TP1-027/20-21

Amount

Soil investigation & Design using STAAD software based on the foundation recommendation as per soil test report and as per the requirement, including, preparation of Drawings for all the components of the proposed construction and submission of drawings 6 copies+2 soft copies of AutoCAD drawing, after getting approval from the competent authority, including cost of all materials, labour, leads, lifts T&P etc complete

Conducting Geophysical survey to assess the availability of ground water and to locate the place of bore well

Earth work excavation for foundation in ordinary soil with lead of 10 to 100 m and lift of 3m in sand, silt or other loose soil, wet sand, or silt not under water, light black cotton soil, sandy loom and ordinary soil including excavated earth.

Supplying and filling in foundation and basement with filling sand in layers not more than 15 cm thick well rammed and watered consolidated etc complete as per standard specification

Transporting the surplus excavated earth, debris etc away from the site to a lead of 5km including cost of all lead, lift, conveyance , loading, unloading etc. complete

Re filling in foundation with excavated earth in layers not more than 15 cm thick well rammed and watered consolidated etc complete as per standard specification

Providing Anti-termite treatment in four stages i) Immediately after ewe and before laying of foundation concrete ii) before refilling sides of foundation iii) Before laying of flooring concrete and iv) outside of basement upto 1m alround the building with approved anti-termite chemicals as specified by the manufacturer including cost of all materials, lead etc. complete.

Laying PCC 1:3:6 mix using 20mm HBG machine crushed metal for foundation matt concrete including cost of all labour, materials, lead, lift, curing etc.complete

Laying PCC 1:2:4 mix using 20mm downgraded HBG machine crushed metal for foundation concrete including form work, cost of all labour, materials, lead, lift, curing etc. complete as per standard specification.

Providing and laying in position machine batched, machine mixed and machine vibrated design mix cement concrete of M25 grade with a minimum cement content of 360 kg per cu.m for reinforced concrete structural elements under controlled water cement ratio with plasticiser using 20mm and downgraded metal including form work, but excluding cost of steel reinforcement. (up to basement level) for Foundation & Basement.

Providing and laying in position machine batched, machine mixed and machine vibrated design mix cement concrete of M25 grade with a minimum cement content of 360 kg per cu.m for reinforced concrete structural elements under controlled water cement ratio with plasticiser using 20mm and downgraded metal including form work, but excluding cost of steel reinforcement. (up to basement level) Grade beam

Providing and laying in position machine batched, machine mixed and machine vibrated design mix cement concrete of M25 grade with a minimum cement content of 360 kg per cu.m for reinforced concrete structural elements under controlled water cement ratio with plasticiser using 20mm and downgraded metal including form work, but excluding cost of steel reinforcement. (up to basement level) Plinth beam

Providing and laying in position machine batched, machine mixed and machine vibrated design mix cement concrete of M25 grade with a minimum cement content of 360 kg per cu.m for reinforced concrete structural elements under controlled water cement ratio with plasticiser using 20mm and downgraded metal including form work, but excluding cost of steel reinforcement. (up to basement level) RCC raft

Providing and laying in position machine batched, machine mixed and machine vibrated design mix cement concrete of M25 grade with a minimum cement content of 360 kg per cu.m for reinforced concrete structural elements under controlled water cement ratio with plasticiser using 20mm and downgraded metal including form work, but excluding cost of steel reinforcement. (up to basement level) Column up to basement

Providing and laying in position machine batched, machine mixed and machine vibrated design mix cement concrete of M25 grade with a minimum cement content of 360 kg per cu.m for reinforced concrete structural elements under controlled water cement ratio with plasticiser using 20mm and downgraded metal including form work, but excluding cost of steel reinforcement. (up to basement level) RCC wall

Providing and laying in position machine batched, machine mixed and machine vibrated design mix cement concrete of M25 grade (with a minimum cement content of 360 kg per cu.m) for reinforced concrete structural elements under controlled water cement ratio with plasticiser using 20mm and downgraded metal including form work, but excluding cost of steel reinforcement. G floor Column

Providing and laying in position machine batched, machine mixed and machine vibrated design mix cement concrete of M25 grade (with a minimum cement content of 360 kg per cu.m) for reinforced concrete structural elements under controlled water cement ratio with plasticiser using 20mm and downgraded metal including form work, but excluding cost of steel reinforcement. G floor Cast in situ cover slab

Providing and laying in position machine batched, machine mixed and machine vibrated design mix cement concrete of M25 grade (with a minimum cement content of 360 kg per cu.m) for reinforced concrete structural elements under controlled water cement ratio with plasticiser using 20mm and downgraded metal including form work, but excluding cost of steel reinforcement. G floor Precast slab

Providing and laying in position machine batched, machine mixed and machine vibrated design mix cement concrete of M25 grade (with a minimum cement content of 360 kg per cu.m) for reinforced concrete structural elements under controlled water cement ratio with plasticiser using 20mm and downgraded metal including form work, but excluding cost of steel reinforcement. G floor Roof Beams in Stilt Floor (Ready mix concrete)

Providing and laying in position machine batched, machine mixed and machine vibrated design mix cement concrete of M25 grade (with a minimum cement content of 360 kg per cu.m) for reinforced concrete structural elements under controlled water cement ratio with plasticiser using 20mm and downgraded metal including form work, but excluding cost of steel reinforcement. G floor Roof slab (Ready mix concrete)

Providing and laying in position machine batched, machine mixed and machine vibrated design mix cement concrete of M25 grade (with a minimum cement content of 360 kg per cu.m) for reinforced concrete structural elements under controlled water cement ratio with plasticiser using 20mm and downgraded metal including form work, but excluding cost of steel reinforcement. G floor Staircase waist slab

Providing and laying in position machine batched, machine mixed and machine vibrated design mix cement concrete of M25 grade (with a minimum cement content of 360 kg per cu.m) for reinforced concrete structural elements under controlled water cement ratio with plasticiser using 20mm and downgraded metal including form work, but excluding cost of steel reinforcement. G floor Lintel in SF

Providing and laying in position machine batched, machine mixed and machine vibrated design mix cement concrete of M25 grade (with a minimum cement content of 360 kg per cu.m) for reinforced concrete structural elements under controlled water cement ratio with plasticiser using 20mm and downgraded metal including form work, but excluding cost of steel reinforcement. G floor Sun shade and loft

Providing and laying in position machine batched, machine mixed and machine vibrated design mix cement concrete of M25 grade with a minimum cement content of 360kg per cu.m for reinforced concrete structural elements under controlled water cement ratio with plasticiser using 20mm and downgraded metal including form work, but excluding cost of steel reinforcement for First Floor. RCC Column

Providing and laying in position machine batched, machine mixed and machine vibrated design mix cement concrete of M25 grade with a minimum cement content of 360kg per cu.m for reinforced concrete structural elements under controlled water cement ratio with plasticiser using 20mm and downgraded metal including form work, but excluding cost of steel reinforcement for First Floor. Lintel

Providing and laying in position machine batched, machine mixed and machine vibrated design mix cement concrete of M25 grade with a minimum cement content of 360kg per cu.m for reinforced concrete structural elements under controlled water cement ratio with plasticiser using 20mm and downgraded metal including form work, but excluding cost of steel reinforcement for First Floor. Sun shade

Providing and laying in position machine batched, machine mixed and machine vibrated design mix cement concrete of M25 grade with a minimum cement content of 360kg per cu.m for reinforced concrete structural elements under controlled water cement ratio with plasticiser using 20mm and downgraded metal including form work, but excluding cost of steel reinforcement for First Floor. Roof Beams (Ready mix concrete)

Providing and laying in position machine batched, machine mixed and machine vibrated design mix cement concrete of M25 grade with a minimum cement content of 360kg per cu.m for reinforced concrete structural elements under controlled water cement ratio with plasticiser using 20mm and downgraded metal including form work, but excluding cost of steel reinforcement for First Floor. Roof slab (Ready mix concrete)

Supplying and fabricating and placing in position of MS/RTS steel reinforcement for RCC works including labour for cutting , bending , tying and fixing in position as per specification including cost of all materials, lead, lift, labour, cost of binding wire etc.comlete

Brick work in CM 1:5 (one cement & five sand) using Fly Ash bricks of size 230*110*70mm including finishing, curing etc. complete complying with standard specification Foundation & basement

Brick work in CM 1:4 (one cement & four sand) for partition wall 115mm thick, using Fly ash bricks of size 230*110*70mm including finishing, curing etc.complete complying with standard specification G Floor

Brick work in CM 1:5 (one cement & Six sand) using Fly Ash bricks of size 230*110*70mm including finishing, curing etc. complete complying with standard specification - Super structure G floor

Brick work in CM 1:5 (one cement & Six sand) using Fly Ash bricks of size 230*110*70mm including finishing, curing etc. complete complying with standard specification - Super structure Terrace cum First Floor

Providing cornice and architectural elevation with Brick work in C.M.1:4 using Fly Ash brick of size 9" * 4 1/2" *3 " and cement mortar bands as per drawing and as directed by the Engineer at site, at all levels including cost of all materials, labour etc. complete.

Providing grooves of 25mm in the plastering for architectural elevation works

Supplying and laying in spun pipe 230mm dia in bet. Cable duct crossing portion including cost of all materials, labour etc complete

Plastering in cm 1:3 mix 12mm thick for bottom of roof slab, bottom and sides of sunshade partition walls etc. including cost of all materials, lead, lift, watering, curing etc complete

Plastering with cm 1:5 mix using 20mm thick for outside walls including cost of all materials,labour,lead, lift etc complete

Plastering with cm 1:3 mix using 20mm thick with water proofing chemical for car park, plinth protection, water tank etc including cost of all materials, labour, lead, lift etc complete

Providing horizontal / vertical decorative mortar bands in CM 1:3, 20mm thick to uniform level and neat finish including cost of all materials, scaffolding, lead, lift etc. complete. 150mm width

Providing horizontal / vertical decorative mortar bands in CM 1:3, 20mm thick to uniform level and neat finish including cost of all materials, scaffolding, lead, lift etc. complete. 100mm width

Providing horizontal / vertical decorative mortar bands in CM 1:3, 20mm thick to uniform level and neat finish including cost of all materials, scaffolding, lead, lift etc. complete. 75mm

Supplying and fixing MS grill gates, MS grills, name board, hand rail, ladder etc. at various levels as per approved drawing using channel, square rods, ornamental grill parts and flats including fixing in position with suitable hold-fast locking arrangements etc. complete as per standard specification.

Supplying and fixing UPVC (Un-Plasticized Polyvinyl Chloride) Windows of casement type (open) from the profile the size of outer frame 60mm x 58mm and shutter profile are reinforcement with GI/1mm 125GSM and 100% corrosion free, the profiles are multi chambered sections with wall thick of 2mm. The EPDM rubber (black colour) covered with over all the edges of frame and shutter the shutter will be provided with Espag multi power point locks and also it operates as handle. The corners and joints should be welded and cleaned. Radiations free pin headed plain or brown colour glass 4mm thick should be provided to the shutter and it should not allow leakage of water even at most ranging storms and should have key lockable action, security protective hinges, strong locking systems and as per size for arresting noise and energy loss. The connecting mechanism between sash and outer frame that enables opening of the window. The window should be fixed to the wall with 100% packing with screws and silicon packing all round the frames. The window should be got approved from the Engineer-In-Charge before use on work.

Supplying and fixing UPVC (Un-Plasticized Polyvinyl Chloride) Fixed & Louvered Ventilators of from the profile the size of outer frame 60mm x 58mm and shutter profile size of 60 x 78mm both profiles are reinforced with GI/1mm 125GSM and 100% corrosion free, the profile are multi chambered sections with wall thick of 2mm. The EPDM rubber (black colour) covered with all over the edges of frame and shutter. The corners and joints should be welded and cleaned. Radiations pin headed glass 4mm thick should be provided in the louvers. The ventilators have provisions for fixing exhaust fan of suitable size. The window should be fixed to the wall with 100% packing with screws and silicon packing all round the frames. The ventilator should be got approved from the Engineer-In-Charge before use on work.

Supplying & fixing CW doors with outer frame of size 100x75 mm of Kongu/Padak/Vengai scantlings and door shutters should be Water Proof Solid core flush shutters with teak ply on both side with teak wood lipping alround 35mm thick with necessary adhesive and CP screws complying with standard specification. The rate inclusive of three coats of best quality varnish but including cost of furniture fittings such as 300 mm tower bolt 2 Nos. 200 mm tower bolt 1no. 300mm aldrop 1No. Aluminium Ornamental handle 2 Nos. and 1No. door stopper etc. complete. CW door with Shutter

Supplying & fixing CW doors with outer frame of size 100x75 mm of Kongu/Padak/Vengai scantlings and door shutters should be Water Proof Solid core flush shutters with teak ply on both side with teak wood lipping alround 35mm thick with necessary adhesive and CP screws complying with standard specification. The rate inclusive of three coats of best quality varnish but including cost of furniture fittings such as 300 mm tower bolt 2 Nos. 200 mm tower bolt 1no. 300mm aldrop 1No. Aluminium Ornamental handle 2 Nos. and 1No. door stopper etc. complete. UPVC Solid panelled door with frame

Supplying and fixing in position of hydraulic door closer heavy duty using Aluminium Extruded section body tubular type universal with ISI mark double speed adjustment like Hardwin, Gazal or equivalent quality including cost of all material, lead, labour etc. complete.

Supplying and fixing in position of Sun control film in glazed windows of approved quality and brand including cost of all materials, lead, labour etc.complete.

Supply, fabrication , fixing in position of Collopsible gate for stair case using MS flats, wheels,etc as per standard specification including cost of all materials ,lead, labour etc.complete

Supplying and erecting pull and push type rolling shutter with ISI make of approved size and section using 18 GI sheet. The shutter shall be painted with one coat of red oxide primer and the rate is inclusive of hood covers, transportation charges etc.,

Supplying and fixing in position of Alu. Anodised Partition with 62x38x2mm extruded box section at bottom vertical and horizontal members. The vertical member are spaced at 90 cm c/c and to horizontal members are spaced at 1.2M, 2.1M and 2.4M height the bottom covered with 12mm thick MDF exterior grade and the top and middle panels should be fixed at 5.50mm thick glass with necessary glassing clips , rubber beading etc. including necessary dismantling holes in RCC Columns ,beams, masonry wherever necessary with power drill to the extent required and made good to the original condition after fixing as directed by the engineer at site. All the al.section should be anodised to 15 microns as per ISI specification 1868/1962.

Supplying and fixing at anodized aluminium door using 101.60x44.45x2.10 mm @1.608 kg/m box section for outer frame. 53.70x44.45x2.30 @ 1.238 kg/m door vertical and top 83.50x44.45x2.4mm box section for bottom panels with 9mm thick regular grade pre laminated particle board & top panel with 5.5mm thick clear glass including cost of alum. Clips rubber beedings alum. Fixtures such as tower bolt, pivot brass mortice lock handle,with hydralick Door closer etc. of approved quality including cost of all materials, labour, leads, lift etc. complete (1.00mx2.20msize single leaf)

Paving the control room floor with rectified vitrified core endura grey coated floor tiles (Industrial type floor of johnson endura make , quality, colour and shade as directed by the engineer at site) of size 600 mm x 600mmx12mm in all floors over a base layer of cement mortar 1:3 (one cement and three sand) 20mm thick laid in-situ and pointed with same coloured cement mortar neatly finished as per standard specification .

Paving the floor with acid resistant tiles (quality, colour and shade as directed by the engineer at site) of size 305 mm x 305mm x 6 mm in battery room over a base layer of cement mortar 1:3 (one cement and three sand ) 20mm thick laid in-situ and pointed with same coloured cement

Dadooing walls with glazed tiles of best approved quality of make Johnson, Nitco, Euro of size 300x200 mm over cm 1:2, 12mm thick including cost of all materials, labour, lead, lift etc., complete (Dadooing with printed design colour glazed tiles of size 300mm x 200mm x 6mm)

Flooring with approved spartec ceramic non-slippery tiles 300x300mm size of approved Quality, design & colour (Johnson or equivalent make)laid in cement mortar 1:3 -20mm thick including pointing with same coloured cement using 0.4kg/sqm, finishing the joints, including cost of all materials, labour, lead, lift, etc. complete

Finishing the top of floor with Granolithic Finish with CC 1: 2: 3 (one cement Two sand & three HBS jelly) 50 mm thick using chips of grade 10 mm and below and rubbed smoothly

Providing weathering course with weathering proof cooling white tiles of size 25x25x2cm. Embeded in CM 1:3 12mm thick & pointed with same mortor mixed with crude oil 10% weight of cement used over a bed of brickjelly, lime concrete of 80mm thick with ratio of 32:12.5 cft, (no sand) with the required slope and beaten with wooden beaters including cost of all materials, curing, etc., complete.

Paving the approach to building, sides of roads, between building and setback area with Pave-it Rubber Moulded Hydraulic Pressed Paver interlocking block of 83mm thick of approved quality and colour over 100mm thick bed of filling sandcompacting properly with surface vibrator finishing neatly including cost of all materials, labour, T&P, lead, lift etc. complete.

Supplying and erection of 2.0HP Texmo/ Kirloskar/ Sharp/ Suguna make jet pump with all accessories, suitable L&T/ Siemens starter, L&T main switch, fuse, foot valve, etc. including cost of all materials as directed by the Engineer at site, commissioning etc. complete. for Borewell.

Supplying and erection of 3.0 HP Texmo/ Kirloskar / Sharp/ Suguna make Monoblock pump with all accessories, suitable L&T/ Siemens starter, L&T main switch, fuse, foot valve, etc. including cost of all materials as directed by the Engineer at site, commissioning etc. complete. (For Sump water)

Supplying and fixing of wash basin of size 550*400mm with all accessories of approved quality Parryware /Hindware including cost of wash basin with 15mm CP Pillar cock fixing using rag bolt and nut 15mm dia nylon connection hose and outlet using 32mm dia pipe waste coupling waste pipe water pipe for outlet including 15mm control wheel valve, 15mm dia brass nipple etc. complete as per standard specification.

Supply and fixing in position of Indian make white/ Colour glazed earthen ware lipped mouth flat back urinal basin of best approved quality of size 450mm with GI pipe connection to suitable length ,32mm bell mouthed PVC connection ,20mm dia GM wheel valve fixing the urinal to the wall including cost of all material,labour etc.complete.

Supplying and fixing in position 15mm dia brass CP screw down tap / Pillar tap (heavy duty) of approved make conforming to BIS specifications and quality including cost of shellac, thread, etc., complete complying with standard specification and including cutting and threading wherever necessary. (Taps should be got approved by the Executive Engineer before use on the works)

Supplying and fixing in positon Indian Water Closet (Oriya type) of size 580 x 440mm white glazed earthern ware of approved quality and brand with "P" or "S" trap conforming to BIS with sand cushion and forming flooring alround the closet using 40mm broken brick jelly in lime concrete 1:2:5 (One lime, Two sand and Five brick jelly) 100mm thick and finishing the top to the required slope and including giving necessary connection to CI soil pipes (including the cost of 100mm dia CI pipe for a length of 600mm) by dismantling brick masonry wall / reinforced cement concrete roof / floor slab and making good the dismantled portion to the original condition with leakages etc., complete complying with standard specifications and as directed by the departmental officers. (The water closet should be got approved by the Executive Engineer before use on works).

Supplying and fixing in position white / colour glazed European Water Closet of best quality and approved make with 100 mm "P" or "S" trap connecting with CI pipe of 100mm dia / PVC pipe of 110mm dia, double flapped rigid PVC black seat and seat cover with CP brass hinges and good quality CP Health faucets including cost of white cement, cement for packing, spun yarn, teak wood plugs, brass screws, etc., including supplying and fixing 10 litres capacity PVC / 12.5 litres capacity porcelin low level flushing tank with a pair of CI brackets, etc., complete with all fittings such as 15mm brass ball valve with polythene float with brass handle, union, coupling connected by means of 40mm white PVC flush hand using Indian adopter joint including all internal fittings..... such as 15mm brass connections, 15mm GM wheel valve, 15mm brass nipple (2 Nos.), 15mm nylon connection, TW plugs, screws and also giving necessary connection to the PVC pipe including cost of 600mm length of 110mm dia PVC pipe and painting the CI brackets with 2 coats of approved paint over one coat of red oxide primer, dismantling the masonry and re-doing the dismantled masonry to original condition etc. complete complying with standard specifications. (The EWC and flushing tank wiht all accessories should be got approved by the Executive Enginer before use on works)

Supplying and fixing white marble stone of size 600*1200mm, 20mm thick for partition to urinals including cost of all materials , lead lift,etc complete.

Supplying and fixing position CI Nahani Trap / Floor Trap of the following sizes with best stainless steel gratings of approved brand and quality, fixed over a bed of brick jelly lime concrete 1:2:5 (One part of lime, two part of sand and five part of 40mm gauge brick jelly) and finished with Cement Mortar 1:3 (One Cement, Three sand) including dismantling masonry works wherever found necessary and making good the dismantled portions to the original condition and giving connection to the CI / PVC pipes, etc., complete complying with standard specification. (The Nahani Trap should be got approved by the Executive Engineer before use on works)

Supplying and fixing in position RCC Pre-fabricated Manhole covers 450X450 of best approved quality and as per standard specification etc. complete

Supplying and fixing in position CI manhole covers with CI frames (Heavy duty) of size 60cm x 60cm of best approved quality as per standard specification etc., complete compying with standard specifications

Supplying and fixing in position Indian make bevelled edge mirror of approved quality and brand PVC / Fibre Glass framed 600 x 450 x 5.5mm thick mirror, shelf type with hard board backing of approved colour fixed with brass screws, rawl plug, etc., complete complying with standard specification. (The mirror should be got approved by the Executive Engineer before use on woks)

Supplying and fixing approved best quality brass CP towel rail 600mm long and 20mm dia with brackets of same materials including cost of teak wood plugs and CP screws, etc., complete complying with standard specifications. (The tower rail should be got approved by Executive Engineer before use on works).

Supplying and fixing best approved best quality brass CP soap tray of size 150 x 150mm including cost of teak wood plugs, brass screws, etc., complete complying with standard specifications. (The soap tray should be got approved by Executive Engineer before use on works).

Supplying and fixing in position CP shower rose with CP stop cock arrangement of size 15mm dia inlet and 100mm outlet to the pipe line with necessary cutting, threading and jointing using shellac etc., complete complying with standard specification and as directed by the departmental officers (The CP shower rose should be got approved by the Executive Engineer before use on works).

Supplying and fixing in position CP bib cock of size 15mm dia with necessary cutting, threading and jointing using shellac etc., complete complying with standard specification and as directed by the departmental officers (The CP bib cock should be got approved by the Executive Engineer before use on works).

Providing and fixing testing and commissioning of PVC pipe for internal soil, waste & vent to IS:13592 of SWR quality, 4kg /sq.cm, including all fittings like tees, elbows, bends, collars, coupling, etc jointing with rubber ring / solvent cement followed by application of leak proof adhesive like FRP paste laid on floors inside the toilets to the required slope including making necessary bores in walls / foundations / concrete slab as applicable, making good the bores with CM 1:3 or cement concrete as applicable, curing etc., complete. Dia 6"

Providing and fixing testing and commissioning of PVC pipe for internal soil, waste & vent to IS:13592 of SWR quality, 4kg /sq.cm, including all fittings like tees, elbows, bends, collars, coupling, etc jointing with rubber ring / solvent cement followed by application of leak proof adhesive like FRP paste laid on floors inside the toilets to the required slope including making necessary bores in walls / foundations / concrete slab as applicable, making good the bores with CM 1:3 or cement concrete as applicable, curing etc., complete. Dia 4"

Providing and fixing testing and commissioning of PVC pipe for internal soil, waste & vent to IS:13592 of SWR quality, 4kg /sq.cm, including all fittings like tees, elbows, bends, collars, coupling, etc jointing with rubber ring / solvent cement followed by application of leak proof adhesive like FRP paste laid on floors inside the toilets to the required slope including making necessary bores in walls / foundations / concrete slab as applicable, making good the bores with CM 1:3 or cement concrete as applicable, curing etc., complete. Dia 3"

Providing and fixing testing and commissioning of PVC pipe for internal soil, waste & vent to IS:13592 of SWR quality, 4kg /sq.cm, including all fittings like tees, elbows, bends, collars, coupling, etc jointing with rubber ring / solvent cement followed by application of leak proof adhesive like FRP paste laid on floors inside the toilets to the required slope including making necessary bores in walls / foundations / concrete slab as applicable, making good the bores with CM 1:3 or cement concrete as applicable, curing etc., complete. Dia 1-1/2"

Providing ,fixing, testing and commissioning of PVC soil, waste, vent and rain water pipe confirming to IS 13592 of SWR quality pressure rates as mentioned below, including all fittings, like Bends, Tees, Elbows, Collars, junction, inspection doors, cowls, offsets, access pipes, jointing with rubber ring followed by application of leak proof adhesive like FRP paste, fixed to wall with properly fabricated MS bracket of suitable size, GI 'U' clamps with bolts, nuts and GI washers complete, for soil and waste pipe lines laid vertically in shafts. Dia 6" (6kg/sq.cm)

Providing ,fixing, testing and commissioning of PVC soil, waste, vent and rain water pipe confirming to IS 13592 of SWR quality pressure rates as mentioned below, including all fittings, like Bends, Tees, Elbows, Collars, junction, inspection doors, cowls, offsets, access pipes, jointing with rubber ring followed by application of leak proof adhesive like FRP paste, fixed to wall with properly fabricated MS bracket of suitable size, GI 'U' clamps with bolts, nuts and GI washers complete, for soil and waste pipe lines laid vertically in shafts. Dia 4" (4kg/sq.cm)

Providing ,fixing, testing and commissioning of PVC soil, waste, vent and rain water pipe confirming to IS 13592 of SWR quality pressure rates as mentioned below, including all fittings, like Bends, Tees, Elbows, Collars, junction, inspection doors, cowls, offsets, access pipes, jointing with rubber ring followed by application of leak proof adhesive like FRP paste, fixed to wall with properly fabricated MS bracket of suitable size, GI 'U' clamps with bolts, nuts and GI washers complete, for soil and waste pipe lines laid vertically in shafts. Dia 3" (4kg/sq.cm)

Providing & fixing of UPVC pipe with fittngs like tees, elbows, bends, unions, coupling, reducer tees, collars etc. The work shall include cutting jointing with solvent cement pressure testing the joints / pipeline for 10 kg/sq.cm hydraulic pressure, for 2 hours etc. making holes, including chasing in solid block masonry walls with groove cutting machine to required width and depth, making bores in walls, foundations and RCC slabs, making good the walls and bores in CM 1:3 as applicable clearing the debris, grouting of concealed pipes, MS hooks for fixing pipes and making good the walls and floors. UPVC pipe 40mm dia

Providing & fixing of UPVC pipe with fittngs like tees, elbows, bends, unions, coupling, reducer tees, collars etc. The work shall include cutting jointing with solvent cement pressure testing the joints / pipeline for 10 kg/sq.cm hydraulic pressure, for 2 hours etc. making holes, including chasing in solid block masonry walls with groove cutting machine to required width and depth, making bores in walls, foundations and RCC slabs, making good the walls and bores in CM 1:3 as applicable clearing the debris, grouting of concealed pipes, MS hooks for fixing pipes and making good the walls and floors. UPVC pipe 32mm dia

Providing & fixing of UPVC pipe with fittngs like tees, elbows, bends, unions, coupling, reducer tees, collars etc. The work shall include cutting jointing with solvent cement pressure testing the joints / pipeline for 10 kg/sq.cm hydraulic pressure, for 2 hours etc. making holes, including chasing in solid block masonry walls with groove cutting machine to required width and depth, making bores in walls, foundations and RCC slabs, making good the walls and bores in CM 1:3 as applicable clearing the debris, grouting of concealed pipes, MS hooks for fixing pipes and making good the walls and floors. UPVC pipe 25mm dia

Providing & fixing of UPVC pipe with fittngs like tees, elbows, bends, unions, coupling, reducer tees, collars etc. The work shall include cutting jointing with solvent cement pressure testing the joints / pipeline for 10 kg/sq.cm hydraulic pressure, for 2 hours etc. making holes, including chasing in solid block masonry walls with groove cutting machine to required width and depth, making bores in walls, foundations and RCC slabs, making good the walls and bores in CM 1:3 as applicable clearing the debris, grouting of concealed pipes, MS hooks for fixing pipes and making good the walls and floors. UPVC pipe 20mm dia

Providing & fixing of UPVC pipe with fittngs like tees, elbows, bends, unions, coupling, reducer tees, collars etc. The work shall include cutting jointing with solvent cement pressure testing the joints / pipeline for 10 kg/sq.cm hydraulic pressure, for 2 hours etc. making holes, including chasing in solid block masonry walls with groove cutting machine to required width and depth, making bores in walls, foundations and RCC slabs, making good the walls and bores in CM 1:3 as applicable clearing the debris, grouting of concealed pipes, MS hooks for fixing pipes and making good the walls and floors. HDPE pipe 32mm dia 10 Kg/Sq.cm for Borewell

Providing & fixing of UPVC pipe with fittngs like tees, elbows, bends, unions, coupling, reducer tees, collars etc. The work shall include cutting jointing with solvent cement pressure testing the joints / pipeline for 10 kg/sq.cm hydraulic pressure, for 2 hours etc. making holes, including chasing in solid block masonry walls with groove cutting machine to required width and depth, making bores in walls, foundations and RCC slabs, making good the walls and bores in CM 1:3 as applicable clearing the debris, grouting of concealed pipes, MS hooks for fixing pipes and making good the walls and floors. HDPE pipe 25mm dia 10 Kg/Sq.cm for Borewell

Supplying and fixing GM wheel valve of approved brand (leader) ISI quality including cost of all materials, labour etc. complete 32mm

Supplying and fixing GM wheel valve of approved brand (leader) ISI quality including cost of all materials, labour etc. complete 25mm

Supplying and fixing GM wheel valve of approved brand (leader) ISI quality including cost of all materials, labour etc. complete 20mm

Supplying and fixing of PVC pipe ISI branded and approved quality as indicated below for water line , sanitory line etc.including cost of PVC special , and all other materials etc.complete as per standard specification. PVC Pipe 160mm dia. 6kg/ sq.cm for bore well

Supplying and fixing of PVC pipe ISI branded and approved quality as indicated below for water line , sanitory line etc.including cost of PVC special , and all other materials etc.complete as per standard specification. PVC Pipe 160mm dia. 6kg/ sq.cm for bore well strainer pipe with slotted holes

Drilling borewell in all kinds of soil 170 mm dia using rotary drilling power driven/ hand driven equipments including hire charges for equipment, bentonite solution, labour etc. complete

Supplying and filling with pebbles for annular space between strainer pipe and earth surface including cost of all materials, lead, lift etc. complete.

Flushing the borewell with power rotary flushing equipement including mobilisation and demobilisation etc. complete.

Supply and erection of RCC pre cast well rings of dia 1200mm, 300mm height and 50mm thick for construction of Rainwater Harvesting tank, Septic tank and Soak pit including cost of well rings, brick jelly, stone jelly 40, 20, 12, 10 mm and sand, etc., lead, lift, erection charges, labours etc., complete, as per direction and specification. Supply and erection of well rings 1200mm dia for Rain water harvesting, Septic tank and Soak pit.

Supply and erection of top cover suitable for 1200 mm dia well ring

Supply and erection of RCC well rings For Exhaust fan rings 450mm dia including cost of well rings, brick jelly, stone jelly 40, 20, 12, 10 mm and sand, etc., lead, lift, erection charges, labours etc., complete, as per direction and specification.

Supplying and fixing of SINTEX pvc water tank of 1000 litres capasity with necessary specials and fittings including cost of all materials , lead lift etc complete

Providing and applying minimum 20mm thick double coat plaster on concrete/masonry surface, not exceeding 50mm thickness in CM 1:5 ratio including mixing of water proofing components CICO NO - 1 (normal setting integral water proofing compound) or other approved equivalent make compound to the required proportion, finished to the appropriate slope as per drawing, including watering and curing and complete with all necessary scaffolding, equipments, tools and consumables.

White washing with freshly burnt shell lime white in colour in all floors including cost of lime and other materials brushes scaffolding charges etc.complete complying with standard specification and as directed.

Painting 2 coats with approved Plastic Emulsion paint over one priming coat of plastic emulsion paint over cement plastered wall surface, ceiling and other new surface and including cleaning ,preparing the surface and curing etc.complete.

Colour washing 2 coats with approved Emulsion paint over one priming coat over cement plastered wall surface applying wall putty, cleaning with sand paper , including cleaning ,preparing the surface cost of all labours to work at all levels, all materials, Scaffolding etc.complete.

Colour washing 2 Coats over a base coat of primer using Exterior weather coat using Asian APEX or Equivalent of approved Brand,quality and colour for outer wall surfaces for all floors including cost of all labours to work at all levels cost of materials brushes scaffolding charges etc. complete complying with standard specification and as directed.

Painting new wood work with two coats of synthetic enamel paint of approved quality and colour over a priming coat including cost of all materials etc complete.

Painting new iron works with two coats synthetic enamel paint over one coat of primer including cost of all materials, lead, lift, etc complete.

Providing Heritage flaks finish for the exterior surface of building of approved colour at all elevation including cost of all materials, lead, lifts, labour, Scaffolding, equipments, sprayer, tools and mixed properly as per the manufactures recommedation, apply and finish properly etc complete.

Dismantling the following items met with below ground level during execution including labour, tools etc. complete. Dismantling PCC

Dismantling the following items met with below ground level during execution including labour, tools etc. complete. Dismantling RCC

Dismantling the following items met with below ground level during execution including labour, tools etc. complete. Dismantling brick/ stone masonry in cement mortar

Manufacturing, Supplying and Fixing of Stainless Steel Hand rails for staircase using 50mm dia 304L Grade Stainless Steel pipe of 1.60mm thick at required locations to a height of 900mm from finished floor level welded to 38mm dia Stainless Steel pipe post of 1.00mm thick as vertical at 900mm centre with 2 Nos. of 25mm dia intermediate horizontal stainless steel pipe of 1.60mm thick in between. The vertical pipe has to be welded to the 100 X 100 X 6mm MS base plate encased in the base concrete. The rate is inclusive of the charges for cutting, bending, welding, grinding, polishing, conveyance, electrical charges, etc. complete

Providing 300mm dia flower pots containing green plants as directed by the Engineer

Providing two legged scaffolding using 15cm dia casuarinas post of 4m over all length (3m height + 0.5m Projection + 0.5m into the ground) the distance between the two rows being 1.25m and the spacing of post being 2.0m in both the rows with two horizontal post with 0.5m Overlap on either side and braces at 2.0m center to center including longitudinal and transeverse middle braces to step up and provding a platform with country wood planks of 40mm thick and 1m width, etc., in a complete from using coil and nails.

Turfing on slope including cost of sand, gravel mix in 1:1 for a depth of 0.15 m and red earth, sand and cow dung mix in 1:1:1 for a depth of 0.15 m and pitching of Korean grass including cost of all materials, watering, lead, lift, labour and T & P, etc., complete.

Supplying and fixing fine polished cuddapah slab of following thickness for cup-board arrangements including laying to correct alignment with necessary cement mortar and black powder etc, complete complying with standard specification and as direct.

Providing inspection chamber of size 0.6x0.6 (Inner size) to a max depth of 1.20m with CI manhole cover including all cost of materials, lead, lift etc complete.

Providing shoring and shuttering during earth work excavation and concreting including cost of all materials,labour, lead,lift etc complete.

Providing expansion joint for road concrete as per specification in both direction using prevalid aspheltics pad 20 mm thick to full width and depth of 150mm thick plastering with CM 1:3, 20 mm thick including cost of cement, all materials, labour, curing, all leads, and lifts, etc., complete.as per standard specification.

Dewatering during excavation and concreting by using 5hp deisel engine withone operator cost of oil, hire charges including labour for trnsport of all materials tools and plants etc., complete. (Observed data)

Supplying and fixing MS angle, channel,, MS rail, MS chequered plate, etc wherever required as directed by the Engineer as per standard specifcation MS CHANNEL

Supplying and fixing MS angle, channel,, MS rail, MS chequered plate, etc wherever required as directed by the Engineer as per standard specifcation MS Flats 60x8 mm for earth plate

Supplying and fixing MS angle, channel,, MS rail, MS chequered plate, etc wherever required as directed by the Engineer as per standard specifcation MS Chequred plate 8mm thick

Aluminum composite panel works:Designing the system for cladding the external wall with approved make of aluminum composite panels --- 4mm thick(0.5 mm thick aluminum sheet on top and bottom sandwiched with 3 mm thick core material of anti toxic low density polyethylene) in combinaton with solid and metallic colour panels, by using pre-assemble extruded aluminum sections/brackets and aluminium composite panel to withstand design wind pressure of 150 kg/sqm (Testing pressure shall be 1.5 times of the design wind pressure of 150 kg/sqm) conforming to IS 875-Part III. The system shall be designed to accomodate thermal movement of the aluminium framing system including supporting arrangements.Fastening devices and composite panel resulting from the exterior skin temperature from 15 to 85 deg.celcius.Interior skin temperature from 15 to 30 deg. celcius and to accomodate horizontal buiding movement of maximum 10 mm per bay and vertical movement of maximum 20 mm between floors and conforming that no aluminium members shall be visible from outside.

Supplying and fixing in position of Aluminium dye cast powder coated letters of various sizes and emblem in 12mm thick as per the requirement of Board including cost of all materials,aluminium letter, emblem, scaffolding etc. complete as directed by the engineer at site.TNEB Emblem

Supplying and fixing in position of Aluminium dye cast powder coated letters of various sizes and emblem in 12mm thick as per the requirement of Board including cost of all materials,aluminium letter, emblem, scaffolding etc. complete as directed by the engineer at site. 30 cm size letters

Supplying and fixing in position of Aluminium dye cast powder coated letters of various sizes and emblem in 12mm thick as per the requirement of Board including cost of all materials,aluminium letter, emblem, scaffolding etc. complete as directed by the engineer at site. 23cm size letters

Supplying and fixing in position of Aluminium dye cast powder coated letters of various sizes and emblem in 12mm thick as per the requirement of Board including cost of all materials,aluminium letter, emblem, scaffolding etc. complete as directed by the engineer at site. 15cm size letters

Supply and fixing 1 no 4 way Three phase and natural distribution board with insulator and 1 No.MCB of 6 amps each of standard company as approved by the engineer including cost of all materials, lead, lift, etc., complete.

Supply and fixing of 8 way single pole and neutral MCB sheet steel enclosure Distribution board 1No 32 Amps DB MCB as incoming and 6 Nos 6 Amps to 32 Amps SPMCB outgoing in flush with wall and making good of the concealed portion with earth connection only. The MCB DB and MCB's should be with ISI mark (Like Standard make).

Supplying and fixing of MCB four pole and nuetral link 35 to 63A capacity fitted with suitable flush board and 4 no. 16A/32 distribution MCB and provision for future including cost of all materials,labour, lead,lift, etc., complete

Supplying and fixing of panel board of good quality of size 0.90 x 0.60m including fixing 3 Nos. 32 Amps fuse carrier and 3 nos phase bulb with 3 nos batten holder and 3 nos 5 amps switch and 3 nos 52 amps fuse unit for arial fuse and in and out wiring in the panel and panal board to meter with 7 / 20 CTS wire and GI pipe of earthing as per TNEB standard specification including cost of materials, labour, lead, lifts, etc, complete.

Supply & run of 3 1/2 core 70 sq.mm. PVC Armoured UG Cable with all accessories from Main EB pillar box to EB meter.

Supply and laying of 4 x 6 sq.mm PVC armoured LTUG cable in a trench to be excavated at a depth of 0.75 metre putting 0.15 mt. Layer of sand and covering the cable completely with bricks and sand and refilling the earth to make good.

Supplying and providing wiring with 2 runs of 4 sq.mm PVC insulated copper wire alongwith 1.5 sq.mm PVC insulatd copper wire for earthing inside the PVC rigid conduit not less than 25mm width and 2mm thickness for running circuit main from DB to all Switch Boxes, motors and inverter. Neutral should not be looped.Neutral in back and earthing in green to be followed.

Wiring with 2x1.50 sq.mm PVC unsheathed copper multistand cable of 650v grade in suitable pvc rigid pipe in wall or ceiling with pvc accessories with TW switch box in flush with wall covered with hylum sheet of 3mm thick with painting of suitable colour with contineous earthwire connection of 14 swg tc wire for light points

Wiring with 2x1.50 sq.mm PVC unsheathed copper multistand cable of 1100v grade in suitable pvc rigid pipe in wall or ceiling with pvc accessories with TW switch box in flush with wall covered with hylum sheet of 3mm thick with painting of suitable colour with contineous earthwire connection of 14 swg tc wire for Fan points

Wiring with 2 x 1.5 sq mm ( 22/0.30) PVC insulated SC unsheathed copper conductor of 1100 V grade in suitable PVC rigid pipe on wall and ceiling with PVC accessories and with metal box 300 x 150 x 75 mm with 3 mm thick Hylem sheet and 5A FT switch and mounted on the wall surface for computer point (SD 27)

Wiring with two pair copper telephone cable in suitable conduit pipe in wall and terminated with socket for telephone jack with TW switch box in flush with wall covered with hylum sheet of 3mm thick for telephone point

Supplying of switch board and wiring 2 runs of 4sq.mm PVC insulated copper wire and for earthing and connection with 15Amps switch and socket combined with 15 Amps plug and MS switch box size 6"x4"x3" for Battery point . This includes cost of materials and labour charges.

Supplying and providing wiring to motor room points from motor to starter switch boxes using 2 runs of 4sq.mm pvc insulated copper wire along with 1.5 sq.mm PVC casing/ PVC pipe not lessthan 25mm width with 2mm wall thickness including cost of materials , labour charges , switch board of size 18"x12"x3" with 16Amps doublepole mainswitch and providing sufficient pace for providing and connections.

Supplying and fixing box type 4'-40w single flouresent fitting complete with copper choke and condenser 1 no 4'-40w tube with T.W. round block on wall or ceiling with pvc unsheated leads from terminals to the fittings

Supply and fixing of 2x4' 40 W Twin Mirror optic suspension type fitting (Philips / Crompton / Wipro) complete with louvers cover complete with copper choke and condensor with conduit pipe suspension, with PVC unsheathed Copper leads from the terminals to the fittings with flu. tubes.

Supply and fixing of 1400 mm sweep (56") AC ceiling fan complete with stepped electronic 300W regulator with 1metre down rod including fan clamp with side plates and cross arm of size 450 mm.

Supplying and fixing of 5 amps 3 pin socket in the exisitng switch including 3 pin top.

Supply and fixing of 5A / 15 A 3 Pin combined flush type wall socket with 15A flush type switch concealed in suitable MS Box in flush with wall and covered with 3 mm thick hylem sheet

Supply and fixing of 450 mm (18") sweep (light duty) AC exhaust fan complete with necessary wall opening and making good of the wall.

Supply and fixing of fancy glass shade and 40 W bulb for BH point.

Earthing as per the ISI specification with an earth electrode of 2.1mt class 'B' GI pipe of dia not less than 40mm, with copper earth plate of size 125mm x 50mm x 6mm, with necessary funneling arrangements with necessary masonry work and with 38mm RCC cover slab for the brick masonry .

Supplying and fixing of RCCB safe trip of appd LEGRAND , ISI make , 25amps with suitable box including cost of all materials labour, lead, lift, etc., complete as per standard specification.

Supplying and fixing of 60W LED Street Light Fitting of Street Light 6m height including cost of all materials, labour, lead, lift etc., complete, as per standard specification.

Supplying and fixing of water tight Bulk head fitting with guard and approved suitable make for incondescent lamp with guard and 100 w bulb.

Supplying and fixing musical quartz type Wall Clock of size 30 x30 cm of approved quality and colour including transport, fixing charges etc complete.

Supplying and fixing of 40mm dia. GI B class pipe for road crossing including cost of materials ,labour lead,lift etc

Supply and fixing of AC / DC 7 mm Buzzer / call bell suitable for 230 V 50 c/s single phase AC supply on suitable TW board with push switch (SD 105)

Supplying and fixing,testing & comissioning of Surface Mounted LED fittings for 100W LED with necessary connections etc.,of suitable for control room

Supplying and fixing, testing & commissioning of Mirror optical surface mounted light fitting with 2x2 36W LED Luminaire lamp and necessary fixing accessories of standard make and connections.

Supplying and fixing,testing & comissioning of 4W emergency light with rechargeable dry cell, necessary stand etc., by making connections through plug,

Supply steel furniture manufacture by 'TANSI' or any other ISI make including cost of all materials, labour, lead and lift etc., complete. sample to be approved by department Engineer Transporting and supply of steel table with on drawer and one cup-board of size 44"x24"x30" including cost of all labour,lead,lift etc complete

Supply steel furniture manufacture by 'TANSI' or any other ISI make including cost of all materials, labour, lead and lift etc., complete. sample to be approved by department Engineer Transporting and supply full arm steel 'S' type chair including cost of all labour, lead,lift etc complete

Supply steel furniture manufacture by 'TANSI' or any other ISI make including cost of all materials, labour, lead and lift etc., complete. sample to be approved by department Engineer Transporting and supply steel rack of 4 shelves (Open type) with 3 compartment of size 3'x1'x4' including cost of all labour, lead,lift etc complete

Supply steel furniture manufacture by 'TANSI' or any other ISI make including cost of all materials, labour, lead and lift etc., complete. sample to be approved by department Engineer Transporting and supply steel stool of size 1-1/4' x 1-1/4' including cost of all labour, lead, lift etc complete.

Supply steel furniture manufacture by 'TANSI' or any other ISI make including cost of all materials, labour, lead and lift etc., complete. sample to be approved by department Engineer Transporting and supply steel half bench of size 3-1/4' x 1-1/4' x 1-1/2' including cost of all labour, lead, lift etc complete.

Supply steel furniture manufacture by 'TANSI' or any other ISI make including cost of all materials, labour, lead and lift etc., complete. sample to be approved by department Engineer Transporting and supply Revolving chair including cost of all labour, lead, lift etc complete.

Supply steel furniture manufacture by 'TANSI' or any other ISI make including cost of all materials, labour, lead and lift etc., complete. sample to be approved by department Engineer Transporting and supply operator table 6'x5' including cost of all labour, lead, lift etc complete.

Supply steel furniture manufacture by 'TANSI' or any other ISI make including cost of all materials, labour, lead and lift etc., complete. sample to be approved by department Engineer Transporting and supply PVC ARMED CHAIR OF REPUTED MAKE including cost of all labour, lead, lift etc complete.

Supplying and fixing of angle with 18Kg sheet proper welding for various size of name board with holding post height 2m above the GL of angle 65x65x6mm and painting and lettering the name of office over the two coat of painting as the direction of site engineer including cost all brush, painting, labour, materials etc complete.

Supplying and fixing black granite stone Engraved Design detail and fixing in wall at entrance, Digital wall clock 2 Nos, floor coir mat 2000x600 for Entrance 1000x500 - 2 No. for office of approved make and quality including the cost of all materials, lead, lift, labour, etc., complete and as directed by the Dept. Engineer at site.

GST for bidders within TamilNadu

GST for bidders outside TamilNadu (IGST)

A.H.CONSTRUCTIONS

M.JAYAVEL

m/s Kumar and co

K RAJARAM

M/s.V.APPU ENTERPRISES

Dillibabu