Construction of Guard hut store and boundary wall at 220 KV GSS Manda Jaipur

B-1/1.8 Earth work in excavation by mechanical means Hydraulic excavator/manual means in found trenches or drains not exceeding 1.5 M in width or 10 Sqm on plan including dressing of sides and ramming of bottom lift upto 1.5 Mtr including taking out the excavated soil and depositing and refilling of jhiri with watering and ramming and disposal of surplus excavated soil as directed within a lead of 50 Mtr all kind of soils.

B-1/1.2 Earth work in rough excavation, banking excavated earth in layers not exceeding 20cm in depth, breaking clods watering, rolling each layer with 1/2 tonne roller, or stone or steel rammers and rolling every 3rd and top- most layer with power roller of minimum 8-10 tonne capacity and dressing up in embankment for roads, flood banks marginal banks and guide banks or filling up ground depressions, lead up to 50 Mtr. and lift up to 1.5 Mtr.:All kinds of soil

B-3/3.1.6 P&L in position Cement Concrete incl. Curing compaction etc. of specified Grade Excl. the cost of Centering & Shuttering all works up to Plinth level 1:4:8 (1 cement: 4 coarse sand : 8 graded stone aggregate 40mm nominal size)

B-6/6.1.6 Random Rubble stone masonry with hard stone in Foundation and plinth in Cement Sand Mortar 1:6 (1 cement:6 sand) above 30 CM thick walls.

B-5/5.2.2 Brick work with F.P.S brick of class designation 75 in Super Structure above Plinth Level up to floor V level In all shapes and size in CM 1:6 ( 1 cement : 6 coarse sand)

B-5/5.8.3 Half brick masonry Super Structure above Plinth Level up to floor V level using bricks of designation 75 in CM 1:6 ( 1 cement : 6 sand ).

B-5/5.3.1 Add extra for Square of rectangular pillars in superstructure brick work up to five story upto 45 cm length and all sides are free

B-8/(8.13.2.1 + 8.14) Providing &Fixing External Grade board solid core single leaf flush door shutters IS 2202-67 marked using Phenol formal dehydreresin in glue both sides with approved steel fittings complete as per Annexure A 30mm thick commercial veneer both side including providing external lipping with 2nd class teak wood battens 6 mm minimum depth on all edges of shutters (over all area of door shutter to be measured). Extra for providing external lipping with 2nd class teak wood battens 6 mm minimum depth on all edges of shutters (over all area of door shutter to be measured) Over item no. 8.13.

B-4/4.1 Providing and laying in position specified grade of cement concrete for all RCC structural elements upto plinth level including curing, compaction, finishing with rendering in cement sand mortar 1:3 (1 cement: 3 coarse sand) and making good the joints and cost of plastizers (if required) excluding the cost of centering, shuttering and reinforcement. M20 grade Nominal Mix / Design Mix

B-4/4.2 Providing and laying in position specified grade of cement concrete for RCC structural elements upto floor five level including curing, compaction, finishing with rendering in cement sand mortar 1:3 (1 cement, 3 coarse sand) and making good the joints and cost of plastizers (if required) excluding the cost of centering, shuttering and reinforcement for Walls (any thickness) including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and strut etc. M20 grade Nominal Mix / Design Mix

B-4/4.3 Providing and laying in position specified grade of cement concrete for RCC structural elements upto floor five level including curing, compaction, finishing with rendering in cement sand mortar 1:3 (1 cement: 3 coarse sand) and making good the joints and cost of plastizers( if required) excluding the cost of centering, shuttering and reinforcement for Beams, suspended floors, roofs, griders having slopes up to 15º, landings, balconies, shelves, chajjas, lintels, bands, plain windows sills, staircases and spiral staircases etc. M20 grade Nominal Mix / Design Mix

(B-4/4.13.3) Providing and fabricating reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding (including cost of binding wire) all complete up to floor five level. ('Original producers' who manufacture billet directly from iron ores and roll the bilets to produce steel conforming to IS:1786) Thermo Mechanically treated bars bars (IS : 1139).

B-4/4.9 Centering and Shuttering with plywood or steel sheets including strutting, propping bracing both ways and removal of formwork for foundation, footings, strap beam, raft, bases of columns etc.

B-4/4.10.2 Centring & Shuttering with plywood or steel sheets including strutting propping bracing both ways with steel props and removal of formwork for up to floor five level for: Suspended floor, roofs, landings, staircases, balconies girders, cantilevers, bands, coping bed plates, anchor blocks, sills,chajjas, lintel beams, plinth beam etc.

B-4/4.10.3 Centring & Shuttering with plywood or steel sheets including strutting propping bracing both ways with steel props and removal of formwork for up to floor five level for: Columns, pillars, posts and struts etc.

B-6/6.17.3 Supplying &Fixing machine cut and polished stone shelves tands and sills in CM 1:3 with machine cut edges Kota stone minimum 30 mm thick

B-11/11.19.2 Kota stone slabs 25 mm thick in risers of steps, skirting, dado and pillars laid on 12 mm (average) thick cement mortar 1:3 (1 cement 3 coarse sand) and jointed with grey cement slurry mixed with pigment to match the shade of the slabs, including rubbing and polishing complete For area of each slab from 2001 to 5000 Sqcm

B-11/11.18.12 Kota stone slab flooring 25 mm thick over 20 mm (average) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete with base of cement mortar 1 : 4 (1 cement : 4 coarse sand) For area of each slab from 2001 to 5000 sqcm

B-9/9.19.3+9.25 Providing and fixing steel glazed doors windows and ventilator shutters of standard rolled steel section joints mitred and welded with steel lugs 13x3mm, 10cm. long embedded in cement concrete block 15x10x10cm. of 1:3:6 (1cement : 3 coarse sand : 6 graded stone aggregate 20mm nominal size) or with wooden plugs and screws or rawl plugs and screws with fixing clips or with bolts and nuts as required including providing and fixing of pin headed glass panes 4mm thick with cooper glazing clips and special metal sash putty of approved make or metal beading with screws complete including priming coat of approval steel primer, excluding the cost of metal beading and other fitting except necessary hinges of pivots steel handles peg stay etc. as required :Windows side hung /Ventilators top or centre hung (openable)

B-9/9.26 Supplying and fixing fixed wire gauge of 14 mesh x 24 gauge to the metal frame of rolled section by metal beading 20x3mm with suitable screw at not exceeding 150mm distance.

B-9/9.27 Providing and fixing Square bars or other flat welded to window, ventilatiors etc.

B-10/10.20 P/F 20mm thick precast terrazo tiles of appd make with marble chips of size upto 6mm laid over roof with neat cement slurry mixed with pigment to match the shade of the tiles, incl cutting grinding rubbimg with m/c complete on 20mm thick bed of cement sand mortar 1:4

B-3/3.2.3 Providing and laying cement concrete including curing, compaction etc. complete in retaining walls, return walls, walls (any thickness) including attached pilasters, columns, piers, abutments, pillars, posts, struts, buttresses, string or lacing courses, parapets, coping, bed blocks, anchor blocks, plain window sills, fillets, levelling course etc up to floor five level excluding the cost of centering and shuttering.M15 grade Nominal Mix 1:2:4(1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size).

B-10/10.17.1 Grading roof for water proofing treatment with water proffing compound Cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size)

B-12/12.3.2 Plaster on new surface on walls in Cement Sand Mortar 1:6 incl. Racking of joint etc. complete fine finished 20mm thick

B-12/12.3.3 Plaster on new surface on walls in Cement Sand Mortar 1:6 incl. Racking of joint etc. complete fine finished 12mm thick

B-12/12.5 6 mm thick cement plaster to ceiling of mix 1:3 (1cement : 3-fine sand)

B-11/11.17.4 Chequered precast cement concrete tiles 22mm thick in footpath and courtyard jointed with neat cement slurry mixed withpigment to match the shade of tiles including rubbing and cleaning etc complete on 20mm thick bed of C.M. 1:4(1 cement: 4 coarse sand) ordinary cement without any pigment

(B-9/9.39) Providing and fixing of double leaf steel shutter for cupboard, the frame is made of pressed steel ISI section 80x25 mmx 1.25 mm thick with 1.00 mm MS sheet to spot welded including holdfasts of 15x3mm, MS oxidized fittings such as butt hinges, sliding doors bolts, handles, tower bolts and twin peg etc complete including applying priming coat of approved steel primer of red oxide zinc chromate and spray painting in approved shade with deco paint of approved quality complete as per direction of Engineer In Charge

B-12/12.20 Making of drip course (Tapka) in cement sand mortar 1:6 width upto 40 mm and 10 mm thick as per approved design

B-10/10.22 Providing gola 75x75 mm in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 stone aggregate 10mm and down gauge) including finishing with cement mortar 1:3 (1 cement : 3 fine sand) as per standard design :

B-9/9.13 Supplying and fixing rolling shutters of approved make, made of 80 x 1.25mm. M.S. laths interlocked together through their entire length and jointed together at the end by end locks mounted on specially designed pipe shaft with brackets, side guides and arrangements for inside and outside locking with push and pull operation complete including cost of spring hooks, providing and fixing necessary 25.3cm. long wire springs grade No. 2 and M.S. top cover 1.25mm thick for rolling shutters as per design & IS 6248- 1979. (Clear openable area to be measured for payment).

B-9/9.2 Structural steel work riveted, bolted or welded in built up sections, trusses and framed work , including cutting, hoisting (height up to 10 m), fixing In position and applying a priming coat of approved steel primer all complete:

(B-9/9.8.1) Providing and fixing steel gate, grating , and grills made of angles, tees, square bars, flats,or black pipe with holdfast and fittings complete as per design and drawing including cutting welding and fabrication with priming coat of red oxide Extra if square,rectangular hollow tubelar sections are used or grill made by flats only

B-9/9.5 P&F T-iron frames for doors windows and ventilators of mild steel Tee section joints mitered and welded with 15x3mm long 10 CM long embedded in CC block 15x10x10 CM of 1:3:6 (1 cement : 3 core sand: 6 stone agrregate 20 MM nominal size) or with wooden plugs and screw or rawl plug and screws or with fixing clips or with bolts and nuts as reqd,. incl. Fixing of nece. Butt hinges and screw and applying priming coat of appd. Steel primer.

B-9/9.33+9.35 P&F galvanized barbed wire.

B-12/12.46.1 Painting with synthetic enamel paint of approved brand and manufacture to give an even shade two or more coats on new work

B-12/12.35.1 Colour washing of all shades to give an even shade including all scaffolding : New work (two or more coats) with a base coat of white washing with lime.

(B-12/12.37.1) Distempering with oil bound washable distemper of approved brand and manufacture to give an even shade including all scaffolding:New work (two or more coats) over and including scrapping and priming coat with cement primer.

B-12/12.42 Finishing walls with Acrylic smooth exterior paint of required shade including all scaffolding New work(Two or more coat applied @ 1.67ltr/10 sqm over and including base coat of water proofing cement paint applied @ 2.20 kg/ 10sqm)

B-3/3.8 P&F precast CC coping 1:2:4 mix 50mm thick complete as per specification

S-1/1.2.2 P & F Indian type white glazed vitreous China Ist quality W.C Orissa Pan IS 2556 mark with 100mm vitreous China P or S trap incl. Cutting and making good the wall and floor size 580 x 440 mm

S-1/1.20.2 P&F low level flushing cistern of 10 Ltr cap. IS 2556 mark of appd,. Make with complete fitting CI brackets duly painted brass ball cock with ball IS 1703 mark complete incl. Cutting and making good the wall PVC with PVC bend as per IS 7231

S-1/1.36.3 P&F WVC wash basin Ist quality IS 2556 mark of appd,. Make with CI brackets duly painted 1 No. 15mm C.P. pillar cock IS 8934 mark & 32mm C.P. brass waste coupling of appd,. Make 25mm G.I. waste pipe complete incl. Cutting and making good the wall size 550x400mm

S-1/1.45.1 P&F looking mirrors with PVC frame of appd. Quality Atul or equivalent size 500x400mm

S-1/1.47.8 P&F towel rail or ring of appd. Quality / make C.P. Brass Towel Ring revolving type

S-2/2.1.1B P & F G.I. pipes (Internal Work) with G.I. Fittings (IS 1239-1992 mark) and MS clamp including cutting and making good the walls and floors: Exposed on wall 15 mm dia nominal bore 'B' Class

S-2/2.1.9 B P & F G.I. pipes (Internal Work) with G.I. Fittings excluding union (IS:1239 Mark) & MS clamps including cutting and making good the walls and floors:Concealed pipe in wall including painting with anticorrosive bitumen paint 15 mm nominal dia. Class B

S-2/2.1.3B P & F G.I. pipes (Internal Work) with G.I. Fittings (IS 1239-1992 mark) and MS clamp including cutting and making good the walls and floors: Exposed on wall 25 mm dia nominal bore 'B' Class

S-2/2.2.3 P&F G.I. pipes (external work) with G.I. fittings (IS:1239 - 1292 Mark) including union IS 1239 mark & MS clamps incl. Cutting and making good the wall and floor B Class 25mm dia

S-2/2.3.1 Making connection of G.I. distribution branch with G.I. main including all fitting. Upto 25mm dia

S-2/2.7.3 P&F bib cock IS 8931 mark superior quality of appd. Make C.P. brass bib cock 15mmdia nominal bore

S-2/2.7.4 P&F bib cock IS 8931 mark superior quality of appd. Make C.P. brass long body 15mm dia Weight not less than 690 Gram

S-2/2.8.5 P&F stop cock IS 8931 mark superior quality & of approved make C.P. brass concealed stop cock 15mm

S-3/3.44.2 Providing and Fixing Unplasticized Poly Vinyl Chloride (UPVC) SWR Pipes Type B for sciland waste discharge system (IS:13592 : 1992 Marked) of approved quality /make 110mm dia

S-3/3.45.4 Providing and Fixing Unplasticized Poly Vinyl Chloride (UPVC) SWR Pipes Type B for sciland waste discharge system (IS:13592 : 1992 Marked) of approved quality /make 110mm dia bend 87.5 Dg

S-3/3.45.17 Providing and Fixing Unplasticized Poly Vinyl Chloride (UPVC) SWR Pipes Type B for sciland waste discharge system (IS:13592 : 1992 Marked) of approved quality /make 110mm dia Single Tee with Door

S-3 /3.45.30 Providing and Fixing Unplasticized Poly Vinyl Chloride (UPVC) SWR Pipes Type B for sciland waste discharge system (IS:13592 : 1992 Marked) of approved quality /make 110mm diaVent Cowel 100mm

S-3/3.45.11 Providing and Fixing Unplasticized Poly Vinyl Chloride (UPVC) SWR Pipes Type B for sciland waste discharge system (IS:13592 : 1992 Marked) of approved quality /make 110mm diaSocket plug

S-3/3.45.6 Providing and Fixing Unplasticized Poly Vinyl Chloride (UPVC) SWR Pipes Type B for sciland waste discharge system (IS:13592 : 1992 Marked) of approved quality /make 110mm dia Door bend 87.5 Dg.

S-3/3.45.5 Providing and Fixing Unplasticized Poly Vinyl Chloride (UPVC) SWR Pipes Type B for sciland waste discharge system (IS:13592 : 1992 Marked) of approved quality /make 110mm dia Door bend 45 Dg

S-3/3.45.12 Providing and Fixing Unplasticized Poly Vinyl Chloride (UPVC) SWR Pipes Type B for sciland waste discharge system (IS:13592 : 1992 Marked) of approved quality /make 110mm diaPipe Clip

S-3/3.45.26 Providing and Fixing Unplasticized Poly Vinyl Chloride (UPVC) SWR Pipes Type B for sciland waste discharge system (IS:13592 : 1992 Marked) of approved quality /make 110mm diaNahni Trap without Jali 4"

S-3/3.16.2 P&F rigid PVC pipe (IS 4985 mark) class IInd /4 Kg P.SqCM ) approved quality / make including jointing the pipe with solvent cement rubber ring and lubricant 75 mm dia

S-3/3.16.3 P&F rigid PVC pipe (IS 4985 mark) class IInd /4 Kg P.SqCM ) approved quality / make including jointing the pipe with solvent cement rubber ring and lubricant 110mm dia

S-1/1.60 Providing & fixing C.P. flange for 15mm dia taps

S-2/2.26.3 P&F PVC storage tank IS 12701 marked indicating the BIS license No. of approved make with cover 25mm dia 1 M long GI over flow pipe & 25 CM long wash out pipe with plug & socket incl. Making conn. Etc. complete of appd. Design 500 Ltr capacity

S-2/2.15.1 P&F full way valve IS 778 mark or wheel valve of approved Make gun metal 15mm Nominal Bore

S-2/2.15.3 P&F full way valve IS 778 mark or wheel valve of approved Make gun metal 25mm Nominal Bore

S-2/2.13.2 P & F 15 mm. Dia Connection Pipe of approved quality/make : PVC pipe with C.P. Brass nuts upto length, 370mm

S-2/2.11.1 P&F ball cock IS 1703 mark with rod & PVC ball complete brass Weight 400 Gram 15mm dia

S-3/3.3.2 Providing & Laying C.C. 1:5:10 (Stone aggregate 40mm nominal size) upto haunches of S.W. pipes including 150 mm thick bed concrete (Width W= Dia of pipe in Cm+ 30Cm.) concrete width to be reduced from width W at center of pipe to `0` at top of pipe. (Excluding cost of pipe) 150mm dia S.W pipe

S-3/3.19.1 Construction of manhole in all type of soil inner size 90x60 CM 450mm thick masonry in CM 1:6 10 CM thick CC 1:5 :10in foundation 20mm thick inside plaster in CM 1:6 finished with floating neat cement 50mm thick M-15 Gr CC flooring making channels 80mm thick stone slab covering with 40mm thick M-15 Gr CC flooring RCC cover with frame of 450mm dia E/W etc. complete as per design incl. Disposal of surplus earth within 50 Mtr Depth upto 0.50mtr.

S-3/3.5.1 P & F Square-mouth gully trap `A` grade (IS 651-1992 :marked) of approved make complete with C.I. grating, frame & Cover masonary chamber in C.M. 1:6, 100mm thick C.C. 1:5:10 base concrete, 40mm thick C.C.M-15 grade coping, 12mm thick cement plaster in CM 1:3 complete as per approved design & type.Trap size 150 X 100mm, ferrow cement cover with frame, Internal Chamber size 300 X 300mm.

S-3/ 3.22.1 Construction of Soakage well in all type of soil 300 mm thick dry masonry ,top and bottom 300 mm course in CSM 1:6,80 mm thick stone slab, jointing of slab in CM 1:3.Ralthal,Kharanja,40 mm thick M-15 grade C.C. flooring, earth work complete as per approved including disposal of earth with in a lead 50 mtr. Size 300 Cm. dia. Outside & 300 Cm depth

(S-3/3.27.1) Construction of septic Tank in all types of soil with 40 Cm .thick masonry in CM 1:6, 15 Cm thick C.C bed of 1:5:10, M-15 grade C.C floor & RCC slab covering with M15 grade c.c. floor, 50 mm thick stone slab partition walls, 20 mm thick plaster in CM 1:6 finished with neat floating cement, 4 Nos stone foot rests of approved design ,two No. 450 mm dia each Ferro cement cover with frame, earth work etc. complete as per approved drawing including disposal of surplus earth within a lead of 50 mtr:-Size 200x100x130 cm.(for 10 users) with 115 mm thick RCC (M-20) slab with Tor steel reinforcement 8mm ϕ @15 cm c/c bothways including shuttering complete in all respect

S-2/2.12.1 P&F inlet connection (Angle valves) superior quality of approved make for wash basin Gyser etc . C.P. inlet connection 15mm brass (IS 8931 marked)

S-1/1.52.2 P&F soap dish or tray of appd,. Quality make IS 2556 marked C.P.Brass heavy and superior quality.

(S-1/1.38.9.2) P & F Kitchen & Lab. Sink of approved make with C.I. brackets duly painted, 40 mm C.P. waste coupling, C.P. Brass chain with rubber plug, 40 mm G.I. waste pipe up-to floor level complete including cutting and making good the wall & floor :1.0 mm thick stainless steel AISI -304 & IS 13983-1994 kitchen sink of approved make as per Engineer-in-charge with large waste coupling. 22 x 18 x 7 20x16x7

B-1/1.25 Filling available excavated earth (excluding rock) in trenches, plinth side of foundation etc. in layers not exceeding 20 cm. in depth, consolidating each deposited layer by ramming and watering including lead up to 50 meter and with all lift.

E-01/1.1.1 Wiring of light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq. mm nominal size FR PVC insulated unsheathed flexible copper conductor 1.1 kV grade and 1.5 sq. mm nominal size FR PVC insulated unsheathed flexible copper earth conductor 1.1 kV grade (IS:694) in recessed ISI marked MMS ( IS:9537 P - III ) virgin material PVC conduit & it's ISI marked (IS:3419-1988) accessories, round tiles, 1.2 mm thick Hot Dipped Galvanized Modular Box with earth terminal, 10A Modular switch,Modular face plate with grid plate, 3 pin ceiling rose / Holder /3 way connector, screws, making connections, testing etc. as required. For specification of copper Conductor, Phenolic Laminated sheet's & Electrical/ Wiring accessories refer Chapter E - 04, E - 05 & E - 07 For additional technical parameters of product / work refer Annexure 'A' attached with this BSR:short point (upto 3.0 m)

E-01/1.1.2 Wiring of light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq. mm nominal size FR PVC insulated unsheathed flexible copper conductor 1.1 kV grade and 1.5 sq. mm nominal size FR PVC insulated unsheathed flexible copper earth conductor 1.1 kV grade (IS:694) in recessed ISI marked MMS ( IS:9537 P - III ) virgin material PVC conduit & it's ISI marked (IS:3419-1988) accessories, round tiles, 1.2 mm thick Hot Dipped Galvanized Modular Box with earth terminal, 10A Modular switch,Modular face plate with grid plate, 3 pin ceiling rose / Holder /3 way connector, screws, making connections, testing etc. as required. For specification of copper Conductor, Phenolic Laminated sheet's & Electrical/ Wiring accessories refer Chapter E - 04, E - 05 & E - 07 For additional technical parameters of product / work refer Annexure 'A' attached with this BSR:Medium point (upto 6.0 m)

E-01/1.1.3 Wiring of light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq. mm nominal size FR PVC insulated unsheathed flexible copper conductor 1.1 kV grade and 1.5 sq. mm nominal size FR PVC insulated unsheathed flexible copper earth conductor 1.1 kV grade (IS:694) in recessed ISI marked MMS ( IS:9537 P - III ) virgin material PVC conduit & it's ISI marked (IS:3419-1988) accessories, round tiles, 1.2 mm thick Hot Dipped Galvanized Modular Box with earth terminal, 10A Modular switch,Modular face plate with grid plate, 3 pin ceiling rose / Holder /3 way connector, screws, making connections, testing etc. as required. For specification of copper Conductor, Phenolic Laminated sheet's & Electrical/ Wiring accessories refer Chapter E - 04, E - 05 & E - 07 For additional technical parameters of product / work refer Annexure 'A' attached with this BSR:Long point (upto 10.0 m)

E-01/1.3.1 Wiring of 3/5 pin 6 amp. Light plug point with 1.5 sq. mm nominal size FR PVC insulated unsheathed flexible copper conductor 1.1 kV grade and 1.5 sq. mm nominal size FR PVC insulated unsheathed flexible copper earth conductor 1.1 kV grade(IS:694) in recessed ISI marked MMS ( IS:9537 P - III ) PVC conduit & it's ISI marked (IS:3419-1988)accessories, Hot Dipped Galvanized Modular box of 1.2 mm thick with earth terminal, 10 A modular switch, 3/5 pin 6 A modular socket, Modular face plate with grid plate, screws, making connections, testing etc. as required. For specification of copper Conductor, Phenolic Laminated sheet's & Electrical/ Wiring accessories refer Chapter E - 04, E - 05 & E - 07 For additional technical parameters of product / work refer Annexure 'A' attached with this BSR:on board

(E-4/4.1.2) Supplying and drawing FR PVC insulated & unsheathed flexible copper conductor as per PWD specification for electrical Works with ISI marked (IS:694) and as per IS 8130 : 2013 of 1.1 kV grade . Wire should be made from 99.90 % purity copper, class 5 stranding in acc. to IS:8130/IEC 60228 for lower watt loss , oxygen free for less chances of oxidization, insulation PVC type A/C/D , flame retardant as per IS 10810-53, better amperage rating as per IS:3961 part 5, in existing surface or recessed PVC/ MS conduit/casing capping making connections with Copper Lugs of suitable size, Ferrules,testing etc. as required. OEM Must have its own in house NABL lab setup for all testing facilities for wires. For additional technical parameters of product / work refer Annexure 'A' attached with this BSR 2 x 1.5 sq.mm

(E-4/4.1.6) Supplying and drawing FR PVC insulated & unsheathed flexible copper conductor as per PWD specification for electrical Works with ISI marked (IS:694) and as per IS 8130 : 2013 of 1.1 kV grade . Wire should be made from 99.90 % purity copper, class 5 stranding in acc. to IS:8130/IEC 60228 for lower watt loss , oxygen free for less chances of oxidization, insulation PVC type A/C/D , flame retardant as per IS 10810-53, better amperage rating as per IS:3961 part 5, in existing surface or recessed PVC/ MS conduit/casing capping making connections with Copper Lugs of suitable size, Ferrules,testing etc. as required. OEM Must have its own in house NABL lab setup for all testing facilities for wires. For additional technical parameters of product / work refer Annexure 'A' attached with this BSR 2 x 2.5 sq.mm

(E-4/4.1.11) Supplying and drawing FR PVC insulated & unsheathed flexible copper conductor as per PWD specification for electrical Works with ISI marked (IS:694) and as per IS 8130 : 2013 of 1.1 kV grade . Wire should be made from 99.90 % purity copper, class 5 stranding in acc. to IS:8130/IEC 60228 for lower watt loss , oxygen free for less chances of oxidization, insulation PVC type A/C/D , flame retardant as per IS 10810-53, better amperage rating as per IS:3961 part 5, in existing surface or recessed PVC/ MS conduit/casing capping making connections with Copper Lugs of suitable size, Ferrules,testing etc. as required. OEM Must have its own in house NABL lab setup for all testing facilities for wires. For additional technical parameters of product / work refer Annexure 'A' attached with this BSR 2 x 4 sq.mm

E-01/1.4.1 S&F following sizes (dia.) of ISI marked virgin material MMS ( IS:9537 P - III ) PVC conduit along with ISI marked (IS:3419-1988) accessories as required in recess including cutting the wall, covering conduit and making good the same as required. For additional technical parameters of product / work refer Annexure 'A' attached with this BSR:20mm

(E-7/7.36) Providing and fixing of power plug point with non modular accessories as per PWD specification for electrical Works with Galvanized box of 1.2 mm thick with earth terminal with suitable size phenolic laminated sheet (IS : 2036 - 1995) cover including cost of 16 amp. Switch (IS :3854) and 3/6 pin 16 amp. socket outlet making connection , testing , etc. as required. . For specification of Wiring accessories refer Chapter E - 07 related item & For additional technical parameters of product / work refer Annexure 'A' attached with this BSR

(E-7/7.24) Providing & Fixing of ISI marked surface type buzzer (IS:2268-1994) with CM/L no. printed including making connection testing etc. as required. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure "A" attached with this BSR .

E-17/17.1.1 Providing & Fixing of IP20 SMD Mid Power LED batten type integrated light fixture made from Powder coated Extruded aluminium housing with in built driver , System lumen efficacy ≥ 110 lm/Watt output, internal surge protection of 2.5 KV with Short & Open circuit protection ,THD < 10% , P. F.≥0.95, CRI >80 , life time of minimum 50000 Burning Hours with , 70% of intial Lumen maintaned till life ends , CCT 3000°K / 4000°K / 5700°K /6000°K/6500°K (As per ANSI Bin) , Maximum power consumption should not more than the specified rating and Fixture shall be of BIS standard and trade mark certificate ( T.C.). Manufactures Word Mark/ Name Engraved/ Embossing/ Screen printing on housing. OEM must have its own in house NABL lab setup for all testing facilities for LED fixtures. (LM79 & LM80) certificate / Report from OEM shall be submitted. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure "A" attached with this BSR :1170mm (+/-10%) LED batten with min. lumen output 2200 lm

E-18/18.12.2 Providing & Fixing of IK08, IP 66 protected LED Street Light Luminaire on existing bracket/pole. Fixture made of powder coated single piece pressure die cast aluminum material with heat dissipation fins on housing with UV stabilized PC (UV stablization report submitted for UV cover ) /Toughened Glass cover and secondary lens on each LED & should be SMD type of 3 to 5 watt each . The System efficacy >=125 lm/ wt and potted driver & has a unique BIS R number with Input Voltage AC 120 to 270 V AC with High voltage Cutoff @>=300 V AC and Auto resetting Safety , Power Factor >0.95 driver Efficiency >85% ,THD(I) <10% Humidity 10% to 90% RH Working Temp -5C to 45C . driver current <750mA. The luminaire shall be BIS certified and Trade mark certified. Life Expectancy Equal or more than 50000 burning hrs with Minimum 70% lumen maintened , CRI >70 and CCT 5700K +355K. Surge protection shall be min ≥ 4 KV internal and min 10 KV external inside driver compartment. driver should be Phase to phase protection of 440 V for 4 Hrs. Manufactures Word Mark/Name Engraved/Embossing on die cast housing to allow traceability/authenticity. Fixture shall be AS PER IS 10322 Complianced.OEM Must have its own in house NABL lab setup for all testing facilities for LED fixtures. (LM79/LM80) Certificate/ report with liable warranty of product/accessories from OEM shall be submitted. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure "A" attached with this BSR .LED Street Light fixture with Minimum lumen output 3700 lm

E-15/15.10 P & F 1.2mm thick M.S. Recessed fan box, hexagonal/ round of size 130 mm dia, depth 75mm, 12 mm dia rod fan hook with 100 mm length extended on each side . All as per pre approved by Engineer in charge. For additional technical parameters of product / work refer Annexure 'A' attached with this BSR

(E-15/15.7.3) Providing & Fixing of BEE Star rated copper wounded double ball bearing capacitor start, aluminium body & Metallic blade ceiling fan Conforming to all the performance requirements laid down in IS 374:2019 including all amendments, as applicable ; & Carry BIS licensing (i.e. ISI marking) with down rod up to 80 cm with secondary support safety cable ( steel rope) , cotter pin with 3 x 1.5 sq.mm pvc insulated flexible copper conductor making connection testing etc. as required. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure "A" attached with this BSR. 1200 mm Sweep BEE 3 Star rated (service value >=5.0 to< 5.5 )

E-15/15.16 Providing & Fixing of extra down rod of 15 mm dia . ERW (Electrical resistance welded ) of 1.6mm nominal thick medium duty steel pipe including cutting, threading, drilling, fixing quarter pin etc as reqd. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure "A" attached with this BSR .

E-06/6.1.1.2 Providing & Fixing of 240/415 V AC MCB with positive isolation of 10 kA breaking capacity (B/ C/D tripping characteristic as per type of load and site requirement) 4 KV impulse withstand voltage, ISI marked IS 8828(1996) / conforming to IEC 60898-1 2002, IEC 60947-2, low watt losses, trip free mechanisum , energy limiting of class 3 as per IEC, minimum phase termination capacity of 35sq.mm. , conductor line load reversibility , IP 20 contact protection and fitted in existing distribution board/sheets, minimum electrical operation 20,000 upto 20 A rating and 10,000 upto 63 A, 5000 for 80 A & above rating including making connections, testing etc. as required. OEM shall have submit NABL / CPRI / ERDA accrediated lab type test reports & All as per pre approved by Engineer in charge. For additional technical parameters of product / work refer Annexure 'A' attached with this BSR:6A to 32A rating

(E-6/6.2.1.2) Providing & Fixing of 240/415 V isolator ISI marked IS:13947-III/conforming to IEC 60947-3, suitable for AC22A utilization category, 4KV impulse withstand voltage, true contact indication, Red colour dolly / lever shall have single mould covering over all poles for operation , two position din rail mounting, minimum phase termination capacity of 35sq.mm. IP 20 contact protection and fitted in existing distribution board / sheet including making connections, testing etc. as required. OEM shall have submit NABL / CPRI / ERDA accrediated lab type test reports & All as per pre approved by Engineer in charge.For additional technical parameters of product / work refer Annexure 'A' attached with this BSR Double pole isolator 63 A rating

(E-6/6.10.1.3) Providing & Fixing of Recessed/surface mounting heavy duty horizontal type Double Door ( Metal / Glazed )Distribution board with Metal end box made out from Galvanized steel / CRCA sheet not less then 1.2 mm thick conforming to IS-8623-1 & 3 / IEC 61439- 1 & 3, powder painted complete with reversible door (for double door DB only )100 amp. insulated copper bus bar/shorting link , copper neutral link, copper earth link , color coded interconnecting wire set of suitable rating and din bar,masking sheet, making internal DB terminations with copper lugs, Ferrules, detachable gland plate, including making connections, testing etc. as required. OEM shall have submit NABL / CPRI / ERDA accrediated lab type test reports & All as per pre approved by Engineer in charge. For additional technical parameters of product / work refer Annexure 'A' attached with this BSR Metal door (single phase) IK-09 and IP-43 with Metal end box 8 Way (8+2)

E-14/14.2 Plate Earthing as per IS:3043 with Hot dipped G.I. Earth plate of size 600mm x 600mm x 6.0mm by embodying 3 to 4 mtr. below the ground level with 20 mm dia. G.I. 'B' class watering Pipe ,including all accessories like nut, bolts, reducer, nipple, wire meshed funnel, and Heavy duty weather proof poly-propylene earth pit chamber with lockable Jam free lid suitable for safe working load 5000 Kg or more of size Top Dia. 225 to 260 mm, Bottom Dia 300 to 350 mm. and Height 250 to 300 mm. and embodying the pipe complete with alternate layers salt and coke/ charcoal, testing of earth resistance for value of 5 ohms or less as required & must record by engineer in charge during site visit and ensure to enter in measurment book.All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure "A" attached with this BSR .

E-14/14.6.9 Supply & Laying following size earth wire in horizontal or vertical run in ground/surface/recess including riveting, soldering, saddles, making connection with GI/Cu purity purity >95% thimble etc. as required. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure "A" attached with this BSR. 10 SWG G.I. ( Hot Dipped ) Wire

(E-11/11.2.3.1) Providing & Laying P.V.C. / XLPE insulated & P.V.C. sheathed Arrmoured Aluminium cable confirming to IS:1554 P-I / IS :7098 P - I of 1.1 KV with H4- Grade electrolytic aluminium conductor confirming to IS 8130 of purity >99.6 %, round / flat strip armouring of cables, Inner / outer sheath confirming to IS:5831 in existing RCC / Hume / Stoneware / PVC pipe/ open duct/cable trench / Cable tray(with cable tie) including testing etc. as required of following size. OEM must have it's own in house NABL accrediated Laboratory for testing procedure as per IS:10810.For additional technical parameters of product / work refer Annexure 'A' attached with this BSR 10.0 Sq. mm 2 Core

E-07/7.21 Providing & Fixing of IS 11037:1984 marked non modular socket size flush type 180 watt rotary minimum 5 step fan regulator with CM/L no. printed and made out from industrial grade Polycarbonate or fire resistant ABS material including making connection testing etc. as required.All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure "A" attached with this BSR .

E-18/18.10.1 Providing & Fixing of IK08 IP65 protected Top/Bottom mounted LED Post top Luminarie made of single piece construction powder coated die cast alluminium housing with UV stabalized Clear / frosted Polycarbonate diffuser and Aluminium anodised with sand blast reflector. The System level Luminous efficacy ≥ 100 Lumen/W. SMD LEDs is to be used, System CRI>70, CCT: 3000/4000/6500 K. The integral electronic driver must be potted & has a unique BIS R number must be potted & has a unique BIS R number constant current and Internal/external surge protection device of min. 4KV(L-N) and efficiency > 85%, PF>0.9, THD<10% and input Voltage range of 140-270V AC at 50Hz. System life of 50000 Burning hours with 70% of Initial Lumens maintained . Driver current <750mA. Fixture must be in compliance with BIS Standards and Trade mark Certificate complete in all respect.OEM Must have its own in house NABL lab setup for all testing facilities for LED fixtures. (LM79/LM80) Certificate/ report with liable warranty of product/accessories from OEM shall be submitted. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure "A" attached with this BSR . Minimum lumen output 2500 lm Post top Luminarie

Please Enable Macros to View BoQ information