Workers Shed facilities and Misc. Civil works for NREP

Amount

EARTH WORK :

Mode of measurement for Excavation: For excavation in soil/ hard murrum only PCC area is to be measured with depth of excavation as per drg. Additional excavation for working space, slope cutting shall be included in rate and no extra measurements shall be paid. Proper storage / stacking of construction material and handling of excavated material is contractor's responsibility. He has to organize the same such that re-handling is avoided. Contractor shall use his judgment while stacking / carting away excess earth. Provision of adequate barriers, lighting, gangways across open trenches etc for protection of workman and public in scope of Contractor at his own cost.

Ploughing the existing ground up to a depth of 25 cm and removal of rubbish/vegetation upto a distance of 3.0 KM from plot boundary, levelling, watering the ground and rolling with 8-10 ton power roller as required.

Earth work in excavation for all kind of Soil including all labour, materials, dressing of sides, pumping & bailing out water accumulated due to rain and / or subsoil waters and including disposal or stacking, leveling and neatly dressing as decided by Engineer-in-Charge including providing temporary supports to existing service lines like water pipes, sewerage, electric cables, etc., if any, complete, including shoring/ strutting /sheet pile, all materials and labour complete and as directed by Engineer-in-Charge for following depth. Excavated soil shall be disposed at least 50 m away from the Plant Boundary / kept for backfilling within a radius of 500M and the charges for the same is included in this item.

-do- but from grade level upto 1.5m depth

-do- but from 1.5m to 2.5m depth from grade level

Transportation of surplus earth/debris to dumping area outside site Carting the surplus excavated earth/rocks and debris from construction area beyond the initial lead of 500 meters to the approved dumping area outside the plant boundary at any distance from the site, including re-excavating the deposited soil excavated earlier, transportation, loading, unloading, laying at all depths/heights, stacking, levelling and dressing both the area (viz. from where the earth is carted and where it is deposited) to required levels and slopes complete with all lifts. Any payment of fee and duties for using the dump.

Providing and laying 90 to 63 mm crushed/broken stones in two layers 115mm each for total thickness of 230 mm including filling interstices with sand/ hand crushed metals, well packed in line and level, rolling with Power / hand Roller, etc. compete.

Providing and laying upto 225mm thick consolidated Wet Mix Macadam base course in Three layer of each of 75mm thick consolidated with graded stone aggregate of size 75 micron - 53 mm (refer table 400 -11) of approved quality and prepared in approved mixing plant with water to required OMC, carriage of mixed material by tipper to site laying in uniform layer and compacting with power vibratory roller to achive the desired density etc. as per MORTH technical specification.

Suppy and Laying of Gravel / Rubble Soling with Max size of 20mm Gravels laid in Layers (Not Exceeding 150mm Thick for each layer) and compacted of 85% Relative Density as per IS:2720. Before proceeding, the base shall be compacted 95% maximum dry density.

CONCRETE WORKS

The rates shall be inclusive of dewatering, scaffolding, stagging, machine-mixing, hoisting manually or by means of mechanised equipment, placing, vibrating and tamping, Hacking, roughening of concrete surface for receiving plaster, curing, testing, etc. No finishing items to be considered in quoting the rates of RCC work unless otherwise specified. Required Necessary testing of Design mix / Ready mix, in approved third party lab and submission of report to owner is in scope of Sub-contractor at his own cost. Cement, aggregate and sand for preparation of Design mix is in scope of Sub-contractor at his own cost. Contractor to arrange RMC of approved design mix either through their own Batching plant / Supply from other Vendor outside Refinery Primes including Royalties for Forest materials, if any and nothing extra shall be payable in this regard.

Providing and laying in position Plain Cement Concrete 1:4:8 (1 Cement: 4 Coarse Sand: 8 Graded Stone Aggregates) with 40 mm and down size graded stone aggregate as leveling course in foundations, under slabs on grade etc., including tamping, curing, shuttering etc. complete for all depths and heights. For details refer specification for Plain and Reinforced concrete (NR-0ZZZZ-CV-SPE-0002). Materials to be supplied as per approved vendor lists attached with special conditions of contract.

Foundation Concrete: Providing and laying in situ Reinforced Cement Concrete of any Design Mix and specified grade using ordinary Portland cement and 20 mm and down size graded stone aggregates including providing pockets / shear keys, during concreting, vibrating, tamping curing addition of plasticizers and rendering if required to give a smooth and even surface etc. complete in all types of substructures for example in rafts, foundation beams, footings, retaining walls, columns, pedestals, sleepers, Drains, Trenches, Man-Holes, Catch-Basins and other similar UG items not specifically mentioned herein but used in Facilities below the Pavement, for all depths including the supplying and applying of admixtures, But Excluding corrosion inhibitors like bipolar concrete penetrating corrosion inhibiting materials (which is covered in item 4) as specified in the Drawings and as per specifications and directions of Engineer-in-charge. For details refer specification for Plain and Reinforced concrete (NR-0ZZZZ-CV-SPE-0002). Materials to be supplied as per approved vendor lists attached with special conditions of contract.

-do- same as Item 2, but For Grade M25

-do- same as Item 2, but For Grade M30

Elevation Concrete: Providing and laying in-situ Reinforced Cement Concrete of Design Mix and of specified grade using ordinary Portland cement and 20 mm and down size graded stone aggregates including provision of pockets/shear keys, fixing metal inserts / sleeves and anchor bolts in position during concreting, vibrating, tamping curing, addition plasticizers and rendering if required to give a smooth and even surface including painting of concrete surfaces etc. in all types of superstructures like Piperacks, Process Structures, Buildings etc. and for all types of Concrete Elements like columns, beams, floor & roof slabs, pedestals, elevated machinery supporting structures, staircases and their support brackets, fins, louvers, parapets and any other elevated concrete works not specifically covered herein, all complete as per drawings/specifications and as directed including the supply and applying of admixtures , But Excluding corrosion inhibitors like bipolar concrete penetrating corrosion inhibiting materials (which is covered in item 4) as per specifications and directions of Engineer-in-charge. For details refer specification for Plain and Reinforced concrete (NR-0ZZZZ-CV-SPE-0002). Materials to be supplied as per approved vendor lists attached with special conditions of contract.

-do- same as Item 3, but for Grade M30

Corrossion Inhibitors - Bipolar Concrete penetrating Corrosion inhibiting Materials

Supplying & placing in position High Yield Deformed Bar Reinforcement conforming to IS-1139 or Cold Twisted bar, TOR steel / TMT / or Equivalent (Reinforcement conforming to IS-1786. Fe-500 / Fe-500D) for all type of RCC structures including cleaning, decoiling, cutting, bending to required shape and lengths, binding as per drawing and details, binding with 16 SWG black soft annealed binding wire supplying and straightening, placing with proper cover block, support chairs, overlaps, spacers, etc.complete in all respect as directed. Payment will be made as on length basis (actual or theoretical as per drg. whichever is less) and converted into weight by using standard IS coefficient (rolling margins, wastages, couplings, welded joints, spacer bars, stays, hangers, annnealed steel wire or other methods of binding and placing shall not be measured and not paid separately. Only authorised laps and chairs shall be measured and paid)

Providing and erecting in position form work, shuttering and boxing using plywood / steel shuttering materials of approved quality for all height and all type of concrete elements vertical, horizontal or inclined including scaffolding, stagging, fasteners, nails, wires, keeping in position till concrete is laid and members have acquired required strength, removal thereafter, applying shuttering oil etc. complete as directed by Engineer-in-Charge.

Providing surface treatment to foundations in contact with aggressive water or soil in form of linings, membranes, mastic seal, coal tar epoxy paint, bitumen paint / layer, mortar fillet, protection board etc including materials, tools and tackles as specified in the Drawings, specifications and directions of Engineer-in-charge. Inspections and Tests as per relevant specification / IS codes shall be deemed to be included in the scope

-do- but with two coats of hot bitumen paint of grade 20/30 with quantity of bitumen at least 1.2 kg/sqm per coat

Providing Anti-termite Treatment to Floors, bottom and sides of foundations, etc for buildings. Work shall be carried out by specialized agency for termite / pest control to their own specifications subject to the minimum specifications as specified in IS:6313, Part II using material as per IS 8944. The work shall carry a guarantee for satisfactory performance for a minimum period of 10 years.

MASONRY WORK :

Providing First class Brick Masonry work with a minimum crushing strength of 6 MPa in Cement Mortar 1:6 (1 Cement: 5 Sand) in foundation and plinth with approved brick having minimum crushing strength of 35 KG / Sqcm including providing recesses, opening, including scaffolding, racking out joints, curing etc., finishing the joints flush below ground level and raking out joints in plinth etc. including all tools, tackles, ladders for access to foundation pit, making working platform, etc all complete as per drawings, specifications and directions of Engineer- in-charge.

-do- but for Foundation and upto Plinth Level

'Providing First class Brick Masonry work with a minimum crushing strength of 6 MPa in Cement Mortar 1:6 (1 Cement: 5 Sand) in Superstructure for all heights, with approved brick having minimum crushing strength of 35 KG / Sqcm including providing recesses, opening, including scaffolding, racking out joints, curing etc., finishing the joints flush below ground level and raking out joints in plinth etc. including all tools, tackles, ladders for access to foundation pit, making working platform, etc all complete as per drawings, specifications and directions of Engineer- in-charge.

-do- but for Superstructure above plinth level (One or more Brick thick wall)

-do- Superstructure above plinth level (Half Brick thick wall)

Supply of all materials required for construction of block wall, installing the same over already installed Tie Beams and / or Foundations using cement mortar of nominal mix including plumbing, leveling, etc as required as per the drawings, specifications and / or as directed by Engineer-in-charge. Concrete required in Sub Structure and / or Super Structure is not in the scope of this Work Code.

Solid block wall 100mm thk

Solid block wall 200mm thk

Providing and constructing 115mm thick partition wall and parapet at all height in cement mortar 1:4 (1 part of cement and four part of sand) including scaffolding, racking out joints, reinforcement of 2 Nos. 8mm dia bar at every 4th layer and watering etc. complete as directed. (steel shall be payable separately as per relevant item)

Providing and applying smooth cement plaster (with or without waterproofing compound) of given thickness conforming to IS-2645 (CICO/ approved equivalent) at all heights and below plinth in CM 1:6 to walls, beams, column, drain, bends, moulds, grooves, pattas and drip course to all brick and RCC surfaces including raking joints, scaffolding, curing finishing smooth including cost of cement, cleaning, hacking concrete surfaces, scaffolding, providing drip moulds, POINTING if required, watering, curing etc. complete for all heights, providing grooves (for 20 mm thick plaster) in plaster 12 mm wide and 12 mm deep where two different material like Concrete and Brickwork are in line all complete as specified in Drawings and specifications and as directed by Engineer-in-charge... The plaster shall be rubbed with "Iron Plate" till the surface shows cement paste in line level complete as directed.

-do- but with 12mm thick Cement Plaster without water proofing Compound using 1:6 mix mortar

-do- but with 20mm thick Cement Plaster without water proofing Compound using 1:6 mix mortar

Providing and applying two or more coats Acrylic Premium Emulsion paint of "Asian or Berger" make, and of approved colour and shade one coat of primer, brooming down and cleaning the surfaces, finishing of holes and depressions including scaffolding and staging of all levels with all labour and material etc. complete at all levels.

Providing and applying two or more coats, of "APEX WEATHER PROOF EXTERIOR PAINT" (Asian paint make) of approved shade to give good and even shade over plaster, brick surfaces at all levels as per instructions of the engineers-in-charge including a coat of primer scaffolding, cleaning, washing the surface etc. complete at all levels.

Providing and applying 1.5mm thick white cement based putty to full area of plaster in two coats to fill all pores of mortar/ concrete wall & ceiling, making the surfaces good & even for painting including scaffolding / staging, necessary tools etc complete at all levels as per instructions of Engineer-In-Charge.

Providing and laying average 100mm thick "BURNT CLAY TILE" waterproofing treatment for all R.C.C. terraces, balconies etc. with a base layer of 65mm average thick brick bat coba 1:2 in cement mortar 1:1 proportion to specified slopes covered with 15mm thick burnt, pressed clay tiles fixed over 20mm thick CM 1:4 (mortar to be mixed in crude oil in required proportion) pointing the joints in CM 1:3 mix, well grouted, finished to proper slope towards rain water pipe, etc. including supply of all materials, tools and labor all complete, as specified in the Drawings, specifications and directions of Engineer-in-charge.

PAVIOR

Providing & laying PCC "Tre mix system (vacuum dewatering system)" floor using M20 grade concrete in alternate panels. The panels shall be formed on four side with required MS channel bolted in position for forming the size . MS channel shall have provision of holes for dowel bars if required. The entire mass shall be vibrated with surface vibrator so as to bring out slurry on top and smooth finished integrally with ride-on- trowel, Curing by ponding etc. complete as per instruction of engineer in charge. Ponding shall be done with cement mortar vata with placing underneath 125 micron polythene sheet. The same shall be deemed to have included in quoted rate. Sand/Soil vata shall not be permitted. Note: 1.Rate of flooring shall be inclusive of all shuttering shall be required. 2.Vibrator shall be used "Flex screed SVE- Surface vibrator" of Aquarius Technologies pvt. Ltd. or equivalent make. For Finishing use Ride-on-trowel, Big Blue glider and Magnesium Bull float of Aquarius Technologies pvt. Ltd. or equivalent make. Rate of flooring shall be inclusive of above all.

150 mm thick RCC floor

Providing and applying "non metallic floor hardener using "Nito floor - hardtop" of Fosroc or "CHAPDUR" of sika make hardtop on RCC floor after base concrete has stiffened to the point when light foot traffic leaves an imprint of about 3mm and bleed water should have evaporated. It is applied at the rate of 5 Kg./Sqm of Area as per manufacturer's specification. Application of hardner shall be done by using topping spreader of Aquarius Technologies Pvt. Ltd or equilvanet make.

Providing & fixing a separation membrane of minimum thickness 125 micron polythene between the concrete floor and the sub-base plain cement concrete to reduce friction including cutting of plastic sheet as per site measurements, longitudinal and cross laps of minimum 150mm to 200mm. The said laps however, shall not be considered for payment, the same shall be deemed to have included in quoted rate.

Providing & fixing one side polished stone min. 1500 mm long for 300 mm wide Door / window Jams & sill with half round edge polish/moulding on one side and edge polish on other side including laying on 20mm thick C.M.(1:4) bedding (Stone may be cut into two pieces of required size and fixed in staggered manner including required overlapping with adhesive material as required, measurement shall be per running meter of total laid length only)

For 18 /20mm thick Marble stone.

For 18 /20mm thick black granite.

Providing and fixing 600 mm x 600 mm x 8 mm thick Ceramic tiles of approved make in flooring & skirting & dado including laying over 12mm thick C.M. 1:3 mix bed to proper level or slope and jointed with grey cement slurry @ 3.3 Kg/ Sqm including pointing in white cement mixed with matching colour pigment etc. complete. (Rate shall be inclusive of backing coat of cement plaster wherever required).

Same as above but Providing and laying glazed, ceramic matt-finished, non-slip decorative type tiles of specified size & approved make (SPARTEK or approved equivalent) including cleaning the finished surface with Oxalic acid, wax polishing (Manson/ Waxpol) as per Manufacturer’s specifications and / or as per the instructions of the Engineer-in-charge

Providing and fixing machine polished 20mm thick granite platform over 25 mm thick kota stone supports including providing opening for wash basin, kitchen Sink, pillarcock / bibcock etc including Half round moulding, filling joints, making connection for water inlet, etc. complete as directed.

Providing and fixing 18 mm thick granite partition. All the edges shall be cut on machine and polished on both side as well as on edge with rounded top including chasing the brick work & finish with cement mortar 1:3, including curing etc. complete.

Providing & fixing factory made Decorative coloured M-35 "Paver Block" of 80 mm thick of any pattern as approved, laid in line & level over and including ungraded sand bed of 100 mm thick including transporting, loading, unloading, stacking & fixing in position.

Providing & fixing Factory made Kerb stone using M20 concrete grade including excavation and back filling, transporting, sticking, placing kerb in position, Joint filling with C.M 1:6 etc. complete. In case of embedding kerb stones in PCC, the same shall be paid under relevant item.

size 300 x450 x150 mm thick

Providing and fixing False Ceiling Grid Framework for supporting ceiling tiles consisting of main and cross runners supported from roof slab at desired height in desired pattern including finishing, making the framework perfectly levelled and aligned, etc all complete as per Standard drawings, specifications and directions of Engineer-in-charge.

-do- but using 12.5 mm thick tapered edge gypsum plain board conforming to IS: 2095- Part I

DOOR/ WINDOW WORK :

Supplying, fabricating and fixing in position aluminum windows and ventilator using "JINDAL" make aluminum sections with approved colour anodizing (15 microns) including anodized aluminium beading, all tools and labor, fixing the frame to masonry/RCC by counter sunk galvanised machine screws and grouting to masonry with M-15 grade concrete in minimum 150mm x 150mm x 50mm sized hole/96mm long 12mm dia dash fastener, cup pivots of aluminium alloy as per requirements of the Architectural Aluminium Manufacturers Association (AAMA) and Supplying and fixing 5.5mm thick clear float toughened glass including sealing the gap between frame & plaster with sealant of approved make, all fixtures and fastening, fittings such as hinges, handles, tower bolts (concealed) etc. all as per drawing / manufacturing specification & direction of Engineer in charge.

-do- but for Two track Sliding Type window

-do- but for Louvered Type Window

Supplying, fabricating and fixing fully glazed anodized (25 micron)/electrostatic powder coated (50 micron, approved shade) aluminium doors with "JINDAL" make Aluminium sections and including all accessories like Steel / Aluminium Beading including door fixing frame with extruded tubular aluminium sections of thickness between 2.0mm to 3.2mm and 5.5 mm toughened glass fixed with rubber lining and anodized aluminium beading, including all tools and labor, fixing the frame to masonry/RCC with 16mm wide, 8.2mm thick 100mm x 70mm galvanised L-shaped slotted lugs screwed to the frame @ 600mm max. by counter sunk galvanised machine screws and grouting to masonry with M-15 grade concrete in minimum 150mm x 150mm x 50mm sized hole/96mm long 12mm dia dash fastener, cup pivots of aluminium alloy as per requirements of the Architectural Aluminium Manufacturers Association (AAMA), heavy duty hydraulically operated, adjustable floor mounted door closer (double action), 250mm and 150mm long, 10mm dia anodized aluminium tower bolt, one each for each shutter, brass body mortice lock (6 levers) with aluminium handle on both sides, and etc. all complete for each shutter, finishing and making good of any damaged work etc. all complete as directed by Engineer-in-charge.

-do- but for Fixed / Openable doors

Supplying and fixing in position Pressed steel door/ window/ ventilator frames of overall (assorted size) size of 125 mm x 60 mm (to be filled back side hollow portion with concrete), made of 16 SWG pressed steel sheet bent to shape as per drawing, using bending machine to form solid, true edges/ corners, stiffened with 50mm x 50 mm thick MS flat spacers welded to the frame facing the wall / column max @ 600 mm c/c including fixing the frame with masonry/ RCC/ metal frame work for partition etc. by means of 300 mm x25 mm x6 m M.S. holdfasts welded to spacers and grouted with M-15 grade concrete in min 350 mm x 100 mm x 100 mm sized hole in masonry/ 96 mm long 12 mm dia dash fasteners, bolting with metal frame work, making provisions for hinges, locking devices, other hardware by machine cutting and providing 3 mm thick M.S. pad plates at all areas of hardware fixations, welding etc. painting of all metallic surfaces by 2 coats of synthetic enamel paint (approved shade, ICI or approved quality red oxide zinc chromate primer/ electrostatic powder coating of approved shade (25 micron), finishing etc all complete and as directed.

-do- but for Single shutter with 6 lever, heavy duty mortice lock, pressure die cast zinc alloy handles on both faces, two nos. of 10mm dia. 250mm long M.S. tower bolt, one no. 16mm dia, 250mm long M.S. aldrop.

-do- but for Double shutter with 12mm dia, 300mm long pressure dia cast zinc alloy handles on both sides, 10mm dia, 250mm long M.S. tower bolt for each shutter, 16mm dia, 250mm long M.S. aldrop, Door Stopper etc.

Supplying and fixing in position 18 SWG mild steel push and pull type rolling shutters, conforming to IS: 6248 including tools, labor, all accessories like shutter (constructed with inter locking lath sections formed out of cold rolled steel strips 0.9mm thick, 80mm wide and 1.25mm thick, 80mm wide respectively for shutter width upto 3.5M and above 3.5M), jointless M.S. channel section for guide (min. 3.15mm thick), M.S. girders, pressed bottom rails, shutter suspension stud shaft with pully and cage with cowl, top rolling springs, locking arrangement and all fittings and accessories as per approved manufacturers drawings, painting with two coats of synthetic enamel of approved make & shade over a coat of approved quality red oxide zinc chromate primer, making good of all damaged surfaces etc. all complete and as directed.

-do- but for mechanically operated Rolling shutter by reduction gear type mechanism

Providing and fixing Factory made, overall 40mm thick block board flush shutter consisting of solid core block board bonded with phenol formaldehyde synthetic resin and faced on both faces with commercial type plywood/ teakwood veneering/ lamination bonded with phenol formaldehyde synthetic resin, including tools, labour, fixing `T' type second class teakwood perimeter beading fixed by means of approved quality neoprene based adhesive and nailing @ 300 mm max, painting exposed surface with two coats of approved shade and make synthetic enamel paint over approved quality primer coat, fixing 125mm long M.S. butt hinges [for each shutter, and with vertical spacing not exceeding 600mm) with door frame, finishing etc all complete and as directed. The scope shall include Supply and Installation of all Accessories like Vision Panels, Overhead/ Floor Mounted Hydraulic Door Closer, Mortise Door Locks, Handles on Doors, Tower Bolts, Kick Plates, latches, door stopper etc such that the Doors are handed over in a completed position. The scope shall include the Supply and Installation of Pressed Steel Frames required to install the Doors as per manufacturer’s recommendations, & specifications and directions of Engineer-in-charge

-do- but for door shutter faced with 1 mm lamination on both sides.

Providing and fixing wooden frames for doors and windows of size 100 X 60 mm or 120 X 60mm, including fixing the frame with masonry/ RCC/ metal frame work for partition etc. M.S. holdfasts grouted with M-15 grade concrete in min 350 mm x 100 mm x 100 mm sized hole in masonry all complete as per instructions of Engineer-in-charge.

-do- but with second class Indian Teak Wood

MISCELLANEOUS :

Providing & fixing PVC pipe of 4 kg / sq cm pressure of Supreme or Finolex make for rain water including all accessories and fixing materials, tools, tackles & labors etc. complete as directed.

-do- but for 110mm dia

-do- but for 160mm dia

-do- but for 200mm dia

Providing Grouting for pocket, foundation / anchor bolts, sleeves, anchors of any shape, size, for any member, including roughening, cleaning & curing, etc. complete as directed.

With readymix anti-shrink grout as per manufacturer's specifications having strength 450kg/cm2

Providing and fixing anchor fasteners of approved make including drilling hole in RCC, finishing the surface etc complete as per the instructions of Engineer-in-Charge.

20mm dia x 100mm long

20mm dia x 150mm long

16mm dia x 100mm long

16mm dia x 150mm long

12mm dia x 150mm long

12mm dia x 100mm long

Providing, drilling & fixing anchor bars in concrete using Hilti HY-150 chemical grout as per as per manufacturer's specifications. (Reinforcement for rebaring will be in Sub-contractor's scope)

8 mm dia.

10 mm dia.

12 mm dia.

16 mm dia.

20 mm dia.

25 mm dia.

Providing & laying RCC NP2 class conforming to IS: 458 for pipes with Spigot jointed drains, cables crossing etc. including excavation upto required depth & width & disposal of surplus earth within plot boundary limits lowering to required level/ gradient, jointing with CM 1:2, laying of pipe in joints, back filling the trenches, compaction and making good teh same etc. complete (Encasing P.C.C. work and bed concrete for laying will be paid separately as per regular item). Inspection & hydraulic testing of the pipes will be witnessed by the representative of client/Consultant at Manufacturer's shop before dispatch.

300mm dia. Pipe

450mm dia. Pipe

600mm dia. Pipe

Supplying and laying in position PVC pipes confirming to IS:4985 embedded in Concrete with Surface Reinforcement for cable crossings. Scope shall include cutting the pipe if necessary, lowering, laying in position to proper levels, slopes etc. providing proper jointing as per code requirements or manufacturers recommendations, etc all complete as per drawings, specifications, and directions of Engineer-in-charge. For Single or groups of PVC Pipes as indicated in drawings.

-do- but 150mm dia PVC Conduit (6")

Supplying, Laying, Jointing of HDPE pipes (High Density Polyethylene Pipes) confirming to IS 4984/14151/12786/13488 with necessary jointing material like mechanical connector of jointing pipes by heating to the ends of pipes. HDPE Pipes of renowned manufacturer duly tested, and inspected i/c transportation charges, transit insurance, loading/ unloading and stacking at site/ store etc, complete.

-do- but HDPE Pipe Sleeve size 150mm (6" )

STRUCTURAL STEEL WORK

Supplying, fabricating and erecting in position steel structures conforming to IS : 2062 grade BR comprising of rolled and built up sections for side runners, beams, columns, trussed girders, sag rods, etc., including the cost of straightening if required, cutting to required size bolting and or welding of joints as per drawings, Surface preparation SSPC-SP-10, painting with one coat of 60 micron DFT of inorganic zinc silicate primer, 1 coat of 100 micron Two pack Epoxy HB Poly amide cured, fixing in line or level with temporary staging, complete with all tools, equipments and labour for all depths and heights as per drawings and directed by the Engineer-in-charge. Materials to be supplied as per approved vendor lists attached with special conditions of contract.

-do- but for Structural Steel Inserts, Edge Angles with TMT Fe500D lugs & exposed surface painted

Supplying, Fabricating and Installation/Erection of Steel work in built up tubular sections of YSt310 Grade Conforming to IS 1161 (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying of 1 coat priming coat and 2 coats of synthetic enemel paint of approved make of approved steel primer, including welding and bolted with special shaped washers etc. complete at all heights.

Supplying, fabricating and fixing in position anchor bolts, foundation bolts (bolt assembly supplied by contractor ) in line & level as per drawing complete including application of grease and covering with plastic cover. (Necessary templetes, handling & positioning is in scope of civil Sub-contractor for fixing bolts & quoted rates includes the same)

Supplying & fixing of Precoated GALVALUME roofing sheet of TCT specified thick for roofing work of approved manufacturer complete in all respects with self drilling & tapping screws of "Buildex" or "Hilti" or "Corroshield" make EPDM washers etc. including cutting to proper size,mitering,laps, necessary scaffolding etc. Finish on the weather face of roof panels & related components shall be minimum 150 gms/sqm. Aluminum/Zinc alloy coating mass total of both sides (55% Alumimum + 43.5% Zinc + 1.5% Silicon coating class AZ150 or equivalent). Pre-treatment Chromate coating on either sides, Primer Coating (Epoxy) On Top side 5 to 7 Microns, PVDF material of 20-25 microns on Top side & Back Coat - Epoxy based 5 to 7 Microns.

-do- but for GALVALUME Sheet 0.5mm Thk.

-do- but for GALVALUME Sheet 0.8mm Thk.

Supplying of Precoated GALVALUME Cladding sheet of TCT 0.8 mm thick for side cladding of approved manufacturer complete in all respects with self drilling & tapping screws of "Buildex" or "Hilti" or "Corroshield" make, EPDM washers etc. including cutting to proper size, mitering, laps, necessary scaffolding etc. Finish on the weather face of wall panels, and related components shall be Minimum 150 gms/sqm Aluminum / Zinc alloy coating mass – total of both sides (55% Aluminum + 43.5% Zinc + 1.5% Silicon- Coating class AZ150 or equivalent), Pre-treatment Chromate coating on either sides, Primer Coating (Epoxy) On Top Side 5 to 7 Microns, PVDF material of 20-25 microns on Top side and Back Coat – Epoxy based 5 to 7 Microns.

Supplying, fabricating & fixing in position Galvalume gutter made from 0.6 mm thick Galvalume sheet including cutting, bending & welding in pieces of requirement, joining with splice at bottom 100mm wide, welding on top as well as bottom for water proof joint, fixing the gutter to proper slope to the spout, making necessary drop ends/boxes with outlet for downtake pipes of required size and length, painting outer surfaces of gutter with two coats of synthetic enamel paint over a coat of primer, testing the gutter etc. complete to the satisfaction of Engineer-In-Charge. Necessary steel structure for supporting gutters shall be paid under item no.1 above. (Measurement shall be for developed area of gutter only & boxes/drop ends shall not be measured separately). PVDF material of 20-25 microns on Top side and Back Coat – Epoxy based 5 to 7 Microns.

Supplying, fabricating & fixing in position of galvalume downspout (Min. Thickness = 0.6 mm) shall be done. Downspout and all connections shall be designed for a water discharge capacity of design rain fall intensity equal to 200 mm/hour. Downspout shall be connected with gutter with end box. Cross sectional area of end box shall be at least 2.5 times the down spout area and minimum 300 mm depth. Size of downspout shall be as per design or as per size given in tender drawing whichever is higher. Rate shall be paid for running meter length of downspout. PVDF material of 20-25 microns on Top side and Back Coat – Epoxy based 5 to 7 Microns.

Supplying, fabricating and delivering to site steel flooring (Chequered Plates / Gratings) for all types of platforms and as per standard drawings and/or specifications, including cost of steel, incorporating cut-outs where shown in drawings, providing drainage holes, painting / galvanising as specified, repairs of damaged surface coat after erection, complete with all tools, equipments and labour, for all depths and heights as per drawings and as directed by Engineer-in-Charge.

-do- but for MS Chequered Plate 6mm THK (in plain) Grade E250A IS:2062. Weight of Chequered Plates will be considered as 53.2kg/sqm.

Providing and fixing, stainless steel (Grade 304) railing with all bends, elbows , etc., including welding, grinding, Buffing, polishing and making curvature (wherever required) and Fitting the same with necessary stainless steel nuts and bolts all Complete including making drills in structures, fixing the railing with necessary accessories & stainless Steel dash fasteners, stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab complete as per drawing /standards complete in all respect to the satisfaction of Engineer-in-charge.

-do- but for Rectangular handrails

SANITARY WORK :

Providing and fixing White Orissa type W.C. pan of "CERA" make (no. 2071) of size 580 x 440 mm with `P' or 'S' trap (No. 9002). The rate shall include concealed flush cock with necessary inlet connection upto flush cock and outlet connections in concealed manner, cutting and making good floor etc. complete.

Providing and fixing approved make as per owner’s vendor list, flat back half stall type Urinals of 610mm x 400mm x 380mm size confirming to IS: 2556 Part-VI included all fittings of plumbing works related to inlet and out let connection breaking walls, floors and making good of same, painting all exposed metallic surfaces with 2 coats of approved shade and quality synthetic enamel paint over a priming coat of approved quality red oxide Zinc Chromate, making inlet and outlet connections, fixing with C.P. brass screws, finishing etc. all complete

Providing and fixing trough type stainless steel wash basin wash basin of size Length as per required sizeX 450 widex 160 deep of approved make, made of 304grade SS, with material thickness of 0.8mm, with surface satin finish, seamless welded construction, 50mm perforated outlet at the center, includind 40mm high rear upstand, side panels with integrated brackets including stainless steel screws and dowels. The rate shall include standard quality including inlet and outlet connections, Pillar cock long neck foam flow of make no. F100002, stop cock, angle cock of approved quality, C.P. Brass bottle trap, CI Brackets CP brass waste coupling, cutting & making good the wall, etc. complete. (All plumbing fixtures shall be of "Hindware/Jaquar" make). All necessary supports/brackets and fittings shall be S.S.Rate shall be for RM length of Basin.

Providing and fixing stainless steel sink with drain board of Nirali or equivalent make of overall size 510 x 1040 x178 depth of approved make in line and level including providing & fixing 32mm diameter C.P. Bottle trap, waste coupling of approved make inlet and outlet connections etc. complete as per instructions of Engineer-in-charge.

Providing and fixing Hindware Italian collection Venezia 91011 on-counter wash basin including Jaguar Florentine 5005B single lever mixer, Jaguar Allied 709 32 mm waste coupling, Jaguar Allied 769 32 mm CP Bottle Trap, Jaguar Continental 053 KN CP Angle Cock, Jaguar Allied 803B 450 mm long bradied hose etc of the same or approved equivalent make all complete as per drawings, manufacturer’s specifications and as directed by Engineer-in-charge

Providing and fixing in position best quality approved make 6mm beveled edge mirror fixed to the backing with 4 nos of CP cap screws & washers including fixing the mirror to the wall with necessary screws, plugs & washers etc. complete.

Providing and fixing C.P. brass bib cock of "Jaquar" make (No. FLR-5047N) of 15mm dia including Teflon tap, leak proof fittings, etc.

Providing & fixing Stainless steel liquid soap holder cum dispenser of approved make to the wall with necessary brackets, screws, washers, plugs etc. all as specified & directed.

Providing and fixing 15mm C.P. Brass stop cock "Jaquar" make (No. FUS-29053) (open or concealed) of standard design approved make.

Providing ,fixing & testing pipes for water supply of following diameters at all levels, including with all necessary fixtures like bends , elbow etc. Quoted rate shall be inclusive of excavation and refilling the trenches / cutting floors & wall / making hole in RCC/ Brick work / making groove/ clamping finishing, jointing & sealing the same with sealant , making good after work etc. including hydro test complete as directed by engineer in charge.

Do as above item no. 8.10 for U-PVC (Type-B) Plumbing pipe as per ASTM - D - 1785 of "Supreme or Finolex" make & of nominal diameter of pipe.

15mm dia. pipe

20mm dia pipe.

25mm dia pipe.

32mm dia pipe.

40mm dia pipe.

50mm dia pipe.

Do as above item no. 8.10 for GI class -C

15mm dia. pipe

20mm dia pipe.

25mm dia pipe.

32mm dia pipe.

40mm dia pipe.

50mm dia pipe.

Supplying, fixing & testing PVC pipe (6 Kg/Sq cm) of supreme / Finolex make or equivalent make for sewage line including cutting, testing and providing all necessary fitting & fixtures, laying into required slope, joining the pipe with approved make cement or sealant, making the surface good etc. all complete.

160mm dia.

110mm dia.

75mm dia

Providing and fixing 100 mm dia. C.I Vent pipe upto 1m length with Cowl piece for Air Ventilator with jali wire mesh including 25mm deep seal lead joint. etc. complete.

Providing & fixing round / reactangle C.I Light / Medium duty manhole cover with frame in position on RCC/brick masonry including two coats of bituminous paint etc complete.

Providing & fixing brass stop valve with ISI marked approved make & quality. All completed.

25mm dia pipe.

40mm dia pipe.

50mm dia pipe.

Providing and fixing in position screw down brass wheel valve including necessary socket, union, nut etc. complete (conforming to IS 878).

25mm dia pipe.

40mm dia pipe.

50mm dia pipe.

Providing and placing on terrace polyethylene water storage tank of ISI: 12701 marked indicating the BIS license No. with cover and suitable locking arrangement and making necessary holes for inlet, outlet and over flow pipes, supply and fixing of fittings but without the base support for tank (Sintex, Electroplast, Star, Lotus or equivalent having valid ISI License)

1000 Litre

Providing and constructing chambers / Manholes of 600 x 600 mm clear size including excavation, backfilling, removal, formwork, reinforcement laying, M-7.5 bed concrete 150mm thick, 230/350mm thick brick masonry in cement mortar 1:6,12 mm Plaster in C.M (1:3) with floating coat of neat cement on inside, outside & top surface, RCC M15 grade for coping and 100 mm th. slab to receive precast cover/grating/ C.I cover, making necessary channel into floor with PCC 1:2:4 finished with floating coat of neat cement, (exluding pre cast cover, grating, angle frame, steel reinforcement ) etc. complete.

Note: clear depth is depth from bottom of cover to top of floor channel

Upto 1.0 mtr. Clear depth

Providing and constructing chambers / Manholes of 750 x 750 mm clear size including excavation, backfilling, removal, formwork, reinforcement laying, M-7.5 bed concrete 150mm thick, 230/ 350/450mm thick brick masonry in cement mortar 1:6,12 mm Plaster in C.M (1:3) with floating coat of neat cement on inside, outside & top surface, RCC M20 grade for coping and 100 mm th. slab to receive precast cover/grating/ C.I cover, making necessary channel into floor with PCC 1:2:4 finished with floating coat of neat cement, Foot rest of hot dip galvanized 20mm dia bar @ 300mm c/c. (exluding pre cast cover, grating, angle frame, steel reinforcement ) etc. complete.

Upto 1.0 mtr. Clear depth

Providing and Installing Septic Tank of Type-V incliuding the supply of all materials required to complete the installation of the tank to make it ready for the intended use including the supply and installing the concrete foundation, lean concrete below the foundation, Brickwork, Vent Pipes (with all accessories such as bend, jucction cowls etc), Manhole cover(as per IS 1726 Garde MD 10), inside plaster as required, providing buffle walls, providing water proof compound, etc all complete as per standard prcticees, Specification, Drawings and as per direction of Engineer-in-Charge

Providing and Installing of Soak Pit of Type-V including the supply of all materials required to complete the supply and laying of Bricks Bats inside the soak pit, to make it ready for the intended use including the supply and installing the straw Filling, Earth Filling, inlets etc all complete as per the Standard Practices, Specifications, Drawings and as per the direction of Engineer-in-Charge.

Dewatering from CRWS collection Pit near MS Block Area

Dewatering through deploying 01 No. 5 HP Dewatering Pump in drain keeping 50 Metre Flexible Hose Pipe including all resources, manpower, power source etc.

Dewatering through deploying 01 No. 10 HP Dewatering Pump in drain keeping 50 Metre Flexible Hose Pipe including all resources, manpower, power source etc.

Description of Work / Item(s)

Amount

SUPPLY, INSTALLATION, TESTING, COMMISSIONING OF VENTILATION SYSTEM FOR HT-002 SWGR (Near SS - ETP)

Supply, transportation up to erection and installation in site, earthing, testing, operational and functional checking and commissioning of the Ventilation system along with necessary wiring and panels. Complete with labour & materials, as per approved drawings, specifications of this tender and directions of Engineer-in-charge.

Ventilation system shall consist of the following: i) Weather Protection Louvers along-with bird protection screen on air intake ii) Fan with electrical motor ( min. flow rate 4000 m3/hr, static pressure 50 mm WC) iii) Automatic gravity damper at fan outlet for isolation iv) Particle filters with filtration efficiencies Pre-filter G4 (as per EN 779)/(ASHRAE MERV 8) & Fine Filter F7(as per EN 779)/(ASHRAE MERV 13) v) Galvanized Steel Sheet(GSS) duct work with zinc coating conforming to IS 277 Gr.200 as required along with grilles/ diffusers vi) Adequate supports for all the HVAC equipments

A Pressure Relief Damper (PRD) (700 mm * 700 mm) to relieve overpressure (with cowl and bird screen)

415V, 3 ph, Motor DOL Starter panel, 2.5mm CRCA Sheet steel enclosure material, IP55, Suitable for structure / wall mounting, complete with following for above Ventilation fan motor: Incoming side : MCCB, Ammeter, Voltmeter Indication Lamp : R/Y/B Indication lamp for Incoming supply healthy and "ON", "OFF", "TRIP" Lamp for Motor status Contactor, EOCR for motor protection Start & Stop PB’s : Start Push button (Shrouded type) Green in color and Stop Push button shall be mushroom headed, press to lock & turn to release type, Red in color. Provision for start/ stop from Control Room (DCS) shall be provided.

Associated incoming and outing power and Control cables, cable termination gland & lugs and earthing for HVAC EQUIPMENT

SUPPLY, INSTALLATION, TESTING, COMMISSIONING OF VENTILATION SYSTEM FOR HT-003 SWGR (Near SS - 05)

Supply, transportation up to erection and installation in site, earthing, testing, operational and functional checking and commissioning of the Ventilation system along with necessary wiring and panels. Complete with labour & materials, as per approved drawings, specifications of this tender and directions of Engineer-in-charge.

Ventilation system shall consist of the following: i) Weather Protection Louvers along-with bird protection screen on air intake ii) Gas Damper iii) Fan with electrical motor ( min. flow rate 4000 m3/hr, static pressure 50 mm WC) iv)Particle filters with filtration efficiencies Pre-filter G4 (as per EN 779)/(ASHRAE MERV 8) & Fine Filter F7(as per EN 779)/(ASHRAE MERV 13) v) Galvanized Steel Sheet(GSS) duct work with zinc coating conforming to IS 277 Gr.200 as required along with grilles/ diffusers vi) Adequate supports for the HVAC equipments

A Pressure Relief Damper (PRD) (700 mm * 700 mm) to relieve overpressure (with cowl and bird screen)

Power Panel for Fan and Dampers: 415V, 3 ph, Motor DOL Starter panel, 2.5mm CRCA Sheet steel enclosure material, IP55, Suitable for structure / wall mounting, complete with following for above Ventilation fan motor: Incoming side : MCCB, Ammeter, Voltmeter Indication Lamp : R/Y/B Indication lamp for Incoming supply healthy and "ON", "OFF", "TRIP" Lamp for Motor status Contactor, EOCR for motor protection Start & Stop PB’s : Start Push button (Shrouded type) Green in color and Stop Push button shall be mushroom headed, press to lock & turn to release type, Red in color. Provision for start/ stop from Control Room (DCS) shall be provided.

Control Panel with 2.5mm CRCA Sheet steel enclosure material, IP55, Suitable for structure / wall mounting, complete with necessary items and associated accessories.

Associated incoming and outing power and Control cables, cable termination gland & lugs and earthing for HVAC EQUIPMENT

SUPPLY, INSTALLATION, TESTING, COMMISSIONING OF SPLIT ACs FOR FIRST AID ROOM

Supply, transportation up to erection and installation in site, earthing, testing, operational and functional checking and commissioning of the Split ACs along with necessary wiring. Complete with labour & materials, as per approved drawings and directions of Engineer-in-charge.

3 Ton Split AC (3 star rating or above) (Inverter type)

1.5 Ton Split AC (3 star rating or above) (Inverter type)

Description of Work / Item(s)

Amount

SUPPLY, INSTALLATION, TESTING AND COMMISSIONING OF AUXILIARY POWER DISTRIBUTION BOARD

Supply, installation, testing and commissioning of 415V AC, 63A Indoor Auxiliary Power Distribution Board for First Aid Center. 415V, 63A, TPN, 10KA for 1 Sec, 2.5 mm thick CRCA sheet steel enclosure material with inside partition, enclosure protection IP54, suitable for indoor installation and wall / structure mounting, Bottom Cable entry for both incoming feeder and Top Cable entry for outgoing feeders, complete with SS material name plate, nut, bolt for mounting and associated accessories. The incomer shall be suitable for termination of 3.5CX50 sq mm AL conductor, Armoured, XLPE insulated, FRLS Power cables. All outgoing feeders shall be suitable for termination of 3CX 6/4 sq mm, CU conductor, Armoured, XLPE insulated, FRLS Power cables. Incoming and outgoing feeders are as follows : Incomer feeder (One number) : 63A, 4P MCB, R,Y,B Indication Lamp Outgoing feeder (Six Number) : 32A, 4P, MCB

SUPPLY, INSTALLATION, TESTING AND COMMISSIONING OF LIGHTING PANELS

Supply, installation, testing and commissioning of Indoor Lighting Panel. 415V AC, 63A, TPN, 24 Way, 10KA for 1 Sec, 2.5mm thick CRCA sheet steel enclosure material, with inside partition, enclosure protection IP54, suitable for indoor installation and wall / structure mounting, Bottom Cable entry for incoming feeder and Top Cable entry for outgoing feeders, complete with SS material name plate, nut, bolt for mounting and associated accessories. One number Auto / Manual switch, Timer, Timer controlled contactor shall be provided for automatic ON/OFF operation for few outgoing MCB feeders for building peripheral lighting. The incomer shall be suitable for termination of 3.5CX50 sq mm AL conductor, Armoured, XLPE insulated, FRLS Power cables. All outgoing feeders shall be suitable for termination of 3CX4 sq mm OR 3CX2.5 sq mm, CU conductor, Armoured, XLPE insulated, FRLS Power cables. The incoming feeders and outgoing feeders are as below: Incomer feeder (One Number) : 63A, 415V, 4P MCB, R,Y,B Indication Lamp Outgoing feeder (Twenty four Number) : 16A, 240V DP MCB with 16A ELCB

Supply, installation, testing and commissioning of Indoor Lighting Panel. 415V AC, 63A, TPN, 18 Way, 10KA for 1 Sec, 2.5mm thick CRCA sheet steel enclosure material, with inside partition, enclosure protection IP54, suitable for indoor installation and wall / structure mounting, Bottom Cable entry for incoming feeder and Top Cable entry for outgoing feeders, complete with SS material name plate, nut, bolt for mounting and associated accessories. One number Auto / Manual switch, Timer, Timer controlled contactor shall be provided for automatic ON/OFF operation for few outgoing MCB feeders for building peripheral lighting. The incomer shall be suitable for termination of 3.5CX50 sq mm AL conductor, Armoured, XLPE insulated, FRLS Power cables. All outgoing feeders shall be suitable for termination of 3CX4 sq mm OR 3CX2.5 sq mm, CU conductor, Armoured, XLPE insulated, FRLS Power cables. The incoming feeders and outgoing feeders are as below: Incomer feeder (One Number) : 63A, 415V, 4P MCB, R,Y,B Indication Lamp Outgoing feeder (Eighteen Number) : 16A, 240V DP MCB with 16A ELCB

Supply, installation, testing and commissioning of Indoor Lighting Panel. 415V AC,63A, TPN, 12 Way, 10KA for 1 Sec, 2.5mm thick CRCA sheet steel enclosure material, with inside partition, enclosure protection IP54, suitable for indoor installation and wall / structure mounting, Bottom Cable entry for incoming feeder and Top Cable entry for outgoing feeders, complete with SS material name plate, nut, bolt for mounting and associated accessories. One number Auto / Manual switch, Timer, Timer controlled contactor shall be provided for automatic ON/OFF operation for few outgoing MCB feeders for building peripheral lighting. The incomer shall be suitable for termination of 3.5CX50 sq mm AL conductor, Armoured, XLPE insulated, FRLS Power cables. All outgoing feeders shall be suitable for termination of 3CX4 sq mm OR 3CX2.5 sq mm, CU conductor, Armoured, XLPE insulated, FRLS Power cables. The incoming feeders and outgoing feeders are as below: Incomer feeder (One number) : 63A, 415V, 4P MCB, R,Y,B Indication Lamp Outgoing feeder (Twelve Number) : 16A, 240V DP MCB with 16A ELCB

SUPPLY, LAYING / INSTALLATION, TESTING AND COMMISSIONING OF 1.1KV GRADE LOW VOLTAGE POWER CABLES

Supply & Laying of 1.1 kV Grade, Al conductor, XLPE insulated, Extruded PVC inner sheathed, armoured and FRLS PVC outer sheathed power cables as per the data sheet of cables:

Supply of 1.1 kV Grade, 3.5C X 50 sq mm, Al conductor, XLPE insulated, Extruded PVC inner sheathed, armoured, FRLS PVC outer sheathed LV Power Cable and Laying / Installation of 1.1 kV Grade, 3.5C X 50 sq mm Armoured, AL Cable in trays/Racks, supported on structures, clamping to column wall or structure using GI spacers and saddles (at an interval of 300 mm), Installation & supply of anodise Aluminium / Stainless steel tags for overhead & buried cables respectively. Installation & supply of G.I saddles & GI Clamps, clamping of cables on trays & necessary hardwares

Supply of 1.1 kV Grade, 3.5C X 95 sq mm, Al conductor, XLPE insulated, Extruded PVC inner sheathed, armoured, FRLS PVC outer sheathed LV Power Cable and Laying / Installation of 1.1 kV Grade, 3.5C X 95 sq mm Armoured, AL Cable in trays/Racks, supported on structures, clamping to column wall or structure using GI spacers and saddles (at an interval of 300 mm), Installation & supply of anodise Aluminium / Stainless steel tags for overhead & buried cables respectively. Installation & supply of G.I saddles & GI Clamps, clamping of cables on trays & necessary hardwares

Supply & Laying of 1.1 kV Grade, CU conductor, XLPE insulated, Extruded PVC inner sheathed, armoured and FRLS PVC outer sheathed power cables as per the data sheet of cables :

Supply of 1.1 kV Grade, 3C X 2.5 sq mm, CU conductor, XLPE insulated, Extruded PVC inner sheathed, armoured, FRLS PVC outer sheathed LV Power Cable and Laying / Installation of 1.1 kV Grade, 3C X 2.5 sq mm Armoured, CU Cable in trays, supported on structures, clamping to column wall or structure using GI spacers and saddles (at an interval of 300 mm), Installation & supply of anodise Aluminium / Stainless steel tags for overhead & buried cables respectively. Installation & supply of G.I saddles & GI Clamps, clamping of cables on trays & necessary hardwares

Supply of 1.1 kV Grade, 3C X 4 sq mm, CU conductor, XLPE insulated, Extruded PVC inner sheathed, armoured, FRLS PVC outer sheathed LV Power Cable and Laying / Installation of 1.1 kV Grade, 3C X 4 sq mm Armoured, CU Cable in trays, supported on structures, clamping to column wall or structure using GI spacers and saddles (at an interval of 300 mm), Installation & supply of anodise Aluminium / Stainless steel tags for overhead & buried cables respectively. Installation & supply of G.I saddles & GI Clamps, clamping of cables on trays & necessary hardwares

TERMINATION INCLUDING SUPPLY OF LUGS - 1.1KV GRADE LOW VOLTAGE POWER CABLES

Termination including supply of crimping type, heavy duty, long barrel type Alluminium lugs for 1.1 kV Grade, 3.5C X 50 sq mm, Al conductor, XLPE insulated, Extruded PVC inner sheathed, armoured, FRLS PVC outer sheathed LV Power Cable. Termination includes fixing of cable glands at panel or equipment.

Termination including supply of crimping type, heavy duty, long barrel type Alluminium lugs for 1.1 kV Grade, 3.5C X 95 sq mm, Al conductor, XLPE insulated, Extruded PVC inner sheathed, armoured, FRLS PVC outer sheathed LV Power Cable.Termination includes fixing of cable glands at panel or equipment.

Termination including supply of crimping type, heavy duty, long barrel type Copper lugs for 1.1 kV Grade, 3C X 2.5 sq mm, Al conductor, XLPE insulated, Extruded PVC inner sheathed, armoured, FRLS PVC outer sheathed LV Power Cable.Termination includes fixing of cable glands at panel or equipment.

Termination including supply of crimping type, heavy duty, long barrel type Copper lugs for 1.1 kV Grade, 3C X 4 sq mm, Al conductor, XLPE insulated, Extruded PVC inner sheathed, armoured, FRLS PVC outer sheathed LV Power Cable.Termination includes fixing of cable glands at panel or equipment.

SUPPLY OF WEATHER PROOF CABLE GLANDS

Supply of Weather Proof, Double compression Nickel plated brass Cable Gland for 1.1 kV Grade, 3.5C X 50 sq mm, Al conductor, XLPE insulated, Extruded PVC inner sheathed, armoured, FRLS PVC outer sheathed LV Power Cable

Supply of Weather Proof, Double compression Nickel plated brass Cable Gland for 1.1 kV Grade, 3.5C X 95 sq mm, Al conductor, XLPE insulated, Extruded PVC inner sheathed, armoured, FRLS PVC outer sheathed LV Power Cable

Supply of Weather Proof, Double compression Nickel plated brass Cable Gland for 1.1 kV Grade, 3C X 2.5 sq mm, CU conductor, XLPE insulated, Extruded PVC inner sheathed, armoured, FRLS PVC outer sheathed LV Power Cable

Supply of Weather Proof, Double compression Nickel plated brass Cable Gland for 1.1 kV Grade, 3C X 4 sq mm, CU conductor, XLPE insulated, Extruded PVC inner sheathed, armoured, FRLS PVC outer sheathed LV Power Cable

Supply of Weather Proof, Nickel plated brass Dummy Stopper Plug suitable for 1.1 kV Grade, 3C X 2.5 sq mm, OR 3C X 4 sq mm CU conductor, XLPE insulated, Extruded PVC inner sheathed, armoured, FRLS PVC outer sheathed LV Power Cable

SUPPLY, INSTALLATION, TESTING AND COMMISSIONING OF LIGHTING WORK

Supply, Installation (ceiling / wall mounting as per installation standard), earthing, glanding, termination of incoming and outgoing cables/ wires, testing and commissioning of 2x20W LED industrial luminaire (Tube light) CRCA precoated housing/polycarbonate housing duly prewired with accessories and trans-parent cover of polycarbonate complete with lamp & accessories. IP65 enclosure protection, suitable for installation in Indoor building lighting / worker shed lighting, building peripheral lighting. Scope of work includes Fabrication and installation of 19 mm dia GI pipe, Approx 1 meter length with mounting hardwares and accessories for mounting / fixing Light Fixtures from ceiling. Light fixtures shall be suitable for Loop-in Loop-out connections. The supply shall inclusive of cable gland for Incoming & outgoing cables. This shall include transportation from owner's issue point to actual place of installation by contractor's own lifting & transporting arrangement, unpacking, assembly of luminaries, drilling etc. as required, all labour and material complete as per drawings, specification of this tender and directions of Engineer-in-charge.

Supply, Installation (ceiling / wall mounting as per installation standard), earthing, glanding, termination of incoming and outgoing cables/ wires, testing and commissioning of Battery Backup Emergency Lighting Fixtures 2x20W LED industrial luminaire(tube light) CRCA precoated housing/polycarbonate housing duly prewired with accessories and trans-parent cover of polycarbonate complete with lamp & accessories. IP65 enclosure protection, suitable for installation in Indoor building lighting, building peripheral lighting. Scope of work includes Fabrication and installation of 19 mm dia GI pipe, Approx 1 meter length with mounting hardwares and accessories for mounting / fixing Light Fixtures from ceiling. Light fixtures shall be suitable for Loop-in Loop-out connections. The supply shall inclusive of cable gland for Incoming & outgoing cables. This shall include transportation from owner's issue point to actual place of installation by contractor's own lifting & transporting arrangement, unpacking, assembly of luminaries, drilling etc. as required, all labour and material complete as per drawings, specification of this tender and directions of Engineer-in-charge.

SUPPLY & INSTALLATION OF WELDING SOCKETS AND CONVENIENCE RECEPTACLES

Supply, Installation (ceiling / wall mounting as per installation standard), earthing, glanding, termination of incoming and outgoing cables/ wires, testing and commissioning of 5/15A, 240V AC, 1 Ph, 3 Pin (Ph+N+E) Convenience Socket Outlet, decorative indoor type, 2 mm thick CRCA Sheet steel enclosure material, IP55 with canopy, with "ON-OFF" Type rotary switch, SS material name plate, Interlock type (Suitable Mechanical & Electrical interlock arrangement will be provided, so as to break the electrical circuit before the plug is completely withdrawn & make the circuit after the plug is fully inserted. Interlock shall be such that, it is not possible to insert or withdraw the plug with the switch in "ON" position. Suitable for Loop-in Loop-out connections including supply of cable gland for Incoming & outgoing cables. The socket shall be suitable for termination of 3C X 4 sq mm cu cable. This shall include transportation from owner's issue point to actual place of installation by contractor's own lifting & transporting arrangement, unpacking, assembly of luminaries, drilling etc. as required, all labour and material complete as per drawings, specification of this tender and directions of Engineer-in-charge.

Supply, Installation (ceiling / wall mounting as per installation standard), earthing, glanding, termination of incoming and outgoing cables/ wires, testing and commissioning of 63A, 415V AC, 3 Ph, 5 Pin (3Ph+N+E) Welding Socket Outlet, 2 mm thick CRCA Sheet steel enclosure material, IP55 with canopy, with "ON-OFF" Type rotary switch, SS material name plate, Interlock type (Suitable Mechanical & Electrical interlock arrangement will be provided, so as to break the electrical circuit before the plug is completely withdrawn & make the circuit after the plug is fully inserted. Interlock shall be such that, it is not possible to insert or withdraw the plug with the switch in "ON" position. Suitable for Loop-in Loop-out connections including supply of cable gland for Incoming & outgoing cables. The socket shall be suitable for termination of 3.5C X 50 sq mm Al cable. This shall include transportation from owner's issue point to actual place of installation by contractor's own lifting & transporting arrangement, unpacking, assembly of luminaries, drilling etc. as required, all labour and material complete as per drawings, specification of this tender and directions of Engineer-in-charge.

SUPPLY, INSTALLATION, TESTING AND COMMISSIONING OF CEILING FAN AND EXHAUST FAN

Supply, Installation, testing and commissioning of 240V AC, 1 Ph, 80 Watt, 48" Industrial type Ceiling Fan of Bajaj / Havells / CGL Make. Scope of work includes Fabrication and installation of 19 mm dia GI pipe, Approx 1 meter length with mounting hardwares and accessories for mounting / fixing Ceiling Fan from ceiling. Fan from ceiling. Fan shall be suitable for Loop-in Loop-out connections including supply of cable gland for Incoming & outgoing cables of 3C X 2.5 sq mm size. This shall include supply of SS materials mounting accessories like : Nut, bolts and other necessary accessories.

Supply, Installation, testing and commissioning of 240V AC, 1 Ph, 8" Industrial type Exhaust Air Fan of Bajaj / Havells / CGL Make. Suitable for Loop-in Loop-out connections including supply of cable gland for Incoming & outgoing cables of 3C X 2.5 sq mm size. This shall include supply of SS materials mounting accessories like : Nut, bolts and other necessary accessories.

SUPPLY AND INSTALLATION OF POINT WIRING INSIDE BUILDINGS

Supply, installation and connection of point wiring for lighting fixture with 2.5 sq.mm PVC insulated, FRLS, copper wire in 25 mm dia PVC conduit (including supply of 2.5 sq.mm PVC cu wire, supply of PVC conduit, junction boxes) for concealed wiring including all accessories on surface or in recess, including circuit wiring, earthing of light fixture with 2.5 sqmm PVC insulated FRLS, copper wire etc. as required. The above scope includes cutting, chasing of wall and filling the chases with mortar and making good finish as required. Supply of wire from Lighting Distribution board will also form part of point wiring and will not be paid separately. The scope of work (including supply of cables) will start from outing terminals of Lighting Panels.

Supply, installation and connection of point wiring for 3 pin 5/15A switch socket outlet with 4 sq.mm PVC insulated, FRLS, copper wire in surface (in 25mm dia.GI conduit) / recessed (in 25 mm dia PVC conduit) (including supply of 4 sq.mm PVC cu wire, supply of PVC conduit, junction boxes) including all accessories on surface or in recess, including earthing of 3rd pin with 4 sqmm PVC insulated FRLS single core copper wire etc. as required. The above scope includes cutting, chasing of wall and filling the chases with mortar and making good finish as required. Supply of wire from Distribution board will also form part of point wiring and will not be paid separately. The scope of work (including supply of cables) will start from outing terminals of Lighting Panels.

SUPPLY AND INSTALLATIONS OF EARTHING MATERIALS

ELECTRICAL EARTH PITS

Supply, Installation, connection of 40 mm dia & 3000 mm long GI ROD electrode. Supply, Installation, connection to main earth grid, testing and commissioning of earth pits in hard soil area complete with 40 mm dia & 3000 mm long GI ROD electrode, GI test link, concrete chamber with Cast Iron (CI) cover as inspection chamber including excavation of earth pit. supply of civil material, back filling, numbering of pits, including all labour and materials as per standard drawing complete as per specification of this tender and directions of Engineer-in-charge.

EARTH PIT MARKER

Supply, Casting and installation of earth pit markers for directly buried earth electrode including supply of cement and associated materials including engraving "BURIED EARTH ELECTRODE NO." complete with support & foundation, painting & supply of paint as per approved drawing, specification of this tender and directions of Engineer-in-charge.

SUPPLY & LAYING / INSTALLATION, CLAMPING AND CONNECTION OF GI EARTH CONDUCTORS FOR EARTHING NETWORK

Supply, Laying / Installation, clamping and connecting of 75X10 mm GI earth conductors for Main Earthing Grid including excavation and filling of earth, chipping and remaking of concrete surface, supply and fixing of GI clamps, Supply of fixing GI fastners at earth plate & at equipment end wherever required. Supply & applying bitumin paint & hessian tape on underground joints & cold zinc spray on aboveground joints. Earthing to be carreid out as per IS:3043 It also includes any modification work because of fouling with under ground/above ground piping.

Supply, Laying / Installation, clamping and connecting of 50X6 mm GI earth conductors and connection to Earthing Grid including excavation and filling of earth, chipping and remaking of concrete surface, supply and fixing of GI clamps, Supply of fixing GI fastners at earth plate & at equipment end wherever required. Supply & applying bitumin paint & hessian tape on underground joints & cold zinc spray on aboveground joints. Earthing to be carreid out as per IS:3043 It also includes any modification work because of fouling with under ground/above ground piping.

Supply, Laying / Installation, clamping and connecting of 25X6 mm GI earth conductors and connection to Earthing Grid including excavation and filling of earth, chipping and remaking of concrete surface, supply and fixing of GI clamps, Supply of fixing GI fastners at earth plate & at equipment end wherever required. Supply & applying bitumin paint & hessian tape on underground joints & cold zinc spray on aboveground joints. Earthing to be carreid out as per IS:3043 It also includes any modification work because of fouling with under ground/above ground piping.

Supply, Laying / Installation, clamping and connecting of 400 x 75 x 10mm GI Earth Bus / Plate and connection to Earthing Grid including excavation and filling of earth, chipping and remaking of concrete surface, supply and fixing of GI clamps, Supply of fixing GI fastners at earth plate & at equipment end wherever required. Supply & applying bitumin paint & hessian tape on underground joints & cold zinc spray on aboveground joints. Earthing to be carreid out as per IS:3043 It also includes any modification work because of fouling with under ground/above ground piping.

GI PIPE SLEEVES

SUPPLY, FABRICATION AND INSTALLATION OF GI PIPE SLEEVES

Supply, fabrication and Installation of of 19 mm dia, 1 meter length, class B, GI pipes including supply of SS materials hardwares (like : Nut, bolts) for mounting lighting fixtures / ceiling fan from ceiling / structures

Supply, fabrication and Installation of 150 mm dia class B, GI pipes sleeves for cable entry / laying in substation building and Fabrication and installation of 150 mm dia class B, GI pipes sleeves for cable protection, fixed on steel, concrete or similar structure, in trenches, ready to be buried in concrete including cutting, bending, grinding, threading and similar works, supply & fixing of required GI fastners, clamps, small iron structures, spacers, cleats, plug, bushings, sealing compound/ material etc., cutting and remaking of concrete surface including supply of civil material, all labour and materials complete as per approved drawings, specification of this tender and directions of Engineer-in-charge.

ANCHOR FASTENERS

Supply, drilling in RCC and fixing of 8 mm dia metallic anchor fasteners for mounting light fixtures from ceiling including all labour and materials, as per specifications of this tender and directions of Engineer-in-Charge.

North East Engineering n Construction

Tuaman Engineering Limited

Chicago Construction Co

PUNJAB ENGINEERING COMPANY (PROJECT DIVISION)

Chicago Construction Co

North East Engineering n Construction

Tuaman Engineering Limited

PUNJAB ENGINEERING COMPANY (PROJECT DIVISION)

R B Engg and Infrastructure Pvt Ltd

North East Engineering n Construction

Tuaman Engineering Limited

PUNJAB ENGINEERING COMPANY (PROJECT DIVISION)