SPECIAL REPAIRS TO BLDG NO. 94 (OR MARRIED ACCN ) KALIDHARI LINE AT 14 GTC SUBATHU UNDER GE KASAULI

Amount

Demolition of cement concrete (un re-inforced) in ground floor and paving n.exc. 15 cm thick below or above ground level complete all as specified .

Demolition of reinforced cement concrete (reinforcement cut as required to facilitate demolition) complete all as specified.

Dismantling wrought iron or mild steel work of any description not otherwise provided for complete all as specified.

Dismantling PVC drain or vent pipe of any description in any position including bends branch pieces etc. Complete all as specified.

Taking down cement plaster on brick wall surfaces etc including raking out joints hacking for key, scrubing down with water etc cpmplete all as specified.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) and removing rubbish off the premises complete all as specified.

Demolition of stone slabs and tiles of any description or thickness in floors aprons etc laid bedded and pointed in any mortar complete all as specified.

Demolition of brick work or stone boulder masonry built in cement mortar complete all as specified.

Taking down chowkhats or frame with shutter (without taking off shutters from the frames) n.exc. 1.5 Sqm complete all as specified.

Taking down chowkats or frames with shutters (without taking off shutters from the frame ) exceeding 1.5 sq.m and not exc 4.00 sq.m each and making good the disturbed surfaces complete all as specified.

Dismantling plain or corrugated steel sheeting any guage thickness including Nainital pattern as in roof covering complete all as specified.

Brick work with sub class 'B' bricks of class designation 10 all as per IS-1077-1992 (minimum compressive strength of brick 100 kg/Sqcm) old size bricks, straight or curved on plan exceeding 6 mtr mean radius built in CM 1:6, complete all as specified.

Rendering 10 mm thick on other than fair faces of brick work in CM 1:6 finished even and smooth with out using extra cement complete all as specified.

Plain Cement concrete 1:2:4 type B-1 (using 20mm graded stone aggregate) as in seismic and other similar bands, shelves, copings, bed plates, hold fasts, plinth courses, filling in pressed steel frame and the like finished fair and even including necessary form work complete all as specified.

50mm thick plain cement concrete 1:3:6 type C-1 (using 20mm graded stone aggregate) as in plinth protection finished fair and even without using extra cement complete all as specified. Note:- Plinth protection shall be laid in panels and length of the each panel shall not be more than 2.00 mtr. 6mm joints filled with 85/25 grade bitumen and sand (1:3 ratio) shall be provided. No deduction for joints shall be made while making payment for this item.

RCC 1:2:4 type B-1 (using 20mm graded stone aggregate as in shelves / slabs and like complete all as specified.

PCC 1:3:6 type C2 (using 40mm graded stone aggregate) as in surface channel / drains complete all as specified.

Extra for forming fair finished drain or channel 30 cm inner girth in forms, moulds/stopped ends etc. complete all as specified.

Mild steel TMT Bars 10mm dia and over cut to length, bend to shape required, including cranking, bending, for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips complete all as specified.

Pre- painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50 mm thick of any colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall, ridges etc. fixed with self tapping screws of length not less than 50mm complete all as specified.

Pre- painted galvalume aluminum zinc coating GI based plain steel sheet 0.50 mm thick of any colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall, ridges, flashing, eaves board valley gutter of any shape etc, cut to designed shape (Jhhallar) as directed at site fixed with self tapping screws complete all as specified.

Aluminium flat sections as in wind tie complete all as specified.

Non Skid coloured ceramic tiles 8 mm thick area of each tile exc 0.18sqm n exc 0.38 sqm in floors, set and jointed in neat cement slurry and pointed in white or colored cement to match with the tiles over and including 15mm thick screed bed or bedding layer in C.M 1:4 etc complete all as specified.

Non Skid coloured ceramic tiles 8 mm thick in skirting, set and jointed in neat cement slurry and pointed in white or colored cement to match with the tiles over and including 10mm thick backing coat in C.M 1:3 etc complete all as specified.

First quality joint free Non Skid ceramic tiles (coloured) 400x400x 7 to 8mm thick (square/rectangular) as in floors set and jointed in cement slurry and pointed in coloured cement over and including screed bed 1or bedding layer of mortar 15mm thick in CM (1:4) complete all as specified.

Coloured glazed ceramic tiles in vertical surface 350 x 250 x 7mm / 450 x 350 x 7mm thick set & jointed in neat cement slurry and pointed in white or coloured cement to match including 15mm thick backing coat in CM 1:6 complete all as specified.

Pressed steel frames of size 125 x 60 mm with one or more rebates including necessary fixing lugs, hinges, lock strike plate etc. complete, as specified.

Steel windows with side hung shutters including projecting type hinges with steel handle , and steel peg stay , complete with glazing bars , dovetailed or welded complete all as specified.

Steel windows with side hung shutters including projecting type hinges with steel handle , and steel peg stay , complete without glazing bars , dovetailed or welded complete all as specified.

Steel ventilator with top hung shutter including hinges, steel peg stay, complete all as specified.

Framed work such as grills, gratings, etc with ends of bars shouldered and / or riveted, or forged into spikes , framed guard bars, barred iron doors, ladders, framed balusters, walk ways, railings , framework of water tanks and similar work conforming to Fe 290 Gde E-165 complete all as specified.

Galvanised mild steel wire cloth, 0.63mm nominal dia of wire and average width of aperture 1.40mm and fixed with tinned tacks, or galvanised wire staples complete all as specifeid.

Sheet glass 3 mm thick ordinary quality & glazing with oil putty in square n. exc 0.5 Sqm in each pane complete all as specified.

Figured glass 4mm thick, pin head type and glazing with oil putty in square n. exc 0.5 Sqm in each pane complete all as specified.

35 mm thick second class hard wood factory made kiln seasoned chemically pressure treated plain, framed, panelled shutters with lock rail and panels of 9mm thick commercial ply or 12mm thick veneered particle board commercial veneered on both sides, including priming coat, duly hammer marked. The size of rail & style shall be as per IS 1003 part-1 complete all as specified.

30 mm thick second class hard wood factory made kiln seasoned chemically pressure treated glazed and gauged skeleton shutters open rebated and prepared to receive glass, gauge etc with sash bars edges of framing plain chamfered or rounded fitted with cut and mitred beads for securing glass etc including priming coat. The size of member of shutters as specified in MES Schedule Part-1 Section 8 clause 8.20 (a) complete all as specified.

Mild Steel works as in bands straps, hold fasts etc, conforming to IS-2062 (Fe-290), embedded portion duly painted with bituminious paint and sanded, complete all as specified.

Factory made solid PVC door frame of size 50mmx47mm made out of 5 mm wood grain printed PVC sheet reinforced with MS square tube etc complete all specified.

Factory made solid PVC moulded door shutter 28 to 30 mm thick (stiles) with 2, 4 (or) 6 raised panel design with 2 mm thick 3D wood grain moulded PVC sheet polyurethane painted on the front face and 2 mm plain colour PVC sheet on back face with particle board core etc complete all specified.

20 mm dia aluminium anodised curtain rails with fixing brackets etc complete all as specified

Second class hard wood small fittings such as brackets of any type latch and hinge blocks shaped door and window stops and the like, including all necessary labour, articles n.exc. 200 cu cm each complete all as specified.

Cold rolled mild steel medium weight butt hinges 100mm, ISI marked, complete all as specified.

200 mm long aluminium anodised barrel tower bolts of extruded section complete all as specified.

150 mm long aluminium anodised barrel tower bolts of extruded section complete all as specified.

125 mm long aluminium anodised handles extruded type complete all as specified.

300 mm long aluminium anodised sliding door bolt with hasp, staple (bolt type) and fixing clip of sheet, cast or extruded sections, bolt not less than 12mm dia with and including minimum of 6 bolt and nuts ,fixed on plate or staple plate complete all as specified.

Preparation of new plastered surfaces of walls and applying two coats of oil emulsion distemper over a coat of primer complete all as specified.

Preparation of plastered or unplastered old decorated surfaces with sand papering of walls including cornices etc. including washing, rubbing down and stoping the connected previously treated surfaces and applying one coat of teraccota complete all as specified.

Preparation of old painted wood or wood based surfaces of any description not otherwise described over 10 cm width or girth and applying one coat of synthetic enamel paint complete all as specified.

Preparation of new or previously untreated surfaces of wood or based materials of any description not otherwise described, over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified.

Preparation of new steel surfaces of any description not otherwise described over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified.

Preparation of old painted steel surfaces of any description not otherwise described over 10 cm width or girth and applying one coat of synthetic enamel paint complete all as specified.

Taking up or down 15 mm dia steel tubing and connection and removal from site complete all as specified.

Taking up or down 20 mm dia steel tubing and connection and removal from site complete all as specified.

Steel water tubing 15 mm bore medium grade galvanized with all fittings and fixed complete to walls and ceiling or laid into floor complete all as specified.

Steel water tubing 20 mm bore medium grade galvanized with all fittings and fixed complete to walls and ceiling or laid into floor complete all as specified.

Taking up or down steel tubing and connections cleaning for refixing and refixing old steel tubing and connections in new or in old position (walls ceiling floor etc) of 20 mm bore of pipe complete all as specified.

Taking up or down steel tubing and connections cleaning for refixing and refixing old steel tubing and connections in new or in old position (walls ceiling floor etc) of 15 mm bore of pipe complete all as specified.

15mm bib tap cast copper aloy with crutch or butterfly handle screwed down screwed for iron pipe or for brass ferrule and fixed in repair complete all as specified.

Viterous china WHB (flat back or angle back) any size, including cutting for and pinning in ends of brackets complete with 32 mm bore PVC waste pipe complete all as specified.

15mm pillar tap cast copper alloy chromium plated with capston heads screwed down screwed for iron pipe or for brass ferrule and fixed in repair complete all as specified.

Brass chromium plated tubular towel rail 20 mm dia complete all as specified.

Dismantling water tanks n.exc 500 litres capacity and removing to store complete all as specified.

500 litres capacity rotational moulded polythene water stoarage tanks (clyndrical vertical with closed top) triple layered hoisted and fixed in position complete all as specified.

20mm dia ball brass valves, high pressure with polythene float and flynut complete screwed for iron pipes etc fixed in repair complete all as specified.

10 litres capacity PVC valveless syphonic action type flushing cistern low level white with inlet, ball valve , float including brackets and PVC flush pipe 32mm dia complete all as specified. .

Angle stop valve, brass chromium plated, fancy type, screwed down, high pressure with crutch or butterfly handle screwed down , screwed for iron pipe or for union, suitable for 15mm bore pipe, fixed in repair complete all as specified.

15mm dia PVC connection 450 mm long with brass nut fixed in repair complete all as specified.

Vitreous china squatting pan, "Orissa Pattern" size 580 x 440 mm white with integral foot rest fixed in repair complete all as specified.

Stop valve cast copper alloy 20mm bore screwed down high pressure with crutch or butterfly handle scewed both ends for iron pipe or for union fixed in repair complete all as specified.

110mm dia PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to wall including clamps as required complete all as specified.

75mm dia PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to wall including clamps as required complete all as specified.

75mm dia PVC (SWR) bends with oval access door with rubber ring joints complete all as specified.

75mm dia PVC (SWR) floor trap, plain with grating including jointing with solvent cement including necessary PCC & form work complete all as specified.

75mm dia PVC (SWR) junction single, (single T), equal or un equal with oval access door including jointing with solvent cement as required complete all as specified.

110mm dia PVC (SWR) junction single, (single T), equal or un equal with oval access door including jointing with solvent cement as required complete all as specified.

110mm dia PVC (SWR) branch piece, single, equal or un equal of any length including jointing with solvent cement as required complete all as specified.

75 mm dia PVC (SWR) branch piece, single, equal or un equal of any length including jointing with solvent cement as required complete all as specified.

110 mm dia PVC (SWR) reducer, single, equal or un equal of any length including jointing with solvent cement complete all as specified.

75 mm dia PVC (SWR) vent cowl, including jointing with solvent cement complete all as specified.

20 mm thick black polished granite stone slab of size not less than 1000 x 600 mm as in steps, pillars, window cills, cooking platforms and like, laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab, full rounded off corner/ edges including all cutting to make it square or rectangular, including rubbing and polishing with machine to achieve the desired granite finish over and including 15mm thick cement screed bed in CM (1:6) complete all as specified.

Brass chromium plated soap dish of size 180x160x90mm any type, fixed with chromium plated brass screws fixed in repair complete all as specified.

Sink with drainage board made out of stainless steel sheet 1.0mm thick with plug, washers and wastes, overall size 915mm x 460mm, bowl size 410mm x 330mm x160mm including fixing cantilever brackets and connection to union, pipe, fixed in repairs complete all as specified.

Stainless steel plate rack of size 24"x 36" x 10" made out of 1.00 mm thick sheet ISI marked, fixed in repairs complete all as specified.

19 mm thick pre-laminated particle board exterior grade pre laminated one side with decorative choice lamination and other side balancing white lamination, fixed with screws to timber / steel frame work as in shelves or shutters or wall panelling, fixed in repairs complete all as specified.

Piano hinges, mild steel bright finish width of flap 40mm fixed in repair complete all as specified.

Magnetic catches brass body for use in cup boards of kitchen, ward robes etc. fixed in repairs complete all as specified.

40mm dia brass cupboard knob polished, fixed with nut screw and washer, fixed in repairs complete all as specified.

Brass chromium plated shower rose 125mm with swivel joints fixed in repair to steel pipe or union complete all as specified.

Hasp and staple 75mm, mild steel, wire type, stove enamelled black, including bolt to hinge plate and fixed with screws complete all as specified.

Water proofing treatment to sunken floor of WCs, bathroom etc. comprising of (i) Cleaning of sunken floor surface with mechanical means i.e. wire brush/air blower etc. to remove all loose / unsound material, dirt, dust, etc. (ii) Applying cement slurry mixed with acrylic based polymer modified cementitious composite compound coating Hydroproof Xtra of FOSROC/Equivalent of Dr Fixit of Pidilite Industries Ltd in the ratio of 1:2:4 (One part of acrylic polymer : Two part of water and four part of cement). (iii) First layer of cement slurry @ 0.444 Kg/Sqm mixed with acrylic based modified cementious composite compound @ 0.222 Litre/Sqm and allow it to air dry for 04 hours. (iv) Second layer of cement slurry @ 0.222 Kg/Sqm mixed with acrylic based polymer modified cementitious composite compound @ 0.111 Litre/Sqm and allow it to air dry for 04 hours followed by water curing for 48 hours. (v) 200 micron thick polythene film pasted with help of adhesives over treatment. Note :- Joints of WC/Trap/Soil waste shall be properly sealed with sealing compound. Testing of all traps and joint and sunken slab shall be done as per IS-1742 before filling and tiling work.

Plain cement concrete 1:5:10 type E-2 (using 40mm graded broken brick aggregate) as in foundation, filling and mass concrete, complete all as specified and as directed.

100 mm thick cement concrete 1:3:6 type C-2, (using 20 mm graded stone aggregate) as in sub floors, filling and mass concrete etc complete all as specified.

Chequred cement concrete tiles coloured (300 x300 x 25mm thick) in grey cement and with pigment in floors etc , set and jointed in neat cement slurry, over and including 15mm thick screed bed in cement mortar (1:6) omplete all as specified.

False ceiling with one layer of 'LaGyp' standard boards manufactured by M/S Lafarge Board Gypsum India Pvt Ltd, at all height and levels. Standard boards of size 1220x1830x12.5mm, standard board to be laid on 'LaGyp' universal channel (web 45 mm premanunfacturers specifications metal comprising of "LaGyp" universal channel (web 45 mm and flange 27mm base metal thickness (BMT) 0.55 mm and length 3660 mm to be used as main channel as well as ceiling channel. "LaGyp" connecting clips, perimeter channel ( Size of web 28 mm, flange 18/30 mm and length 3660 mm, MBT 0.55 mm) and "L" angle (Length 3050 mm BMT 0.55 mm) with finally the board are to be Joined and finished so as to have a flush look which includes filling and finishing the tapered and square edges of the board with "LaGyp" easy joint Gypsum based jointing compound, "LaGyp" paper tape and applying two or more coats of oil bound distemper to give a neat and even finish including preparing the base with primer and necessary scaffolding etc complete all as specified.

Taking down carefully copper/Aiuminium point wiring (Light/Fan/Point Socket or power) (fittings such as switches ceiling roses, pendent, regulators, sockets etc to be measured & paid seprately) & making good to disturbed surface of walls/floors etc. complete all as specified.

Point wiring using approved colour coding as per IS with stranded copper conductor single core 1.5 Sqmm (Nominal area), PVC insulated cable FRLSH grade in and including rigid non metallic PVC conduit (ISI marked) including cutting chiseling and grouting concealed PVC conduit pipe, tee, elbow and bend etc.and with all connecting accessories, mild steel sunken boxes suitable for mounting switch/sockets with earth dolly duly painted with two coats of anti corrosive paint over a coat of red oxide primer, mounting frame over cover plate, covered with 3mm thick plastic laminated sheet, PVC insulated copper conductor 1.5 Sqmm (Nominal area) single core cable FRLSH as earth continuity conductor to common earth and connecting to earth dolly for the following complete all as specified:-

One light/fan point controlled by one switch.

One switch socket outlet 3 pin, 5 Amp on the independent board.

One switch socket outlet 3 pin,5 Amp on same board.

One light point controled by 2 two way switches.

One bell/buzzer point controlled by one push button on the same board with other switches

All as per item No. 98 here-in-before but with 2 single core PVC insulated FRLSH and sheathed copper conductor of size 2.5 Sqmm in and including rigid non metallic PVC conduit (ISI marked) including cutting chiseling and grouting concealed PVC conduit pipe, tee, elbow and bend etc.and with all connecting accessories with 2.5 Sqmm PVC insulated FRLSH copper conductor as earth wire and connecting to common earth dolly for 6 pin 16 Amp socket outlet on the independent board complete all as specified.

All as per item No.98 here-in-before but with 2 single core PVC insulated FRLSH and sheathed copper conductor of size 4.0 Sqmm in and including rigid non metallic PVC conduit (ISI marked) including cutting chiseling and grouting concealed PVC conduit pipe, tee, elbow and bend etc.and with all connecting accessories with 4.0 Sqmm PVC insulated FRLS copper conductor as earth wire and connecting to common earth dolly for 6 pin 16 Amp socket outlet on the independent board complete all as specified.

Bell push, 6 Amps, SP, flush type complete all as specified.

Electric Bell , AC 230 volts, single pole complete all as specified.

Switch piano, flush type, single pole 2 way 6 Amp,ISI marked complete all as specified.

Lamp holder,PVC insulated body, with back plate suitable for batten fitting complete all as specified.

Switch piano, flush type, single pole 1 way 6 Amp,ISI marked complete all as specified.

Switch piano flush type, single pole 1 way 16 Amp complete all as specified.

Socket 5 pin 6 Amp piano flush type, ISI marked complete all as specified.

Socket out let 2 in one 6 pin 6 & 16 Amp complete all as specified.

Ceiling rose, 3 phase/ PVC/ polycorbonate,isolated body complete all as specified.

LED bulb 10 watt complete all as specified.

Self Ballasted LED Batten extruded thermoplastic body with PC diffuser in square shape type fitting Pre-wired including LED tube 18/20 watt 6500K 4 ft IP20 linear LED Basic all purpose surface and wall mounted led batten with polycarbonate housing & integrated electronic driver complete all as specified. Make: Philips Cat No BN 021 LED25S 6500 PSU GR S1 or its equivalent in the makes mentioned in Appendix 'B'.

Decorative wall light fixture fancy type, made out of Polycorbaonate,suitable for B-22 base holder fixed as in repair complete all as specified. Make: Polycab product code PGR0301010 or its equivalent in the makes mentioned in Appendix 'B'.

Sleek LED mirror light with diffuser 7/ 9 watt along with all accessories prewired including connecting with copper flexible cable of size 0.7 Sqmm 3 core complete all as specified. Make: Wipro Cat No LL20-111-XXX-65-NE or its equivalent in the makes mentioned in Appendix 'B'.

Bulkhead luminaire decorative energy saving new generation 10W LED IP65 with opal diffuser including electronic driver & connection with copper flexible cable 3 core complete all as specified. Make Philps Cat No WT202W LED6S NW PSU S2 PC or its equivalent in the makes mentioned in Appendix 'B'.

LED building security light 25 /30 watt pressure die cast housing with individual LEDs & Lens with modular secondary optics and IP65 protection with electronic driver and copper conductor 3 core of 0.7 sqmm from ceiling rose to security light with bracket made out of GI light grade pipe 32 mm bore 1.5 mtr long bend to an angle of 120 degree with fixing arrangements fixed in repair on wall complete all as specified. Make: Wipro Cart No LR02-331-XXX-57-XX or Philips or its equivalent in the makes mentioned in Appendix 'B'.

Wall mounting LED fitting 9/12 watt 6500K 2 ft basic all purpose surface and wall mounted led batten with polycarbonate housing & integrated electronic driver complete all as specified. Make: Philips cat No.BN021C LED20S PSU CW GR S2 or its equivalent in the makes mentioned in Appendix 'B'.

Sheet metal enclosure with double door SPN DBs conforming to IS:8623.III , IP:43 protection, shrouded neutral bar and cement spill protector, 8 way, 240 Volt complete all as specified.

Sheet metal enclosure with double door for DBs conforming to IS:8623.III , IP:43 protection, shrouded neutral bar and cement spill protector, 4 way, 415 Volt TPN complete all as specified.

MCB 'B' characteristics, double pole , 240 V, 32 Amp breaking capacity 10 kA complete all as specified.

MCB 'B' characteristics, four pole , 415 V,63 Amp breaking capacity 10 kA complete all as specified.

MCB B characterstic single pole 5 to 30 Amp, 240 volt breaking capacity 10 kA complete all as specified.

Submain wiring with 2 single core PVC insulated FRLS cable 6 Sqmm copper conductor PVC sheathed in and including rigid non metallic PVC concealed conduit heavy duty of suitable size including cutting chiseling of wall and making good to disturbed surface of walls / floor etc to match with the existing finishes, drawn with 6 Sqmm PVC insulated FRLS copper conductor cable for earth wire fixed with saddle and connecting to common earth teriminals complete all as specified. Note : Three runs of 6 sq mm cable and one run of PVC conduit shall be measured as one length.

Blanking plate complete all as specified.

Single pole and neutral sheet metal enclosure with a 2 pin and earth plug and socket complete with one single pole MCB 20 Amps complete all as specified.

Non mettalic electric meter box of size 250 x 200 x 105 mm with single hinged door for 01 No. single phase meter of after disconnecting the supply of electric meter and fixing the electric meter on meter box including reconnecting the electric supply complete all as specified. Make: Sintex Cat No. GSMB 2520 or its equivalent in Hensel / Clipsal

Earthing with galvanised steel earth plate electrode 60 cmx 60cm x 6 mm thick surrounded by mixture of charcoal and salt in alternate layers , buried directly in ground vertically in a pit of depth not less than 2.25 meter deep below ground level with top edge of the plate at a depth of not less than 1.5 mtrs below normal ground level connected to galvanized iron or steel earth lead wire 4.0 mm dia,( No 8 SWG) by means of bolts ,nuts, check nuts and washers of galvanised iron or steel earth wire protected by galvanised steel pipe 15 mm bore (light grade) and connected to main switch or main control board all as shown in electrical plate No. 3 of MES Schedule Part -I 2009 including necessary excavation and earth work in any type of soil, 20 mm bore GI pipe (Light grade ) for watering , protection pipe, funnel, wire mesh , PCC 1:2:4 type B1 chamber in cement concrete ,50 mm thick precast RCC M-25 ( Normal mix) cover duly reinforced with XPM (weight not less than 3 kg /sqm ) and CI frame etc , and including provision of test point , connecting to test point and testing on completion etc, complete all as specified. NOTE : The unit rate quoted shall include earthing lead and protection pipe upto 7.5 metre from top of earth plate.

RAJESH BUILDERS

Babu Ram Sud and Sons

S.R.AND CO.

M/S SHANTI SARUP DINESH CHAND

M/S SK Sharma & Co.