REPAIR TO FLOORS, SUNKEN FLOORS, PLUMBING AND SANITARY FITTINGS OF CERTAIN BUILDINGS IN NO 1 AREA AT AFS PTK

Amount

Brick work with sub class B bricks straight or curved on plan exc 6m mean radius built in cm 1:6 including demolition of existing brick work complete all as specified and directed by Engineer-in-Charge

All as above item No 01above, but except bricks complete all as specified and directed by Engineer-in-Charge

Providing precast cement concrete, PCC 1:2:4, type B-0 (using 12.5 mm graded crushed stone aggregate), as in louvres and jallies, 25mm thick (measured solid), including all mouldings, set in CM 1:4 complete all as specified and directed by Engineer-in-Charge

Reinforced cement concrete (Nominal mix) 1:2:4 (12.5 mm graded aggregate), type B-0 (using 12.50mm graded crushed stone aggregates as in Slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in the shelves and the like complete all as specified and directed by Engineer-in-Charge

Mild steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mmdia or securing with clips quality conforming to Fe-310-O or Fe-410-O complete all as specified and directed by Engineer-in-Charge.

Rendering 15mm thick cement plaster in CM 1:4 on bricks or concrete surfaces finishing the surfaces even and smooth without using extra cement, with two coats of exterior emulsion paint on new surface complete all as specified and directed by Engineer-in-Charge Note : Rate for form work if requd to be included in the rate quoted by the contractor

Rendering 15mm thick cement plaster on faces of brick work or concrete surfaces in cement mortar (1:6) finished even and fair without using extra cement, including taking down existing plaster with two coats of OBD of any tint over a white wash complete all as specified and directed by Engineer-in-Charge

Applying 3mm thick wall care putty on wall surfacescomplete all as specified and directed by Engineer-in-Charge

Rendering 15mm thick cement plaster in CM 1:4 on bricks on concrete surfaces finishing the surfaces even and smooth without using extra cement including two coats of exterior emulsion paint on new surface , incl taking down existing plaster complete all as specified and directed by Engineer-in-Charge. Note :Rate for form work if reqd to be incl in the rate quoted by the contractor.

Rendering dubbing coat over damaged irregular surface of chajjas roof projections ceiling facia etc average 15mm thick in cm 1:4 over cement slurry coat thick @ 3 Kg/sqm making the surface even followed by 5mm thick rendering in CM 1:3 furnished even& smooth including applying two coats of weather proof emulsion paint incl making of drip course as reqd complete incl roughening surface of old concrete by picking sweeping clean and washing with water complete all as specified and directed by Engineer-in-Charge. Note :Rate for form work if reqd to be incl in the rate quoted by the contractor.

Rendering or plastering work 10mm thick in CM 1:3 in fascia or edging of Chajjas, ceiling and roof projections etc, including taking out pealed off plaster / concrete and making the line in true shape and finishing the surface without using extra cement including applying two coats of weather proof emulsion paint for facia, chajja, and roof projection etc complete all as specified and directed by Engineer-in-Charge

Cement concrete 1:3:6 type C-2 (using 40mm graded agg) as in plinth, 75mm thick and finished even and smooth without using extra cement, including demolition of existing cement concrete complete all as specified and directed by Engineer-in-Charge

Cement concrete 1:2:4, 40mm thick type B-2 (using 20mm graded agg) as in Floor, finished even and smooth without using extra cement, including demolition of existing cement concrete complete all as specified and directed by Engineer-in-Charge

Supply only glass dividing strip 3mm thick, 38mm wide and inserted in position to conform to design complete all as specified and directed by Engineer-in-Charge

Non-skid coloured ceramic tiles 7 to 8mm thick (square /rectangular) area of each tile exceeding 0.11sqm but not exceeding 0.18 sqm as in floor etc set and jointed in neat cement slurry and pointed in white or coloured cement to match the tiles including 15mm thick screed bed or bedding layer in CM 1:4 and dismantling/demolition on existing surface complete all as specified.and directed by Engineer-in-Charge

Vitrified tiles light shade 10mm thick (square/rectangular) area of each tile not exceeding 0.36 sqm as in floor etc set and jointed in neat cement slurry and pointed in white or coloured cement to match the tiles including 15mm thick screed bed or bedding layer in CM 1:4 and dismantling/ demolition on existing surface complete all as specified and directed by Engineer-in-Charge

Glazed ceramic coloured tiles of size 450 x 300 x 7mm thick, on vertical surfaces of walls such as skirting dado etc. set and jointed in neat cement slurry and pointed in white or colour cement to match including 10mm thick rendering in cement mortar 1:4 and dismantling existing wall tiling complete, all as specified.and directed by Engineer-in-Charge

Rotational moulded polyethylene water storage tank 3 layer white colour water tank , non- toxic effect, algea formation protection (made from Virgin grade of polyetjylene material which is duly stablized with anti-oxidentPlastic) of capacity 500 litres, (cylindrical vertical one piece moulded with closed top), the internal and external surfaces of tanks are smooth, clean and free from any hidden internal defects, hoisted and fixed in position including S & F necessary GI fittings, inlet/outlet washout, overflow pieces long nipples, checknuts & washer ,20 mm dia PTMT valves high pressure of PTMT with epoxy coated Aluminum rod & high-density plastic ball and 20 mm brass stop cock etc complete including dismantling existing water tank all as specified and directed by Engineer-in-Charge

Rotational moulded polyethylene water storage tank 3 layer white colour water tank , non- toxic effect, algea formation protection (made from Virgin grade of polyetjylene material which is duly stablized with anti-oxidentPlastic) of capacity 1000 litres, (cylindrical vertical one piece moulded with closed top), the internal and external surfaces of tanks are smooth, clean and free from any hidden internal defects, hoisted and fixed in position including S & F necessary GI fittings, inlet/outlet washout, overflow pieces long nipples, checknuts & washer ,20 mm dia PTMT valves high pressure of PTMT with epoxy coated Aluminum rod & high-density plastic ball and 20 mm brass stop cock etc complete including dismantling existing water tank all as specified and directed by Engineer-in-Charge

S & F in repair 15mm bore tubes medium grade galvanized ISI marked with all fittings short pieces and fixed complete to walls, floor, ceiling etc all incl taking down existing G I tubing as specified and directed by Engineer-in-Charge

All as per Srl item No 20 above, but fixing only

S & F in repair 20mm bore tubes medium grade galvanized ISI marked with all fittings short pieces and fixed complete to walls, floor, ceiling etc all incl taking down existing G I tubing as specified and directed by Engineer-in-Charge

All as per Srl item No 22 above, but fixing only

Cutting chases pinning in brick work for concealing water tubing and making good to facing where required and pointing in cement motar 1:3, cutting n.exc. 10cm girth all as specified and directed by Engineer-in-Charge

Supply and fix in repair Vetreous China squatting pan Orissa pattern size 580 x 440mm white with integral foot rest (excluding flushing cistern and flush pipe), including long Arm P-trap (CI) 100 mm dia of length up to 700 mm or as per site requirement , complete incl making good to floor all as specified and directed by Engineer-in-Charge

Supply and fix in repair Vitreous China wash down water closet pan (pedestel pattern) white,including trap connection to drain (outgoing pipe) and to flushing pipe, antisyphonage pipe, PVC jet for Pedestal pattern pan including 450/600mm long PVC connection and plastic water closet seat of white in colour,back closed pattern with flat bottom,and cover and mild steel chromium plated or aluminised hinging device etc complete all as specified and directed by Engineer-in-Charge

Supply and fix in repair Vitreous china wash hand basin white of bowl size 550 x 440mm including waste coupling and PVC waste pipe, 32mm dia, 15 mm dia bore pipe pillar tap cast copper alloy with capstan heads chromium plated fancy to be fixed in M S brackets complete all as specified and directed by Engineer-in-Charge

Supply and fix in repair 10 ltr capacity PVC valveless syphonic action type flushing cistern low level white with inlet ball valve float ovel handle incl brackets and PVC flushing pipe of polyethylene of low or high density or PVC 32mm dia complete all as specified and directed by Engineer-in-Charge

Supply and fix in repair PVC connection 15mm bore size with two nuts and washers of length 450mm all as specified and directed by Engineer-in-Charge

Supply and fix in repair Cabinet mirror plastic body for toilet of size 350x450mm with 4mm thick looking mirror complete all as specified and directed by Engineer-in-Charge

Supply and fix in repair Sinks with drainage board made of stainless steel 1 mm thick kitchen or laboratory with plugs, washers and wastes, including 32mm dia waste pipe and CP grating and bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 915mm x 460mm, bowl size 410mm x 330mm x 160mm all as specified and directed by Engineer-in-Charge

S & F in replacement Stainless steel plate rack of size 900mm X 900mm X 250 mm all as specified and directed by Engineer-in-Charge

Supply and fix sinks made of stainless steel 1mm thick kitchen or laboratory with plugs, washers and wastes, including 32 mm dia waste pipe and CP grating and bedding in cement mortar to dwarf wall or demolition of existing cemented/ marble kitchen sink and making good with providing Marble strip overall size of sink 610 x 460mm and bowl size 550x400mm complete all as specified and directed by Engineer-in-Charge. Note : Marble will be measured and paid separately.

Marble work 18 to 20mm thick as in cooking platform and like (makarana white) in cement mortar 1:4 including pointing in white cement 1 : 2 using marble dust with admixture of pigment to match with existing shed

Supply and fix in repair 15 mm dia stop valve/angle valve chromium plated with long shank concealed type cast copper alloy ISI marked with crutch or butter fly handle high pressure screwed down complete all as specified and directed by Engineer-in-Charge

S & F in repair 15mm stop valve cast copper alloy screwed down high pressure with crutch butter fly handle screwed bot ends for iron pipe or for unions complete all as specified and directed by Engineer-in-Charge

S & F in repair 20mm stop valve cast copper alloy screwed down high pressure with crutch butter fly handle screwed bot ends for iron pipe or for unions complete all as specified and directed by Engineer-in-Charge

Supply and fix in repair Cast copper alloy CP shower arm arm 190mm long heavy casted body with wall flange complete all as specified and directed by Engineer-in-Charge.

Supply and fix in repair Brass chromium plated shower rose 125mm size with swivel joints fixed in repairs including fixing to steel pipe or union all as specified and directed.

PCC 1:4:8, type D-2, (using 40mm graded crushed stone aggregate) in foundation filling and mass concrete, (as in sunken floor) with spout pipe 50 mm dia up to 600 mm long or as per site requirement including demolition of existing surface complete all as specified and directed by Engineer-in-Charge

Doctor fixit Pidifin 2k high performance 2 component flexible Acrylic polymer modify cement base water proofing coating in two coat 1mm thick dry film mixed in ratio 2:1 by weight or 1.5:1 by volume complete all as specified and directed by Engineer-in-Charge

Supply and fix in repair 100mm/75mm bore cast iron floor trap with CP grating including jointing to waste pipe fixed in cement concrete type B-1, 1:2:4, complete all as specified and directed by Engineer-in-Charge

Supply and fix in repair Grating round with/ without hole 100mm/75 mm size of CP complete all as specified and directed by Engineer-in-Charge

Supply and fix in repair 100mm bore sand cast iron soil waste and vent pipe ISI marked in any length with or without ears with lead joints laid in floor/walls all as specified and directed by Engineer-in-Charge

All as above item No 45 above, before but 75mm bore.

Supply and fix in repair 100mm dia cast iron bends (any radius) diminishing pieces or tapers (larger bore measured) complete all as specified and directed by Engineer-in-Charge

Supply and fix in repair 75mm dia cast iron bends (any radius) diminishing pieces or tapers (larger bore measured) complete all as specified and directed by Engineer-in-Charge

Supply and fix in repair 100mm dia, branch pieces, single (equal or unequal) ordinery or inverted (spigot or socket type) or with parallel branches complete all as specified and directed by Engineer-in-Charge

Supply and fix in repair 75mm dia, branch pieces, single (equal or unequal) ordinery or inverted (spigot or socket type) or with parallel branches complete all as specified and directed by Engineer-in-Charge

Supply and fix in repair 100mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floor complete all as specified and directed by Engineer-in-Charge

Supply and fix in repair 100mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints, fixed to walls complete all as specified and directed by Engineer-in-Charge

S & F in repair 100mm bore PVC (SWR) bends copmplete all as specified and directed by Engineer-in-Charge

S & F in repair 100mm bore PVC (SWR) single T complete all as specified and directed by Engineer-in-Charge

Removing of vegetation / plantation on the wall/ roof/ any position of up to double storey building including necessary scaffolding upto 6 m height and roots superfacial area n.exc 2 sqm each and making good of surface by applying chemical treatment with GLYPHOSATE 41% including removing /refixing of CI/GI pipe lines complete.(Note : Brick work, plaster and CI/GI pipe lines shall be measured and paid separately)

GI spout pipe medium weight 50mm bore dia of length 450mm set in PCC 1:4:8 porous concrete and make the external portion with CM 1:3 with and including water proofing @ 200 ML per bag complete all as specified and directed by Engineer-in-Charge.

Textured heavy duty exterior vitrified tiles of size 300x300x10mm thick ,set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including a screed bed of 15mm thick in CM (1:4) complete, all as specified and directed by Engineer-in-Charge

Pressed steel frame made out of MS sheet 1.25mm thick of size 125x60mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate etc including filling of concrete 1:3:6 type C-1 back of chowkhats, with two coats of synthetic enamel paint over one coat of red oxide primer including taking down with existing one all as specified and directed by Engineer-in-Charge NOTE: During Fixing of chowkhat, surface Shall be make good in plumb with existing finishes like cement plaster, similar wall tile,floor tile etc and as per site requirement.

Pressed steel frame made out of MS sheet 1.25mm thick of size 105x60mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate etc including filling of concrete 1:3:6 type C-1 back of chowkats,with two coats of synthetic enamel paint over one coat of red oxide primer including taking down with existing one all as specified and directed by Engineer-in-Charge NOTE: During Fixing of chowkhat, surface Shall be make good in plumb with existing finishes like cement plaster, similar wall tile,floor tile etc and as per site requirement.

35mm thick (factory made) plain framed panelled door shutters of 2nd class hard wood two panel with lock rail and panel of 9mm thick BWP commercial ply ,the size of rail and style as per IS : 1003 Part-I, Kiln seasoned and chemically pressure treatedfactory made shutters wood is to be incorporated all as specified,including two coat of synthetic enamal paint over one coat of pink primer complete all as specified and directed by Engineer-in-Charge

Preparation of new or previously untreated surfaces of wood or based materials of any description not otherwise described over 10cm width or girth & applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and directed by Engineer-in-Charge

Factory made solid PVC door frame single rebated of size 60 x 30mm made out of solid PVC foam with homogenous fine cellular structure having smooth outer integral skin with suitable metal stiffner and fixed with 100x8 sheet metal CSK screws taking down with existing one complete all as specified and directed by Engineer-in-Charge NOTE: During Fixing of chowkhat, surface Shall be make good in plumb with existing finishes like cement plaster, similar wall tile,floor tile etc and as per site requirement.

Supply and fix in repair Factory made PVC Flush door of 33 to 35 mm thick overall thickness comprising of 19 SWG MS tube of size 19 x 19 mm (19 gauge) covered with 5mm thick PVC Sheet, (any colour as approved) on both sides core shall be filled with 19mm to 20mm thick PVC solid board taking down with existing one complete all as specified. Note : All screws shall be self tapping chroming plated all as specified and directed by Engineer-in-Charge.

Factory made PVC prelam fully glazed/wire gauge shutter (single piece Both side), 33 to 35 mm thick consisting of frame made up of MS tube of size 25mm x 25mm (19 gauge) for top & bottom rail, and in styles. Single piece plane coloured PVC sheets of 5mm thick to be used to cover style & rails. For edges, PVC sheets strip of 20mm thick struck inside with solvent cement. Plane colour PVC sheet for top rail, lock rail & bottom rail on either side & as gap insert with PVC board 22mm to 25mm solid core board. Panel shall be of wire gauge stainless steel wire cloth 0.25mm to 0.36mm nominal dia of wire and average width of aperture 1.4mm to 2mm. Stainless steel wire cloth shall be covered with aluminum XPM in rhombus shape in one piece from top to bottom rail, complete all as specified and directed by Engineer-in-Charge. Note : All screws shall be self tapping chroming plaed and length of Screw not less than 50 mm.

Supply and fix in repair Factory made Steel window/ Ventilator 1.25mm thick box type(primer coated)ERW hollow P section of size 60mmx25mm including grill using 10 sqmm bar double rebated both gauge and glass shutter comprised gauged glazed Skelton shutter ERW sec 50mmx20mm and 1mm thick with two openable leaf consisting two Nos sash bar of T Section 20mmx3mm complete welded to frame with one vertical mullion of ERW box type T Section of size 60mmx25mm and 1.25mm thick refer TD Drawing No CEAF/AR-480/2015 Sheet No 2(A)/4 dated 30.12.2015 including cutting holes and good dismantled portion in PCC(1:2:4) type B1 and match the disturbed portion with existing surface four Nos for each window including following fitting welded to frame shutter : (a) Hold fast,150mm long of 12mmx3mm made to shape O4 Nos per window (b) handle of Z Sec20mmx25mm, 100mm long-per No leaf (c) MS Tower bolt 150mm long-02No per leaf . (d) Z section 20mmx25mm, 100mm long stopper 1 No per leaf. (e) cleat 55mm long of hollow square 15mmx20mmx63mm welded to hinge. 1 No per leaf (f) MS Pintal hinges of size 75mmx12mm. 2 Nos per leaf, (g) Stainless steel wire cloth, 0.25 mm to 0.36mm nominal dia of wire & average width of aperture 1.40mm to 2mm & fixed with alluminium wire staples (h) Glass pane 3mm thick fixed with MS pin and oil putty (j) Including two coats of synthetic enamel paint complete. NOTE: During Fixing of window, surface Shall be make good in plumb with existing finishes like cement plaster, similar wall tile,floor tile etc and as per site requirement.

Stainless steel wire cloth, 0.25 mm to 0.36mm nominal dia of wire & average width of aperture 1.40mm to 2mm & fixed with alluminium wire staples in repair complete all as specified and directed by Engineer-in-Charge

3mm thick sheet glass ordinery quality and glazing with oil putty in square n exc. 0.50 Sqm in each pane including hacking out broken glass complete all as specified and directed by Engineer-in-Charge

Stainless steel butt hinges medium weight 100mm all as specified and directed by Engineer-in-Charge. NOTE :- All screws shall be self tapping chrome plated and length of screw not less 38 mm

300mm, Mild steel spring for door, ordinary rat tail rod pattern springs, including roller and roller plate complete all as specified and directed by Engineer-in-Charge

Stainless steel Hasp and staple of 100 mm long fixed with Self Tapping screws complete all as specified and directed by Engineer-in-Charge

18 mm thick UV board duly edge banded with 0.8 mm thick PVC taping fitting of shutters shall be fixed with and including continous piano steel hinges and modular handles, design and colour as approved by GE suitable for cup board etc including taking down with existing one complete all as specified and directed by Engineer-in-Charge

Supply and fix in repair Shelves made of HDHMR board 18 mm thick water proof with life time warranty for anti-termite shall be duly edge banded with PVC taping 0.8 mm thick, cut to shape & size of shelves complete all as specified and directed.

S & F in repair stainless steel nipple of size 25mm complete all as specified and directed by Engineer-in-Charge

S & F in repair stainless steel nipple of size 35mm complete all as specified and directed by Engineer-in-Charge

S & F in repair stainless steel nipple of size 50mm complete all as specified and directed by Engineer-in-Charge

Removing building materials etc (other than spoil payable under items 99 to 102 in section-03, Earth work of SSR-2004- Part II Rates) to a distance exceeding 4.5 KMm but not exceeding 5 Km including loading, unloading and spreading st the destination if required/ directed by the Engineer-in-Charege complete all as specified (the weight/ Load calculated as per preamble given on Srl Page No 431 of SSR 2004 Part II)

S & F in repair 75 mm dia PVC (SWR) floor trap, plain with grating including jointing with solvent cement complete all as specified and directed by Engineer-in-Charge

S & F in repair 15 mm dia PVC SYMET bib cock long nose with flange complete all as specified and directed by Engineer-in-Charge

Preparation of old plastered or un plastered surfaces of wall including cornices, etc apply two coats of oil bound distemper on old surfaces of walls complete all as specified and directed by Engineer-in-Charge

Preparation of old painted wooden surfaces of any description and in any situation over 10 cm width or grith and applying one coat of synthetic enamel paint complete all as specified and directed by Engineer-in-Charge

Preparation of old painted steel surfaces of any description and in any situation over 10 cm width or grith and applying one coat of synthetic enamel paint complete all as specified and directed by Engineer-in-Charge

Dismantling post or struts (wood, steel or RCC) any section incl taking out embedded portion in natural ground and making good complete all as specified and directed by Engineer-in-Charge

PCC (1:5:10) type E-2 using 40mm graded aggregate as in fdn/ mass filling, concrete complete all as specified and directed by Engineer-in-Charge

Post and struts/ faltiron in fencing all necessary drilling bolting or reveting etc and similar work confirming to Fe-290 gde 165 complete all as specified and directed by Engineer -in-Charge

Preparation of new steel surfaces including preparation of surfaces and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed by Engineer-in-Charge

Black bituminious paint of tow coat of any description wood, steel, iron, concrete, brick, stone surfaces etc exe 10 com in width or girth complete all as specified and directed by Engineer-in-Charge

supply Only chain link fencing using 4mm dia GI wire 75 x 75 mm mesh (weight not less than 4kg/ Sqm) including line wires, any mesh, size & type to any type of standards, rails, straining bolts, etc including provision of binding wire and dismantling of existing chain likn fencing complete all as specified and directed by Engineer-in-Charge

Hexagonal bolts, nuts 5mm to 100 mm dia and length of bolt exe 5cm but n exe 10 cm long complete all as specified and directed by Engineer-in-Charge

M/S RELIANCE ENGINEERS

INDERJIT SINGH

M/S HEAVEN BUILDERS AND ENGINEERS

M/S J N TRADERS

pardeep singh marwaha

Vijay Kumar Contractor and Engineers

Ms Dalip Kumar and Co.

M/S G P MARWAHA