Welcome maint services including smart application and repair to internal electrification in Offrs MD Accn in Khetrapal Enclave and MAP Ph-I under AGE B/R-II at Suratgarh Mil Stn

Amount

Demolition of stone slabs and tiles of any description or thickness in floors, aprons etc, laid, bedded, jointed and pointed in any mortar complete all as specified and directed by Engineer-in-charge.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) and rubbish off the premises complete all as specified and directed by Engineer-in-charge.

Taking down eaves gutters and rain water pipes (any size or pattern), including all fittings, heads, shoes, bends, swan-necks, etc (measured overall as fixed along the centre line over fittings and accessories) complete all as specified and directed by Engineer-in-Charge.

Taking down cement plaster or cement lime plaster on stone surface/brick surfaces of walls including raking out joints hacking for key scrubbing down with water etc complete all as specified and directed by Engineer-in-charge.

S&F in repair door seal rubber strip fixed with aluminium frame at door bottom for gap 2-30mm complete all specified

S&F in repair galvanized mild steel wire cloth 0.56 mm nominal dia of wire and average width of aperture 1.18mm and fixed with tinned tacks or galvanized wire staple complete all as specified and directed by Engineer-in-charge.

S&F in repairs powder coated stainless steel drapery rod of 20 mm inner dia (in lengths as directed) of approved colour with & including decorative finial at both ends and pair of powder coated mild steel brackets fixed at both ends with PVC rawl plug & steel screws on walls/beam, including PVC curtain rings of matching colour @ 10cm C/C all as specified & as directed.

M&L for cutting or grinding surfaces of old kota stone flooring, skirting, dados etc with car boredom stone by hand or grinding machine, dusting off the surfaces after grinding and finally washing the surface clean with oxalic acid solution and polishing with bees wax polish complete all as specified and directed by Engineer-in-charge.

M&L for 16 to 18mm thick Granite (of any type) slab of approved shade as in flooring, platform etc, bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match with shade of Granite stone including cutting, grinding over & including 15mm thick screed bed (bedding layer) in CM (1:6) complete all as specified and directed by Engineer-in-charge.

M&L for non skid ceramic joint free white coloured tiles 7 to 8mm thick (square / rectangular) area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm as in floors, set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles over & including 15mm thick screed bed in cement & sand mortar (1:6) complete all as specified and directed by Engineer-in-charge.

M&L for non skid ceramic joint free coloured tiles 7 to 8mm thick (square/rectangular) area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm on vertical surfaces such as dado, skirting etc., set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles over & including 10mm thick rendering in cement & sand mortar (1:4) complete all as specified and directed by Engineer-in-charge.

M&L for glazed ceramic tiles (coloured) 450mm x 350mm x 7mm thick on vertical surfaces such as dado, skirting etc., set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles over & including 10mm thick rendering in cement & sand mortar (1:4) including necesary cutting as per site requirment complete all as specified and directed by Engineer-in-charge.

M&L for 10mm thick vitrified ceramic light shade (as approved) coloured tiles (square / rectangular), polished, area of each tile not exceeding 0.36 sqm as on vertical surfaces such as dado, skirting etc., set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles over & including 10mm thick rendering in cement & sand mortar (1:4) complete all as specified and directed by Engineer-in-charge.

M&L for 15mm thick rendering in cement mortar (1:4) on fair faced or on other than fair face surface of brick masonary or concrete surface of walls, finished even & smooth without using extra cement complete all as specified and directed by Engineer-in-charge.

M&L for 10mm thick rendering in cement mortar (1:6) on fair faced or on other than fair face surface of brick masonary or concrete surface of walls, finished even & smooth without using extra cement complete all as specified and directed by Engineer-in-charge.

M&L for 5mm thick rendering in cement mortar (1:3) on brick or concrete surface of ceiling, finished even & smooth without using extra cement complete all as specified and directed by Engineer-in-charge.

M&L for preparation of newly plastered surfaces of ceiling and applying three coats of white wash complete all as specified and directed by Engineer-in-charge.

M&L for preparation of old decorated, plastered or pointed surfaces of ceiling by brooming down or steel wire brushing,scrapping down smoke soot moulds, moss and efflorescent, salts and treating oil & greasy spots etc and applying one coat of white wash complete all as specified & directed by Engineer-in-Charge.

M&L for preparation of old decorated, plastered or pointed surfaces of wall by brooming down or steel wire brushing,scrapping down smoke soot moulds, moss and efflorescent, salts and treating oil & greasy spots etc and applying two coat of white wash complete all as specified & directed by Engineer-in-Charge.

M&L for complete removal of existing treatment of wall/roof includiing facia cornices etc by scrapping with mechanical sander with sanding pad of 80 grit having dia 7"/9" to make surface clean, free from dust, loose paint etc by skilled labour and applying two coat of distemper oil emulsion using airless spray technology with spray gun with a max hose length of 30 mtr over a coat of acrylic waterbased interior grade primer @ 0.8 ltr (undiluted)/10 sq mtrs diluted with water in 1:1 ratio to be applied with fully automatic airless spray machine of paint application over waterproof cement based ptty @ 1kg (undiluted) per sq mtr of average thickness 1 mm over the plastered/ old painted wall after scrapping to prepare the surface even and smooth complete and sanding of the putty surface with wall sander with sanding pad of 240 Grit or above to make surface free from dust. Step 1 : Mix the putty powder by adding water as per manufacturer instructions. Step 2 : Apply th first coat the prepared mixer with the help of fully automatic airless spary machine of putty application. Step 3 : Allow 6-8 hrs time to dry the putty surface. Step 4 : Allow 6-8 hrs to dry the surface for painting of subseqeunt coats.

M&L for complete removal of existing treatement from old decorated plastered surfaces of walls by scrapping with mechanical sander (having mechanical Vacuum mechanism) with sanding pad or 80 grit having dia of 7" / 9" to make surface clean, free from dust, loose paint etc by skilled labour and applying two coat water based premium acrylic smoth exterior emulsion of approved colour with silicon additive & color stay technology, Excellent dirt pick up resistance with low VOC less than 50 gram/ litre as per the LEEDS specifications, Anti Algal Properties in two coats @ 1.7 ltrs (undiluted )/10 sqm diluted with water as per manufacture instruction over one coat of acrylic water based exterior grade primer @0.9 ltr (undiluted)/10 sq mtrs diluted with water in 1:1 ratio to be applied with fully automatic airless spray machine. (i) Allow 6-8 hrs to dry the surface for painting of subsequent coats and applied over priming coat with fully automatic airless spray machine of paint application (ii) Allow 6-8 hrs to dry the surface in both the coats of paint complete all as specified and directed by Engineer-in-Charge. (iii) The Contractor shall received a guarantee certificate from manufacturer and same shall be submitted to department.

M&L preparing newly plastered surfaces of walls by scrapping with mechanical sander with sanding pad of 80 grit having dia 7"/9" to make surface clean, free from dust, loose paint etc by skilled labour and applying two coat of distemper oil emulsion using airless spray technology with spray gun with a max hose length of 30 mtr over a coat of acrylic waterbased interior grade primer @ 0.8 ltr (undiluted)/10 sq mtrs diluted with water in 1:1 ratio to be applied with fully automatic airless spray machine of paint application over waterproof cement based ptty @ 1kg (undiluted) per sq mtr of average thickness 1 mm over the plastered/ old painted wall after scrapping to prepare the surface even and smooth complete and sanding of the putty sufgace with wall sander with sanding pad of 240 Grit or above to make surface free from dust. Step :1 Mix the putty powder by adding water as per manufacturer instructions. Step: 2 Apply the first coat the prepared mixer with the help of fully automatic airless spary machine of putty application. Step: 3 Allow 6-8 hrs time to dry the putty surface. Step: 4) Allow 6-8 hrs to dry the surface for painting of subbseqeunt coats.

M&L for preparing newly plastered surfaces of walls by scrapping with mechanical sander (having mechanical Vacuum mechanism) with sanding pad or 80 grit having dia of 7" / 9" to make surface clean, free from dust, loose paint etc by skilled labour and applying two coat water based premium acrylic smoth exterior emulsion of approved colour with silicon additive & color stay technology, Excellent dirt pick up resistance with low VOC less than 50 gram/ litre as per the LEEDS specifications, Anti Algal Properties in two coats @ 1.7 ltrs (undiluted )/10 sqm diluted with water as per manufacture instruction over one coat of acrylic water based exterior grade primer @0.9 ltr (undiluted)/10 sq mtrs diluted with water in 1:1 ratio to be applied with fully automatic airless spray machine. (i) Allow 6-8 hrs to dry the sureface for painting of subsequent coats and applied over priming coat with fully automatic airless spray machine of paint application (ii) Allow 6-8 hrs to dry the surface in both the coats of paint complete all as specified and directed by Engineer-in-Charge. Note for item No 20 to 23 : (i) The Contractor shall be done above work through authorised applicator of the manufacturer. (ii) The authorised applicator shall be submitted their authorization applicator certificate of respective manufacturer to contractor and same shall be submitted by contractor to department.

M&L for preparation of old painted wooden or wood based surfaces of any description not otherwise described over 10cm width or girth and applying one coat of synthetic enamel paint complete all as specified and directed by Engineer-in-Charge.

M&L for preparation of old painted steel and iron surfaces of any description not otherwise described over 10 cm width or girth and applying one coat of synthetic enamel paint of approved tint complete all as specified and directed by Engineer-in-charge.

Hacking out old broken glass any thickness, size, quality or description from wooden / metal frame and punching or drilling out old glazing pins/spring clips complete all as specified and directed by Engineer-in-charge.

M&L for securing of old glass of any description in existing metal frame glazed with putty / beads including removing loose or decayed putty, beads painting / oiling one coat on rebates, groves reputting and painting / oiling puttied surface to match existing work (New length of frame reputtied shall be measured complete all as specified and directed by Engineer-in-charge.

S&F 3mm thick sheet glass ordinary quality and glazing with oil putty in square not exc 0.5 sqm in each pane including painting / oiling to new putty to match with the existing/new surfaces, complete all as specified and as directed.

S&F 4mm thick figured glass pin head type and glazing with oil putty in square not exc 0.5 sqm in each pane complete all as specified and directed by Engineer-in-charge.

S&F in repair 15mm bore brass chromium plated shower rose with or without swivel joints, any size, including fixing to steel pipe or union with shower arm 15mm size, 195mm long iwht bend of 45 degree with flange complete all as specified and directed by Engineer-in-charge.

S&F in replacement 600mm long PVC connection suitable for 15 mm bore with PTMT nuts on both sides complete all as specified and directed by Engineer-in-charge.

S&F in repair chromium plated towel ring round with round flange 200mm dia including chromium plated brass screws and plastic cleats complete all as specified & directed by Engineer-in-Charge. Make :- Cera cat part No COVS3010103 or equivalent cat part No of makes as mentioned in Appendix 'A'.

S&F in repair brass chromium plated tubular towel rail 20mm dia; 'D' type, 600mm long between flanges fixed to plug with chromium plated brass screws including wooden or plastic cleat complete all as specified and directed by Engineer-in-Charge. Make :- Cera cat part No F5007103 and Jaquar cat part No AEC-1133 or equivalent cat part No of makes as mentioned in Appendix 'A'.

S&F in repair hand faucet chromium plated complete all as specified and directed by Engineer-in-charge. Make :- Jaquar Code No ASIN-B014DCGOYU or equivalent cat part No of makes as mentioned in Appendix 'A'.

S&F in repair grating doom 125mm dia of PTMT with waste hole (minimum weight 40 grams) complete all as specified and directed by Engineer-in-Charge.

S&F in repair 15 mm bore bib tap, cast copper alloy chromium plated with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule complete all as specified and directed by Engineer-in-charge. Make :- Cera cat part No F2002151 and Jaquar cat part No TQT-511 or equivalent cat part No of makes as mentioned in Appendix 'A'.

S&F in repair 15 mm bore bib tap, cast copper alloy, chromium plated, long body, fancy type screwed down and screwed for iron pipe or for brass ferrule complete all as specified and directed by Engineer-in-charge. Make :- Cera cat part No F2002152 and Jaquar cat part No COS-103107 or equivalent cat part No of makes as mentioned in Appendix 'A'.

S&F in repair fancy type pillar tap, cast copper alloy with capstan heads, chromium plated, screwed down high pressure, with or without lettered ‘Hot’ or ‘Cold’ with long screwed shankS&Fly nuts, screwed suitable for iron pipes of 15mm bore complete all as specified and directed by Engineer-in-charge. Make :- Cera cat part No F1015101 and Jaquar cat part No MQT-508KN or equivalent cat part No of makes as mentioned in Appendix 'A'.

S&F in repair 15mm dia stop cock cast copper alloy, fancy type with, chromium plated long shank and cup (concealed type) with crutch or butterfly handle screwed down high pressure, screwed both ends for iron pipe complete all as specified & directed by Engineer-in-charge.

S&F in repairs 15mm bore brass chromium plated basin mixer for mixing hot & cold water screwed down for iron pipe of 15mm bore complete all as specified and directed by Engineer-in-charge.

S&F in repairs 15mm bore brass chromium plated wall mixer for mixing hot & cold water screwed down for iron pipe of 15mm bore complete all as specified and directed by Engineer-in-charge.

S&F in repairs 15mm bore brass chromium plated wall mixer with a point of shower for mixing hot & cold water screwed down for iron pipe of 15mm bore complete all as specified and directed by Engineer-in-charge.

S&F in repair 15mm bore angle valve, cast copper alloy, chromium plated, screwed down, high pressure with crutch or butterfly handle screwed both ends for iron pipe or for unions complete all as specified and directed by Engineer-in-charge. Make :- Cera cat part No QT and Jaquar cat part No TQT-526N or equivalent cat part No of makes as mentioned in Appendix 'A'.

S&F in repair toilet paper holder chromium plated complete all as specified & directed by Engineer-in-Charge.

S&F in repair vitreous china wash basin white, flat back of size 550x400mm including including a pair of cast iron brackets embedded in PCC 1:3:6 type C-1 blocks of size 10 x 7.5 x15 cm with & including 32 mm dia PVC waste pipe, 32mm dia PTMT waste coupling half or full thread (minimum wt 45 grms) flange end bedded in red lead cement & other end fixed to waste pipe and including brass chromium plated fancy type pillar tap, screwed suitable for iron pipes of 15mm bore complete all as specified and directed by Engineer-in-Charge. Make :- Cera cat part No F2013461 and Jaquar cat part No MQT-516AKN or equivalent cat part No of makes as mentioned in Appendix 'A'.

S&F in repair vitreous china squatting pan Orissa pattern, white of size 580x440mm with integral foot rests (excluding flushing cistern and flush pipe) including cast iron 'P' or 'S' trap, PCC filling and connection to trap and flushing pipe, antisyphonage pipe etc complete all as specified and directed by Engineer-in-charge.

S&F in repairs vitreous china wash down water closet pan (Pedestal pattern EWC), coloured floor mounted coupled closet of size 355mm x 665mm x 705mm, including connection to drain (or outgoing pipe), anti-sypohonage pipe etc. with & including WC seat cover closed pattern with flat bottom and cover, CP jet nozzle, vitrrous china symphonic action type twin flush flushing cistern of 10 litre capacity with lid, necessary fittings complete all as specified & as directed by Engineer-in-charge. Make :- Cera cat part No S1053102 (Snow White) or equivalent cat part No of makes as mentioned in Appendix 'A'.

S&F in repairs vitreous china wash down water closet pan (Pedestal pattern), white including connection to drain (or outgoing pipe) and to flushing pipe, anti-sypohonage pipe etc. & with plastic WC seat cover white closed pattern with flat bottom and cover and mild steel chromium plated or aluminized hinging device and jet spray complete all as specified & as directed by Engineer-in-charge.

S&F in repair 10 litre capacity PVC valveless symphonic action type low level flushing cistern (ISI marked) including 32 mm dia PVC flush pipe connected to water closet with inlet, ball valve, float and handle complete all as specified and directed by Engineer-in-charge.

S&F in repairs plastic water closet seat, white, closet pattern with flat bottom and cover and mild steel chromoum plated or aluminised hinging device complete all as specified and directed by Engineer-in-Charge.

S&F in repair Waste coupling of PTMT (half or full threaded) 32mm bore dia discharge pipe (Minimum weight 45 gms) complete all as specified and directed by Engineer-in-charge.

S&F in repair Waste coupling of PTMT (half or full threaded) 40mm bore dia discharge pipe (Minimum weight 45 gms) complete all as specified and directed by Engineer-in-charge.

S&F in repair PVC cabinet with mirror of size 450x600mm complete all as specified & directed by Engineer-in-Charge.

S&F in repairs PVC waste pipe 32 to 40mm bore suitable for WHB or Sink complete all as specified and directed by Engineer-in-charge.

S&F in repair sink with drainage board made of stainless steel 1mm thick for kitchen with plugs, washers and wastes, overall size 915mm x 460 mm / (36" x 18") bowl size 410mm x 355mm / (16" x 14") and depth 175mm / (7") including waste pipe of polythelene of low or high density or PVC 32mm dia & waste fitting brass chromium plated 32mm bore with long screwed shanks and fly nuts including making holes in brick walls for brackets and fixed in CM (1:3) or PCC 1:2:4 type B0 complete all as specified and directed by Engineer-in-charge. Make :- Nirali model Elegance (Glossy) / Prayag model No 1128-D Gold Series (Gloss) / Silver Shine (Bluestar sanitary industries Pvt Ltd) model No SSSB-52 (Glossy) or equivalent cat part No of makes as mentioned in Appendix 'A'. Note :- Size of sink for different mafufacturer may slightly varried from size mentioned in description of item. Contractor has to provide sink as per cat No mentioned against make of sink. where cat No is not mentioned against any make, in that case sink of size mentioned in description has to provide, if exact size of sink is not available, then next higher size sink has to be provided. Nothing extra shall be paid on this account.

S&F in repair stainless steel plate rack of size 750mm x 600mm x 254mm made out of 0.63mm thick stainless steel of first quality complete all as specified and directed by Engineer-in-Charge. Make: Silver Shine (Blue Star sanitary industries Pvt Ltd) Model No KPR 313 / Prayag model No P-340 / Blue Star (Anupam Industries) model No KPR-313 or equivalent cat part No of makes as mentioned in Appendix 'A'.

S&F in repair white or coloured PTMT shelf 450mm long fixed with and including chromium plated brass screw and plastic cleats (Minimum weight 300gms) complete all as specified and directed by Engineer-in-Charge.

S&F in repair jet spray chromium plated brass for ewc with & including PVC connection 600mm long suitable for 15mm bore GI pipe complete all as specified & directed by Engineer-in-Charge.

S&F 75mm bore PVC (SWR) pipes single socketed in any length jointed with adhesive fixed to walls fixed with and including requisite Number of clamps made out of flat iron 25x4mm complete all as specified and as directed by Engineer-in-charge.

S&F 110mm bore PVC (SWR) pipes single socketed in any length with solvent joints laid In trenches or in floors complete all as specified and directed by Engineer-in-charge.

S&F 75mm bore PVC (SWR) pipes single socketed in any length with solvent joints laid In trenches or in floors complete all as specified and directed by Engineer-in-charge.

S&F 110 mm bore PVC (SWR) bends any radius jointed with adhesive with oval access door complete all as specified and as directed by Engineer-in-charge.

S&F 75 mm bore PVC (SWR) bends any radius jointed with adhesive with oval access door complete all as specified and as directed by Engineer-in-charge.

Taking down carefully or drawing out from conduit, existing copper / aluminium point wiring for light, fan, bell, socket, power point etc complete including fixture and fittings such as switches, sockets, ceiling rose, pendent holder, light fittings, top sheet covers, fan regulators, MCB, DB, lamp, earth plug etc (excluding MS sunken boxes) and making good the disturbed surfaces of wall/ceiling complete all as specified and as directed by Engineer-in-charge. Note : Taking down of serviceable fittings shall be measured and paid separately.

M&L for Modular point wiring complete with 1.5 Sqmm (nominal cross section area) FRLSH PVC insulated multistranded unsheathed copper conductor cable drawn in and including concealed PVC rigid conduit medium grade 20mm dia, pipe hooks, elbows, junction covers and junction boxes including cutting chases in walls for conduits and for sunken pressed steel terminal boxes and making good the disturbed surfaces of wall with all jointing accessories including provision of pressed steel sunken terminal boxes made of 1.2mm thick pressed steel sheet, 60mm deep of suitable length and painted with red oxide primer for mounting modular switches, sockets, fan regulator including suitable size modular plates fixed flush with wall including 1.5 Sqmm PVC insulated multistranded unsheathed copper conductor wire as earth continuity to common earth and connecting to earth dolly for one light point, fan point, bell point controlled by one switch complete all as specified and directed by Engineer-in-Charge. Note : The quoted rate shall be deemed to included with modular cover plates with frame of any colour and metal flush boxes of suitable size as directed by Engr-in-Charge.

All as per serial item No. 66 here-in-before but for One 3 pin 5 Amp socket outlet on the same board with other switches.

All as per serial item No. 66 here-in-before but for One 3 pin 5 Amp socket outlet on independent board.

All as per serial item No. 66 here-in-before but for One light point controlled by Two 2- way switches.

All as per Srl item No. 66 above, but wiring with cable of cross sectional area 2.5 Sqmm (nominal area) multi-stranded copper conductor FRLSH, PVC sheathed cable 1100 Volts shade for one switch socket combination 6 pin, 5/15 Amps on independent board including 2.5 Sqmm PVC insulated multistranded unsheathed copper conductor wire as earth continuity to common earth dolly.

S&F Modular switch piano 6 Amps single pole, one way, 01 Module complete all as specified and directed by Engineer-in-charge.

S&F Modular switch piano 6 Amps single pole, two way, 01 Module complete all as specified and directed by Engineer-in-charge.

S&F Modular switch piano 16 Amps single pole, one way, 01 Module complete all as specified and directed by Engineer-in-charge.

S&F Modular socket 2 / 3 pin, 6 Amps, 230 volts, combined 2 Module complete all as specified and directed by Engineer-in-charge.

S&F Modular socket 6 pin, 6 / 16 Amps, 230 volts, combined 2 Module complete all as specified and directed by Engineer-in-charge.

S&F Modular bell push, flush type, 5 Amp, 230 Volts grade complete all as specified and directed by Engineer-in-charge.

S&F Modular electronic fan regulator suitable for ceiling fan 2 Module, 1200mm / 1400mm sweep, socket size, rotary type complete all as specified and directed by Engineer-in-charge.

M&L for point wiring complete with 1.5 sqmm (nominal cross sectional area) FRLSH PVC insulated multistandard unsheathed copper conductor cable with colour coding drawn in and including new PVC rigid conduit medium grade 20mm dia and suitable fittings, fixed on surface of wall or concealed or above ceiling with accessories such as pipe hooks, elbows, junction box, terminated in existing sunken box and covered with new 3mm thick bakelite plastic laminated sheet top cover fixed flush with wall using brass screws & cup washers including cutting chases in wall for conduits and making good the disturbed surfaces of wall and including 1.5 sqmm PVC insulated unshethed multistandard copper conductor wire as earth continuity to common earth and connecting to earth dolly for one light point, fan point, bell point controlled by one switch complete all as specified and directed by Engineer-in- charge.

All as per serial item No. 78 here-in-before but for One 3 pin 5 Amp socket outlet on the same board with other switches.

All as per serial item No. 78 here-in-before but for One 3 pin 5 Amp socket outlet on independent board.

All as per serial item No. 78 here-in-before but for One light point controlled by Two 2- way switches.

All as per serial item No. 78 here-in-before but for One bell or buzzer point controlled by by one push button on same board with other or independent switches

All as per Srl item No. 78 above, but wiring with cable of cross sectional area 2.5 Sqmm (nominal area) multi-stranded copper conductor FRLSH, PVC unsheathed cable 1100 Volts shade for one switch socket combination 6 pin, 5/15 Amps on independent board including 2.5 Sqmm PVC insulated multistandard unsheathed copper conductor wire as earth continuity to common earth dolly.

S&F switch socket combination 5 pin, 5/15 Amps, 230 volts, flush type complete all as specified and directed by Engineer-in-charge.

S&F socket outlet 3/5 pin, 15 Amps 240 volts, flush type complete all as specified and directed by Engineer-in-charge.

S&F switch piano flush button 5 Amps single pole, one way complete all as specified and directed by Engineer-in-charge.

S&F switch piano flush button 5 Amps single pole, two way complete all as specified and directed by Engineer-in-charge.

S&F switch socket combination 3 pin, 5 Amps, 240 volts, flush type complete all as specified and directed by Engineer-in-charge.

S&F socket outlet 3/5 pin, 5 Amps 240 volts, flush type complete all as specified and directed by Engineer-in-charge.

S&F bell push, flush type, 5 Amp, 230 Volts grade complete all as specified and directed by Engineer-in-charge.

S&F electric bell (ding - dong), AC, 230 Volts, Single pole & connecting up complete all as specified and directed by Engineer-in-charge.

S&F ceiling rose surface bakelite 65mmx50mm with two or three terminal complete all as specified and directed by Engineer-in-charge.

S&F electronic fan regulator suitable for ceiling fan 1200mm/1400mm sweep, socket size, rotary type complete all as specified and directed by Engineer-in-charge.

S&F Energy efficient decorative ultra slim, prewired, Maxoled batten for T-8 LED retro lamp, ultra bright, glass shell, glare free, wide angle single/ double side connection retrofit LED tube with G-13 lamp holder/patti 20 watt LED light fitting (Day cool light) including 20 watt LED tube with all accessories prewired fixed on wall / hanging complete all as specified and as directed by Engineer-in-charge.

S&F Energy efficient decorative ultra slim prewired 9 / 10watt (600mm length) LED light fitting (Mirror light) (Day cool light), surface and wall mounted LED batten, extruded aluminium housing with polycarbonate diffuser & integrated electronic driver and all accessories fixed on wall / hanging complete all as specified and as directed by Engineer-in-charge. Make :- Havells Cat part No LUMILINEBS9WLED865S PCWH and Crompton cat part No LCTLN-10-CDL or equivalent cat part No of makes as mentioned in Appendix 'A'.

S&F Lamp holder, insulated body with back plate etc complete all as specified and as directed by Engineer-in-Charge.

Supply and fixing LED lamp minimum 3 star rated 9W LED B-22 base complete all as specified and directed by Engr-in-Charge with following specifications (a) Lumen system efficacy of lamp should be minimum 100 Lumen per watt. (b) Input Voltage range : 140 to 270 volts (c) Temp operating range : Minus 10°C to Plus 45°C (d) Power factor : Minimum 0.90 (e) CRI : Morethan 80

S&F flush mounting factory made SPN DB 12 way, 240 Volt, Double door, IP-43 protection, IK-09 with metal door with 100 Amps copper bus bar, with neutral bar, earth bar and cables ties for cable management fully insulated bus bar complete all as specified and directed by Engineer-in-charge.

S&F MCB 6 to 32 Amps, Single Pole 240 Volts, 10 KA, ‘C’ Curve, complete all as specified and directed by Engineer-in-charge.

S&F in repair MCB 63 Amps, Single Pole & neutral 240 Volts, 10 KA, ‘C’ Curve, complete all as specified and directed by Engineer-in-charge.

S&F in replacement Energy saving 9/10 watt environmental friendly, ultra modern, energy saving, surface mounted, decorative oval bulk head edge-lit LED luminaire comprising of high brightness LEDs, IP 65 protection fixed on wall complete all as specified and as directed by Engineer-in-charge. Make :- Havells Cat part No HEXAFT10WLED857SSY MBOPC and Crompton cat part No LBHE-10-CDL or equivalent cat part No of makes as mentioned in Appendix 'A'.

S&F in replacement Sub main wiring complete with 2 single core 6 Sqmm (Nominal area) multi stranded copper conductor PVC insulated unsheathed cable FRLSH drawn in and including heavy duty PVC conduit ISI marked not less than 25mm dia concealed including single core multistranded copper conductor 6 Sqmm size cable as earth continuity wire drawn in same conduit complete all as specified and directed by Engineer-in- charge Note : Two runs of 6 Sqmm single core cable and one run of 6 sqmm copper wire earth continuty conductor and conduit with fittings shall be measured as one length. -------------------------------------------------------------------------- Note :- A sum of Rs. 33019/- will be deducted on account of credit for dismantled/ demolished / taken down material. Please refer details on Srl Page No. 23(R) & 24(R) (Schedule of Credit) of Tender documents.

MSR INFRATECH

SHIVA BUILDERS

PACHAR BUILDERS

JK ENGINEERS