole 2 nos (one hole near JB another hole near bottom portion of bracket) on existing steel tubuler pole (SP -31) of suitable size for passing of Street light connection HV Round cable 3 core 1.5 / 2.5 Sqmm from Junction Box to street light complete all as directed

Demolition of coping of pole as required for placing of cable protection pipe and making good the same by using PCC and rendering complete al as speccified and directed. Note: Quoted rates deemed to be inclusive of PCC and rendering.

SUN LIGHT HOUSE

LEO ENTERPRISES

L and S ENTERPRISES

Sri Balaji Enterprises

sree venkateswara enterprises