MC and EW for development works and visitor amenities under NCF Phase-II at Shiv Temple, Deobaloda

Amount

Earth work in excavation by manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth lead upto 50 m and lift upto 1.5 m, as directed by Engineer-in- charge for toilet block.

Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 and for all lift for toilet block

Surface dressing of the ground including removing vegetation and in equalities not exceeding 15 cm deep and disposal of rubbish, lead up to 50 m and lift up to 1.5 m.All kinds of soil for toilet block. for toilet block

Supplying chemical emulsion in sealed containers including delivery as specified. Chlorpyriphos/ Lindaneemulsifiable concentrate of 20% for toilet block

Supplying and filling in plinth with sand under floors, including watering, ramming, consolidating and dressing complete for toilet block.

Diluting and injecting chemical emulsion for POST CONSTRUCTIONAL anti-termite treatment (excluding the cost of chemical emulsion) : Along external wall where the apron is not provided using chemical emulsion @ 7.5 litres / sqm of the vertical surface of the substructure to a depth of 300mm including excavation channel along the wall & rodding etc. complete: With Chlorpyriphos/ Lindane E.C. 20% with 1% concentration for toilet block.

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level.1:3:6 (1 Cement : 3 coarse sand (zone-III) : 6 graded stone aggregate 20 mm nominal size) for toilet block

Providing and fixing up to floor five level precast cement concrete string or lacing courses, copings, bed plates, anchor blocks, plain window sills, shelves, louvers, steps, stair cases, etc., including hoisting and setting in position with cement mortar 1:3 (1 Cement : 3 coarse sand),cost of required centering complete.1:1.5:3 (1 cement : 1.5 coarse sand : 3 graded stone aggregate 20 mm nominal size) for toilet block

Making plinth protection 50mm thick of cement concrete 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) over 75mm thick bed of dry brick ballast 40 mm nominal size, well rammed and consolidated and grouted with fine sand, including necessary excavation, levelling & dressing & finishing the top smooth for toilet block.

Random rubble masonry with hard stone in foundation and plinth including levelling up with cement concrete 1:6:12 (1 cement : 6 coarse sand : 12 graded stone aggregate 20 mm nominal size) upto plinth level with : Cement mortar 1:6 (1 cement : 6 coarse sand) for toilet block

Stone work, plain in copings, cornices, string courses and plinth courses, upto 75 mm thick in Cement mortar 1:6 (1 cement : 6 coarse sand), including pointing with white cement mortar 1:2 (1 white cement : 2 stone dust) with an admixture of pigment matching the stone shade. Red Sand Stone for toilet block

Centering & shuttering including strutting, propping etc. and removal of form work for: Suspended floors, roofs, landings, balconies and access platform for toilet block

Centering & shuttering including strutting, propping etc. and removal of form work for: Lintels, beams, plinth beams, girders, bressumers and cantilevers for toilet block.

Centering & shuttering including strutting, propping etc. and removal of form work for: Edges of slabs and breaks in floors and walls Under 20 cm wide for toilet block

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete above plinth level. Thermo- Mechanically Treated bars for toilet block

Providing and laying in position machine batched and machine mixed design mix M-25 grade cement concrete for reinforced cement concrete work, using cement content as per approved design mix, including pumping of concrete to site of laying but excluding the cost of centering, shuttering, finishing and reinforcement, including admixtures in recommended proportions as per IS: 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability as per direction of Engineer-in charge.“(Note :- Cement content considered in this item is @ 330 kg/cum.“Excess/ less cement used as per design mix is payable/recoverable separately).All works upto plinth level for toilet block

Providing and laying in position machine batched and machine mixed design mix M-25 grade cement concrete for reinforced cement concrete work, using cement content as per approved design mix, including pumping of concrete to site of laying but excluding the cost of centering, shuttering, finishing and reinforcement, including admixtures in recommended proportions as per IS: 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability as per direction of Engineer-in charge.“(Note :- Cement content considered in this item is @ 330 kg/cum.“Excess/ less cement used as per design mix is payable/recoverable separately).All works above plinth level upto floor V level for toilet block.

Brick edging 7cm wide 11.4 cm deep to plinth protection with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 including grouting with cement mortar 1:4 (1 cement : 4 fine sand) for toilet block.

Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for platforms, vanity counters, window sills , facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels.Raj Nagar Plain white marble/ Udaipur green marble/ Zebra black marble.Area of slab upto 0.50 sqm for toilet block

Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for platforms, vanity counters, window sills , facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels.Granite of any colour and shade.Area of slab over0.50 sqm for toilet block

Extra for fixing marble /granite stone, over and above corresponding basic item, in facia and drops of width upto 150 mm with epoxy resin based adhesive, including cleaning etc. complete for toilet block

Extra for providing opening of required size & shape for wash basin/ sink in platform, vanity counter and similar location in marble/ Granite/stone work, including necessary holes for pillar taps etc. including moulding, rubbing and polishing of cut edges etc.complete for toilet block

Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia& length ( hold fast lugs or dash fastener shall be paid for separately).Sal wood for toilet block

Providing and fixing glazed shutters for doors, windows and clerestory windows using 4 mm thick float glass panes, including ISI marked M.S. pressed butt hinges bright finished of required size with necessary screws.Second class teak wood.35 mm thick shutters for toilet block

Extra for providing frosted glass panes 4 mm thick instead of ordinary float glass panes 4 mm thick in doors, windows and clerestory window shutters. (Area of opening for glass panes excluding portion inside rebate shall be measured) for toilet block

Providing and fixing ISI marked flush door shutters conforming to IS :2202 (Part I) non-decorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters : 35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws for toilet block

"Extra for providing lipping with 2nd class teak wood battens 25 mm minimum depth on all edges of flush door shutters (over all area of door shutter to be measured) for toilet block

Providing and fixing M.S. grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc. including priming coat with approved steel primer all complete.Fixed to openings /wooden frames with rawl plugs screws etc for toilet block

Providing and fixing aluminum die cast body tubular type universal hydraulic door closer (having brand logo with ISI, IS : 3564, embossed onthe body, door weight upto 35 kg and door width upto 700 mm), with necessary accessories and screws etc. complete for toilet block

Providing and fixing Fiber Glass Reinforced plastic (FRP) Door Frames of cross-section 90 mm x 45 mm having single rebate of 32 mm x 15 mm to receive shutter of 30 mm thickness. The laminate shall be moulded with fire resistant grade unsaturated polyester resin and chopped mat. Door frame laminate shall be 2 mm thick and shall be filled with suitable wooden block in all the three legs. The frame shall be covered with fiber glass from all sides. M.S. stay shall be provided at the bottom to steady] the frame for toilet block

"30 mm thick Fiberglass Reinforced Plastic (F.R.P.) flush door shutter in different plain and wood finish made with fire retardant grade unsaturated polyester resin, moulded to 3 mm thick FRP laminate all around, with suitable wooden blocks inside at required places for fixing of fittings and polyurethane foam (PUF)/ Polystyrene foam to be used as filler material throughout the hollow panel, casted monolithically with testing parameters of F.R.P. laminate conforming to table - 3 of IS: 14856, complete as per direction of Engineer in- charge for toilet block

Providing & Fixing decorative high pressure laminated sheet of plain / wood grain in gloss / matt / suede finish with high density protective surface layer and reverse side of adhesive bonding quality conforming to IS : 2046 Type S, including cost of adhesive of approved quality.1.0 mm thick for toilet block

Providing and fixing aluminum handles, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade, with necessary screws etc. complete :125mm long for toilet block

Providing and fixing aluminum handles, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade, with necessary screws etc. complete .100mm long for toilet block

Providing and fixing stainless steel (SS 304 grade) adjustable friction windows stays of approved quality with necessary stainless steel screws etc. to the side hung windows as per direction of Engineer-in-charge complete for toilet block

Providing and fixing carbon steel galvanised ( minimum coating 5 micron) dash fastener of 10 mm dia double threaded 6.8 grade (yield strength 480 N/mm2), counter sunk head, comprising of 10 m dia polyamide PA 6 grade sleeve, including drilling of hole in frame , concrete/ masonry, etc. as per direction of Engineer-in-charge.10 x 80 mm for toilet block.

Providing and fixing stainless steel ( Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in-charge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.) for toilet block

Chequerred precast cement concrete tiles 22 mm thick in footpath & courtyard, jointed with neat cement slurry mixed with pigment to match the shade of tiles, including rubbing and cleaning etc. complete, on 20 mm thick bed of cement mortar 1:4 (1 cement: 4 coarse sand).Light shade pigment using white cement for toilet block

Kota stone slab flooring over 20 mm (average) thick base laid over and jointed with Grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete with base 1:4 (1cement : 4coarse sand).25 mm thick for toilet block

Kota stone slabs 20 mm thick in risers of steps, skirting, dado and pillars laid on 12 mm (average) thick cement mortar 1:3 (1 cement: 3 coarse sand) and jointed with grey cement slurry mixed with pigment to match the shade of the slabs, including rubbing and polishing complete. for toilet block

Extra for pre finished nosing in treads of steps of Kota stone/ sand stone slab for toilet block

Extra for Kota stone/ sand stone in treads of steps and risers using single length up to 1.05 metre for toilet block

"Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete for toilet block.

Providing and fixing Glass mossaic tiles at finished plain wall surface of size 20 mm x 20 mm x 4 mm in all colour, design , fixing in customize design as per direction of Engineer-in Charge. The glass mosaic tiles to be fixed on the wall surface with the help of approved adhesive applied at the rate of 2.5 kg per sqm and grouting of the same. The rate is inclusive of all operation, material and required pattern approved by Engineer-in Charge for toilet block

Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS : 15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), including grouting the joints with white cement and matching pigments etc., complete.Size of Tile 600x600 mm for toilet block

Providing and laying matt finished vitrified tile of size 100x100x16mm having water absorption less than 0.5% and conforming to IS: 15622 of approved make in all colours and shades in out door floors such as footpath, court yard multi models etc., laid on 20mm thick base of cement mortar 1:4 (1cement : 4 coarse sand) in all shapes & patterns including grouting the joints with white cement mixed with matching pigments etc. complete as direction of Engineer-in Charge for toilet block

Providing gola 75x75 mm in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 stone aggregate 10 mm and down gauge), including finishing with cement mortar 1:3 (1 cement : 3 fine sand) as per standard design :In 75x75 mm deep chase for toilet block

Making khurras 45x45 cm with average minimum thickness of 5 cm cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate of 20 mm nominal size) over P.V.C. sheet 1 m x1 m x 400 micron, finished with 12 mm cement plaster 1:3 (1 cement : 3 coarse sand) and a coat of neat cement, rounding the edges and making and finishing the outlet complete for toilet block

Providing and fixing on wall face unplasticised Rigid PVC rainwater pipes confirming to IS:13592 Type A including jointing with seal ring confirming to IS:5382 leaving 10 mm gap for thermal expansion.(I)single socketed pipes.100 mm diameter for toilet block.

Providing and fixing unplasticised PVC pipe clips of approved design to unplasticised - PVC rain water pipes by means of 50x50x50 mm hard wood plugs, screwed with M.S. screws of required length including cutting brick work and fixing in cement mortar 1:4 (1 cement : 4 coarse sand) and making good the wall etc. complete for toilet block

Providing and fixing to the inlet mouth of rain water pipe cast iron grating 15 cm diameter and weighing not less than 440 grams for toilet block

15 mm cement plaster on the rough side of single or half brick wall of mix : 1:6 (1 cement : 6 coarse sand) for toilet block.

6 mm plaster on cement concrete or reinforced cement concrete work with white cement based polymer modified self curing mortar of approved make as per the direction of Engineer-In Charge for toilet block

Extra for providing and mixing water proofing material in cement plaster work in proportion recommended by the manufacturers for toilet block.

Distempering with oil bound washable distemper of approved brand and manufacture to give an even shade :New work (two or more coats) over and including water tinnable priming coat with cement primer for toilet block.

Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade :Two or more coats on new work over an under coat of suitable shade with ordinary paint of approved brand and manufacture for toilet block

Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete for toilet block

Grading roof for water proofing treatment with Cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) for toilet block

Providing and applying integral crystalline slurry of hydrophilic in nature for waterproofing treatment to the RCC structures like retaining walls of the basement, water tanks, roof slabs, podiums, reservior, sewage & water treatment plant, tunnels/ subway and bridge deck etc., prepared by mixing in the ratio of 5 : 2 (5 parts integral crystalline slurry : 2 parts water) for vertical surfaces and 3 : 1 (3 parts integral crystalline slurry : 1 part water) for horizontal surfaces and applying the same from negative (internal) side with the help of synthetic fiber brush. The material shall meet the requirements as specified in ACI- 212-3R-2010 i.e by reducing permeability of concrete by more than 90% compared with control concrete as per DIN 1048 and resistant to 16 bar hydrostatic pressure on negative side.The crystalline slurry shall be capable of self-healing of cracks up to a width of 0.50mm. The work shall be carried out all complete as per specification and the direction of the engineer-in charge. The product performance shall carry guaranteed for 10 years against any leakage.For horizontal surface one coat @1.10 kg per sqm for toilet block

Provision for providing recess pointing with use of traditional mortar of racked joints for toilet block

Providing and fixing both face dressed stone work in Coursed rubble masonry of sand stone in superstructure above plinth level and upto floor five level in cement mortar 1: 4 (1 cement : 4 coarse sand) etc complete as per direction of Engineer in- charge for toilet block

Provision for providing and fixing of necessary fixtures to doors, windows and singnages etc., as directed by engineer in charge for toilet block i) P&F Signage for toilet doors of size300 X 600 mm as per engineer in charge.

ii) Providing & fixing Stainless steel heavy duty Sliding door bolt.The work shall be carried out all complete as per specification and the direction of engineer-in-charge

iii) Providing & fixing window SS towerbolt of dorset make model TS-1010 -10”.The work shall be carried out allcomplete as per specification and thedirection of engineer-in-charge.

iv) Providing & fixing door SS tower boltof dorset make model TS-610 -06”.The work shall be carried out allcomplete as per specification and thedirection of engineer-in-charge.

v) Providing and fixing SS hanging floor door stopper ISI marked a to required colour and shade with necessary screws etc. complete

vi) Providing & fixing SS door latch of dorset make or equivelent.The work shall be carried out all complete as per specification and the direction of engineer-in-charge.

Providing and fixing water closet squatting pan (Indian type W.C. pan) with 100mm sand cast Iron P or S trap, 10 litre low level white P.V.C. flushing cistern including flush pipe with manually controlled device (handle lever) conforming to IS:7231, Parryware/Hindware/Seabird/Orient (Coral) with all fittings and fixtures complete including cutting and making good the walls and floors wherever required. White Vitreous china Orissa pattern W.C. pan of size 580x440 mm with integral type foot rests for toilet block

Providing and fixing P.V.C. waste pipe for sink or wash basin including PVC waste fittings complete.Flexible Pipe for toilet block

Providing and fixing Stainless Steel A ISI 304 (18/8) sink as per IS: 13983 with C.I. brackets and stainless steel plug 40 mm, including painting of fittings and brackets, cutting and making good the walls wherever required:sink without drain board.610x510 mm bowl depth 200mm for toilet bloc

Providing and fixing white vitreous china extended wall mounting water closet of size 780x370x690 mm of approved shape including providing & fixing white vitreous china cistern with dual flush fitting, of flushing capacity 3 litre/ 6 litre (adjustable to 4 litre/ 8 litres), including seat cover, and cistern fittings, nuts, bolts and gasket etc complete for toilet block.

Providing and fixing CP Brass 32mm size Bottle Trap of bapproved quality & make and as per the direction of Engineer-in- charge for toilet block

Providing and fixing white vitreous china battery based infrared sensor operated urinal of approx. size 610 x 390 x 370 mm having pre & post flushing with water (250 ml & 500 ml consumption), having water inlet from back side, including fixing to wall with suitable brackets all as per manufacturers specification and direction of Engineer-in-charge for toilet block.

Provision for plumbing works of toilets, wash basin etc. complete with all necessary fittings and fixings and changing of sanitary items wherever necessary etc. for toilet block. i) Providing & fixing white viterous chinaBelow counter Oval Wash Basin size550 x 445 mm with C.P. brass pillartap of an approved design and make,CI/MS brackets, 32 mm C.P. brass waste of standard pattern, standardquality P.V.C. waste pipe. [EACH]

ii) Providing & fixing C.P. Brass health faucet for ablution with 1 meter long PVC tube, hand shower, couplings, wall hook and other accessories.

iii) Providing & fixing P&F white vitreouschina flat back half stall urinal of size460X350X260 mm with fittings,standard size C.P. Brass flush pipe,spreader with union and clamps (all in C.P. Brass) with waste fittings as perIS : 2556 and other couplings in CPbrass, inclusding painting and fittingsand cutting and making good thewalls and floors wherever required:

iv) Providing 40 mm dia. C.P.Brass bottletrap with 190 mm long wall connectionpipe in place of P.V.C. waste pipe forSink discharge

v) Providing fully automatic No Touch hand dryer of ABS body, suitable to operate on 220 V / 50 Hz AC power, 1650 Watt, having

vi) Providing and fixing of 600 mm longC. P. brass towel rail complete withC.P. brass brackets

vii) Providing and fixing CP Brass liquidsoap dispensor 109 mm wide, 125mm high and 112 mm distance fromwall of standard shape with bracketand all fittings of the same material of approved quality and colour.

viii) Providing & Fixing of required size ofbevelled edge mirror of superior glass(of approved quality) complete with4mm thick hard board ground fixed towooden cleats with C.P. brass screwsand washers complete.

ix) Providing & Fixing of stainless steel (SS-304) grab bar in Divyang toilet ofapproved side &shpae complete withfixing etc as per directed by engineer -in-charge.

x) Providing & Fixing of 12 mm thicktoughned glass of approved make ofsize ( 500 x 750) with fixed in wall withsilicon etc as per directed byengineer-in-incharge.

xi) Providing & Fixing 600 X 450 mmbevelled edge mirror of superior glass(of approved quality) complete with6mm thick hard board ground fixed towooden cleats with C.P. brass screwsand washers complete.

xii) Providing & fixing toilet paperholder.viterous china

xiii) Providing, fixing, jointing and testingin position of ISI marked UV stabilizedUPVC pipes for soil, waste, and vent,Type-B as per IS : 13592 suitable forrubber ring joints, including all neccessary specials and fittings(confirming to IS:14735) i.e. bends,tees, junctions (with or without doors),reducers, WC connectors, couplers,expansion joints / bellows, cowels, clamps, rubber rings, clean outs etc.fixing at wall/ ceiling/ floor levelsupported by clamp & hangers etc. Inconcealed / inside duct / under floor &basement ceiling / external work etc. including chase cutting as required,excavation and back filling in all kindof soils, suspended from floor underfalse ceiling or embedding the pipeslaid under floors / building in 75 mm. alround 1:2:4 cement concrete (1cement : 2 coarse sand : 4 gradedstone aggregate 20 mm nominal size)including cost of shuttering for propercompletion of the work, breaking and making good the walls and floors etc.after pipes have been duly laid andtested. The rubber ring shall confirmto IS:5382.The Pipes will besupported with threaded G I rods & Uclamps with nuts, washers etc on50x50x5 mm slotted angle. The costwill include all support arrangements. The work includes commissioning ofall pipes lines as per drawings andspecifications and as directed byengg-in-charge at site.110 mm dia(Wall Thickness - 3.2 to 3.8 mm)

xiv) Providing, fixing, jointing and testingin position of ISI marked UV stabilizedUPVC pipes for soil, waste, and vent,Type-B as per IS : 13592 suitable forrubber ring joints, including all neccessary specials and fittings(confirming to IS:14735) i.e. bends,tees, junctions (with or without doors),reducers, WC connectors, couplers,expansion joints / bellows, cowels,clamps, rubber rings, clean outs etc.fixing at wall/ ceiling/ floor levelsupported by clamp & hangers etc. Inconcealed / inside duct / under floor &basement ceiling / external work etc.including chase cutting as required,excavation and back filling in all kindof soils, suspended from floor underfalse ceiling or embedding the pipeslaid under floors / building in 75 mm.alround 1:2:4 cement concrete (1cement : 2 coarse sand : 4 gradedstone aggregate 20 mm nominal size) including cost of shuttering for propercompletion of the work, breaking andmaking good the walls and floors etc.after pipes have been duly laid andtested. The rubber ring shall confirmto IS:5382.The Pipes will besupported with threaded G I rods & Uclamps with nuts, washers etc on50x50x5 mm slotted angle. The costwill include all support arrangements.The work includes commissioning ofall pipes lines as per drawings andspecifications and as directed by engg-in-charge at site. 75 mm dia(Wall Thickness - 3.2 to 3.8 mm)

xv) Providing, fixing, jointing and testingin position ISI marked (IS:4985) UPVC pipes of min 6 Kg/ Sqcm ratingwith fitting for waste pipe from fixturesto floor trap including reduces,enlarger, socket, couplers, bends,tees etc including fixing at wall/ ceilinglevel supported by clamp & hangersetc. cutting holes in wall/ floors/ slabsand making good the same withcement concrete 1:2:4 complete asrequired.32 mm dia.

xvi) Providing, fixing, jointing and testingin position ISI marked (IS:4985)UPVC pipes of min 6 Kg/ Sqcm ratingwith fitting for waste pipe from fixturesto floor trap including reduces,enlarger, socket, couplers, bends,tees etc including fixing at wall/ ceilinglevel supported by clamp & hangersetc. cutting holes in wall/ floors/ slabsand making good the same withcement concrete 1:2:4 complete asrequired.40 mm dia.

xvii) Providing & fixing UPVC Floor trap ofself cleansing design with stainlesssteel grating complete in all respects.

xviii) Extra for providing & fixing 125 mmdia C.P. grating in place of C.I. gratingover floor traps.

xix) Providing & fixing of SS FloorCleanout, round or square with rubberseal and flat round cover with screwsand other required fitting complete asrequired.

Provision for water supply piping works of washroom complete with all necessary fittings and fixings and changing of sanitary items wherever necessary etc for toilet block. i) "Providing & fixing 15 mm nominalbore 45 cm long unplasticised PVCconnection pipe with brass unions. 45cm length 15 mm nominal bore

ii) Providing and fixing C.P brass bibcock of approved quality conformingto IS standards IS: 8931. 15 mmnominal bore

iii) Providing and fixing C.P brass longnose bib cock of approved qualityconforming to IS standards andweighing not less than 810 gms. 15mm nominal bore

iv) Providing & fixing 15 mm nominalbore C.P brass angle valve for basinmixer and geyser points of approvedquality conforming to IS 8931.

v) Constructing brick masonry chamber300 x 300 x 500 mm, inside withF.P.S. brick work in cement mortar 1:4 (1 cement : 4 coarse sand) for StopCock, with C. I. surface box 100 x 100x 75 mm (inside) with hinged coverfixed in cement concrete slab1:2:4mix (1cement : 2 coarse sand:4grade stone aggregate 20mm nominalsize); necessary excavation,foundation concrete 1:5:10 (1 cement:5 fine sand: 10 graded stoneaggregate 40mm nominal size) andinside plastering with cement mortar 1: 3 (1 cement : 3 coarse sand ) 12 mmthick finished with a floating coat ofneat cement complete as perstandard design.With common burntclay F.P.S.(non modular) bricks ofclass designation 7.5

vi) Providing & Fixing G.I. Unoun in G.I. pipe including cutting and threadingthe pipe & making long screws etc. complete. of different size nominal bores as per actual requirment

vii) Cutting holes up to 30 X 30 cm inwalls including making good thesame:With common burnt clay F.P.S.(non modular) bricks

viii) Providing, fixing chlorinated polyvinyl Chloride (CPVC) pipes CTS-SDR 11, class-1 CPVC Pipes (pressure rating 28 kg/cm2 at 23oC and 7 kg/cm2 at 82oC) confirming to IS : 15778-2007, ASTM D-2846, having thermalstability for hot and cold water supplyincluding all CPVC plain and brass threaded fittings including fixing the pipes with clamps at 1.00 m spacing. This includes jointing of pipes &fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in charge. of various sizes for internal work exposed on wall

Providing, fixing chlorinated polyvinylChloride (CPVC) pipes CTS-SDR 11,class-1 CPVC Pipes (pressure rating28 kg/cm2 at 23oC and 7 kg/cm2 at82oC) confirming to IS : 15778-2007,ASTM D-2846, having thermalstability for hot and cold water supplyincluding all CPVC plain and brassthreaded fittings including fixing thepipes with clamps at 1.00 m spacing.This includes jointing of pipes &fittings with one step CPVC solventcement and the cost of cutting chasesand making good the same includingtesting of joints complete as per direction of Engineer incharge.Concealed work includingcutting chase and making good the wall etc. of various sizes as per actualrequirement

Excavating trenches of required width for pipes, cable, etc including excavation for sockets and dressing of sides, ramming of bottoms, depth upto 1.50m including getting out the excavated soil & then returning the soil as required, in layers not exceeding 20 cm in depth including consolidating each deposited layer by ramming, watering, etc & disposing of surplus excavated soil as directed within a lead of 50m.All kinds of soil Pipes cables etc. exceeding 80 mm dia. But not exceeding 300mm dia for toilet block

Providing, laying and jointing glazed stone ware pipes grade class SP-1 with stiff mixture of cement mortar in the proportion of 1:1 (1cement :1 fine sand) including testing of joints etc complete. 150 mm diameter for toilet block

Providing and laying cement concrete 1 : 5 : 10 (1 cement : 5 coarse sand : 10 gradded stone aggregate 40 mm nominal size) around S.W. Pipes including bed concrete as per standard design. 150 mm diameter S.W.Pipe for toilet block.

Constructing brick masonry manhole in cement mortar 1 : 4 (1 cement : 4 coarse sand) with RCC top slab with 1 : 2 : 4 mix (1 cement : 2 coarse sand : 4 grade stone aggregate 20mm nominal size); foundation concrete 1:4:8 mix (1 cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size) inside plastering 12 mm thick with cement mortar 1:3 (1cement 3 coarse sand ) finished with a floating coat of neat cement and making channels in cement concrete 1:2:4 (1cement : 2 coarse sand: 4 graded stone aggregate 20 mm nominal size) finished with a floating coat of neat cement complete as per standard design."Inside size 90 x 80 cm & 45 cm deep including CI cover with frame (light duty) 455 x 610mm internal dimensions, total weight of cover & frame to be not less than 38 kg (weight of cover 23 kg and weight of frame 15 kg) With common burnt clay F.P.S.(non modular) bricks of classic designation 7.5 for toilet block

Constructing brick masonry manhole in cement mortar 1 : 4 (1 cement : 4 coarse sand) with RCC top slab with 1 : 2 : 4 mix (1 cement : 2 coarse sand : 4 grade stone aggregate 20mm nominal size); foundation concrete 1:4:8 mix (1 cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size) inside plastering 12 mm thick with cement mortar 1:3 (1cement 3 coarse sand ) finished with a floating coat of neat cement and making channels in cement concrete 1:2:4 (1cement : 2 coarse sand: 4 graded stone aggregate 20 mm nominal size) finished with a floating coat of neat cement complete as per standard design "Inside size 120 x 90 cm & 90 cm deep including CI cover with frame (Medium duty) 560mm internal diameter, total wt. of cover & frame to be not less than 208 kg (wt. of cover 108 kg and wt. of frame 100 kg) With common burnt clay F.P.S.(non modular) bricks of classic designation 7.5 for toilet block.

Extra for depth for manholes: size 90 X 80 cm With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 for toilet block

Extra for depth for manholes: size 120 X 90 cm With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 for toilet block.

Extra depth for circular type manhole 0.91m internal dia (at bottom) beyond 0.91 m to 1.67 m.With Sewer bricks conforming IS : 4885 for toilet block

Providing and fixing square mouth S. W. Gully trap class SP-1 complete with C.I. grating brick masonry chamber with water tight CI cover with frame of 300 x 300 mm size (inside) the weight of cover to be not less than 4.50 kg and frame to be not less than 2.70 kg as per standard design 180 x 150 mm. size P type With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 for toilet block.

Providing M.S. foot rests including fixing in manholes with 20x20x10 cm cement concrete blocks 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) as per standard design :With 20x20 mm square bar for toilet block

Provision for electrification works of toilet block complete with all necessary fittings & electrical items wherever necessary etc for toilet block. i) Wiring for light point/fan point/exhaustfan point/call bell point with 1.5Sq.Mm FRLS PVC insulated copperconductor single core cable in surface/ recessed medium class PVCconduit, with modular switch, modularplate,suitable GI box and earthing thepoint with 1.5 Sq.Mm FRLS PVCinsulated copper conductor singlecore cable etc. as required.Group C

ii) Twin Control Point wiring in PVCconduit, with modular type switch :-Wiring for twin control light point with1.5 Sq.Mm FR PVC insulated copperconductor single core cable insurface/recessed medium class PVCconduit, 2 way modular switch,modular plate,suitable GI box andearthing the point with 1.5 Sq.Mm FRPVC insulated copper conductorsingle core cable etc. as required.

iii) Power plug wiring in PVC conduit (2 x4 Sq.Mm.) :-Wiring for power plugwith 2 x 4 Sq.Mm. FRLS PVCinsulated, copper conductor singlecore cable in surface / recessedmedium class PVC conduit along with1 no 4 Sq.Mm FRLS PVC insulatedcopper conductor single core cable forloop earthing as required.

iv) Power plug wiring in PVC conduit (4 x4 Sq.Mm.) :-Wiring for light/powerplug with 4 x 4 Sq.Mm. FRLS PVCinsulated, copper conductor singlecore cable in surface / recessedmedium class PVC conduit along with2 nos. 4 Sq.Mm FRLS PVC insulatedcopper conductor single core cable forloop earthing as required.

v) Wiring for circuit / submain wiringalongwith earth wire with the followingsizes of PVC insulated, copperconductor single core cable insurface/ recessed medium class PVCconduit as required.2 X 2.5 sq. mm +1 X 2.5 sq. mm earth wire.

vi) Wiring for circuit / submain wiringalongwith earth wire with the followingsizes of PVC insulated, copperconductor single core cable insurface/ recessed medium class PVCconduit as required.4 x 10 sq.mm. + 2x 6 sq.mm. Earth wire

vii) S/F light plug point Modular typeaccessories :-Supply and fixing ofsuitable size GI box with modularplate and cover in FRLSont onsurface or in recess includingproviding and fixing 3 pin 5/6 ampsmodular socket outlet and 5/6 amps.modular switch, connection etc. Asrequired. (For light plugs to be used innon residential buildings).

viii) S/F power plug point modular typeaccessories Supply and fixing ofsuitable size GI box with modularplate and cover in FRLSont onsurface or in recess, includingproviding and fixing 6 pin 5/6 & 15/16amps modular socket outlet and 15/16amps. modular switch, connection etc.as required.

ix) S/F modular type electronic fanregulator :-Supply and fixing twomodule stepped type electronic fanregulator on the existing modularplate switch box including connectionsbut excluding modular plate etc. asrequired.

x) S/F modular type blanking plateSupply and fixing modular blankingplate on the existing modular plate &switch box excluding modular plate asrequired.

xi) Supplying and fixing 5 amps. to 32amps. rating, 240 volts `C' series,miniature circuit breaker (MCB)suitable for inductive load offollowing poles in the existing MCBDB complete with connections, testingand commissioning etc. Asrequired.single pole

xii) S/F TP MCB Isolator-"Supplying andfixing following rating, four pole, 415V, isolator in the existing MCB DBcomplete with connections, testingand commissioning etc. 40 Amps

xiii) Supplying and fixing following rating,four pole, (three phase & neutral) 415volts, residual current circuit breaker(RCCB), having a sensivity currentupto 300 miliamperes in the existing MCB DB complete with connections,testing and commissioning etc. Asrequired :40 amps.

xiv) Supplying and fixing following way,horizontal type TP&N, sheet steelMCB distribution board, 415 V onsurface /recess, complete with tinnedcopper bus bar, neutral bus bar, earthbar, din bar, interconnections, powderpainted including earthing etc. Asrequired (But without MCB / RCCB /Isolators). 4 way (4 + 12), Doubledoor

xv) Supply of Cirrus Mini Surfacemounted LED downligher 15 watt withDie-cast Housing & Heat Sink, 900Lumens at system level , LED Driveris compliant to IEC Standards.Dimensions: 312 X312X72mm,CRI>70, In luminaire the led chip,driver and heat sink should be ofsame make to ensure systemreliability.(Such as Philips SM518CLED9S 6500 PSU WH or Equivalent).

xvi) Supply of Astra Surface & wallmounted LED batten with extrudedaluminum housing and robustconstruction of 15 watt & 1300Lumens with all accessories as perstandard item..(Such as PhilipsBN150W LED13S-6500 PSE OD GRor Equivalent).

Supply of Cirrus Mini Surfacemounted LED downligher 24 watt withDie-cast Housing & Heat Sink, 1600Lumens at system level , LED Driveris compliant to IEC Standards.Dimensions: 312 X312X72mm,CRI>70, In luminaire the led chip,driver and heat sink should be ofsame make to ensure systemreliability.(Such as Philips SM518CLED16S 6500 PSU WH orEquivalent).

xviii) Supply of AC 230/250 volts, 50 HZceiling fan with standard down rod,blades, 2 nos. caps & regulator etc.ISI marked complete as required. 900mm sweep

xix) Supply of AC 230/250 volts, 50 HZexhaust fans including providing nuts,bolts, mounting FRLSame and otheraccessories etc. complete 300 mmsweep 900 rpm

xx) Installation, testing andcommissioning of pre-wired,flourescent fitting / compactfluorescent fitting of all types,complete with all accessories andtubes etc. directly on ceiling / wall,including connection with 1.5 sq. mm.FRLS PVC insulated, copperconductor, single core cable andearthing etc. as required.

xxi) Installation, testing andcommissioning of ceiling fan includingwiring the down rod of standard length(upto 30 cm.) with 1.5 sq. mm. FRLSPVC insulated, copper conductor,single core cable, including providingand fixing phenolic laminated sheetcover on the fan box etc. as required.

xxii) Installation of exhaust fan in theexisting opening, including makinggood the damage, connection, testing,commissioning etc. as required.Upto450 mm sweep

Construction of Septic tank & soak pit for 100 users. Note : Construction of Septic tank includes Surface dressing, Excavation, P.C.C., Brick Work, filling in soak pit, Internal Plaster of Septic tank, Form Work,Concrete Work, Steel Reinforcement, Plumbing work & Installation of ant type of fitting / pipe work from toilet block to septic tank & soak pit for functioning of the toilet block & septic tank. All the items are included for toilet block.

Provision for digging a borewell for water supply includes all necessary activities such as site preparation, drilling to the required depth, and installation of casing pipes, etc., as directed by engineer in charge for toilet block. i) Drilling of 600 mm. dia. through allkinds of formations using Rotary/DTHdrilling rig up to specified depth as perthe recommendation of thegeophysical surveys and water yield.The scope of work includes thesetting of drilling rig at specifiedlocation and shifting to another location and disposal of muck andbentonite slurry (if any) etc.

ii) Excavation of a pit for watercirculation 5mX3X3mtr

iii) Development of tube well with aircompressor till water gets free fromsand particles and silts.

iv) Supply, installation andCommissioning of PVC pipe.IS:12818 Class CM Size :: 12" (300mm) dia Plain pipe including socketsof standard design.

v) Supply, installation andCommissioning of PVC pipe.IS:12818 Class CM PVC pipe. Size :12" (300 mm) dia slotted pipeincluding sockets of standard design.

vi) Supply, installation andCommissioning all necessary tubewell fittings and Bail plug with hook, MS housing clamp, well cap, sanitarysealing of well at top etc. in allrespects.

vii) Supply, installation andCommissioning of Submersible pumpmotor set of approved make suitablefor tube well of 7.5 HP

viii) Panel board for submersible pumpfitted complete

Providing and laying design mix reinforced cement concrete with crushed graded stone aggregate 20mm nominal size using batching plant, transit mixer and concrete pump, in all works upto plinth level excluding cost of form work.1:1½:3 (1 cement: 1½ coarse sand (zoneiii) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources) for toilet block

Providing and laying 60mm thick faciory made cement concrete interlocking paver block of M -30 grade made by block making machine with strong vibratory compaction, of approved size, design & shape, laid in required colour and pattern over and including 50mm thick compacted bed of coarse sand, filling the joints with line sand etc. all complete as per the direction of Engineer-in-charge for parking area.

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundation and plinth in: Cement mortar 1:6 (1 cement : 6 coarse sand) for parking area.

Providing and laying at or near ground level factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5mm), including making drainage opening wherever required complete etc. as per direction of Engineer-in- charge (length of finished kerb edging shall be measured to calculate volume for payment). (Precast C.C. kerb stone shall be approved by Engineer-in charge) for parking area.

Centering and shuttering including strutting, propping etc. and removal of form for Foundations, footings, bases of columns, etc. for mass concrete for parking area.

Centering and shuttering including strutting, propping etc. and removal of form for Columns, Pillars, Piers, Abutments, Posts and Struts for parking area.

Provision for providing 12 mm cement plaster of mix : 1:4 (1 cement: 4 fine sand) for parking area.

Provision for Wall painting with acrylic emulsion paint, having of approved brand and manufacture, including applying additional coats wherever required, to achieve even shade and colour for boundary wall of parking area.

Stone work plain ashlar in domes , in super structure upto floor V level in cement mortar 1:3 (1 cement : 3 coarse sand) including centering, shuttering and pointing with white cement mortar 1:2 (1 white cement : 2 stone dust) with an admixture of pigment matching the stone shade. Both face dressed Red sand stone for entrance gate of the temple.

Providing and fixing stone jali 40 mm thick throughout in cement mortar 1:3 (1 cement : 3 coarse sand), including pointing in white cement mortar 1:2 (1 white cement : 2 stone dust) with an admixture of pigment, matching the stone shade, jali slab without any chamfers etc. Red sand stone for all the sides of the step-well (kund)

Construction of granular sub-base by providing close graded Material conforming to specifications, mixing in a mechanical mix plant at OMC, carriage of mixed material by tippers to work site, for all leads & lifts, spreading in uniform layers of specified thickness with motor grader on prepared surface and compacting with vibratory power roller to achieve the desired density, complete as per specifications and directions of Engineer-in- Charge.With material conforming to Grade-II (size range 53 mm to 0.075 mm ) having CBR Value 25 for pathway around the outer pond.

Construction of granular sub-base by providing close graded Material conforming to specifications, mixing in a mechanical mix plant at OMC, carriage of mixed material by tippers to work site, for all leads & lifts, spreading in uniform layers of specified thickness with motor grader on prepared surface and compacting with vibratory power roller to achieve the desired density, complete as per specifications and directions of Engineer-in- Charge.With material conforming to Grade-I (size range 75 mm to 0.075 mm) having CBR Value 30 for pathway around the outer pond

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level 1:2:4 (1 cement : 2 coarse sand (zone-III) derived from natural sources : 4 graded stone aggregate 20 mm nominal size derived from natural sources) for pathway around the outer pond.

Stone work in plain ashlar in super structure upto floor five level in cement mortar 1:6 (1 cement : 6 coarse sand) including pointing with cement mortar 1:2 (1 white cement : 2 stone dust) with an admixture of pigment matching the stone shade : One face dressed Red sand stone for pathway around the outer pond

Provision of architectural lighting and illumination for the monument, including supply, installation, testing, and commissioning of high-quality LED floodlights and spotlights with IP65 or higher rating in warm white (3000–3500K) and CRI>80, complete with appropriate mounting brackets, corrosion-resistant poles, outdoor electrical panels with surge protection, automatic lighting control systems with timers and remote operation, conduits and cabling with UV and weather protection, integration with existing electrical infrastructure including circuit breakers and earthing, ensuring uniform illumination and compliance with IS standards (IS 10322) and relevant BIS codes, including testing and commissioning for lux levels and power consumption as directed by engineer in charge etc.,

MAA SHARDA CONSTRUCTION (BID ID -3245730)