SPL REPAIR TO BLDG NO T-76 AND T-79, PROVN OF RETAINING WALL, TOILET BLOCK, VEH PARKING HARDSTANDING, JAFFRI WALL, PCV WALL PANELLING AND GARBAGE BIN AT RMS

Amount

Demolition of cement concrete in ground floors and pavings n exc 15 cm thickness below or above ground level

Demolition of reinforced cement concrete in ground floors and pavings n.exc 15 cm thick above or below ground level.

Demolition and breaking up drain pipes (salt glazed, stoneware, AC or reinforced concrete/PVC pipe) set in cement mortar 150 /110 mm dia fixed in position.

Demolition of brick work built in cement mortar incl all quions, arches pillars etc but excl ashalar facing

Demolition of reed, lathing single or double, including battens and plaster or chicken wire lathing complete all as specified and directed.

Dismantaling floor,hearth or wall tiling including cement mortar bedding (but not backing),removing serviceable tiles to store and rubbbish off the premises.

Dismantling structural steel work including doors gates but excluding framed trusses etc

Dismantling timber in framed, fillets, rails, posts, rafters,purlins, etc. under 40 sq. cm in section

Dismantling of plain or corrugated sheeting of any guage/thickness in roof covering/wall clading complete all as spfd and directed

Disamantling wall and ceiling boards (fibre, pulp, insulation, etc.) any thickness including cover fillets complete all as specified and directed.

Taking down shutters of any description n exc 1Sqm in each complete all as specifed and directed.

Taking down chowkhat or frames not exc 1.5 Sqm each (without taking off shutter from the frame) complete all as specifed and directed.

Taking down chowkhat or frames exc 1.5 Sqm but not exc 4 Sqm each (without taking off shutter from the frame) complete all as specifed and directed.

Taking down PVC/AC/Salt glazed ware pipes and fittings upto 75/100mm.

M&L surface excavation not exc 30 cm deep and averaging 15 cm deep and getting out soft/loose soil.

Excavating in trenches not exceeding 1.5 m wide and not exceeding 1.5 m in depth, for foundation etc or for shafts,wells, cesspits, manholes etc not exceeding 10 sqm on plan and not exceeding 1.5 m in depth and getting out in soft/loose soil complete all as specified and as directed.

Excavating over areas in soft/loose soil, n exc 1.5 m deep and getting out

Excavation over areas exc 1.5m deep & n.exc 3 m deep and getting out in soft/loose soil

Returning, filling in soft/loose soil, including spreading, levelling, watering and well ramming in layers not exc 25cm.

M&L removing exacavated soil n. exc. 50m and depositing where directed at a level n. exc. 1.5m above starting point complete all as specified and directed.

Removing excavated soil material exc. 250 m but n exc. 500 m and depositing where directed

M&L formwork to roughly finished surface of concrete to soffits of suspended slabs such as roof slabs,floor slabs ,landings and similar work complete all as specified and directed.

M & L for Use and waste of Formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping)

Formwork to faces of walls, retaining walls, abutments, parapets and staircase railings and similar work for flat and rough finished concrete surfaces.

M&L for form work to sides of plinth beam,lintel beams etc with rough finished surfaces of concrete flat complete all as specified and as directed.

Hard core of broken stone guage n. exc. 63mm deposited spread and levelled in layers n. exc. 15cm thick watered and rammed to true surface.

Material and labour for loose filling with broken bricks of guage 40 to 80mm in soakage pits ,soakage wells,etc

M& L Plain cement concrete (1:4:8 )Type D-2 using 40mm graded stone aggregate as in foundation filling and mass concrete all as specified.

M&L for 100mm thick cement concrete type D-2, 1:4:8 (using 40mm graded aggregate) in floor as in sub base complete all as specified and directed.

M&L for cement concrete 1:3:6, type C2 (40mm graded stone aggregate) as in foundation filling and mass concrete.

M&L precast cement concrete 1:3:6, type C1(20mm graded stone aggregate) as in Kerb stone/bond stone.

M&L for PCC (1:3:6), type C-1 (20mm graded stone agg) as in coping and the like including weathering slightly rounded or chamfered angles and throating etc complete all as directed.

M&L 75 mm thick cement concrete type C2 1:3:6 (40 mm graded aggregate) as in plinth protection/sub base using extra cement for finishing.

M&L for PCC 1:3:6 type C-2 (40mm grade stone aggregate) as in bed to 160 mm dia SGSW /PVC pipes including packing under and haunching against the sides of pipes after they are laid and tested.

M&L for PCC 1:3:6 type C-2(40mm grade stone aggregate) as in surface channels and drains etc complete all as specified and directed.

Extra for forming fair finished surfaces of drain or channels, inner girth 30 cms, using extra cement including forms, moulds mitred/ stopped ends etc., complete.

Add or deduct for additional 25mm inner girth over or under 30 cm all as specified

M&L providing precast cement concrete louvers and jalies, 30mm thick (measured solid), type B-0 (12.5mm graded stone agg) including moulding but excluding frame and set in CM (1:4) complete

M&L for 25 mm thick PCC (1:2:4) type-B-0 using 12.5mm grade aggregate as in damp proof course.etc,

M&L 40 mm thick cement concrete type B-1, 1:2:4 (40 mm graded aggregate) in floor

M&L 100mm thick Cement concrete 1:2:4 type B- 2, (40mm graded aggregate) as in floor finished

M&L for cement concrete type B-2, 1:2:4 (40mm graded stone aggregate) Cement concrete in surface channels and drains all as specified.

M & L for precast cement concrete1:2:4 type B-1 using 20 mm stone aggregate as in manhole cover slabs round square or rectangular in shape and set in CM 1:4.

M&L for PCC 1:2:4 type B-0 (using 12.5mm graded crushed stone aggregate) as in cills, copings, benching on chajjas, roof kerbs, bed blocks and the like including weathering, slightly rounded or chamfered angles and throating as directed with and including necessary form work complete all as specified and directed.

M&L Reinforcement Cement concrete Type B1 1:2:4 (20 mm graded aggregate ) in lintel beam over 1.5m span etc mass concrete complete all as specified and as directed.

M&L for RCC Nominal Mix Type B1 1:2:4 (using 20 mm graded stone aggregate)as in columns, pillars, piers, posts and struts.

M&L RCC nominal mix Type B1, 1:2:4 (using 20mm graded stone aggregate) as in slabs suported on wall.

Material and labour Reinforced cement concrete (Nominal Mix) in cement concrete 1:2:4 type B1 using 20mm graded stone aggregate as in cover slabs of drains, manholes, septic tanks, soakage wells etc. complete all as specified & as directed by Engineer-in-charge. Note: - Reinforcement shall be measured and paid for separately.

M&L for RCC Nominal Mix Type B1 1:2:4 (using 20 mm graded stone aggregate) as in foundation, including rafts, footings, foundation beams; plinth beams; bases for coloumns, etc basement slabs under reamed piles and mass concrete.

RCC (1:2:4) type B-1 using 20mm graded stone aggregate as in band coping bed plate, benching etc including slightly rounded of chamfered angle, throating, etc complete all as specified and as directed.

Material and labour for deformed steel TMT bars 10 mm dia and over, cut to length, bent to shape required, including cranking, bending spirally or hooping for columns, hooking ends and binding with mild steel wire (annealed) n.less than 0.9mm dia complete all as specified.

M&L reinforcement TMT bars 5mm dia and over upto and including 10mm dia in stirrups, spacers and binders, bent to shape required including cranking required and binding with and including mild steel wire(annealed) not less than 0.9mm dia or securing with clips quality confirming to Fe-410 Gde E-250 complete all as specified and directed.

M&L for non skid coloured ceramic tiles 7 to 8 mm thick area of each tile exceeding 0.11 sqm but not exc 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match including screed bed 15mm thick in CM 1:6 all as directed .

All as per ser No 53 but on vertical surfaces such as skirting , dado risers to steps over and including 10 mm thick bedding layer in CM 1:4 , set and jointed in neat cement slurry and pointed in white or coloured cement to match all as directed.

M&L for coloured Glazed ceramic tiles in vertical surfaces of size 300mm x 200mm, 7mm thick over and including 10 mm thick bedding layer in CM 1:4 , set and jointed in neat cement slurry and pointed in white or coloured cement to match all as directed.

M&L for glazed cramic coloured tiles in vertical surface 450x350x7 mm thick and jointed in neat cemment slurry and pointed in white or colour cement to match the exeisting surface over 10 mm thick screed bed (1:4).

M&L anti fungal chequered cement concrete tiles 250mmx250mmx20mm thick with 20mm thick screed bed or bedding layer of mortar for laying floor finishes in cement mortar 1:4 etc, set, jointed and pointed in neat cement slurry with grey cement and pigments.

M&L for Machine pressed precast conctete interlocking paver block any shape and size confirming to IS 15658-2006 of 60 mm thickness, M-35 Grade including 50mm thick sand cusioning complete all as specified and directed.

S & F Pre-painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50 mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall fixed with self tapping screws complete all as specified and directed.

S & F Pre-painted galvalume aluminum zinc coating GI based Plain steel sheet 0.50 mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall fixed with self tapping screws complete all as specified and directed.

M&L mild steel work post, truss, purlin etc confirming to Fe 410-w grade E 250 quality B

S & F Plates (plain or chequered) channels. Square cut or notched (ordinary and counter sunk) forming holes, without any attachment conforming Fe 410-W (gde E-250 Quality-A)

Supply & fixing Rolled Mild steel framed work as in doors/netting frame or Gates of angle or other section with gusset plates, rails braces, etc., complete, drilled for fixing of steel sheeting or other covering and hanging and fixing complete.

S&F Framed brackets of angles or tees with web and flanges cut to shape, drilled and countersunk for screw, including bending and welding angles, as necessary, gusset plates, riveting, etc.. n exc 10 kg each brackets, conforming to Fe.290.Gde-E-165 complete all as specified and directed.

S & F for bands, straps, supports or stays for rainwater, ventilating pipes, incl bolts, if reqd : hooks (say), heavy, for large gates, hook and pintle hinges : large hasps and staples; chains; hand made sliding bolts ; clamps; hold fasts; waal ties; hooks for hanging fans; plain angle cleats for securing purlins to wood trusses or rafters; knee piece inserts,; two way and three way straps, plate washers and similar small articles conforming to Fe-290 Gde E-165

S&F steel work in tubular trusses, post, purlins including special shaped washer etc. Complete using ERW or induction butt welded tubes conforming to IS 1161-1979 grade st-240 complete all as specified and directed by Engineer - in – Charge

S/F 2nd class hard wood scantling as in purlins rafters ,& framed work etc clean sawn complete all as specified and directed.

M&L II nd class hard wood plain fillets square or rectangular in section cleansawn sectional area exc 6 sqcm and nexc 13 sqcm secured in nails complete all as specified and directed

M&L for II nd class hard wood plain fillets squaree or rectangular in section clean sawn secured with nails sectional area exc 13 sqcm and n.exc 25 sqcm complete all as specified and directed

M&L for 2nd class hard wood plain solid straight chowkats and frames wrought framed rebated on the solid rounded or chamfered put together with glue pined joints complete all as specified and directed.

S & F for 35 mm thick flush shutters , solid core construction, with block board core and plywood face panels, commercial type on both sides complete all as specified and directed.

M/L 30mm thick 2nd class hard wood Glazed and skelton shutter, open rebated and prepared to receive glass, gauge etc. divided into squares with plain chamfered or rounded, mitred and rebated sash bars edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass etc. sizes of members of shutters as specified in SSR Part-I Section-8 clause 8.24(b) complete all as specified.

M/L 35mm thick 2nd class hard wood Glazed and skelton shutter, open rebated and prepared to receive glass, gauge etc. devided into squares with plain chamfered or rounded, mitred and rebated sash bars edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass etc. sizes of members of shutters as specified in SSR Part-I Section-8 clause 8.24(a) complete all as specified.

M&L for one coat of creasote oil to wooden surfaces new or old of any description including prepration of surfaces complete all as specified and directed

S&F soild PVC door frame of size 50mm X 47 mm made out of 5mm plain colour PVC sheet reinforced with MS square tube.

S&F factory made solid panal PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottem rails. M.S. frame shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheet strip of 20mm width stuck inside with solvent cemnt for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail ; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded/sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement.

S & F for 4 mm thick of size 600x600mm HSPC (high pressure Steam Cured) pre-Painted self embossed, textured designer board E-Board Classic to be fixed GI powder coated grid/section size 600mmx600mm with main runner 38x24x0.9mm thick ,cross tee 28.6x24x0.9 mm and wall angle 19x19x0.9 mm duly suspended with 4mm dia GI bar hangers 1200mm centre to centre both ways fixed with steel dash fasteners or from purlin from the roof with alignment clip including providing provisions for light fixtures of any size etc complete all as specified.

M&L 15 mm thick plastering in CM 1:4 on one side of lathing in two separate layers even and smooth without using extra cement complete all as specified and directed.

M&L 15 mm thick plastering in CM 1:6 the other side of lathing finished even and smooth without using extra cement complete all as specified and directed.

M&L for rendering 10mm thick plaster in CM 1:6 on fair faces of brick or concrete work finished the surface even and smooth without using extra cement.

M & L for 15mm thick cement plaster in cement mortar (1:4) on brick or concrete surface mixed with water proofing compound as per manufactures instructions, finishing the surface even and smooth without using extra cement complete all as specified.

Supply only integral water proofing compound (ISI marked)

Material and labour for brick work in cement mortar1:4 with sub class `B' bricks straight or curved on plan exceeding 6m mean radius with old size bricks.as in MH,pillars complete all as specified.

M&L half brick work with sub class "B" bricks straight or curved in plan exceeding 6 mtr mean radius built in CM(1:4).

Material and labour for brick work in cement mortar1:4 with sub class `B' bricks in one brick thick honey comb walling

M & L sheet glass ordinary quality 3mm thick and glazing with oil putty in squares n.exc. 0.5 sqm each pane complete all as specified and directed.

S&F galvanised mild steel wire cloth 0.56 mm nominal dia of wire and average width of aperture 1.18 mm and fixed with tinned tacks or galvanised wire staples all as directed by Engineer- in -Charge.

M&L GI wire netting 0.71 mm dia and 12 mm mesh lathing in to reed in walls incl all laps cutting and waste complete all as specified and directed.

S&F 100mm long stainless steel butt hing.

M&L butt hinges medium grade cold rolled mild steel and fixed size of hinges 100 mm long size

M&L butt hinges, medium weight 75 mm long size

S/F Aluminium anodised barrel tower bolt of extruded section and fixed 100 mm long

S/F Aluminium anodised barrel tower bolt of extruded section and fixed 200 mm long

S&F 150mm long aluminum hook and eye, complete all as specifed and directed.

S&F Aluminium handle cast type anodised 150 mm long

S&F 100mm size aluminium handles,cast type,anodised all as directed complete all as specified and directed.

S/F Aluminium alloy anodised sliding door bolt with hasp and staple (bolt type fixing clips of sheet cast or extruxded section(300 mm long)

S&F 300mm, mild steel ordinary rat tail rod pattern springs including roller and roller plate complete specified and directed

S&F floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed in floor, overall length of cover plate 140mm.

M&L for preparation of old painted surfaces of wood and wood based material of any description over 10 cm in width or girth and applying one coat of synthetic enamel paint all as specified.

M&L for preparation of new untreated wooden surfaces of any description not otherwise described over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer.

M & L for preparation of new steel surface and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and as directed

M&L for applying two coats of oil bound distemper on new plastered surfaces of walls including preparation of surface complete all as specified and directed.

M&L preparation of new surfaces & applying two coats cement base paint over a coat of primer complete all as specified and directed.

M&L for preparation of new plastered surfaces and applying three coats of white wash on walls all as specified & directed by Engineer-in-Charge

M & L for preparation of new surfaces of wall including scrapping down, smoke soot, efflorescent salts trading oil and greasy spots etc by applying two coat of white wash on walls

Taking up or down steel tubing and connections including cleaning for refixing with all fittings for 15 mm bore GI tubing.

S&F 15 mm dia GI tubes 'medium grade' with all fitting and fixed complte to walls or laid in floor

S&F 20 mm dia GI tubes 'medium grade' with all fitting and fixed complte to walls or laid in floor

M&L walling of random rubble, uncoursed, well bonded, bedded and solidly hearted, built in CM 1:6.

M&L raised pointing to random rubble or polygonal rubble, uncoursed or brought upto courses in CM 1:4.

5mm thick PVC sheet fillet of width 35mm for wall panelling inclusive of fixing on to wall to make PVC Frame as per specification and drawing

S & F 5mm thick PVC wall lining consisting of 5mm thick plain colour PVC sheet inclusive of solvent Cement and fixing at site on PVC frame all as specified and directed.

S&F in repair 75 mm PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to floor

S&f 110mm dia PVC (SWR) pipes single/double socketed in any length with rubber ring joints, laid in trenches or in floors and jointed as specified.

Suuply & fix 160mm dia PVC (SWR) pipes single/double socketed in any length with rubber ring joints, laid in trenches or in floors and jointed as specified.

S & F PVC (SWR) bends any radius 110 mm dia

S&F 75mm PVC(SWR) bends any radius with acess door.

S & F 75mm dia, PVC (SWR) floor trap, plain with grating including jointing with solvent cement complete all as specified and as directed.

S&F PVC (SWR) 110mm dia junction single T equal or un equalwith an floor

S&F PVC (SWR) 75mm dia vent cowl

S & F PVC valve less, syphonic action type, flushing cistern, low level, white, with inlet, ball valve, float and handle including brackets 10 ltrs capacity incl flush pipe complete all as specified.

S&F in repairs vitreous china water closet (squatt pan) orrisa pattern 580x440 mm size pan white with front or back inlet with integral 'foot rests including provn of lime concrete bedding including connections to 'flushing cistern/pipe complete all as specified and directed including 100mm CI 'P' trap.

S&F in repairs vitreous china water closet Padestal pattern (white) excluding fixing bolts, flushing cistern and flush pipe and including EWC Seat cover complete all as directed.

Supply and fixing vitreous China wash down water closet pan (pedestal pattern) with ‘P’ or ‘S’ trap, front or back inlet, fixing bolts, with coloured PVC seat cover and making all necessary connections complete as specified and as directed by the Engineer-in-Charge. Make: Parryware Cat No C0278 for water closet, Cat No C8071 EWC Standard for PVC seat cover or equivalent approved make.

S&F vitreous China Urinal, Half stall type, white (excluding flushing cistern, flush pipe) complete all as specified and directed.

S&F in repairs CP Health Faucet with 1 mtr metalic Expandable tube & hook complete all as specified and directed.

Supply and fixed in repair vitreous china wash hand basin including brackets, white size 550 x 400 mm incl cutting cutting for and pinning in ends of brackets. Including waste coupling,Waste fittings, brass, chromium plated for glazed ware sinks, basins, etc. with long screwed shanks and fly-nuts, flange end bedded in red lead cement and other and fixed

S&F in repairs for 15mm dia of pipe bib taps cast copper alloy, fancy type, chromium plated with crutch or butterfly handle screwed down, screwed for iron pipe or for brass ferrule and fixed.

S&F 15 mm dia bib taps, cast copper alloy with crutch or butterfly handle, screw down, screwed for iron pipe.

S& F in repairs Pillar taps, cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered ‘Hot' or ‘Cold' with long screwed shanks and fly-nuts, screwed for iron pipe and fixed complete all as spfd & directed.

S&F 15 mm dia stop valves fancy type CP screwed down high pressure with crutch or buter fly handle screw down, screwed for iron pipe.

S&F in repairs for 15mm dia of pipe stop valves,cocealed fancy type and chromium plated screwed down high pressure with crutch or butterfly handle screwed both ends for iron pipes or for Unions and fixed .

M & L for angular stop cock CP, fancy type 15 mm bore dia.

S&F 20 mm dia gate valves gun metal screwed down high pressure with iron wheel handle screwed both end for iron pipe or for unions.

S&F in repairs PVC connection 15mm dia and 45cm long with two Nos of brass checknuts and washers complete.

S&F in repairs 600mm long tubular tower rail brass chromium plated 20mm dia, D type 60cm longfixedwith two plugs (Gutties) of 2nd class hard woodembeded in cement mortor 1:3 with MS screwscomplete all as specified.

S& F in repairs PVC mounted 5mm thick bevelled edge looking mirror 550 x 400mm including taking down old fixed

S&F soap dish, CP approximate size 160x 160mm with chromium plated brass screws complete all as specified and directed.

M&L Concrete bed to 160 mm drain pipes including packing under and haunching against the sides of pipes after they are laid in trenches.

Cutting into existing manholes for 100mm bore pipe for connecting new drains, making good to pipe and rendering, cutting out existing benching for and forming branch channel (1/2 round or 3/4 section) in cement concrete 1:2:4 type B-1 smooth finished, and reforming benching as requried.

M & L Cutting into existing manhole/soakwell/septic tank making good to pipe and benching cutting out existing benching for and forming branch channel (half round or ¾ section) in cement concrete 1:2:4 type B-1 smooth finished and reforming benching as required for internal dia size 150mm.

Taking down carefully copper/ aluminium point wiring (light, fan, socket or power) complete, including fitting & fixtures such as switches with board, ceiling roses, pendents, bell/ buzzer, bell push, lamp holders, regulators, sockets, light fittings etc., removing material from site and making good to the disturbed surfaces of walls, ceiling, floors etc. including making good the disturbed surfaces and paint touch up to match with the existing surface complete all as specified and as directed.

M&L for Point wiring complete with two runs of 1.5 sqmm single core PVC insulated FR-LSH cable 1100 volts grade with multi-stranded copper conductors, drawn through and including PVC double locked Casing & caping including provision of 1.5 sqmm, FR-LSH, PVC insulated copper cable as earth continuity conductor connected to common earth dolly, including PVC rectagular box for mounting switches / sockets / regulators etc. with 3 mm thick plastic laminated sheet cover of suitable size as required at site and 50 mm deep complete all as specified and as directed.Make:- Richa/Finolex/Havells/RR Kabel Make of caping/casing & PVC boxes :- Prestoplast/Finolex/supreme/Richa

One light/Exhaust Fan point controlled by one, one way switch .

One light point/fan point controlled one way each addition light point on the same switch circuit

One 3 pin socket outlet 5 Amps on the same board with other switches.

One 3 pin socket outlet 5 Amps on the Independent board.

All as per item No-145 here-in-before but with 2.5 Sq mm for 3 pin 15 Amps socket point controlled by one switch on independent board and 2.5 Sq mm copper conductor green in colour as earth continuity conductor connected to common earth dolly complete all as specified and as directed.

M&L for Switch piano flush type single pole, one way 5A Make:- Anchor/SSK/Plaza

M&L for Socket outlet, 2 in 1, 3 pin 5A flush type Make:- Anchor/SSK/Plaza

M&L Switch socket combination 2 in 1, 5A/16A, 5 in 1 flush type Make:- Anchor/SSK/Plaza

M&L for stepped type electronic fan regulator 100 W socket size flush type on the existing phenolic laminated sheet etc. Make:- Anchor/SSK/Plaza

M&L for ceiling rose 3 terminal PVC/Polycarbonate isolated body complete all as specified and directed. Make:- Anchor/SSK/Plaza

M&L for 20W LED, 4', Wall mounted LED batten, extruded aluminium heat sink provided for efficient heat dissipation & integrated electronic driver.etc with all accessories internally pre-wired and fixing the same on and including two Nos PVC blocks and connecting up with flexible copper cable of size 0.75 Sq mm 3 core from ceiling rose to the light fitting incl taking down old unsv light fitting complete all as specified and as directed. Make : Havells Cat No LHFXCEP1TNNW020(batten) & LHDLEFXD5LR020(LED Tube) or equivalent in Bajaj/Philips

M&L for Lamp holder , PVC/ Polycarbonate type with PVC round/square block incl 9 watt LED lamp suitable for lamp holder fittings incl taking down old unsv light fitting. Make:- Anchor/SSK/Plaza MakeOf Lamp :- Havells/Bajaj/Philips

M&L for LED 1x20W Security light fitting, drawn through including GI bracket of 25mm bore light grade bent to shape and fixed on wall with metal fastners 2 Nos 10mm dia incl drilling holes as required and connecting up with flexible copper cable of suitable size from ceiling rose to the light fitting complete all as specified and directed. Make:-Havells Cat Pt No LHETBXU7PA6S020 or equivalent in Bajaj/Philips

Taking down Exh/Ceiling fan of any sweep carefully from its installed position, dismantling complete, cleaning all dust, applying grease for bearing, painting of fans complete with superior quality synthetic enamel paint by spraying including filling cavaties with filler, after cleaning all dust, reassembling the fan and blades, hanging/ fixing the fan in its original position and testing on completion complete all as specified and as directed.

M&L for rubber bush with clamping set, comprising GI bolt, nut and split pin complete all as specified and as directed.

M&L for replacemnt of capacitor 2.5 Mfd incl making electrical connection complete all as specified and as directed.

M&L for replacemnt of steel ball bearing/bush of suitable size compatible to the existing ceiling fan/Exhaust Fan complete all as specified and as directed.

M&L for copper rewinding for suitable size complete to the existing ceiling fan/Exhaust fan complete all as specified and as directed.

M&L for MCB Distribution board double door type TPN 4 way, sheet steel, powder painted, with copper bus bar neutral link & earth bar etc. and fixing MCBs of various rating capacity complete all as specified and as directed.Make : Legrand/ABB/Siemens

M&L for MCB Distribution board double door type SPN 4 way, sheet steel, powder painted, with bus bar neutral link & earth bar etc. and fixing MCBs of various rating capacity including taking down old unsv MCB DBs complete all as specified and as directed.Make:- Legrand Cat No 607711 or equivalent in ABB/Siemens

M&L for MCB TPN 100 Amps, 415 volts, 50 Hz suitable for fixing in MCB DB 'C' series complete all as specified and as directed.Make : Legrand/ABB/Siemens

M&L for MCB SPN 32 Amps, 230 volts, 50 Hz suitable for fixing in MCB DB 'C' series incl taking down old unsv MCB complete all as specified and as directed.Make:- Legrand Cat No 408636 or equivalent in ABB/Siemens

M&L for MCB SP 5-40 Amps, 230 volts, 50 Hz suitable for fixing in MCB DB 'C' series incl taking down old unsv MCB complete all as specified and as directed.Make:- Legrand Cat No 408587-95 or equivalent in ABB/Siemens

Taking down LT UG cable/ service connection of any size and M&L for laying of LT UG cable, XLPE insulated, galvanised steel strip or wire armoured, heavy duty electric cable with aluminium conductor, 1100 volts grade, cross-sectional area of 25 sq mm, 3.5 core complete all as specified and as directed. NOTE :- (i) Excavation and earth work, sand cushioning, cable protection cover, pipe etc. shall be measured and paid seperately under relevant items.Make : Richa/Finolex/Havells/Polycab

All as per Item No 165.00 10 Sqmm 2 Core -ditto- Complete all as specified and as directed.Make : Richa/Finolex/Havells/Polycab

All as per Item No 165.00 06 Sqmm 2 Core -ditto- Complete all as specified and as directed.Make : Richa/Finolex/Havells/Polycab

M&L for sub main wiring with two runs of 4 Sq mm and one run of 4 Sq mm for earth wire with multi standard copper conductors, 1100 volts grade, drawn through and including PVC double locked Casing & caping including complete all as specified and as directed. NOTE:- two runs of 4 Sq mm + one run of 4Sq mm and one run of PVC casing & capping and its accessories of suitable size shall be measured as one unit length .Make:- Richa/Finolex/Polycab Make of caping/casing :- Prestoplast/Finolex/supreme

M & L for Exhaust fan of 230 mm sweep sturdy metal body with metal louvers, comes with bird guard and double ball bearing all as specified and directed.Make : Bajaj/Havells/CGake: CG/Havells/Bajaj.

M&L for spread fine river sand in trenches complete all as specified ans as directed. NOTE: For measurement purpose, punned down thickness shall only be taken.

M&L for laying brick sub class 'B' old size burnt bricks for cable protection of size 230mmx115mmx75mm complete all as specified and as directed

Supply & laying tubes ' light grade' galvanised, with all fittings, fixed complete to walls, poles, ceilings for protection of cables of size 40 mm dia bore including taking out unsv GI tubing complete all as specified and as directed. Make:- Jindal/TATA/Prakash surya

M&L for earthing complete with galvanized steel earth plate electrode of size 600x600x6mm thick buried directly in ground (earth pit not less than 2.25m deep below the normal ground level) with top edge of the earth plate not less than 1.5 mtr below normal ground level connected to galvanised earth lead wire 4 mm dia as earth lead connectd by means of bolts, nuts, washers and check nuts all as shown in electrical plate No 3 of MES SSR Part-I, including testing on completion complete all as specified and as directed. NOTE:- (i) The unit rate shall also included for earth work in hard/ dense soil, PCC (1:3:6) type C1 chamber, CI frame with CI cover funnel with GI watering pipe 20mm dia Medium grade, GI protection pipe light grade 15mm dia and wire mesh complete in addition to item No 1 (a) to (e) of preamble (notes) under sub heading earthing, specified on Sl Page No 389 of MES SSR Part-II. (ii) Earthing lead and GI protection pipe beyond 7.5m will be measured and paid separately. (iii) Test points shall be made of GI strip 32x6 mm bridge type mounted on insulators, where ever applicable

M&L brick work with sub class B bricks straight or curved on plan exc 6 m mean radius in CM 1:6.

Excavating in post holes (or similar holes) each not exc 0.50 cum, getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers n.exc 25cm, watering, and removing surplus soil to a distance n.exc 50 m and making good surface in soft/ loose soil.

Dismantling timber scantlings unframed work 40 sqcm and over in section in any position complete all as specified and directed.

S& F in repairs Pillar taps, cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered ‘Hot' or ‘Cold' with long screwed shanks and fly-nuts, screwed for iron pipe and fixed complete all as spfd & directed.

M&L rendering 15 mm thick in CM(1:6) on fair faces of brick work or concrete surfaces of wall of any description, and finishing the surfaces even and smooth without using extra cement complete all as specified and directed.

M & L for 15mm thick cement plaster in cement mortar (1:4) on brick or concrete surface mixed with water proofing compound as per manufactures instructions, finishing the surface even and smooth without using extra cement complete all as specified.

Shri Atoshe Tuccu

VIHUTO YEPTHO

M/S MUNGA LAL PRASAD

Rameshwar Prasad

M/S VIKASH TRADERS

SHRI VIKASHE ZHIMOMI

M/S RAHUL TRADING CO.