SPECIAL REPAIR TO BLDG NO O13 BLOCK (TRANSIT OFFICERS FAMILY ACCN) INSIDE FORT WILLIAM UNDER GE FORT WILLIAM KOLKATA

Amount

NOTES :The bidders/contractors are advised to read tender document & all corrigendum/ amendments and General conditions of contracts before entry/quoting the rates.

Dismantling AC roof corrugated steel sheet, thickness including eves gutter / rain water pipe complete & removal all as specified

Dismantling steel work including gates, rafter, purlin, roof truss etc complete all as specified & as directed.

Material, labour and fixed for rolled sections as in main and cross beams, hip and jack rafters, purlins where connected to common rafters and running rails and guides for sliding doors, fixed with angle cleats, Fe-410-W(Gde-E 250) Quality A complete all as specified and as directed.

Supply and fixing rolled mild steel, joist, channel, angle or Tee section fixed independently without connecting plates etc up to height 6 to 7 mtr from each floor level (cut to ordinary length ie. without 20mm of the length indicate) Grade E-250(Fe-410W) Quality A including dismantling of exsting structural members completion all as specified and as directed.Note: 1. The Sections to be provided under this item will be used as beams to support floors/roofs after removing the the existing wooden/rusted iron beams. 2. The supports for roof before removing the old wooden/rusted iron beams shall be properly designed and put in place before removing the old beams and replacing it with new beam. 3. The rate quoted for this item shall be inclusive of the charges for temporary support system provided which shall be removed after placing new beam in position. 4. The temporary supports during replacement of of beams and other componants shall consist of tubular steel props minimum 65mm dia and placed at proper spacing and braced for shoring/support of existing structure during execution of work.

Stripping out tarfelt from old roof surfaces and removing unserviceable materials from site of work in low laying in outside MOD area and brushing and applied neat cement slurry with 3.0 Kg of cement per Square Metre existing surface complete all as specified and as directed.

Material and labour for Plain Cement Concrete M-15(Nominal Mix) using 20 mm graded stone aggregate in roof kerbs or mud stops, benching,rounded or chamfered on edges including preparation of old roof surface with brushing and applied neat cement slurry with 3.0 Kg of cement per Square Metre existing surface complete all as specified and as directed

Material and labour for rendering 15 mm(Avg) thick in Cement Mortar 1:4 finished even and smooth witht using extra cement after preparation of old roof surface with brushing with water proofing treatment complete all as specified and as directed . Note:- Water proofing compound shall be measure and paid separatel

Material and labour for cutting out cracks to V-section in existing roofs or terracing, cleaning out, wetting, grouting with cement and sand slurry 1:3 all complete complete all as specified and directed.

Supplying and laying 3mm thick APP (Atactic Polypropylene Polymer) modified prefabricated five layer, weight not less than 3.6 kg/Sqm water proofing membrane, black finished reinforced with non woven polyester matt laying over a coat of bituminous primer @ 0.40 Ltr / Sqm and two coats of Bitumen based UV reflective paint with aluminium finish over APP membrane. The membrane shall be laid using butane torch and sealing all joints etc all as specified in Para 11.44.5 of SSR Part I complete all as specified and as directed.

Demolition of cement concrete (un-reinforced) in ground floors, sunken floor and paving complete all as specified

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to stores and rubbish off the MOD premises complete all as specified and as directed.

Dismantling stone slabs and tiles of laid in bedded and pointed in any mortar any description or thickness in floors, aprons etc.

Material and labour for 75 mm thick plain cement concrete M-10(Nominal Mix) using 20 mm graded stone aggregate as in plinth protection, finished even and smooth without using extra cement complete all as specified and as directed.

Material & Labour Non skid ceramic tiles, coloured, 7 to 8 mm thick (square/rectangular area of each tile exceeding 0.11 Sqm and not exceeding 0.18 Sqm , in floors etc. Set and jointed in neat cement slurry and pointed in white or coloured cement to match over 15mm thick screed bed layer in CM (1:4) including roughening surfaces of old concrete floor by picking, sweeping clean and washing down with water to remove dust, etc and brushign neat cement slurry with 3.0 kg of cement per Sqm complete all as specified and as directed.

All as per item no15 but as in skirting/dado but over 10 mm thick rendering over CM 1:4

Material & Labour Glazed ceramic tiles 450x300/ 300x200 x7 mm(Coloured) on vertical surfaces such as skirting, dados and riser to steps etc. set and jointed in neat cement slurry and pointed in coloured cement to match complete over 10mm thick screed bed vertical layer in CM (1:4)all as specified and as directed.

Material & Labour of vitrified ceramic tiles,double charged, light coloured shade, 10 mm thick of square/rectangular area of each tile not exceeding 0.36 Sqm , in floors etc. set and jointed in neat cement slurry and pointed in coloured cement to match over 15mm thick screed bed layer in CM (1:4)complete all as specified and as directed.

All as per item No 18here-in-before but to vertical surfaces such as skirting over and including 10mm thick rendering in CM (1:3) complete

Material & Labour of 18mm thick granite ( of any type) work ( table rubbed and polished in pillars and like set in cement mortar (1:4) including pointing in white cement (1:2) using marble dust admixture of pigment to match with shade of granite over 15mm thick screed bed layer in CM (1:4) complete all as specified and as directed.

All as per item No 21here-in-before but to vertical surfaces such as skirting over and including 10mm thick rendering in CM (1:3) complete

Material and labour for pre-polished chequered Cement Concrete tiles of 25 mm minimum thick, size of (square/ rectangular) area of each tile exceeding 0.09 Sqm but not exceeding 0.16 Sqm double layer machine pressed set ( as per IS 1237-2012), jointed and pointed in neat cement slurry in floors and cut & polished in white or coloured cement to match over and including 15mm thick screed bed in CM (1:6) complete all as specified and as directed.

Demolition of brickwork or stone/ boulder masonry, built in cement mortar including all quoins, arches, pillars, etc, but excluding ashlar facings, dressed stonework and precast concrete articles complete all as specified and as directed.

Cutting holes in brick walls exceeding half brick but not exceeding one brick built in cement mortar for inserting hold fasts of GI pipe and making good dismantled portion in cement concrete 1:2:4 type B1 exceeding one brick.

Material and labour for Brick work with bricks class designation 75, old size, straight or curved on plan exceeding 6 m mean radius built in Cement Mortar 1:6 complete all as specified and as directed.

Material and labour for brick work with bricks class designation 75, size as per old size brick, straight or curved on plan exceeding 6 m mean radius half brick thick walls built in Cement Mortar 1:4 complete all as specified and as directed.

Material and labour for Precast Reinforced Cement Concete jalli type M-15(Nominal Mix) B-0 using 12.5mm graded stone aggregate, set in Cement Mortar (1:4), 25 mm thick, including all moulding but excluding frame compound complete all as specified and directed.

Taking down cement plaster, any description on brick or stone walls, etc. including raking out joints, hacking for key, scrubbing down with water, etc. and removal outside of MOD land complete all as specified and as directed.

Rendering 15 mm in Cement Mortar 1:6 on fair faces of brick work or concrete surfaces finished even smooth without using extra cement to the plastered surface complete all as specified and as directed.

Material and labour for Rendering 10mm thick plaster in Cement Mortar (1:3) on fair faces of concrete surface on ceiling and finished even and smooth with using extra cement, with water proofing treatment.

Supply only integral liquid water proofing compound

Material and labour for preparation of old plaster wall surface and applying two coats of polymer modified, flexible cementatious waterproof coating(damp block paint) and as per manufacturer’s specification over a coat of primer over a coat of 1.0 mm thick cement base wall putty complete all as specified and directed.

Material and labour for Preparation of new plaster wall surface and applying two coats of 1st quality acrylic washable distemper (ready mixed) having VOC content less than 50 gms/litre of required colour shade and as per manufacturer’s specification over a coat of primer over a coat of 1.0 mm thick cement base wall putty complete all as specified and directed.

Material and labour for Preparation of new plaster ceiling surface and applying two coats of 1st quality acrylic washable distemper (ready mixed) having VOC content less than 50 gms/litre of required colour shade and as per manufacturer’s specification over a coat of primer complete all as specified and directed.

Material and labour for complete removal of existing finishing of internal wall surface of building/structure by mechanical appliance and preparation of old surfaces and applying two coats of 1st quality acrylic washable distemper (ready mixed) having VOC content less than 50 gms/litre of required colour shade and as per manufacturer’s specification over a coat of primer over a coat of primer over a coat of 1.0 mm thick cement base wall putty complete all as specified and directed.

Material and labour for complete removal of existing finishing of internal wall surface of building/structure by mechanical appliance and preparation of old surfaces and applying two coats of 1st quality acrylic washable distemper (ready mixed) having VOC content less than 50 gms/litre of required colour shade and as per manufacturer’s specification over a coat of primer over a coat of primer complete all as specified and directed.

Material and labour for complete removal of existing finishing of internal ceiling surface of building/structure by mechanical appliance and preparation of old surfaces and applying two coats of 1st quality acrylic washable distemper (ready mixed) having VOC content less than 50 gms/litre of required colour shade and as per manufacturer’s specification over a coat of primer over a coat of primer complete all as specified and directed.

Material and labour for preparation of old internal wall surface of building/structure and preparation of old surfaces and applying one coats of acrylic washable distemper complete all as specified and directed.

Material and labour for preparation of old internal ceiling surface of building/structure and preparation of old surfaces and applying one coats of acrylic washable distemper complete all as specified and directed.

Material and labour for preparation of old internal wall surface of building/structure and preparation of old surfaces and applying one coats of plastic emulsion paint complete all as specified and directed.

Material and labour for preparation of old internal wall surfaces and applying a coats of white wash complete all as specified and directed.

Material and labour for preparation of old internal ceiling surfaces and applying a coats of white wash complete all as specified and directed.

Material and labour for Preparation of old external wall surface and applying one coat of cement based paint of any description over 10 cm girth or width complete all as specified and directed.

Material and labour for complete removal of existing treatment of external wall surface of building/structure by mechanical appliance and preparation of old surfaces applying two coats of acrylic exterior weather resistant paint(weather proof paint @ 1.67 ltr/10 sqm per two coats ) of required colour shade and as per manufacturer’s specification over a coat of acrylic exterior primer((@ 2.20 kg/10 sqm) over a coat of 1.5 mm thick cement base wall putty complete all as specified and directed.

Material and labour for Preparation of old external wall surface and applying one coat of acrylic exterior weather resistant paint(weather proof paint )of any description over 10 cm girth or width complete all as specified and directed.

Material and labour for preparation ofold wooden surface and applied one coat of varnishing on surfaces of any description, width or girth including cleaning and preparing the surface complete all as specified and as directed..

Material and labour for Preparation of old steel surface and applying one coats of synthetic enamel paint on steel surfaces of any description over 10 cm in girth or width complete all as specified and directed.

Material and labour for Preparation of old plaster surface and applying one coats of synthetic enamel paint on steel surfaces of any description over not exceeding 10 cm in girth or width complete all as specified and directed.

Material and labour for preparation of old wooden surface and applying one coats of synthetic enamel paint on wood surfaces of any description over 10 cm in girth or width complete all as specified and directed.

Taking down chowkats/frames with shutters (without taking off shutters from the frame) etc. exceeding 1.50 Sqm but not exceeding 4.00 Sqm each complete all as specified and as directed.

Taking down chowkats/frames with shutters (without taking off shutters from the frame) etc. not exceeding 1.50 Sqm each complete all as specified and as directed.

Taking down shutters of any description n exc 1 sq. m each complete all as specified and directed.

Taking down shutters of any description exc 1 sq. m and n exc. 2 Sqm each complete all as specified and directed.

Dismantling timber scantling 40 Sqcm and over in section, in any position (Unframed work) complete all as specified and as directed.

Dismantling wall and ceiling boards (fibre, pulp, insulation, etc.) or insulation boards / slabs / blankets, any thickness, including cover fillets, etc complete all as specified and as directed.

Mild steel work as in bands, straps, supports or stays for RWP, ventilating pipes, clamps, hold fasts, wall ties conforming to Fe-290 Gde E-165

Material and labour for 2nd class hardwood timber clean sawn fixed as in scantlings, purlins, trusses complete all as specified and directed

Supply and fixing of 2nd class HW Plain, solid, straight chowkats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints, supplied and fixed complete all as specified and directed.

Material and labour fo second Class hardwood plain fillets square in section, clean sawn, fixed with nails, sectional area exc.3 Sq cm but not exc. 6 Sq cm. complete all as specified & as directed.

Material and labour fo second Class hardwood plain fillets square in section, clean sawn, fixed with nails, sectional area exc.6 Sq cm but not exc. 13 Sq cm. complete all as specified & as directed.

Material and labour for PCC 1:2:4 type B-2 using 12.5mm graded crushed aggregate as in RWP mouth, leakage arrest mixed with WC over roof surface, filling in holdfast/ filling in pressed steel frame complete all as specified and directed.

Material and labour for 35 mm thick plain framed, factory made panelled shutter (second class hard wood rails & styles) (two panel) with lock rail and panel of 9 mm B.W.P. commercial ply or 12 mm veneered particle board with commercial veneering on both faces. The size of rail and stile as per IS : 1003 (Part I), kiln seasoned and chemically pressure treated. complete all as specified and as directed.

Material and labour for 30 mm thick, second class hard wood, factory made glazed and skeleton shutters, open rebated and prepared to receive gauze, etc. with plain chamfered or rounded, mitred and rebated sash bars any numbers, edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass, etc.; sizes of members of shutters as specified in SSR Part I, Section 8, clause 8.24 (a); supplied and fitted to chowkats complete all as specified and as directed.

Supply and fixing of 30 mm thick flush shutters, solid core construction, with block board core and comercial plywood face panels with one face is covered with decorative face veneer with lipping/frame to match all complete all as specified and as directed.

Material and labour for factory made single extruded WPC (Wood Polymer Composite) solid door Frames/ Chowkhat of size 65x100mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum comp¬ressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge. Note: 1. For WPC solid door/window frames, minus 5mm tolerance in dimension i.e. depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made. 2. M.S. hold fast/ lugs or SS dash fasteners shall be paid for separately"

Material and labour for factory made single extruded WPC (Wood Polymer Composite) solid door Frames/ Chowkhat of size 65x150mm (Double rebate)comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum comp¬ressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge. Note: 1. For WPC solid door/window frames, minus 5mm tolerance in dimension i.e. depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made. 2. M.S. hold fast/ lugs or SS dash fasteners shall be paid for separately

Material and labour for Solid PVC door frame of size 50mm x 47 mm made out of 5 mm plain colour PVC sheet reinforced with Mild Steel square tube, suppling & fixing in opening as per drawing complete all as specified and directed.

Supply and fixing of factory made single extruded WPC (Wood Polymer Composite) solid decorative type flush door shutter of size 30mm thick comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant. WPC to be laminated with PVC foil of minimum 14 microns thick of approved design pasted with hot melt adhesive on both faces of shutter and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all complete all as specified and as directed.Note: stainless steel butt hinges and necessary S.S screws shall be paid separately.

Supply and fixing Factory made solid panel wire guage PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and prelam PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling wii be wire guage. The wire guage shall be wrappedon an additional square 8 mm MS solid tube.This tube shall be welded to MS tube. The wire guage shall be stretched to tighten firmly, suppling & fixing in the frame at site as per specification & drawing

Material and labour for Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of MS tubes for top & bottom rails. MS frame shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheet strip of 20 mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in MS frame welded/sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, supplying & fixing in the frame at site as per specification & drawingcomplete all as specified and directed.

Supply and fixing Powder Coated Anodised aluminium frame for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc. Including taking down exsiting door/window fream with shutter complete all as specified and directed.

Materials and labour for Mild Steel framed work such as grills, gratings, etc., with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe-290(Gde E-165) including taking dwon old one complete all as specified and as directed.

Material and labour for power coated anodised aluminium door shutters, aluminium section weighing 1.00 Kg/ m (minimum) thickness not less than 2.00 mm including necessary joining cleats,glazing clips, ruber neoprene packing, handles 2 Nos in each door, floor hinges, anodised aluminum snap beading screws etc. Complete all as specified and as directed.

Material & labour of power coated aluminium 18 mm width, three track sliding window with shutters made of 1.5mm thick aluminium section for bottom track (1.28 kg/m min) & top , side track of shutter side vertical frame of 1.5mm thick(minmum) , shutter to be interlocking with vertical frame including necessary jointing cleats, glazing clips, rubber neoprene packing, roller, locking arrangement, handles 2 Nos , anodised aluminium snap beading screws etc. Complete all as specified. Complete all as specified and as directed.Note Nos :- (i) All window member including fitting & fixture i.e frame, track, shutter frame, etc shall be deem to included quoted rate. Only measure opening size of window.(ii) The drawing of window shall be approved by the GE prior to incorporation in the work.(ii) Only Glass for door shall be measure and paid separately under relevant items of BOQ .

Material and labour for power coated aluminium casement window and ventilator shutters, side hung type without sash bars, side hung type without sash bars, aluminium sections weighing 0.55 Kg/m (minimum) and thickness of member/section not less than 1.50 mm including necessary joining cleats, glazing clips, rubber packing, anodized aluminium snap beading, screws, anodized aluminium fittings such as peg stays 150 mm long (1 No.), hinges type B-21 100 mm long (2 Nos.) suitable handle (1 No.) complete all as specified and as directed.

Supply and fixing of sheet glass 4.8 mm thick ordinary quality fixed to aluminum door & window in squares in each pane of required size complete all as specified and as directed.

Supply and fixing of sheet glass 3.0 mm thick ordinary quality fixed to aluminum door & window in squares in each pane of required size complete all as specified and as directed.

Supply and fixing of glazing with sheet glass (frosted on one side) 4 mm thick ordinary quality with silicon putty in square not exceeding 0.5 Sqm in each pane. complete all as specified and as directed.

Supply and fixing of Butt hinges Stainless steel 100 mm size complete all as specified and directed.

Supply and fixing of Butt hinges Stainless steel 75 mm size complete all as specified and directed.

Supply and fixing of Aluminium anodised barrel tower bolts of extruded section size 150 mm complete all as specified and directed.

Supply and fixing of Aluminium anodised barrel tower bolts of extruded section size 200 mm complete all as specified and directed.

Supply and fixing of Aluminium anodised barrel tower bolts of extruded section size 75 mm complete all as specified and directed.

Supply and fixing of Aluminium handles cast type anodised 150 mm size complete all as specified and directed.

Supply and fixing of Aluminium handles cast type anodised 100 mm size complete all as specified and directed.

Supply and fixing of brass polish bright handles cast type anodised 100 mm size complete all as specified and directed.

Supply and fixing of Aluminium anodised sliding door bolt, with hasp & staple (bolt type) and fixing clips of sheet, cast of extruded sections and fixing bolts and sliding bolts of extruded sections 300 mm long .complete all as specified and as directed.

Supply and fixing of stainless steel telescopic ball bearing drawer channel of size 250mm x 46mm x 12.7mm, width of flap 30mm for modular kitchen. complete all as specified

Supply and fixing in repairs of double action brass bright polish floor spring hydraulically regulated made up of brass and fixed complete as specified and as directed.

Supply and fixing in repairs Door closure hydraulically regulated, designation no 1, universal type, suitable for door shutters of 700 mm in width and of weight not more than 35 Kg of aluminium (die cast) body complete all as specified and directed.

Supply and fixing 40 mm dia, cupboard knobs fixed with nut, screw and washer of brasscomplete all as specified and directed.

Supply and fixing in stainless steel Pet set of 6 complete all as specified and directed.

Supply and fixing in Hasp and staple 100 mm size, safety type, aluminium anodised with mild steel hinge pin including bolt to bright hinge plate and fixed with screws complete all as specified and directed.

Supply and fixing brass mortice lock vertical type, 6 lever, size 100 mm complete all as specified and directed.

Supply and fixing of brass locks, drawer, grade I, size 50 mm complete all as specified and directed.

Material and labour for Floor door stopper of SS body and tongue, anodised, with hard drawn steel spring of size 150 mm, fixed in floor complete all as specified and directed.

Supply and fixing wooden with stainless steel fancy type curtain brackets complete all as specified and directed.

Supply and fixing of drapery rod made of electric resistance welded MS pipe of 21mm dia having a coating of corrugated virgin PVC extrusion and cover with ABS plastic complete all as specified and directed.

Supply and fixing of Stainless steel wire cloth, 0.36mm nominal dia of wire and avergae width of aperture 1.00 mm and fixed with stainless steel wire staples complete all as specified and directed.

Supply and fixing in repairs Stainless steel wire cloth, 0.36 mm nominal dia of wire and avergae width of aperture 1.00 mm and fixed with stainless steel wire staples complete all as specified and directed.

Material and labour for 18/19 mm thick plywood, grade BWR, type BB fixed with screws to timber frame work complete all as specified and directed.

Material and labour for 12 mm thick plywood, grade BWR, type BB fixed with screws to timber frame work complete all as specified and directed.

Material and labour for 06 mm thick plywood, grade BWR, type BB fixed with screws to timber frame work complete all as specified and directed.

Material and labour for 0.9 mm thick decorative laminate type 1, of surface finish, colour and pattern as approved by GE, fixed with approved adhesive as per manufacturer's instructions over plywood. complete all as specified and directed.

Material and labour for Painting 2 coats of synthetic enamel paint on wooden surfaces of any description over 10 cm in width or girth including preparation new surface and one coat of pink primer complete all as specified and as directed.

Supply and fixing of 15mm bore galvanised steel tubes, medium grade with all fitting and fixed to walls, ceiling, floors and including taking up old GI pipe complete all as specified and as directed.

Supply and fixing of 20mm bore galvanised steel tubes, medium grade with all fitting and fixed to walls, ceiling, floors and including taking up old GI pipe complete all as specified and as directed.

Supply and fixing of 25mm bore galvanised steel tubes, medium grade with all fitting and fixed to walls, ceiling, floors and including taking up old GI pipe complete all as specified and as directed.

Supply and fixing of 15mm bore angle valve type cast copper alloy chromium plated screwed down high pressure with crutch or butterfly handle screwed both ends for iron pipe for union 15mm complete all as specified and directed.

Supply and fixingg in repair of bib cock cast copper alloy screwed down with long body with wall flange, and fixed for 15 mm bore GI tube pipe and all accessories complete all as specified and as directed. complete all as specified.

Supply and fixingg in repair of chromium plated pillar cock cast copper alloy screwed down with long body with wall flange, and fixed for 15 mm bore GI tube pipe and all accessories complete all as specified and as directed. complete all as specified.

Supply and fixing of vitreous china wash basin white flat back, size 550 x 400 mm including CP waste coupling, CP bottle trapwith GI pipe brackets & , rag bolt in cement concrete/brick wall and including taking down existing HWB and making good wall surface complete all as specified and as directed.

Supply and fixing of Vitreous china wash down water closet (pedestal pattern) with concealed S-trap or P-Trap, white, 390 mm high, seat cover including connection to drain (or outgoing pipe) and to flushing pipe, antisyphonage pipe etc and including taking down existing one complete all as specified and as directed

Supply and fixing as in repair of PVC low level flusing cistern 10 litres capacity white with ball valve & brackets with flush pipe complete all as specified and as directed.

Supply and fixin of in repair Plastic water closet seat, and cover white , closed pattern with flat bottom, and cover and mild steel chromium plated or aluminised hinging device etc complete all as specified and as directed by Engineer-in-Charge

Supply and fixing as in repair of PVC connections 15 mm size with PTMT nuts of length 450 mm complete all as specified and as directed.

Supply and fixing as in repair of PVC connections 15 mm size with PTMT nuts of length 600 mm complete all as specified and as directed.

Supply and fixing of Gratings made from Stainless steel Gr 304 of doom type & 127mm dia complete all as specified.

Supply and fixing in repairof Towel Rail 600 mm long of chromium plated fixed with and including chromium plated brass screws and wooden/plastic cleats complete all as specified and as directed.

Supply and fixing in repairof Towel ring of chromium plated fixed with and including chromium plated brass screws and wooden/plastic cleats complete all as specified and as directed.

Supply and fixing in repair of 125 mm dia of shower rose with 225 mm long arms, cast copper alloy chromium plated , swivel joints and fixed for 15 mm bore GI tube pipe and all accessories complete all as specified and as directed. complete all as specified.

Supply and fixing of Supply and fixing in repair of stainless steeel of 304 grade of kitchen sink with drain board of overall size 915mmx460mm and bowl size 410mm x330mmx160mm depth or equivalent made of 1mm thick stainless steel sheet with 32mm bore CP waste coupling including ball and chain 300mm long with bass cap rubber plug, 32mm bore PVC waste pipe (heavy duty) 90cm long, and bedded in cement mortar and fixed in CP cantilever brackets. complete all as specified and directed.

Supply and fixing of in repair Kitchen stainless steel plate rack (24" x24" x10") including necessary fixing / fittings & making good the existing surfaces complete all as specified and directed.

Supplying, hoisted and fixed in position of rotational moulded polyethylene water storage tanks in double layers and cylindrical vertical type with manhole lids(closed top) of 1000 litres capacity with ISI marked and all as specified in IS 12701 complete all as specified and directed .

Supply and fixing of PVC ball valve for 20 mm dia GI pipe all complete complete all as specified and directed.

Supply and fixing as in repair of health faucet of ABS body with wall hook and including one metre long stainless steel braided rubber hose pipe fixed on 15 nn dia angle cock all complete complete all as specified and directed

Supply and fixing of brass chromium plated superior quality single lever tall boy basin mixer 15 mm dia with 150mm extension body & 600mm long braided hoses complete all as specified and directed.

Supply and fixing of in repair 15mm bore, chromium plated two way bib taps cast copper alloy with crutch or butterfly handle screwed down for iron pipe complete all as specified and directed.

Supply and fixing in repairs 15 mm dia brass CP fancy wall mixer & connection to exposed shower pipe (SHA-1211NH & SHA-1213) & hand shower with connecting legs & wall flanges including hand shower with fiexble shower tube1.5m long for mixing hot & cold water screwed down for iron pipe and fixed as in repairs complete with hand shower rose and tube complete all as specified and directed.

Supply and fixing of tumbler holder chrome plated complete all as specified and directed.

Supply and fixing of Soap dish chrome plated complete all as specified and directed.

Supply and fixing of brass CP Bottle Trap 32mm for Wash Basin with inlet and outlets screwed for pipe or connections including necessary packing, union and cap complete all as specified and directed.

Supply and fixing of Towel shelf/rack chrome plated 24’’ long complete all as specified and directed.

Supply and fixing of Glass shelf chrome plated 22" long complete all as specified and directed.

Supply and fixing of corner glass shelf chrome plated 22" long complete all as specified and directed.

Taking down eaves gutters and rain water pipes (any size or pattern, including all fittings, heads, shoes, bends, swan-necks, etc. including removal outside MD land. (measured overall as fixed along the centre line over fittings and accessories).

Material & labour of Cast iron soil, rain water pipe, spun pipe, 150 mm bore in any length with or without ears with cement joints fixed on walls and including taking down existing wast pipe line all as specified & directed.

Material & labour of Cast iron soil, waste and vent pipe, spun pipe, 100 mm bore in any length with or without ears with cement joints fixed on walls and including taking down existing wast pipe line all as specified & directed.

Material & labour of CI (Spun) bends for 150 mm bore pipe.(any storey)complete all as specified and as directed.

Material & labour of CI (Spun) bends for 100 mm bore pipe.(any storey)complete all as specified and as directed.

Material & labour of CI (Spun) Branch pieces, single (equal or unequal) for 150 mm bore pipe.(any storey)complete all as specified and as directed.

Disconnecting existing tanks, setting aside (or lowering if required) for repairs, cleaning, etc. and hoisting if required reconnecting and re-fixing in position including cleaning and removing all scales, dirt etc. from the tank and from mouths of circulating pipes etc., exceeding 250 litres but not exceeding 500 litres capacity complete all as specified and as directed.

Disconnecting existing tanks, setting aside (or lowering if required) for repairs, cleaning, etc. and hoisting if required reconnecting and re-fixing in position including cleaning and removing all scales, dirt etc. from the tank and from mouths of circulating pipes etc., exceeding 500 litres but not exceeding 1000 litres capacity complete all as specified and as directed.

Disconnecting existing tanks, setting aside (or lowering if required) for repairs, cleaning, etc. and hoisting if required reconnecting and re-fixing in position including cleaning and removing all scales, dirt etc. from the tank and from mouths of circulating pipes etc., exceeding 1000 litres but not exceeding 2000 litres capacity complete all as specified and as directed.

Providing and injecting chemical emulsion for post constructional antitermite treatment along external wall where the apron is not provided using chemical emulsion at the rate of 7.5 litres per sq.m of the vertical surface of the sub-structure to a depth of 300mm including excavating channel along the wall and rodding etc. complete all as specified and as directed by Engineer-in-charge.

Providing and injecting chemical emulsion at points of contact of wood work by chemical emulsion (in oil or kerosene based solution) @ 0.5 litre/hole by drilling 6mm dia holes at a downward angle of 45 degree at 150mm centre to centre and sealing the same complete all as specified and as directed.

Providing and injecting chemical emulsion at of voids in masonry using chemical mulsion one litre per hole, at 300mm intervals including drilling holes at 45 egree and replugging them with ement mortar 1:2 (1 cement : 2 coarse and) to match the existing floors complete all as specified and as directed.

Chipping of unsound /weak concrete materials including cover plaster from RCC structural member i.e. slabs ,lintel,chajja, fin , facia etc. 25 mm average thickness including tapering all edges, making square shoulders of cavities air and cleaning of exposed concrete surface of lightly picking materials by manual method including foreign materials , loose concrete/aggregate etc and disposal of all debris out side of MOD land and complete all as specified and as directed.

Removing of concrete all around reinforcement bar upto 12 mm dia from behind the reinforcing bars average 25mm (but not less than 15mm air gap)by manual methods (using wire brushing ,chiselling etc) and applying chloride free rust removing chemical on rusting steel reinforcement bar and removing all rust from steel reinforcement bar by emery paper and cleaning the area throughly by water and allow it to dry and totally rust free of reinforcement bar and applying two component epoxy zincrich primer on existing reinforcement surface afer aplication of rust remover of minimum specific gravity 1.75, adhesive bond strength with steel is 1.50N/mm2 and maximum coverage area 5.00 Sqm per litre all as complete as per manufacturer's instruction as specified and as directed

Material and labour for introducing new reinforcement bars upto 12 mm dia for structural connection in RCC beams, columns, lintel and slabs including power drilling holes of appropriate diameters in reinforced or plain cement concrete to a minimum depth of 150mm and upto 200mm including power drilling,fixing the reinforcement in position using epoxy, cleaning of loose dust by blowing air, sealing with epoxy cartridges etc all as specified and directed.

Material and labour for two component structural grade polymer modified reinstatement mortar of compressive strength, flexural strength shall not be less than 45 MPa at 28 days , 7MPa at 28 days respectively ( maximum coverage area 1.3 sqm per 25 kg pack @ 10 mm thickness) over a coat of epoxy Bonding agent on existing surface for strengthening of beams, columns & other structural elements of average thickness 25mm and morter shall be applied in layers n.exc 6mm thick in layers and including surface preparation as per manufacturers instruction complete all as specified and as directed.(Any storey/ height of building/ structure)Note:- This item shall be execution where shuttering is not possible or small patch repairs of structural elements .

Material and labour for wire netting of stainless steel wire 1.4 mm dia fixed with tinned tacks with and including annealed mild steel wire not less than 0.9mm dia or fixing with galvanised steel staples complete all as specified and as directed.

Supply and fixing rubber gasket of size 50mmx6mm suitable for air sealing of aluminium /wooden door & window complete all as specified and directed.

Subtotal of Sch A part-I

SCHEDULE 'A' PART - II FOR E/M PORTION

Taking down carefully unserviceable copper / aluminium point wiring (light, fan, bell socket or power) including all fittings such as switches, socket, ceiling roses , regulators and switch boxes etc complete and making good the disturbed surfaces complete all as specified and as directed.

Material and labour for point wiring with 1.5 Sq. mm (nominal area) PVC insulated and sheathed single core FRLSHcopper cable 1100 volts grade with stranded copper conductor in and including PVC rigid concealed conduit (heavy grade) and conduit accessories alongwith continuous earth wire 1.5 Sq mm PVC insulated and sheathed single core FRLSH cable 1100 volts grade with stranded copper conductor and connected to common earth dolly complete for one light/fan point controlled by one switch complete all as specified and as directed.Note:-Flush steel terminal box, inner plate and front plates shall be measured and paid seperately.

Material and labour for Point wiring with 1.5 Sq. mm (nominal area) PVC insulated and sheathed single core FRLSHcopper cable 1100 volts grade with stranded copper conductor in and including PVC rigid concealed conduit (heavy grade) and conduit accessories alongwith continuous earth wire 1.5 Sq mm PVC insulated and sheathed single core FRLSH cable 1100 volts grade with stranded copper conductor and connected to common earth dolly complete for modular one socket outlet 5 pin 6 amps on independent board complete all as specified and as directed.

Material and labour for Point wiring with 1.5 Sq. mm (nominal area) PVC insulated and sheathed single core FRLSH copper cable 1100 volts grade with stranded copper conductor in and including PVC rigid concealed conduit (heavy grade) and conduit accessories alongwith continuous earth wire 1.5 Sq mm PVC insulated and sheathed single core FRLSH cable 1100 volts grade with stranded copper conductor and connected to common earth dolly for one 5 amps socket outlet on same board with other switch complete all as specified and as directed.

Materials and Labour for Point wiring with 2.50 Sq. mm (nominal area) PVC insulated and sheathed single core FRLSHcopper cable 1100 volts grade with stranded copper conductor in and including PVC rigid concealed conduit (heavy grade) and conduit accessories alongwith continuous earth wire 4.00 Sq mm PVC insulated and sheathed single core FRLSH cable 1100 volts grade with stranded copper conductor and connected to common earth dolly complete for modular one socket outlet 5 pin 16 amps on independent board complete all as specified and as directed.NOTES FOR ITEM NO 158 to 161- Flush steel terminal box, inner plate and front plates shall be measured and paid seperately.

Material and labour for Metal flush box 3 module complete all as specified and as directed.

Material and labour for Metal flush box 4 module complete all as specified and as directed.

Material and labour for Metal flush box 6 module complete all as specified and as directed.

Material and labour for Metal flush box 8 module complete all as specified and as directed.

Material and labour for Metal flush box 12 module complete all as specified and as directed.

Material and labour for White cover plate with frame (both ineer plate & outer plate cover) ,3 module complete all as specified and as directed.

Material and labour for White cover plate with frame (both ineer plate & outer plate cover) , 4 module complete all as specified and as directed.

Material and labour for White cover plate with frame (both ineer plate & outer plate cover) , 6 module complete all as specified and as directed.

Material and labour for White cover plate with frame (both ineer plate & outer plate cover) , 8 module complete all as specified and as directed.

Material and labour for White cover plate with frame (both ineer plate & outer plate cover) , 12 module complete all as specified and as directed.

Material and labour for Modular switch 6 Amp single pole one way complete all as specified and as directed.

Material and labour for Modular switch 16 Amp single pole one way complete all as specified and as directed.

Material and labour for Modular socket 16/6 Amp 3 pin combined shattered complete all as specified and as directed.

Material and labour for Modular socket 6 Amp 2/3 pin combined shattered complete all as specified and as directed.

Material and labour for Electronic type fan regulator step type 120 watt, 230 volt complete all as specified and as directed.

Material and labour for Modular bell push 6 Amps single pole one way complete all as specified and as directed.

Material and labour for Blanking plate SP with incoming contact complete all as specified and as directed.

Supply and fixing ceiling rose surface bakelite 65x50mm three terminals complete all as specified and as directed.

Supply and fixing of 4 module MCB protected power unit for Air conditioner with MCB double pole 16-25 Amp, Starter Unit 16-25 Amp and socket 16-25 Amp with plug top complete all as specified and directed

Supply & Fixing of LED street light fitting ( Building Security light) of 35Watt with LED lamp’s & driver and made of pressure die-cast aluminum housing, IP 65/IP 66 road way luminaries with UV stabilized polycarbonate cover or toughen glass cover & high power LED’s as light source with 110 Lumen per watt and electronic driver with efficiency > 85% . The light fitting shall be fixed on wall/pole with and including 25 mm dia( or higher size as per manufacturers recommendation) light grade GI pipe (bend to shape or as per manufacturers recommendation ) bracket 1.5 mtr long complete with MS flat iron clamp (clamps shall be 40 x 5 mm MS flat) nuts, bolts & washers including painting the clamps with two coat of aluminium paint over a coat of red oxide primer and including taking up old light fitting complete all as specified and as directedNotes : GI pipe bracket and clamps shall be deem to be included above quoted rate..

Supply and fixing ceiling fans complete with blades, down rods, electronic regulator and accessories, 230 V, 1200 mm sweep. Min air delivery 210 CFM with service value 6.00 BEE. Five star rated with brushless direct current motor (BLDC) and necessary connecting PVC insulated Flexible cable for connection from ceiling rose to fan and connecting including taking dwon old one and remove to MES store yardcomplete all as specified.

Supply and Fixing exhust fan 240V, 300mm sweep, 900 RPM , MS body, highly efficient heavy duty motor with pressure die cast aluminium rotor mounted on two ball bearings and conforming to IS: 2312 and including aluminium lowers and shutters fixed to wall , writing the MES fan numbers with paint and 0.75 Sqmm , 3 core PVC insulated Flexible copper cable for connection from ceiling rose to fan complete all as specified and as directed.

Supply and fixing of sheet metal enclosure for MCBs to be used singal pole & nutral double door 8 Way 200 Amps rated busbar and including fixed with 25mm x 6 mm mild steel clamp of suitable length and including taking up old onet fitting complete all as specified and as directed.

Supply and fixing of sheet metal enclosure for MCBs to be used singal pole & nutral double door 4 Way 200 Amps rated busbar and including fixed with 25mm x 6 mm mild steel clamp of suitable length and including taking up old onet fitting complete all as specified and as directed.

Supply and fixing of sheet metal enclosure for MCBs to be used triple pole & nutral double door 8Way 200 Amps rated busbar and including fixed with 25mm x 6 mm mild steel clamp of suitable length and including taking out old DB complete all as specified and as directed.

Supply and fixing of sheet metal enclosure for MCBs to be used triple pole & nutral double door 4Way 200 Amps rated busbar with MCCB provision (vertical type) and including fixed with 25mm x 6 mm mild steel clamp of suitable length and including taking out old DB complete all as specified and as directed.

Supply and fixing MCCB four pole 100 amps 415 volts 16KA breaking capacity.

Supply and fixing MCB four pole 40 to 63 amps 415 volts 10KA breaking capacity.

Supply and fixing of MCB SP of rating 6 to 32 Amps 240 V complete all as specified and as directed.

Supply and fixing MCB DP 40 to 63 amps 240 volts 10KA breaking capacity complete all as specified and as directed.

Supply and fixing of sub main wiring with four single core 10.0sqmm (nominal area) PVC insulated copper conductor FRLSH, multi stranded, unsheathed 1100 volts grade IS-694 marked in PVC double lock casing caping and accessories accessories including two single core 10.0 sqmm copper conductor cable FRLSH as earth wire and including taking out old sub-main wiring complete all as specified and as directed.NOTE:- (a) All runs of copper conductor and one run of conduit shall be measured as one run length.

Supply and fixing of sub main wiring with two single core 6.0sqmm (nominal area) PVC insulated copper conductor FRLSH, multi stranded, unsheathed 1100 volts grade IS-694 marked in PVC double lock casing caping and accessories accessories including one single core 6.0 sqmm copper conductor cable FRLSH as earth wire and including taking out old sub-main wiring complete all as specified and as directed.NOTE:- (a) All runs of copper conductor and one run of conduit shall be measured as one run length.

Supply and fixing of sub main wiring with two single core 4.0sqmm (nominal area) PVC insulated copper conductor FRLSH, multi stranded, unsheathed 1100 volts grade IS-694 marked in PVC double lock casing caping and accessories accessories including one single core 4.0 sqmm copper conductor cable FRLSH as earth wire and including taking out old sub-main wiring complete all as specified and as directed.NOTE:- (a) All runs of copper conductor and one run of conduit shall be measured as one run length.

Material & Labour for earthing with galvanised steel earth plate electrode of size 60cmx60cmx6mm thick buried directly in ground (earth pit not less than 2.25m deep below the ground level) with top edge of the plate not less than 1.5m below normal ground level, connected to the galvanised earth lead by means of bolts, nuts check nuts and washers of galvanised iron using GI 4 mm dia wire as earthing lead as shown in electrical plate No. 3 of SSR Part-I connected to earthing test point all as specified or indicated including testing on completion including necessary excavation and earth work in soft/loose soil, returning filling, disposal of surplus soil, earth pit in PCC 1:3:6 type C-1 using 20mm graded stone aggregate pit, funnel, 20mm dia GI medium grade watering pipe, 40mm dia GI medium grade earth lead protection pipe, CI frame and cover, wire, copper lugs etc mesh, chorcoal and common salt in alternatee layer complete all as specified and directed .

S&F in repair of LED Bulk Head fitting 1 x 10W with inbuilt driver, IP 65 protection, 2.5 KV grade elegantly made diffuser and housing of engineering plastic including connecting up with three core flexible copper conductor cable complete all as specified and as directed

S&F LED tube light fitting 1 x 25W, 220V, AC decorative box type with driver, holder including LED tube light with polycarbonate housing and diffuser with protection of IP-66 connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete all as specified and directed by Engineer-in-Charge.

S&F in repair LED weather proof tube light fitting 1 x 18W, worm with mounted on wall / ceiling connected with insulated unsheathed flexible copper wire of suitable size from ceiling rose complete all as specified and directed by Engineer-in-Charge.

S&F LED decorative wall lights of Mouth blown glass fitting 8W x 2, complete with all accessories internally pre-wired and including connecting up with twin core twisted flexible copper conductor cable 2 LT wall lamp opal glass with chrome finish lamp B-22 LED 8W x 2 complete all as specified and directed by Engineer-in-Charge.

S&F in repair adjustable bed side LED lamp with clear lens with color temperature 3000 K suitable upto 4W metal and synthetic material lumen 150 lm including connecting up with twin core twisted flexible copper conductor cable complete all as directed by Engineer-in-Charge

Taking down / re fixing of water heater any type complete with all accessories such as safety valve, thermostat, NRV, connection pipe etc as directed by Engineer-in-Carge.

Note: Schedule of credit amount shall be deducted from the total quoted amount of BOQ.

S.M.CONSTRUCTIONS (BID ID -3136666)