REPAIRS TO CHAJJA PROJECTION LEAKAGE SEEPAGE OF ROOF BATHROOM SUNKEN TREATMENT AND CERTAIN CONNECTED BR WORKS IN OTM ACCN OF INF SCHOOL UNDER AGE BRI AREA OF GE MIS MHOW

Amount

Demolition of brick work / stone boulders masonry built in cement mortar includinmg all quoins , arches, pillars etc but excluding ashlar facings, dressed stone work and precast concrete articles complete all as specified.

M&L for brick work with modular size burnt fly ash bricks, straight or curved on plan exc. 6 m mean radius built in cement mortar (1:6), complete all as specified

Taking down cement plaster of any description on brick or stone walls etc including racking out joints hacking for key scrubbing down with water etc complete all as specified.

M&L for rendering 15mm thick plaster in CM (1:6) on fair faces of brick work or concrete surfaces, finished even and smooth without using extra cement complete all as specified.

M&L for 2mm thick wall care putty for newly plastered surfaces and prepare to smooth finish all as specified and directed.

M&L for rendering 15mm thick plaster in CM (1:4) on fair faces of brick work or concrete surfaces, finished even and smooth without using extra cement mixed with Dr fixit pidiproof LW 200ml/50Kg of cement and finished even and smooth without using extra cement all as specified. NOTE : WPC shall be measured and paid separately under relevant item.

M&L for rendering 5mm thick in cement mortar 1:3 on ceiling concrete surface, mixed with Dr fixit pidiproof LW 200ml / 50Kg of cement and finished even and smooth without using extra cement all as specified . NOTE : WPC shall be measured and paid separately under relevant item.

Supply only liquid water proofing compound

M&L for preparation of newly plastered surfaces of wall, pillasters, cornices etc and applying two or more coats of 100% premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489-2004, Alkali and fungal resistance,dirt resistance exterior paint of required shade (Company Depot Tinted) 1.43 litre/10 sqm over and including priming coat of exterior primer applied @ 0.90 litre /10sqm over new surface including preparation of new surfaces.

M&L for preparation of newly plastered surfaces of wall and applying three coats of white wash on surfaces of walls complete all as specified.

All as per item No. 10 above but one coat of white wash on ceiling complete all as specified.

M&L for newly plastered wall surface and applying two coats of oil bound distemper over a coat of Chalk whiting /cement based wall primer all as specified.

M&L for newly plastered ceiling surface and applying two coats of oil bound distemper over a coat of Chalk whiting /cement based wall primer all as specified.

M&L for preparation of old decorated surfaces of wall including brooming, scraping down, smoke spot,moss,efflorescent salt,trading oil, glossy spots and stopping nails marks and applying one coat of first quality exterior weather proof water base emulsion paint all as specified and directed Make: Asian (Apex) /Berger( weather coat Antidust)/nerolac(Excel) /Dulex(Weather sheild).

M&L for preparation of wall surfaces and applying two coats of oil bound distemper over a coat of wall primer including filling holes and porus area by wall care putty complete all as specified.

M&L for preparation of old surfaces of wall and applying two coats of white wash complete all as specified.

M&L for preparation of old treated surfaces of ceiling and applying one coat of white wash complete all as specified .

M&L for preparation of old treated steel surfaces of any description exceeding 10cm in width or girth and applying one coat of synthectic enamelled paint complete all as specified.

M&L for preparation of old treated wood or wood based surface of any description exceeding 10cm in width or girth and applying one coat of synthectic enamel paint complete all as specified.

Dismantling floor or wall tiles including cement mortar bedding and rubbish off the premises complete all as specified.

M&L for glazed ceramic coloured tiles of size 450mm x 300 mm x 6 to 7mm thick in dado or skirting over and including backing coat 10mm thick in CM (1:4), jointed in neat grey cement slurry and pointed in colour cement to match with colour of tile all as specified.

M&L for non skid ceramic coloured tile 7 to 8 mm thick (Square / rectangular ) area of each tile exceeding 0.06 Sqm but not exeeding 0.11 Sqm over and including 15mm thick screed bed in CM (1:6) in floors etc set and jointed in neat cement slurry and pointed in coloured cement to match with colour of tile all as specified.

M&L for non skid ceramic coloured tile 7 to 8 mm thick (Square / rectangular ) area of each tile exceeding 0.11 Sqm but not exceeding 0.18 Sqm over and including 15mm thick screed bed in CM (1:4) in floors etc set and jointed in neat cement slurry and pointed in coloured cement to match with colour of tile all as specified.

All as per item No 23 but as in skirting over and including 10mm thick backing coat in CM (1:4 ) complete all as specified.

Demolition of stone slabs, paving stones and tiles of any description and thickness in floors, aprons, laid, bedded and pointed in any mortar complete all as specified.

M&L for Machine cut kota stone slab flooring 20-25mm thick over cement screed base laid and jointed with grey cement slurry mixed with pigment to match with shade of the slab including rubbing and polishing complete including screed bed 15mm thick in CM (1:6) complete all as specified .

All as per item no 26 above but in skirting over and including 10mm thick rendering in CM (1:4 ) complete all as specified.

M&L for grinding cutting and polishing to surfaces of existing kota stone floor/skirting/dado complete all as specified and directed.

M&L for chequered cement concrete tiles of size 40cm x 40cm x 25 to 30mm thick (glossy finish) with grey cement and pigment including 15mm thick screed bed in CM 1:6, set , jointed and pointed in neat cement slurry in floors complete all as specified.

M&L for machine pressed rubber moulded precast concrete interlocking paver block (glossy finish) any shape and size confirming to IS 15658-2006 of 60 mm thickness, M-35 Grade with grey cement and pigment laid over 50 mm thick stone dust cushioning laid dry to the profile complete all as specified. Note: Sand cushioning shall be measured & paid seperately under relevant item.

M&L for 50mm thick stone dust filling under floors including watering and consolidation all as specified .

Demolition of cement concrete (unreinforced) in ground floors and paving not exceeding 15cm thickness (below or above ground level) complete all as specified.

Demolition of cement concrete exceeding 15cm depth of any description and in any position not otherwise specifically provided ( above ground level) including removal of concrete debries from site to a distance not exceeding 500 m complete all as specified.

M&L for PCC (1:5:10) type E2 using 40mm graded stone aggregate as in foundations, filling and mass concrete, sunken floors complete all as specified.

M&L for 75 mm thick PCC 1:3:6 type C2 using 40mm graded stone aggregate as in plinth protection finished the surface of concrete topping even and fair (without using extra cement) including making joint at every 3 metre interval and at corner and filled with mixture of bitumen and sand and laid in alternate bays complete all as specified .

M&L for 100 mm thick PCC 1:2:4 type B2 using 40mm graded stone aggregate in floor finished even and fair complete all as specified.

M&L for plain cement concrete 1:2:4 type B1 using 20mm graded stone aggregate 40mm thick as in flooring, coping, finish the surface even and smooth with using extra cement complete all as specified.

M&L for provide water proofing treatment to sunken floor surfaces of RCC slab by the following specification including taking down and cleaning of old surface all as specified and directed. (a) Provide PCC (1:1.5:3) type A0 using 12.50 mm graded stone aggregate in slope of average thickness 50mm mixed with and including liquid water proofing compound PIDIPROOF LW 100+ manufactured by Dr Fixit or other equivalent as approved by GE. (b) M&L for rendeering 15 mm thickness in CM 1:3 mixed with water proofing compound on sides of (Vertical surface) Sunken/RCC slab/Parapat wall (c) Applying first coat of Dr Fixit fatsflex with a stiff nylon brush and leave 4 to 6 hours for dry (d) After 4 to 6 hours completion of first coat applying second coat of Dr Fixit fatsflex at the direction of 90 degree to the first coat and leave 4 to 6 hours for dry. (e) After 4 to 6 hours completion of second coat , applying third coat of Dr Fixit fatsflex at the direction of 90 degree to the second coat and leave 4 to 6 hours for dry. Note : WPC shall be measured & Paid separatly under relevant item,

M&L for provide PVC spout pipe of 25 mm bore 45 cm length in sunken floor including cutting holes in brick walls built in cement mortor and making good the dismantled portion in PCC (1:2:4), type B1 using 20mm graded stone aggregate and finished the disturbed portion of external surfaces as per existing finish complete all as directed and specified.

M&L for cutting holes in brick walls built in cement mortor exceeding one brick but not exceeding two brick at the starting point of down take soil / waste pipe at any floor, fill the joint of down take pipe & trap with thick mortor in CM 1:3 and making good the dismantled portion in PCC (1:2:4), type B1 with using 20mm graded stone aggregate and finished the disturbed portion of external surfaces as per existing finish complete all as directed and specified.

M&L for roughening surface of old concrete surfaces by picking sweeping, cleaning and washing down with water to remove dust etc including taking down tarfelt and brushing neat cement slurry @ 3 Kg/Sqm of cement mixed with liquid type water proofing compound on dry concrete surface including 20mm thick screed bed for in cement morter 1:3 mixed with liquid water proofing compound including prepare the surface fair and even all as specified Note:- water proofing compound shall be measured and paid separatly under relevant item

M&L for preparation of surfaces and applying bituminous primer (conforming to IS-3384-1965) @ 0.40 Kg/Sqm complete.

M&L for applying two coats of tack coat with Industrial bitumen of grade of 85/25 at the rate of 1.2 Kg per Sqm including cleaning surfaces complete all as specified. Note : 1st coat for bonding material below membrane and 2nd coat on top of membrane.

M&L for APP based polymeric membrane minimum weighing 3kg/sqm and minimum 3mm thick reinforced with polyster non woven fabric weight not less than 150 gms/sqm laid on primed surface by forced application complete all as specified and as per Manufacture's instruction.

M&L for applying two coats of aluminium paint on APP membrance including preparing the surface complete all as specified.

M&L for applying two coats of bitumen based aluminium paint @ 0.15 Kg/Sqm for each coat over APP membrane including preparation of surface complete all as specified and directed

S&F in repair vitreous china squatting Pan “Orissa” Pattern, of size 580mm x 440mm white with integral foot rests (excluding flushing cistern and flush pipe) including connection to trap, and to fushing pipe , antisyphonage pipe, etc including making good to floor etc complete all as specified.

S&F in repair vitreous china wash hand basin of size 550mm x 400mm (flat back or angle back type) including cutting for and pinning in ends of brackets or erecting stand exclusive of fixing of supply and waste pipe etc complete all as specified.

S&F in repairs vitreous china pedestal pattern wash down water closet pan white colour including 110mm PVC(SWR) 'P' Trap and joint run and lead front or back inlet,connection to drain (or out going pipe ) and to flushing pipe antisyphone pipe plastic water closet seat cover white closed pattern with flat bottom and cover complete as specified and directed.

S&F in repair Vitreous China uninal bowl, half stall coloured, with PTMT urinal spreader for fixing 15 mm dia pipe , union for discharge pipe, providing and fixing plugs, bedding urinals against wall in cement mortar (1:2), securing urinal to plugs with and including 60mm long steel screws, pointing around the urinal back in white cement complete all as specified and directed.

S&F in repairs Urinal spreader of PTMT any colour for fixing with 15 mm dia pipe. (Minimum weight 60gms)

S& F in repairs mild steel chromium plated health faucet with 1metre SS tube and hook complete all as specified.

S&F in repairs chromium plated jet for EWC with 1.00 metre SS pipe including necessary GI fitting as required like nipple etc all as specified.

S&F in repair fancy chromium plated two way bib cock of 15mm bore screwed for iron pipe or brass ferrule etc complete all as specified.

M&L for repairing low level flushing cistern (i.e) adjustment of syphon washer,adjustment of handle, float valve as required and making the cistern fuctionable complete all as specified.

S&F in repair CP brass fancy type 15mm bore bib taps, screwed down and screwed for iron pipe or for brass ferrule complete all as specified.

S&F in repair Bib tap standard PTMT of any colour 15mm bore high pressure screwed for iron pipe and fixed all as specified.

S&F in repair 15mm bore pillar taps, cast copper alloy with capstan heads, chromium plated,fancy type screwed down high pressure with or without lettered “HOT” or “COLD” with long screwed shanks and fly nuts complete all as specified.

S&F in repair 15mm bore, 450mm long, PVC connections with brass unions internally threaded both ends complete fixed to iron pipe at both ends complete all as specified.

S&F in repairs CP fancy type angle cock one way, brass chromium plated, fixed to iron pipe or for unions 15mm bore complete all as specified.

S&F in repair CP fancy type Stop Valve ( Concealed type),cast copper alloy, screwed both ends for iron pipe or for union of 15mm bore complete all as specified.

S&F in repairs brass spindle for concealed stop cock of 15/20mm bore all as specified.

S&F in repairs CP brass fancy type shower rose 15mm dia with 125mm long CP nipple of approved quality complete all as specified.

S&F in repairs soap dish chromium plated brass fixed with brass nuts

S&F in repairs toilet paper holder brass chromium plated

S&F in repair towel rail 600mm long 20mm dia brass chromium plated fixed with wooden plugs embedded in cement mortar (1:3) with MS screws etc complete all as specified

S&F in repair LDPE pipe 32mm bore fixed to wall/ceiling with bend / elbow complete all as specified.

S&F in repair stainless steel grating round type 150mm size (Minimum Weight 100 gm) complete all as specified.

S&F in repair PVC valveless, syphonic action type flushing cistern, 10 litre capacity low/high level white with inlet ball valve float and handle including brackets complete all as specified and directed.

S&F in repairs PVC flush pipe of 32mm dia pipe with two numbers of check nuts for connecting low level flushing cistern to EWC complete all as specified.

S&F in repairs brass chromium plated waste coupling 32mm bore for WHB complete all as specified.

S&F in repair of 25mm bore ball valve high pressure of PTMT with epoxy coated aluminium rod and high density plastic ball screwed for iron pipe complete all as specified.

S&F PVC waste pipe fixed to any type of coupling of length not exceeding 1.50m length complete all as specified.

S&F in repair rotational moulded polythylene 500 litres capacity water storage tank (double layered) (cylindrical/ vertical with closte top) hoisted and fixed in position all as specified in SSR Part-I including providing and fixing PTMT ball valve high pressure with polythene float and fly nut, 20mm bore complete

S&F in repair rotational moulded polythylene water storage tanks(double layered ), 1000 litres capacity, (Cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part-I including providing and fixing PTMT ball valve high pressure with polythene float and fly nut, 20mm bore complete all as specified and directed.

S&F in repair rotational moulded polythylene water storage tanks (double layered ) 2000 litres capacity, (Cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part-I including providing and fixing PTMT ball valve high pressure with polythene float and fly nut, 25mm bore complete all as specified and directed.

M&L for cleaning & removing all scale and dirt from tank and from mouth of circulating pipe of 1000 litres capacity complete all as specified.

M&L for cleaning & removing all scale and dirt from tank and from mouth of circulating pipe of 2000 litres capacity complete all as specified.

S&F in repair gun metal gate valve 25 mm dia with lever arm screwd both ends for iron pipes complete all as specified

S& F in repairs sheet glass shelf assembly, approved make, consisting of 5.5mm thick sheet glass shelf 12 cm wide with chromium plated bracket guard and railing 60cm long complete all as specified.

S&F PVC (SWR) floor trap 75mm dia of out let ,plain with grating including jointing with solvent cement complete all as specified.

S&F PVC (SWR) multi floor trap 75mm dia of out let ,plain with grating including jointing with solvent cement complete all as specified.

S&F in repair PVC body bathroom cabinet with mirror fancy type made out of 5.5mm thick mirror of size 550 x 450mm complete, Model No 555 of PRAYAG or other equivalent as approved complete all as specified.

S&F in repair plastic water closet seat cover white closed pattern with flat bottom and cover with mild steel/ chromium plated or aluminised hinging device complete all as specified.

S&F in repair 110mm bore of PVC (SWR) pipes single socketed in any length with rubber ring joints laid on wall / floor with clip complete all as specified.

S&F in repair 75mm bore of PVC (SWR) pipes single socketed in any length with rubber ring joints laid on wall / floor with clip complete all as specified.

S&F PVC (SWR) branch piece, single (Single Y) equal or unequal 110mm size

S&F PVC ( SWR) bends any radius bore of 110 mm.

S&F PVC ( SWR) bends any radius bore of 75 mm.

S&F in repairs 25mm dia Stainless steel curtain rod as approved by GE complete all as specified.

S&F in repairs 25mm dia stainless steel decorative brackets as approved by GE complete all specified.

Taking up or down steel tubing 15mm bore including connections, S & F GI tubing medium grade with all fittings & fixed to walls /ceiling or laid in floors complete all as specified.

Taking up or down steel tubing 25mm bore including connections, S & F GI tubing medium grade with all fittings & fixed to walls /ceiling or laid in floors complete all as specified.

Taking down door shutter with frame not exceeding 1.5 Sqm each without taking off shutter from the frame complete all as specified.

S&F factory made steel Window with side hung shutter including projecting hinges with steel handle, stay complete all as specified.

S&F factory made steel Window with side hung shutter including projecting hinges with steel handle, stay complete without glazing bar and guard bar dovetailed or welded complete all as specified.

S&F chimney bars window guard bars etc fixed independently in steel frame with L or T section supports for shelves etc. and similar articles confirming to Fe-290 Gde E-165 all as specified.

S&F steel ventilator fixed type with glazing bar complete all as specified.

S&F PVC door frame of size 50 mm x 47 mm made out of 5 mm prelam PVC sheet reinforced with MS Square tube in opening of suitable size complete all as specified.

S&F Factory made (Prelam on both sides) solid panel PVC door shutter 30 mm thick (Style) consisting of frame made out of MS tubes for top and bottom rails, MS frame shall covered with heat moulded prelam PVC 'C' channel having a PVC sheet strip of 20 mm width stuck inside with solvent cement for styles and prelam PVC sheets for top rail, lock rail and bottom rail in either side and as gap insert for top rail and bottom rail pannelling of prelam PVC sheet to be filled in the MS welded/sealed to the styles and rails with suitable PVC sheet beading and jointed together wiht solvent and fixing in the frame at site as per specification and drawing complete all as specified and directed.

Taking down chowkhats or frames with shutter without taking off shutter from the frame exceeding 1.5 Sqm but not exceeding 4 Sqm each.

Taking down shutters of any description area exceeding 1.00 Sqm but not exceeding 2.0 Sqm.

S&F 35mm thick second class hard wood glazed and skeleton shutters, open rebated and prepared to receive glass, gauze etc. (without sash bars), edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass, etc.; size of members of shutters as specified in SSR Part – I, Section – 8, clause 8.24(a) ; supplied and fitted to chowkats all as specified.

S&F 30mm thick second class hard wood glazed and skeleton shutter, open rebated and prepared to receive glass, gauze etc. (without sash bars), edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass, etc. size of members of shutters all as specified in SSR Part – I, Section – 8, clause 8.24(a) ; supplied and fitted to chowkats all as specified.

S&F second class hard wood shutter 35mm thick, plain framed panelled shutter factory made (two panel) with lock rail & panel of 9mm BWP commercial ply or 12mm veneered particle board with commercial veneering on both faces. The size of rail and style as per IS:1003 complete all as specified.

M&L for pressed steel door frame of size 105X60mm with one or more rebates including necessary fixing lugs,hinges,lock strike plate.etc completet all as specified.

M&L for pressed steel door frame of size 125X60mm with one or more rebates including necessary fixing lugs,hinges,lock strike plate.etc completet all as specified.

S&F 100mm long aluminium alloy with galvanised mild steel hinge pin,anodised and fixed type B-22.

S&F in repair 100mm long aluminium alloy with galvanised mild steel hinge pin,anodised and fixed type B-22.

S&F in repair 100mm long butt hinges medium weight cold rolled mild steel.

S&F 200 mm long Aluminium anodized barrel tower bolts of extruded section.

S&F in repair 200 mm long Aluminium anodized barrel tower bolts of extruded section.

S&F in repair 150 mm long Aluminium anodized barrel tower bolts of extruded section.

S&F 150 mm size aluminium anodized handle.

S&F in repair 150 mm size aluminium anodized handle

S&F in repair mild steel ordinary rat tail rod pattern spring 300mm size including roller & roller plate complete all as specified.

S&F in repairs aluminium floor door stopper double legged length 140mm with hard drawn steel spring fitted in floor complete all as specified.

S&F in repair Aluminum plate type II 200mm size hook and eyes.

S&F in repair 40mm wide up to 5mm thick rubber beading fixed to door shutter with nails.

M&L for preparation of new wooden surfaces of any description over 10cm in girth or width and applying two coats of synthetic enamel paint over a coat of primer complete all as specified

M&L for painting with two coats of synthetic enamel paint to steel surfaces of any description over 10cm in width or girth over a coat of red oxide primer including preparation of surface complete all as specified.

S&F second class hard wood plain solid straight, chowkhats and frames,wrought framed rebated on the solid,rounded or chemfered,put togather with glue pinned at joints all as specified.

M&L for 19mm thick prelaminated particle board, both sides with decorative choice lamination including necessary second class hard wood 6mm thick edging for cup board all as specified.

S&F continuos ( Piano) hinges mild steel, bright finish or electro galvanized 30mm width flap ( When open) all as specified.

M&L for welding in repairs not exceeding 2.5 cm in length to the thickness of metal to be welded 9mm but not exceeding 20mm complete all as specified.

S&F stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire stapples complete all as specified.

S&F in repair galvanised MS wire cloth 0.56mm nominal dia of wire and average width of aperture 1.18mm fixed with tinned tacks or galvanized wire staples including taking out old wire mesh from steel window and fixing old steel flats and nut complete all as specified.

Haking out old brocken glass pane of any size thickness, quality or any description) from wooden frames or stone,concrete or brick surrounds, glazed with putty or fixed with beads complete all as specified. NOTE FOR SL ITEM NO 130 to 132 : Glazing work shall be carried out to the building upto G + 3 story .

S&F figured glass 3mm thick pin head type and glazing with oil putty and securing with glazing pins not exceeding 0.50 Sqm in each pane complete all as specified.

S&F sheet glass 3.0 mm thick ordinary quality and glazing with oil putty, in squares n. exc 0.5 sqm in each pan complete all as specified. NOTE : Glazing work shall be carried out to the building upto G+3 stried.

Dismantling plain or corrugated steel sheeting of any gauge, thickness including nanital or similar pattern roof covering all as specified.

S&F Pre- painted galvalume aluminum zinc coating GI based corrugated (profile pattern) steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws all as specified complete.

S&F Pre- painted galvalume aluminum zinc coating GI based plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws all as specified complete.

Dismantling Asbestos cement (corrugated, semi corrugated etc) sheets in roofs covering all as specified.

M&L for 6mm thick asbestos cement corrugated or semi corrugated sheets in roofs, walls etc fixed with L-type or J-type or cranked hook bolts all as specified.

M&L for Asbestos cement serrated ridge for corrugated or semi corrugated sheet fixed with L-type or J-type or cranked hook bolts all as specified.

Dismantling of Wall and ceiling boards (fibre, pulp, insulation, etc.) or insulation boards/slabs/ blankets, any thickness, including cover fillet complete.

Providing and fixing false ceiling at all heights with integral densified calcium silicate reinforced with fibre and natural filler false ceilling tiles of size 595X595mm of approved texture, design and pattern pinhole 8mm thick semi perforated square edge tile having NRC( noise reduction coefficient ) of 0.50 (minimum) Light refluctance of 85% (minimum) Non combustable as per BS : 476(PART-4) fire performance as per BS : 476(PART 6&7) humidity resistence of 100% thermal conductivity <0.043W/m K as per ASTM 518:1991, intrue horizontal level suspended on interlocking metal powder coated T-grid of hot dipped galvanized iron section on proffile,stitched double webbed white with 1mm reveal proffile ( White/black) comprising of main-T runner of size 15X 32mm of lenght 3000mm, cross-T of size 15 X 32mm of lenght 1200mm and secondary intermediate cross-T of size 15 X32mm of lenght 600mm to form grid module of size 600X600mm,from ceiling using galvanized mild steel Iron 8mm outer daimeter M-6 dash fasteners, 6mm dia threaded hanger rod and L- shape level adjuster of size 85X25X2mm galvanized iron perimeter wall angle of size 19 X 19mm of lenght 3000mm to be fixed on periphery wall/Partition with the help of plastic rawl plugs at 450mm cetre and 40mm long dry wall SS screws. The work shall carried out as per specifications, drawing and as per direction of the Engineer-in-Charge.

Dismantling of timber boarding of any description,fixed in any position with nails all as specified.

M&L for 4mm thick non asbestos cement plain building boards, fixed to wooden frame work with screws including preparation of new surfaces and applying two coats of white wash in ceiling complete.

M/s Himgiri construction

NIDHI CONSTRUCTION