Interior Renovation And furnishing works at ED Office (Ground, 1st and 2nd floor), NBCC Square, Newtown, Kolkata.

Sr. No. DESCRIPTION TOTAL AMOUNT (Rs.)

GRAND TOTAL (DSR + Non-DSR/MR) 238,194,412.48

CEMENT CONCRETE: Providing and laying in position CEMENT CONCRETE of specified grade exluding the cost of centring and shuttering-all work upto plinth level.

4.1.8 1: 4: 8 (1 Cement: 4 coarse sand: 8 graded stone aggregate 40mm nominal size) CUM 600.00 6812.00 0.973 6628.08 3976845.60

RAISED FALSE FLOOR: Providing and fixing removable raised/false access flooring with systemand its components of approved make for different plenum height

with possible height adjustment upto 50mm, comprising of modular loadbearing floor panels supported on G.I. rectangular stinger frame workand G.I. Pedestal etc. all

complete, as per the architectural drawings, as specified and as directed by Engineer-in-charge consisting of:

(a) Providing at required spacing to form modular framework, pedestals made out of GI tube of thickness minimum 2 mm and 25 mm outer diameter, fully welded on to

the G.I. Base plate of size 100mm x 100mm x 3mm at the bottom of the pedestal tube, G.I. pedestal head of size 75mmx75mmx3.5 mm welded with GI fully threaded

stud 16mm outer diameter with two GI Check nuts screwed on the stud for level adjustment upto 50mm, locking and stabilizing the pedestal head in position at the

required level. The pedestals shall be fixed to the subfloor (base) through base plate using epoxy based adhesive of approved make or the machine screw with rawl

(b) Stringers system in all steel construction hot dipped galvanized ofrectangular size 570x20x30x0.80mm thick having holes at both ends for securing the stringers on

to the pedestal head using fully threaded screws ensuring maximum lateral stability in all directions, the grid formed by the pedestal and stringer assembly shall receive

the floor panel, this system shall provide adequate solid, rigid support for access floor panel, the system shall provide a minimum clear uninterrupted clearance

11.54 between the bottom of the floor for electrical conduits and wiring etc. all complete as per the architectural drawings, as specified and as directed by the Engineer-in-

(c) Providing and fixing Access Floor panel of 600x600x32 mm medium grade Filled Steel anti static high pressure Lamination of 800H grade (FS800H). Access Floor

panel shall be steel welded construction with an enclosed bottom pan with uniform pattern of 64 hemispherical cones. The top and bottom plates of Steel Gauges: top

0.6 mm and bottom 0.7 mm fused spot welded together (minimum 64 welds in each dome and 20 welds along each flange). The panel should be Corroresist epoxy

coated for lifetime rust protection and cavity formed by the top and bottom plate is filled with Pyrogrip noncombustible Portland cementitious core mixed with lightweight

foaming compound. The access floor shall be factory finished with Anti-static High Pressure laminate with Non Warp technology upto 1mm thickness for superior

adhesion and Surface flatness within 0.75mm.The panel is to withstand a Concentrated Load of 363 kgs applied on area 25mm x 25mm without collapse in the centre

of the panel which is placed on four steel blocks. The panel will withstand and Uniformly Distributed Load (UDL) minimum 1250 kg/sqm and an impact load of 50kg all

complete as per the approved manufacturers specification and as per the direction of Engineer-in-charge. All specification must be printed on the side of the panel to

ensure the quality of the product.

ALUMINIUM SKIRTING: Supply of 100mm Aluminium (Grade 6063) Skirting with 15 micron anodising In Natural Finish. Thickness 1.30 to 1.50mm. Designed to

conceal screws. Seamless finish. Complete with Rubber/ PVC Jointers and Gasket.

LAMINATED WOODEN FLOORING: Providing and laying 8mm thick AC5 grade laminate wooden flooring having good castor chair and furniture resistance strength.

Plank dimension to be 606x103 mm with clock locking system and wax coating for better sound resistance. Impact and abrasion resistance to be of high grade having

class EN 13329. The flooring shall be laid with 2mm thick underlay and PVC sheet and prevent against moisture and foot taping sound. The item also includes the

skirting and any other profiles required for proper installation.

VITRIFIED TILES: Providing and laying vitrified floor and wall tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than

1.05 11.41A 0.08% and conforming to IS: 15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement: 4 coarse sand), jointing with grey

cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc., complete.

Grouting the joints of flooring tiles having joints of 3 mm width, using epoxy grout mix of 0.70 kg of organic coated filler of desired shade (0.10 kg of hardener and 0.20

1.06 kg of resin per kg), including filling/ grouting and finishing complete as per direction of Engineer-in-charge.

CARPET TILES: Providing and laying carpet tile flooring. Carpets shall be of Type 6 nylon loop pile carpet tiles/Plank. The carpet shall have sufficient gauge (1/10 ~

1/12) with sufficient stitches (10~13) per inch. The carpet shall be solution dyed fibre content or with injection printing technology. The carpet shall have the pile height

ranging from (2.0 ~ 3.0) mm with average density higher than 4500 Oz/ cubic yard. The total thickness of the carpet tile shall also range from (5.5 ~ 6.0) mm.

Kota stone slab flooring over 20 mm (average) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab, including

1.08 rubbing and polishing complete with base of cement mortar 1: 4 (1 cement: 4 coarse sand):

GRANITE: Providing and laying Polished Granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as

per the architectural drawings with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1: 4 (1 cement: 4 coarse sand) laid and jointed with

11.56 cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing, curing and polishing etc. all complete as specified and

as directed by the Engineer-in-Charge.

11.56.1 Polished Granite stone slab of colour Black, Cherry/Ruby Red or equivalent sq m 100.00 4481.30 0.973 4360.30 436030.49

IPS FLOORING: 52mm thick cement concrete flooring with concrete hardener topping, under layer 40 mm thick cement concrete 1:2:4 (1 cement : 2 coarse sand : 4

graded stone aggregate 20 mm nominal size) and top layer 12mm thick cement hardener consisting of mix 1:2 (1 cement hardener mix : 2 graded stone aggregate 6

mm nominal size) by volume, hardening compound mixed @ 2 litre per 50 kg of cement or as per manufacturer's specifications. This includes cost of cement slurry,

but excluding the cost of nosing of steps etc. complete.

STEEL FRAMING: Structural steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and

applying a priming coat of approved steel primer all complete.

1 Digitally signed by ASHWANI

S NO DSR/MR Cess DSR Rate AMOUNT (Rs.)

DESCRIPTION UNIT QTY RATE

DSR 2023 VOL-1 Factor i/c factors (DSR) (NON DSR)

STEEL FRAMING: Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying

a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete.

Steel Work welded in built / framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as

1.13 required.

10.25.2 In gratings, frames, guard bar, ladder, railing, brackets, gates and similar works Kg 500.00 172.60 0.973 167.94 83969.90

RUBBER FLOORING: Providing and Fixing of Rubber flooring 20mm thick with adhesive ,installation, suitable for gymnasium flooring complete in all respects.Classic

rubber flooring is a tough, resilient, and safe choice for any active venue that endures intense use from athletes, and gym fitness fanatics.

TOTAL FLOORING WORKS 17,333,896.10 5,598,250.30

2 FALSE CEILING WORKS

GYPSUM BOARD CEILING: Providing and fixing false ceiling at all height including providing and fixing of frame work made of special sections, power pressed from

M.S. sheets and galvanized with zinc coating of 120 gms/sqm (both side inclusive) as per IS : 277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thick

with flanges of 27 mm and 37mm, at 1200 mm centre to centre, one flange fixed to the ceiling with dash fastener 12.5 mm dia x 50mm long with 6mm dia bolts, other

flange of cleat fixed to the angle hangers of 25x10x0.50 mm of required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate

G.I. channels 45x15x0.9 mm running at the spacing of 1200 mm centre to centre, to which the ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered

flanges of 26 mm each having lips of 10.5 mm, at 450 mm centre to centre, shall be fixed in a direction perpendicular to G.I. intermediate channel with connecting clips

made out of 2.64 mm dia x 230 mm long G.I. wire at every junction, including fixing perimeter channels 0.5 mm thick 27 mm high having flanges of 20 mm and 30 mm

2.01 12.45 long, the perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450 mm centre, with 25mm long dry wall screws @ 230 mm interval, including fixing of

gypsum board to ceiling section and perimeter channel with the help of dry wall screws of size 3.5 x 25 mm at 230 mm c/c, including jointing and finishing to a flush

finish of tapered and square edges of the board with recommended jointing compound , jointing tapes , finishing with jointing compound in 3 layers covering upto 150

mm on both sides of joint and two coats of primer suitable for board, all as per manufacturer's specification and also including the cost of making openings for light

fittings, grills, diffusers, cutouts made with frame of perimeter channels suitably fixed, all complete as per drawings, specification and direction of the Engineer in

Charge but excluding the cost of painting with

12.45.1 12.5mm thick tapered edge gypsum plain board conforming to IS: 2095- (Part I) :2011 (Board with BIS certification marks) sq m 4500.00 1355.80 0.973 1319.19 5936370.30

WOODEN VENEER/ BAMBOO CEILING: Providing and fixing wooden veneer/ bamboo ceiling by Fixing Natural OAK Veneer 4 mm/ natural bamboo shoots, mesh,

2.02 MR screens, gall screen complete as per the design on 12mm UnderlayFire retardent Ply fixed to a subframe made using 50mm x 50mm Kiln seasoned and chemically sq m 204.80 7500.00 1,536,000.00

treated hollock wood fixed to RCC ceiilng using Fastners .

2.03 13.68 French spirit polishing:

13.68.1 Two or more coats on new works including a coat of wood filler sq m 204.80 446.25 0.973 434.20 88,924.42

LOUVERED WOODEN FALSE CEILING & WALL PANELS: Providing and fixing CUSTOM Channeled woodwork ceiling panel600 DENSITY / fire Test certificate as

per BS_476 part 7) acoustic wall panel of width of 192mm with finishing of 15 mm thick Grooved wooden acoustic panel of size 2400 mm, Groove Size 3mm at an

RANDOM interval of 13MM,21mm,42MM, and28 mm , the wooden acoustic panels to be backed with black acoustic fleece with NRC of 0.6 the edge of panel shall be

Tongue and groove to be fixed with clips on The grid should be of “BOLLARD” make with 24mm wide T - section flanges color white. The main T runner with length

and size of 24X38mm made from .30mm thick sheet spaced at 1200mm Centre to Centre and cross T of size 24X38mm made of .3mm thick of 1200mm long spaced

2.04 MR between main T at 600mm center to centre to form a grid of 1200X600mm and second cross T of length 600mm and size 15X38mm made of 0.30mm sheet to be sq m 100.00 4000.00 400,000.00

interlocked at middle of the 1200X600 mm panel to form grid of 600X600mm and wall angle of size 19X19 The grid frame should be suspended from ceiling using M-6

fastener, L Cleat, threaded rod of galvanized steel 6mm dia along with L shape Grid holder which will be fixes to Main Runner at spaced of 1200 c/c.

Formaldehyde: E1-M1 ck Grade 1 C55 galvanized spring steel of dimension 100 x 20mm and 4 mm aquiline wire to be used for level adjustment during installation

purpose in main runners.

PERFORATED GYPSUM BOARD CEILING: Providing and fixing suspended false ceiling- Danoline: Solopanel Size 1188x1998x12.5mm Globe perforation 8/18 with

8.7% perforation with NRC upto 0.6 : Regular round perforation of glass fibre reinforced gypsum material, which includes providing and fixing GI perimeter channels of

size 0.55 mm. Thk. having one flange of 20 mm and another flange of 30 mm and web of 27 mm along the perimeter of the ceiling, screw fixed to brick wall/ partition

with help of nylon sleeves and screws, at 610 mm centers. The suspended GI intermediate channels of size 45 mm,0.9mm thk with two flanges of 15 mm each from

the soffit at 900 mm centers with ceiling angle of width 25mm x 10mm x 0.55mm thk fixed to soffit with GI cleat and steel expansion fasteners. Ceiling section of 0.55

mm thk having web of 51.5mm & two flanges of 26mm each with lips of 10.5mm are fixed to the intermediate channels with help of connecting clips and in direction

2.05 MR perpendicular to the intermediate channel with centers of 333 mm perforated gypboard is then screw fixed to ceiling section with 25 mm dry wall screws at 300 mm sq m 160.00 3100.00 496,000.00

centers to G.I. framing in perfect level. Screw fixing is done mechanically either with screw driver or drilling machine with suitable attachment. Finally the boards are to

be joined and finished so as to have a flush look with uniflot.

Cleaneo Technology - Air purification & Air quality.Active reduction of air polluants thanks to Cleaneo Technology effectively reduces concentrations of VOC’s like

alcohol, aldehydes, ketons and esters as well as unpleasant odours from e.g. food or cigarette smoke

Air purification properties tested according to CEN standards and VDI guidelines by Fraunhof Insistute for Building Physics.

The false ceiling surfaces shall be prepared to the satisfaction of the Architect, and shall be applied with two coats of primer to the satisfaction of Architects.

300x1200 SUSPENDED FALSE CEILING: Providing and fixing suspended false ceiling microlook tegular edge tile with 15 mm thickness ,easily demountable tile ,

manufactured from High density glass wool , visible surface is a batch painted glass tissue in white, back of the tile covered with glass tissue. Size 1200x600x15mm

Acoustics-Sound absorption(Alpha W) - 0.95 at 200 mm o.d.s as per EN ISO 354 Acoustics-Sound absorption Class - Class A at 200 mm o.d.s as per EN ISO

2.06 MR 11654Acoustics-Articulation class - 180 as per ASTM E1111, ASTM E1110,NRC - 0.9 NRC as per ASTM C 423,Humidity Resistance -Permanent ambient RH up to sq m 1000.00 3000.00 3,000,000.00

95% at 30*C without sagging, warping and delaminating ( 13964:2014). Fire Safety - Tested and classified as non combustible according to EN ISO 1182 with reaction

to fire classification class A2 s1 d0 according to EN 13501-1 - European Standard.

2 Digitally signed by ASHWANI

S NO DSR/MR Cess DSR Rate AMOUNT (Rs.)

DESCRIPTION UNIT QTY RATE

DSR 2023 VOL-1 Factor i/c factors (DSR) (NON DSR)

METAL CEILING FOR WET AREAS : Providing and fixing G.I Plain 84mm wide x12mm deep panel with 16 mm flush profile to make it 100mm module of length upto

6mtr, shall be roll formed out of 0.5mm thick Powder Coated .The top coat of panel shall be 60 micron polyester coated finish in approved colour. The panel shall be

factory cut in up to 6Mtr OR required length. Accessories Detail:Carrier: 32 mm wide and 39mm deep, made out of 0.5mm thick steel backed with enameled black paint

having cut out to hold on panel in a module of 100mm closed. The joint of two carriers shall be joined by means of carrier splices maintaining a module of 100mm

.4mm dia galvanized rod with special height adjustment butter fly clips made out of SS steel sheet. The edge profile G.I.shall be matching with the panel.

ACOUSTIC PET PANEL CEILING : Supply of 12mm HD PET panels with density of 2400GSM form 60 colour options with customized pattern as per the designers

requirement, the panel shall be made from-

-100% polyester fiber, with up to 70% recycled fiber. size of panel 2800mm x 1200mm (± 0.5mm).

Panel Should be mostiure resistant and also Non-toxic, non-irritant, and fire-compliance with safety standards confirm to Class 1 Fire Ratings tested as per BS 476

Part 6 (Fire Propagation) & Part 7 (Surface spread of flame) for interior applications. ASTM E84 class A, ASTM D 2859, BS 5852 PART 1.

Noice reduction coefficient (NRC) - 0.45 with direct fix method, can be achive upto 0.70 with 50 mm gap with pet wool infill and Thermal

2.08 MR conductivity ASTM C 518 upto 0.05 w/mK. sq m 69.12 4200.00 290,304.00

The product should be 100% make in india and resistance to fungal growth As Per ASTM C 518.

OEM must have own manufacturing plant along with ISO CERTIFICATIONS- complying to- IGBC Membership,

ISO 14184-2 (Release formaldhyde)

ISO 9001 (Quality Mangement System)

ISO 14001 (Environmental Management System)

ISO 45001 (Ocupational helth & safety management system)

TOTAL FALSE CEILING WORKS 6,025,294.72 6,822,304.00

3 WALL FINISHES WORKS

SINGLE GLAZED FIXED PARTITION WITH 10MM GLASS): Supply & Installation of Aluminium Partition with Clip-on / U-Section of size 30mm x 21mm with 2.5mm

Wall thickness in matt black/ Natural Alu finish. Partition to be provided with suitable gaskets for insertion of 10mm thick clear toughened glass. Partition Glass joineries

consists of two-way Polycarbonate I-profiles, 90 Degree Polycarbonate L-Junction and Polycarbonate T-Junction profiles. Polycarbonate profile joineries to be fixed

3.01 MR with double sided adhesive tape & profiles to be inserted in the joint instead of sealing it with sealants. Polycarbonate profiles to be used to give continuity glass effect. sq m 500.00 11180.00 5,590,000.00

Hardware for fixing profiles to be used as per manufacturer standard. Costs should be inclusive of necessary Hardware for fixing of profiles & installation charges.

SINGLE GLAZED STILE DOOR WITH 10MM GLASS: Supply & Installation of Single Glazed Stile Glass Door with aluminium profile of frame size 82X40mm along

with Door Rebate of frame size 55x32mm with seals matt black/natural anodized finish with specially designed Aluminium Hinges (4 Nos) & NLH 1011 Lever Handle in

Oval shape SS304 with SS 35mm Backset of 22mm Square Forend with Strike plate. Door should have Lock, oval escutcheons, strike plate, EPC One Side Key other

3.02 MR side knob-70mm and Door closer with EN 3 standard rating and tested as per EN 1154 for upto 500,000 Cycles of door operation. Door consist of 10mm toughened Nos. 55 90000.00 4,950,000.00

glass and necessary seals to be provided all around the door frames and drop down seal. Cost should be inclusive of installation charges.

WOODEN DOOR FRAMES: Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold

3.03 fast lugs or with dash fasteners of required dia & length (hold fast lugs or dash fastener shall be paid for separately).

WOODEN BATTENS: Providing and fixing specified wood frame work consisting of battens 50x25mm fixed with rawl plug and drilling necessary holes for rawl plug

3.04 etc. including priming coat complete.

8.27.1 Kiln seasoned and chemically treated hollock wood CUM 2.00 187277.65 0.973 182221.15 364442.31

Providing and fixing ISI marked flush door shutters conforming to IS: 2202 (Part 1) decorative type, core of block board construction with frame of 1st class hard wood

3.05 and well matched teak 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters.

9.20.1 35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws SQM 423.36 3473.85 0.973 3380.06 1430980.53

3.06 9.24 Extra for providing vision panel not exceeding 0.1 sqm in all type of flush doors ( cost of glass excluded ) SQM 423.36 199.15 0.973 193.77 82035.72

9.24.1 Rectangular or square

WOODEN LIPPING: Extra for providing lipping with 2nd class teak wood battens 25 mm minimum depth on all edges of flush door shutters (over all area of door

shutter to be measured).

Providing and fixing double action hydraulic floor spring of approved brand and manufacture conforming to IS : 6315, having brand logo embossed on the body / plate

with double spring mechanism and door weight upto 125 kg, for doors, including cost of cutting floors, embedding in floors as required and making good the same

3.08 matching to the existing floor finishing and cover plates with brass pivot and single piece M.S. sheet outer box with slide plate etc. complete as per the direction of

Engineer-in-charge.

21.4.2 With brass cover plate minimum 1.25 mm thickness SET 173.00 2966.10 0.973 2886.02 499280.65

FLUSH DOOR HANDLE :H type pull handle size 25 x 450mm C/C includes Stainless steel back to back fixing accessories for steel,wood & glass door : 302 grade

WOODEN DOOR LOCK: Providing and Fixing LOCK ML DL 72/55, Dead lock in 55mm backset includes strike plate and CYLINDER EPC K35/K35, double cylinder in

70mm length with 3keys and fixing , handle LH 100 Escutcheon round Finish: BSS

3 Digitally signed by ASHWANI

S NO DSR/MR Cess DSR Rate AMOUNT (Rs.)

DESCRIPTION UNIT QTY RATE

DSR 2023 VOL-1 Factor i/c factors (DSR) (NON DSR)

GLASS FILMS: Providing & Fixing Frosted Translucent, cast PVC, self-adhesive vinyl, special CRYSTAL-effect film to reproduce Sand-blasting effect on glass with

customised designs, thickness of 2 mil (0.05mm) without adhesive & 3mil (0.8)with adhesive having minimum tensile strength of 3.5 pound/inch at 73 F(0.6 kg/cm at 23

C). Adhesion after 24hrs of installation should be 4 pounds/inch (0.7 kg/cm) on Acrylic, Glass Polycarbonate: MCS warranty of 3yrs (if exposed to direct sunlight) to

15yrs (indoors) .

LACQUERED GLASS: Providing and fixing of 6mm thick annealed SGG Planilaque Evolution (premium GRIHA rated lacquered glass from Saint-Gobain) of approved

color by Architect/ Client / Customer, fixed with SGG ULTRAFIX (compatible neutral core silicon/ double sided tape) on a perfectly leveled 12mm thick water proof

marine plywood / MDF / Mineral fibre board which is mounted on the RCC wall/any other structure. Lacquered glass must be made industrially (via curtain coating

3.12 MR process); opaque (if viewed against a support wall), coated with PU lacquer (50 micron thick); color consistency (measured by Minolta spectrophotometer CM5081); SQM 698.14 5004.00 3,493,492.56

highly durable (passes PERSOZ hardness test for minimum 220 oscillatios); humid resistant (conforms to BS EN 1036 1999); environmentally friendly (no lead, no

arsenic, no copper, noformaldehyde); appropriate recycled content (12% post industrial/ 6% post consumer); compressive strength (1000 MPa) & tensile strength (40

MPa), same as float glass;

WPC BOARD PARTITION: Providing and fixing 12 WPC board partition upto ceiling height consisting of Aluminium frame and required board, including providing and

fixing of frame work made of aluminium sections 50x50mm, consisting of floor and ceiling channel 50mm wide, fixed to the floor and ceiling at the spacing of 600 mm

3.13 MR centre to centre with dash fastener of 12.5 mm dia meter 50 mm length or suitable anchor fastener or metal screws with nylon plugs. 75 mm overall thickness partition SQM 150.00 3000.00 450,000.00

with 12 mm thick WPC board as per approved specifications.

Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias

and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with

white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing of edges to give high gloss finish etc. complete at all

8.2.2 Granite stone slab of colour black, Cherry/Ruby red

WINDOW BLINDS : WINDOW BLINDS: Providing & supplying of Window Blinds as per the approved sample double honeycomb blackout shades having

honeycomb within honeycomb with easy rise operating system as per following specifications fabric specifications:

• Original Non-woven honeycomb shade shaving soft fabric appearance and high energy-efficient fabric with high tear strength constructed out of Anti-

static, resilent, colour fast & Sanitized Treat 100% spun bonded non-woven polyester fiber & precision manufacture to form a hexagonally shaped duette

pleat. The Fabric is GREENGUARD certified and can attain an NRC value of 0.75. Certificates to be provided at the time of delivery of material at site. Pleat dimension

¾ ”Honeycomb within a Honeycomb” with 3 air pockets for maximum energy efficiency.

• Shadings are duotone, with neutral tone facing the exterior and color facing the interior The Head rail. Shall measure 50 wide and 35mm deep & thick 1.25mm

extruded from alu. alloy& shall be powder coated to a smooth finish with a thickness of 40 microns. Fabric shall be constructed from spun-bonded

3.15 MR polyester fiber, precision manufactured to form a hexagonally shaped, dual pleat, cellular construction. All cords & cord holes shall be fully concealed SQM 450.00 21200.00 9,540,000.00

inside the fabric structure. As each of the hexagonal cells is formed individually, pleats operate independent of each other providing superior pleat

retention & structure strength. Installation brackets. shall be of high-tension spring steel suitable for overhead & wall mounting 30mm Duette Hartford mounting

bracket. Head rail covered with Sydney Valance of height 80mm made up of Aluminium & L shape moving Rail includes “Click & Engage" method of dimension

50mmx55mmsticked with integrated moving rail magnets provide a streamlined look, reduce centre light gap, and promote easier operation. Polyester cord. Shall be

0.9mm in diameter & of woven hollow core end cap shall be moulded acrylic color matched to the head & bottom rails. Bottom rail shall be a single channel

section, measuring 30mm wide and 12.5mmdeep & thickness 1-1.2mm extruded from Alu. Alloy & shall be powder coated with a smooth finish to a thickness of

15-25 microns. Hold-Down bracket (optional) shall be molded in clear acrylic. It incorporates a pin for engagement with the bottom rail end-cap. It shall be suitable for

sill, face or side facing. Cord Equalizer shall be injection melded from impact modified acrylic with a high flexural modulus

PELMET: Fabricate and install pelmet made of 19mm thick board, up to 300mm high and in line with external glazing as per details of Architect. Rate to include

finishing exposed surfaces of the Pelmet with 1mm laminate.

3.17 13.26 Providing and applying plaster of paris putty of 2 mm thickness over plastered surface to prepare the surface even and smooth complete sqm 2500.00 262.70 0.973 255.61 639017.75

13.85 Applying priming coats with primer of approved brand and manufacture, having low VOC (Volatile Organic Compound ) content.

13.85.3 With water thinnable cement primer on wall surface having VOC content less than 50 grams/litre sqm 6000.00 73.95 0.973 71.95 431720.10

Wall painting with premium acrylic emulsion paint of interior grade, having VOC (Volatile Organic Compound) content less than 50 grams/ litre of approved brand and

manufacture, including applying additional coats wherever required to achieve even shade and colour.

5.5mm THICK HDHMR BOARD (BOTH SIDE RAW): Providing and fixing in wall lining, partitions etc. Confirming to ASTM E-84-2021 class1 both side raw, having even

MR grade low emission, high moisture resistance, fire resistance, borer, termite & fungus resistance, green material and environmental friendly with necessary fixing Sqm 3000.00 504.00 1,512,000.00

arrangement and screws etc. , complete as per direction of Engineer-in-Charge

5.5mm thick HDHMR Board

11 mm THICK HDMR BOARD (BOTH SIDE RAW): Providing and fixing 11mm thick HDHMR board in wall lining, partitions etc. both side raw. Extra density, high

moisture resistance, borer, termite & fungus resistance, green material and environmental friendly with necessary fixing arrangement and screws etc. Complete

11 mm thick HDHMR Board SQM 3927.04 1079.00 4,237,276.16

ALUMINIUM FRAME: Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z

sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the

gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and

jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws, all complete as per

architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately) :

4 Digitally signed by ASHWANI

S NO DSR/MR Cess DSR Rate AMOUNT (Rs.)

DESCRIPTION UNIT QTY RATE

DSR 2023 VOL-1 Factor i/c factors (DSR) (NON DSR)

21.1.1.3 Polyester powder coated aluminium (minimum thickness of polyester powder coating 50 micron) Kg 8000.00 530.90 0.973 516.57 4132525.60

3.23 26.7 PARTITION INSULATION: Providing and Fixing 50 mm thick extruded polystyrene rigid Polyester rigid insulation boards for cavity as per specifications Sqm 6000.00 1004.55 0.973 977.43 5864562.90

VITRIFIED TILES FOR WALL CLADDING: Providing and laying Vitrified tiles in different sizes (thickness to be specified by manufacturer), with water absorption less

than 0.08 % and conforming to 1.S. 15622, of approved make, in all colours & shade, in skirting, dado, riser of steps, over 12 mm thick bed of cement mortar 1: 3 (1

11.46 cement: 3 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joint with white cement & matching pigments etc. complete.

3D ACOUSTIC PET WALL PANELLING: Supply of 12mm HD PET panels with density of 2400GSM form 60 colour options with customized pattern as per the

designers requirement, the panel shall be made from-

-100% polyester fiber, with up to 70% recycled fiber. size of panel 2800mm x 1200mm (± 0.5mm).

Panel Should be mostiure resistant and also Non-toxic, non-irritant, and fire-compliance with safety standards confirm to Class 1 Fire Ratings tested as per BS 476

Part 6 (Fire Propagation) & Part 7 (Surface spread of flame) for interior applications. ASTM E84 class A, ASTM D 2859, BS 5852 PART 1.

Noice reduction coefficient (NRC) - 0.45 with direct fix method, can be achive upto 0.70 with 50 mm gap with pet wool infill and Thermal

3.25 MR conductivity ASTM C 518 upto 0.05 w/mK. SQM 776.75 4200.00 3,262,350.00

The product should be 100% make in india and resistance to fungal growth As Per ASTM C 518.

OEM must have own manufacturing plant along with ISO CERTIFICATIONS- complying to- IGBC Membership,

ISO 14184-2 (Release formaldhyde)

ISO 9001 (Quality Mangement System)

ISO 14001 (Environmental Management System)

ISO 45001 (Ocupational helth & safety management system)

LAMINATE PANELLING: Providing & Fixing decorative high pressure laminated sheet of plain / wood grain in gloss / matt/ suede finish with high density protective

3.26 surface layer and reverse side of adhesive bonding quality conforming to IS : 2046 Type S, including cost of adhesive of approved quality.

TOTAL WALL FINISHING WORKS 20,222,627.93 34,317,763.22

4 MISCELLANEOUS WORKS

WATERPROOFING: Providing and laying water proofing treatment to vertical and horizontal surfaces of depressed portions of W.C., kitchen and the like consisting of:

(i) Ist course of applying cement slurry @ 4.4 kg/sqm mixed with water proofing compound conforming to IS 2645 in recommended proportions including rounding off

junction of vertical and horizontal surface.

4.01 22.3 (ii) IInd course of 20 mm cement plaster 1:3 (1 cement : 3 coarse sand) mixed with water proofing compound in recommended proportion including rounding off SQM 705.70 769.60 0.973 748.82 528442.84

junction of vertical and horizontal surface.

(iii) IIIrd course of applying blown or residual bitumen applied hot at 1.7 kg. per sqm of area.

(iv) IVth course of 400 micron thick PVC sheet. (Overlaps at joints of PVC sheet should be 100 mm wide and pasted to each other with bitumen @ 1.7 kg/sqm).

Disposal of moorum/building rubbish/ malba/ similar unserviceable, dismantled or waste material by mechanical transport including loading, transporting, unloading to

4.02 1.1.18 approved municipal dumping ground for lead upto 10 km for all lifts, complete as per directions of Engineer-in-charge. Note - item to be applicable in urban areas cum 25.00 494.10 0.973 480.76 12018.98

having directions for restricted hours for movement/ plying of load carrying motor vehicle of 3.5 cum or more.

4.1. Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level :

4.1.3 1:2:4 (1 cement : 2 coarse sand (zone-lll) derived from natural sources : 4 graded stone aggregate 20 mm nominal size derived from natural sources) cum 100.00 7878.50 0.973 7665.78 766578.05

5.9 Centering and shuttering including strutting, propping etc. and removal of form for

5.9.1 Foundations, footings, bases of columns, etc. for mass concrete sqm 200.00 392.15 0.973 381.56 76312.39

5.22A Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level.

5.22A.6 Thermo-Mechanically Treated bars of grade Fe-500D or more. kg 2000.00 107.85 0.973 104.94 209876.10

Brick work with non modular fly ash bricks conforming to 1S:12894, class designation 10 average compressive strength in super structure above plinth level up to floor

4.06 V level in:

6.4.1 Cement mortar 1:4 (1 cement : 4 coarse sand) cum 50.00 8962.35 0.973 8720.37 436018.33

6.45 Half brick masonry with non modular fly ash bricks of class designation 10, conforming to IS :12894, in super structure above plinth upto floor V level.

6.45.1 Cement mortar 1: 3 (1 cement: 3 coarse sand) sqm 2872.33 1132.50 0.973 1101.92 3165087.26

4.08 13.4 12 mm cement plaster of mix : 1:4 (1 cement: 4 coarse sand) sqm 5744.66 357.35 0.973 347.70 1997428.58

DEMOLITION & DISMANTLING WORKS

Demolition of brickwork manually/ by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead as per

the direction of the engineer in charge

Dismantling door, windows and clerestory widows (steel or wood) shutter including chowkats, architrave, holdfasts etc complete and stacking within 50 metres lead

5 Digitally signed by ASHWANI

S NO DSR/MR Cess DSR Rate AMOUNT (Rs.)

DESCRIPTION UNIT QTY RATE

DSR 2023 VOL-1 Factor i/c factors (DSR) (NON DSR)

Design supply & installation of suspended Spider Glazing system designed to withstand the wind pressure as per IS 875 (Part-III). The Suspended System held with

Spider Fittings of SS-316 Grade Steel of approved manufacturer with glass panel having 12 mm thick clear toughened glass held together with SS- 316 Grade

Stainless steel Spider & bolt assembly with laminated glass fins 21 mm thick. The Glass fins and glass panel assembly shall be connected to Slab/beams by means of

SS- 316 Grade stainless steel brackets & Anchor bolts and at the bottom using SS channel of 50x25x2 mm using fastener & anchor bolts, non staining weather

sealants of approved make, Teflon/ nylon bushes and separators to prevent bi-metallic contacts, all complete to perform as per specification and approved drawings.

4.11 25.8 The complete system to be designed to accommodate thermal expansion & seismic movements etc. sq m 200.00 9502.35 0.973 9245.79 1849157.31

The joints between glass panels (6 to 8 mm) and gaps at the perimeter & in U channel of the assembly to be filled with non staining weather sealant, so as to make the

entire system fully water proof & dust proof. The rate shall include all design, Engineering and shop drawing including approval from structural designer, labour, T&P,

scaffolding, other incidental charges including wastage, enabling temporary services all fitting fixers nut bolts, washer, Buffer plates, fastener, anchors, SS channel

laminated glass etc. all complete. For the purpose of payment, actual elevation area of Glazing including thickness of joints and the portion of Glass panel inside the

SS channel shall be measured.

Providing and fixing M.S. grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc. including priming coat with approved steel primer

4.12 all complete.

9.48.1 Fixed to openings /wooden frames with rawl plugs screws etc. kg 600.00 238.50 0.973 232.06 139236.30

Designing, fabricating, testing, installing and fixing in position Curtain Wall with Aluminium Composite Panel Cladding, with open grooves for linear as well as

curvilinear portions of the building , for all heights and all levels etc. including:

(a) Structural analysis & design and preparation of shop drawings for pressure equalisation orrain screen principle as required, proper drainage of water to make it

watertight including checking of all the structural and functional design.

(b) Providing, fabricating and supplying and fixing panels of aluminium composite panel cladding in pan shape in metalic colour of approved shades made out of 4 mm

thick aluminium composite panel material consisting of 3 mm thick FR grade mineral core sandwiched between two Aluminium sheets (each 0.5 mm thick). The

aluminium composite panel cladding sheet shall be coil coated, with Kynar 500 based PVDF / Lumiflon based fluoropolymer resin coating of approved colour and

shade on face# 1 and polymer (Service) coating on face# 2 as specified using stainless steel screws, nuts, bolts, washers, cleats, weather silicone sealant, backer rods

(c) The fastening brackets of Aluminium alloy 6005 T5 / MS with Hot Dip Galvanised with serrations and serrated washers to arrest the wind load movement, fasteners,

SS 316 Pins and anchor bolts of approved make in SS 316, Nylon separators to prevent bi-metallic contacts all complete required to perform as per specification and

drawing The item includes cost of all material & labour component, the cost of all mock ups at site, cost of all samples of the individual components for testing in an

approved laboratory, field tests on the assembled working curtain wall with aluminium composite panel cladding, cleaning and protection of the curtain wall with

aluminium composite panel cladding till the handing over of the building for occupation. Base frame work for ACP cladding is payable under the relevant aluminium sq m 250.00 5015.05 0.973 4879.64 1219910.91

items. The Contractor shall provide curtain wall with aluminium composite panel cladding, having all the performance characteristics all complete , as per the

Architectural drawings, as per item description, as specified, as per the approved shop drawings and as directed by the Engineer-in-Charge. However, for the purpose

of payment, only the actual area on the external face of the curtain wall with Aluminum Composite Panel Cladding (including width of groove) shall be measured in

sqm. up to two decimal places.

Providing of 120 min Fire rated doors system duly tested for 3 criteria - Integrity, Insulation and Stability Criteria as per the IS: 3614 Part 2 and BS: 476 part 22 at

National Test House, Govt of India laborator and/or with Central Building Research Institute, Govt of India undertaking with standard heating conditions as specified in

IS:3614 Part II 1992 and BS: 476 part 20 & 22 1987 to achieve the required integrity, insulation and stability (i.e. to restrict the heat radiation, temperature rise on the

non fire side to the maximum of 140° C above the ambient temperature on the exposed surface of the shutter. The fire doors are tested with NCBN technology ("Non

Combustible by Nature").

Door Frame: Providing 1st class Malaysian Hardwood Frame densified and pressure treated with fire retardant chemicals in vacuum impregnation vessel under 160

PSI pressure as per IS:401and kiln seasoned to moisture below 15% as per IS:1141 of section 120 X 70 mm spray quoted with 2 coats of In tumescent paint of

minimum 300 micron, with 1 row of Brush- Type Astroflame® intumescent strip (imported) of size 10mmx4mm concealed in the groove of the Frame for fire and smoke

Shutter: Providing of 55mm thick asbestos free composite - 3 criteria - fire, heat and smoke check Door Shutter with flame guard of 120 minutes IS3614 part -II

comprising of 2x8mm Calcium Silicate boards, Chemical treated internal timber with Fire retardant chemicals in pressure impregnation vessels under 160 PSI pressure

as per IS:401and kiln seasoned to moisture below 15% as per IS:1141 frame work of 100x32 mm with 32mm thick infill of ceramic fiber, vermaculite mix faced with

3mm Fire retardant High Density Fibreboard, internally lipped with hardwood beading, and pasted in Hydraulic Press under 50 tonnes pressure, spray quoted with 2

coats of In tumescent paint of minimum 300 micron, and with 1 row of Brush- Type Astroflame® intumescent strip (imported) of size 10mmx4mm concealed for fire

and smoke sealing in the grooves in the shutter on all edges except bottom, without any external lipping.

Vision Panel: 2 HR rated E Class clear high stress fire rated glass is pre fabricated strategically inside the shutter structure with 12 mm inside the shutter on all sides

with U- glazing. An additional insulated powdercoated 'Z' channel of 16 swg MS sheet to be fixed for reinforcement of the joints.

Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15° landings, balconies, shelves, chajjas,lintels, bands, plain window sills,

4.15 5.3 staircases and spiral stair cases above plinth level up to floor five level, excluding the cost of centering, shuttering, finishing and reinforcement with 1:1.5:3 (1 cement: Cum 300.00 11505.50 0.973 11194.85 3,358,455.45

1.5 coarse sand(zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources).

Providing and laying Vitrified tiles in floor in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to

1S:15622, of approved brand & manufacturer, in all colours and shade, laid on 20 mm thick cement mortar 1:4 (1 cement: 4 coarse sand) jointing with grey cement

4.16 11.41A slurry @3.3 kg/sqm including grouting the joints with white cement and matching pigments etc. The tiles must be cut with the zero chipping diamond cutter only . Laying

of tiles will be done with the notch trowel, plier, wedge, clips of required thickness, leveling system and rubber mallet for placing the tiles gently and easily.

11.41A.3 Glazed Vitrified tiles Matt/ Antiskid finish of size

TOTAL MISCELLANEOUS WORKS 14,040,963.48 136,800.00

Grand Total (DSR + Non-DSR/MR) 104,497,899.75

Grand Total (DSR + Non-DSR/MR) 104,497,899.75

6 Digitally signed by ASHWANI

SCHEDULE OF QUANTITIES: INTERNAL & EXTERNAL PLUMBING

S NO DSR/ MR DESCRIPTION UNIT QTY RATE AMOUNT (Rs.)

Factor i/c factors

DSR 2023 (DSR) (NON DSR)

Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including

jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion,

(i) Single socketed pipes.

a MR 160 mm diameter Metre 204 754.80 153979.20

Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain

2 12.42 water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm

gap for thermal expansion.

a 12.42.2 Single pushfit Coupler

b 12.42.3 Single tee with door

d 12.42.6 Shoe (Plain)

Providing and fixing unplasticised -PVC pipe clips of approved design to unplasticised - PVC rain water pipes by means

of 50x50x50 mm hard wood plugs, screwed with M.S. screws of required length, including cutting brick work and fixing in

cement mortar 1:4 (1 cement : 4 coarse sand) and making good the wall etc. complete.

Providing and fixing to the inlet mouth of rain water pipe cast iron grating 15 cm diameter and weighing not less than 440

5 13.7 12 mm cement plaster finished with a floating coat of neat cement of mix :

Providing and fixing floor mounted, white vitreous china single piece, double traps syphonic water closet of approved

brand/make, shape, size and pattern including integrated white vitreous china cistern of capacity 10 litres with dual

6 17.81 flushing system, including all fittings and fixtures with seat cover, cistern fittings, nuts, bolts and gasket etc including Each 84 18212.90 0.973 17721.15 1488576.74

making connection with the existing P/S trap, complete in all respect as per directions of Engineer-in-Charge.

Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard

7 17.7 pattern, including painting of fittings and brackets, cutting and making good the walls wherever require:

a 17.7.4 White Vitreous China Flat back wash basin size 550x 400 mm with single 15 mm C.P. brass pillar tap Each 84 1879.20 0.973 1828.46 153590.77

Providing and fixing wash basin with C.I. brackets, 15 mm dia CP Brass single hole basin mixer of approved quality and

8 17.7A make, including painting of fittings and brackets, cutting and making good the walls wherever required:

a a) White Vitreous China Wash basin size 550x400 mm with a 15 mm CP Brass single hole basin mixer Each 12 3960.55 0.973 3853.62 46243.38

1 Digitally signed by ASHWANI

S NO DSR/ MR DESCRIPTION UNIT QTY RATE AMOUNT (Rs.)

Factor i/c factors

DSR 2023 (DSR) (NON DSR)

Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per IS:13983 with C.I. brackets and stainless steel

17.10 plug 40 mm, including painting of fittings and brackets, cutting and making good the walls wherever required:

17.10.1 Kitchen sink with drain board

Providing and fixing CP Brass 32mm size Bottle Trap of approved quality & make and as per the direction of Engineer-

Providing and fixing CP Brass Single lever telephonic wall mixer of quality & make as approved by Engineer in charge.

Providing and fixing white vitreous china battery based infrared sensor operated urinal of approx. size 610 x 390 x 370

mm having pre & post flushing with water (250 ml & 500 ml consumption), having water inlet from back side, including

fixing to wall with suitable brackets all as per manufacturers specification and direction of Engineer-in-charge.

13 17.28 Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete.

17.28.2 Flexible pipe

Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6mm thick

hard board ground fixed to wooden cleats with C.P. brass screws and washers complete.

17.34 Providing and fixing toilet paper holder :

Providing and fixing 600x120x5 mm glass shelf with edges round off, supported on anodised aluminium angle frame with

16 17.33 C.P. brass brackets and guard rail complete fixed with 40 mm long screws, rawl plugs etc., complete. Each 95 1083.50 0.973 1054.25 100153.32

Providing and fixing M.S. holder bat clamp of approved design to sand cast iron/ cast iron (spun) pipes comprising of

M.S. flat brackets made of 50x5 mm flat of specified shape, projecting 75 mm outside the wall surface and fixed on wall

with 4nos, 6mm dia expansion hold fasteners, including drilling necessary holes in brick wall/ CC/ RCC surface and the

17.77 cost of bolts etc. The pipes shall be fixed to the already fixed brackets with the help of 30 mm x1.6 mm galvanised M.S.

flats of specified shape and of total length 420 mm and shall be fixed with M.S. nuts, bolts, & washers of size 25x6 mm,

one bolts on each side of the pipe.

17.77.3 Total bracket length 1040 mm of approved shape and design (for three 100 mm dia pipes) Each 108 451.90 0.973 439.70 47487.46

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply,

including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes

jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer

Internal work - Exposed on wall

2 Digitally signed by ASHWANI

S NO DSR/ MR DESCRIPTION UNIT QTY RATE AMOUNT (Rs.)

Factor i/c factors

DSR 2023 (DSR) (NON DSR)

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply,

including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing

19 18.8 of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same

including testing of joints complete as per direction of Engineer in Charge.

Concealed work, including cutting chases and making good the walls etc.

20 18.12 Providing and fixing G.I. pipes complete with G.I. fittings including trenching and refilling etc.

a) 18.12.5 40 mm dia nominal dia Pipes Metre 50 617.05 0.973 600.39 30019.48

b) 18.12.6 50 mm dia nominal dia Pipes Metre 50 762.15 0.973 741.57 37078.60

Making connection of G.I. distribution branch with G.I. main of following sizes by providing and fixing tee, including

18.13 cutting and threading the pipe etc. complete :

18.21 Providing and fixing uplasticised PVC connection pipe with brass unions

22 18.21.2 45 cm length

18.22 Providing and fixing C.P. brass shower rose with 15 or 20 mm inlet :

Providing and laying S&S centrifugally cast (spun) iron pipes (Class LA) conforming to IS - 1536 : vent pipes of Under

24 18.27 ground tank complete.

(Tank Vent Pipe)

25 18.40 Painting G.I. pipes and fittings with two coats of anti-corrosive bitumastic paint of approved quality :

26 18.41 Providing and filling sand of grading zone V or coarser grade, allround the G.I. pipes in external work :

Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and

27 18.48 suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the per litre 15000 11.00 0.973 10.70 160545.00

base support for tank.

Providing and fixing C.P. brass long body bib cock of approved quality conforming to IS standards and weighing not less

28 than 690 gms.

Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:8931

3 Digitally signed by ASHWANI

S NO DSR/ MR DESCRIPTION UNIT QTY RATE AMOUNT (Rs.)

Factor i/c factors

DSR 2023 (DSR) (NON DSR)

Providing and fixing C.P. Brass extension nipple (size 15mmx50mm) of approved make and quality as per direction of

Providing and fixing PTMT Ball cock of approved quality, colour and make complete with Epoxy coated aluminium rod

31 18.62 with L.P./ H.P.H.D. plastic ball.

a) 18.62.4 40 mm nominal bore, 206 mm long, weighing not less than 690 gms Each 1 737.20 0.973 717.30 717.30

b) 18.62.5 50 mm nominal bore, 242 mm long, weighing not less than 1240 gms Each 1 1375.95 0.973 1338.80 1338.80

Cutting holes up to 15x15 cm in R.C.C. floors and roofs for passing drain pipe etc. and repairing the hole after insertion

32 18.77 of drain pipe etc. with cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal Each 155.00 452.00 0.973 439.80 68168.38

size), including finishing complete so as to make it leak proof.

Providing and laying cement concrete 1:5:10 (1 cement : 5 coarse sand : 10 graded stone aggregate 40 mm nominal

size) up to haunches of S.W. pipes including bed concrete as per standard design :

Providing and fixing CP Brass liquid soap container of standard shape with bracket of the same materials with snap

34 MR fittings of approved quality and colour. Each 63 1565.00 98595.00

35 MR Providing and fixing CP Brass towel ring with concealed fittings arrangement of approved quality and colour. Each 63 2207.00 139041.00

36 MR Providing and fixing CP Brass Coat Hook of approved quality and colour Each 89 683.00 60787.00

Providing, Fixing of straight/ offset type flexible single body push fit type WC pan connector of with integral single mould

37 MR sealing fins made of flexible EVA body to be fixed with manufacture supplied grease, including rubber bush/ adaptor for Each 89 1008.00 89712.00

use with PP pipe as supplied with the pan connector.

38 MR Providing and fixing C.P. brass Two way bib cock of approved quality conforming to IS:8931. Each 81 1699.00 137619.00

Providing and fixing CP Health faucet to european type W.C. of approved quality and make as approved by engineer in

Providing and fixing CP Brass Single lever mixer for sink of quality & make as approved by Engineer in charge. (a) 15

40 MR mm nominal dia. Each 5 4338.00 21690.00

Providing and fixing CP Brass towel rail complete with brackets with CP brass screws with concealed fittings

41 MR arrangement of approved quality and colour. Each 21 3497.00 73437.00

Providing and fixing CP Brass soap Dish Holder with concealed fitting arrangements, of approved quality and colour

Providing and fixing handicap grab bar complete as per manufacture's specifications and direction of Engineer-In-

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply,

including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes

Based on jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer

DSR No in Charge.

18.7 Internal work - Exposed on wall

a) 65 mm nominal dia Pipes metre 150 1789.30 268395.00

b) 80 mm nominal dia Pipes metre 150 2281.30 342195.00

4 Digitally signed by ASHWANI

S NO DSR/ MR DESCRIPTION UNIT QTY RATE AMOUNT (Rs.)

Factor i/c factors

DSR 2023 (DSR) (NON DSR)

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply,

including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing

45 of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same

including testing of joints complete as per direction of Engineer in Charge.

Concealed work, including cutting chases and making good the walls etc.

a) 40 mm nominal dia Pipes metre 77 906.30 69785.10

b) 50 mm nominal dia Pipes metre 50 1221.10 61055.00

Providing and fixing Forged Brass Ball Valve (Screwed). with setting and gland of superior quality having minimum

working pressure of 10 kg/cm2.

Providing & fixing Auto Air vent for cold water supply risers, suitable for pressure not less than 15 Kg/Sq.cm.

Providing, fixing & testing uPVC SWR pipes confirming to IS 13592 (Type B) alongwith all required fittings like tees,

bends, crosses with or without access doors jointed with approved solvent cement as per manufacturer's

MR recommendations, fixed to walls and ceilings with clamps complete including cutting and making good the floors and

walls where required complete of outer diameter.

Providing, fixing, jointing and testing in position the following uPVC pipes conforming to IS 4985 of 6 kg/sqcm pressure

rating including all fittings, solvent weld joints, testing complete for drainage system cut to required length to be laid

under floor including covering all around with cement concrete and making good the same complete as required.

MR For waste pipes

a) 63mm OD (6 kg pressure) Metre 163 1134.00 184842.00

b) 50mm OD (6 kg pressure) Metre 92 837.00 77004.00

c) 40mm OD (6 kg pressure) Metre 176 634.00 111584.00

Providing and Fixing 110x110 mm uPVC 'P' trap with Height riser/Saddle as required size ftting with seal 50 mm of

49 self cleansing design floor/urinal trap without vent suspended with supporting clamp or in sunken portion including cutting

MR and making good the walls and floors wherever required complete in all respects.

a) 110 mm inlet & 110 mm outlet Each 130 600.00 78000.00

Providing and Fixing uPVC floor drain of following size inlet and outlet including cutting and making good the walls and

50 floors wherever required complete in all respects. Each 58 192.00 11136.00

a) 110x63mm outlet

Providing & fixing uPVC clean out plug with suitable insert keys for opening in: brass cap, male threaded joint with

MR threaded uPVC socket fixed to uPVC pipe joints as required complete in all respects.

Providing and fixing rectangular shape Stainless steel grating with frame for floor traps or drains of required pattern

52 MR including cutting and making good the floors complete. Each 188 955.00 179540.00

5 Digitally signed by ASHWANI

S NO DSR/ MR DESCRIPTION UNIT QTY RATE AMOUNT (Rs.)

Factor i/c factors

DSR 2023 (DSR) (NON DSR)

Supply, installtion, testing and commissioning of WC pan connector with factory supplied spring loaded seal guard of

53 MR with integral single mould sealing fins made of flexible EVA body, including bush/adaptor for use with uPVC Pipe as Each 85 251.00 21335.00

supplied with the pan connector (if required).

Supplying and laying of following size DWC SN8 pipe ISI marked along with all accessories like socket, bend, couplers

etc. conforming to IS 16098, Part II complete with fitting and cutting,jointing etc.direct in ground (75 cm below ground

level) including excavation and refilling the trench but excluding sand cushioning and protective covering etc., complete

Supply installation, testing and commissioning of water cooler with Inbuilt RO purification+UV(50LPH) .Cooling capacity

shall be 60Litre and storage capacity shall be 80Litre. Its should have 7 stages purification process,fully

automatic,rectangular tank with Forced fin and tube condenser,Non-corrosive SS-304 outer body,Food-grade SS-304

stainless steel inner tank (18/8 or 18/10),PUF insulation,Reciprocating compressor with R22 Refrigerant.Water outlet

temp is aprrox 17 deg C, Operating power supply 230+10% V AC, 50 Hz, 1 PH, No of Cold water Faucet-2.

Supply, Installation, testing and commissioning of storage type electric hot water heater made out of heavy gauge steel

jacket finished with rust proof baked-on glossy white enamel paint, inside glass lined heavy gauge steel tank, 25 mm

thick polyurethane foam insulation, thermostatically controlled immersion heater with pilot neon lamp, replaceable

magnesium anode bar, suitable for 8.0 bar maximum working pressure, cold water inlet and hot water outlet pipe,

suitable length of electrical cable and 15 amp 3 pin plug top, complete in all respect including testing etc.

Supply, Installation, Testing and Commisioning of Vessel type TABLE TOP BASIN having minimum SIZE:

630x460x130mm thinner edges and rimless bowl as per the color choice of the engineer in charge

Supply, Installation, Testing and Commisiong of smart WC having Rimless bowl and Advanced bidet functionality with

58 MR massaging jets,Self-cleaning nozzle for improved hygiene,Heated seat for added comfort,Touchless control for easy Each 4 60865.00 243460.00

adjustments,Auto-Open and Auto closed seat.

Supply, Installation, Testing and Commisiong of PNEUMATIC SINGLE PIECE SLIM CONCEALED CISTERN BODY

59 MR WITH INSTALLATION KIT & “S-TYPE” DRAIN PIPE CONNECTION SET FOR WALL HUNG WC (WITHOUT FLUSH Each 4 8044.00 32176.00

Supply, Installation, Testing and Commisioning of SINGLE LEVER CONCEALED BASIN MIXER (WALL MOUNTED)

WITH SPOUT (COMPOSITE ONE PIECE BODY)

TOTAL OF PLUMBING WORKS 4732590.95 4706997.30

Grand Total (DSR + Non-DSR/MR) 9439588.25

Grand Total (DSR + Non-DSR/MR) 9439588.25

6 Digitally signed by ASHWANI

SCHEDULE OF QUANTITIES - ELECTRICAL WORKS

DSR NO DSR Rates i/c AMOUNT (RS.)

S NO DESCRIPTION UNIT QTY RATE GST Factor Cess Factor

2022 Factors DSR (INR) NON-DSR (INR)

Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface /

1 1.10 recessed medium class PVC conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm. FRLS PVC insulated

copper conductor single core cable etc as required.

Wiring for group controlled (looped) light point/ fan point/call bell point (without independent switch etc.) with 1.5 sq.mm FRLS PVC insulated copper

2 1.55 conductor single core cable in surface/ recessed PVC conduit, and earthing the point with 1.5 sq.mm. FRLS PVC insulated copper conductor single core

cable etc as required.

Wiring for light/ power plug with 2X4 sq. mm FRLS PVC insulated copper conductor single core cable in surface/ recessed medium class PVC conduit

alongwith 1 No 4 sq. mm FRLS PVC insulated copper conductor single core cable for loop earthing as required.

Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc.

4 1.24 as required.

Supplying and fixing two module stepped type electronic fan regulator on the existing modular plate switch box including connections but excluding

modular plate etc. as required.

5 1.27 Supplying and fixing following size/module, GI box along with Modular base & cover plate on existing modular metal boxes etc. as required.

6 LIGHT & POWER PLUGS

Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 3 pin 5/6 A modular

socket outlet and 5/6 A modular switch, connections etc. as required.

Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 6 pin 5/6 & 15/16 A

modular socket outlet and 15/16 A modular switch, connections etc. as required.

Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providng and fixing 2 nos. 3 pin 5/6 A

6.3 1.56 modular socket outlet and 2 nos. 5/6 Amp modular switch, connections etc. as required. (For light plugs to be used in non residential buildings). Each 550 676.00 1.0633 0.973 699.38 384660.90

SUBMAIN AND CONTROL WIRING

Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FR PVC insulated copper conductor, single core cable in surface/

recessed medium class PVC conduit as required

SUPPLY OF LT CABLES

8 Supply of following XPLE armourned 1.1 KV grade conforming to I.S.7098/1554Aluminium Conductor Cables :

Supply of following sizes of PVC sheathed XLPE insulated Aluminium conductor armoured cable of 1.1 KV grade conforming to IS:7098 part-1 / IS:1554

part-1 respectively & ISI marked.

8.2 MR 3.5 C x 50 Sqmm XLPE cable 510.00 76,500.00

Supply of following sizes of copper cables -PVC sheathed XLPE insulated Copper conductor armoured cable of 1.1 KV grade conforming to IS:7098 part-

1 / IS:1554 part-1 respectively & ISI marked.

8.1 2 C x 10 Sqmm XLPE copper cable RM 500 450.00 225,000.00

8.2 MR 4 C x 6 Sqmm XLPE copper cable RM 840 556.00 467,040.00

8.3 4 C x 10 Sqmm XLPE copper cable RM 1450 885.00 1,283,250.00

8.4 4 C x 16 Sqmm XLPE copper cable RM 1200 1446.00 1,735,200.00

8.5 4 C x 25 Sqmm XLPE copper cable RM 800 2253.00 1,802,400.00

LAYING OF LT CABLES

Laying and fixing of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size on cable tray as required.

9.1 7.8.1 Upto 35 sq. mm (clamped with 1mm thick saddle) RM 5038 45.00 1.0633 0.973 46.56 234552.10

9.2 7.8.2 Above 35 sq. mm and upto 95 sq. mm (clamped with 25x3mm MS flat clamp) RM 375 92.00 1.0633 0.973 95.18 35693.39

9.3 7.8.3 Above 95 sq. mm and upto 185 sq. mm (clamped with 25/40x3mm MS flat clamp) RM 125 115.00 1.0633 0.973 118.98 14872.24

9.4 7.8.4 Above 185 sq. mm and upto 400 sq. mm (clamped with 40x3mm MS flat clamp) RM 50 185.00 1.0633 0.973 191.40 9569.97

1 Digitally signed by ASHWANI

DSR NO DSR Rates i/c AMOUNT (RS.)

S NO DESCRIPTION UNIT QTY RATE GST Factor Cess Factor

2022 Factors DSR (INR) NON-DSR (INR)

CABLE END TERMINATIONS

Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE

aluminium conductor cable of 1.1 KV grade as required.

Supplying and fixing 5 amps to 32 amps rating, 240/415 volts, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the

existing MCB DB complete with connections, testing and commissioning etc. as required.

Supplying and fixing following rating, four pole, 415 volts, TPN MCB in the existing MCB DB complete with connections, testing and commissioning etc.

Supplying and fixing following way, horizontal type three pole and neutral, sheet steel, MCB distribution board, 415 V, on surface/ recess, complete with

14 2.4 tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/

RCCB/ Isolator)

Supplying and fixing following way, single pole and neutral, sheet steel, MCB distribution board, 240 V, on surface/ recess, complete with tinned copper

15 2.3 bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator)

16 PROVISIONS FOR VOICE, DATA, SECURITY & TV SYSTEMS

16.1 MR Supply, installation, testing & Commissioning of 1 module 16A SWITCH SP 1 way for floor box. Set 5 216.00 1,080.00

16.2 MR Supply, installation, testing & Commissioning of 2 module 16 A Socket for floor box . Set 5 577.00 2,885.00

Supply, installation, testing & Commissioning of Specific Backbox for Carpet for Floor Box along with LID and TRIM for tiles/ marble 15 to 20mm

16.3 MR thickness material for headband and single cable outlet/ glavanized steel, paint RAL 7031 for floor box . Set 7 12106.00 84,742.00

Supply, installation, testing & Commissioning of Specific Backbox for Wooden Flooring for Floor Box along with LID and TRIM for tiles/ marble 15 to

20mm thickness material for headband and single cable outlet/ glavanized steel, paint RAL 7031 for floor box.

16.5 MR Supply, installation, testing & Commissioning of flat support plate 8 module for integration of Mechanism for Floor Box Set 5 263.00 1,315.00

16.6 MR Supply, installation, testing & Commissioning of waved support plates for 4 module (2x2) modules for Floor Box Set 5 1533.00 7,665.00

Supply, Installation, Testing and Commisioning of Galavanized Iron (GI) Raceways 2mm thick along with required suitable number of GI couplers for

joining raceways and fixing GI brackets and all accessories complete in all respect as per the directions of engineer in charge

17.1 300mmx38mm(GI) - 3 compartment Mtr 250 1738.00 434,500.00

17.2 225mmx38mm(GI) - 3 compartment Mtr 175 1420.00 248,500.00

MR 150mmx38mm(GI)

Supply, Installation, Testing and Commisioning of Junction boxes for direct access to cables at the intersection of raceways supplied completely with

18 base and cover plates, height adjustable junction box 65- 90 mm including all accessories ss plate of 3mm thick complete in all respect as per the

directions of engineer in charge

Supplying and fixing of following sizes medium class PVC conduit aong with accessories in surface/ recess including cutting the wall and making good

the same incase of recessed conduit as required

2 Digitally signed by ASHWANI

DSR NO DSR Rates i/c AMOUNT (RS.)

S NO DESCRIPTION UNIT QTY RATE GST Factor Cess Factor

2022 Factors DSR (INR) NON-DSR (INR)

Supplying and installing following size of perforated Hot Dipped Galvanised Iron cable tray (Galvanisation thickness not less than 50 microns) with

20 4.6 perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with G.I. suspenders including G.I. bolts &

nuts, etc. as required.

Earthing with copper earth plate 600 mm X 600 mm X 3 mm thick including accessories, and providing masonry enclosure with cover plate having

21.1 5.6 locking arrangement and watering pipe of 2.7 metre long etc. with charcoal/ coke and salt as required. SET 10 13838.00 1.0633 0.973 14316.67 143166.69

21.2 5.14 Providing and fixing 25 mm X 5 mm copper strip on surface or in recess for connections etc. as required. MTR 1500 1162.00 1.0633 0.973 1202.19 1803291.94

21.3 5.15 Providing and fixing 25 mm X 5 mm G.I. strip on surface or in recess for connections etc. as required. MTR 1500 244.00 1.0633 0.973 252.44 378660.27

21.4 5.16 Providing and fixing 6 SWG dia G.I. wire on surface or in recess for loop earthing as required. MTR 2000 70.00 1.0633 0.973 72.42 144842.73

22 PANEL BOARDS

Supplying, installing, testing & commissioning of following type compartmentalised wall mounted / floor mounted cubicle board made from 2mm thick

CRCA sheet dust & vermin proof duly phosphatized & powder coated inclusive of suitable size 4 strip Al. Busbar complete with interconnection providing

Lugs, inter-earthing, painting etc. i/c providing & fixing below noted accessories:

Receiving,unloading,storing, handling, installation, testing and commissioning of following MV Switchboards complete as required and as per site

condition and dimension of all panels shall be carried out as per the attachad sld

22.1 MR FLOOR PANELS (GROUND & FIRST FLOOR) Set 2 350000.00 700,000.00

Incomer 630A 4P MCCB - 1no

Busber - 800A Aluminium

Smart 3 phase Energy Meter for rated load, with CT of suitable ratings

R,Y,B Indication Lamp - 3nos

630A Digital Multifunction Meter - 1no

630/5A CT - 3nos

Body - 1.6mm Powder Coated.

Wall/Floor Mounted - Top & Bottom Entry

250A 4P MCCB - 2no

100A 4P MCCB - 2no

63A 4P MCB - 10nos

40A 4P MCB - 5nos

32A DP MCB - 2nos

10/16A SP MCB - 10nos

22.2 MR FLOOR PANELS (SECOND FLOOR) Set 1 250000.00 250,000.00

Incomer 400A 4P MCCB - 1no

Busber - 500A Aluminium

Smart 3Phase Energy Meter for rated load, with CT of suitable ratings

R,Y,B Indication Lamp - 3nos

400A Digital Multifunction Meter - 1no

400/5A CT - 3nos

Body - 1.6mm Powder Coated.

Wall/Floor Mounted - Top & Bottom Entry

200A 4P MCCB - 2no

100A 4P MCCB - 2no

63A 4P MCB - 5nos

40A 4P MCB - 5nos

32A DP MCB - 2nos

10/16A SP MCB - 10nos

Distribution Panel Wall/ Floor Mount AS PER SINGLE LINE DIAGRAM

Incomer - 250A 4P MCCB - 1no

Busber - 320A Aluminium

R,Y,B Indication Lamp - 3nos

250A Digital Multifunction Meter - 1no

250/5A CT - 3nos

Body - 1.6mm Powder Coated.

Wall/Floor Mounted - Top & Bottom Entry

100A 4P MCCB - 2no

63A 4P MCB - 5nos

40A 4P MCB - 4nos.

32A DP MCB - 2nos.

10/16A SP MCB - 10nos

22.4 MR UPS Output Panel Set 4 115000.00 460,000.00

3 Digitally signed by ASHWANI

DSR NO DSR Rates i/c AMOUNT (RS.)

S NO DESCRIPTION UNIT QTY RATE GST Factor Cess Factor

2022 Factors DSR (INR) NON-DSR (INR)

Distribution Panel Wall/ Floor Mount AS PER SINGLE LINE DIAGRAM

Incomer - 100A 4P MCCB - 1no

Busber - 150A Aluminium

R,Y,B Indication Lamp - 3nos

100A Digital Multifunction Meter - 1no

100/5A CT - 3nos

Body - 1.6mm Powder Coated.

Wall/Floor Mounted - Top & Bottom Entry

63A 4P MCB - 2nos

40A 4P MCB - 4nos

32A DP MCB- 4nos.

10/16A SP MCB - 10nos

23 SAFETY ITEMS

Providing and fixing MV danger notice plate of 200mm x 150mm made of mild steel, atleast 2 mm thick, and vitreos enamelled white on both sides and

with iscription in single red colour on front side as required

DSR 2025 UPS SYSTEM: Online UPS- Input supply: Three Phase, Output supply: Three Phase

Supplying, installation, Testing & Commissioning of following capacity at full load (Unity Power Factor) at operating temperature 0 to 40 deg C, Relative

humidity 0 to 95%, Online double conversion true sine wave Uninterrupted hot swappable (allow for the replacement or addition of battery modules

without shutting down the entire system) modular Power Supply (UPS) system with N+1 modules (N denotes total number of moduels requird for rated

capacity). The UPS shall include a Rectifier, inverter, battery bank suitable for 30 minutes back up (Battery VAH capacity shall not be less than 1600

VAH per KVA of UPS rating per Hour backup time) on full load (Battery shall be VRLA, SMF in ABS Container) and Static Bypass switch alongwith

provision for manual bypass, suitable isolation transformer for additional protection against neutral faults etc. UPS shall have inbuilt phase sequence

correction. The UPS systems offered are to be of the latest technology with Digital Control Microprocessor based for reliable operation using Insulated

Gate Bipolar Transistor (IGBT)'s both for the rectifier & inverter (3 Level) with PWM (Pulse Width Modulation). The quality of design, manufacturing and

inspection process should confirm to the relevant Inter national standards such as IEC/EN/VDE. The operating efficiency of the UPS systems shall be

>96% while operating on battery mode and delivering quality power to the 100% non-linear loads. Current total harmonic effect(ITHD) on the input grid

shall be < 5% at 50 %load. (The required LC ( inductor (L) and a capacitor (C)) filters shall be included in UPS cost), extreme power factor kit to be

included to limit the input power factor (PF) to 0.99 and output power factor shall be unity (i.e. kw rating of the UPS shall be kva rating x 1 ), however

UPS shall be suitable to take load at 0.7 laging to 0.7 leading power factor loads. UPS shall be suitable for incoming supply AC : 3Phase 400V +/-20%,

50 Hz +/-5 Hz, AC Output voltage: 3Phase 415 Volt, 50 Hz +/- 0.2Hz, Overload capacity of 120% for 10 mins, Sine wave output. Non condensing, noise

level less than 60db at 1 meter distance, protections: Input Under voltage over voltage, abnormal out voltage, battery over charging, output over current,

short circuit protection, battery deep discharge protection, 10KV surge. UPS must comply with low voltage electromagnetic compatibility (EMC) achieved

24 5.2 as per EN 6204, EN6204 Part I and Part 2, it shall be a Voltage and Frequency Independent (VFI)-type UPS. Communication RS232/RS485/SNMP port

open protocol for BMS integration, all hardware & software for iOT Communication as per approved by Engineering in charge. Required battery racks

and interconnecting copper conductor cables of suitable size and connectors and all required accoseries are inclusive of the cost). This system must

provide a means for logging and alarming of all monitored points plus email notification. Forced air-cooling with integral inbuilt fans with redundancy (if

one fan fail UPS should be able to handle at least 80% of the load, Noise Level 65 DB at 1 meter distance. The system shall be in compliance IEC 62040-

1,2 & 3, IS: 16242 and CPWD Specification. Display Panel (minimum) (In-build 5 inch or more LC Display / LED ) to display : a) Input: Voltage, current,

Frequency. b) Bypass: Voltage, Frequency. c) Output: Voltage, frequency, Current. d) Battery: Voltage, Capacity. e) Load: KVA, KW, Percentage.

f)Temperature: STS, Inverter, PFC. g) Event Logging & Statistical Data (On LCD/LED): UPS should capture and display up to 3000 events like: Over

temperature / DC Bus Fail / Fan Fail / Fuse Fail / Overload / Short-circuit / Device Fail / Inverter Fail / Rectifier Fail / Bypass Fail, etc. h) Statistical Data:

No. of power failures / Transfers to Bypass / Total Running time, etc. i) Mains Mode of Operation /Battery Mode of Operation / Bypass feeding the load /

UPS Fault /Battery charging and discharging, overload, battery voltage and battery capacity. j) Audible Alarms : Mains Failure, Battery Low Alarm, UPS

Overload, Fault, Shutdown, Input Over, Under Voltage, Output Over, Under Voltage, Battery Over, Under Voltage, Over Load and short circuit, Over

Temperature. The UPS should have QR code which should contain drawing, test report OEM manual,Geo- Tag of manufacturing location etc.

24.1 5.2.2 20KVA (Each Power module shall be < 10 KVA) Nos. 4 341772.00 1,367,088.00

Brush Less Direct Current (BLDC) Motor Fan

Supply, Installation, Testing and Commissioning of ceiling fan with Brush Less Direct Current (BLDC) Motor, class of insulation: B, 3 nos. metal

(Aluminum alloy) blades, 30 cm long down rod, 2 nos. canopies, shackle kit, safety rope, copper winding, steel/Al body Power Factor not less than 0.9,

25 2.1 Service Value (CM/M/W) minimum as below, 350 RPM (tolerance as per IS: 374-2019), THD (Total Harmonic Distortion) less than 10%, remote

(preferably mobile app based) for speed control and all remaining accessories including safety pin, nut bolts, washers, temperature rise = 75 degree C

(max.), insulation resistance more than 2 mega ohm, suitable for 230 V, 50 Hz, single phase AC Ceiling Fan compliant to IS 374:2019 fan supply,

earthing etc. complete as required

25.1 2.1.3 1200mm, service value ≥ 6.0 CM/Min/Watt, air delivery 210 CM/Min (Minimum) Nos. 28 2381.00 66,668.00

26 MR Supplying, installation, Testing & Commissioning of 250 mm dia Domestic type Exhaust (Propeller) Fans for attached Toilets Nos. 20 2150.00 43,000.00

Total of Electrical Works 14,836,797.31 10,658,546.00

Grand Total (DSR + MR) 25495343.31

Grand Total (DSR + MR) 25495343.31

4 Digitally signed by ASHWANI

SCHEDULE OF QUANTITIES: LIGHTING FIXTURES

S No Description Ref. Images Unit Qty RATE NON-DSR

2025/MR DSR (INR)

LED Down lighter (SMD Type) (System lumen efficacy ≥ 105 < 120 lm/Watt )

Supplying, installation, Testing & Commissioning of LED Recessed/ surface Down lighter (Round/ square/ Rectangular) SMD type of following body material

with PMMA and prismatic diffuser and construction as per IS: 10322 with driver as per the requirement with Driver efficiency >85%, Operating voltage AC 140-

270 Volt, frequency 50/60 hz, Operating temp range -15 deg to 40 deg centigrade, internal surge protection of 2.5 KV with Short & Open circuit

protection ,THD < 10% , P. F.≥0.95, IP20, CRI >80 , UGR (Unified Glare Rating) < 19, Flicker free (flicker should be below 5%), life time (LED,Driver &

electrical circuitary), of minimum 50000 Burning Hours with 70% of initial Lumen maintained till life ends, CCT 3000°K / 4000°K / 5700°K /

6000°K / 6500°K (As per ANSI Bin), SDCM (Standard Deviation Color Matching) <3, Maximum power consumption should not more than the specified

1 1.1 rating and Fixture shall be confirming to relevant BIS standards and trade mark certificate (T.C.). Manufacturers Word Mark/ Name Engraved/ Embossing/

Screen printing on housing Complete in all respect i/c connections with 1.5 sq mm FRLS, PVC insulated copper conductor single core cable and

earthing etc. as required with Minimum 5 year OEM warranty. System lumen efficacy ≥105 and <120 lm/Watt output . LM79 & LM80 Test report from

NABL lab for all testing required for LED fixtures as per BIS shall be submitted. Shape size and CCT shall be as approved by Engineer-in-Charge as per

requirement. (Thermal management: heat sink of aluminum housing such that LED junction temperature shall not rise above 90°C) Powder coated die

cast /Extruded aluminum Body including trim

Supply of Integral, SMD 4x1 Backlit LED Panel, IP 20, 30W LED recessed mounted fixture with system efficacy of minimum 100lm/W and system lumen

output of minimum 3000lm, operating in ambient temperature of 0⁰C to 45⁰C at 50Hz frequency. Luminaire shall have CRCA housing coated in white

(RAL9016) with translucent HET diffuser for uniform illumination and wider light distribution. LEDs used in the product shall comply with IEC 62471. LM 80-08

compliant LEDs from reputed makes such as Nichia/Cree/ Bridgelux/ Lumiled/ Osram/Seoul should be provided. The LED shall comply with L70 life of 50000

burning hours tested at maximum current. The LEDs used should be with CCT of 4000 K and CRI of Minimum 80. LED Driver shall be Isolated type, Constant

Current topology driver with proper heat sink for heat dissipation suitable to operate in input voltage range of 140V to 300V (nominal rated voltage – 240V)

2 MR with 4KV internal surge protection, Power factor of minimum 0.95 and total harmonic distortion (THD) of less than or equal to 10% should be integral to the nos 450 3250.00 1462500.00

luminaire. Manufacturer shall have inhouse lab approved by NABL or ministry of science of govt of India. LM 79 and LM80 reports need to be submitted from

a NABL/UL accredited lab to verify above parameters. Compliance to Indian Standards of IS10322 Part 5 / Sect 5:1967; 16105 : 2012; IS 16106 : 2012; IS

Supply of 30W, suspended by 1.5m suspension wire, 4 feet linear, IP20, SMD LED luminaire with system efficacy of 110 lumen/watt and system lumen output

of 3300 lumen, operating in an ambient temperature of 0⁰C to 45⁰C. Operating at 50Hz frequency, luminaire shall have extruded aluminium housing in white

with high efficiency translucence diffuser and must have provision for end to end seamless connectivity. EMC package of wattage of 0.2-0.5 W LEDs used in

the product shall comply with IEC 62471 for Photo-biological safety. LM 80-08 compliant LEDs from reputed makes such as Nichia/Cree/ Bridgelux/ Lumiled/

Osram/Seoul should be provided. The LED shall comply with L70 life of 50000 burning hours tested at maximum current. The LEDs used should be with CCT

of 4000 K and CRI of Minimum 80, with MacAdam CCT binning ≤3 mounted on 1.6mm FR4 / MCPCB with 35 micron cu layer. LED Driver shall be Isolated

type, Constant Current topology driver with proper heat sink for heat dissipation suitable to operate in input voltage range of 140V to 300V (nominal rated

3 MR voltage – 240V) with 3KV internal surge protection, Power factor of minimum 0.95, driver efficacy of minimum 85% and total harmonic distortion (THD) of nos 112 4000.00 448000.00

less than or equal to 10% should be integral to the luminaire. Manufacturer shall have inhouse lab approved by NABL or ministry of science of govt of India.

LM 79 and LM80 reports need to be submitted from a NABL/UL accredited lab to verify above parameters. Compliance to Indian Standards of IS10322 Part

Design, manufacture, supply, installation, and commissioning of a Electronically Driven, Non Dimmable (but capable for dimming with just changing the Driver,

if required in future) customized translucent ceiling-mounted fabric and light engine. Sketch Lighting make Illuminated Ceiling, or equivalent from any

approved makes, matching below specifications. from any approved makes The light box will be installed as per the architectural requirements and must meet

the following technical specifications. The light box will be ceiling-mounted, size as approved by the architect. The ceiling box should have a uniform depth of

250 mm or as requested by the light manufacturer for spotless and glare-free illumination. Structure: The side walls of the light box will be constructed by the

GC as part of the ceiling. Wooden box which is not part of this item, should be made from 18 mm thick moisture and termite-resistant plywood or HDDMR

(High-Density High-Moisture Resistant Board), as approved by the architect. The roof of the box shall also be made of the same moisture and termite-resistant

plywood or HDDMR board.

Interior Finish: The inner side of the box shall be primed and painted in matte white for even light reflection and the white part should not be visible after

installation of the fabric. Thermal Management: Before installing the LED light engine, the interior of the light box must be equipped with Thermal Interface

Material for optimal heat dissipation. Thermally conductive metal sheets should be securely attached to the interior roof of the wooden box to further enhance

heat dissipation. LED Light Engine: The light engine must be low voltage ranging from 12- 24V. The color temperature (CCT) shall be customizable, offering

the client four options to choose one from: 3000K, 4000K, 5700K and 6500K. The lux level on the workplane should be minmum 1000 lux and it should be

4 MR compatible for dimming. The input voltage for the light engine must be 24V and should have a protection rating of IP20. All LED drivers should be installed SQM 200 6000.00 1200000.00

outside of the light box, in an easily accessible location for maintenance purposes. Diffuser: A jointless translucent diffuser made from polyester knitted fabric

coated with polyurethane (PU) must be installed inside the ceiling box, approximately 20-30 mm up from the bottom edge of the structure. The remaining 20-

30 mm exposed surface outside the diffuser should be finished to match the color of the wooden ceiling surface and edges. The diffuser fabric should be:

Heavy-duty, with a minimum weight of 200 gm/m² and a minimum thickness of 0.3 mm. Matte, smooth, and uniform in appearance to reduce glare and

provide a soft ambient glow even at higher lux levels. It should have a light transmission efficiency of 50-60%, ensuring low-glare, soothing ambient lighting.

The diffuser must meet the following technical specifications: Tear strength: CH: 4.5 daN; TR: 6.5 daN Fire rating: B-S1, d0 Humidity-resistant and free from

harmful CMR (Carcinogenic, Mutagenic, Reprotoxic) substances and VOC (Volatile Organic Compounds).Installation Requirements Mounting and Integration:

The light engine should be securely mounted to the ceiling wooden boxes, maintaining the required depth and alignment. Wood work not included.

TOTAL (DSR + Non-DSR) 4314427.00

Public Digitally signed by ASHWANI

SCHEDULE OF QUANTITIES: HVAC

S No Description Unit Qty RATE

DSR (INR) NON-DSR (INR)

VRF OUTDOOR UNIT: Supply, Installation, Testing & Commissioning of Modular type Variable Refrigerant

Flow/Variable Refrigerant Volume air cooled Outdoor units suitable for cooling/heating having 100% hermetically

sealed inverter type twin Rotary/Scroll Compressor(s), minimum two compressors (with individual seperate PCB)

for above 14HP modules, microprocessor based Controller, top discharge type condensing unit(s), with R-410-A

Refrigerant or equivalent, vibration Isolators with suitable foundation etc. complete as required. To have better

efficiency condensor fan shall be capable to operate at different speed with respect to load. The unit shall deliver

the rated capacity and in confirmation as per IS 18728:2024 and CPWD Specifications and work even at 50°C

ambient temperature without tripping. The system shall be able to deliver 100% of the rated capacity upto 39

Degree Celcius. The unit shall be suitable to work on 400V +/- 10%, 3 Phase, 50Hz AC power supply and BMS

1 7.1 compatible. The unit shall be filled with first charge of the refrigerant and ready for use as required. The condenser

should be coated with a hydrophilic film to prevent water accumulation on the surface of the heat exchanger,

enhance water dispersion, and reduce the risk of degradation, thereby improving overall performance and

durability. The Indian Seasonal Energy Efficiency Ratio (ISEER) of the unit shall be as per Energy Conservation

and Sustainable Building Code (ECSBC) 2024 as below and complete as per CPWD specification, connections,

inter connections etc. as required. (For capacity <40 kWr ISEER 5.4, Capacity > 40 and <70 ISEER 5.5, Capacity >

70 ISEER 5.6 for ECSBC Building)

For Cooling or Heating or Both

VRF INDOOR UNITS: Supply, Installation, Testing and Commissioning of following minimum capacity High wall

type Indoor unit equipped with and comfort washable synthetic media pre-filter, fan section with low noise

fan/dynamically balanced blower, multispeed motor, coil section with DX copper coil, electronic expansion valve,

outer cabinet, cord less remote control, drain pan & drain pump, necessary accessories etc., suitable for operation

2 7.8 on 230 V ± 10%, 50 Hz, single phase AC supply, complete as required. The Indoor units must shut down upon

receiving a singal from the BMS System/Fire Singnals. The system shall be capable to adjust air flow as per room

requirement automatically. The cooling capacity of indoor unit will be at air inlet conditions of 27 Degree C DB and

19 Degree C WB temperature. (Make will be same as of Outdoor)

Supply, Installation, Testing and Commissioning of following minimum capacity 4-way compact VRV/VRF Cassette

Type Indoor ceiling mounted unit equipped with synthetic washable media pre-filter, fan section with low noise

fan/dynamically balanced blower, multispeed motor, coil section with DX Copper coil, electronic expansion valve,

outer cabinet, drain pump, grill, necessary supports, vibration Isolation, Corded remote control etc., suitable for

3 7.5 operation on single phase 230 V ± 10%, 50Hz AC supply, complete, as required. The Indoor units must shut down

upon receiving a signal from the BMS System/Fire Signals. The system shall be capable to adjust air flow as per

room requirement automatically. The cooling capacity of indoor unit will be at air inlet conditions of 27 Degree C DB

and 19 Degree C WB temperature. (Make will be same as of Outdoor)

1 Digitally signed by ASHWANI

S No Description Unit Qty RATE

DSR (INR) NON-DSR (INR)

INDOOR UNIT Supply, Installation, Testing and Commissioning of following minimum capacity 4 way Cassette

Type Indoor ceiling mounted unit equipped with synthetic washable media pre-filter, fan section with low noise fan /

dynamically balanced blower, multispeed motor, coil section with DX Copper coil, electronic expansion valve, outer

cabinet, drain pump, grill, necessary supports, vibration Isolation, Corded remote control etc., suitable for

4 7.4 operation on single phase 230 V ± 10%, 50Hz AC supply, complete, as required. The Indoor units must shut down

upon receiving a singal from the BMS System/Fire Signals. The system shall be capable to adjust air flow as per

room requirement in auto mode. The cooling capacity of indoor unit will be at air inlet conditions of 27 Degree C

DB and 19 Degree C WB temperature. (Make will be same as of Outdoor)

Supply, Installation, Testing and Commissioning of following minimum capacity and external static pressure

VRF/VRV ceiling mounted high ductable type Indoor unit equipped with washable synthetic media pre-filter, fan

section with low noise fan/dynamically balanced blower, multispeed motor, coil section with DX copper coil,

electronic expansion valve, corded remote control, outer cabinet, vibration Isolators, drain pan, drain pump, other

5 7.12 necessary supports etc., suitable for operation on single phase AC supply 230 V ± 10%, 50 Hz complete as

required. The Indoor units must shut down upon receiving a singal from the BMS System/Fire Signals. The cooling

capacity of indoor unit will be at air inlet conditions of 27 Degree C DB and 19 Degree C WB temperature. (Make

will be same as of Outdoor)

Supply, Installation, Testing and Commissioning of Y/T/Multi Joints. Joints shall be of same Original Equipment

Manufacturer (OEM) make as of ODUs and IDUs

b 7.13.2 Outdoor Multi Joint Nos 28 8,098.00 226,744.00

REFRIGERANT PIPING:

Supply, Installation, testing and commissioning including vaccumiazation and Nitrogen testing of following nominal

sizes of soft/hard drawn copper refrigerant piping for VRV/VRF system, complete with fittings, with suitable

adjustable ring type hanger supports, jointing/brazing including accessories, insulated with XPLE Class-O tubular

insulation/with Class-O closed cell elastometric nitrile rubber tubular sleeves sections of 19 mm thick insulation as

given below for Suction and Liquid lines, all accessories as per specifications etc. as required:

a 7.14.1 6.4 mm dia (OD) (Soft drawn) with tube thickness 1.2 mm Metre 626 256.00 160,163.87

b 7.14.2 9.5 mm dia (OD) (Soft drawn) with tube thickness 1.2 mm Metre 927 346.00 320,749.04

c 7.14.3 12.7 mm dia (OD) (Soft drawn) with tube thickness 1.2 mm Metre 915 487.00 445,695.60

d 7.14.4 15.86 mm dia (OD) (Soft drawn) with tube thickness 1.2 mm Metre 889 615.00 546,827.61

e 7.14.5 19 mm dia (OD) (Hard drawn) with tube thickness 1.2 mm Metre 777 739.00 574,291.08

f 7.14.6 22.2 mm dia (OD) (Hard drawn) with tube thickness 1.2 mm Metre 1015 904.00 917,193.67

g 7.14.7 25.4 mm dia (OD) (Hard drawn) with tube thickness 1.2 mm Metre 68 1,068.00 72,463.80

h 7.14.8 28.58 mm dia (OD) (Hard drawn) with tube thickness 1.2 mm Metre 268 1,157.00 310,358.52

i 7.14.9 31.8 mm dia (OD) (Hard drawn) with tube thickness 1.62 mm Metre 178 1,222.00 216,922.76

j 7.14.10 34.9 mm dia (OD) (Hard drawn) with tube thickness 1.62 mm Metre 319 1,286.00 409,896.05

2 Digitally signed by ASHWANI

S No Description Unit Qty RATE

DSR (INR) NON-DSR (INR)

k 7.14.11 38.1 mm dia (OD) (Hard drawn) with tube thickness 1.62 mm Metre 126 1,322.00 166,879.44

l 7.14.12 41.27 mm dia (OD) (Hard drawn) with tube thickness 1.62 mm Metre 908 1,368.00 1,242,261.71

8 DSR 2022 GI Cable Tray

Supplying and installing following size of perforated Hot Dipped Galvanised Iron cable tray (Galvanisation thickness

not less than 50 microns) with perforation not more than 17.5%, in convenient sections, joined with connectors,

suspended from the ceiling with G.I. suspenders including G.I. bolts & nuts, etc. as required.

a 4.6.4 300 mm width X 50 mm depth X 1.6 mm thickness Metre 600 996.31 597,786.62

9 Providing and fixing of uPVC/cPVC/PVC drain pipe

CONTROL CABLING

Supplying, receiving, storing, laying, effecting proper connections, testing and commissioning of the following sizes

10 of 1.1 KV grade PVC insulated copper conductor unarmoured stranded control cable complete as required.

a MR 2C x 1.5 mm² Cu (Communication cable from ODU to IDU for VRF units) Metre 3850 274.00 1,054,900.00

AIR DISTRIBUTION :

(FOR DUCTS FABRICATED AT SITE AS PER “IS” CODES)

Supply, Fabrication, installation and testing of sheet metal ducts in accordance with the approved shop drawings

and as required by the specifications.

DUCT THERMAL INSULATION :

Supply and installation of Thermal insulation (Nitrile rubber) on ducts as per the approved specifications.

a 13 mm thick insulation Sqmt 180 1,302.00 234,360.00

DUCT ACCOUSTIC INSULATION :

13 Supply and installation of Duct Accoustic Insulation (OPEN CELL ACOUSTIC NITRILE INSULATION)

a 10 mm thick insulation Sqmt 80 1,713.00 137,040.00

14 Supply, Installation, Testing and Balancing of Linear Grilles

a Powder coated extruded aluminium construction with volume control damper Sqmt 2.0 17,132.00 34,264.00

b Powder coated extruded aluminium construction without volume control damper Sqmt 4.0 11,650.00 46,600.00

15 MR Supplying & fixing of opposed blade volume control dampers Sqmt 1.5 14,391.00 21,586.50

3 Digitally signed by ASHWANI

S No Description Unit Qty RATE

DSR (INR) NON-DSR (INR)

Supply, fabrication, installation and testing the flexible connections constructed of fire resistance flexible double

Supply, Installation, Testing & Commissioning of Silent type circular /rectangular inline fans for exhaust air

complete with sheet metal casing, 25mm thick acoustic insulation, direct driven centrifugal fan, motor with proper

a 200 CFM S P of 13-14 for Toilet Nos. 18 6500.00 117000.00

b 500 CFM S P of 13-14 for Kitchen Nos. 3 9500.00 28500.00

TOTAL (DSR + Non-DSR) 26,427,362.28

4 Digitally signed by ASHWANI

SCHEDULE OF QUANTITIES: IT ACTIVE & PASSIVE

S NO DESCRIPTION Unit QTY RATE

DSR (INR) NON-DSR (INR)

Supply Installation Testing & Commissioning of Cat6A AUTP 24 AWG Patch Cord Patch cord (2 mtr.): 6A UTP Patch Cords are Factory Tested for Better Quality and Suitable

for the High Speed Data Transmission. Complies to the Standard ANSI/TIA/EIA-568-C.2 Standard. Supports Data Networks Speeds Up to 10/100- Base-T and 1000-Base-T.

Available In LSZH Jacket-Reduced Toxic Gasses Emitted During Combustion , RJ45, 8P8C, 3 Prong Design for accurate termination, 50µ" Gold Plated Contacts , Insulation

1 MR Thickness 0.16mm, 100% Factory Tested , Transparent Boot Cable Assemblies.ETL Verified 4 connector channel performance with MTPL up to 635 MHz, and registered under a Sets 595 529.70 315,173.27

ETL Followup Program. Complaint to RoHS Directive 2011/65/EU and (EU) 2015/863. OEM should have ISO 9001:2015, ISO 14001:2015, ISO 45001:2018 and and should have

a certified PMP, CDCP and ITIL on the OEM’s payroll sitting in India whose services can be utilized for this project for Data as per given Specification etc. all complete

Supply Installation Testing & Commissioning of Cat6A UTP 24 AWG Patch Cord Patch cord (1 mtr.): 6 UTP Patch Cords are Factory Tested for Better Quality and Suitable for

the High Speed Data Transmission. Complies to the Standard ANSI/TIA/EIA-568-C.2 Standard. Supports Data Networks Speeds Up to 10/100- Base-T and 1000-Base-T.

Available In LSZH Jacket-Reduced Toxic Gasses Emitted During Combustion , RJ45, 8P8C, 3 Prong Design for accurate termination, 50µ" Gold Plated Contacts , Insulation

Thickness 0.16mm, 100% Factory Tested , Transparent Boot Cable Assemblies.ETL Verified 4 connector channel performance with MTPL up to 635 MHz, and registered under a

ETL Followup Program. Complaint to RoHS Directive 2011/65/EU and (EU) 2015/863. OEM should have ISO 9001:2015, ISO 14001:2015, ISO 45001:2018 and and should have

a certified PMP, CDCP and ITIL on the OEM’s payroll sitting in India whose services can be utilized for this project for Data Jack Panel end as per given Specification etc. all

Supply, Installation, Testing and Commissioning of loaded Patch Panel 24 Port Cat 6A U/UTP ,The Cat-6A transmission performance is in compliance and Exceeds

ANSI/TIA/EIA-568.2-D Standard. Supports 1000-Base-T. 90 Degree (Top Entry) or 180 Degree Punch Down Design for Convenient Network Terminations, Individual replaceable

jack module panel design as applicable.UL Listed, Complaint to RoHS Directive 2011/65/EU and (EU) 2015/863 and ASTM B 117 Certified. OEM should have ISO 9001:2015,

ISO 14001:2015and ISO 45001:2018 or latest. All networking passive material (Fiber Cable, Copper Cables, Networking Racks and their connectivity components) should be from

one OEM make only for Data as per given Specification etc. all complete

Supply Installation Testing & Commissioning of Cat6A UTP 24 AWG Patch Cord (1 mtr.): 6 UTP Patch Cords are Factory Tested for Better Quality and Suitable for the High

Speed Data Transmission. Complies to the Standard ANSI/TIA/EIA-568-C.2 Standard. Supports Data Networks Speeds Up to 10/100- Base-T and 1000-Base-T. Available In

LSZH Jacket-Reduced Toxic Gasses Emitted During Combustion , RJ45, 8P8C, 3 Prong Design for accurate termination, 50µ" Gold Plated Contacts , Insulation Thickness

4 MR 0.16mm, 100% Factory Tested , Transparent Boot Cable Assemblies.ETL Verified 4 connector channel performance with MTPL up to 635 MHz, and registered under a ETL Sets 345 445.54 153,712.87

Followup Program. Complaint to RoHS Directive 2011/65/EU and (EU) 2015/863. OEM should have ISO 9001:2015, ISO 14001:2015, ISO 45001:2018 and and should have a

certified PMP®, CDCP and ITIL on the OEM’s payroll sitting in India whose services can be utilized for this project for Voice Jack Panel end as per given Specification etc. all

Supply, Installation, Testing and Commissioning of loaded Patch Panel 24 Port Cat 6A U/UTP ,The Cat-6 transmission performance Should compliance and Exceeds

ANSI/TIA/EIA-568.2-D Standard. Supports 1000-Base-T. 90 Degree (Top Entry) or 180 Degree Punch Down Design for Convenient Network Terminations, Individual replaceable

jack module panel design as applicable.UL Listed, Complaint to RoHS Directive 2011/65/EU and (EU) 2015/863 and ASTM B 117 Certified. OEM should have ISO 9001:2015,

ISO 14001:2015and ISO 45001:2018 or latest.All networking passive material (Fiber Cable, Copper Cables, Networking Racks and their connectivity components) should be from

one OEM make only for Voice Field as per given Specification etc. all complete

Supply, Installation, Testing and Commissioning of 50 Port Voice Patch Panel for Analog Telephone system complete with connection accessories as required

Supply Installation Testing & Commissioning of 42 U 800mmX800mm Closed Network Rack with standard accessories & PDU as per given Specification etc. all

Supply Installation Testing & Commissioning of 24 U 800mmX800mm Closed Network Rack with standard accessories & PDU as per given Specification etc. all

Supply, Installation, Testing and Commissioning of Information Outlet Set(I/0) : Quard Face Plate Square (86 x 86mm) x 12 mm Shutter on Face Plate Two Piece design :

Mounting Frame and Cover Plate Should support UTP and STP Jacks Cat5e, Cat6 and Cat6A Plug Reliability : 750 Cycles minimum Cover Material : ABS UL94-V0 Base Material

: ABS- UL94-V0 Dust Cover Material : ABS-UL94-V0 ,Should have Robust and installer friendly design Surface Mount Boxes for Face Plates for a variety of media including voice

and data, Audio, video and CATV distribution to the work area. Material : ABS, Shape : Square Size : 86 x 86 , White colour. Complaint to RoHS Directive 2011/65/EU and (EU)

2015/863. OEM should have ISO 9001:2015, ISO 14001:2015, ISO 45001:2018 and should be present in India for at-least 10 years or more

Supply, Installation, Testing and Commissioning of Information Outlet Category 6A Keystone is Punch Down Type 50 Micron Gold Plating Suitable For 23~24 AWG Stranded and

Solid Wire. Skilled Design on Jack and PCB. Ergonomic Design and Easy Termination, Compliant to T568A and T568B Wiring Schemes, Backward compatible with both

10 MR RJ11/RJ12 Plug,Housing : High impact flame retardant plastic, UL 94V-O rated. ETL Verified 4 connector channel performance with MTPL up to 635 MHz, Complaint to RoHS No's 595 643.56 382,920.79

Directive 2011/65/EU and (EU) 2015/863. OEM should have ISO 9001:2015, ISO 14001:2015, ISO 45001:2018 and should be present in India for at-least 10 years or more. Blue

Colour for Data as per specification etc. all complete

Supply, Installation, Testing and Commissioning of Information Outlet Category 6A Keystone is Punch Down Type 50 Micron Gold Plating Suitable For 23~24 AWG Stranded and

Solid Wire. Skilled Design on Jack and PCB. Ergonomic Design and Easy Termination, Compliant to T568A and T568B Wiring Schemes, Backward compatible with both

11 MR RJ11/RJ12 Plug,Housing : High impact flame retardant plastic, UL 94V-O rated. ETL Verified 4 connector channel performance with MTPL up to 635 MHz, Complaint to RoHS No's 345 643.56 222,029.70

Directive 2011/65/EU and (EU) 2015/863. OEM should have ISO 9001:2015, ISO 14001:2015, ISO 45001:2018 and should be present in India for at-least 10 years or more.

Yellow Colour for Voice as per specification etc. all complete

Supply,lnstallation,Testing & Commissioning of 4 pair Cat6A U/UTP Cable, FRLSH/ RoHS complied in the existing surface/ recessed steel/ PVC conduit as required:

Supply Installation Testing & Commissioning of 6 COre MM Fiber Oprtic Cable 50 micron, OM3 complete in all respect as required.

SITC of pigtail LC/SC 1 Meter OM3 Complete in all respect as required.

SITC of 24 port LIU loaded complete in all respect as required.

1 Digitally signed by ASHWANI

S NO DESCRIPTION Unit QTY RATE

DSR (INR) NON-DSR (INR)

SITC of 10G SFP Fiber Module as required

SITC of Duplex Fiber Patch Cord (3 Mtr)

SITC of 50 Pair, 0.5mm copper, Jellyfield, Armoured Telephone Cable

SITC of 100 Pair, 0.5mm copper, Jellyfield, Armoured Telephone Cable

Supply Installation Testing & Commissioning of Layer-3 / CORE Switch : (1working + 1 Redundent) I/O ports Should Support Minimum 24 SFP+ Fiber Ports Additional

ports and slots 1 RJ-45 serial console port and one OOB port Throughput Should Support 480 Gbps Mounting and enclosure Should be 1 U rack Mountable ,Vlan Support

Should Support IEEE802.1w, IEEE802.3ac, IEEE802.3ad, IEEE802.3x, Maximum routes (Static) minimum 64 Flash Storage Should Support 256 MB,DRAM Should Support

minimum 1 GB, Dynamic Routing Should Support Minimum 2000, LACP/trunking 8 LAGs / 8 links per 9216, Maximum IGMP multicast groups minimum 500, Max PVRST 32 or

more , Power supply should support Dual AC Internal Power Supply. Temperature ranges (-0°C to +50°C (+32°F to +122°F),Operating humidity (+55° at 95% RH Storage

temperature (-40°C to +70°C (-40°F to +158°F) ,Layer 3 Features Set Should Support Dynamic Routing RIPV1/ V2, OSPF V2 , Statics Routes , Inter vlan Routing , DHCP realy .

as per specification etc. all complete with License & OEM Support of 3 years

Supply Installation Testing & Commissioning of Layer 2 48 port Non-POE Switch I/O ports 48x RJ-45 autosensing 10/100/1000 ports (IEEE 802.3 Type 10BASE-T,

IEEE 802.3—10BASE-T, IEEE 802.3u—100BASE-T IEEE 802.3ab—1000BASE-T ) 8 SFP+ fixed 1000/10000 SFP+ ports, Additional ports and slots 1 RJ-45 serial console port

and one OOB port, Throughput 128 Gbps , Internal Fans 2 or more ,Mounting and enclosure Should be 1 U rack Mountable , Maximum routes (Static) minimum 64 LACP/trunking

8 LAGs / 8 links per 9216 , Maximum IGMP multicast groups minimum 256 ,Max PVRST 32 ore more MTBF (hours) 285000 hours or more. Power supply should be AC Internal

21 MR ,Temperature ranges (-0°C to +50°C (+32°F to +122°F) ,Operating humidity (+55° at 95% RH, Storage temperature (-40°C to +70°C (-40°F to +158°F) ,Deployment Should No's 10 176,633.66 1,766,336.63

support zero touch deployment . Layer 3 Features Set Should Support Dynamic Routing RIPV1/ V2, OSPF V2 , Statics Routes , Inter vlan Routing Configration "Should support

Device profiling, automatic port configuration and network segmentation improves security posture of the network."as per the given Specification etc. all complete with License

& OEM Support of 3 years

Supply Installation Testing & Commissioning of Layer 2 24 port Non-POE Switch I/O ports 24x RJ-45 autosensing 10/100/1000 ports (IEEE 802.3 Type 10BASE-T,

IEEE 802.3—10BASE-T, IEEE 802.3u—100BASE-T IEEE 802.3ab—1000BASE-T ) 4 SFP+ fixed 1000/10000 SFP+ ports, Additional ports and slots 1 RJ-45 serial console port

and one OOB port, Throughput 128 Gbps ,POE Power Budget (Watt) 400 Watt or more , Internal Fans 2 or more ,Mounting and enclosure Should be 1 U rack Mountable ,

Maximum routes (Static) minimum 64 LACP/trunking 8 LAGs / 8 links per 9216 , Maximum IGMP multicast groups minimum 256 ,Max PVRST 32 ore more MTBF (hours) 285000

22 MR hours or more. Power supply should be AC Internal ,Temperature ranges (-0°C to +50°C (+32°F to +122°F) ,Operating humidity (+55° at 95% RH, Storage temperature (-40°C to No's 5 146,930.69 734,653.47

+70°C (-40°F to +158°F) ,Deployment Should support zero touch deployment . Layer 3 Features Set Should Support Dynamic Routing RIPV1/ V2, OSPF V2 , Statics Routes ,

Inter vlan Routing Configration "Should support Device profiling, automatic port configuration and network segmentation improves security posture of the network."as per the

given Specification etc. all complete with License & OEM Support of 3 years

Supply Installation Testing & Commissioning of Internet Firewall 10 G, Firewall throughput is crucial for maintaining efficient network performance. With a throughput of 4.6

Gbps in an Application Mix (AppMix) ensuring minimal latency even during peak usage. while the capability to handle IPsec VPN throughput at 2.3 Gbps. The firewall's ability to

manage up to 400,000 concurrent sessions makes it well-suited for high-traffic environments, ensuring robust performance even under heavy load. With a capacity for 67,000

new sessions per second. 32°F to 104°F (0°C to 40°C), ensuring reliable performance in various environments. Its non-operating temperature tolerance extends from -4°F to

The firewall is equipped with a comprehensive suite of routing protocols, including OSPFv2 and OSPFv3, The firewall supports Point-to-Point Protocol (PPP), which facilitates

direct connections between two network nodes, ensuring reliable data transmission. Additionally, it offers PPPoE (Point-to-Point Protocol over Ethernet)The firewall includes

robust multicast support, utilizing protocols such as PIM-SM (Protocol Independent Multicast Sparse Mode) and PIM-SSM (Source-Specific Multicast) to efficiently manage

multicast traffic It is featuring a ports 10/100/1000 Out-of-band Management Port: 1, RJ45 Console Port: 1, USB Ports: 2, Micro USB Console Port: 1. The firewall is equipped with

a storage capacity of 128 GB eMMC, The firewall demonstrates efficient power management with an average power consumption of 33 watts and a maximum of 41 watts, The

firewall has a maximum thermal output of 141 BTU/hr, indicating its heat dissipation under peak operating conditions , all complete with License & OEM Support of 3 years

Supply Installation Testing & Commissioning of Internet Router which can support the Fiber Line as per the given Specification. The Router should be modular in architecture

with multicore processor Router should have 2 nos. of 10/100/1000 Base T-Pots and 2 nos should have SFP based ports option. The Router should have 2 x 10G from Day 1.

Router should have 1x RJ-45 and 1xUSB Console port. should have 1:1 redundant internal and field replaceable, power supply 2 open slots for additional LAN/WAN modules,

4GB DRAM active and 8 GB Compact, DES, 3DES and AES Standard support IPSec with IKEv2 and Suite- B Encryption. 1K GRE and 1K IPSec Tunnels. OSPFv2.

24 MR OSPFv3.BGP4. MBGP.BFD. Policy based routing IPv4 and IPv6 tunnelling. Router should support 750K IPv4 and IPv6 routes ,support IGMP v1/v2/v3 and PIM multicast No's 1 691,782.18 691,782.18

routing , MPLS and Firewall feature from Dav 1 ,Shall have 802.1q class of service and marking, classification policing and shaping. support monitoring of network traffic with

application. Router shall have traffic load balancing capability on dual WAN Link based , UL 60950 or IEC 60950 or CSA 60950 or EN 60950 Standards for Safety requirement ,

IPv6 Certifies IPv6 lago ready from Day 1 as per the given Specification etc. all complete with License & OEM Support of 3 years

2 Digitally signed by ASHWANI

SCHEDULE OF QUANTITIES: EPABX (TELEPHONE & INTERCOM SYSTEM)

DSR/ AMOUNT (RS.)

S NO DESCRIPTION Unit QTY RATE

MR DSR (INR) NON-DSR (INR)

Supply, Installation, Testing & Commissioning of EPABX with 2 PRI and

300 analog extension expandable till 500 extensions capable of being

PCM/TDM with voice mail, auto apending , call forwarding etc facilities with

1 MR operator console complete in all respect as per the directions of engineer Nos 1 761,100.00 761,100.00

in charge and all complete with License & OEM Support of 3 years

SITC of Analog type Master /KTS Phones complete with handset having

features like digital display, redial, contact memory, multiple direct/landline

2 MR support (min. 6 keys), call hold /transfer & pause, electronic volume Nos 25 6,435.64 160,891.09

control, handsfree speaker phone etc. including telephone/power cords

etc. as required.

SITC of Analog type Phones complete with handset having features like

digital display, last number redial, electronic volume control, handsfree

speaker phone etc. including telephone/power cords etc. as required.

1 Digitally signed by ASHWANI

SCHEDULE OF QUANTITIES: IP Based CCTV System

DSR/ AMOUNT (RS.)

S NO DESCRIPTION Unit QTY RATE

MR DSR (INR) NON-DSR (INR)

SITC of Resolution: 5 MP (2592 x 1944) / Sensor Type and Size: 1/2.8" - CMOS 5MP Active Pixel, Progressive Scan, Back

Illuminated Image sensor (STARVIS Series) / Minimum Illuminatio Color - 0.01 Lux @ F1.2 (AGC ON) Monochrome - 0 Lux /

Focal Length: 2.8mm , Focus Range:0.3m to infinity / Field of View (FOV), HFOV – 107.6° VFOV – 57° DFOV – 127.62° / Lens

Mount: M12 / Aperture (F#): F1.6/F 2.0 / IR Range: 50m / IR Led Wavelength: 850nm / Audio IN: 1, Audio OUT: 1, Two-way

1 MR Audio Supported, SD Card Up to 512GB, Camera Adjustment Angle:- Pan: 0° to 330°, Tilt: 0° to 75°, Rotate: 0° to 330° / Nos. 60 12,821.78 769,306.93

Available Resolutions: 2592 x 1944, 2592 x 1520, 2048 x 1536,1920 x 1080, 720p, D1, VGA,2CIF,CIF, Video Compression:

H.265, H.264, MJPEG / Bitrate: 128 kbps-16Mbps (CBR, VBR) / SNR: 73dB / Edge Recording, Alarm Recording, Motion

Recording, Time-Triggered, WDR: (120dB). etc complete as per specifications of this and directions of Engineer-in-Charge

Supply, Installation, Testing & Commissioning of 32 Channel Image Resolution 12MP, 8MP, 5MP,3MP, 2MP, 720P, D1,

CIFVideo Input 32 IP Channels / Video Output HDMI (2.0) – 1 Port (Main) / Video Compression H.265/H.264/ Motion JPEG /

Audio Input 1 Channel, RCA Port(2.0Vp-p), Range (-2dBu to 22dBu) / Audio Output 1 Channel, RCA Port Mono / Audio

Compression G.711μ / Two-Way Audio / Split (Through LAN/HDMI) / Local Decoding 4x 4K, 10x 3MP, 16x 1080PF / Image

2 MR Resolution 12MP, 8MP, 5MP,3MP, 2MP, 720P, D1, CIF / Synchronous Playback 16 Channels @ 1080P (via. HDMI) / Nos. 2 223,296.04 446,592.08

Configuration Backup: Yes / Maximum User: 128 / 8 SATA III (18TB per port) / 2 NAS (CIFS/ NFS) / 1 TB USB Drive / 2 Ports x

Ethernet (RJ-45) 10/100/1000Mbps / 3 Ports (2x USB 3.0, 1x USB 3.0) / with 10TB x2 hard disk etc complete as per

specifications of this and directions of Engineer-in- Charge

Supply Installation Testing & Commissioning of 24 port POE Switch I/O ports 24x RJ-45 autosensing 10/100/1000

POE ports (IEEE 802.3 Type 10BASE-T, IEEE 802.3—10BASE-T, IEEE 802.3u—100BASE-T IEEE 802.3ab—1000BASE-T )

4 SFP+ fixed 1000/10000 SFP+ ports, Additional ports and slots 1 RJ-45 serial console port and one OOB port, Throughput

128 Gbps ,POE Power Budget (Watt) 400 Watt or more , Internal Fans 2 or more ,Mounting and enclosure Should be 1 U rack

Mountable , Maximum routes (Static) minimum 64 LACP/trunking 8 LAGs / 8 links per 9216 , Maximum IGMP multicast groups

minimum 256 ,Max PVRST 32 ore more MTBF (hours) 285000 hours or more. Power supply should be AC Internal

3 MR ,Temperature ranges (-0°C to +50°C (+32°F to +122°F) ,Operating humidity (+55° at 95% RH, Storage temperature (-40°C to Nos. 3 245,940.59 737,821.78

+70°C (-40°F to +158°F) ,Deployment Should support zero touch deployment . Layer 3 Features Set Should Support Dynamic

Routing RIPV1/ V2, OSPF V2 , Statics Routes , Inter vlan Routing Configration "Should support Device profiling, automatic

port configuration and network segmentation improves security posture of the network."as per the given Specification etc. all

complete with License & OEM Support of 3 years

Supply Installation Testing & Commissioning of 55 inch Full HD LED monitor including wall mount brackets/ clamps/desk Nos.

mounting stand.

1 Digitally signed by ASHWANI

Schedule of Quantities: Audio Visual System

DSR/ AMOUNT (RS.)

S NO DESCRIPTION Unit QTY RATE

MR DSR (INR) NON-DSR (INR)

SITC of All In One Interactive smart 136" Diagonal Screen, Pixel Pitch (mm) P1.5, Aspect Ratio 16:9, Resolution

1920×1080, Operating System Android 9.0, CPU Dual Cortex-A72 large core + four Cortex-A53 small core,

1 MR frequency 2.0GHz, RAM 4GB, Storage 32GB, built-in 2*30W audio, support 2.0 channels, Supports Bluetooth Nos 1 3,037,574.26 3,037,574.26

function with required wall mount etc all required With 3 years on Site Warranty

SITC of Screen Size 98" Interactive smart display Pixel Pitch 0.429 x 0.429 mm, Resolution 3840 (H) x 2160 (V)

4K, Brightness ≤500 Nits, Contrast Ratio ≦4000, Viewing angle 178°,178°, Response time 5ms, Display color 8

bit/16.7 Million, Backlight DLED,Speakers 2*15W With 3 years on Site Warranty

SITC of 86" 4k, UHD Professional Signedge Display with 500 NITS, 24*7 ,Built in SOC/ Media Playerwith Quad

Core Processor, Built in Open Platform Android 11, 3X HDMI, Wi-Fi/ LAN enabled, Audio Input Audio Output,

Built in Speaker(12W x 2) ;Including mounting bracket, Built-in Chromecast, Dolby Digtial audio HDMI-CEC

3 MR device linking supported, 3 USB(2.0), 3*HDMI(2.0 Side), Headphone Out, 1 *RJ 45, SPDIF out, Built In 2.4 GHZ Nos 1 355,826.73 355,826.73

Wifi,CPU Built in Mali G31 MP2 GPU-A55*4, 1.1 GHz Processer, 4 GB RAM 32GB Storage,Metal Frame 12 W

built speakers, and with 3 years on Site Warranty

SITC of 75" 4k, UHD Professional Signedge Display with 400 NITS, 24*7 ,Built in SOC/ Media Player with Quad

Core Processor, Built in Open Platform Android 11, With Built in Bluetooth, Wi-Fi/ LAN enabled, 2X HDMI, Audio

Input Audio Output, Built in Speaker(10W x 2) ;Including mounting bracket, Built-in Chromecast , HDMI Arc,

Dolby Digtial audio, The built-in SOC is powered by Google's Android Platform, HDMI-CEC device linking

4 MR supported, 2 USB(2.0), 3*HDMI(2.0 Side), Headphone Out, 1 *RJ 45, SPDIF out, Built In 2.4 GHZ Wifi,CPU Built

in With Cortex-A55*4, 1.1 GHz Processer, 2 GB RAM, 20 W built speakers, and with 3 years on Site Warranty

SITC of 65" 4k, UHD Professional Signedge Display with 400 NITS, 24*7 ,Built in SOC/ Media Player with Quad

Core Processor, Built in Open Platform Android 11, With Built in Bluetooth, Wi-Fi/ LAN enabled, 2X HDMI, Audio

Input Audio Output, Built in Speaker(10W x 2) ;Including mounting bracket, Built-in Chromecast , HDMI Arc,

5 MR Dolby Digtial audio, The built-in SOC is powered by Google's Android Platform, HDMI-CEC device linking Nos 7 125,613.86 879,297.03

supported, 2 USB(2.0), 3*HDMI(2.0 Side), Headphone Out, 1 *RJ 45, SPDIF out, Built In 2.4 GHZ Wifi,CPU Built

in With Cortex-A55*4, 1.1 GHz Processer, 2 GB RAM, 20 W built speakers, and with 3 years on Site Warranty

SITC of 55" 4k, UHD Professional Signedge Display with 400 NITS, 24*7 ,Built in SOC/ Media Player with Quad

Core Processor, Built in Open Platform Android 11, With Built in Bluetooth, Wi-Fi/ LAN enabled, 2X HDMI, Audio

Input Audio Output, Built in Speaker(10W x 2) ;Including mounting bracket, Built-in Chromecast , HDMI Arc,

Dolby Digtial audio, The built-in SOC is powered by Google's Android Platform, HDMI-CEC device linking

supported, 2 USB(2.0), 3*HDMI(2.0 Side), Headphone Out, 1 *RJ 45, SPDIF out, Built In 2.4 GHZ Wifi,CPU Built

in With Cortex-A55*4, 1.1 GHz Processer, 2 GB RAM, 20 W built speakers and with 3 years on Site Warranty

SITC of 43" 4k, UHD Commercial Display with 400 NITS, 24*7 ,Built in SOC/ Media Player with Quad Core

Processor 2.4 GHZ Wifi, CPU Built in With Cortex-A55*4, 1.1 GHz Processer, Built in Google Certified Android

11 Operating System, 2.0GB, DDR3 2133Mhz and Memory Flash 16GB EMMC, Inbuilt OTT App,With Built in

7 MR Bluetooth, Wi-Fi/ LAN enabled, Audio Input & Audio Output, Built in Speaker(10W x 2), Built-in Chromecast , Nos 2 55,198.02 110,396.04

Basic Hotel Model Function ,HDMI Arc Function, Dolby Digital Audio, HDMI-CEC device linking supported, 2

USB(2.0) x 1 , USB 3.0 x 1, 3*HDMI(2.0 Side),HDR10/HLG, Headphone Out, 1 *RJ 45, SPDIF out and with 3

years on Site Warranty

SITC of Fixed Wall Mount, capable of holding up to 75 kg and supports 37" to 100" displays, VESA Compliant etc

SITC of Cable Cubby with flip top, cover and 6 Pass Through Holes for multi-format cables, 2 Universal Power

9 MR Socket , 1 HDMI, 1 USB-C for Data Transfer, 2 Data/LAN/ Telephone etc., made of aluminium etc all complete in Nos 20 19,896.04 397,920.79

1 Digitally signed by ASHWANI

DSR/ AMOUNT (RS.)

S NO DESCRIPTION Unit QTY RATE

MR DSR (INR) NON-DSR (INR)

S/I/T/C of Digital Interactive Podium in Metallic Frame and Wooden Top with Motorized Tilting of the Touch

Panel, with dual Gooseneck Microphone, 22” Touch Panel, Keyboard Tray, and space to store AV equipment.

Should have in-built 22” Touch Monitor at the top for the presenter. Podium should have Top connectivity plate

with HDMI x 2, USB x 2 and Power socket for external Laptop connectivity.

SITC of All in One Conference Unit, Camera Sensor 1/2.5″, CMOS, Effective Pixel: 8.0M, 4 x MEMS mic array,

AEC | ANS | AGC 180° Pickup Angle pickup Range: 5-8m (16-26ft) A.I. camera with smart backlighting, auto-

framing, speaker & presenter tracking, Inputs / Outputs 1x USB-C Input with Alt-Mode, 1x HDMI Input, 1x HDMI

Output etc all complete

SITC of Network PTZ Conference Camera, 12x optical zoom and 60° horizontal FoV, 1/2.8” low-noise CMOS

Sensor, Sensor Scanning Mode: Progressive, Horizontal Rotation Range: ±170°, Vertical Rotation Range: -30° to

+90°, Image rotation for ceiling mounting, White Balance: Auto, indoor, outdoor, one-push, manual, specified color

12 MR temperature, IP Stream Resolutions: H.264 @ 360p, 270p or 180p, a single network cable for video, power and Nos 4 537,805.94 2,151,223.76

control data transport, HDMI 2.0 and 3G-SDI Outputs Power Over Ethernet (PoE) support etc all complete

SITC of 4-Input 4K Wireless Presentation and Conferencing System with Matrix Outputs, USB 3.0, Multiview &

Wireless Casting, Automatic or manual switching of 4 connected sources (2 HDMI & 2 USB-C) with assignable

USB host connection, 60W PD on the USB C Ports, Supports input resolutions up to 4K30 4:4:4 via USB-C or

HDMI Inputs: 2x HDMI In: 19-pin Type A, 2x USB-C, Wireless Video from Airplay or Miracast Source and casting

dongle (1 dongle included), Outputs: 2x HDMI Out: 19-pin Type A, 1x Analog Audio Out, Video Resolutions (Max):

HDMI Out 1 – 3840x2160p @60Hz 4:4:4, HDMI Out 2 – 3840x2160p @30Hz 4:4:4, USB: 3x USB 3.0 Type A

13 MR device ports | 5v 10000mA per port, 2x USB 3.0 Type B host ports (assignable), RS-232: 1x 4-pin Phoenix (API Nos 1 273,831.68 273,831.68

control) | Provides 12V Power, LAN: 3x 8-pin RJ-45 Ethernet Ports, Wireless: 4x Wi-Fi Antennas | IEEE 802.11

a/b/g/n/ac | Dual-band 2.4 & 5GHz | WEP, TKIP, AES, WPA, WPA2, Built-in USB 3.0 hub for connection of

peripheral devices such as speakerphones or cameras, USB-C input supports alt-mode for both A/V, Ethernet,

and Data communication over a single cable, Built-in wireless access point for secure and isolated communication

to screensharing devices, Wireless access point supports custom SSID, password and screensharing access PIN

etc all complete

SITC of 2x1 matrix for AV over IP with USB-C, HDMI 2.0 and USB 2.0 ports Full 4K HDMI 2.0 transmitter (4K

UHD @ 60Hz RGB 4:4:4, up to 18 Gbps), Video, USB2.0, Ethernet, GPIO and Serial. USB-C connectivity for 4K

video, audio, control signals and charging via USB-C up to 100W ( 120W total ). Advanced automated room

automation/control features. etc all complete

SITC of Receiver for recieving HDMI 2.0 + RS-232 + bidirectional IR, over 10G copper network cable. HDCP, 3D

15 MR and 4K / UHD ( 60Hz RGB 4:4:4 , 60Hz YCbCr 4:4:4) compliant with HDR support etc all complete Nos 4 243,464.36 973,857.43

SITC of Receiver for receiving HDMI 2.0 + RS-232 + bidirectional IR, over 10G copper network cable with analog

16 MR audio output, KVM, and full USB2.0 support. HDCP, 3D and 4K / UHD ( 60Hz RGB 4:4:4 , 60Hz YCbCr 4:4:4) Nos 1 302,870.30 302,870.30

compliant with HDR support. etc all complete

S/I/T/C of Delegate Discussion Unit complete with gooseneck microphone - with its sleek and compact form

factor, D- Cerno SL guarantees zero mobile-phone interference and a great digital sound quality. It is

17 MR equipped with tactile buttons, braille indicators, headphone connections and volume control and the Nos 36 37,376.79 1,345,564.51

cable connections are concealed for a neat overall look and feel.

S/I/T/C of Chairman Discussion Unit complete with gooseneck microphone - The chairperson unit is

18 MR same in functionalities & size of Delegate Unit will additional dedicated functionalities of Next-in-line and Priority Nos 4 43,919.37 175,677.47

SITC of Control Unit (CU) for AV Over IP product line Directly accessible SDVoE API, 3 RJ45-type Ethernet

19 MR connectors for flexible network configuration, Occupancy sensor connector Two RS232 connectors for device Nos 4 235,926.73 943,706.93

control GPIO interface for device control etc all complete

2 Digitally signed by ASHWANI

DSR/ AMOUNT (RS.)

S NO DESCRIPTION Unit QTY RATE

MR DSR (INR) NON-DSR (INR)

Fully Integrated Audio, Video and Control Solution, 128 Networked Audio Channel, 24 Channels of analog I/O,

including 8 configurable Flex channels, 16 AEC Processor, Up to 32 x 32 Dante audio channels (8 x 8 included),

20 MR USB AV bridging (16 x 16 audio + Camera Support), Full-featured Control engine (with Feature License), Up to 4x Nos 4 562,375.25 2,249,500.99

VoIP Instances, External USB audio device host etc all complete

SITC of 6.5-inch, 2-Way Ceiling Speaker, Rated Power: 30W, Frequency Range: 65 Hz – 20 kHz, Sensitivity: 88

dB, Rated Coverage 135° conical DMT, Maximum continuous SPL 106 dB, Nominal impedance: 8 / 16 Ohm,

Transformer taps: 30W / 15W at 100 / 70V, IP-34 Rated, Low-saturation and low-loss 70/100V transformers with

16Ω bypass, UL and CE Certified etc all complete

S/I/T/C of In-Ceiling Sub-Woofer with Backcan & Loopout having 1x 8 inch Driver; Frequency Range: 42 Hz – 200

Hz; Nominal Coverage Angle: 180° Conical; Power handling capacity:200 Watts Continuous Program Power 100

Watts Continuous Pink Noise; Nominal Impedance : 8Ω or 70/100V; Max SPL : 115 dB; Sensitivity : 95dB. ABS

baffle with UL94 flame class fire rating; zinc-plated steel backcan.

S/I/T/C of Hand-Held Wireless Microphone Wireless Receiver: Switching bandwidth 30.5 MHz; Diversity System

Microprocessor-controlled; Audio bandwidth 35 – 20 000 Hz (± 3 dB); Signal to noise: 120 dB-A; RF diversity

Antenna Receiver System; RF Band 3; RF Output Power 50mW, RF Output: 10, 20 or 50mW, Audio Bandwidth:

40 – 20 000 Hz (+/- 3dB); inbuilt dual color display backlight. Handheld Transmitter: Dynamic Microphone

capsules: super cardiod; Switching bandwidth: 30.5 MHz; RF output power: 10 or 50 mW Modulation / Nos 4 42,059.41 168,237.62

Bandwidth:Wideband FM; Max. SPL: 144 dB; SPL Audio bandwidth: 35 – 20 000 Hz; 1200 carrier frequencies

that can be programmed via infrared within a 30 MHz wide subband.

S/I/T/C of Head-Worn Wireless Microphone Wireless Receiver: Switching bandwidth 30.5 MHz; Diversity System

Microprocessor-controlled; Audio bandwidth 35 – 20 000 Hz (± 3 dB); Signal to noise: 120 dB-A; RF diversity

Antenna Receiver System; RF Band 3; RF Output Power 50mW, RF Output: 10, 20 or 50mW, Audio Bandwidth:

24 MR 40 – 20 000 Hz (+/- 3dB); inbuilt dual color display backlight. BodyPack Transmitter alongwith High-performance Nos 2 46,265.35 92,530.69

Headworn Condenser Microphone: Pre-polarized condenser Cardioid microphone; Frequency Range: 80 - 20000

Hz; Max SPL: 120dB; Signal to Noise Ratio: 63 dBA.

S/I/T/C of Two slot multifunctional charging station for above wireless handheld and bodypack transmitters. Each

charging slot shall accommodate a handheld or bodypack transmitter and the charger shall be capable of

charging any combination of transmitters. The batteries shall remain inside the transmitter(s) during charging. The

charger shall detect any dry (non-rechargeable) battery inside a transmitter and automatically stop the charging

cycle if a dry battery is inserted. A status LED should be there to indicate the charger's current operating status.

S/I/T/C of Digital Signal Processor with 12 Channels or more AEC analog input channels with 48v phantom power

per channel and 8 analog Output channel, 20 Hz - 20 kHz Frequency Response, network audio, 12 Control Inputs

and 6 Logic Outputs for GPIO Integration, RS232 & Ethernet Port, Signal Processing Modules such as noise

cancellation,EQs, Non Linear Processing.

SITC of Class D Dual Channel Mising Amplifier, 60 watts per channel into 4 and 8 ohms, Bridged Mode Watts per

channel: 200 W at 8 Ω & 4 Ω, 250 W at 70 V & 100 V, Signal to Noise (A weighted, 20 Hz-20 kHz) >100 dB,

Highpass Filter Switchable 80 Hz when Bridged in 70V & 100V with minimum 3 microphone inputs etc all

SITC of 4 Channel Class-D Amplifier, Power (per channels driven): 200 W at 8 Ω / 4 Ω / 100V / 70V, FlexAmp

Technology, Frequency Response: 20 Hz – 20 kHz, Signal to Noise > 103 dB, Input impedance >10k, balanced or

unbalanced, User-configurable operating modes, UL, CE, RoHS/WEEE compliant etc all complete

SITC of 10.2" Apple iPad LED-backlit Multi-Touch display with IPS technology with User Control Interface (UCI)

Deployment etc all complete

30 MR SITC of Apple docking and charging station with all required accessories etc all complete Nos 4 47,413.86 189,655.45

SITC of 24-Port Gigabit PoE+ Ethernet Smart Switch with 2 SFP Ports and Cloud Management etc all complete

3 Digitally signed by ASHWANI

DSR/ AMOUNT (RS.)

S NO DESCRIPTION Unit QTY RATE

MR DSR (INR) NON-DSR (INR)

SITC of 2 Meter Premium High Speed HDMI 2.0b Flexy Cable, Bandwidth up to 18Gbps, Up to 4096x2160@60Hz

32 MR at RGB 4:4:4 video resolution, High Dynamic Range (HDR10), Dolby Vision and Hybrid log–gamma (HLG) video Nos 67 3,935.64 263,688.12

etc all complete

SITC of 15 Meter Active Copper HDMI Cable, Data Rate: Up to 18.2Gbps, Colour Depth: Up to 16 bits, Colour

Formats: RGB 4:4:4 / Y’CBCR 4:2:2 / Y’CBCR 4:2:0, Consumer Electronic Control (CEC), Auto Lip-Sync

Correction, Audio Return Channel (ARC), Enhanced Audio Return Channel (eARC), High Dynamic Range (HDR)

etc all complete

SITC of 2 Meter USB Full-Featured Type-C cable for USB 3.1 Gen2, 4 Lane Displayport Alt mode (4K60FPS

34 MR Video and Audio), Supporting peripherals via USB 2.0 up to 480 Mbps (Mouse, Keyboard, Thumb Drive, Nos 40 4,930.69 197,227.72

Speakerphone and Webcam) etc all complete

SITC of 15 Meter USB 3.1 Gen1 SuperSpeed Active Extension Cable TypeA/male to TypeA/female, Supports 4K

35 MR Webcam, SSD storage, Native USB2/USB1 and USB3 extension, Plug and play compatible with PC, Mac, and Nos 9 36,687.13 330,184.16

Linux etc all complete

SITC of 2 Conductor 16 AWG Speaker Cable, stranded Bare copper conductors, PVC/Nylon insulation, PVC

jacket (as per actual) etc all complete

37 MR SITC of Category 6A Cable, 4 Pair, S/FTP, PVC jacket (as per actual) etc all complete Metre 1220 79.21 96,633.66

38 MR SITC of Various Cables, relay modules & Connectors etc all complete Nos 28 12,448.51 348,558.42

SITC of 9U, Equipment Rack, with Front & Side doors, 4 No Fan Assembly, on Top of the Rack, 4 Caster wheels,

39 MR 2 no Shelfs to mount the equipments, 8X2, 5/6 Amp. Power Distribution Unit, Cable Manager & Sufficient Rack Nos 0 19,366.34 -

hardwares etc all complete

SITC of 16U, Equipment Rack, with Front & Side doors, 4 No Fan Assembly, on Top of the Rack, 4 Caster

40 MR wheels, 2 no Shelfs to mount the equipments, 8X2, 5/6 Amp. Power Distribution Unit as required , Cable Manager Nos 4 31,394.06 125,576.24

& Sufficient Rack hardwares etc all complete

4 Digitally signed by ASHWANI

SCHEDULE OF QUANTITIES: FIRE ALARM & PA SYSTEM

DSR NO DSR Rates AMOUNT (RS.)

S NO DESCRIPTION UNIT QTY RATE GST Factor Cess Factor

2022 i/c Factors DSR (INR) NON-DSR (INR)

Supplying, installation, testing and commissioning of micro processor based

intelligent addressable main fire alarm panel, central processing unit with the following

loop modules and capable of supporting not less than 240 devices (including

detectors) and minimum 120 detectors per loop and loop length up to 2 km, network

communication card, minimum 320 character graphics/ LCD display with keypad and

minimum 4000 events history log in the non volatile memory (EPROM), power supply

1 17.2.1 unit (230 ± 5% V, 50 hz), 48 hrs back-up with 24 volt sealed maintenance free batteries

with automatic charger. The panel shall have facility to connect printer to printout log and

facility to have seamless integration with analog/digital voice evacuation system (which is

part of the schedule of work under SH: PA System) and shall be complete with all

accessories . The panel shall be compatible for IBMS system with open protocol BACnet/

Modbus over IP complete as per specifications

Supplying, installation, testing & commissioning of repeater panel wih 320 character/ Touch

screen LCD display with inbuilt reset, acknowledge and silence switches complete as required.

Supplying, installation, testing & commissioning of intelligent analog addressable photothermal

3 17.2.4 detector with in-built isolator complete with mounting base complete as required. Each 480 2858.00 1.0633 0.973 2956.86 1419293.18

Supplying, installation, testing & commissioning of response indicator on surface/recessed MS

4 17.2.5 Box having two LED, metallic cover complete with all connections etc as required. Each 200 276.00 1.0633 0.973 285.55 57109.42

Supplying, installation, testing & commissioning of fault isolator complete with base as required.

Supplying, installation, testing & commissioning of intelligent addressable thermal detector with

rate of rise cum fixed temperature thermistor having in-built isolator complete with base as

Supplying, installation, testing & commissioning of addressable fire control module complete as

Supplying, installation, testing & commissioning of addressable phone control module complete

Supplying, installation, testing & commissioning of addressable manual call point complete as

Supplying, installation, testing & commissioning of addressable horn cum strobe complete as

Supplying, installation, testing & commissioning of 6 zone, voice alarm controller with USB, MP3

player (including 6 zone button paging station) with seamless integration facility with main fire

alarm panel for voice evacuation complete as required.

Supplying, installation, testing & commissioning of 1.5/3/6W ceiling speaker complete as

Supplying, installation, testing & commissioning of 1.5/3/6W metal box ceiling/wall speakers

Supplying, installation, testing & commissioning of Supply of 480W RMS Single Channel Power

Amplifier, 70V/100V 4-16 ohm speaker outputs, Isolated transformer for human safety, Balanced

XLR type line input and unbalanced phone jack line input, protection of over heat, over load, clip

& short circuit, Indications for power, signal, clip, protection and temp, Frequency Response

60Hz - 15kHz, S/N ratio>70dB, THD<0.1%, Power Supply 230V AC.

Supplying, installation, testing & commissioning of Voice command keypad 6 zone, with

15 17.3.9 microphone assembly complete as required. Each 1 81756.00 1.0633 0.973 84584.01 84584.01

Supplying & laying of 2x1.5 sqmm fire alarm armoured cable, 600/1000V rated with annealed

copper conductor having XLPE insulation, steel wire armouring & FRLS outer sheath complete

1 Digitally signed by ASHWANI

DSR NO DSR Rates AMOUNT (RS.)

S NO DESCRIPTION UNIT QTY RATE GST Factor Cess Factor

2022 i/c Factors DSR (INR) NON-DSR (INR)

Supplying and fixing of following sizes of steel conduit along with accessories in surface/recess

including painting in case of surface conduit, or cutting the wall and making good the same in

case of recessed conduit as required.

Supplying and drawing of cable Fire Retardant PVC insulated copper conductor cable in the

existing surface / recessed steel conduit of following pairs, cores and size including connections

18 17.5.3 and interconnections etc. as required.

(a) 17.5.3.1 Speaker cable Single pair, 2-core, 1.5 sqmm Mtr. 2544 54.00 1.0633 0.973 55.87 142127.96

TOTAL (DSR + Non-DSR) 5070382.84

2 Digitally signed by ASHWANI

SCHEDULE OF QUANTITIES: FIRE FIGHTING SYSTEM

DSR NO Cess DSR Rates i/c AMOUNT (RS.)

S NO DESCRIPTION UNIT QTY RATE GST Factor

2022 Factor Factors DSR (INR) NON-DSR (INR)

Providing, laying, testing & commissioning of 'C' class heavy duty MS pipe conforming to IS 3589/ IS

1239 including Welding, fittings like elbows, tees, flanges,tapers,nuts bolts, gaskets etc.and fixing the

1 18.7 pipe on the wall/ceiling with suitable clamp/support frame and painting with two or more coats of

synthetic enamel paint of required shade complete as required :

Providing, fixing, testing & commissioning of 15mm dia quartzoid bulb type sprinklers of rating 68

degree centigrade with required accessories :

Supplying, installation, testing & commissioning of sprinkler flexible pipe (UL Listed) of stainless steel

complete with 15 NPT on reducer thread with maximum working pressure of 175 PSI test pressure of

3 18.25 875 PSI (Burst) with branch line (Inlet) 25mm NPT male thread to sprinkler head (Outlet) 15mm NPT

female thread with reducer, nipple, 2 side brackets, center bracket, stockbar of following sizes complete

Providing, installation, testing & commissioning of adjustable rosette plate for 15mm dia in white

finish UL Listed or FM approved complete as required

FIRE SAFETY SIGNAGE:Providing and fixing of photo luminiscent/visual markers signage made out of

photo luminiscent, produced luminization with suitable colours combination (Glow in dark) with high

intensity luminious properties covered with U/V statilized coating having following features complete as

required. (a) Thickness of

aluminium/ACP sheet 2.00 mm ±10% (b) Service temperature -

40 C to 120 C (c) Suitable for indoor surface,

glow visibility for more than 8 hrs in total darkness.

One sided signage written in English and also in regional Language,if required, for

the below dimension Fire Safety Signages.

Signage printed with the above stated specification for (i) "NO

SMOKING" with board size 4" x 12" at suitable point,

(ii) Floor indentification signage with board size 4"x12" at suitable point,

(iii) Exit signage board size 4"x12" at

suitable point, (iv) Colour signages for " Sq. inch 8294.00 18.00 149292.00

EVACUATION MAP OF EACH FLOOR" with board size of 18"x24" at suitable point,

(v)Lift Alert with board size 8'x12' at

suitable point, (v)the signages

of " FIRE ORDER" with the board size of 24"x36" at main exit/entry (Gr. Floor)

Supply,Installation,Testing & Commissioning of Carbon-di-oxide type fire extinguishers with capacity of

4.5 Kg.consisting of welded M.S.cylindrical body, internal discharge tube, discharge nozzle, suspension

bracket, conforming to IS:15683, finished externally with red enamel paint and fixed to wall with

brackets complete with internal charges.

Supply,Installation,Testing & Commissioning of Dry chemical powder type fire extinguishers of capacity

of 6 Kg consisting of welded M.S cylindrical body, internal discharge tube, discharge nozzle,suspension

7 MR bracket, conforming to IS:15683, finished externally with red enamel paint and fixed to wall with Each 12.00 4215.00 50580.00

brackets complete with internal charges.

Supply,Installation,Testing & Commissioning of "ABC Powder Automatic (Nitrogen) Type Fire

8 MR Extinguishers" of capacity 5 Kg shall confirm IS:15683 & IS:14609 with initial fill & all mounting Each 12.00 8732.00 104784.00

accessories etc.complete.

1 Digitally signed by ASHWANI

DSR NO Cess DSR Rates i/c AMOUNT (RS.)

S NO DESCRIPTION UNIT QTY RATE GST Factor

2022 Factor Factors DSR (INR) NON-DSR (INR)

Supply,Installation,Testing & Commissioning of Foam type fire extinguishers of capacity 9 Ltr.

consisting of welded M.S. cylindrical body,discharge nozzle, suspension bracket, conforming to

IS:15683 finished externally with red enamel paint and fixed to wall brackets complete with internal

Supply,Installation,Testing & Commissioning of 5 Kg Ceiling Mounted Fire Extinguisher Clean

Agent HFC, Zero ODP, Stored PressureType, Pressure Gauge, Gross Weight 7.7 Kg, empty

Weight 2.7 Kg, Can Height 267MM, Diameter 230MM, Discharge Time less than 8 Secs,

10 MR Auto discharge mechanism on temperature rise, applicable on Class A,B,C and electrically Each 6.00 32326.00 193956.00

started Fire, Can Construction : Valve Construction : Forging & Machining, Internal Coating of

Can : Epoxy Powder coating, Sheet metal thickness: 1.60 MM For HUB & UPS Rooms

TOTAL (DSR + Non-DSR) 6603654.81

2 Digitally signed by ASHWANI

SCHEDULE OF QUANTITIES: SIGNAGE

DSR/ AMOUNT (RS.)

S NO DESCRIPTION Unit QTY RATE

MR DSR (INR) NON-DSR (INR)

1 RECEPTION 3D ACRYLIC SIGNAGE

Providing, fabricating and fixing of 3D Brass Letters along with the logo raised 1.5 inches

of required size and shape with arrangement of screws in the letters itself for mounting on

MR the walls or pasting using 3M VHP Tape. Fixing complete as per directions of the Each 15 40,000.00 600000.00

engineer. Tentative Size 42"x60" , as per approved drawings.

2 NAME SIGNAGE (All Floors)

Providing and fixing of Acrylic signage made of 3mm Acrylic with textured wood finish

pasted /White milky acrylic 3mm laser cut pasted on top with proper names/ Departments

written using plottercut vinyl or laser cut acrylic letters in approved colour.Inserting

MR provision for changing names .Fixing provision using 3M VHP double sided tape as Each 150 2,500.00 375000.29

Signage Size 12x5 inch as per approved drawings.

3 FIRE EVACUATION MAP / SIGN.

Providing and fixing of Clear Acrylic sandwich frame of 3mm & 2mm acrylic with

Evacuation Plan Printed on photoluminescent media and inserted between the two frames.

MR Should be fixed on the wall using 4 Screw/ SS studs. Size 12 inch x 17 inch as per Each 15 3,000.00 45000.03

approved drawings.

4 FIRE ESCAPE EDGE-LIT SIGNAGE

Providing and fixing of Edge-Lit signage with battery backup. Made from acrylic sheet of 8

mm thickness laser engraved, Transformer to be inbuilt. Maintenance - free sealed nickel

cadmium battery included • 120V/277V AC Operation • Crystal clear acrylic face panel•

MR Engraved letters increase visibility • Anodized aluminum faceplate • Field applied chevron Each 15 3,500.00 52500.04

directional indicators simplify installation • Long life, energy-saving LED lamps • Dual-

voltage 120V/277V AC Operation • UL listed. To be installed at stairs entry. Size 310mm x

175mm as per approved drawings.

5 FIRE SAFETY SIGNAGE

Providing fabricating and fixing of signage 05 mm thick Acrylic / Sun board sheet at base

with photoluminescent film self adhesive & colored vinyl ( Red/Green) Plotter cut and

MR pasted on top. Both side / Single Side facing Complete including fixing on wall with screws

and washers or hanging on ceiling with GI chain/GI Bar complete as per technical

specifications and directions of Engineer. as per approved drawings.

Photoluminescent signages Each 15 800.00 12000.01

1 Digitally signed by ASHWANI

SCHEDULE OF QUANTITIES: LANDSCAPE

S NO DSR/ MR Ref. Image Description Unit Qty Rate

DSR (INR) NON-DSR (INR)

MossWall - Customised

“Wall Panel - Plain; Supply, Testing and

Commissioning of maintenance free Moss Wall of

size 600mm x 400mm panel. The plants shall be for

indoor use only and require no direct sunlight or

watering/ spraying of water. It is certified for sound

absobtion rate; fire resistance and has a very hostile

environment for reproduction of insects. Please

ensure 40% humidity at all times. It does not require

any trimming as well, hence a maintenance free

Make: Verde Profilo, Italy

Supply of full soil fill conical shaped planters of

specified volume and dimensions in stone finish or

equivalent. planters to be indigenously made by

rotational moulding, with homogeneous recyclable,

industrial grade polymer-resin mix, and textured

surface. planters should have an integrated water

outlet hole & plug, single layered peel-proof

construction, light weight, rust proof, uv stabilized,

MR anti-frost feature without any joints, and easy to

clean. planter supplier must give 1 year warranty

against any fading or cracking for both indoor and

outdoor use. green plant and laying is extra. potting

instructions as per company catalogue.

Plantation: Supply and installation of Natural Plant (

LARGE SIZE )with sand, fertilizer etc.

1 Digitally signed by ASHWANI

SCHEDULE OF QUANTITIES: KITCHEN EQUIPMENT

S NO DSR/ MR PARTICULARS SIZE UNIT QTY RATE

DSR (INR) NON-DSR (INR)

SERVING COUNTERS

1 MR Bain Marie With Container 60X30X34" NOS 2 42067.33 84134.65

Supplying, testing, installation & commissioning of BAIN MARIE WITH CONTAINER DIMENSION 60X30X34"

top shall be constructed with AISI stainless Steel of 16swg without back splash with 05 no. container

3container for sabji, 1 for chapatti and 1 for rice. Top of 16 swg SS sheet &amp; side covered with 18 swg SS

sheet on MS angle frame work, duly rust proof painted on SS tubular legs with adjustable bullet feet. The inner

tank is of 18 swg SS sheet &amp; fitted with auto temperature controller with water inlet &amp; outletvalves.

Other details as per general specifications etc. complete as required.

2 MR Water Cooler [40-80]LTRS. NOS 1 28497.03 28497.03

This Storage Water Cooler - 40-80 L cooling/hr and 40-80 L storage is designed to be the perfect addition to any

business that needs an efficient commercial water cooler. The stainless steel body is durable and attractive, and

the lock provides security for those who rely on their coolers for much more than just beverages. The stainless

steel water dispenser is made of high-quality stainless steel. It’s easy to handle, it can be used anywhere. The

material is corrosion-resistant and easy to wash and clean. This product has several functions: the hot water tap

can be used to supply hot water for tea, instant noodles, and other drinks; the cold water tap can be used to

supply cold water for drinking, dishwashing, and laundry washing; Can also be used as a boiling pot by removing

the upper body. This water dispenser will ensure that you never run out of clean, cold water. Its compact

dimensions and easy design makes installation a breeze and its ability to dispense hot and cold water using only

one faucet is also a great hassle-saver. Conveniently dispense water and serve your guests with our reliable

water dispenser. An ideal addition to office break rooms, classrooms, or any facility that needs constant access to

fresh, cold water. Simply add ice cubes or refrigerated coolant and it will chill the water.

Supplying , installation, testing & commissioning of CLEAN DISH RACK- DIMENSION 44X20X60"

CLEAN DISH RACK with 05no. shelves of AISI stainless steel of 18swg shelves 50 mm, front turned up

12mm @45 deg., each shelf provide "V" grooves length wise, Rear & both sides turned up 50mm &

hemmed and rack provided Legs made in 38 mm round/Square AISI Stainless Steel Pipes and feet.

Reinforced Stainless Steel hat channel provided underneath each shelf, unit to be measured 1900 mm height

x 550 mm wide and length 5 nos of shelves from AISI Stainless Steel of 18swg shall have 8mm dia

perforated hole at 100mm c/c etc. complete as required.

4 Work Table With 2 U/S 44X24X34" NOS 4 13841.58 55366.34

Supplying ,testing ,installation,& commissioning of WORK TABLE WITH 2U/S DIMENSION top shall be

constructed with AISI stainless Steel of 16swg without back splash. Table frame shall be

constructed 35 x 35 mm of Stainless Steel angle of 3mm thickness, Top and body secured to 12/25mm x 75mm x

25/12mm # 1.6 mm Thick S.S. hat type welded channel frame work. The unit shall be provided

2U/S and shall be constructed with AISI stainless Steel of 18swg. The legs should be of 38mm x 38mm x

1.6mm thick. S.S. square pipe and legs fitted with 4 nos. heavy duty GI castors with rubber wheel of 100

mm Ø, with 2 Nos. wheels should have a locking arrangement etc complete. Other details as per

general specifications etc. complete as required. Other details as per general specifications etc. complete as

5 MR Three Burner Range 60X30X34" NOS 2 25104.95 50209.90

Supplying ,testing ,installation,& commissioning of THREE BURNER RANGE WITH CAST IRON GRATE

DIMENSION 60X30X34" Grates -450X 450 or 500 mm dia as per drawing Two Burner Range fitted with

90,000 BTUs/Hr two piece ring- type cast iron brass burners with pilot lamp provides maximum cooking

performance. The frame of two burner range shall be constructed with stainless steel 4 mm of 40x40 mm angle.

The top of Stock pot range without back splash shall be constructed with AISI stainless steel of 16swg. Top

fitted on the Stainless less angle frame . Exterior frame cladding of Rear & both sides shall be of 18 swg

AISI Stainless steel, the front and control panel and Slide- out drip tray/pan shall also be of 18swg. The range

shall be provided with Heavy-duty 50 x50 mm square pipe of 16swg AISI stainless steel legs and Cross

Bracing support from all side , legs shall be fitted with the adjustable SS bullet feet. The stock pot

provided /fitted with manual heavy-duty on/off control value for Burner and pilot lamp and heavy –duty

large one-piece cast Iron 500x500 grate and pressure control regulator. The Brass Burner, pilot lamp, on/off

value and pressure control regulator shall be of United /HP make etc. complete as required.

1 Digitally signed by ASHWANI

S NO DSR/ MR PARTICULARS SIZE UNIT QTY RATE

DSR (INR) NON-DSR (INR)

Supplying, installation, testing and commissioning of SINGLE SINK DIMENSION 20X30X34" the Top

shall be constructed with AISI stainless Steel of 16swg with 100mm back splash. Table frame shall

be constructed 35 x35 mm of Stainless Steel angle of 3mm thickness, Top and body secured to 12/25mm x

75mm x 25/12mm # 1.6 mm Thick S.S. hat type welded channel frame work. The unit fitted with one unit

of sink bowl of size 450mm x 450mm x 300mm deep of 1.6mm thick AISI stainless steel pressed

sink to be provided Left/right side as per drawing and front and sink side cover with Apron by AISI 20

swg , Sink Complete waste outlet & rear connected overflow. Vertical legs- Six (4) no. 38mm x 38mm x 1.6mm

thick. S.S. Square pipe legs With adjustable SS bullet feet. The table has full width of AISI 25 mm Pipe

stainless steel bottom intermediate shelves etc. Complete as required.

7 MR Chinese Burner Range 60X30X34" NOS 1 26461.39 26461.39

Supplying ,testing ,installation,& commissioning of CHINESE RANGE RANGE WITH SANITARY FITTING WITH

CAST IRON GRATE DIMENSION (mm) 60X30X34" Grates -450X 450 or 500 mm dia as per drawing

Two Burner Range fitted with 90,000 BTUs/Hr two piece ring- type cast iron brass burners with pilot lamp

provides maximum cooking performance. The frame of two burner range shall be constructed with stainless steel

4 mm of 40x40 mm angle. The top of Stock pot range without back splash shall be constructed with AISi

stainless steel of 16swg. Top fitted on the Stainless less angle frame . Exterior frame cladding of Rear &

both sides shall be of 18 swg AISI Stainless steel, the front and control panel and Slide- out drip tray/pan

shall also be of 18swg. The range shall be provided with Heavy-duty 50 x50 mm square pipe of 16swg AISI

stainless steel legs and Cross Bracing support from all side , legs shall be fitted with the adjustable SS

bullet feet. The stock pot provided /fitted with manual heavy-duty on/off control value for Burner and

pilot lamp and heavy –duty large one-piece cast Iron 500x500 grate and pressure control regulator. The

Brass Burner, pilot lamp, on/off value and pressure control regulator shall be of United /HP make etc.

complete as required.

Supplying ,testing ,installation,& commissioning of DOSA PLATE 48X30X34" -. The dosa plate shall be of 15

mm thick polished mild steel plate sloped towards the front to a 25 mm wide grease gutter pitched to an opening

to collect grease in a drawer. Panel/Frame– Exterior panel/ cladding shall be constructed with AISI

stainless steel of 20swg and the internal structure/ frame of Stainless steel 45 x45 mm angle of 5 mm thick,

Verticals legs – AISI stainless steel 50 mm diameters /50x50 mm square tubing of 16swg with bottom

pipe shelf of 38 mm dia/38x38 m square pipe the gap between the grids shall be 75 mm and shelf shall be above

150 mm from the floor level, all four legs are fitted with adjustable bullet feet. . Fitting- The equipment shall be

duly connected with the best quality copper pig tails, needle valves and shall be will be fitted with 2 nos.

of heavy duty V shape United/HP burners with indusial needle control knob to give evenly distributed heat, to

be operated at 0.3 kg/cm2 (4.5 PSIG) gas pressure. The main line will be of 1” dia BSP ‘C’ Class ERW M.S.

pipe and pressure tested etc. complete as required.

9 MR Wall Mounted Pizza Oven STONE BASE NOS 1 23069.31 23069.31

Imported, Stone Base Pizza Oven - Wall Mounted Electric equipment

10 MR Pulverizer (Heavy Duty) 3HP NOS 1 23883.17 23883.17

Supplying ,testing ,installation,& commissioning of WET MASALA GRINDER/GRAVY MACHINE Capacity

80Kg/hrs. The UNIT inner frame is made of SS grade Stainless Steel. Grind bulk quantities of wet

masala, chutney, ginger paste, garlic paste, red chili & coriander paste, tomato puree. The Unit with 3 hp

3phase Motor motor etc. Other details as per general specifications etc. complete as required.

11 MR Dish Landing Table 44X30X34" NOS 2 14926.73 29853.47

2 Digitally signed by ASHWANI

S NO DSR/ MR PARTICULARS SIZE UNIT QTY RATE

DSR (INR) NON-DSR (INR)

Supplying , installation, testing & commissioning of SOILED DISH DROP OFF TABLE WITH

GARBAGE CHUTE & DRAIN TROUGH DIMENSION 44X24X34"Soiled dish table the Top shall be

constructed with AISI Stainless steel of 14swg. Soiled dish drop table front & free sides turned up

75mm, returned 40mm, turned down 50mm & in 12mm and provided with Back splash of 200mm High &

garbage chute of 150mm dia at LHS/RHS as per drawing. The table top shall be fitted with 100mm x 40mm

deep 1.6mm thick stainless steel Trough with Stainless steel perforated anti splash grating & Drain in

the front side. Top secured 40 mm x 40 mm of 4 mm thick stainless steel angle frame work. Top from

the bottom shall be supported vertically with 40mm x 4 mm thick strips with 200 mm gap the strips are

reinforced with angle frame Vertical Legs – Legs (no of legs shall be 6) shall be constructed with 38mm x 38mm

x 16swg thick square pipe legs. With adjustable SS bullet feet. Table shall be provided with 1000

mm cross bracing 25mm x 25mm x 1.6mm thick stainless steel square pipe cross bracing welded to

legs at Rear & both sides and Front & reaming bottom with u/s of AISI 18SWG etc. complete as

12 MR Three Sink Unit 60X30X34" NOS 2 24425.74 48851.49

Supplying , installation, testing & commissioning of DISH WASH THREE SINK WITH DASH BOARD

UNIT DIMENSION 60X24X34" sink bowl size -600x600x 400 SS pot sink unit –shall be

constructed with AISI stainless steel of 14 swg, the unit shall be provided with 200 mm high back splash. Sink

front turned up 25mm, returned 40mm, down 75mm & in 12mm. Top secured to 40 x 40mm of 4 mm thick

S.S. angle welded frame work reinforced with 38mmx 38mm x 16swg thick AISI stainless steel square pipe

legs. With adjustable bullet feet. The legs support provided with 25mm x 25mm x 1.6mm thick SS pipe

PIPE SHELF welded to legs at Rear & both sides and Front & three side side provided with the stainless

steel 20swg apron.) etc. Other details as per general specifications etc. complete as required.

13 MR Wall Mounted Rack 60X12" NOS 2 10856.44 21712.87

Supplying, installation, testing and commissioning of WALL SHELF DIMENSION (mm) 60X12" Shall be

constructed with AISI Stainless Steel of 18swg ,rear and both side turned up 50 mm, hemmed outside and,

front turned down 38mm & in 12mm. Shelves secured to bracket with acorn stainless steel nuts & bolts. Wall

shelf bracket shall be constructed in AISI Stainless Steel 14 swg and Secured to top with acorn Nuts & Bolts

& Bracket secured to wall with anchor fasteners etc complete as required.

14 MR Four Door Refrigerator 54X30X78" NOS 1 96346.53 96346.53

Supply, installation, testing and commissioning of FOUR DOOR VERTICAL CHILLER

DIMENSION (mm) 1400 X 820 X 2050 upright vertical Refrigerator as per specified make and model a

unit made from ASAI Stainless steel interior, with Four (4) no. of Doors with insulation & removable gasket for

easy clean, Internal Temp+ 2 Deg C to+ 8 Deg C & Refrigerant Gas: R-134 A, Uniform cooling by

forced air circulation system with Copper condenser, and Removable & Adjustable shelve Celfrost

[USA]/Steller etc. Other details as per general specifications etc. complete as required.

15 MR Deep Freezer 550LTRS NOS 1 29854.46 29854.46

The VT low temperature freezers creates the possibility to maintain temperatures as low as -60°C. Supreme

stability, reliability, user-friendliness and ease of cleaning make these freezers an ideal solution for laboratories

and hospitals. Nature R refrigerant, cyclopentane insulation combined with recyclable materials make the freezers

extremely eco-friendly.

16 MR Dish Landing Table 44X30X34" NOS 2 14926.73 29853.47

Supplying , installation, testing & commissioning of SOILED DISH DROP OFF TABLE WITH

GARBAGE CHUTE & DRAIN TROUGH DIMENSION 44X24X34"Soiled dish table the Top shall be

constructed with AISI Stainless steel of 14swg. Soiled dish drop table front & free sides turned up

75mm, returned 40mm, turned down 50mm & in 12mm and provided with Back splash of 200mm High &

garbage chute of 150mm dia at LHS/RHS as per drawing. The table top shall be fitted with 100mm x 40mm

deep 1.6mm thick stainless steel Trough with Stainless steel perforated anti splash grating & Drain in

the front side. Top secured 40 mm x 40 mm of 4 mm thick stainless steel angle frame work. Top from

the bottom shall be supported vertically with 40mm x 4 mm thick strips with 200 mm gap the strips are

reinforced with angle frame Vertical Legs – Legs (no of legs shall be 6) shall be constructed with 38mm x 38mm

x 16swg thick square pipe legs. With adjustable SS bullet feet. Table shall be provided with 1000

mm cross bracing 25mm x 25mm x 1.6mm thick stainless steel square pipe cross bracing welded to

legs at Rear & both sides and Front & reaming bottom with u/s of AISI 18SWG etc. complete as

3 Digitally signed by ASHWANI

S NO DSR/ MR PARTICULARS SIZE UNIT QTY RATE

DSR (INR) NON-DSR (INR)

17 MR Ss Exhaust Hood With Oil Filters FT 25 2442.57 61064.36

Supplying ,testing ,installation,& commissioning of EXHUAST HOOD WITH FRESH AIR PLENUM

DIMENSION. Fabricating , Supplying, fixing, installation and commissioning of. exhuast hood , Hood build with

AISI Stainless steel of 20swg and hood filters framework shall be of 45° ,all joint are fully welded, all

hoods frame work are provided with removable Stainless steel 500 x 500 mm baffle filters,all filters are

compatible by way of washable in dishwasher. Exhaust hoods provided fitted with oil drain channel and

grease collection tray,hoods frame work are provided with removable Stainless steel 500 x 500 mm baffle

filters,all filters are compatible by way of washable in dishwasher. All hoods top shall be fitted with the Stainless

steel bracket at all the four corners for the hanging of the hoods with the ceiling through screw rod. Back-shelf

hood- apart from above spec, unit shall be constructed, 100 mm high at the front and 500 mm high at

therear, The entire hood will be fabricated either in one pieces but after connecting it should be one piece

wall type hood. Baffle filters- The filters shall have an outer frame constructedwith stainless Steel of 20

swg and inner “C” type strip of 25x 32 x 25 mm in 22swg stainless steel , channels shall be welded,

which will form a baffle for air movement. The filters and framework shall be provided with weep holes for

draining of oil Exhaust Hood Electrical Fittings- all hoods shall be provided Appropriate numbers of flashedi

light cover glass, to provide 200 Lux-level of light through-out the hood, etc. complete as required.

Supplying, Installation, Testing and Commissioning of double skin construction (25 mm thk. PUF panel) (of

similar specification as that of AHU) SCRUBBER unit for Kitchen exhaust. The unit shall comprise of Air

intake section with Volume Control Damper, Aluminium wire mesh filters, double bank spray air washer

complete with FRP/1.2 mm thick. SS- water tank, water circulation pumps along with inter connection GI

piping,spray nozzles,valves, fittings, 4 bend PVC eliminators etc. Inner skin of SS- in wet section. Blower

section will consist of DIDW class-I centrifugal fan (Efficiency >70%) with TEFC weather proof VFD

Compatiable motor with built in harmonic filters of IP55 protection 415±10% volts, 3 phase, 50 cycles

power supply, IE3 belt drive, multisheave pulley mounted on motor and fan shaft, belt guard, motor and fan

mounted on common base with metallistik vibration isolators. Fan capacity shall be based on outlet

velocity not exceeding 650 M/minute and fan speed not exceeding 1400 RPM. Fan shall be

selected for maximum 3 inch static pressure. 2 Nos (1Working+1 Standby) horizontal monobloc pumps,

factory mounted on GI channel base with electric motor shall be used for circulation of water. Pumps shall be

aligned and suitable for 415±10% volts, 50 cycle’s 3 phase power supply. Pump shall be interlocked with

scrubber fan motor and water level sensor etc complete as required.

Supplying, Installation, Testing and Commissioning of factory fabricated Double Skinned Air-washer unit floor mounted type fabricated out of extruded aluminium section with 0.6 mm pre-plasticized / pre- coated Galvanised steel s

GI Ducting [8 X 4 = 32sqft/sheet]

MR 50 sheet (approx.) X 32sqft = 1600 sqft. (approx.)

Supply, installation, testing and commissioning of GI Thickness 1.00 mm sheet volume control duct

damper complete with neoprene rubber gaskets, nuts, bolts, screws linkages, flanges etc, as per

21 MR Fresh Air Ducting [8 X 4 = 32sqft/sheet] SQ FT 500 95.05 47524.75

Supply, installation, testing and commissioning of GI Thickness 1.00 mm sheet volume control duct

damper complete with neoprene rubber gaskets, nuts, bolts, screws linkages, flanges etc, as per

22 MR Fresh Air Grill - 2sqm. NOS 8 1085.15 8681.19

Supplying & fixing of powder coated extruded aluminium Return Air Grills with louvers but without

volume control dampers complete as required

23 MR Gas Pipeline Gas Manifold - Complete 5+5 LPG cylinder Manifold with all accessories FT 50 959.00 47950.00

4 Digitally signed by ASHWANI

S NO DSR/ MR PARTICULARS SIZE UNIT QTY RATE

DSR (INR) NON-DSR (INR)

Supply, Installation ,testing and commissioning of 5 +5 MANIFOLD constructed with C.S. Seamless Pipe

25mm Sch. 40, GAS PIPELINE C.S. Seamless Pipe 40 mm Sch. 40/3.91 mm thickness, Including All IBR

approved fittings mainfold provided with including one Coat of Red Oxide and 2 coat of Yellow Enamle

Paint Manifold fitted with following Compents;- a). Manifold C.S. Seamless Pipe 25mm Sch. 40 for 5+ 5

LPG Cylinder- 2 Nos. b). BALL VALVE 25mm-4 Nos c). BALL VALVE 15mm-1 No.d). PRESSURE

GAUGE 4"- 1 No.e). Pressure Regulator Value( PRV)R-2316 40MM- 2 Nos.f). Slam Shut Valve (SSV)

V-4327 40MM- 1 No.g). FLASH BACK ARRESTOR 40 mm- 1 No.h). Flexible Cylinder Pigtail- 10

Nos.i). CLYD ADOPTERS- 10 Nos.j). NRV Brass- 10 Nos.k). FLANGE 40 mm IBR Approved- 4 Nos.l).

STUD-16 Nos.m). Gasket- 8 Nos.n). Earthing Jumper Copper Fork 1.5"- 4 Nos.o). FILTER 40 mm- 1

No.p). MISC FITTIN pipe legs. With adjustable SS bullet feet. Table shall be

5 Digitally signed by ASHWANI

SCHEDULE OF QUANTITIES: LIFTS

DSR/ AMOUNT (RS.)

S NO DESCRIPTION Unit QTY RATE

MR DSR (INR) NON-DSR (INR)

SITC for Machine Room Less CAPSULE Type Elevator (MRL LIFTS) ,408 Kg, 6 persons, 1mps speed, 13 mtr, (G+2)

03 Stops With (all opening on the same side) LVA/ACD , VF Regenerative (Closed Loop) ,400/415 Volts (3 Phase

AC) ,Full collective operation , Two car (Duplex) , PM Gearless ,Flat Coated Steel Belt ,CD-41 , Fire rated Glass for

Side wall panels , Stainless Steel Mirror Finish Handrails on rear & side car panels ,Cross flow fan, 20 mm recess

GRANITE flooring , Fire rated Glass doors with SS hairline finish frame , overhead as per OEM, Hoist-way dimension

1600 mm W x 1600 mm D, car dimension : 1000 mm W x 1100 mm D x 2200 mm H , Central opening (CO) doors

min. 700 mm W x 2000 mm H , DC Door Operator, COP for stops <= 12 (950mm) in Stainless Steel #4(Hairline),

1 MR LOP, up/down & floor level indicators in stainless steel, Monochrome LCD-Blue Background & White font ,O2000 ,Hall Nos. 2 1,903,379.09 3,806,758.18

Button with HPI, Anti-nuisance Car Call Protection, Independent Service (for Duplex), Overload Device, Nudging

,Emergency Firemen’s Service, Emergency Car Light Unit Infrared Curtain Door Protection, Door Time Protection,

Emergency Alarm, Extra Door Time of Lobby & Parking Door, Open/Close Button, Manual & Automatic Rescue

Operation, Belt Inspection Drive Auto Fan Cut Off etc. including ARD with Batteries, LED lights, CCTV Cam in each

Car, Intercom etc. complete in all respect as required.

SITC for Machine Room Less CAPSULE Type Elevator (MRL LIFTS) ,408 Kg, 6 persons, 1mps speed, 9 mtr, (G+1)

02 Stops With (all opening on the same side) LVA/ACD , VF Regenerative (Closed Loop) ,400/415 Volts (3 Phase

AC) ,Full collective operation , One car (Simplex) , PM Gearless, Flat Coated Steel Belt ,CD-41 , Fire rated Glass for

Side wall panels , Stainless Steel Mirror Finish Handrails on rear & side car panels ,Cross flow fan, 20 mm recess

GRANITE flooring , Fire rated Glass doors with SS hairline finish frame , overhead as per OEM, Hoist-way dimension

1600 mm W x 1600 mm D, car dimension : 1000 mm W x 1100 mm D x 2200 mm H , Central opening (CO) doors

min. 700 mm W x 2000 mm H , DC Door Operator, COP for stops <= 12 (950mm) in Stainless Steel #4(Hairline),

2 MR LOP, up/down & floor level indicators in stainless steel, Monochrome LCD-Blue Background & White font ,O2000, Hall Nos. 1 1,591,917.06 1,591,917.06

Button with HPI, Anti-nuisance Car Call Protection, Independent Service (for Duplex), Overload Device, Nudging

,Emergency Firemen’s Service, Emergency Car Light Unit Infrared Curtain Door Protection, Door Time Protection,

Emergency Alarm, Extra Door Time of Lobby & Parking Door, Open/Close Button, Manual & Automatic Rescue

Operation, Belt Inspection Drive Auto Fan Cut Off etc. including ARD with Batteries, LED lights, CCTV Cam in each

Car, Intercom etc. complete in all respect as required.

1 Digitally signed by ASHWANI