ADDN ALTN TO BUILDING NO P67 P69 AND P75H PROVN OF CEILING HARDSTANDING AND ASSOCIATED WORKS NEAR BLDG NO P918 AND PROVN OF COMPOUND WALL AND ALLEID WORKS IN PJ ENCLAVE UNDER GE AF BAMRAULI

Amount

Excavating in post holes (or similar holes) each not exc 0.5 cum, getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25cm, watering, and removing surplus soil to a distance not exc 50m and making good surface, work in hard/dense soil complete all as specified and directed.

M & L for PCC 1:3:6 Type C2 using 40mm graded aggregate as in foundations, filling and mass concrete complete all as specified and directed.

S & F steel work tubular trusses incuding special shaped washer etc complete using ERW Welding or induction butt welded tubes conforming to IS 1161 1979 grade st 240 complete all as specified and directed.

S&F pre-painted galvalume aluminum zinc coating GI based corrugated steel sheeting 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering / cladding to wall, fixed with self tapping screws as specified and directed.

M & L for applying two coats of synthetic enamel paint over a coat of red oxide primer on newly steel surfaces of any description over 10 cm in width or grith, not otherwise described including preparation of surfaces complete all as specified and directed.

Taking down Chowkats or frames with shutter exceeding 1.5 Sqm but not exceeding 4 Sqm each (Without taking off shutters from the frames) complete all as specified and directed.

S&F 150mm, long, aluminium anodised barrel tower bolt of extruded section and fixed complete all as specified and directed.

S&F 150 mm long , aluminium handles cast type, anodised and fitted complete all as specified and directed.

S&F for powder coating Anodised aluminium frame for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc. complete all as specified and directed. (minimum thickness of powder coating 50 micron).

Aluminium (powder coated) sliding glazed shutter of suitable size with necessary joining cleats, glazing clips, rubber gasket, aluminium snap beading and locking arrangement at both end all as specified and as shown and drawing. Notes : (i) Frame and Glass filling in panels to windows shall be measured and paid for separately under respective item. (ii) Thickness of powder (epoxy polyster) coating shall not be less than 50 Micron (iii) Shade/tint of powder coating (epoxy polyster) shall be as approved by GE. (iv) Aluminium section shall be as per drg No. CE/ALD/TD-194 sheet No. 1/2 & 2/2

S&F 5.50mm thick coloured Sheet glass, best quality and glazing with aluminium clips in square exc 0.5 sqm in each pane complete all as specified and directed.

S&F for 9mm thick prelaminated particle board exterior grade prelaminated both side with decorative choice laminations fixed with screws to aluminium door etc commplete all as specified and directed.

S&F for Stainless steel concealed door closer/over head in floor mounted best quality, suitable for door shutters of 851 to 1000 mm in width and (overall length of cover plate) 140mm etc ccomplete all as specified and directed.

S&F rebated mortice aluminium lock verticle type size 100mm with 4 levers complete all as specified and directed.

Demolition of brick work or stone/boulder masonry, built in cement mortar including all quoins, pillars etc. complete all as specified and directed.

Demolition of reinforced cement concrete of any description and in any position as in ground foors complete all as specified and directed.

M & L for Reinforcement cement concrete pre-cast reinforcement cover slab (1:2:4) type B-1 using( 20 mm graded crushed stone aggregate) RCC ring/Frame and MS frame set in CM (1:4) etc complete all as specified and directed.

M & L for TMT bars 8 mm dia and over cut to length, bent to shape required including cranking, bending, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia complete all as specified and directed.

Excavation over areas, not exceeding 1.5 mtr depth and getting out loose soft soil etc complete all as specified and directed.

M&L for returning filling in , including spreading , levelling , watering and well ramming in layers not exc 25 cm complete all as specified and as directed.

M&L for brick work with sub class B bricks with old size bricks straight or curved on plan exceeding 6 m mean radius built in CM (1:6) complete all as specified and directed.

M&L PCC 1:4:8 type D 2 using 40 mm graded stone aggregate as in sub base of flooring / fdn of wall etc complete all as specified and directed.

M&L for PCC 1:2:4 type B 1 using 20mm graded stone aggregate as in bed blocks, copings and like including weathering, slightly rounded or chamfered angles and throating complete all as specified and directed.

M&L for providing precast cement concrete jallies type B0 ( 1:2:4) using 12.5 mm graded stone aggregate, 25 mm thick measured solid including all mouldings but excluding frames set in cement mortor 1:4 complete all as specified and directed.

M&L for rendering 15mm thick in cement mortar CM 1:4 in two layer (First coat 10 mm thick and second coat 5 mm thick) complete all as specified and directed.

M&L for preparation of newly plastered surafces of walls and applying two coats of cement base paint complete all as specified and diretced.

M& L for removing excavated material n. exc 50 m and depositing where directed at a level n. exc 1.5 mtr above the starting point complete all as specified and directed.

Taking down cement plaster of any description on brick or stone walls etc including raking out joints, hacking out for key, scrubbing down with water etc complete all as specified and directed.

M&L for applying two coats pidifin 2K mixed with cement as in flooring and walls in cement in ratio 1:1 @ 1liter per Sqm with min interval of 4 hours in each coat, including 15 mm thick rendering in CM 1:4 complete incl finished even & smooth without using extra cement complete all as specified and directed. Note: Make of chemical to Dr.Fixit.Gaurantee to be required from the Dr Fixit. All rates including the supply and applying Dr fixit chemical and work to be executed with authorised technician of Dr Fixit

M&L for two coat of premium exterior weather proof coat Apex Ultima or equivalent over and including one coat of primer over 3 mm thick wall care putty including complete removal of existing treatment and preparation of new wall surfaces complete all as specified and directed.

M&L for two coat of premium exterior weather proof coat Apex Ultima or equivalent over and including one coat of primer over 3 mm thick wall care putty including complete removal of existing treatment on wall surfaces complete all as specified and directed.

M&L for two coats of premium exterior weather proof paint Apex Ultima or equivalent over and including one coat of primer on Jafri walls/ grit finish walls including complete removal of existing treatment on wall surfaces complete all as specified and directed.

M&L for preparation of old painted steel surfaces of any description not otherwise described over 10cm width or girth and applying one coat of synthetic enamel paint complete all as specified and directed.

M&L for preparation of old painted wooden surfaces of any description not otherwise described over 10cm width or girth and applying one coat of synthetic enamel paint complete all as specified and directed.

M&L for providing support with mild steel angle and MS plate incl necessary welding etc as in Chajjas up to 6 mtr height including making groove to insert MS sheet and embedded in PCC 1:2:4 type B 2 using 20mm graded stone aggregate including necessary scaffolding to fixing in position and scaffolding should be kept at site for minium 07 days to hold the MS Plates complete all as specified and directed.

S&F in repair vitreous china wash down water closet pan (one piece type) ivory with PVC sheet cover & flushing cistern, flushing pipe), including making good the floor with adjacent floor finishing and making connection to flush pipe etc complete including making functional and removal rubbish/waste materials to a distance n. exc 50m, complete all as specified and directed. Make of WC : ( Hindware Cat No 92043 (INOX) and CERA-COMFY Cat Part No 2075)

Dismantling floor hearth or wall tilling including cement mortar bedding , removing unserviceable tiles and rubbish off the premises for minor repair to floor tiles/ nahani traps / concealed stop cock and GI tubing in wall etc in patches complete all as specified and directed.

S&F for non skid ceramic coloured tiles 300mmx300mmx 7 to 8mm thick in floor set and jointed neat cement slurry and pointed in coloured cement to match over and including 15 mm thick screed bed in cement mortar 1:6 complete all as specified and directed.

M&L for glazed ceramic coloured/ degital designer series tiles including highlighter on verticle or horizontal surface of size 300X450X7to 8mm thick set and jointed with cement slurry and pointing in white cement and pignent to match over and including 10mm thick backing in cement mortar 1:4 in skirting / dado complete all as specified and directed.

M & L for Vitrified ceramic double charged nano finish tiles Light Shade 10mm thick (square/rectangular) polished, area of each tiles not exceeding 0.36sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15mm thick screed bed or bedding layer in CM 1:4 for laying tiles in floors etc. complete all as specified and directed.

S&F Pre-painted galvalume aluminum zinc coating GI based plain steel sheet 0.50mm thick of an colour having tensil strength of 550 Mpa as in roof covering/cladding to wall fixed with self tapping screws complete all as specified and directed.

S&F plain Aluminium 0.71mm thickness sheeting Alloy 31000H4 in valley gutter drip and straight flashing (length and girth and fixed) complete all as specified and directed.

S&F plate girder or single stanchions, built up of one beam or channel section with flange plates, caps, bases splices angle brackets cleats and other connections complete all as specified and directed.

M&L for PCC 1:2:4 type B-2 (Using 40mm graded stone aggregate) as fdn filling and mass concrete for post holes complete all as specified and directed.

M&L for 15mm thick rendering in CM 1:6 on fair faces of brick work, surfaces finished even and fair without using extra cement complete all as specified and directed.

M&L for preparation of new plastered surface of wall and applying two coats of cement base paint over a coat of primer complete all as specified and directed.

M&L for preparation of new plastered surface of wall and applying two coats of oil bound distemper over and including a coat of primer and birla white wall care Putty on wall obtain smooth finish etc including balance area complete removal complete all as specified and directed.

S&F POP false ceiling over GI snap grid permiter wall channel 25x25m fixed on wall all round, GI main ceiling channel with flange 50x25mm @ 250mm C/C, cross GI channel section 25x12 mm @ 750 C/C alongwith the suspenders of GI angle 25x25 mm @ 1200 mm C/C. The 20 to 25 mm thick POP lath pastering over n. less than 0.56 mm thick wire gauge in complete ceiling incl form work. Ration of POP and wall putty (1:10) and applying two coats of oil bound distemper incl chalk whitening and priming in alkali restant incl preparing the surface complete all as specified and directed.

S&F POP false cornoces matching with existing POP false ceiling and wall putty (1:10) and applying two coats of oil bound distemper incl chalk whitening and priming in alkali restant incl preparing the surface complete all as specified and as directed.

Demolition of cement concrete (unreinforced ) in above ground floors exc 15 cm thickness complete all as specified and directed.

M & L 25mm thick PCC 1:2:4 type B-0 using 20 mm graded stone aggregate as in leveling course to floor complete all as specified and directed.

M&L 75mm thick for PCC 1:3:6 type C-1 as in plinth protection/floor complete all as specified and directed

M & L non-skid Heavy duty endura tile 400x400x25 mm thick coloured joint free in floors etc set and jointed in neat cement slurry and pointed in coloured cement to match over and including 15 mm thick screed in cement mortar 1:4 complete all as specified and directed.(Make :Johnson Endura/ Somany or equavalent)

Excavating over areas, n.exc.1.5m deep and in any type of soil and getting out complete all as specified.

Removing excavated material exc. 250 m but n. exc. 500 m and depositing where directed complete all as specified and directed. .

Mild steel work as post and strut in fencing including cutting tops to shape as directed drilling holes, notching for wire etc Flat iron strip for securing chain link fencing with angle iron post etc including all necessary drilling, bolting or riveting etc. conforming to Fe-290 complete all as specified and directed. Note :- Excavation in post holes, PCC & chain link fencing shall be measured and paid for separately under respective items of this schedule.

Supply only 3.15 mm dia GI wire 50 X 50 mm mesh (chain link fencing) made up to mattresses or cages lapped wired and laid in position including closing and tied with angle iron properly complete all as directed. Note :- (i) Angle iron post, fillet and bolts for fixing chain link shall be measured and paid for separately under repective item of this schedule. (ii) Weight of chain link fencing shall not be less than 2.93 Kg per square metre.

Fixing only chain link fencing including line wires, any mesh, size and type to any type of standard, rails, straining bolts etc including provn of binding wire complete all as specified and directed.

S&F for aluminium composit panel 3.00 mm thick of required shape and size including all necessary fittings and frame work made of MS GI angle, Tee, screws etc as per manufactures instruction joints with silica gel complete all as specified and directed.

Supply & fixing of PVC wall panelling in double layer sheet for panel & inner framework. The strips should have in their centre a grave of 6mm & 1mm depth for sinking the head of the screw used to fix the strips to the wall vertically at an equal interval between two PVC strip. The PVC strips shall be fixed to the wall using steel screws through the groove in the PVC strip by using PVC fasteners panels are joined through solvent content. Wall panelling S Side prelam sheet complete all as specified and directed. Make : DECO India Cat Part No. - 0039.

S&F 19 mm dia stainless steel dropery rods in any colour fancy type complete all as specified and directed. Make : Vista Cat Part No. SW-06.

S&F in repair curtain brackets mild steel with matching with the curtain complete all as specified and directed. Make : Vista Cat Part No. SW-06.

S&F venation blind vertical type or plain decorated type level or ultima 100mm width of strip with necessary pulling threads aluminium channel along with all arrangement tixed to wall completed all as specified and directed.(Make vista)

S&F PVC/sunmica colour wall papers self adhesive wood grain wallpaper for wooden door/wooden cup board matching with existing with wall paneling shed complete all as specified and directed.

Surface excavation not exceeding 30cm deep & averaging 15cm deep & getting out in soft/loose soil complete all as specified and directed.

M&L sand filling under floors or in foundations including watering and consolidation complete all as specified and directed.

M&L for machine pressed precast concrete interlocking paver block of prepolished, coloured, any shape and size confirming to IS-15658-2006 of 80mm thickness, M-40 grade laid over complete all as specified and directed.

Excavation in trenches, n.exc 1.5m wide & n.exc 1.5m depth & getting out complete all as specified and directed.

M&L PCC 1:3:6 type C-1 using 20mm graded stone aggregate for surfaces channels, bed of drains including forms/moulds etc complete all as specified and directed.

Extra for forming fair finished to drain or channel inner girth in cement concrete including forms, mould, etc complete all as specified and directed. (inner girth only to be measured as specified).

Add or deduct for each 25mm girth or part there of over or under 30cm ditto. complete all as specified and directed.

Use and waste of form work to sides of concrete foundation, footings, bases column, raft and raft beams, plinth beams etc. rough finished surface of concrete complete all as specified and directed.

Use and waste of form work to sides of pillers, posts, piers and column etc rough finished surface of concrete complete all as specified and directed.

Use and waste of form work to sides and soffits of floor or roof beam, beam haunchings, girders, lintels, cantilevers, shelves including supportsetc for rough finished surface complete all as specified and directed.

M&L, 10 mm dia and over High strengh deformed bars ( TMT bars) cut to length ,bent to shape required including cranking bending, binding with annealed wire not less than 0.90mm complete all as specified and directed.

Description all as item No 75.00 above but 8 mm dia as in stirups and spacers.

M&L RCC M-25 (Design mix) as in foundations including raft,footings ,foundation beams, plinth beams, bases of columns etc and mass concrete all as specified and directed.

M&L RCC M-25 (Design mix) as in coloumn ,pillars, piers, post and strut complete all as specified and directed.

M&L RCC M-25 (Design mix) as in Beams complete all as specified and directed.

M&L rendering 15mm thick in cm 1:4 on other than fair surface of brick or concrete wall surfaces finished even and smooth without using extra cement complete all as specified and directed.

S&F for mild steel framed braket of angles of 50 x 50 x 6 mm size or tees with web and flanges cut to shape, conforming to Fe 290, Gde-E-165 complete all as specified and directed.

S&F galvenised 2 strands,steel barbed wire with 2.24 mm dia barbed with 2mm dia barbs at 75 mm spacing and straining and fixing to any type of standared rails bolts, including securing or tying st crossing with and provision of galvanised mild steel wire,staples or steel pins etc,complete all as specified and as directed. NOTE:- Each line of wire to be measured.

M&L for providing precast cement concrete louvres and jallies,40mm thick (measured solid) with cement concrete 1:2:4 type B-0 using 12.5 mm graded stone agg, including all mouldings set in CM 1:4 complete all as specified.

Material and labour for treating small articles of steel like MS steps etc with coal tar/black paint including preparation of surface, area tarred not exceeding 0.1 Sqm, complete all as specified and directed.

M&L mild steel framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing complete of grade Fe-290 (Gde E-165)

S&F 75mm bore PVC (SWR) pipe single socket in any lenth with rubber ring joints fixed in walls as in weep holes complete

Note :- Credit shown in credit schedule of tender document shall be considered by the tenderer while quoting the rates of various items. The same shall be recovered from various payment to contractor before handing over old material.

R K CONSTRUCTION COMPANY

Toshi Enterprises

chauhan construction

VIPUL CONSTRUCTIONS

M/S SS Tarders

Mohit Enterprises

M/S Aquarius Construction