SMART COMPREHENSIVE REPAIR TO GE OFFICE, BSO OFFICE, MES QTS, BSO YARD, STORAGE ACCN AND ANCILLARIES ALONG WITH CERTAIN REPAIRS IN THE AREA OF AGE B/R-II UNDER GE (N) AHILYANAGAR

Amount

Dismantling, floor, hearth or wall tiling including cement mortar bedding/ backing and removing all rubbish/ dismantled material outside MD Land.

Demolition of plain cement concrete (unreinforced) in ground floor not exceeding 15 cm thick all as directed.

M&L for 75 mm thick plain cement concrete 1:4:8 type D2, using 40 mm graded stone aggregate as in sub base all as directed.

M&L for plain Cement concrete (1:4:8) type D-2 using 40mm graded stone aggregate as in foundation filling and mass concrete etc complete all as specified and directed by Engineer-in-Charge

M&L for Glazed colour ceramic tiles 450X 300X 7mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match coloured as approved by GE as in dado / skirting or on vertical surfaces, over and including 10 mm thick backing coat in CM (1:4) set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tile etc complete all as specified and directed.

M&L for joint free / rectified anti skid ceramic coloured tiles 7-8mm thick matching to dado tiles area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, (400x400)mm as in floor etc laid over and including screed bed 15 mm thick in cement mortar 1:6 set and jointed with white or coloured cement to match complete all as specified and as directed.

M&L for joint free / rectified vitrified/ ceramic light shade coloured tiles 8-10 mm thick as approved by GE (square /rectangular) area of each tile not exceeding 0.36 sqm,(600 x600)mm as in floor etc laid over and including screed bed 15 mm thick in cement and sand mortar (1:6 ) set and jointed with white or coloured cement to match the shade of tile etc complete all as specified and as directed

-Ditto- as per ser item No 07 above but on skirting and backing coat of 10 mm thick in CM 1:4

Dismantling of stone slabs and tiles of any description or thickness in floors, approns etc laid and bedded in any mortor and removing all rubbish/dismantled material outside MD Land all as directed.

M & L for Providing and laying 60mm thick factory made chamfered edge cement concrete paver block of M-35 grade with approved colour, design & pattern as in footparth, parks, lawns, drive ways or light traffic parking etc., of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of fine sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand; complete all as specified and directed by Engineer-in-Charge

M&L for 20mm thick pre-polished granite stone slab of approved shade and colour Jet Black / Telephone Black as in top table, top of WHB, kitchen slab/platform, steps, gate pillars, cills, jambs, lintel etc or on vertical surfaces including vertical projection, full round moulding the edge laid over screed bed 15mm thick in CM 1:4 jointing , pointing in white cement 1:2 using marble dust with admixture of pigment to match the shade of granite and rubbing polish to achieve mirror finish complete all as specified and directed.

M&L for machine cut cudappah stone slab 20-25 mm thick over cement screed base, laid over and including 15 mm thick screed bed in cement mortar 1:6, set and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing all as directed.

M&L for 30 mm thick Rough dressed(shahabad) lime stone slab flooring, laid dry, jointed and pointed in cement mortar 1:3 as in floor/plinth etc over bedded and jointed in cement mortar 1:6 and pointed in cement mortar 1:3 in floor/plinth etc over and incl 15 mm thick screed bed in CM 1:6 complete all as specified and directed

Fixing only 30-40mm thick rough dressed Shahabad stone as in floor/plinth etc over and incl 15mm thick screed bed in CM 1:6 including dismantling complete all as specified and directed

M&L for heavy duty vitrified paver tiles 30cm x 30cm x 10mm thick,approved by GE withnset,jointed and pointed in neat cement slurry with grey cement and pigment to match in floors,over and including screed bed or bedding a layer of 15 mm in cement mortar 1:6 complete all as specified and directed by Engg-in-charge.

Demolition of plain cement concrete solid block masonary built in cement mortar & removing all rubbish/dismantled material outside MD Land.all as directed.

M&L forBrickwork with fly ash bricks, straight or curved on plan exc 6m mean radius, built in cement mortar 1:6 complete all as specified and directed by Engineer-in-Charge

Taking down cement plaster on brick / stone walls including raking out joints, hacking for key, scrubbing down with water all as directed

M&L for rendering, 12 mm thick on stone surfaces in cement mortar 1:6 surfaces finished even and fair finish all as specified and directed.

M&L for rendering, 10 mm thick on brick/concrete surfaces in cement mortar 1:6 surfaces finished even and fair finish all as specified and directed.

M&L for rendering, 15 mm thick on stone/brick/ concrete surfaces in cement mortar 1:4 surfaces finished even and fair finish all as specified and directed.

M&L for 2 mm wall care putty on walls complete all as specified and directed by Engg-in-charge.

Dismantling of single layer manglore pattern in roofing & removing all rubbish/dismantled material outside MD Land.all as directed.

-ditto- all as per ser item no 23 above but bedded in cement morter

M&L for roofing tile, manglore pattern interlocking at sides joints laid dry

-ditto- all as per ser item no 26 but except manlore pattern tiles

M&L Ridge or hip tiles to suit mangalore pattern of roofing tiles, bedded and jointed in cement morter 1:6

Dismantling timber scantling 40 sqcm and over in section, in any postion framed work as in scanging of main joist of roof & removing all rubbish/dismantled material outside MD Land.

-ditto- all as per ser item no 28 above but in fillets,rails, posts, rafters purlins etc under 40 sqcm in section framed work & removing all rubbish/dismantled material outside MD Land.

Dismantling battens for tiles, shingles etc of any size including tilting fillets spacing exc 15 cm &removing all rubbish/dismantled material outside MD Land.

Dismantling of plain or corrugated steel sheeting, any gauge, thickness, including ridge & removing all rubbish/dismantled material outside MD Land.all as directed.

M&L for second class hard wood in scantling of roof rafters, etc wrougt framed

S&F Pre-painted Galvalume sheet shall be 0.50mm thick (total coated thickness), 550 Mpa minimum, yield strength. It shall be coated with hot dip alloy of 55% Aluminium 43.5% Zinc 1.5% Silicon and finished with resin coat on both surfaces @ 150 gm/sqm of coating (total both surfaces) having overall width and laid width as specified and shall be fixed using hot dip galvanized, self drilling and self tapping screws neoprene and EPDM washers. Penetrations and laps in sheet shall be sealed by using proper sealant profile. HDPE fillers shall be provided wherever required to close voids between sheets, sheet & fasteners etc.complete all as specified and directed by Engg-In-charge.

Supply and fix 0.50 mm thick plain, galvanised, mild steel sheeting, in ridges, hips, valley gutters, drip and straight flashings (length and girth as fixed) with, 550 Mpa minimum, yield strength. It shall be coated with hot dip alloy of 55% Aluminium 43.5% Zinc 1.5% Silicon and finished with resin coat on both surfaces @ 150 gm/sqm of coating (total both surfaces) having overall width and laid width as specified and shall be fixed using hot dip galvanized, self drilling and self tapping screws neoprene and EPDM washers. Penetrations and laps in sheet shall be sealed by using proper sealant profile. HDPE fillers shall be provided wherever required to close voids between sheets, sheet & fasteners etc.complete all as specified and directed by Engg-In-charge.

Dismantling wrought iron or mild steel work of any description not otherwise provided for

S&F of steel work in post,joist,channel,angle, or tee section fixed independently,without connecting plates etc as per Fe 410-W (Grade-E-250 quality-A)

Supply and fixing in repairs vitreous china wash down water closet (Pedestal pattern) white including fixing bolts with and including plastic water closet seat cover closed pattern with flat bottom and cover and MSCP almn hinges device complete connecting to 'P' or 'S' trap all as directed.

Supply and fix in repairs vitreous China white squatting pan, Orissa pattern of size 580 X 440 mm width with integral foot rest set in cement concrete including flush pipe and connecting to trap / flushing cistren complete all as specified and directed.

Supply and fix in repairs wash hand basin vitreous China, flat back of size 550 X 400 mm including a pair of brackets, PTMT waste coupling, 32 mm dia PVC flexible waste pipe and connecting to stop valve and nahani trap all as directed.

S&F in repair for Vitreous China bowl urinal flat back size of 465x355x265mm white (minimum) with grating and union for discharge pipe (excluding flushing cistern flush pipe ad waste pipe)

M&L for preparation of new unplastered or plastered surfaces and applying two coats of oil bound distemper including chalk whitening on wall including smooth roller finish complete all as directed.

M&L for preparation of newly plastered surface of wall and apply two coats of cement based paint over a coat of alkali primer any height including scaffholding etc complete all as directed.

Taking down chowkats or frames exc 1.5 Sq m but nexc 4.00 sqm with shutters (without taking off shutters from the frames) all as directed.

Taking down chowkats or frames n exc 1.5 Sq m with shutters (without taking off shutters from the frames) all as directed.

Taking down shutters of any description exc 1 sqm and n exc 2 sqm each all as specified directed by Engineer-in-charge.

Taking down shutters of any description n exc 1 sqm each all as specified directed by Engineer-in-charge.

S & F Pressed steel door frame of size 125 x 60mm for doors with one or more rebates including necessary fixing lugs, hings, lock strike plate, etc, complete all as specified,

S&F Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other Frames/ Chowkhat of size 45 x 85 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2 , modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/lugs/SS dash fasteners of required dia and length complete as per direction ofEngineer-in-Charge. (M.S. hold fast/ lugs or SS dash fasteners shall be paid for separately).

Factory made single extruded WPC (Wood Polymer Composite) solid plain flush door shutter of 30mm size comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2 , modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer-In-Charge. (Note: stainless steel butt hinges and necessary S S screws shall be paid separately)

Supply and fixing 30 mm thick Flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides

Supply and fix 35 mm thick glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc. (without sash bars), edges of framing plain, chamfered or rounded. fitted with cut and mitred beads for securing glass, etc.; sizes of me-mbers of shutters as specified in SSR Part I, Section 8, clause 8.24 (a) all as directed.

Supply and fix solid PVC door frame of size 50 mm X 47 mm made out of 5 mm plain colour PVC sheet reinforced with MS square tube, all as directed.

Supply and fixing Factory Made Solid PVC Moulded Door Shutter, with wood free EPS, 28 to 30mm thick (stiles), with 2, 4, or 6 raised panel design with 2mm thick Moulded PVC Sheet on the front face & 2mm thick 3D wood grain Moulded PVC Sheet Polyurethane painted on the front face & 2mm Plain colour PVC Sheet on back face

Supply and fix galvanised mild steel wire cloth 0.56 nominal dia of wire and average width of aperture 1.18 mm and fixed with tinned tacks or galvanised wire staples all as directed.

Supply and fix mild steel butt hinges medium weight cold rolled of size 100mm

Supply and fix aluminium alloy, anodised, sliding door bolt with hasp and staple (bolt type) and fixing clips of sheet, cast or extruded section and fixing bolts and sliding bolts of extruded section of cast aluminium alloy and fixed 300mm long.

Supply and fix aluminium anodised barrel tower bolt of extruded section 200mm long.

Supply and fix aluminium anodised handles of extruded section 150mm long.

S&F in repair 300mm mild steel ordinary rat tail rod patteren door spring including roller and roller plate complete all as specified and directed

S&F in repair aluminium extruded section body door closer for aluminium door shutter hydraulically regulated, designation No 1 universal type, suitable for door shutter upto 700 mm in width and of weight not more than 35 kg and fixed.complete all as specified and directed.

S&F in repair 150mm Floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed in floor complete all as specified and directed.

S&F in repair Cylindrical Latch Door Lock Tubular (Dumbell lock) stainless steel finish fixed in door complete all as specified and directed by Engg-in-charge. Make:Godrej, Europhia and equivalent.

M&L for two coats of synthetic enamel paint over a coat of pink primer for new wooden surfaces of any description exc 10 cm width or girth including preparation of surfaces and smooth finish with roller all as directed.

M&L for two coats of synthetic enamel paint over a coat of red oxide primer for new steel surfaces of any description exc 10 cm width or girth including preparation of surfaces all as directed.

Supply and fix mild Steel 20 mm dia decorative powder coated curtain rods with fixing brackets fixed in repairscomplete all as specified and directed.

Supply and fixed in repairs 32 mm dia PVC waste pipe(outlet pipe) plain fixed to waste coupling of WHB or Sink etc all as directed.

Supply and fixe in repairs stainless steel kitchen sink matt finish with draining over all size 950 X 510 mm and bowl size 410 X 410 X 230 mm, made out of 1.00 mm thick SS sheet of high quality including a pait of brackets, waste coupling, plug and chain, 32 mm dia PVC flexible waste pipe and nahani trap complete all as specified and directed.

S&F in repair wall mixture, with provn for overhead shower all as specified and directed by Engg-In-Charge

Cleaning the surface with wire brush,detecting sources of lea and removing/taking down unsound treatment/ surface, proving material and labour for carrying out non-destructive water proofing treatment to sunken portion of slab,floor and walls of bath, WC, WHB and floor trap (combined unit) by using construction chemical method as hydrophobic PU grouting etc with first course of injection MDI based PU foam and second course of injection PU plain all as manufacturers instruction,etc,the PU foam shall have 100% solids and solvent free,and shall expand 30-40 times its volume at liquid stage in presence of water,the PU plain injection shall have minimum 100CPS visscosity and shore hardness minimum 50 complete all as specified and directed.Make:PIDILITE or equivalent

M&L for fixing the metallic packer for hydrophobic PU foam including making holes and sealer all as per manufacturers specification,the PU foam shall have 100 % solids and solvent free,and shall expand 30-40 times its volume at liquid stage in presence of water,the PU plain injection shall have minimum 100CPS visscosity and shore hardness minimum 50 complete all as specified and directed.Make:PIDILITE or equivalent. Note:This item is catered only for Material and labour by for fixing the metallic packer

M&L for the chemical cleaning of tile joints and re-grouting carefully by washing the existing tile with heavy duty tile cleaner preferably of M/S Pidilite or equivalent cleaner,again washing with fresh jet water, scratching the joints and filling the same with (white/matching colour) epoxy tile grout of M/S Pidilite, ROOF RTM epoxy or euivalent,curing,cleaning the surface etc as per the sample done at site complete all as specified and as directed.

M&L in repairs for false ceiling with vinyle faced Arm-GYP-FB, celing 600 x 600 x 7-8 mm thick with washable metallized polyster foil backing with vinyle covered edges supporting sections shall be of sutable size from same makes embossed on section and level adjuster duly suspended by 2mm dia GI wire fixed to roof at 600mm center to center as per manufacturere,s instruction and all as directed Make : Armstrong or equivalent in Saint Gobin/ Lafarge

Supply and fix in repair health faucet (hand shower) with 8 mm dia 1 m long flexible tube wall mounted / hooked all as per

Supply and fix in repair bib tap, 15 mm dia, CP cast copper alloy with crutch or butterfly handle screwed down for iron pipe or for brass ferrule all as directed.

Supply and fixing in repairs stop valve cast copper alloy, fancy type screwed down, high pressure with crutch or butterfly handle screwed both ends for iron pipe or for union and fix of size 15 mm bore

Supply and fix in repair 15 mm dia pillar tap, cast copper alloy, with capstan heads, chromium plated, fancy type, screwed down high pressure, with long screwed shanks and fly-nuts, screwed for iron pipe all as directed.

Supply and fix in repairs, shower rose with shower arm

Hacking out old broken glass (any thickness size,quality or description) from wooden frames or stone, concrete or brick surrounds glazed with putty or fixed with beads n'exc 1.5 Sqm.

M&L for glazing with 3 mm thick sheet glass ordinary quality and glazing with oil putty in square not exc 0.50 sqm in each pane all as directed.

Supply and fix in repair galvanised mild steel wire cloth 0.56 nominal dia of wire and average width of aperture 1.40 mm and fixed with tinned tacks or galvanised wire staples all as directed.

Supply and fix in repairs rotational moulded polyethylene water storage tanks Tripal layer (cylindrical vertical with closed top) of 1000 litres capacity hoisted and fixed in position including 20 mm dia ball valve, high pressure of PTMT with epoxy coated aluminium rod and high density plastic ball screwed to irin pipr and connecting complete all as specified and directed.

S&F in repairs PVC connections 15 mm size with Stainless steel Nuts of length 600mm

S&F in repair for stainless steel grating without waste holes 100 mm dia

S&F in repair for stainless steel grating with waste holes 100 mm dia

S&F for PVC (SWR) floor trap, plain with grating including jointing with solevent cement 75 mm bore

S&F in repair PVC (SWR) 110mm bore (dia) soil, waste and vent Pipe, (ISI Marked), in any length with rubber ring Joints fixed to wall with necessary stay clamps/ laid in trenches/ floor etc complete all as specifed and directed.

.-Ditto- all as per ser item no 86 above but as in trenches or floor

S&F in repair PVC (SWR) 75mm bore (dia) soil, waste and vent Pipe, (ISI Marked), in any length with rubber ring Joints fixed to wall with necessary stay clamps/ laid in trenches/floor etc complete all as specifed and directed.

.-Ditto- all as per ser item no 88 above but as in trenches or floor

S&F PVC (SWR) 110 mm bore (dia), Bends any type, etc. and Jointing with Solvent Cement, complete all as specified and as directed

S&F PVC (SWR) 75mm bore (dia), Bends any type, etc. and Jointing with Solvent Cement, complete all as specified and as directed

S&F PVC (SWR) junction single, (Single T) equal or un equal 110mm bore

S&F PVC (SWR) junction single, (Single T) equal or un equal 75mm bore

S&F PVC (SWR) junction single, (double Y) equal or un equal 110mm bore

S&F PVC (SWR) vent cowl110mm bore

S&F for low density polyethelene pipes 32 mm bore (LDPE) of pressure rating 6 Kg/cm² laid in trenches/fixed to wall

Supply and fix repairs 10 Ltr PVC valveless, syphonic action type, flushing cistern, low level, all accesories all as directed. Make :- Sleek essence series Of Hindware or Cat part No E8303 Of Parryware .

Taking up or down steel tubing and connections,15 mm bore

-ditto- all as per ser item no 98 above but 20mm bore

S&L of CPVC pipes SDR 11 including fittings in trenches, 16mm outer dia fixed to walls /ceiling or laid in trenches incl all necessary fittings.

-ditto- all as per ser item no 100 above but 20mm outer dia etc

Cutting chases, pinning in makding good to facing where required and pointing in cment morter 1:3 for consealed water tubing cutting not exc 10 cm girth

Supply and fix coloured anodised aluminium two/three track window made out of Jindal aluminium sections Nos 20671,20672,20690 & 20668 complete all as specified and directed by Engg-in-charge

S&F coloured anodised aluminium ventilator as per PS and make approved by GE including 5 mm thick plaint sheet glass and stainless steel wire guaze as per PS, locking arrangement all as directed.all fittings locking arragement, glazing, guazing and fixed with suitable size of screws all as directed

S&F in repair for 19/20mm PVC shutter Colour PVC prelaminated board fixed to timber frame worka as in cup boards shutters/shelves/pelmets box and similar items etc complte all as specified and directed by Engineer-in-Charge

S&F for in repaire Auto closing hinges 35mm of o crank (KH-001) ir 8 crank (KH=002) openable at 110 degree for kitchen cabinet shutters fixed complete as specified and directed

Supply and fix tubular towel rail, brass chromium plated 20 mm dia `D' type, 60 cm long between flanges including a pair of brackets etc complete all as specified and directed by Engineer-in-Charge

S&F in repairs PVC Seat Cover with hinges complete all as specified.

S&F Solid PVC Wall lining consisting of 5mm thick plain colour PVC sheet inclusive of solvent cement and fixing at site on PVC frame as per specification and drawing, inluding taking down/ out of existing wall panneling etc complete all as specified and directed by Engineer-in-Charge

Excavation over areas,n exc 1.5 m deep and getting out soft/loose soil complete all as specified and directed by Engg-in-cgarge.

Returning, filling in excavated material (soil) including spreading, levelling, watering and well ramming in layers not exc 25 cm in soft / loose soil etc complete all as specified and directed by Engineer-in-Charge

Removing excavated material exc.250m but n exc. 500m and deposited where directed.

Cutting out of shrubs, kerbs and small plants of stem n exc 30 cm girth measured 1 m above average ground level including cutting of grass and removing rubbish material like branches, leaves, grass and garbbage to clear the alignment of existing seage /drainage line to make site workable condition and making good the disturbed ground complete all as directed

M&L for 150mm bore Reinforced cement concrete pipe, type NP-2 laid in trenches and jointed as specified, making necessary connections after cutting into existing sewer line /manhole to make it functional after taking down/out salt glazed ware, AC or reinforced concrete pipe as existing at site complete all as specified and directed.

-ditto- all as per ser item no 114 (here-in-before) but 200mm bore RCC pipe

-ditto- all as per ser item no 114 above but 300mm dia RCC pipe

Supplying and fixing precast manhole cover (LD) of size 12" x 36" made up of steel fibre reinforced concrete M-30 grade as per IS etc complete all as specified and directed by Engineer-in-Charge Note : Make and material shall be as approved by GE.

-ditto- all as per ser item no 117 (here-in-before) but of size 12" x 48" etc.

Cleaning/ desludging of existing Manhole/septic tank of any capacity/sump well of any dia and depth incl taking out sludge in any form and other foreign matter etc viz sediment, sand, ash, grease, fibre, silt, roots or vegetation etc, cleaning the premises using chlorine powder etc complete all as specified and directed by Engineer-in-Charge.

M&L for providing water proofing treatment on roofs, as per manufacturere's instructions and as specified after taking down/out as existing out at site etc complete all as specified and directed by Engineer-in-Charge (a) Cleaning the newly plasterd surfaces with wire brushes and applying a bituminous primer @ 0.30 l/sqm & surface shall be allowed to dry. (b) Applying and laying torch APP polymer modifiedbituminous membrance 3mm thick with non woven polyster matt as reinforced weighing not less than 3 kg/sqmts by therofusion process as per manufacturers specification including applying one coat of aluminium paint Make : Super Thermolay of STP or equivalent in TEXSA India Ltd / IWL Ltd / Tiki Tech

M&L for plastering 10 mm in cement and sand mortar (1:3) using 100 % course sand on roof mied with and including WPC @ 3% by weight of cement and finished the surface even and smooth without using extra cement.

Day to day complaints for the following works :-

(a) Complaint related to carpenter works like door easing, door repair, kitchen cup board repair, window/door wire mesh/glass pane repair, refixing of building hardware etc by deploying carpentor and mazdoor.

(b) Removing blockage from water closet,floor or gully or Nahani trap and bends by rodding thoroughly and pouring water under pressure and cleaning,clearing the drainage to efficient and smooth flow of sludge/waste water all as specified and directed by Engg-in-charge.

(c) Cleaning of sewage pipe line (RCC / SGSW) by mechanical means such as Rottary cutter etc incl removal of roots inside the pipe etc, including rodding manually or mechanically from manhole to manhole and removing the waste materials / sludge disposing to a distance n exc 50 m and burying in borrow pits and covering with mud all as directed of any diameter of pipe etc complete all as specified and directed by Engineer-in-Charge Note:- (i) Contractor shall take all Precantionery measures during cleaning of sewage line / septic tanks etc. (ii) Contractor shall provide First Aid box, shoes, hand gloves, mask & required clothing to the workers at site. (iii) It shall be the responsibility of Contractor that if any mishap happens at site, Govt shall not be liable to pay any type of compensation.

Notes for Ser item Nos 122 (a) to 122 (c) :-The quoted rate of contractor shall comprise the following :-

Note:- (i) Contractor will establish a well furnished complaint cell to recieve the complaints (Petty repair) in the md accn as per location allocated by Enginner-in-Charge/GE. (ii) Contractor will deploy a Data Entry operator staff to recieve the complaints made by users in complaint cell from time 9:00 AM to 17:00 PM on all working day. (iii) Contractor will deploy sufficient plumber/ Carpentor/ Mason/ safaiwala/ electrician to attned the daily complaints (petty repair) on daily basis. Attendance report of the deployed skilled staff alongwith their healper will be submiited to JE/Engineer-in-Charge on daily basis. (iv) Contractor's supervisor will report on all working days alongwith their skilled staff and printed contractor's firm name complaint slip book at 8:30 hrs at JE/Engineer-in-Charge received complaints from users and to submit completion report/constraints, if any on the same day by 1700 hrs. (v) Printed complaint slip book as per format approved by Engineer-in-charge shall be provided and maintained by the contractor.

(vi) If there is any major complaints of tilling/Plumbing/Joinery/ electrician/BS for which additional times/manpowers or T&P as required the same shall be provided by the contractor without any extra cost to Govt. The same will be reoprted to JE/Engineer-in-Charge for taking consent. (vii) If the complaints will not be attended a recovery @ Rs. 1000 per day shall be recovered from the amount due to the contracor. (viii) Store for attending the complaints will be provided by the contractor on daily basis. (ix) Rate quoted in above BOQ shall be deemed to incl the cost of office staff/ office equipment, required T&P/stores and device etc alongwith sufficinet skilled manpowers/ labour to attend/complete the complaints in the same day duly signed by users at the entire satisfaction of Engineer-in Charge. (xii) Access will be given to contractors rep to the mobile application developed by Dept to monitor the complaints.

Preparing the old painted surfaces of following steel furniture by removing old paint & touching up with Red oxide primer where necessary & denting where necessary & preparing the surfaces & spray / mannualy painting with two coat of synthetic enamel paint as per existing colour of articles all as specified & directed. NOTE : Spray painting shall be carried out mechanically.

(a) Almirah med steel W/S FD-67, 1032

(b) Almirah large steel W/S (FD-67, 1031)

(c) Book Case steel (Glass door) (FD-90, 1028)

(d) Charpoy IP Steel Hardtop FD/MAP-II/01

(e) Table 900 x 600 W/O drawer (FD-1007)

(f) Table 900 x 600 with drawer (FD-1008)

(g) Chair Steel W/O arms (FD-75M)

(h) Chair CB Steel W/Arm (FD-75M )

(j) Table Office Offr Steel (FD-84,1003,1002 )

(k) Table Office Clerk Steel (FD-84 ,1004)

(l) Table dinning OR (FD-165M)

(m) Charpoy Double Bunk (FD-112)

(n) Trestle Store Room Steel (FD-1043)

(o) Stool Steel (FD-81, TP, 1028, 1026 )

(p) Rack Steel (FD-1038 & TP)

(q) Chair Writing Steel (FD-360)

(r) Form without Back 1900mm (TP)

(s) Almirah MAP Steel (FD-1030)

(t) Table 900 X 500 with Steel legs (TP)

(u) Rack Side 3/4 Spaces Steel (FD-1023)

(v) Table 1520X860X760MM Steel (FD-1010)

M&L One coat of french polish on wooden surface of any width or girth incl scrapping and cleaning for the following wooden furniture items all as per drg and as directed by Engineer-in-charge.

(a) Almirah large with shelves (DB-4116)

(b) Almirah medium with shelves (DB-4232)

(c) Book shelf open large (FD-13, DB-4121)

(d) Book case small (DB-4071)

(e) Chair writing (FD-250, 280)

(f) Hat stand W/M (FD-233)

(g) Peg Table (FD-25,277)

(h) Teble centre (FD-274, 235)

(j) Teapoy FD (FD-232,278,382)

(k) Table writing (FD-24,249,275)

(l) Table 3' x 2' W/O drawer (FD-284,231,42)

(m) Table 3' x 2' with drawer (FD-41,283,224)

(n) Sofa Set 05 Seater (FD-281)

(o) Table Office Clerk (DB-4120)

(p) Table Office Officer (DB-4119)

(q)Table Center 2 Tier (FD-375)

(r)Table Conference 16 Person (TP)

Removing the existing unserviceable top from following Tables and supply and fixing new top made out of 18/19 mm thick prelaminated MDF board including 4 mm thick Teak Wood beading alround the top. Colour of MDF board as approved by Engr - in- charge.

(a) Table Conference 16 Person (TP)

(b) Table 2'X2' (FD-293)

(c) Table 5'X2'-10" (FD-289)

(d) Table Writing Med (DB-3987)

(e) Table Executive Officer (TP)

(f) Table Center 2 Tier (FD-375)

(g) Table 1520X860X760MM Steel (FD-1010)

(h) Table Computer (TP)

(j) Table Office Offr Steel (FD-84,1003,1002 )

(k) Table Office Clerk Steel (FD-84 ,1004)

Removing of existing 12mm thick commercial plywood from following Charpoy and supply and fix new commerical plywood 12mm thick BWP IS 710 grade of Make:- Kitply / Greenply / Archidply and screw down to the mild steel square tube with appropriate machine screw and nut complete all as directed.

(a) Charpoy Double Bunk (FD-112)

(b) Charpoy IP Folding (FD-388 (R) )

Removing of existing UNSV Foam and Teapstry Cloth of Seat & Back from following Chairs and supply and fix new 32 density Foam Cushion with Taperstry cloth as approved by Engr-In-Charge.

(a) Chair Easy Cushioned (FD-358)

(b) Chair Writing Steel (FD-360)

(c) Chair Revolving Executive (TP)

(d) Chair Visitor (TP)

(e) Chair Conference (TP)

(f) Chair Computer (TP)

(g) Chair Writing MAP (FD/E6/MAP/12)

Removing of existing UNSV Cushion with Cover of Seat/Back from Sofa Sets of Size 21"X22" and Supply new Cushion with Cover of 100 thick cushion 40 Density of Foam alongwith cover of tapestry cloth duly stiched Note : Tapestry Cloth shall be make of Bombay Dying/ Raymond Furnishing/ D'Decor (Tapestry cloth rate should not be less than Rs. 300 per mtr). Colour of cloth shall be approved by Engr-in-Charge. Make of F oam : Sleepwell/ Springwell/ Kurlon. (FD-281)

Removing the existing torn out/unsv Tepestry cloth/Cushion complete from Seat and Back from Sofa Set 05 Seater and replacing with new cushion having 40 Density for seat and Back alongwith cover of with Teapstry cloth duly stiched with best thread. Note : Tapestry Cloth shall be make of Bombay Dying/ Raymond Furnishing/ D'Decor (Tapestry cloth rate should not be less than Rs. 300 per mtr). Colour of cloth shall be approved by Engr-in-Charge. Make of Foam : Sleepwell/ Springwell/ Kurlon. (TP )

Chair Executive Revolving (TP)

(a) Removing the existing damaged/unsv pedestal assembly of sorts and providing and fixing with new SS pedestal assembly with five numbers twin wheels castors complete. All as specified and directed by Engr-in-Charge.

(b) Removing the existing damaged/unsv Hydraulic assembly of sorts and providing and fixing with new Hydraulic assembly and make good the center Pivot mechanisam of Revolving Chair including tilt tension adjustment complete. All as specified and directed by Engr-in-Charge.

Almirah Large Steel with Shelves (FD-1031)

(a) Removing the existing unserviceable shelves of Almirah Large Steel with Shelves providing new shelves made with mild steel sheet, 1 mm thick, cut to size, shape etc duly welded and applying two coats of synthetic enamel paint over a coat of red oxide primer by sprayer complete.

(b) Removing the existing unserviceable Legs of Almirah Large Steel with Shelves providing new legs made with mild steel sheet, 1 mm thick, cut to size, shape etc duly welded and applying two coats of synthetic enamel paint over a coat of red oxide primer by sprayer complete.

(c) Removing the UNSV threeway locking system with lock and handle from Almirah Large steel with shelves supply and fix new threeway locking system with lock and handle. Make of lock shall be Godrej / Harrison.

(d) Removing the existing unserviceable Door of Almirah Large Steel with Shelves and supply and fix new Door made with mild steel sheet, 1 mm thick, cut to size, shape as per drg and applying two coats of synthetic enamel paint over a coat of red oxide primer by sprayer complete.

Almirah Med Steel with Shelves (FD-1032)

(a) Removing the existing unserviceable shelves of Almirah Med Steel with Shelves providing new shelves made with mild steel sheet, 1 mm thick, cut to size, shape etc duly welded and applying two coats of synthetic enamel paint over a coat of red oxide primer by sprayer complete.

(b) Removing the existing unserviceable Legs of Almirah Med Steel with Shelves providing new legs made with mild steel sheet, 1 mm thick, cut to size, shape etc duly welded and applying two coats of synthetic enamel paint over a coat of red oxide primer by sprayer complete.

(c) Removing the UNSV threeway locking system with lock and handle from Almirah Med steel with shelves supply and fix new threeway locking system with lock and handle. Make of lock shall be Godrej / Harrison.

(d) Removing the existing unserviceable Door of Almirah Med Steel with Shelves and supply and fix new Door made with mild steel sheet, 1 mm thick, cut to size, shape as per drg and applying two coats of synthetic enamel paint over a coat of red oxide primer by sprayer complete.

Removing the existing unserviceable shelves from following Steel Racks providing new shelves made with mild steel sheet, 1 mm thick, cut to size, shape etc duly welded and applying two coats of synthetic enamel paint over a coat of red oxide primer by sprayer complete.

(a) Rack Steel 6 Tier (FD-1038)

(b) Rack Steel 7'x 3" x 3' x x1.3" with 9 shelves (TP)

(c) Rack Side 3/4 Spaces steel (FD-1023)

Removing the existing unserviceable Back from the following Steel Racks with providing new Sides made with mild steel sheet, 1 mm thick, cut to size, shape etc duly welded and applying two coats of synthetic enamel paint over a coat of red oxide primer by sprayer complete.

(a) Rack Steel 6 Tier (FD-1038)

(b) Rack Steel 7'x 3" x 3' x x1.3" with 9 shelves (TP)

Removing the existing unserviceable Sides from the following Steel Racks with providing new Sides made with mild steel sheet, 1 mm thick, cut to size, shape etc duly welded and applying two coats of synthetic enamel paint over a coat of red oxide primer by sprayer complete.

(a) Rack Steel 6 Tier (FD-1038)

(b) Rack Steel 7'x 3" x 3' x x1.3" with 9 shelves (TP)

M/s AG PATHAN (BID ID -3375195)

AMAR CONSTRUCTION (BID ID -3376159)

M/s. R. R. ASSOCIATES (BID ID -3375213)

Arihant Construction (BID ID -3375961)

HG PATHAN CONSTRUCTION COMPANY (BID ID -3375686)

DHANANJAY BABAN KALANE (BID ID -3375902)

MATOSHREE CONSTRUCTION (BID ID -3375966)