SPECIAL REPAIR TO BLDG NO P-71/2 AND P-72/3 AT GANDHI CHOWK SI LINES, BHOPAL

Amount

Taking down chowkhats or frames exc 1.50 Sqm but n.exc 4 Sqm with shutters (without taking off shutters from the frame)

Taking down chowkhats or frames n exc 1.50 Sqm with shutters (without taking off shutters from the frame)

Taking down shutters of any descripition exc 1sqm n exc 2sqm each and removing to or from store

Taking up or down 15mm bore steel tubing and connections, including cleaning for refixing or removal to store

Taking up or down 20mm bore steel tubing and connections, including cleaning for refixing or removal to store

M&L for Cutting chases, pinning in, making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring, etc., and making good, cutting not exc 10cm girth

S&F Tubes 15mm dia, 'Medium grade' galvanised, with all fitting and fixed complete to walls and ceilings or laid in floors

Supplying and laying of 20mm dia CPVC pipes SDR 11 and plain CPVC SDR 11 fittings in trenches complete all as specified

S&F Tubes 20 mm dia, `Medium grade' galvanised, with all fitting and fixed complete to walls and ceilings or laid in floors

M&L for Endura joint free colour tiles 8 to 10 mm thick (square/rectangular) area of each tiles not exceeding 0.11 sqm , in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match shade of tiles. Make: Johnson endura or equivalent make as approved by the GE.

Ditto all as per item No 10.00 above but on vertical surface.

M&L for vitrified tiles 10 mm thick light shades (square/ rectangular) polished, area of each tiles exceeding, 0.36 sqm, but n exc 0.42 Sqm in floors etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles.

Ditto all as per item No 12.00 above but on vertical surface over 10mm thick cement plaster with cement mortar (1:4).

M&L for Non skid Ceramic coloured tiles 7-8 mm thick (square / rectangular) area of each tile exc 0.11 sqm but not exc 0.18 sqm, in floor etc set and jointed in white or colour cement to match the shade of the tile complete all as specified and directed by Engr in charge.

M&L for glazed ceramic coloured tiles in vertical surfaces 350x250x7mm/ 450x350x7mm thick set and jointed in neat cement slurry and pointed in white or coloured cement to match shade of tiles.

Roughening surface of old cement floor by picking, sweeping clean and washing down with water to remove dust, etc

Demolition of flag stone slabs and tiles of any description or thickness in floors, aprons etc laid bedded and pointed in any mortar.

M&L for Granite (of any type) tiles 20mm thick machine cut, bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including cutting and polishing.

M&L for 20mm thick Granite (of any type) tiles machine cut in skirting/ dado laid over cement screed and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including cutting and polishing.

M&L for Screed bed or bedding layer of mortar 15 mm thick for laying floor finish in CM 1:4.

Fixing only tiles of any type over existing floor finishes (any type) with approved tile fixture adhesive as directed by Eng-in-charge

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises.

M&L for making good under cills and over archs, lintels and bressummers including all pinning where necessary in cement mortar (1:6) all as specified and directed.

S&F powder coated aluminium frame for doors, windows, ventilators with one or more rebates including joining cleat, channel etc for fixing, complete all as specified and directed. Note: Weight shall be verified by the GE.

S&F 4.8 mm thick plain sheet glass ordinary quality nexc 0.50 Sqm in each pane all as specified and directed.

S&F in repair Stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples

S&F Stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples

S&F 100mm size butt hinges medium weight cold rolled mild steel.

Ditto all as per item no 28.00 herein before, but 75mm long.

S&F 100mm butt hinges, extruded aluminium alloy with galvanised mild steel hinge pin, anodised and fixed, type C-21

S&F 150 mm long aluminium handles, cast type, anodised fixed to shutters complete all as specified and directed by Engr in charge.

Ditto all as per item no 31.00 herein before but 100 mm long

S&F 150 mm long aluminium anodised, barrel tower bolts of extruded section and fixed complete all as specified and directed by Engr in charge.

Ditto all as per item no 33.00 herein before but 100 mm long

S&F IInd class HW factory made 35 mm Glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc. (without sash bars), edge of framing plain, chamfered or rounded, fitted with cut and mitred beds for securing glass, etc.; sizes of members of shutters as specified in SSR Part I, Section 8. clause 8.20 (a); supplied and fitted to chowkhats.

S&F IInd class HW factory made 35 mm thick plain framed, panelled shutter (any number of panels) with panels of timber flat on both sides (feather edged), or of veneered particle board medium density, wood particle board with commercial face veneers fitted to chowkhats complete all as specified and directed.

M&L for Preparation new wooden surface of any description and applying two coats of synthetic enamel paint over a coat of pink primer all as specified and directed.

M&L for Preparation old wooden surface of any description and applying one coat of synthetic enamel paint all as specified and directed.

S&F 300mm Mild steel sliding door bolts, plate type, stove enamelled black, with bright bolt not less than 12mm dia with and including a minimum of 6 bolts and nuts, four on bolt plate and two on staple plate and fixed complete all as specified and directed.

S&F anodised aluminium fabricated grill for windows, vintilators complete fixing all as specified and directed by Engr-in-Charge

S&F 15 mm wash basin mixutre, centre hole, mixing hot & cold water, fancy type, cast copper alloy, chromimum plated with capstan head, chromium plated, screwed down high pressure, screwed for iron pipe etc and fixed in repairs complete all as specfied and directed by engr in charge. Make: Jaquar (Cat No: 5001B ) or equivalent make as approved by the GE.

S&F in repair Soap dish holder Make: Jaquar Cat No 1131N or equivalent make as approved by the GE.

S&F Towel ring Make: Jaquar Cat No 1121N or equivalent make as approved by the GE.

S&F 15 mm bib cock two way with flange, cast copper alloy, fancy type, chromium plated screwed down for iron pipe and fixed in repairs complete all as specified and directed by engr in charge. Make: Jaquar (Cat No: 5041 ) or equivalent make as approved by the GE.

S&F handshower (Health faucet) with 8mm dia 1 meter long flexible tube and wall hook fixed in repairs Make: Jaquar (Cat No- 573) or equivalent make as approved by the GE.

S&F chromium plated grating doom 100 mm dia with waste hole.

S&F in repairs PVC low level flushing cistern of 10 Litres with all internal fittings incl flush pipe and fixing to supply pipe

S&F PVC connection 15mm size with PTMT nuts of length 450 mm fixing complete all as specified and directed by engr in charge.

S&F in repairs 15 mm stop cock cast copper alloy, screwed down high pressure chromium plated screwed both ends for iron pipe or for unions and fixed complete all as specified and directed

S&F in repairs 15 mm bib taps cast copper alloy, screwed down high pressure chromium plated screwed for iron pipe and fixed complete all as specified and directed.

S&F tubular towel rail chromium plated 20 mm dia D type 60 cm long between flanges complete all as specified and directed by engr in charge.

S&F Solid PVC Door frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with MS square tube, as specified and directed.

S&F Factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of MS tube for top & bottom rails. MS frame shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for styles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the MS frame wlded/ sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, fixing tin the frame at site as specified and directed.

M&L PVC (SWR) floor trap plain with grating incl jointing with solvent cement 75mm bore complete all as specified and direcetd.

Taking down eaves gutters and rain water pipes (any size or pattern), including all fittings, heads, shoes, bends, swan-necks, etc., including cleaning or refixing or removal to Store (measured overall as fixed along the centre line over fitting and accessories)

S&F PVC(SWR) pipes 75 mm bore single socketed in any length with rubber rings joints laid in trenches

Ditto all as per item No 56 above but 110mm bore.

S&F PVC (SWR) bend of bore size 75 mm

S&F PVC (SWR) bend of bore size 110 mm

S&F PVC (SWR) branch piece single (Y) equal or unequal bend the following bore 75 mm.

S&F PVC (SWR) branch piece single (Y) equal or unequal bend the following bore 110 mm.

S&F PVC (SWR) junction single (single 'T') equal or unequal of the following bore 75 mm

S&F PVC (SWR) junction single (single 'T') equal or unequal of the following bore 110 mm

S&F PVC (SWR) vent cowl for following bore 75mm

S&F PVC (SWR) vent cowl for following bore 110mm

S&F 400mm x 350mm mirror with PVC cabinet including all fittings as accessories all as specified and directed. Make: Commander/ Prayag or equivalent as approved by the GE.

S&F in repairs Stainless steel sink, 1.00 mm thick for kitchen, with plug, washers and waste coupling, including bedding in cement mortar on to dwarf wall or including fixing cantilever brackets and connecting union to pipe, overall size 495mm x 420mm with bowl size 410mmx 330mmx 160mm fixed complete all as specified and directed.

S&F in repairs Plastic water closet seat cover, any colour, closed pattern with flat bottom, and mild steel chromium plated for aluminised hinging device complete.

S&F Brass CP mixer for mixing hot & cold water screwed down for iron pipe and fixed

S&F in repair of vitreous China wash down water closet pan (pedestal pattern), white (excluding fixing bolts, flushing cistern and flush pipe)

S&F Chromium plated shower roses with or without swivel joints, any size, including fixing to steel pipe or union

S& F in repair to CP fancy type Bib taps, cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed

S&F Glass Corner, size nexc 250mm with CP bracket.

S&F Sheet glass shelf assembly consisting of 5.5 mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60cm long

S&F Towel Ring of PTMT fixed with and including Chromium plated brass screws and wooden/ plastic cleats (Minimum weight 90 gms)

S&F Toilet paper holder, vitreous China, box type

S&F Jet Spray with connecting pieces including all necessary fittings and accessories as directed by Engr in Charge

S&F in repair looking mirror approved quality with wooden back and edge, complete polishing , fixing in repairs complete all as specified and directed.

S&F Pillar taps, cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered `Hot' or `Cold' with long screwed shanks and fly-nuts, screwed for iron pipe and fixed but fancy type 15 mm in dia in repairs.

S&F Angle Cock, cast copper alloy screwed pressure, with crutch of butterfly handle, screwed both ends for iron pipe for unions and fixed but fancy type ,15 mm in dia.

Dismantling water tanks and removing to store 500 to 1000 litres capacity

S&F 1000 ltrs capacity Rotational moulded polyethylene water storage tanks (Cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part-I

M&L for 2nd Class hardwood, Plain fillets, square, rectangular or triangular in section, clean sawn, secured with mills or brads, not exceeding 3 Sq.cm sectional area

M&L for prelaminated particle board 9 mm thick, exterior grade, prelaminated both side with decorative choice lamination fixed with nails to aluminium framed work fixed in repair.

M&L for prelaminated partcle board 19 mm thick, exterior grade, prelaminated both side with decorative choice lamination fixed with nails to aluminium framed work fixed in repair.

S&F magnetic catches for cupboards with plastic body and striking plate not less than 40mm including letting in and fixed complete all as specified and directed

S&F 75mm brass handle, cast type, polished bright complete all as specified and directed by Engr-in-Charge

S&F 40mm wide of flap continuous (piano) hinges, brass , bright finish

M&L 15 mm thick rendering in cm 1:4 on fair aces of bricks walls surface finished even and smooth without using extra cement including water proofing compound all as specified and directed. Note: water proofing compound shall be measured and paid seperately.

M&L for 15mm thick rendering in CM 1:6 on fair face of brick walls/ concrete surfaces finished even and smooth without using extra cement all as specified and directed.

Integral water profing compound

Taking down cement plaster, terrazzo/ cement dado, skirting etc of any description on brick/ stone walls, concrete surfaces etc including raking out joints, hacking for key, scrubbing down with water etc

M&L for Preparation of new plastered surface and applying two coats of oil emulsion distemper over one coat of white cement based putty all as specified and directed. Note: Thickness of putty shall be as per manufacturer's instructions.

M&L for Preparation of new plastered surface of wall and applying two coats of exterior weather proof water base emulsion paint over and incl a coat white cement based putty, complete all as specified and directed by the Engineer-in-charge. Make : Shalimar (Shaktiman)/ Asian (Apex) /Burger (Wall Masta) or equivalent as approved by GE. Note 1:- Exterior Acrylic Emulsion Paint should be carried out by any of approved company / firm (Apex of M/s Asian Paint or equivalent) Note 2: Thickness of putty shall be as per manufacturer's instructions.

M&L for complete removal of existing treatment and applying two coat of Exterior weather proof water base emulsion paint over & incl a coat of white cement based putty complete all as specified and directed Make : Shalimar (Shaktiman)/ Asian (Apex) /Burger (Wall Masta) or equivalent as approved by GE. Note 1:- Exterior Acrylic Emulsion Paint should be carried out by any of approved company / firm (Apex of M/s Asian Paint or equivalent) Note 2: Thickness of putty shall be as per manufacturer's instructions.

M&L for complete removal existing treatment and applying two coats of oil emulsion distemper over one coat of white cement based putty all as specified and directed. Note: Thickness of putty shall be as per manufacturer's instructions.

M&L for 3mm thick wall care putty on wall/ ceiling as specified and directed. Note: Thickness of putty shall be as per manufacturer's instructions.

M&L for PCC 1:3:6 type C-2 75 mm thick (using 40mm graded crushed stone aggregate) as in plinth protection

Demolition of concrete in ground floors and pavings (un-reinforced) nexc 15 cm thickness (below or above ground level).

Demolition of brick work or stone masonary built in cement mortar

M&L for Brick work with sub class 'B' bricks, straight or curved on plan to any radius in half brick thick walls built in CM 1:4 using modular bricks all as specified and directed

M&L for brick work with sub class modular 'B' bricks in cm 1:6 using modular bricks straight or curved on plan to any radius.

S&F in repair 20mm dia draphary rod decorative type incl brackets of approved quality as in complete, all as specified and directed

M&L for two coat of varnishing to new surface of any description, nexc 10cm in width or girth.

Dismantling of Asbestos cement (corrugated type, semi corrugated, etc.) sheets in roof coverings

Dismantling timber fillets, rails, posts, rafters, purlins, etc. under 40 Sq.cm in section in framed work.

Dismantling timber scantling 40 sqcm and over in section, in any position in unframed work.

S&F MS rolled section/ tubular sections in purlin , cross, beam, rafter, posts etc. incl connected cleats, hold fasts etc of grade conforming to Fe 410-O or Fe 310-O all as specified and direcetd. Note: Weight shall be verified by the GE.

S&F MS wind ties for roof truss including necessary drilling bolting as riveting etc and similar work to FE 410-S or FE 310-S all as specified and direcetd.

S&F pre-painted galvalume aluminium zinc coating GI based corrrugated steel sheet 0.50 mm thick of any color having tensile strength of 550 Mpa as in roof covering /cladding to wall fixed with self-tapping screws on angle iron frame of each side as directed by Engr-in-Charge.

Ditto all as per item No. 110 above but plain sheet.

M&L preparation of old painted surfaces of steel and iron surface of any description and applying two coats of synthetic enamel paint complete as specified and directed.

M&L for preparation of new steel surface of any description and applying two coat of synthetic enamel paint over a coat of red oxide primer all as specified and directed

S&F Framed work such as grills, gratings etc., with ends of bars shouldered and/or riveted, or forget into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe 410-0 or Fe 310-0

Dismantling structural steel work including doors, gates but excluding framed truss etc.

S&F Cutting chases, pinning in, making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring, etc., and making good, cutting not exc 10cm girth

M&L for machine pressed precast concrete inter locking paver block (Reflective type) in any shape and size confirming to IS-15658-2006 of 60 mm thickness M-35 grade with grey cement and pigment as specified and directed.

S&F in repair stainless steel plate rack complete assembeled set of (Size: 31 x 36 x 10 inch) fixed with screws as specified and directed

S&F in repair stainless steel plate rack complete assembeled set of (Size: 24 x 30 x 10 inch) fixed with screws as specified and directed

M&L preparation of old/new surface and apply two coat of damp proof chemical ( Acra coat/ Make Dr fixit) over a coat of cement based white putty all as specified and directed by Engr-in-Charge

Providing and injecting chemical emulsion for Post Constructional Anti-termite treatment along the external wall below concrete or masonry apron using chemical emulsion @ 2.25 litres per linear metre including drilling and plugging holes etc. in apron.

Treatment of soil under existing floors using emulsion @ one litre per litre per hole, 300mm apart including drilling and plugging 12mm dia holes with cement mortar 1:2 (1 cement :2 coarse sand) to match the existing floors

Raking out joints/ pointing to squared rubble masonary, cousred or uncoursed in cement or cement lime mortar

M&L for Struck pointing to square rubble masonary, cousred or uncoursed in cement mortar 1:4

Cutting holes in brick walls exc half brick but not exc one brick in cement mortar ore cement lime mortor for inserting hold fasts and making good dismantled portion in cement mortar 1:3 or cement concrete 1:2:4 Type B-1 as required as specified and directed.

Complete removal of existing treatment including padding / plastering / PCC / Brickbat / Coba or any type water proofing treatment.

M&L for provn of water proofing roof treatment to Non accessible RCC roof with APP modified membrane with non woven polyster reinforced wt not less than 3.5 Kg/SqM of thickness not less than 3 mm having thermal; insulation with silver painting on upper side of membrane uniformely embedded during manufacturing process. All as per following specifications:

Conduct ponding test for 72 hrs, after ponding test grouting is to be done at the leakage area.

After the surface is repaired with pressure grouting the slab will be tested for water tightness again for 72 hrs before processing further treatment.

10mm thick plaster in CM (1:4) mixed with and including water proofing compound @ 3% by wt of cement applied over roof slab.

The surface of the roof, parapet and gutters, drain mouths etc over which water proofing treatment is to be applied shall be cleaned of all foreign matters such as fungus, mass, dust etc. By wire brushing and dusting. For cast iron drain outlets the grow shall be cut around to tuck in the treatment as pipes, chimneys stacsetsc and other similar situations to eae up about comers.

Bituminous primer conforming to IS 3348-1986@ 0.3Kg/Sqm to be applied and prepared surface till the surface is properly impregnated.

APP modified water proofing membrane as specified shall be laid on the primer surface by torch application method as per manufacturer instruction, the overlaps while torching shall be 100mm in both directions (longitudinal and transverse directions). All over lap joints shall be sealed throughly by thermofusing both the membrane layers and sealing it with the help of hot trowel. The overlap joints shall be made as monolithic layer.

All joints and changes in direction should be curved with cement mortar (1:3) mixed with SVR latex @ 200ml per bag of cement and cured well before laying the membrane.

Fillet of PCC (1:2:4) type B-0 (using 12.5mm graded crused stone aggregate) 100mm wide and 100mm height in rounded / triangular shape shall be provided at all junctions of vertical and horizontal surfaces and whereever there is a change of direction. The membrane should not be taken over at any steep turns ans hence all corners / junctions should be rounded.

72 hrs testing of treatment for water tightness by ponding of water.

M&L for grout of permanent bonding of strutural damage/ crack, porosity of concrete to attend leakage/ seepage with pressure grouting with 15mm bore GI Pipe Nozzle under the pressure of 5 kg/sqcm using cement based grout, treatment to be made as per instruction complete all as specified

S&F in repairs vitreous china squatting pan of Orissa pattern 580x440 mm white with integral foot rests (excluding flushing cistern and flush pipe) all as specified and directed.

S&F IInd class HW for plain, solid, straight chowkat and framed, rough/ framed rebated on the solid, rounded, or chamfer, put together with glue pinned at joint, all as specified and directed.

M&L Machine cut kota stone slab flooring 20-25mm thick over cement screed base laid & jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing & mirror polishing complete and including screed bed or bedding layer of mortar 20 mm thick for laying floor finish in CM 1:6 all as specified and directed. Note:- Kota Stone should be in one piece and including making of three liunes and moulding etc complete

All as per Item No. 131 above in riser of steps, skirting, dado and pillar laid over cement screed and jointed including 10 mm thick rendering in CM 1:4 for back coat of wall tiling complete all as specified and directed.

M&L for non shrink cementious micro concrete for jacketing on surface of columns, beams and similar structural members with 5 to 12mm stone aggregate in the ratio as per manufacturer's instructions laid to as thickness as directed by Engineer-in-Charge including applying curing compound and use and waste of necessary scaffolding as required.

Taking down copper/aluminium point wiring (light, fan, socket or power) complete, including fixture and fitting such as switches, ceilling roses, pendants, regulator, sockets, light fitting etc for taking credit and making good distrubed surfaces of walls, floors etc.

M & L for point wiring with 1.5 Sqmm multi standard copper conductor 1100 volts grade PVC insulated unsheathed cable drawn in and including in concealed PVC conduit not less than 20 mm dia, medium grade with fitting as approved with PVC insulated unsheathed copper wire green 1.5 Sqmm for continuous earth, sunk in cast iron / MS terminal box duly painted with aluminum inside and black bitumeneous paint all around out side over one coat of anticorrosive paint with 2.8 mm thick bakelite sheet, earth dolly for the following :- (Note :- The rate inclusive of cutting, chasing of stone wall etc and making good to disturbed surface with matching paint/ distemper in existing of any type of wall).

Ditto- One light point/ fan / Exhaust fan/ bell point.

Ditto- One 3 pin socket outlet 5 Amps on independent board

Ditto- One 3 pin socket outlet on same board

Ditto- One 3 pin socket out let 15 Amps on independent board elect wiring 2.5 sqm

One 3 pin socket out let 15 Amps on independent board elect wiring 4.0 sqmm

S&F switch piano type flush button type single pole one way 5 Amps ISI marked complete all as specified and directed.

S&F socket outlet 2 in 1, 5 pin flush 5 Amps complete all as specified and directed .

S&F switch socket combination 6 pin fulsh 15 Amp multi complete all as specified and directed .

S&F bell push flush type SP 5 Amp complete all as specified and directed .

S&F ceiling rose surface bakelite 65mm dia three terminal complete all as specified and directed .

S&F ding dong bell electric single phase suitable for 240 V complete all as specified and directed .

Taking down carefully existing ceiling fan any type any make, incl servicing and painting of ceiling fan with white enameled paint and refixing after celaning and painting and connection with flexible copper wire upto ceiling rose and checking of nuts bolt washers & safety pin etc complete all as specified and directed.

S&F MCB SPN DB made out of Sheet steel enclosure for flush/ surface mounting with bus bar, Earth Stud, neutral link ,SPN 240 volts 200 Amps rated bus bar, 12 way double door openable complete all as specified and directed.

S&F MCB SPN DB made out of Sheet steel enclosure for flush/recessed mounting with bus bar, Earth Stud, neutral link , SPN 240 volts 200 Amps rated bus bar 8 way double door openable complete all as specified and directed .

S&F 6 to 40 Amp MCB single pole 240 V 10 KA complete all as specified and directed .

S&F MCB single pole with netural 240 volts 6 to 40 Amps complete all as specified and directed.

Taking down and disconnecting unserviceable MCB DB from electric system any rating along with wooden Board and making good to distubed surface to match with existing complete all as specified and directed.

M&L for earthing complete with galvanised steel earth plate electrode 600 x 600 x 6 mm thick buried directly in ground earth pit not less than 2.25 mtr below normal GL with the top edge of the plate not less then 1.5 mtr below the normal GL connected to GI wire 4mm dia by means of bolts, nuts, check nuts and washer of galvanised iron or steel and protected by 15mm GI pipe (light grade) and watering pipe 20mm bore GI pipe (light grade) including GI wire meshed funnel and chamber PCC (1:4:8) type D2 using 40mm grade stone aggregate, coping shall be (1:3:6) type C 1 using 20mm stone aggregate with PCC 1:2:4 type B1 (using 20mm graded stone aggregate) pit cover re-inforced with 8mm dia at 80mm c/c both way, incl excavation in any type of soil and hard rock and removal of surplus soil of earth/rock complete all as shown in electrical plate of SSR Part I and as specified including charcoal dust, common salt complete and earth lead connected to earthing test point all as specified and testing of earthing on completion.

M&L for sub main wiring with PVC insulated unsheathed 2 x 6 sqmm stranded copper conductor cable 1100 volts grade heavy duty drawn into PVC rigid concealed conduit with 2.5 sqmm PVC insulated green copper cable for continuos earth wire PVC pipe not less than 20 mm dia with all accessories complete all as specified and directed.

Supply and fixing only ceiling fan regulator Electronic step socket type, 240 Volts, complete all as specified and directed by EIC

Supply & fixing LED tube light fitting, 1 x 18 W, 240 V, luminaire with bipin holders, LED tube rod,connector block, etc. complete with all accessories internally pre-wired and including connecting up with three core twisted flexible copper conductor cable with suitable size complete. Make: Havells cat part no LUMILINEBS18 W LED 865 SPCWH or equivalent make in C&G/ Bajaj/ Wipro.

S&F rectangle closed wooden board recessed size 25 x30x 5 cm depth complete all as specified and directed by EIC

Supply & fixing LED light fitting, 1 x 9 W, complete with all accessories internally pre-wired and including connecting up with three core twisted flexible copper conductor cable with suitable size complete all as specified and directed by EIC. Make: Havells cat part no LUMILINEBS 9W LED 865 SPCWH or equivalent in C&G/ Bajaj/ Wipro.

S & F lamp holder PVC/Polycarbonate type with back plate suitable for batten fitting.

S&F LED bulkhead Luminaires with deep drawn anodised aluminium body epoxy powder coated, heat resistant glass cover with LED 9W etc complete all as specified and directed. Make: Havells cat part no RUGBY NEONFT LOW LED 760 SSYMB OPC or equivalent in C&G/ Bajaj/ Wipro.

Taking down existing geyser by disconnecting all water pipe line connection deposited to MES store and complete all as specified and directed.

Taking down carefully existing Exhaust fan any type any make,incl servicing and painting of with black enameled paint and refixing after celaning and painting and connection with flexible copper wire upto ceiling rose and checking of nuts bolt washers etc complete all as specified and directed.

Taking down carefully existing electric/Electronic meter and reconneted with service wire including fixing on new wooden board with copper wire of suitable size etc and making good to disturbed surface complete all as directed on site.

S&F LED bulb retrofit type of 9/10W complete.

S&F MCB SPN DB made out of Sheet steel enclosure for flush/recessed mounting with bus bar, Earth Stud, neutral link ,SPN 240 volts 200 Amps rated bus bar ,4 way double door openable complete all as specified and directed .

Supply and fixing single phase Electronic energy meter in poly carbonate or sheet steel body ,50 Hz 240 Volts AC, accuracy class I.0 , 5-30A, ISI marked, including all standard anti tamper features, complete. Make: L&T/ HPL/ INDO ASIAN/ AREVA

Supply and fix sheet metal enclosures with socket plug top and MCB's with two pin and earth plug and socket complete with one Single pole MCB 240 V grade 25 Amp complete all as specified and directed .

S&F Water heater storage type (geyser) ,electric, of 50 Ltr capacity, 5 star rated complete. Make: Bajaj/ Racold/ venus

S&F Exhaust fan AC 230 V 50 Hz 300 mm sweep,with frame and louvers complete and connecting with pvc insulated 3 core copper cable of suitable size and making hole complete all as specified and directed by EIC.

S&F ceiling fan complete 1200mm BEE 5 star rated complete with connection with flexible copper wire upto ceiling rose and checking of nuts bolt washers etc complete all as specified and directed.

Note for all items: All items shall be executed as specified and directed by Engr-in-charge.

MS Soumya consultants and designers