GE S U 03 2022 23 SPECIAL REPAIR TO CERTAIN BLDGS CONSTRUCTION OF STORAGE SHELTER ADDN ALTN TO TOILET ROOM AND PROVISION OF COLLAPSIBLE GATE UNDER GE SOUTH UDHAMPUR

Amount

Demolition of reinforced cement concrete in roof floor (other than ground floors) beams staircase, landing chajja and similar work complete all as specified and directed.

Demolition of cement concrete (unreinforced) exceeding 15 cm thickness (above ground floors) complete all as specified and directed.

Demolition of cement concrete (unreinforced) in ground floor and in paving not exceeding 15 cm thickness (below or above ground level) complete all as specified and directed.

Brass chromium plated fancy type wall mixer 15mm bore for mixing Hot & Cold water screwed down for iron pipe, fixing in repair complete all as specified and directed.

Glazed coloured ceramic tiles in dado/vertical surface (350mm x 250mm x 7 mm /450mm x 300mm x 7mm thick set and jointed in neat cement slurry and pointed in coloured cement to match the surface complete including taking down of wall tile complete all as specified and directed.

Non skid coloured tiles (square/rectangular) 7 to 8 mm thick area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm, in floor etc set and jointed in neat cement slurry and pointed in white or coloured cement to match the surface complete all as specified and directed.

All as per srl item No. 6 above but in vertical surfaces complete all as specified and directed.

Non skid coloured tiles (square/rectangular) 7 to 8 mm thick area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, in floor etc set and jointed in neat cement slurry and pointed in white or coloured cement to match the surface complete all as specified and directed.

All as per srl item No. 8 above but on vertical surfaces as in skirting complete all as specified and directed.

25mm thick cement concrete 1:2:4 type B-0 using 12.5mm graded crushed stone aggregates as in floor and finished even and fair complete all as specified and directed.

Screed bed or bedding layer of mortar 15 mm thick in cement mortar 1:4 laying floor finishes complete all as specified and directed.

15mm thick rendering on fair faces of brick / concrete surfaces in cement mortar 1:4 and finished even and fair for receiving tiles on vetical surface complete all as specified and directed.

Machine cut kota stone slab flooring 18-20 mm thick over cement screed and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete including 15mm thick cement mortar 1:4 complete all as specified and directed.

Machine cut kota stone 18-20 mm thick in riser of steps, skirting, dado and pillar laid over cement screed and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and directed.

150 mm wide strip of makrana white marble 14-16mm thick machine cut, bedded jointed and pointed with grey cement slurry including cutting and polishing complete all as specified and directed.

Taking down cement plaster, any description on brick or stone or cement concrete walls including raking out joints, hacking for key, scrubbing down with water complete all as specified and directed.

Marble work 14 to 16mm thick (table rubbed and polished) in steps,jambs,pillars,window cills,cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with marble shade.(shade and type as approved by GE) complete all as specified and directed.

Moulding of kota /marble stone full round complete all as specified and directed.

Screed bed or bedding layer of mortar 20mm thick in cement mortar 1:4 laying floor finishes complete all as specified and directed.

Rendering 15mm thick on brick work or concrete surfaces in cement mortar 1:4 finished even and smooth without using extra cement including mixing integral water proofing compound in the proportion as mentioned in manufacturer's instructions complete all as specified and directed. (Water proofing compound to be measured and paid for separately).

Rendering 15mm thick on brick work or concrete surface in cement mortar 1:6 finished even and smooth without using extra cement complete all as specified and directed.

Rendering 10mm thick on brick or concrete surface as in ceiling in cement mortar 1:3 finished even and smooth without using extra cement complete all as specified and directed.

Supply only integral water proofing compound complete all as specified and directed.

Taking down chowkats or frames with shutters (without taking off shutters from frames) area not exceeding 1.50 Square Metre each, including cutting holes for taking out hold fasts or dismantling brick work (holes cut and any other damage to jambs, walls for taking out hold fast shall be finished identical to existing finish without any extra cost to Govt) complete all as specified and directed.

Taking down chowkats or frames with shutters (without taking off shutters from frames) area exceeding 1.50 square metre and not exceeding 4.0 square metre each, including cutting holes for taking out hold fasts or dismantling brick work (holes cut and any other damage to jambs, walls for taking out hold fast shall be finished identical to existing finish without any extra cost to Govt.), complete all as specified and directed.

Solid frame wooden high density filament (HDF) double rebated of size 125 mm x 55 mm processed with polyole fins and different wood fibre, fixed to opening including necessary lugs, hinges, lock strike plate etc complete all as specified and directed. Make - HR Enterprises/Polycon/Rajshree/ plastiwood

Solid PVC door frame wood grain colour coated of size 50mm x 95mm made out of 5 mm wood grain colour PVC sheet reinforced with MS Square tube supply and fixing as per specification and drawing complete all as specified and directed.

Factory made solid UV wood grain printed panelled/plain PVC single piece door shutter 30 mm thickstyle,consisting of frame made out of MS tube 19 gauze thickness & size of 25mmX25 mm for sities, top and bottom rail MS frame shall have a coating of steel primer,the frame shall be covered with heat moulded wood grain UV printed PVC sheet tape fixed in MS frame welded sealed to the styles and rail with suitable PVC sheet Beading and jointed toghther with solvent cement complete all as specified and directed and as per manufactures specification drawing. Make : M/s H R Enterprises,, Pathankot, Door Craft Industry Delhi, M/s Trehan Doors Pathankot, Note : The shutter is to be fixed with 50 mm size self drilling star screws full threated.

35mm thick HDF prelaminated (wenga/teak colour) moulded shutter 35mm thick puf (poly ucrane form) insulation with minimum density 40 kg/cum filled in between two HDF sheets of thickness 3.2 mm both & border covered with 10mm thick PVC sheet complete in all respect with lock rail & beautified by PVC bedding all around with PVC Solvent complete all as specified and as directed.

Pre-laminated 18mm thick lead free factory made 100% solid WPC (wood polymer composite) sheet having high natural fiber content 25 to 30% wood colour sheets with density not less than 500 kg/cum and the weight of sheet of 1 Sqm should be 11 kg (+/- 5%) manufactured by ISO 9001-2015 certified company. The sheet should be 100% water proof, termite proof, fire ratardant, manufacured by single layer extrusion process with exellent screw holding capacity and shore D hardnes complete all as specified and directed.

19mm thick ISI, termite proof , chemically well pressed, prelaminated particle board exterior grade prelaminated, one side with decorative choice lamination and other side balancing white lamination fixed with screws to frame work for kitchen cabinet stand cup boards etc including 6mm thick teak wood beading all around complete all as specified and directed. Make:- Win Tuff or its equivalent approved by GE.

S & F 34/35mm thick factory made single piece wire gauge door/shutter solid PVC UV printed doors-wood Free consisting of 5mm thick solid PVC sheet on both side (both side multi color UV printed) using steel/aluminium XPM/wire mesh and consisting frame made out of M.S. tubes of 19 gauge thickness and size of 19mm x 19mm for stiles and 19mm x 19mm for the top, bottom and lock rails with PVC beading in all around M S frame shall have a coat of metal primers. MS frame shall be covered with heat moulded (Rigid) 20/22mm PVC solid sheet at styles, top rail and bottom rail (Rigid) MS Frame welding sealed to the style and with suitable PVC Sheet beading and joined tothether with solvent complete as directed and as per manufature's specification & instructions. Make : M/s HR Enterprises Pathankot, Door Craft Industry Delhi, M/s Trehan Doors Pathankot. Note : The shutter is to be fixed with 50mm size self drilling star screws full threated.

Steel window (box type) factory made with side hung shutters including pintol hinges, steel handles, steel peg stay and all locking arrangement complete with glazing bars dovetailed or welded including one shop coat of red oxide primer complete all as specified and directed. Note : i) The window shall be fabricated as per Drg No CEUZ/TD/1269/2008 Sheet 1/3 to 3/3 ii) MS fillets, glazing, wire gauge shall be measured and paid separately.

Description all as per item No 33 as above here in before but without glazing bar complete all as specified and directed. Note : i) The window shall be fabricated as per Drg No CEUZ/TD/1269/2008 Sheet 1/3 to 3/3 ii) MS fillets, glazing, wire gauge shall be measured and paid separately

S&F factory made mild steel ventilators box type with upper top hung shutters and bottom fixed type shutters including pintol hinges,steel peg stay and one shop coat of red oxide primer complete all as specified and directed. Note : i) The window shall be fabricated as per Drg No CEUZ/TD/1302/2009 Sheet 1/3 to 3/3 ii) MS fillets, glazing, wire gauge shall be measured and paid separately

Mild steel framed work such as grills, gratings, etc. with ends of bars shouldered and/or riveted or forged into spikes, framed guard bar; barred iron doors, ladder, framed balusters; railing;frame work for water tanks and similar work conforming to Fe 290 Gd E-165 complete all as specified and directed.

3 mm thick sheet glass ordinary quality and glazing with oil putty or wooden beads in squares not exceeding 0.50 Sqm in each pane complete all as specified and directed.

3 mm thick sheet glass frosted ordinary quality and glazing with oil putty or wooden beads in squares not exceeding 0.50 Sqm in each pane complete all as specified and directed.

S & F stainless steel wire cloth 0.36mm nominal dia of wire and average width of apreture 1.40mm and fixed with tinned teaks or wire staple complete all as specified and directed.

M&L for plain, solid, straight chowkats and frames of 2nd class Hard wood, wrought, framed rebated on the soild, rounded or chamfered, put together with glue pinned at joints, supplied and fixed complete all as specified and directed.

Demolition of brick/stone masonry built in CM. complete all as specified and directed.

Brick work with sub class B bricks straight or curved on plan to any radius built in CM 1:6 complete all as specified and directed.

Brick work with sub class B bricks straight or curved on plan to any radius built in CM 1:6 but except bricks complete all as specified and directed.

Half brick work with sub class B bricks straight or curved on plan to any radius built in CM 1:4 complete all as specified and directed.

Providing cement concrete 1:2:4 type B-0 (12.5mm graded crushed stone aggregates) as in steps, seismic and other similar bands, parapets and railings up to 60 cm in height, coping, kneelers apex stones , bed plates, kerbs not provided for including weathering, slightly rounded or chamfered angles complete all as specified and directed.

Roughing surfaces of old concrete by picking up, sweeping,cleaning and washing down with water to remove dust etc including taking down tarfelt and brushing neat cement slurry @3kg/Sqm including 20mm thick screeding in CM (1:4) finished even and smooth mixed with water proofing compound complete all as specified and directed. (WPC shall be measured and paid separatley)

Applying bituminous primer on roof surfaces @ 0.40 ltr/Sqm and applying one coat of hot blown bitumen of grade 85/25 @ 1.20 Kg/Sqm and laying polymeric water proofing membrane 3 Kg/Sqm and bonded completely to the surfaces with overlap of 10 cms (overlaps to be thermo fused by flame) and applying one coat of hot blown bitumen 85/25 @ 0.70 Kg/Sqm complete all as specified and directed.

Machine pressed cement concrete tiles 20cm x 20cm x 20mm thick set jointed in neat cement slurry in floors with grey cement and no pigment over 15mm thick screed bedding layer of cement mortar 1:4 complete all as specified and directed.

Providing 50 mm thick cement concrete 1:3:6 type C-1 using 20mm graded crushed stone aggregates as in plinth protection finished even and smooth without using extra cement and providing joints throughout the thickness of the plinth protection filled with mastic filling comprising one part of bitumen 85/25 grade and three parts of sand by weight complete all as specified and directed.

Mild steel sliding door bolt plate type 250 mm long stove enamelled black with bright bolt not less 12 mm dia bolt with and including a minimum of 6 bolts and nuts, four on bolt plate and two on staple plate complete all as specified and directed.

Continuous M S CP piano type hinges 30mm flap (when opened), bright finish or electrogalvanised complete all as specified and directed.

Mild steel pressed steel handle, oval type, stove enamelled black 150 mm long complete all as specified and directed.

100mm size hasp and staple safety type aluminum anodized with mild steel hinges pin including bolt to hinge plate and fixed with screw complete all as specified and directed.

150mm size aluminium anodised barrel tower bolt of extruded section and fixed complete all as specified and directed.

150mm size aluminium anodised handle of febricated type and fixed complete all as specified and directed.

Second class hard wood small fittings such as brackets of any type, shaped door and window stops and the like including all necessary Labour; articles not exceeding 200 Cum each complete all as specified and directed.

Supply and fixing of mild steel cold rolled butt hinges medium weight 100 mm log fixed to steel /angle iron frame by welding if required complete all as specified and directed.

All as srl item No 58 above but 75mm complete all as specified and directed.

All as srl item No 58 above but 50mm complete all as specified and directed.

300mm mild steel ordinary rat tail rod pattern springs, including roller and roller plate complete all as specified and directed.

Mild steel barrel tower bolts, stove enamelled black, with bright bolt 200mm long complete all as specified and directed.

Harrison curtain rails, mild steel, chromium plated with fixing brackets, stops, rollers etc. complete all as specified and directed.

Vitreous China wash basin, white, flat back, size 550mm x 400mm excluding tap, chain, plug but including brackets, waste fitting 32mm dia ,brass chromimium plated for glazed ware sink, basin,with long screwed shanks and fly nuts flange end bedded in red lead cement and other end fixed complete all as specified and directed.

Fancy type pillar taps, cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly nuts, screwed for iron pipe and fixed of bore dia 15mm complete all as specified and directed.

Preparation of wooden surfaces exceeding 10 cm width or girth and applying two coats of synthetic enamel paint over one coat of pink primer complete all as specified and directed.

Preparation of steel and iron surfaces exceeding 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of primer complete all as specified and directed.

Applying 1 mm thick layer of wall putty on walls to give uniform surface to the entire satisfaction of Engr-in-Charge complete all as specified and directed. Note:-(Before applying of wall care putty, Complete removing of treatment as directed and approved by Engr-in-Charge)

Applying two coats of white washing on ceiling including preparation of new/old plastered surfaces complete all as specified and directed.

Two coats of oil bound distemper on walls including preparation on new/old surfaces over coat of primer complete all as specified and directed.

Two coats of cement cement base paint on walls including preparation on new surfaces complete all as specified and directed.

Two coats of weather proof exterior emulsion paint over a coat of primer including preparation of new plastered surfaces of any description complete all as specified and directed.

S&F water closet (Orissa pattern) including lime concrete bedding, vitreous china long pan orissa pattern 580mm x 440mm, white with integral foot rests (excluding flushing cistern & flush pipe) fixed in repairs complete all as specified and directed.

Supply only cast iron 'P' trap 100mm dia complete all as specified and directed.

10 ltr capacity PVC valveless, syphonic action type flushing cistern low level white with inlet, ball valve, float and handle including connetion to pipe but fixed in repair complete all as specified. Make : Cera Model Combiflush twin flush CAT part No 2603

Supply only flush pipe of PVC 32 mm dia for low level cistern complete all as specified and directed.

Stainless steel grating doom 75mm/100mm square/round complete all as specified and directed.

Tubular towel rail, 20mm dia, D type, 60cm long between flanges aluminium anodized, fixed with rawl plugs complete all as specified and directed.

PVC connection 15mm size with PTMT nuts of lengh 450mm complete all as specified and directed.

C P brass magic eye as approved by GE in main door complete all as specified and directed.

S&F steel peg set colour coated of six as approved by GE complete all as specified and directed.

Sinks made of stainless steel 1mm thick kitchen or laboratory with plugs, washers and wastes, including bedding in cement mortar including fixing cantilever brackets connecting union to pipe and 32 mm dia GI pipe duly painted upto Nihani Trap or Floor trap complete as directed at site, overall size 495mm x 420mm bowl size 410mm x 330mm x 160mm complete all as specified and directed.

Plate rack made of stainless steel 600mm x 750mm x 0.55mm including fixing as per manufacturers instruction complete all as specified and directed.

PCC 1: 3 : 6 type C-2 (using 40 mm graded crushed stone aggregate) in surafce channel and drains complete all as specified and directed.

PCC 1: 5 : 10 type E-2 (using 40 mm graded crushed stone aggregate) as in filling under sunken floors etc complete all as specified and directed.

Dismantling cast iron pipe & reinforced concrete drain pipes, jointed in cement mortar of any dia upto 100mm complete all as specified and directed.

Cast iron soil, waste and vent pipes (sand cast) 100mm bore in any length with or without ears with cement joints laid in trenches complete all as specified and directed.

All as per srl item No 88 above but 75mm bore pipes complete all as specified and directed.

Cast iron soil, waste and vent pipes (sand cast) 100mm bore in any length with or without ears with cement joints fixed to walls duly applying a coat of bituminuous black paint complete all as specified and directed.

All as per srl item No 90 above but 75mm bore pipes fixed to wall complete all as specified and directed.

All as per srl item No 90 above but 50mm bore pipes fixed to wall complete all as specified and directed.

Fixing only 100mm dia CI soil waste and vent pipe in any length with or without ears with cement joints fixed on walls complete all as specified and directed.

All as per srl item No 93 above but 75mm bore pipes fixed to wall complete all as specified and directed.

All as per srl item No 93 above but 50mm bore pipes fixed to wall complete all as specified and directed.

Cast iron bend (any radius) diminishing pieces or tapers 100mm bore fitted with oval access door complete all as specified and directed.

Cast iron bend (any radius) diminishing pieces or tapers 75mm bore fitted with oval access door complete all as specified and directed.

Stack clamps made out of 50mm x 5mm flat iron and 16mm dia round iron stays, including bolts and nuts and securing ends of stays to wall or roof for 100/110mm bore pipe complete all as specified and directed.

Stack clamps made out of 50mm x 5mm flat iron and 16mm dia round iron stays, including bolts and nuts and securing ends of stays to wall or roof for 75 mm bore complete all as specified and directed.

Cast iron branch pieces single (equal or unequal ordinary or inverted (Spigot or socketed type) or with parallel branches 75mm bore (fixed in repairs) complete all as specified and directed.

Cast iron branch pieces single (equal or unequal ordinary or inverted (Spigot or socketed type) or with parallel branches 100mm bore (fixed in repairs) complete all as specified and directed.

PVC (SWR) pipes 110mm bore single socketed , in any length with rubber ring joints fixed to wall complete all as specified and directed.

PVC (SWR) bend any radius for 110mm bore pipe and access door complete all as specified and directed.

Cast iron vent cowl for 75m dia pipe complete all as specified and directed.

Cast iron vent cowl for 50m dia pipe complete all as specified and directed.

Cast iron floor trap 75 mm, with grating including jointing to waste pipe complete all as specified and directed.

Cast iron work in lids for oval access doors for 75mm bore pipes and fittings including all necessary threading and nut/bolt required complete all as specified and directed.

Cast iron work in lids for oval access doors for 100mm bore pipes and fittings including all necessary threading and nut/bolt required as complete all as specified and directed.

Dismantling Asbestos cement (corrugated or semi corrugated) sheets as in roof covering complete all as specified and directed.

Pre-painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50 mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall fixed with self tapping screws complete all as specified and directed.

MS flat iron as in wind ties etc confirming to Fe 410-0 or Fe 310-0 including clamps complete all as specified and directed.

Dismantling timber scantlings 40 sq. cm and over in section, in any position and in un-framed work complete all as specified and directed.

Rolled section as in main and cross beams, purlins, rafters, posts where connected to common rafter and running rails,eves board framing work, tank staging work etc conforming to Fe- 410-W (Gde E-250) quality B complete all as specified and directed.

Taking up or down steel tubing 15mm bore with connections for cleaning for refixing or removing to store yard ccomplete all as specified and directed of the following description.

Taking up or down steel tubing 20mm bore with connections for cleaning for refixing or removing to store yard complete all as specified and directed of the following description.

15mm bore galvanised steel water tubing medium grade (ISI Marked) with all fittings and fixed complete to walls and or laid under floors etc complete all as specified and directed.

20mm bore galvanised steel water tubing medium grade (ISI Marked) with all fittings and fixed complete to walls and or laid under floors etc complete all as specified and directed.

Gun metal globe of gate valve with iron wheel head, screwed both ends of size 20mm complete all as specified and directed.

Gun metal globe of gate valve with iron wheel head, screwed both ends of size 15mm complete all as specified and directed.

Fancy type chromium plated stop valve cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions chromium plated of size 15 mm complete all as specified and directed.

All as srl item No 120 but fancy type, chromium plated with long shank and cup (concealed type) complete all as specified and directed.

Bib tap cast copper alloy with crutch or butter fly handle, screwed down, screwed for iron pipe of size 15mm bore chromium plated complete all as specified and directed.

Ball Brass Valve high pressure with polythene coat and fly nut complete screwed for Iron pipe or brass ferrule and fixed of size 20mm bore complete all as specified and directed.

Brass chromium plated shower rose 125mm size with swivel joint fixed to pipe or union of 15mm bore fixed in repair complete all as specified and directed.

Dismantling water tanks and removing to store exc 250 & n.exc 500 ltrs of capacity complete all as specified and directed.

Rotational moulded polyethylene water storage tanks ( cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part-I of capacity 1000 liters including all accessories complete all as specified and directed.

Surface excavation n exc 30 cm deep and averaging 15 cm deep and getting out in hard and dense soil complete all as specified and directed.

75 mm thick PCC 1:4:8, type D-2 (by using 40 mm graded crushed stone aggregate) as in sub base floor complete all as specified and directed.

Sand cushioning 20 to 30 mm thick for laying and fixing interlocking tiles complete all as specified and directed.

Machine pressed precast concrete interlocking paver block (glossy finish) any shape and size (sample approved by GE) confirming to IS 15658-2006 of 60 mm thickness M-35 grade with grey cement and pigment complete all as specified and directed and directed.

Removing excavated soil to a distance exc 50m and n.exc 1.50 km out side defence land complete all as specified and directed.

Machine pressed (factory made) precast plain cement concrete 1:2:4 type B-1(using 20mm graded crushed stone aggregate), kerb stone & the like of size 300mm x 300mm x 100mm thick or of size as approved by GE, with plain fair faces including chamfers, weathering etc, embedding in position/laid in trenches on edges of roads, including excavation in any type of soil, setting in cement mortar (1:4) returning filling and removal of surplus soil/debris to a distance n.exc. 50m from the starting point complete all as specified and directed.

Dismantling old abandoned existing manholes any depth with debris and removing making good to earth complete all as specified and directed.

Use and waste of form work to soffits of suspended slab such as roof slab, floor slab, landing and similar work not exceeding 200mm thick surface horizontal or sloping, fair finished surface of concrete complete all as specified and directed.

Mild steel steel TMT bars 6mm to 8mm dia and over cut to length bent to shape required, including cranking, bending spirally for hooping columns hooking ends and binding with mild steel wire annealed not less than 0.9 mm dia complete all as specified and directed.

Framed work as in frames to manhole covers of angle or other section including hold fast conforming Fe-410-O complete all as specified and directed.

Precast RCC 1:2:4 type B1 (using 20mm graded crushed stone aggregates) for precast cement concrete slabs as in manhole covers set in cement mortar 1:4 complete all as specified and directed.

Brick work with sub class 'B' bricks exc 6m mean radius straight or curved on plan built in cement mortar 1:4 complete all as specified and directed.

PCC (1:2:4) type B-1 (using 20 mm graded cushed stone aggregates) as in coping, benching and the like including form work complete all as specified and directed.

Cleaning of manholes n.exc 1.50m deep and removing sludge/waste materials etc. to a distance n.exc. 1.5m and burring in pits including fillling pits with earth complete all as specified and directed.

Cleaning of gully traps of any size and burrying in pits the waste materials after removing upto 50mtrs complete all as specified and directed.

Cleaning of drain pipes 150mm bore by rodding from manhole to manhole or manhole to septic tank or vice versa and well flushing with water after cleaning, the rates include for taking off manhole covers and replacing, removing the sluldge and burrying in pits at a distance not exc. 50m complete all as specified and directed.

Cleaning of drain pipes 100mm bore by rodding from manhole to manhole or manhole to septic tank or vice versa and well flushing with water after cleaning, the rates include for taking off manhole covers and replacing, removing the sluldge and burrying in pits at a distance not exc. 50m complete all as specified and directed.

Excavation in trenches n.exc 1.5m wide and n. exc. 1.5m depth in any type of soil for foundation etc or for shafts, well drain pipes getting out in any type of soil complete all as specified and directed.

Returning fillling in including spreading, levelling watering and well ramming in layers not exc 25cm thick in each layer complete all as specified and directed.

Demolition & breaking up drain pipes (SGSW) of 100/150mm dia pipe complete all as specified and directed.

Plain cement concrete 1:4:8 type D-2 (using 40mm graded crushed stone aggregates) as in foundation filling and mass concrete complete all as specified and directed.

Plain cement concrete 1:4:8 type D-2 (using 40mm graded crushed stone aggregates) as in concrete bed to drain pipes including packing under and haunching against the sides of pipes after they are laid and tested for 100mm bore pipes complete all as specified and directed.

100mm bore salt glazed stone ware drain pipes laid in trenches and jointed complete all as specified and directed.

Plain cement concrete 1:4:8 type D-2 (using 40mm graded crushed stone aggregates) as in conc bed to drain pipes including packing under and haunching against the sides of pipes after they are laid and tested for 150mm bore pipes complete all as specified and directed.

150mm bore salt glazed stone ware drain pipes laid in trenches and jointed complete all as specified and directed.

Extra for forming fair finished drain or channel 30cm inner girth in cement concrete ,using extra cement, including forms moulds ,mitered/stopped ends etc complete all as specified and directed.

PCC 1:3:6 type C-1 as in surface channels/drains complete all as specified and directed.

Demolition of brick work or stone masonry built in cement mortar including all quoins arches, pillar etc but excluding ashlar facing , dressed stone work and precast concrete articles complete all as specified and directed.

Demucking of filled soil in drains of any size depth or section in any condition as per site requirement and complete all as specified and directed.

Removal of excavated soil to a distance n exc 50 m and spreading along road side berms complete all as specified and directed.

Brick work with sub class "B" bricks straight or curved on plan exceeding 6 m mean radius in cement mortar 1:6 complete all as specified and directed.

All as srl item No 157, but except bricks complete all as specified and directed.

15 mm thick rendering on fair faces of brick, stone or concrete surfaces ,finished even and smooth w/o using extra cement CM 1:4 complete all as specified and directed.

Reinforced cement concrete 1:2:4 type B-1 as in slab supported on walls, beams and columns, in floors, roofs, and shelves and the like complete all as specified and directed.

Form work to edges of concrete flats, bricks, concrete railing n.exc 200mm wide finished rough thick complete all as specified and directed.

PCC (1:2:4) type B-1 (using 20 mm graded crushed stone aggregate) as in coping, benching and the like including form work complete all as specified and directed.

Raised pointing to random rubble stone masonary in CM 1:3 complete all as specified and directed.

PCC (1:5:10) type E-2 (using 40 mm graded cushed stone aggregate) as in surface channels and drain beds complete all as specified and directed.

110mm bore PVC (SWR) pipe single socketed cut to size required as in weep holes complete all as specified and directed.

Excavation in post holes (or similar holes) in hard/dense soil each not exceeding 0.50 cum getting out, returning filling in and ramming earth of broken rubble mixed with earth around in layers not exceeding 25 cm complete all as specified and directed.

Plain cement concrete 1:2:4 type B-2 (using 40mm graded crushed stone aggregates) as in foundation filling and mass concrete complete all as specified and directed.

False ceiling with 12mm thick glass fibre reinforced Gypsum ceiling tiles of sixe 595mm x 595mm, prima fine fissured micro look white coloured using Aluminium powder coated "T" section 25m x 12m grid and 6mm dia GI suspension wire etc complete all as specified and directed.

Two coats of synthetic enamel paint over a coat of red oxide primer on steel surfaces complete all as specified and directed.

Pre-painted galvatume aluminum zinc coating GI based plain steel sheet 0.50 mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall , eves/facia board work fixed with self tapping screws complete all as specified and directed.

Glazed ceramic tiles in vertical surface 350 x 250 x 7 mm/ 450 x 350 x 7 mm thick set and jointed in neat cement slurry and pointed in white colour cement to match over and including 15mm thick screed bed cement mortar in 1:4 complete all as specified and directed.

Granite work 18 mm to 20 mm thick table rubbled and polished in cooking platform or similar work and line in CM 1:4 and pointing in CM 1:2 using marble dust with admixture of pigment to match the shade of granite including providing 20mm dia 02 hole for gas pipe complete all as specified and directed.

S &F in repair sinks with drainage board made of stainless steel 01 mm thick kitchen with plugs, washers and waste pipes including beeding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 915 mm x 460 mm bowl size 410 mm x 330 mm x 160 mm complete all as specified and directed.

Powder coated aluminium windows in double track both portion sliding glass of standard aluminium section fully glazed with 5.5mm thick tinted glass with openable/fixed shutters complete all as specified and directed. (a) Aluminium anodised (25 micron) frame 101 x 44.45mm x 1.95mm and aluminium anodised shtter of size 44.45 mm x 44.45 mm x 1.95 mm shulter of Jindal/Hindalco section respectively. (b) Aluminium anodised butt hinges 04 Nos in each window of 75mm size ISI marked. (c) Aluminium andodised tower bolt 03 Nos in each window 150mm long Make - Classic/Argent or ISI Marked. (d) Aluminium anodised handle 02 Nos in each plank 100 mm size Make - Classic/Argent or ISI Marked (e) Tinted glass 5.5mm thick Make - Modi/Atul

Removing excavated soil to a distance n exc 50m and depositing at alevel n exc 1.5m above the starting point complete all as specified and as directed.

20 mm bore Ball valves, high pressure with polythene float and fly nuts complete screwed for iron pipe or brass ferrule "fixed in repair" complete all as specified and directed.

12mm thick toughened glass partition including sliding shutters with all stainless steel patch fittings, brackets, rollers end beadings etc complete all as per manufactures instructions and as directed.

Precast RCC 1:2:4 type B-1 (using 20mm graded crushed stone aggregates) as in cover slabs,shelves and similar articles with plain faces etc complete all as specified and directed.

M & L for mild steel re-inforcement 10 mm dia and over cut to length bent to shape required including bending and binding complete all as specified and directed.

Use and waste of form work to soffits of suspended slab such as roof slab, floor sloping, fair finished surfaces of concrete complete all as specified and directed.

Rotational moulded polyethylene water storage tanks 500 ltr capacity hoisted and fixed complete all as specified and directed.

Medium grade galvanised steel water tubing of 15mm dia with all fittings fixed to wall complete all as specified and directed.

Medium grade galvanised steel water tubing of 20mm dia with all fittings fixed to wall complete all as specified and directed.

100mm thick PCC 1:4:8 type D-2 as in sub base of floor complete all as specified and directed.

Cement concrete 75mm thick 1:3:6 type C-2 (using 20mm graded crushed stone aggregates) as in plinth protection complete all as specified and directed.

S & F in repair steel rolling shutters of thickness 1mm with ball bearing for rolling as specified including top cover, anchoring rod, hasps and staple and one shop coat of primer errected in position as indicated complete push pull or manual type complete all as specified and directed.

Machine cut kota stone slab flooring 20-25 mm thick over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and directed.

Brass CP mixture for mixing hot & cold water screwed down for iron pipe 15mm tomy type complete all as specified and directed.

CP bib Tap 15mm cast copper alloy with crutch or butterfly handle screwed down for iron pipe or for brass ferrule complete all as specified and directed.

CI (SWR) bends 110 mm dia complete all as specified and directed.

Dismantling floor hearth or wall tiling including cement mortar bedding but not backing complete all as specified and directed.

25 mm thick PCC 1:2:4 type B-1 (using 20 mm graded crushed stone aggregate) as in sub base finished fair for receiving floor finishes complete all as specified and directed.

10 mm thick backing coat on vertical surfaces such as skirting/dado in CM 1:4 for laying tiles complete all as specified and directed.

Glazed ceramic coloured tiles 600mm x 300mm x 7mm thick in vertical surface set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified and directed.

Rendering 10mm thick on fair faces of brick/ concrete surface in cement mortar 1:3 and finished even and fair for receiving tiles on vertical surface complete all as specified and directed.

Double charge vitrified ceramic tiles, area of each tile exc 0.18 sqm but n. exc 0.36 Sqm, 10mm thick (square or rectangular) of superior quality as in floor and walls surfaces set and jointed in neat cement slurry and pointed in white or coloured cement to match the dark shade of tiles complete all as specified and directed.

Rendering 5 mm thick in CM 1:3 on ceiling and exposed surface of concrete finsihed even and smooth without using extra cement complete all as specified and directed.

Applying two coat of oil bound distempers over one coat of primer and two coat of wall care putty on new plaster surface of walls complete all as specified and directed.

Preparation of new plaster/old surfaces of wall and applying two coats of weather proof exterior emulsion paint (APEX or equivalent) over a two coat of wall care putty with coat of primer up to G+1 floor height etc complete all as specified and directed.

Preparation of new ceiling surface and applying two coat of oil bound distemper over a coat of wall care putty with one coat of primer complete all as specified and directed.

Complete removal of existing treatment of wall surface and applying two coat of plastic emulsion paint (shade to be approved by GE) over two coat of wall care putty complete all as specified and directed.

Preparation of new plastered or un-plastered surfaces and walls including cornices, pillasters etc and applying two Coats of cement base paint over a coat of primer complete all as specified and directed.

Complete removal of existing treatment and applying two coats of oil bound distemper over a coat primer with two coat of wall care putty complete all as specified and directed.

Complete removal of existing treatment and applying two coat of cement base paint over a coat of primer paint on walls complete all as specified and directed.

First class hard wood plain solid straight chowkats and frames design doors Pannel shutter with wrought framed on the solid rounded, Plemet box , partition shutter big size or chambered put together with glue and pinned at joints including preservative treatment complete all as specified and directed.

Material and labour for 10-12 mm thick toughened glass partition and similar work with fixing of stain less steel clit/stain less steel clamp and fixing door frame wall complete all as specified and directed.

18/19mm thick plywood, grade 1 (with BWR resistance/termite proof) with screws to timber frame work as in cup boards/cabinets etc complete all as specified and directed.

12mm thick plywood, grade 1 (with BWR resistance/termite proof) with screws to timber frame work as in cup boards/cabinets etc complete all as specified and directed.

0.9mm thick decorative choice of lamination type-1 or surface finish white stuck with imported adhesive on sides of board complete all as specified and directed. Make : Corby/ Euro

Reinforced cement concrete 1:2:4 type B-1 (using 20 mm graded crushed stone aggregate) as in slab supported on walls, beams and columns, drain cover slab in floors,roofs, and shelves and the like complete all as specified and directed.

Mild steel TMT bars 10mm dia and over cut to length bent to shape reqd including cranking bending spirally for hooping for columns hooking ends and binding with MS wire annealed not less than 0.9mm dia complete all as specified and directed.

Glass shelf 600 mm long with holding brackets complete all as specified and directed. Make - Jaquar Cat Part No: CAN 1171N

Corner glass shelf with chromium plated rails including brackets complete all as specified and directed. Make -Jaquar Cat Part No: CAN 1173

M&L for cutting chases in brick wall, pinning in ,making good to facing where required and pointing in cement mortar 1:3 to ends or edges of landing, steps, cills, sun shades, shelves, lintels etc.;and cutting chases for concealed water tubing or concealed conduit wiring, etc. and making good, cutting not exceeding10cm girth complete all as specified and directed.

PVC connection 15mm dia and 45cm long with two Nos of PTMT check nuts and washers complete all as specified and directed.

Dismantling of PVC Pipes of dia 75/110 mm complete all as specified and directed.

110 mm PVC (SWR) couplers for PVC pipe and similar work complete all as specified and directed.

Taking up or down of 15 mm bore pipes steel tubing and connections complete all as specified and directed.

S & F steel tubing galvanized, medium grade with all fittings, laid in floors or fixed to walls, 15mm bore complete all as specified and as directed.

Looking Mirror 5.5 mm thick of Make :- Modiguard' or 'Ashashi' mounted on 5 mm thick PVC Sheet including power coated aluminium beadinng or stainless steel stud fixing to wall of approved pattern complete all as specified and directed.

Bib taps with wall flange chromium plated complete all as specified and directed. (Make Jaquar Cat Part No : VGP ACR -81037)

Angular stop cock with wall flange complete all as specified and directed. Make Jaquar Cat Part No : FLR 5053N OR FUS -29053

Towel Ring square with round flange complete all as specified and directed. Make - Jaquar Cat Part No : ACN-1121N

Soap dish holder including all fittings complete all as specified and directed. Make - Jaquar Cat Part No: CAN 1131N

Tumbler holder chromium plated with holder and bracket complete all as specified and directed. Make - Jaquar Cat Part No: 1141N

Hand shower (Health faucet) with 8 mm dia, 1 m long flexible tube and wall hook complete all as specified and directed. Make - Jaquar Cat Part No : ALD-573

Toilet paper holder complete all as specified and directed. Make - Jaquar Cat Part No : CAN 1155N

Towel rack 600 mm long with out lower hangers but with three hooks complete all as specified and directed. Make - Jaquar Cat Part No: CAN 1181FHS

Double arm wall mounted reversible plain / magnifying (X3) pivotal mirror complete all as specified and directed. Make - Jaquar Cat Part No: ACN 1193N

Swivel mirror complete all as specified and directed. Make -Jaquar Cat Part No: ACN 1195N

Table Top basin Fusion model with pillar cock hot and cold single lever tall body with 150 mm extension body fixed spout without popup waste system with 600 long braided hoses complete all as specified and directed. Make:-Jaquar Cat Part No : FUS 29005 & FSS-WHT-29901

Self closing angle cock pressmatic for urinal with flange and 200 mm connecting pipe and spreader complete all as specified and directed. Make - Jaquar Cat Part No : PRS 077

PVC connection 15mm bore 450 mm long braided Hose with M10 x 1 Nipple, 15 mm Nut, O-Ring & Rubber washer (Suitable for Basin Mixers) complete all as specified and directed. Make: -Jaquar Cat Part No : ALD-803AB

PVC connection 15mm bore 450 mm long braided Hose with two 15 mm Nut & Rubber washer without nipple Make: Jaquar Cat Part No - ALD-805B complete all as specified and directed.

PVC waste pipe 32mm bore with cup and washers complete all as specified and directed.

Chromium plated 32 mm bore size full threaded with 80 mm height including all necessry washers complete all as specified and directed.

Hand drayer smart flow complete all as specified and directed. Make - Jaquar Cat Part No : HDR-WHT -M04A Or HDR-SAP-M99ACS

Urinal with sensor with fising accessories set Size 480x300x740mm complete all as specified and directed. Make :- Jaquar Cat Part No : URS -WHT -13255 Or Urinal Flat Back with senser integrated EFS 360 x 330 x 740 mmCera Cat No: S4010101

Cutting holes in brick wall exc half brick but n.exc one brick built in cement mortar or cement lime mortar and stone wall built in lime mortar and making good with dismantled portion in CM 1:3 or cement concrete 1:2:4 type B-0 complete all as specified and directed.

Collapsible steel gate, top hung, consisting of channel pickets, pivoted flat bars, top and bottom runners brass handles etc as specified, erected in position and securing runners with holdfasts and brackets complete all as specified and directed.

Plain or chequered steel channels, square cut or notched ( oridinary and counter sunk) forming and including necessary welding as per site reqirement complete all as specified and directed.

Rendering 15 mm thick in CM 1:4 on brick work and finished even and smooth without using extra cement complete all as specified and directed.

Applying two coat of plastic emulsion paint (Shade to be approved by GE) over two coat of wall care putty new plaster surface of walls surface with primer complete all as specified and directed.

Vitrified tiles, area of each tile not exc 0.36sqm , 10mm thick (square or rectangular) of superior quality as in floor surfaces set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles complete all as specified and directed.

Preparation of new steel surfaces and applying two coats of synthetic enamel paint over a coat of red oxide zinc chrome primer complete all as specified and directed.

PCC 1:2:4 B-0 (using 12.50mm graded crushed stone aggregate) for coping, corner of roof and similar work complete all as specified and directed.

Anodised aluminium snap grid frame work for false ceiling complete all as specified and directed.

4 mm thick non asbestos fibre cement designer building boards fixed or laid/inserted to timber/GI/aluminium frame work wih screws complete all as specified and as directed.

Centre hole basin/sink mixer with round spout with 450mm long copper pipes and brass nuts without popup, fixed in repairs complete all as specified and as directed.

Supply and fixing glass shelf corner/front with chromium plated guard rails, fixed in repairs complete all as specified and as directed.

Soap dish holder fixed in repairs including all fittings complete all as specified and directed.

S&F in replacement of Sub main wiring with two single core PVC insulated with copper conductor cable stranded of size 6 Sqmm in PVC concealed conduit 25mm dia including PVC insulated copper conductor cable 6 Sqmm as earth lead complete all as specified and as directed. Including taking down old sub main wire. Make: Gloster/ Finolex/ Polycab.

Earthing complete with galvanised steel earth plate electode 600mm x 600mm x 6.00mm thick burried directly in ground (earth pit not less than 2.25 meter deep below normal ground level connected to and including galvanised steel earth lead wire 4 mm dia by means of bolts, nuts, chock, nuts and washers of galvanised iron or steel including PCC Pit in 1:2:4 type B-I angle iron frame with RCC cover and handle, excavation and earth work in any type of soil medium grade GI watering pipe 20mm bore with funnel and wire mash and light grade GI protection pipe 15mm bore upto main board complete all as shown in electrical plate No 3 of MES Sch 2009 (Part I) connected to main control board as specified and testing completion complete all as specified and as directed.

Taking down carefully, copper/ aluminum point wiring (light, fan, socket or power) complete including fitting such as switch, sockets, ceiling rose, pendants socket,fan regulators any type, rectangular board ,light fittings,terminal boxes etc removing materials for taking credit and making good disturbed surfaces of walls floors and ceiling complete all as specified and directed.

Taking down carefully copper/aluminium sub main wiring of size 2.5/4/6 sqmm from surface/concealed at any height and removing the materials from site and making good the disturbed surfaces of walls,floors roofs etc complete all as specified and directed.

Taking down Old/ Unserviceable MCB DBs TPN / Main Switches by disconnection of electric connection including old unserviceable MCCBs, MCBs, isolators etc and making good to distrubed surface complete all as specified and directed.

Disconnecting and taking down un serviceable light fittings of any description/ capacity complete all as specified and directed.

Point wiring for one light/ fan/bell point controlled by one switch using 1.5 Sq mm FRLS copper conductor cables (multistanded) PVC insulated and unseathed in and including PVC concealed conduit as per site requirement (thickness not less than 1.5mm and 20mm dia), medium grade with Modular sunken boxes & PVC back plate for mounting modular type switches, sockets & regulators etc with front plate modular type including supplying and laying PVC insulated unsheathed 1100 volts coppper conductor cable 1.5 Sq mm as earth wire stranded and conected to earth dolly as specified.Note:- Cutting and making same the wall patchs after laying the wire and conduit using putty, white wash and distamper. The surface should be made smooth using putty and should match exactly with the existing wall finish complete all as specified and directed.

All as per srl item No 258 but for 3 pin 6 Amps socket outlet independent board including PVC insulated PVC unsheathed 1.5 sq mm earth wire and connected to earth dolly complete all as specified and directed.

All as per srl item No 258, but for 3 pin 6 Amps socket outlet on the same board including PVC insulated PVC unsheathed 1.5 sq mm earth wire and connected to earth dolly complete all as specified and directed.

All as per Srl item No 258 but for 3 Pin 16 Amps socket outlet independent board with cable 2.5 Sq mm including copper PVC insulated PVC unsheathed 1.5 sq mm earth wire standard and connected to earth dolly complete all as specified and directed.

All as per srl item No 258 but for One light point controlled by two 2-way switches with cables 1.5 sqmm size complete all as specified and directed.

All as per srl item No 258 but for 05 amp socket outlets point controlled by one switch on Independent board complete all as specified and directed.

All as per srl item No 258 but for 05 amp socket outlets point controlled by one switch on Same board complete all as specified and directed. Make- Havells or equivalent make in polycab/finolex

All as per srl item No 258 but for 3 pin 20 A socket outlet point controlled by one modular switch 20A on the independent Board with 2.5 sqmm size of copper cable as main and 2.5sqmm copper cable as earth lead complete all as specified and directed.

All as per srl item No 258 but for 3 pin 6 Amps socket outlet independent including copper PVC insulated PVC unsheathed 1.5 sq mm earth wire and connected to earth dolly complete all as specified and directed.

All as per Srl item No 258 but for 3 Pin 16 Amps socket outlet independent board with cable 2.5 Sq mm including copper PVC insulated PVC unsheathed 1.5 sq mm earth wire standard and connected to earth dolly complete all as specified and directed.

Modular switch 10 Amps single pole two way 230 V, 50 Hz, AC , with inner and outer cover strip required module complete all as specified and directed.

Modular switch 6 Amps single pole one way 230 V, 50 Hz, AC , with inner and outer cover strip required module complete all as specified and directed.

Modular switch 16 Amps single pole one way 230 V, 50 Hz, AC , with inner and outer cover strip required module complete all as specified and directed.

Modular Bell push flush type 6 amp 230 V, 50 Hz, AC , with inner and outer cover strip required module complete all as specified and directed.

Modular socket 3 Pin 6 Amps flush type 230 V, 50 Hz, AC , with inner and outer cover strip required module complete all as specified and directed.

Modular socket combined 2-in-1, 6 Pin 6 & 16 Amps 230 V, 50 Hz, AC , flush type with inner and outer cover strip required module complete all as specified and directed.

Electronic stepped type fan regulator 120 watt 230 volts 50Hz two module C/S delux type complete all as specified and directed.

Ceiling rose, surface bakelite 65mm x 50mm two to three terminals fixed on PVC Round Block complete all as specified and directed.

Calling Bell ding dong 230 volts single pole 50Hz complete all as specified and directed.

Sheet metal enclosure double door type for MCCB TPN DB upto 125 Amps, 4 way vertical type 415 volts with 400 Amps rated bus bar and neutral link including MCCB 125 Amps 16 KA , chases wall for fixing DB and making good distributed wall surfaces to match with existing specification complete all as specified and directed.

Sheet metal enclosure double door type for DBs (when MCB to be used) 12 way 240 volts with 200 Amps rated bus bar and neutral link including chases wall for fixing DB and making good distributed wall surfaces to match with existing specification complete all as specified and directed.

S & F in replacement MCCB Triple Pole & Neutral capacity of 100 amps 415 volts rupturing capacity 16 KA complete all as specified and directed.

S & F in replacement MCB Single pole and neutral 240 volt any rating from 40 Amps"C" series, with rupturing capacity 10 KA ,inculding providing thimble for out going cable complete all as specified and directed.

S & F in replacement MCB single pole 240 Volt any rating from 10 to 40 Amps "C" series, with rupturing capacity 10 KA ,inculding providing thimble for out going cable complete all as specified and directed.

S & F in replacement MCB single pole and neutral 240 volt any rating from 63 Amps "C" series, with rupturing capacity 10 KA inculding providing thimble for out going cable complete all as specified and directed.

Sub main wiring with two single core PVC insulated with copper conductor cable stranded of size 10 Sqmm in PVC concealed conduit 25mm dia including PVC insulated copper conductor cable 6 Sq mm as earth lead all as specified. Including taking down old sub main wire complete all as specified and directed.

Sub main wiring with two single core PVC insulated with copper conductor cable stranded of size 6 Sqmm in PVC concealed conduit 25mm dia including PVC insulated copper conductor cable 6 Sq mm as earth lead all as specified. Including taking down old sub main wire complete all as specified and directed.

Sub main wiring with two single core PVC insulated with copper conductor cable stranded of size 4 Sqmm in PVC concealed conduit 25mm dia including PVC insulated copper conductor cable 4 Sq mm as earth lead all as specified. Including taking down old sub main wire complete all as specified and directed.

Material and labour for GI strip 25mm x 3.15mm with saddles and fixing screws etc. for roof conductors and down conductors above ground complete all as specified and directed.

Taking down ceiling fan/Exhaust fans (C/F of any size/make), cleaning its dust particles oiling,greasing,one coat of synthetic enamel white spray painting with blade ,reassemble the same along with all fittings and hanging the same back to its original position including connecting the wire to ceiling rose etc complete after completing the wiring all as specified and as directed. Note :- (i) The spares like condensor, ball bearing, cotter pin, nuts & bolts, connecting rods & hooks etc if found defective/damage deemed to be replaced and make the ceiling fans functional. No extra payments will be done on this account.

Angular Lamp holder, PVC/Polycarbonate type with cord grip cap suitable for light fittings complete all as specified and directed.

Supply and fixing LED Bulb 15W, 230V,AC suitable for Angular Lamp holder complete all as specified and directed.

Supply and fixing LED lights fitting 1x 22W, 230V, AC decorative box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete all as specified and directed.

LED light fitting 1 x 9W/1 x 10W bulk head luminaires including LED light driver holder connecting up with three core flexible copper conductor cable of suitable size complete all as specified and directed.

Supply and fixing LED light fitting mirror type with high out put diffuser 2 feet, 10 watt 220 V AC decorative type with driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size complete all as specified and directed.

Supply and fixing LED building security light fitting 35 Watt 230 V AC outdoor type with high pressure die cast aluminum hosing and heat resistant complete with driver, lamp,clamps,suitable bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 65/66 protection complete all as specified and directed.

Street light Bracket complete made of GI pipe of suitable size, medium grade 1.2 m long bent to shape as per site requirement along with MS flat iron clamps with nuts, bolts, washers including grouting the same with wall complete all as specified and directed.

Material & Laying in trenches or passing through pipe, 1100 volts grade heavy duty cable with "XLPE" insulated aluminium conductor standard served with an inner sheathing of PVC tape armoured with galvanised steel wire or tape and overall PVC sheathed of 25 Sqmm x 3.5 core size all as specified including taking down old cable complete all as specified and directed. Note : Earth work and other connected work shall be measured & paid sparately.

Dry sand for sand cushioning to under ground cable 8 cms thick before laying the cable before and 15 cms thick after laying & streching the cable in trenches, including hand punning and consolidating complete as specified. Note : for payment purpose punned thickness shall be measured

Bricks sub class 'B' brick laid dry, flat with width equal to length of brick as cover laid over the cabel to give mechanical protection to underground cabels complete all as specified and directed.

Supply and fixing in repairs GI tubing light grade 40 mm dia along the wall/ in trenches/ in duct / in culvert /road crossing and including provisioning of suitable mild steel flat iron clamps and bolts, nuts and double washers etc for holdining of GI pipe alongwith poles complete all as specified and directed.

Switch button single pole one way 10 Amps 240 volt ( Modular Type ) with outer strip complete all as specified and directed. ( Note- All modular cover plate/ modular flush Box/Switch/Sockets Incorporated with this, should be in same Make - Havells(crabtree)/phillips/Indoasian

Switch piano flush button single pole one way 20 amps 240 volt ( Modular Type ) with outer strip, complete all as specified & directed. Make - Havells(crabtree)/phillips/Indoasian

Sockets Combined 2-in-1, 3 pin 6 Amps, 240 Volt flush type ( Modular Type ) with outer strip complete all as specified & directed. Make - Havells(crabtree)/phillips/Indoasian

Sockets Combined 2-in-1, 3 pin 20 Amps, 240 Volt flush type ( Modular Type ) with outer strip, complete all as specified & directed. Make - Havells(crabtree)/phillips/Indoasia

Ceiling rose surface bakelite, 3 terminals complete all as specified and directed.

Supply & fixing in replacement fan regulator 120W, 230V 50 C/S, delux Modular type electronic, step type hum free suitable control speed of fan from 0 to 100 % and connecting electrically complete all as specified and as directed. Make - Havells(crabtree)/phillips/Indoaisan

Slim linear LED tube light fixture 20 Watt, with T8 polycarbonate 6500 K Housing made of extruded AL with lumen O/P should not be less than 100 lum/watt making all connection using 1.5 sqmm copper conductor multistranded PVC insulated 3 core flexible cable from ceiling rose to fitting drawn through PVC flexible conduit complete all as specified and as directed. Make- Havells Cat Part No- ( E-Lite LED Pride Plus Neo ) LHEXACP7UN1W020 Or Equivalent make in Philips/Polycab

Slim linear LED lighting fixture 5 Watt LED Batten ,For mirror light purpose , Complete making all connection using 1.5 sqmm copper conductor multistarnd PVC insulated 3 core flexible cable from ceiling rose to fitting complete all as specified and as directed. Make - Havells ( E-Lite LED Pride Plus Neo ) LHEXBTP7IN1W005 Or Equivalent make in Philips/Polycab/Cromton

Supply & fixing 10 watt LED hexagon bulk head, IP66, Environmental friendly, ultra modern, energy saving, surface mounted, complete making all connection using 1.5 sqmm copper conductor multistarnd PVC insulated 3 core flexible cable complete all as specified and as directed. Make- Havells ( Hexa 10 W ) Cat Part No-HEXAFT10WLED857SSYMBOPC or Equivalent make in Philips/Polycab

Submain wiring with two single core PVC insulated unsheathed , FRLS flexible copper conductor cable of size 10 sqmm and one single core PVC insulated unsheathed ,FRLS flexible copper conductor cable of size 6.0 sqmm as earth lead in & inculding PVC casing / non metallic rigide PVC conduit medium grade, and making good the distured complete all as specified and as directed. Make- Havells or equivalent make in polycab/finolex.

Sheet metal enclosure MCB distribution board single pole & neutral 240 volts 8 way with IP-43 IK-09 protection double door complete with appropriate size bus bar and neutral link, fixed flush in wall including chases wall for fixing DB and making good distributed wall surfaces to match with existing specification complete all as specified and directed. (Note-MCBs will be measured separately.)

S & F in replacement MCB single pole 240 volt any rating from 10 to 32 amps ,B- Series , with rupturing capacity 10 KA ,inculding providing aluminium thimble for out going cable complete all as specified and directed. Make -Schneider (Acti-9 ) / Siemens ( Betagard-8GB32 )/ Havells

S & F in replacement MCB Single Pole & Neutral 240 volt any rating from 40 to 63 Amps, B- series, with rupturing capacity 10 KA, inculding providing aluminium thimble for out going cable complete all as specified and directed. Make -Schneider (Acti-9 ) / Siemens ( Betagard-8GB32 )/Havells

Mettalic Exhaust fan 300mm sweep 240V AC single phase complete with louvers ,including provison of flexible three core copper conductor cable of 23/.0076 upto ceiling rose complete making suitable holes on wall and making proper edges by plastering/white cement/putty and match with existing surface with colour/white oil distempering for fixing the same all as specified and as directed.

Switch Piano flush type 10 Amps single pole one way (Modular Type) with outer strip complete all as specified and directed.

Socket 2-in-1, 3 Pin 6 Amps (Modular Type) with outer strip complete all as specified and directed.

Modular switch socket combined 2-in-1, 6 Pin 6 & 16 Amps 230 V, 50 Hz, AC , flush type with outer/inner cover complete all as specified and directed.

Supply and fixing electric water heater,storage type steel body with copper inner tank and heating element upto 2 KW capacity 03 litre, BEE 5 Star rated complete with all accessories such as safety valve, thermostate,NRV, connection piece etc complete all as specified and directed. Make: Jaquar/Havells/CG

vijay constrction co

M/s JAMWAL BUILDERS

RAMAN CONSTRUCTION CO