SPECIAL REPAIR TO BUILDING NO T13 1, T13 2 AND T13 3 AT GNC LINE, SPECIAL REPAIR TO SEWAGE LINE AT MT WING AND PROVN OF DEEP FREEZER AT ASC CENTRE SOUTH UNDER AGE BR II OF GE CENTRAL BANGALORE

Amount

Excavation in trenches n.exc 1.5 m wide and n.exc 1.5 m in depth for foundation, etc area not exceeding 10 Sqm on plan and getting out in soft/loose soil complete all as specified and directed.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm as in soft/loose soil complete all as specified and directed.

Removing excavated material to a distance not exc. 50 m and depositing where directed at a level not exc 1.5 m above the starting point complete all as specified and directed.

Demolition of plain cement concrete (unreinforced) any description and in any position not otherwise specifically provided for etc complete including removing the materials out side MD land complete all as specified and directed.

Demolition of plain cement concrete (unreinforced) in ground floors, plinth protection/path/pavings etc not exceeding 15 cm thickness. (below or above ground level) and removing debris outside MD land complete all as specified and directed.

Demolition of brick work or stone/boulder masonry, built in cement mortar including all quoins, arches, pillars etc and removing debris outside MD land complete all as specified and directed.

Taking down chowkats or frames, exceeding 1.5 but n.exc. 4 Sqm in each with shutter (without taking off shutter from the frame) complete all as specified and directed.

Taking down chowkats or frames, exceeding 1.5 but n.exc. 4 Sqm in each with shutter (without taking off shutter from the frame) complete all as specified and directed.

Dismantling Asbestos Cement Corrugated or Semicorrugated in Roof covering .

Dismantling timber scantlings 40 Sq.cm and over in section (unframed work), in any position complete all as specified and directed.

Taking down cement plaster on brick or stone walls etc including racking out joints, hacking for key, scrubbing down with water and removing debris outside MD land complete all as specified and directed

S & F well seasoned 2nd class hard wood plain, solid, straight chowkat and frames, wrought, framed, rebated on the solid rounded or chamfered, put together with glue pinned at joints including treating the timber libarally brushed at least twice with oil or kerosene based solusion of chlorophyrifos 20EC 1.0 % (by weight) concentration complete all as specified and as directed.

Demolition and breaking of 100 to 200mm bore drain pipe (Salt glazed stonewar, AC, RCC) set in cement mortar complete all as directed.

M & L for Sand filling for cushioning under sewage pipe complete all as specified and directed.

Supply and fixing underground Double Wall Corrugated (DWC) pipe, 100mm nominal size (ID 98.00mm & OD 116.00mm), SN- 4, in any length, with rubber ring joints including all fittings, conforming to IS- 16098 (Part- 2) , laid in trenches and testing on completion complete all as directed.

Supply and fixing underground Double Wall Corrugated (DWC) pipe, 150mm nominal size (ID 148.50mm & OD 172.50mm), SN- 4, in any length, with rubber ring joints including all fittings, conforming to IS- 16098 (Part- 2) , laid in trenches and testing on completion complete all as directed.

Supply and fixing underground Double Wall Corrugated (DWC) pipe, 200mm nominal size (ID 197.40mm & OD 230.50mm), SN- 4, in any length, with rubber ring joints including all fittings, conforming to IS- 16098 (Part- 2) , laid in trenches and testing on completion complete all as directed.

M & L for cement concrete 1:3:6, type C1 as in kerb or mud stop, rounded or chamfered on edges complete all as directed.

M & L for Plain cement concrete 1:3:6, type C-1, (using 20 mm graded stone aggregate) as in surface channels and drains including necessary form work complete all as specified and directed.

M & L for extra for forming fair finished to concrete surface of drain 30cm inner girth in cement including forms, mould, mitred/stopped etc complete all as specified and as directed.

M&L for machine cut cudappah stone slab as in flooring, 20 to 25mm thick laid and and jointed in grey neat cement slury and pointed in coloured cement to match with the shade of the stone slab including providing 20mm thick screed bed in CM 1:4 including rubbing, polishing complete all as directed.

M & L for roundings to edges of stone slabs, one edge, as in steps, cooking platform and other similar situation complete all as directed.

M&L for precast cement concrete block masonry type C1, 1:3:6 (20 mm graded granite stone aggregate) with solid blocks, exc 10 cm in width and setting in cement mortar 1:6 complete all as specified and directed.

M & L for Plain cement concrete 1:2:4, type B-1, (using 20 mm graded stone aggregate) as in coping, kneelers, bed plates etc including weathering slightly rounded or chamfered angles including necessary form work complete all as specified and directed.

M & L for Plain cement concrete 1:4:8, type D-2 (using 40 mm graded stone aggregate) as in foundation, filling and mass concrete, etc complete all as specified and directed.

M & L for Plain cement concrete 1:2:4, type B-1 (using 20 mm graded stone aggregate) as in benching including finished the top surfaces even and smooth using extra cement complete all as specified and directed.

M & L for 75mm thick Plain cement concrete 1:4:8, type D-2 (using 40 mm graded stone aggregate) as in sub base of floor, etc complete all as specified and directed.

M & L for 40 mm thick, plain cement concrete 1:2:4, type B-1 (using 20 mm graded stone aggregate) as in floors laid in panels, finishing the surfaces even & smooth with using extra cement complete all as specified and directed.

M & L for non-skid, matt finished, ceramic, coloured tiles, Grade B II(a), 8 to 10mm thick (square/rectangular) area of each tile exc 0.11 sqm but n.exc 0.18 sqm, in floors etc, including 15 mm thick screed bed in cement mortar 1:4 and set & jointed in neat cement slurry and pointed in white or coloured cement to match with the shade of tiles complete all as specified and directed.

M & L for glazed ceramic, coloured tiles, Grade B III, 7 to 8 mm thick area of each tiles not less than 0.06 sqm as in skirting including 10 mm thick screed bed in cement mortar 1:3 set & jointed in neat cement slurry and pointed in coloured cement to match with the shade of tiles complete all as specified and directed.

M & L for Vitrified ceramic, designed, coloured tiles, Grade B I(b), 10 mm thick, (square/rectangular) polished, area of each tiles exc 0.36 sqm but not exc 0.42 sqm, in floors, etc including 15 mm thick screed bed in cement mortar 1:4 and set & jointed in neat cement slurry and pointed in white or coloured cement to match with the shade of tiles complete all as specified and directed.

All as per item No 31 above/herein-before but in vertical surfaces including skirting, dados and risers to steps etc to match the length of floor tiles including 10 mm thick screed bed in cement mortar 1:3 and set & jointed in neat cement slurry and pointed in white or coloured cement to match with the shade of tiles complete all as specified and directed.

M & L for Hardcore of broken/crushed stone aggregate of gauge n.exc 63 mm deposited, spread and levelled in layers not exc 15 cm thick, watered and rammed to a true surface complete all as specified and directed.

M & L for precast chequered cement concrete tiles of size 30cm x 30cm x 20mm thick, as in floors etc, including 15 mm thick screed bed in cement mortar 1:4 and set & jointed in neat cement slurry and pointed in grey cement and pigments to match with the shade of tiles complete all as specified and directed.

M & L for plain cement concrete 1:3:6, type C-1 (using 20mm graded stone aggregate) for embedding holdfast, bed block, cills, etc including necessary form work complete all as specified and directed.

S & F Mild steel small articles using flat iron such as band, strap, hold fast, cleat, support, hook, hinges, base tie for door frame etc and other similar items conforming to Fe-290, Gde E-165 including retaining with tar or coat tar black paint complete all as specified and as directed.

S & F box type powder coated steel windows/ventilators double side shutters ie glass and wire mesh shutter, including pressed steel frames made out of CRCA sheet of 80X60X1.25mm thick double rebated, shutters box type made out of CRCA sheet of 40X20X1.0mm thick, 12mm square guard bar/grill welded to steel frame, window shutters side hung, ventilator shutters top hung, box type hinges, aluminium die cast handles for glass shutters, iron flat type handles for mesh shutters, telescopic stays etc complete all as specified in TD drawing No TD/539 dated 09.02.2004 of Chief Engineer Chennai Zone and as directed. NOTE:- (i) Qouted rate under this item shall deemed to be inclusive of steel frame, both side steel shutters, guard bars/grills, handles, stays, beading/fillets for fixing glass/wire mesh including cost elements for fixing of glass & wire mesh and mearurement/ pament shall be considered as one unit by comprising all these elements. (ii) Glass and wire mesh shall be measured and paid as supply only underseparately under respective item.

S & F factory made solid moulded PVC door shutter 28 to 30 mm thick (style) with 2, 4 or 6 raised panel design with particle board core and 2mm thick moulded PVC sheet on the front face & 2mm plain colour PVC sheet on back face all as per specification and drawing and as directed.

S & F solid PVC door frames of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with MS square tube complete all as specified and directed.

S & F factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of MS tubes for top & bottom rails. MS frame shall be covered with heat moulded, plain colour PVC 'C' channel having a PVC sheet strip of 20 mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail, panelling of plain colour PVC sheet 5mm thick to be fitted in the MS frame welded/sealed to the stiles & rails with suitable PVC sheet beading and jointed together with solvent cement, as per specification and drawing and as directed.

S & F 100 mm size, butt hinges, stainless steel with cadmium coated screws complete all as specified and directed.

S & F 150 mm long, Aluminium, barrel tower bolts of extruded section of aluminium alloy, anodised finish not be less than Grade AC 10 of IS 1868:1996 with transparent anodic film complete all as specified and directed.

S & F 150 mm size, Aluminium handles, cast type, anodised to a bright natural, mat finish not be less than Grade AC 10 of IS 1868:1996 complete all as specified and directed.

S & F aluminium alloy anodised sliding door bolt with hasp & staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy, length of bolt of 300 mm anodised finish not be less than Grade AC 10 of IS 1868:1996 complete all as specified and directed.

S&F aluminium anodised body and tounge door stopper with hard drawn steel spring, 140mm size fixed to door all as directed.

S & F brass chromium plated tubular towel rail, 20mm dia 'D' type, 600mm long between flanges complete all as specified and directed. (Make: Parryware /Hindware/Cera/Prayag)

S & F brass chromium plated tubular towel rail, 20mm dia complete all as specified and directed.

S&F brass chromium plated curtain rod brackets all as specified and directed.

S&F in repair sinks with drainage board made of stainless steel lmm thick kitchen or laboratory with plugs,washers and wastes; including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 915mm x 460mmx203mm bowl size 405mm x 354mmx203mm (Make: Prayag Cat No 1239D or equivelent of Parryware /Hindware/Cera)

S & F steel chromium plated soap dish, approximate size 160X160mm fixed with screws complete as specified and directed. (Make: Parryware /Hindware/Cera/Prayag)

S & F swival shower of PTMT 15mm bore (minimum weight 40 gms) including shower arm 15mm size, 225mm long with bend of 45 degree with flange of PTMT any colour (minimum wt 40 gms) complete all as specified and directed. Make Prayag or equivelent as approved by GE

S & F stainless steel wall hanger of approved size fixed to wall/door all as directed.

S & F for false ceiling of 4mm thick designer ceiling board, pre-painted cement fibre board of size 595X595 mm of any texture (such as lake and hill, ocean, cascade or Electra) using GI snap grid system with rool formed out of hot dip galvanised steel capings (Powder coated finished) . The suspension system consisting of perimeter wall angle of size 24X24 mmX0.45mm of thick GI sheet to secure on wall portion fixed with the help of rawl plug @ 450mm centre to centre universal main runner of T shaped section with single rotary stitching of size (32X24mm) made from 0.33mm thick GI sheet of length 3.60 metre to be spaced @ 1200 centre to centre cross runner T shaped with double rotary stitching of size (30X24mm) of length 1200mm made from 0.25mm thick GI sheet spaced @ 600mm centre to centre (1200X600mm) of size module intermadiate T shaped cross runner of size (25X24mm) of length 600mm made of 0.25mm thick GI sheet to form (600X600mm) size of module including suspension of the ceiling from the roof/structural members, soffits angles, cleats, by using GI suspenders of 3mm dia GI wire and level adjusters including U clamp of GI fixed in ceiling all complete and making opening by cut out the ceiling board for ceiling light fittings as required and as per manufacturer's instruction or as directed by Eng-in-charge. Make :- Eternit Everest / lafarge/ Armstrong or equivalent as approved by GE

S & F 5.50 mm thick, sheet glass, ordinary quality and glazing with oil putty/timber beads in square not exceeding 0.5 Sqm in each pane complete all as specified and as directed.

S & F Rolled mild steel work as in trusses, purlins, rafter etc using Joist, channel, angle, or tee sections, fixed independently, without connecting plates, etc including cutting, welding complete. Steel section conforming to Fe-410-W (Gde-E-250) quality-B complete all as specified and directed.

S&F for pre-painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick (Total coated thickness) of any colour, finished with resin coat on both surfaces @ 150 gm/sqm of coating (total both surfaces) having tensile strength of 550 Mpa as in roof covering /cladding to wall, fixed with best quality self tapping screws as specified

M & L for Precast Reinforced Cement Concrete 1:2:4, type B-1 (using 20 mm graded stone aggregate) as in cover slab of drain, etc and set in cement mortar 1:4 including necessary form work, moulds, etc complete all as specified and directed by the Engr-in-Charge. (Note : Reinforcement shall be measured and paid separately)

S & F TMT steel bars 6 to 10mm dia, cut to length, bend to shape required, including cranking, bending spirally as in tie/stirrups of columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips complete all as specified and directed.

S&F for stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples, complete all as specified and directed

M & L for 75 mm thick, plain cement concrete 1:3:6, type C-2 (using 40mm graded stone aggregate) as in plinth protection laid in proper slope/gradient etc, finishing cement concrete surface even and smooth without using extra cement including making joints with bitumastic filing in proportion of bitumen and sand 1:2 complete all as specified and directed.

M & L for rendering 15 mm thick in cement mortar 1:4 on fair faces of brick masonry or concrete surfaces and finishing the surfaces even and smooth without using extra cement complete all as specified and directed.

M & L for rendering 15 mm thick in cement mortar 1:6 on other than fair faces of brick masonry or concrete surfaces and finishing the surfaces even and smooth without using extra cement complete all as specified and directed.

M & L for rendering 15 mm thick in two layer (10mm + 5mm thick) on fair faces of brick work or concrete surfaces in cement mortar 1:4, mixed with water proofing compound at top 5mm thick layer by weight of cement as per manufacturer's instructions and finished the surface even and smooth without using extra cement complete all as specified and directed. (Note : WPC shall be measured and paid separately against respective item).

"Supply only" liquid water proofing compound complete all as specified and directed. (Make : Dr FIXIT/Fosroc/choksey)

M & L for Preparation of newly plastered surfaces of walls and applying two coats of cement base paint over a coat of alkali resistant priming paint complete all as specified and directed.

M & L for preparing old plastered surfaces of walls by complete removal of existing treatment and applying two coats of cement base paint over a coat of primer complete all as specified and directed.

M & L for preparing newly plastered surfaces of internal walls, etc and applying two coats of distemper oil emulsion over a coat of primer including 1 to 2mm thick wall care putty complete all as specified and directed.

M & L for preparing old plastered surfaces of walls by complete removal of existing treatment and applying two coats of distemper-oil-emulsion over a coat of primer over a coat of wall care putty (1 to 2mm thick) complete all as specified and directed.

M & L for Preparation of new or previously untreated wood and wood based surfaces of any description, not otherwise described, over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and directed.

M & L for Preparation of new steel surfaces of any description, over 10 cm in width or girth, not otherwise described and applying two coats of synthetic enamel paint over a coat of red oxide, zinc chrome primer complete all as specified and directed.

S&F in Repair Vitreous China Squatting Pan"Orissa pattern" size 580 mmx440 mm white with integral foot rest S or P trap etc. & Provision of concrete bedding and making good to floor all as specified & directed by Engineer-in-charge. Make CERA Cat No COVINA S3010109 or equivelent of Prayag/Hindware/Parryware

S & F in repairs, 10 litre capacity, PVC valve less syphonic action type, 32mm dia flushing cistern, low level, white, with inlet, ball valve, flush pipe, float and handle brackets complete all as specified and directed. Make CERA Cat No B1010109 or equivelent of PRAYAG/HINDWARE/Parryware

S & F in repairs PVC connection pipe with PTMT nuts, 450mm long. Make: CERA/Hindware/Parryware/PRAYAG

Supplying and laying in repair 25mm dia gun metal gate valve with iron wheel head screwed both ends for iron pipe complete all as specified.

S & F in repair 15 mm bore, bib taps, cast copper alloy, chromium plated with capstan head, screwed down, screwed for iron pipe or for brass ferrule complete all as specified and directed.

S & F in repair 15 mm bore, concealed stop valves, fancy type with flange and shank, cast copper alloy, chromium plated with capstan head, screwed down, screwed for iron pipe or for brass ferrule complete all as specified and directed.

S & F 20 mm bore, stop valves, brass cast copper alloy, chromium plated with crutch or butterfly handle screwed down, screwed for iron pipe or for brass ferrule complete all as specified and directed.

S&F PVC bathroom mirror cabinet best quality of approximate size 430X330mm fixed to wall using brass screws complete all as directed. Make PRAYAG Cat No 551 or equivalent as approved by GE

S&F in repair plate rack made of stainless steel fixed to wall, size 900mmX 750mm X 250mm (36x31x10 ench) Make PRAYAG Cat No P-348 or equivelent of Nirali/Diamond

Taking up or down 20mm bore, Steel tubing and connections.

Supplying and laying of 20mm dia CPVC pipes (ISI marked) SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors complete all as specified.

S & F in repair 75 mm dia outlet , PVC (SWR) floor trap, with grating including jointing to waste pipe fixed in cement concrete type B-1 (1:2:4) complete all as specified and directed.

S & F in repair 125/110mm, PVC (SWR) gully trap, with grating including jointing to waste pipe with solvent cement, fixed in cement concrete type B-1 (1:2:4) complete all as specified and directed.

S & F 75 mm bore, UPVC (SWR), Type 'B', Soil waste and vent pipes in any length without ears, with solvent cement joints fixed to wall, using MS holder bat etc complete all as specified and directed.

Taking off covers and taking out sludge from septic tank/manholes/ chambers upto 1.50 metre depth (lift height) form GL by means of mechanical compressor/ sewage cleaning machine, cleaning the entire internal sewage with water including removing mud/sludge/liquid mud out side MD land and re-fixing the cover in position of any size of manholes complete all as directed by Eng-in-charge. Note :- (i) Mechanical compressor machine for sewage cleaning shall be arranged by the contractor at his own cost as and when required and as directed by the Eng-in-charge. No extra claim for bringing number of times as and required shall be antertained/admissible. (ii) Measurement shall be made in part or in full case to case basis whatever found at site. Contractor have not right to claim for taking out sludge/cleaning full volume of septic tank/manhole/chamber.

Taking down carefully unserviceable aluminium/copper point wiring (light, fan, socket or power) including unserviceable light fittings, switch board complete, switch sockets, ceiling roses, pendants, regulators, sockets, etc and removing materials from site and making good disturbed surfaces of walls, floors, etc complete all as specified and directed.

M & L for Point wiring surface type, with 1.5 Sqmm (nominal area), FRLS PVC insulated, multistranded, single core unsheathed, copper conductor cables passing through and including providing PVC casing caping/conduit 'medium grade' with all fittings and accessories (like Tee, bend etc.) complete in walls /ceiling etc. with and including 1.5 Sqmm (nominal area) FRLS, PVC insulated, unsheathed, stranded, single core, copper cable green in colour as earth continuity wire connecting to common earth point and earth dolly including MS/PVC terminal box with 3mm thick masonite laminated sheet top cover fixed on wall with suitable sizes cadmium plated iron screws and washers etc.for mounting switches, sockets, regulators etc complete for one light/fan/bell/buzzer point controlled by one ,one way switches complete all as specified and directed.

All as per item No 87 above but for one 3 pin socket outlet, 5 Amps on Independent board complete all as specified and directed.

All as per item No 87 above but for one 5 Amps, 3/5 pin socket outlet on the same board with other switches complete all as specified and directed.

All as per item No. 87 here in before but wiring with cables of size 2.50 sqmm for wiring & cables of size 2.50 sqmm both (FRLS) as continuous earth wire for one 15 Amps, 6 pin Switch/Socket outlet on Independent board complete all as specified and directed.

S & F switch piano, 5 Amp, single pole, flush type one way 230 volts complete all as specified and as directed.

S & F Switch socket combination, 2 in 1, 5 Amps (bearing ISI marked), flush type, 240 volts complete all as specified and directed.

S & F Switch socket combination, 5 in 1, 5/15 Amps (bearing ISI marked), 240 volts, flush type complete all as specified and directed.

S & F bell push button, flush type, single pole, 240 volts, one way complete all as specified and directed.

S & F buzzer/calling bell, Ding Dong type, AC 230 volts, single pole complete all as directed.

S & F Ceiling rose, 3 phase/PVC/polycarbonate (bearing ISI marked), isolated body including providing PVC square/round block complete all as specified and directed.

S & F Stepped type(five steps) electronic fan regulator flush type complete all as specified and directed. (Make: Anchor, Model No. 14502 or equivalent make as per list of manufacturer)

S & F Factory made distribution board (DB), Double Door in sheet steel enclosure fitted with common bus bar neutral link, earth bar and din rail, SPN, 8 way, 240 Volts IP-43, IK -09, suitable for housing MCB's complete all as specified and directed.

S & F Factory made distribution board (DB), Double Door in sheet steel enclosure fitted with common bus bar neutral link, earth bar and din rail, SPN, 4 way, 240 Volts IP-43, IK -09, suitable for housing MCB's complete all as specified and directed.

S & F MCB, SPN, 240 Volts, 6 to 32 Amps, 'C' Series, 10KA breaking capacity complete all as specified and directed.

S & F MCB, 'C' Series, SP, 240 Volts, 6 to 32 Amps, 'C' Series, 10KA breaking capacity complete all as specified and directed.

M & L for Sub main wiring with two runs of 4 sqmm (Nominal area) single core FRLS cable PVC insulated, multistranded, unsheathed, copper conductor cables 1100 Volts grade drawn through PVC conduits, medium grade, of suitable size, fixed to wall/ceiling etc with all accessories, fittings, fixures including 4 sqmm (nominal area) single core, PVC insulated, multistranded, unsheathed, FRLS copper conductor as earth wire and duly connected to common earth point including PVC conduits/casing-caping of suitable size complete all as specified and as directed by Engineer-in-charge. (Note : PVC Conduits, two run wiring cables and one run of earth wire will be measured as one length.)

S&F LED tube light fitting of 18 watts 6000K , 230 volt, basic all purpose surface and wall mounted type with polycarbonate housing & integrated electronic driver complete with all fixing accessories such as 2 nos of PVC square/round boxes, screws, etc and providing & connecting up with twin core flexible copper conductor cable of size 24/0.20 sqmm complete all as specified and directed by Engr-in-charge. Make : Havells Cat No LUMILINEBS18WLED830SPCWH or equivelent of Philips/Crompton Greaves/Bajaj

S&F LED tube light fitting of 9 watts 6000K , 230 volt, basic all purpose surface and wall mounted type with polycarbonate housing & integrated electronic driver complete with all fixing accessories such as 2 nos of PVC square/round boxes, screws, etc and providing & connecting up with twin core flexible copper conductor cable of size 24/0.20 sqmm complete all as specified and directed by Engr-in-charge. Make : Havells Cat No LUMILINEBS09WLED830SPCWH or equivelent of Philips/Crompton Greaves/Bajaj

S&F new generation energy saving environmental friendly long life, with high power LED building street light/security light 1x 15 Watt LED pressure die-cast aluminium, heat resistant, toughened glass diffuser, IP65/66 protection and impact resistant of IK7 prewired with all accessories and connection up with 3 core flexible copper conductor cable 4/20 mm size, 1.5m long and testing on installation all as specified and directed. Make Havells Cat No ENDURAPEARLSL15WLED757SASYTOPC or equivelent of Bajaj/phillips/CG

S&F in replacement security light bracket made out of 25 mm bore GI Light grade 1.00 M long to required shape as in bracket for steet light fittings fixed with two pair of MS flate iron clamp of size 50mm X 6 mm thickness of required shape with nuts, bolts and washers suitable for steel tubular pole including painting of mild steel flate iron surface with two coates of synthetic enamel paint over a coat of red oxide primer complete including taking down unserviceable one all as specified and directed.

M & L for hook/clamp for hanging of ceiling fanfabricated out of 40X6mm Mild steel flat iron made to shape as required, fixed on angle iron truss/GI tubing member using necessary bolts, nuts, rubber bushing and washers including two coats of painting over a coat of primer complete

Taking down ceiling fan/exhaust fan and applying one coat of painting at site using synthetic enamel paint using spray painting machine after cleaning properly including provision of suitable size twin core copper cable connecting up with ceiling rose, replacing 2.5/3.15 MFD capacitor, canopy, bearing, bush, rubber bushing, screws, bolts, nuts etc and greasing complete all as directed.

M & L for rewinding of ceiling fan using appropriate size of copper enamrlled wire including varnishing heating with proper insulation including testing complete all as directed.

Supply installation commissioning and testing of deep freezer glass top of capacity 400 litres, electric driven, single phase, 230 Volts, complete all as directed. Make Bluestar GT- 400/Whirlpool/Voltas as approved by GE

Supply installation commissioning and testing of refrigerator, electric driven (single phase), 230 Volts of capacity 360 Litres, BEE 5 Star rated complete all as directed. Make LG/Whirlpool/Voltas as approved by GE

Supply and fix Voltage stabilizer of 3 KVA for automatic operation single phase naturally cooled indoor type & designed for input variation between 170 V to 250 V with output voltage stabilized at 230V with accuracy of 2.5% Plus/Minus . Make AE /Venus/Sen & Pandit/Vertex.

M & L Earthing complete with Galvanised steel earth plate electrode 600 mm x 600mm x 6 mm thick burried directly in ground vertically to a depth not less than 2.25 m below ground level with the top edge of earth plate at depth not less than 1.5 m below ground level connected to galvanised earth lead wire 4.0 mm dia by means of bolts, nuts, check nuts and washers protected by 15mm bore light grade GI pipe, funnel with 20mm bore GI medium grade pipe for watering, wire mesh, including concrete pit in PCC (1:3:6) type C-1, pre-cast RCC 1:2:4 type B-1 cover slab of size 350x350x50mm reinforced with 8mm dia TMT steel bars @15cm centre to centre in both direction and 10mm dia MS handle of suitable size, charcoal or coke and salt in alternative layers,necessary earth work in soft/loose soil all as shown in Electrical Plate No 3 of MES Schedule Part I and testing complete inclduing taking down old one as specified and as directed.

docileworx