REPAIR / MAINT SUBMERSIBLE PUMPING SETS, LT PANELS, WATER LEVEL INDICATORS, DOSING EQUIPMENT AND CERTAIN MISC WORK AT FATEHGARH

Amount

Supply & fix in replacement of DOL Starter 415 Volt suitable for 5 HP motor complete all as specified and directed.

Supply & fix in replacement of Contactor ML-3 rangge 50-70 Amp suitable to operate 40-45 HP submersible pumping set complete all as specified and directed.

Supply & fix in replacement of Contactor ML-2 rangge 35-60 Amp suitable to operate 20-40 HP submersible pumping set complete all as specified and directed.

Supply & fix in replacement of Contactor ML-3 range 60-95 Amp suitable to operate 40-45 HP submersible pumping set complete all as specified and directed.

M&L for cleaning of RCC Over Head Tanks capacity 1 lakh gallon removing and taking out sand, sludge and mud etc including dispossed of the same at a distance not exceeding 100 mtrs from the tank,including two coats of whitewash on whole internal walls of OH Tank complete all as specified and directed . (NOTE:-All the safety equipments for workers working on OHT and U/G Sumps will be provided by the contactor)

All as per item above but for capacity 50000 gallon complete all as specified and directed.

All as per item above but for capacity 40000 gallon complete all as specified and directed.

All as per item above but for capacity 30000 gallon complete all as specified and directed.

All as per item above but for Under Ground Sump capacity 10000 gallon complete all as specified and directed.

M&L for taking out unserviceable submersible pumping set complete with column pipe any capacity and any type from existing bore well carefully without damaging the p/set including connecting parts and lowering the same after repair including provision of suitable size of nut & bolts with washer and suitable packing for column pipes and connection of submersible cable complete all as directed NOTE:- (1) Chain pully block and clamps etc shall be provided by the department. (2) Necessary safety pracaution will be responsibility of the contractor. (3) Parts replaced of submersible pump set shall be measured and paid seperately under relevant item here in after under as supply only. (4) No extra payment will be made to the contractor for note (1) and (2) above

Dismantling of submersible 40 to 41 HP motor and taking out unserviceable spares and burnt copper binding wire complete. M&L for rewinding of submersible motor with insulated copper winding wire including sleeves as per original company and replacement of worn out parts, including grinding & polishing of rotor sleeves and refixing, testing & transport charges complete all as specified & directed Note:(Parts for following items shall be paid under relevent item here-in-after under as supply only).

All as per item above but for 30 HP 35 HP motor complete all as specified & directed

All as per item above but for 25 HP motor complete all as specified & directed

All as per item above but for 15 HP motor complete all as specified & directed

Supply only Impeller suitable for 15 HP motor of existing make/company complete all as specified & directed.

Supply only Neck ring suitable for 15 HP motor of existing make/company complete all as specified & directed.

Supply only Shaft sleeve suitable for 15 HP motor of existing make/company complete all as specified & directed.

Supply only Pump shaft suitable for 15 HP motor of existing make/company complete all as specified & directed.

Supply only Coupling suitable for 15 HP motor of existing make/company complete all as specified & directed.

Supply only Coupling key suitable for 15 HP motor of existing make/company complete all as specified & directed.

Supply only Impeller key suitable for 15 HP motor of existing make/company complete all as specified & directed.

Supply only Stud with nuts suitable for 15 HP motor of existing make/company complete all as specified & directed.

Supply only Thrust bearing suitable for 15 HP motor of existing make/company complete all as specified & directed.

Supply only Lower housing bush suitable for 15 HP motor of existing make/company complete all as specified & directed.

Supply only Upper housing bush suitable for 15 HP motor of existing make/company complete all as specified & directed.

Supply only Rotor shaft sleave suitable for 15 HP motor of existing make/company complete all as specified & directed.

Supply only Drain plug suitable for 15 HP motor of existing make/company complete all as specified & directed.

Supply only Water seal suitable for 15 HP motor of existing make/company complete all as specified & directed.

Supply only CI Bowl suitable for 15 HP motor of existing make/company complete all as specified & directed.

Supply only Rotor Shaft suitable for 15 HP motor of existing make/company complete all as specified & directed.

Supply only ball bush suitable for 15 HP motor of existing make/company complete all as specified & directed.

Supply only Impeller suitable for 25 HP motor of existing make/company complete all as specified & directed.

Supply only Neck ring suitable for 25 HP motor of existing make/company complete all as specified & directed.

Supply only Shaft sleeve suitable for 25 HP motor of existing make/company complete all as specified & directed.

Supply only Pump shaft suitable for 25 HP motor of existing make/company complete all as specified & directed.

Supply only Coupling suitable for 25 HP motor of existing make/company complete all as specified & directed.

Supply only Coupling key suitable for 25 HP motor of existing make/company complete all as specified & directed.

Supply only Impeller key suitable for 25 HP motor of existing make/company complete all as specified & directed.

Supply only Stud with nuts suitable for 25 HP motor of existing make/company complete all as specified & directed.

Supply only Thrust bearing suitable for 25 HP motor of existing make/company complete all as specified & directed.

Supply only Lower housing bush suitable for 25 HP motor of existing make/company complete all as specified & directed.

Supply only Upper housing bush suitable for 25 HP motor of existing make/company complete all as specified & directed.

Supply only Rotor shaft sleave suitable for 25 HP motor of existing make/company complete all as specified & directed.

Supply only Drain plug suitable for 25 HP motor of existing make/company complete all as specified & directed.

Supply only Water seal suitable for 25 HP motor of existing make/company complete all as specified & directed.

Supply only CI Bowl suitable for 25 HP motor of existing make/company complete all as specified & directed.

Supply only Rotor Shaft suitable for 25 HP motor of existing make/company complete all as specified & directed.

Supply only ball bush suitable for 25 HP motor of existing make/company complete all as specified & directed.

Supply only Impeller suitable for 30 to 35 HP motor of existing make/company complete all as specified & directed.

Supply only Neck ring suitable for 30 to 35 HP motor of existing make/company complete all as specified & directed.

Supply only Shaft sleeve suitable for 30 to 35 HP motor of existing make/company complete all as specified & directed.

Supply only Pump shaft suitable for 30 to 35 HP motor of existing make/company complete all as specified & directed.

Supply only Coupling suitable for 30 to 35 HP motor of existing make/company complete all as specified & directed.

Supply only Coupling key suitable for 30 to 35 HP motor of existing make/company complete all as specified & directed.

Supply only Impeller key suitable for 30 to 35 HP motor of existing make/company complete all as specified & directed.

Supply only Stud with nuts suitable for 30 to 35 HP motor of existing make/company complete all as specified & directed.

Supply only Thrust bearing suitable for 30 to 35 HP motor of existing make/company complete all as specified & directed.

Supply only Lower housing bush suitable for 30 to 35 HP motor of existing make/company complete all as specified & directed.

Supply only Upper housing bush suitable for 30 to 35 HP motor of existing make/company complete all as specified & directed.

Supply only Rotor shaft sleave suitable for 30 to 35 HP motor of existing make/company complete all as specified & directed.

Supply only Drain plug suitable for 30 to 35 HP motor of existing make/company complete all as specified & directed.

Supply only Water seal suitable for 30 to 35 HP motor of existing make/company complete all as specified & directed.

Supply only CI Bowl suitable for 30 to 35 HP motor of existing make/company complete all as specified & directed.

Supply only Rotor Shaft suitable for 30 to 35 HP motor of existing make/company complete all as specified & directed.

Supply only ball bush suitable for 30 to 35 HP motor of existing make/company complete all as specified & directed.

Supply only Impeller suitable for 40 to 41 HP motor of existing make/company complete all as specified & directed.

Supply only Neck ring suitable for 40 to 41 HP motor of existing make/company complete all as specified & directed.

Supply only Shaft sleeve suitable for 40 to 41 HP motor of existing make/company complete all as specified & directed.

Supply only Pump shaft suitable for 40 to 41 HP motor of existing make/company complete all as specified & directed.

Supply only Coupling suitable for 40 to 41 HP motor of existing make/company complete all as specified & directed.

Supply only Coupling key suitable for 40 to 41 HP motor of existing make/company complete all as specified & directed.

Supply only Impeller key suitable for 40 to 41 HP motor of existing make/company complete all as specified & directed.

Supply only Stud with nuts suitable for 40 to 41 HP motor of existing make/company complete all as specified & directed.

Supply only Thrust bearing suitable for 40 to 41 HP motor of existing make/company complete all as specified & directed.

Supply only Lower housing bush suitable for 40 to 41 HP motor of existing make/company complete all as specified & directed.

Supply only Upper housing bush suitable for 40 to 41 HP motor of existing make/company complete all as specified & directed.

Supply only Rotor shaft sleave suitable for 40 to 41 HP motor of existing make/company complete all as specified & directed.

Supply only Drain plug suitable for 40 to 41 HP motor of existing make/company complete all as specified & directed.

Supply only Water seal suitable for 40 to 41 HP motor of existing make/company complete all as specified & directed.

Supply only CI Bowl suitable for 40 to 41 HP motor of existing make/company complete all as specified & directed.

Supply only Rotor Shaft suitable for 40 to 41 HP motor of existing make/company complete all as specified & directed.

Supply only ball bush suitable for 40 to 41 HP motor of existing make/company complete all as specified & directed.

Supply & fix in replacement of Water pressure guage 100 mm dia in size ranging 0 to 25 kg/ sq cm calibration complete with size 3/8"X1/2" and brass cock 1/2" dia complete all as directed.

Supply & fix in replacement of electronic Timer for Star Delta Starter type ETSD2 Cat No TESD 2 timing range 3-30 sec complete all as specified and directed.

Supply & fix in replacement of Single Phase Preventor suitable for 15/25/35/41 HP submersible pumping set motor complete all as specified and directed.

Supply & fix in replacement of overload protection relay for FASD starter ranging 28-42/30-35 Amp complete all as specified and directed.

S&F in replacement of Digital type ampere meter of size 96x96mm with CT 100/5 Amp,AC,3 phase,415 volts complete all as specified & directed.

S&F in replacement of Digital type voltmeter of size 96x96mm AC, 3P, 415 volts complete all as specified and directed.

Supply,fixing ,testing and commissioning submersible cable ,flat, 16 sqmm,3 core,PVC insulated and PVC sheathed with multi stranded, copper conductor,1100 Volts grade ,fixed to submersible motor column pipe ,using suitable size of clamps made out of stainless steel flat of size 20 x2 mm with steel nuts ,bolts & washer for every column pipe of 3 m length complete all as specified and directed.

Supply,fixing ,testing and commissioning submersible cable ,flat, 10 sqmm,3 core,PVC insulated and PVC sheathed with multi stranded, copper conductor,1100 Volts grade ,fixed to submersible motor column pipe ,using suitable size of clamps made out of stainless steel flat of size 20 x2 mm with steel nuts ,bolts & washer for every column pipe of 3 m length complete all as specified and directed.

M&L in replacement of star delta starter without sheet metal enclosure fixed in existing panel for FASD starter with relay ranging 45 to 70 Amps, suitable for submersible pumping 3 Phase,415 Volts,50 Hz including single phase preventor complete all as specified and directed.

M&L in replacement of star delta starter without sheet metal enclosure fixed in existing panel for FASD starter with relay ranging 30 to 50 Amps, suitable for submersible pumping 3 Phase,415 Volts,50 Hz including single phase preventor complete all as specified and directed.

S&F in replacement MCCB , 4 pole, 415 Volt, fixed type 315 amp with breaking capacity 35 kA including complete electrical connection using appropirate size of copper lugs complate all as specified and directed.

S&F MCCB , 4 pole, 415 Volt, adjustable type 250 Amp with breaking capacity 36kA including complete electrical connection using appropirate size of copper lugs complate all as specified and directed.

S&F in replacement MCCB , 3 pole, 415 Volt, fixed type 200 amp with breaking capacity 36 kA including complete electrical connection using appropirate size of copper lugs complate all as specified and directed.

S&F in replacement MCCB , 3 pole, 415 Volt, fixed type 125 amp with breaking capacity 16 kA including complete electrical connection using appropirate size of copper lugs complate all as specified and directed.

S&F in replacement MCCB , 3 pole, 415 Volt, fixed type 100 amp with breaking capacity 16 kA including complete electrical connection using appropirate size of copper lugs complate all as specified and directed.

S & F in replacement synthetic rubber insulated mats 2 mm thick for voltage upto 3.3 kV for electrical purpose as per IS 15652 of 2006 (superseding IS 5424) suitable for electrical shock safety of size 2 m x 1 m completed all as specified and directed.

M & L for painting of rising , delivery , overflow and washout pipes of various capacity OH tank with Blue, green, red and yellow colours respectively with syntheic enamel paint two coats including marking with arrows ( directions of flow ) and writing date of cleaning with white synthetic enamel paint over black ( syntjetic enamel paint ) background of size (300mm x 300mm) completed all as specified and directed.

M/S S P CONSTRUCTION