REPAIR MAINT OF EXTERNAL WATER SUPPLY SYS INCL REPAIRS TO VARIOUS PUMP SETS REPLACEMENT OF UNSV PIPE LINES VALVE CLEANING OF SUMPS WITH CONNECTED WORKS AT SHAKURBASTI AND HIRANKUDNA UNDER GE NORTH DELHI CANTT 10

Amount

Excavation in trenches not exceeding 1.5 mtr depth width and not exceeding 1.5m depth for laying pipes or for other work in loose/soft soil complete

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exceeding 25cm complete

Removal of surplus soil obtained from excavated material not exceeding 50 mtr and depositing where directed at a level not exceeding 1.5 mtr above the starting point complete

Taking up existing CI/ DI Pipe water mains incl fittings and relaying, jointing and testing of same in to trenches in position after cleaning and removal of scale/blockage complete for the following sizes (Note - Lead joint shall be measured and paid separately) :-

(a) 80mm bore

(b) 100 mm bore

Supply, laying, jointing and testing of DI Pipe with spigot & socketed end, centrifugally cast, Class LA, push on joint including jointing material laid in trenches in old/ new route as required at site including taking down the old/ unsv pipe line complete all as specified & directed of following sizes (Make - Electrosteel / Jindal / Kesoram / IISCO / Electrotherm / Tata) (Note : Excavation and earth work shall be measured and paid separately under respective items of schedule) :-

(a) 80 mm dia

(b) 100 mm dia

(c) 150mm dia

M&L for CI/DI fittings, ISI marked, bends (any type, radius & angle) tapers any type (straight, bend, increasing decreasing or double socket etc) tee piees, single branch, 'Y' junction, double branch cross (socket & spigot or flanged) collars, caps & plugs for spigot socketed pipes upto 150 mm bore complete

M&L for run lead joint incl jointing material for CI/DI pipe for following sizes including burning & removing old lead joint complete :-

(a) 80mm dia

(b) 100mm dia

(c) 150mm dia

M&L for CI Sluice Valve of pressure class PN-1.6 type flanged and drilled at both ends, conferming to ISI mark and having gun metal spindle and rings including wheel for operating all as specified including two numbers flanged socket and jointing materials such as bolts, nuts, washers, rubbers/ fibre board gasket including taking down old unserviceable valve from pipe line of both ends complete of following sizes

(a) 80 mm dia

(b) 100 mm dia

(c) 150 mm dia

Cutting of existing CI / DI pipe for insertion of CI specials /valves etc. all as required including dewatering of leakage water etc complete for the following sizes :-

(a) 80mm dia

(b) 100mm dia

(c) 150mm dia

Refixing/ Relaying only GI pipe in position with all new fittings after cleaning and removal of scale/blockages effectively incl taking out from trenches complete all as specified and directed for following sizes (Note : Excavation and earth work shall be measured and paid separately under respective items of schedule) :-

(a) 15 mm bore

(b) 20 mm bore

(c) 25 mm bore

(d) 40 mm bore

(e) 50 mm bore

(f) 80 mm bore

Supply, laying, jointing & testing of GI Pipe, medium grade, including all fittings in old/new position, laid in trenches/ wall including taking down the old/unsv pipe line complete all as specified & directed of following sizes (Note : Excavation and earth work shall be measured and paid separately under respective items of schedule) :-

(a) 80 mm dia

(b) 50 mm dia

(c ) 40 mm dia

(d) 25 mm dia

(e) 20 mm dia

(f) 15 mm dia

Drilling and tapping cast iron water mains (in position) for branch connections of 15 mm bore to 25 mm bore including necessary fittings and mild steel brackets rubber gasket, brass ferrule etc complete

S&F in repair heavy duty flanged GI pipe 100 mm bore including GI flanged bend with nut bolt, washer and gasket complete

M&L for construction of brick masonary valve pit chamber including necessary excavation and earthwork, PCC (1:4:8), brick work in CM (1:6) with 12 mm thick rendering in cement mortar 1:4 on internal surface of valve pit and mild steel sheet cover 3mm thick and mild steel angle iorn frame size 40 x 40 x 5 mm around of valve pit, locking arrangement with pad lock of size 50 mm brass, 6 leavers and key (Make : Godrej) complete including two coat of synthetic enamel over a coat red oxide primer on steel surface with preparation of surface and including dismantling of existing valve pit complete all as specified & directed for following sizes (internal dimension) :-

(a) Size 600 mm X 600 mm X 600 mm

(b) Size 900 mm X 900 mm X 900 mm

(c) Size 1200 mm X 1200 mm X 900 mm

Supply, installation and commissioning LT panel cubical type, wall mounted, indoor, fabricated out of CRCA sheet 2mm thick, door handles locking arrangement suitably spaced, totally enclosed in chamber for reception of 3 phase, 440 V, 50 HZ, AC supply including all connection with aluminum strips, internal wiring with suitable size (minimum 1.5 sqmm) of PVC copper conductor wire with lugs. Panel shall be effectively PVC gasketed and sealed, glands to be provided at cable entries, powder coated painting complete all as specified & directed and comprising of following as under :- (a) 4 Nos bus bars of high conductivity aluminium alloy, 3 Nos for phase (R,Y,B) rating 200 amp rating and 1 No for neutral rating 100 amp, mounted on DMC support with heat shrink sleeve - 01 set. (b) MCCB 4 pole, 100 amp, 415 volts, 25 KA - 01 No ( Incoming) (c) MCCB 4 pole, 63 amp, 415 volts, 25 KA - 02 Nos ( Outging) (d) Auto Phase Sequence corrector 100 amps, 415 Volt - 01 No (e) Power contactor of DOL Starter suitable upto 7.5 HP single phase alongwith motor protection/circuit breaker - 02 Sets (f) Voltmeter (0-500V) digital type -01 No (g) Ammeter (0-200 amps) digital type with CT's - 01 No (h) Indication lamp (R,Y,B), LED type - One set of three

M&L for preparing the surfaces of wall of pump house/OH/UG sumps of size 600x450 mm and applying one coat of synthetic enamel paint (bule/Black) and written on it in white paint as 'Date of cleaning, Due date of cleaning, capacity of pump etc of letter not less than 35 mm height complete all as direceted

M&L for painting of existing Steel/RCC surface with one coat of Black/Blue colour synthetic enamelled paint including preparation of surfaces complete

M&L for writing letters or figures (Block, Roman, Italic or Indian) n exc. 30 cm high with synthetic enamel paint on existing steel/ RCC wall surface with synthetic enamelled paint complete

S&F in repair heavy duty Brass forged Ball valve, screwed down high pressure 25 Kg/Cm2 with iron handle, screwed both ends complete for the following sizes of pipes :-

(a) 50 mm dia

(b) 40 mm dia

(c ) 25 mm dia

(d) 20 mm dia

(e) 15 mm dia

S&F in repair direct on line starter 415 volt, 50 Hz with voltmeter, Ammeter, relay, timer and single phase preventor complete for following pump set capacity :-

(a) 3 HP Pump Set

(b) 7.5 HP Pump Set

S&F in repair CI non return valve, heavy duty, 100 mm dia, class PN-1.6 flanged end complete (Make : Leader/ BIR/ Kirloskar/ Upadhaya/ Zoloto)

Suppy only liquid chlorine suitable for water treatment by mannual methed HDPF in 50 litre drum (ISI marked and approved make of E-in-C's Branch) (Note :- Fresh lot of liquid chlorine shall be supplied with in 45 Days from the date of manufacturing as per monthy demand or as directed

Supply only bleaching powder Calcium Hypochloride minimum 32% cholorine as per IS-1065:1989 in 25 Kg Bag (ISI marked and approved make of E-in-C Branch) (Note :- Fresh lot of bleaching powder shall be supplied with in 45 Days from date of manufacturing as per monthy demand or as directed)

S&F in repair battery brass terminal heavy duty

S&F in repair battery lead of copper conductor cable 50 sqmm X 1 mtr with lugs

S&F maintenance free Lead Acid battery, 12 Volt of following capacity :-

(a) 100 AH, 17 Plates

(b) 150 AH, 23 Plates

(a) 180 AH, 25 Plates

M&L for replacement of industrial copper conductor submersible cable, PVC insulated and PVC sheathed cable, 1100 volt grade of size 4 sqmm x 3 core including submersible cable connection complete.

Taking up submersible pump set upto 7.5 HP with MS column pipe from borewell and lowering the same after repairing with electric connection including replacement of unserviceable nut, bolt, washers and gasket etc complete all as directed

M&L for replacement of heavy duty MS column pipe, 50 mm dia, 3 m long flanged welded complete

Cleaning of underground/semi underground sump by taking out all sludge, silt from bottom and cleaning all inside walls with wire brush and brooming the walls and top ceiling/roof including washing the walls with fresh water mixed with bleaching powder and draining out complete sludge, silt etc from bottom of the sump and applying one coat of lime wash for the UG sump of capacity 50,000 gallons complete all as directed

All as per item No. 30 above but for the UG sump capacity 25,000 gallons

Cleaning of RCC OH tank, by taking out all sludge, silt from bottom and cleaning all side walls with wire brush and brooming the walls and ceiling/roof including washing the walls with fresh water with bleaching powder and draining out complete sludge, silt etc from bottom of the tank and applying one coat of lime wash inside complete for walls and roof/ceiling of 12 mtr approx staging for the following capacity :-

(a) 1,00,000 gallons

(b) 50,000 gallons

S&F in repair CI pipe 150mm dia class 'B', ISI marked centrifugally cast plain end and cut to required length, fixed in existing water pumping /Hydrant line complete (Note :- Lead joint and CI specials shall be measured and paid separetely)

S&F in repair of heavy duty stainless steel fore headed hydrant valve double headed of size 63 mm dia including nut, bolt complete

S&F in repair Water level indicator for OH Tank consisting of the following complete all as directed (Make : Recktronic Devices & system/ Universal switch Gear Contol) :- (a) Water level indicator of five level indication for overhead tanks inclusive of five rust proof, maintenance free, magnetic control float switch sensor and panel showing level indications including necessary Cable (Approx 30 RM) for sensor power supply to the panel (b) S&F of new copper float ball of 300 mm and MS pointer connected with SWR ropes through brass pully fixed on angle iron support with necessary fabrication and welding work so as to slide and indicate the water level in the sump .

S&F in repair functional conventional type water level indicator for UG sump consisting of the following complete all as specified & directed :- (a) Water lavel indicator height (as per sump/tank depth) up to 6mtrs, 150mm width fabricated out of 3 mm thick MS sheet and angle iron frame of 40mm x 40mmx3mm duly painted with two coats of synthetic enamel paint of approved shade over a coat of red oxide primer and marking the letters in white glossy paint and suitable size of letters / Number is not less than 5". (b) S&F of new copper float ball of 300 mm and MS pointer connected with SWR ropes through brass pully fixed on angle iron support with necessary fabrication and welding work so as to slide and indicate the water level in the sump .

M&L in repair for three layer PPR (Poly propylene random) copolymer 32 mm dia concealed pipe SDR 7.4 (PN 16) UV stabilized and antimicrobial fusion welded having thermal stability for hot and cold RO water supply with PPR plain (Brass threaded) fittings laid in trenches..

M&L in repair heavy duty PPR gate valve (Brass insert) ISI marked for 32mm dia PP-R pipe

Taking up & shifting carefully DG set 160 KVA, 3 phase 4 wire from electric sub-station to main pump house (Distance apprx 600 mtr) and installation of the same at new foundation incl all necessary connection complete all as directed (Note- Civil work for the foundation will be measured and paid separately)

M&L for PCC 1:4:8 (Type D-2 ) with 40 mm graded stone for path/floor/foundation of DG set as directed complete

M&L for RCC (1:2:4 ) Type B-2 in 20 mm graded stone for plateform of DG set/ pump set complete (Note- TMT bar will be measured & paid seperately)

M&L for servicing DG set, 3 phase, 160 KVA of make Greaves cotton with replacing the air filters, diesel filter, super by pass filter,oil filter,coolant and lubricating oil and servicing & cleaning of radiator incl testing after repair & servicing complete all as specified and directed

M&L for replacing of following defective parts of DG set 160 KVA, 3 Phase 4 wire of Make- Cotton Greaves :- (a) Piston-01 (b) Liner sleeve -06 (c) Piston ring- 06 set (d) Liner 'O' ring-06 set (e) Packing kit-01 set (f) Head gasket-06 (g) Hose pipe set with clamp-01 set (h) Stop sonolight--01 set (i) CR bearing-06 pair (j) Head 'O' ring set-06 set (k) Head valve-06 pair (l) Radiator new jali-01 set (m) canopy repairing with material, perforated type aluminium sheet MS sheet glass wool (approx 04 Sqmtr) - 01 Job (n) Head repairing lathe charge-06 Job (o) Pump nozzle repair-01 set (p) Cartage charge- 01 Job (q) Labour charge -01 Job

M&L for earthing with Galvanised Steel earth plate electrode 60cm x 60cm x 6mm thick buried directly in ground vertically at a depth not less than 2.25metre below normal ground level with top edge of earth plate at a depth not less than 1.5 metre below normal ground level, earth plate surrounded from all sides by 15cm thick packed layer of charcoal dust and common salt filling in alternate layers and electrode connections by using Galvanised Iron strip of size 32 x 6 mm as earthing lead (upto the body of the equipment) by means of bolts, nuts, check nuts and washers made of galvanised iron and thimbles and protected by light grade 40mm dia GI pipe connected to main switch board or main control board and GI pipe medium grade 20mm bore for watering and including funnel, wire mesh, RCC pit cover and PCC chamber pit with PCC (1:3:6) type C-2 using 40mm graded stone aggregate, including excavation and earth work in any type of soil complete all as specified and shown in electrical plate No 5 of SSR 1991(Part-I) complete all as specified and directed

Supply & installation in repair of Sewage submersible pump of capacity 0.75 KW/1 HP, single phase, 230 volt, 2800/2900 RPM including all connection and testing complete all as specified & directed

Supply, lowering, testing and commissioning of submersible pump set in stainless steel body, single phase, 3 HP, 50 Hz, head range 12-37 mtr, outlet 50/65 mm complete all as specified and directed.

Supply, installation, testing & commissioning LT distribution cubical panel outdoor type, double door with rigid hinges, door handle locking arrangement back side openable, compartmentalized design, mounted on suitable PCC blocks, fabricated out of CRCA sheet 3mm thick, suitably spaced, totally enclosed in chamber for reception of 3 phase, 440 volt, 50 HZ, AC supply including all connection with aluminium strips, internal wiring with suitable size of PVC copper conductor wire with lugs panel shall be effectively PVC gasketed and sealed, glands to be provided at cable entries, powder coated painting and sign writing for in/out going connections and bottom support by MS channel MC-75 grouting in PCC 1:2:4, height 450 mm from ground level complete all as specified and directed and comprising of following :- (a) 4 Nos bus bars of high conductivity aluminium alloy, 3 Nos for phase (R,Y,B) rating 300 amp rating and 1 No for neutral rating 150 amp, mounted on DMC support with heat shrink sleeve - 01 set. (b) MCCB 4 pole, 200 amp, 415 volts, 25 KA - 01 No (Incoming) (c) MCCB 4 pole, 160 amp, 415 volts, 25 KA - 01 No (Outging) (d) MCCB 4 pole, 63 amp, 415 volts, 25 KA - 02 Nos (Outging) (e) MCB SPN 40 amps, 240 Volt, 'C' series - 02 Nos (f) Indication lamp (R,Y,B), LED type - One set of three

All as per item No 47 above but comprising of following :- (a) 4 Nos bus bars of high conductivity aluminium alloy, 3 Nos for phase (R,Y,B) rating 200 amp rating and 1 No for neutral rating 100 amp, mounted on DMC support with heat shrink sleeve - 01 set (with 03 holes RYB & Neutral busbar) (b) MCCB 4 pole, 200 amp, 415 volts, 25 KA - 01 No (Incoming) (c) Indication lamp (R,Y,B), LED type - One set of three

M&L for replacement of cast iron impeller and steel shaft of centrifugal pump including dismantling, opening and refixing the same on its original location of following capacity :-

Dismantling of 7.5 HP pump set from rusted base frame and refixing the same on new base frame complete (Note : MS base frame will be measured & paid seperately)

M&L for replacement of MS channel base frame fabricated by MS channel (MC-100) including civil work and grouting the same in PCC (1:2:4) with existing size/ make suitable for 7.5 HP pump complete

S&F in repair of good quality tyre rubber coupling (No.TC/0/015-2913 DE) suitable for 40 HP / 30 HP pump set.

S &F in repair of good quality tyre rubber coupling (No. TC/P/014-2514-PX) suitable for 40 HP / 30 HP pump set.

S &F in repair of good quality tyre rubber coupling (No. TC/5/011-2004-GN) suitable for 7.5 HP pump set.

Dismanlting and disconnection electrical and water connection of the pump and transport to work shop & opening carefully and servicing complete with replacing of bushes, gland packing, ball bearing, rubber gasket, nut and bolt and re-fixing it in original position and making out all electrical and water connection incl painting to two coats with synthetic enamell paint after necessary prepartion incl testing & commissioning complete for following capacity :- (Note :- Replacement of impellor rewinding of motor shall be measured and paid separately)

M&L for rewinding of submersible motor with PVC insulated copper winding wire of existing gauge and size for following capacity. :-

M&L for rewinding of electrical motor, 3 phase with super enamelled copper winding wire/ PVC insulated copper winding wire of existing gauge and size to get proper speed and load with removing burnt winding wire for following capacity of motor :-

S&F battery charging alternator 12 Volt, for 30 KVA DG set complete

M&L for Servicing of DG set, 3 phase, 320 KVA capacity, 415 volt, 50 Hz of Make- Cummins with replacing the air filter, diesel filter, super by pass filter, lubricating filter, coolant, lubricating oil, fuel pipe with bengo bolt, hose pipe complete set and vent housing with clamp incl servicing and cleaning of radiator & diesel tank as per manufacturer instructions incl testing after repair & servicing complete all as specified and directed

S&F electronic battery charger, 24 Volt of DG set 320 KVA, 415 Volt, 50 Hz

M&L for Servicing of DG set, 3 phase, 400 KVA capacity, 415 volt, 50 Hz of Make- Greaves Cotton with replacing the air filter, diesel filter, super by pass filter, lubricating filter, coolant, lubricating oil, fuel pipe with bengo bolt, hose pipe complete set and vent housing with clamp incl servicing and cleaning of radiator & diesel tank as per manufacturer instructions incl testing after repair & servicing complete all as specified and directed

M&L for replacement of Electronic AMF Gen Set Controller Display Board (Model/Part No EMS 927V4/4083935) with digital card and programming complete for 400 KVA DG Set of make -Greavs/320 KVA DG set of make -Cummins including connection and testing complete all as directed

M&L for Servicing of DG set, 3 phase, 63 KVA capacity, 415 volt, 50 Hz of Make-Crompton Greaves /Mahindra & Mahindra with replacing the air filter, diesel filter, super by pass filter, lubricating filter, coolant, lubricating oil, fuel pipe with bengo bolt, hose pipe complete set and vent housing with clamp incl servicing and cleaning of radiator & alternator assembly & diesel tank as per manufacturer instructions incl testing after repair & servicing all as specified and directed

Dismantling & removing carefully engine & alternator assembly with all assesories complete of DG set 63 KVA capacity from base frame and refixing the same on new base frame including all necessary connections complete all as directed (Note- Base frame shall be measured & paid separately)

M&L for replacement of following spare parts of 63 KVA DG set, 415 volt of Make Mahindra & Mahindra :-

(a) Sound proof Accoustic Enclosure Canopy, water proof complete 3000x2200x2300 mm made out of 1.6mm thick CRC sheet with acoustic rock wool 96/m3 density and thickness 100mm to meet noise level less than 75 db in one meter distance including both side doors, hinges, opening for silencer as per manufacturer specification complete all as directed

(b) MS channel base frame 2500x2200mm fabricated by MC-150 channel including cutting in proper size, making hole & welding complete

(c) Solonoid switch,12 volt, pull-5 kg, stroke-30 mm (Make-Rico or equivalent)

(d) Automatic Voltage Regulator, 12 V (AX-440)

(e) Battery Charging Alternator, 12 Volt

M&L for replacement of feeding pump set, monoblock type, 1 HP, 240 Volt, 2800 RPM complete for 1000/700 LPD RO plant (Make- CRI/Siemens/Crompton/ABB/KSB)

S&F in repair motor relay suitable for high pressure pump 3 HP, 230 volt

S&F pump capacitor 50 MFD, 440 Volt (Make - Epcos/Usha/havells)

S&F pump capacitor 25 MFD, 440 Volt (Make - Epcos/Usha/havells)

M&L for black flexible rubber hose pipe 100 mm dia, ISI Marked

M&L for black flexible rubber hose pipe 50 mm dia, ISI Marked

M&L for stainless steel wire rope (ss-304) size 8 mm dia with 2 nos holding clamps suitable for hanging of sewage submersible pump complete all as directed

S&F in repair pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.5 mm thick of any colour having tensile strength of 550 MPa as in roof covering/cladding to wall, fixed with self tapping screws complete

M&L in repair steel work of tubular pipes (medium weight) including embedding in concrete and screwing etc posts and struts in fencing including cutting tops to shape as directed, drilling holes motching for wire etc flat iron fillets including all necessary drilling, bolting or riveting etc and similar work conforming to Fe-290 Gde E-165 complete all as specified and directed

S&F in repair chequered plate, angle iron, beam and channel sections of required size with flange plates caps, bases splices, angle brackets, cleats and other connections and conforming to Fe-410-W (Gde-E-250) quality 'A' including taking out old/damaged PCC cover complete

M&L for cutting of road/path (width-25 cm x 40 cm) for laying of pipe line and making good to disturbed road/path including provision of PCC 1:2:4 type B-1 using 20 mm graded stone aggregate all as specified

M&L for spray painting of complete water pumpset of cap 7.5 to 40 HP with two coats of synthetic enamelled paint of specified colour after preparation of surface

M&L for spray painting of accoustic enclosure canopy of DG set of capacity 320/400 KVA complete with two coats of synthetic enamelled paint of specified colour after preparation of surface complete

S&F in repair for ' Y' shape CI strainer flanged type to avoid foreign material to pass through meter suitable for following sizes incl cutting existing CI/DI pipe :-

(a) Size for 100 mm dia pipe

(b) Size for 200 mm dia pipe

S&F in repair Vibration Pad suitable for DG set any capacity as directed

M&L for rotating rectifier assembly plate with diodes,12 Volt, suitable for following capacity of DG Set :-

M&L for Servicing, descaling and tungsten welding of solar water heater of capacity upto 200 LPD complete all as directed

S&F in repair of solar water heating element, 3 KW, 230 Volt incl connection complete

S&F in repair evacuated glass tube with existing size of solar water heater of capacity upto 200 LPD

S&F in repair of stainless steel (SS -304) inner tank wall thickness not less than 0.7 mm of solar water heater 200 LPD complete

S&F in repair of outer tank wall thickness not less than 0.5 mm of solar water heater upto 200 LPD complete

M&L in replacement for rotational moulded tripple layer Polyethylne water storage tank cylindrical vertical with closed tap of capacity 5000 Ltr including inlet and outlet water connection complete all as directed.

All as per item No 88 above but of capacity 10000 Ltr

Supply only high range Chlorine Test Kit with coloured sample complete with all testing fitment and OT solution in plastic finish box complete (Make : Aquafit / Aquasol)

Supply only Total Hardness Test Kit (5-1000 Mg/L) with coloured sample with all testing fitment and OT solution in plastic finish box complete (Make : Aquafit / Aquasol)

M&L for painting of water supply pipes net works of 100 mm dia consisting of valves any type/ size at various pump houses inlcuding duly scrapping thoroughly the existing corroded paint / dirt/ dust / rust and preparing the surface and applying two coats of synthetic enamel paint over a coat of red oxide primer as per the colour code and marking the water flow directions on pipe lines as directed.

M&L in repair auxiliary contactor 415 Volt, 18/20 amps, coil voltage 230 Volt including auxiliary block (1 NO + 1 NC) and over load relay complete

S&F MCCB 4 Pole, 415 volt of following capacity on existing panel including removing old one complete :-

(a) 250 amps, 25 KA, adjustible type

(b) 200 amps, 25 KA, adjustible type

(c ) 125 Amps, 25 KA, with thermal magnetic relase

(d) 63 Amps, 16 KA, fixed type

S&F in repair LED Post top lantern luminaire with die cast aluminium spigot, lid cover and clear acrylic cover 40 watt, 5700 K with IP-65 protection incl connection complete (Make : Crompton cat Pt No LPTO-40-CDL or equivalent in Havells/Philips/Wipro)

S&F in repair LED flood/security light fitting of 30 watts with pressure die-cast aluminium housing complete with all accessories, fixing of fitting on wall with necessary fixing arrangement as required at site & connection complete (Make : Surya / Polycab / C&S)

Collecting water sample in clean bottle from borewell/ UG sump/service tank and getting Chemical, Boilogical, Potability Testing of water sample (as per IS 10500:2012) at Govt recognised/approved institute/Lab for potability and chemical analysis complete all as specified & directed

S&F LED Based Outdoor Weatherproof Aviation Obstruction Lighting Luminaire wiith Inbuilt AC-DC Converter 48V / 160 – 230 VAC Housed in Die-Cast Aluminium (LM 6) / Aviation Orange Finish Ultra Violet Stabilised Acrylic Lens for directing light Built in Photo Controller / Built in SS Bird Spike Solid State high flux Light Emitting Diode / Intensity: 32.5 Candelas Life: >50000 Hrs / Sealed with EPDM Gasket Power Supply: AC-DC Converter 48V / 160 – 230 VAC Standards: Confirms to ICAO Annex 14-6, FAA AC No. 70/7460-IG, Radio Interference: BS 800/EN 55014 Connections, necessary welding, clamping,mounting with 32mm dia GI pipe, 1.2 mtr height,1.5 sqmm copper wire with 20mm PVC conduit fixing on work portions upto nine storeys height bldg incl taking down unsv complete.

S&F in repairs for informatory/eqpt history/ installation sign board of size not less than 1200 x 900 mm rectangular type with 2mm thick MS sheet plain type made out of angle iron channels frame, back ground and epqt history with high intensity prismatic reflective tape as specified colours (blue and white) complete

M&L taking down cement plaster of any description from brick, stone walls or concrete surfaces including raking out joints, haking for key, scrubbing down with water and rendering 15mm thin cm (1:4) mixed with PD proof 101 LW(+) of Dr Fixit or equivalent integral WP admixer @ 200 ml/bag of cement over two coat of super latex 302 of DR Fixit or equivalent in the ratio 1:4:7 (one part super latex 302, 4 part water and 7 part cement) @ 1.50 Kg of extra cement complete sewage well, sump etc any type/size all as specified & directed (Note - Cost of PD proof 101 LW(+) and super latex 302 shall be deemed to be included in quoted rate)

M&L for MS TMT bar 10mm dia, cut to length, bent to shape as required incl cranking, bending with MS wire (annealed) not less than 0.9mm dia or securing with clips complete all as directed

Supply, lowering, testing and commissioning in repair of electric submersible pump set, stainless steel body three phase, capacity 3 HP suitable for flow rate 200 to 500 LPM, head 60 mtr complete all as specified & directed

All as per item above but pump capacity 1 HP, suitable for flow rate 30 to 100 LPM, head 60 Mtr

S&F in repair 3 pole power contactor, type MNX-32 with coil voltage 230 Volt incl connection complete

S&F in repair front mounting add-on auxiliary contact block with 1 NO+1 NC suitable for MNX contactor 32/40 amp

All as per item above but with 2 NO+2 NC

S&F in repair bolted fuse link type HG, 4 amp size F-1

S&F in repair heavy duty electric motor terminal block 70 amp, 415 Volt for 40 HP motor complete (Make-Elmex/Wago/Phoenix)

S&F in repair heavy duty electric panel mounted terminal block 40 amp, 2 row, 4 way complete

S&F in repair din type terminal block 16 amp, 2 row, 12 way complete

S&F heavy duty GI pipe 40mm bore with heavy duty GI socket and taking up old pipe alongwith submersible pump set of any capacity from borewell and lowering the same complete all as directed

Cleaning of sewage well/sump of size 3.50 mtr dia X 06 mtr depth, by taking out all sludge, silt from bottom and cleaning all inside walls with wire brush and brooming the walls and top ceiling/roof including washing the walls with fresh water mixed with bleaching powder and draining out complete sludge, silt etc from bottom of the sump and applying one coat of lime wash ar inside wall of sump complete all as directed (Note : All T&Ps shall be arranged by the contractor and cost of the same is deemed to be included in quoted rate)

All as per item No 111 above but for sewage well/sump of size 2.00 mtr dia X 06 mtr depth

M&L for PCC 1:2:4 (Type B-1) with 20 mm graded stone for roof, curves, mud stops, rounded, champhered edges, floor et complete

M&L for sand filling under floor or in foundations incl levelling, watering, consolidation complete as directed

M&L for machines pressed precast concrete interlocking paver block any shape/size confirming to IS : 15658-2006 of 60 mm thickness in M-35 grade complete

M&L for surface dressing not exc 15 cm deep in soft/ loose soil

Demolition of cement concrete (unreinforced) of any type incl removal of same from site & thrown out where directed

M&L for brick work with sub class 'B' bricks straight or curved on plane exc 6 mtr mean radius built in CM (1:4) incl demolition of old brick work incl removal & thrown out of same from site where directed

M&L for 15mm thick plaster in cement mortar 1:4 of fair face of brick work or concrete surface even & smooth, neeru finish incl taking down old cement plaster

M&L in repair of base frame for 40 HP pump set made out of MS channel MC 125 & mounting fabricated by MS channel MC 100 to match with existing frame in size & shape incl dismantling & taking down pump set and re-fixing the same on new base frame complete all as directed (Note : MS work will be paid measured & paid seperately)

S&F in repair of electronic timer ST 100 for starter of pump set complete

M&L for replacement of asbestos gland rope of required size for water pumps complete

S&F in repair of GI strip size 25X4mm thick incl shaddle, to be fixed on pillar/dome of OH tank as directed

Shiv Enterprises

D P ENTERPRISES

NEETU TRADERS (INDIA)