SPECIAL REPAIR TO BLDG NO P-04 (FAMILY WARD OF MH) AND BLDG NO P-51(Ors MD ACCN IN OLD GOTHIC LINE) UNDER ZONE-II AREA AT JAIPUR MIL STN

Amount

Taking down cement plaster or cement lime plaster on PCC/stone surface/ brick surfaces/ceiling etc. including raking out joints hacking for key scrubbing down with water etc complete all as specified and directed.

Demolition of stone slabs and tiles of any description or thickness laid bedded and pointed in any mortar in floors, aprons etc. complete all as specified and directed.

Demolition of PCC in roofs, floors (other than ground floors ), beams, staircases, landing, chajjas and similar suspended work including removing out of MD land

M&L for rendering 15 mm thick in CM (1:4) on stone masonry surfaces finished even and smooth without using extra cement complete all as specified and directed.

M&L for rendering 10mm thick in CM (1:3) including finished even & smooth without using extra cement on ceiling/RCC facias complete all as specified and directed.

M&L for rendering 15 mm thick in CM (1:6) on brick/stone masonry surfaces finished even and smooth without using extra cement complete all as specified and directed.

M&L for preparation of new plastered wall surfaces and applying two coat of oil emulsion distemper of any tint including priming plastered surfaces with 3mm thick wall care putty in two layers complete all as specified and directed.

M&L for removal of existing treatment of plastered wall surfaces and applying two coat of oil emulsion distemper of any tint including priming plastered surfaces with 3mm thick wall care putty in two layers complete all as specified and directed.

M&L preparation of new plastered surfaces of ceiling and applying two coats of oil bound distemper surfaces with 3mm thick wall care putty in two layers complete all as specified and directed.

M&L preparing old decorative surfaces of wall and applying two coats of oil bound distemper oil emulsion of any tint complete all as specified and directed.

M&L preparing new plastered surfaces and applying three coats of white wash on ceiling complete all as specified and directed.

M&L preparing old plastered surfaces and applying two coats of white wash on ceiling complete all as specified and directed.

M&L preparing old plastered surfaces and applying two coats of cement base paint wall surface with 3mm thick wall care putty in two layers complete all as specified and directed.

M&L preparing of newly plastered surfaces of wall and and applying two coats of cement base paint surface with 3mm thick wall care putty in two layers complete all as specified and directed.

M&L for complete removal of existing treatment on wall surfaces and applying two coat of cement base paint over a coat of primer & wall care birla putty complete all as specified and directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiling to store and rubbish off the premises complete all as specified and directed.

M&L joint free Non Skid ceramic tiles(coloured) 7 to 8mm thick (squares/rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm, in floors etc. set over 15mm thick screed bed in CM 1:6 and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified and directed.

M&L Non Skid joint free ceramic tiles (coloured) 7 to 8mm thick (squares/rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc. set over 15mm thick screed in CM 1:6 and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified and directed.

M&L glazed ceramic coloured tiles ( 450 x 300 mm) x 7 mm thick, on vertical surfaces such as skirting, dados and risers to steps ,wall etc set over 10 mm thick cement plaster in CM 1:4 and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified and directed.

M&L glazed ceramic coloured tiles ( 400mm x 100 mm) x 7 mm thick, on vertical surfaces such as skirting, dados and risers to steps ,wall etc set over 10 mm thick cement plaster in CM 1:4 and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified and directed.

M & L for joint free Glazed ceramic coloured tiles of size (300mm x 450 mm) x 7 mm thick, on vertical surfaces such as skirting,/ dados and risers to steps ,wall etc set over and including 10 mm thick cement plaster in CM 1:6 and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified and directed.

M&L for Vetrified Ceramic tiles 10mm thick (square/rectangular) polished, area of each tiles not exceeding 0.36 sqm, in floors etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match. Light shade over and including 15 mm thick screed bed in CM 1:6 etc. complete all as specified and directed.

M&L 30mm thick, PCC 1:2:4 using 20mm graded stone aggregate as in floor finished fair & even complete all as specified & as directed.

M&L machine cut Kota stone slab flooring 20-25 mm thick over 15 mm thick cement screed base laid in CM 1:6 and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified & as directed.

M&L Kota Stone Slab 20-25 mm thick in riser of steps , skirting , dado and pillar laid over 15 mm thick cement plaster in CM 1:4 and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified & as directed.

M&L 18-20 mm thick Granite stone (table rubbed & polished) in steps, shelves, jambs & window cills/kitchen platform including bedded & jointed with grey cement slurry & pointing in white cement using marble dust with admixture of pigment to match with marble shade of Granite stone & including grinding & polishing the exposed edges complete all as specified & as directed.

M&L rounding to edges of stone slabs (Kota / Granite) one edges such as in steps, cooking platform and other similar situations complete all as specified & as directed.

Taking up or down steel tubing and connections, bore of pipe in 15mm. NOTE:- Unserviceable pipe shall be come property of contractor vide Schedule of credit.

S&F GI tubing medium grade with all fitting 15 mm bore fixed to wall or concealed or fitted to ceiling or laid under floor

Refixing old steel tubing including cleaning and connections in new or old position (walls, ceiling, floors, etc.) bore dia pipe in 15 mm.

Taking up or down steel tubing and connections,bore of pipe in 20mm. NOTE:- Unserviceable pipe shall be come property of contractor vide Schedule of credit.

S&F GI tubing medium grade with all fitting 20 mm bore fixed to wall or concealed or fitted to ceiling or laid under floor .

S&F in repairs stop valves cast copper alloy, screwed down high pressure with crutch or butterfly handle fancy type, chromium plated with long shank concealed type, screwed both ends for iron pipe or for unions in 15 mm bore.

S&F stop valves cast copper alloy, screwed down high pressure with crutch or butterfly handle fancy type, chromium plated with long shank concealed type, screwed both ends for iron pipe or for unions in 15 mm bore.

S & F in repairs stop valves cast copper alloy screwed down high pressure with crutch or butter fly handle, screwed both ends for iron pipe or for unions in 20 mm bore.

S&F in repairs to bib taps/fancy type chromium plated 15mm dia cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule over and including extension piece and CP cap.

S&F in repair PVC connections 15mm size with PTMT nuts of length 450mm

S&F in repair brass chromium plated towel rail 20mm dia D type 60cm long between flanges of brass chromium plated.

M&L Shelf of PTMT fixed with and including Chromium plated brass screws and wooden / plastic cleats (minimum weight 300gms)

S/F in repair chromium plated shower roses with or without swivel joints, any size, including fixing to steel pipe or union ,of size 125mm size complete all as specified & as directed.

S/F in repair Ball brass valves, high pressure, with polythene float and flynut complete, screwed for iron pipe or brass ferrule 20mm etc. complete all as specified & as directed.

S/F capacity 500 Litres rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part I including dismantling of old water tanks complete all as specified & directed.

M&L ball valves 20mm dia high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball screwed for iron pipe and fixed. (Minimum weight 20mm-210gms).

S/F stainless steel plate rack 600x600x225mm of approved quality made of 1 mm thick sheet complete all as specified & as directed.

S&F in repairs sink with drainage board made of stainless steel 1mm thick for kitchen with plugs, washers and wastes, including fixing cantilever brackets and connecting union to pipe overall size 915mm X 460mm bowl size 410mm X 330mm X 160mm complete all as specified & as directed.

S&F in repairs vitreous china squatting pan, `Orrisa' pattern, size 580 x440 mm white, with integral foot rests (excluding flushing cistern and flush pipe) complete all as specified & directed.

M&L cleaning sunken portion of slab (Bottom & sides) and providing water proofing treatment as under :- (a) Providing min 3" concave coving with PCC 1:2:4 type B-0 using 12.5mm graded stone aggregate admixed with WPC complast X 421 IC. Cement slurry admixed with bonding compound Nitobond AR to be used for bonding of coving with RCC member. Covering CI pipes with PCC 1:2:4 type B-0 using 20mm graded stone aggregate admixed with integral WPC complast X 421 IC (Fosroc Chemicals India Ltd). (b) Drilling 50mm deep holes at a distance of 1m c/c and cleaned with water and air, fixing nozzles of 12mm dia on drilled holes, injecting non shrink cement slurry at a pressure of 40 psi and nipples plugged with quick setting compounds. (c) Applying 2 full coats of brush bond acrylic emulsion based elastromeric water proofing coating after the primer with a min time gap of 4-6 hrs between 1st & 2nd coat. (d) Applying 15mm thick plaster in CM 1:4 admixed with WPC complast X 421 IC.

M/L Cement concrete filling and mass concrete in suken portion type F-2 1:7:12 ( 40 mm graded aggregates )

Supply only Integral water proofing compound.

S&F band straps supports or stays for rainwater, ventilating pipes including bolts if required, clamps, hold fasts and similar articles confirming to Fe 290 Gde E-165.

S/F in repair Vitreous China wash basin, white, flat back, size 550x400mm but including brackets, coupling and waste pipe complete all as specified & directed.

S&F PVC waste pipe 25 mm dia 75 mm long with 32 mm dia connecter for WHB.

S/F in repair Pillar taps, cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered `Hot' or `Cold' with long screwed shanks and fly-nuts, screwed for iron pipe 15mm

M&L cast iron floor trap 75mm dia with grating including jointing to waste pipe fixed in cement concrete type B1(1:2:4) complete all as specified & directed.

Taking down Shutters of any description exceeding 1 sqm and not exceeding 2.00 each.

Taking down chowkats or frames with shutters not exceeding 1.50 Sqm each (without taking off shutters from the frames).

Taking down shutters exceeding 1.5 sqm but not exceeding 4.00 sqm each (without taking off shutters from the frames).

Framed work as in doors or gates of angle or other section as chowkhat, tie bar, hold fast, guard bars complete, drilled for fixing complete conforming to Fe 290 Gde-E-165.

S&F in repairs framed work such as grills, gratings etc, with ends of bars shouldered and/or riveted or forged into spikes, framed guard bars, barred iron doors, ladders, framed guard bars, barred iron doors, ladders, framed balusters, walk ways, railings, frame work of water tanks and similair work confirming to Fe 290 Gde E-165.

Steel window with side hung shutters Factory made including box type hinges with steel handle and steel peg stay complete with glazing bars dovetailed or welded including taking down old. (Note: Mild steel wire cloth shall be measured and paid separately under respective items)

Steel window with side hung shutters Factory made including box type hinges with steel handle and steel peg stay complete without glazing bars dovetailed or welded including taking down old. (Note: Mild steel wire cloth shall be measured and paid separately under respective items) etc. complete all as specified & directed.

S&F factory made steel ventilator with top hung shutter including hinges, steel peg stay and handle complete all as specified & directed.

Steel windows or ventilators, fixed type, with glazing bars, complete all as specified & directed. complete all as specified & directed. Note: Wire gauge shall be measured and paid separately.

Factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails, M.S. frame shall be covered with heat moulded plain colour PVC `C' channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S frame wedded/ sealed to the stiles, & rails with suitable PVC sheet beading, and joined together with solvent cement, supplying & fixing in the frame at site as per specification & drawing complete all as specified & directed.

M&L 35mm thick factory made plain, framed, panelled door shutters kiln seasoned and chemically pressure treated second class, hardwood (two panels) with lock rail and panel of 9mm thick BWP commercial marine grade ply wood bonded with high quality liquid phenol formaldehyde synthetic resin adhesive confirming to IS-710. The size of rails and style shall be as per IS-1003. The shutter shall be fitted to chowkhats complete all as specified & directed.

S&F 35mm thick factory made second class hardwood glazed and skelton door shutter kiln seasoned and chemically treated, open rebated and prepared to receive glass/ gauge etc (without sash bars), edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass, etc complete. The size of members of shutters shall be as specified in MES SSR Part-I. The shutter shall be fitted to chowkhats complete all as specified & directed.

S&F Pressed steel factory made cupboard shutter with frame of 1.25mm thick and shutter 1mm thick PBI sheet with 6 Nos 3.15mm thick and 100mm long steel hinges Godrej pattern locking arrangement including 12mm dia vertical rod. Shutters shall be spray painted in factory including taking down of existing (total width including frame shall be measured and paid).

Aluminium anodised barrel tower bolts of extruded section and fixed of size 150 mm.

Aluminium anodised barrel tower bolts of extruded section and fixed of size 150 mm fixed in repair.

S&F in repair aluminium alloy anodised sliding door bolt with hasp & staple (bolt type) and fixing clip of sheet, cast or extruded section, bolt not less than 16 mm dia, 300 mm long (ISI marked).

S&F aluminium alloy anodised sliding door bolt with hasp & staple (bolt type) and fixing clip of sheet, cast or extruded section, bolt not less than 16 mm dia, 300 mm long (ISI marked).

S & F butt hinges of size 100mm medium weight cold rolled mild steel and fixed complete all as specified and directed.

S&F 100 mm double action spring hinges mild steel with steel wire spring stove enamelled black.

S&F aluminium handles extruded fabricated type anodized of size 125mm.

S&F in repair aluminium handles extruded fabricated type anodized of size 125mm.

S&F Harrison rails, of anodised aluminium alloy with fixing brackets, etc.

S&F fancy type brackets for drapery rod.

Stain less steel wire cloth, 0.36 mm nominal dia of wire and average width of aperture 1.40 mm and fixed with stainless steel wire staples.

Stain less steel wire cloth, 0.36 mm nominal dia of wire and average width of aperture 1.40 mm and fixed with stainless steel wire staples fixed in repairs.

Preparing new wooden surfaces of any description exceeding 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer.

Preparing old wooden surfaces of any description exceeding 10 cm width or girth and applying two coats of synthetic enamel paint .

Preparing old wooden surfaces of any description exceeding 10 cm width or girth and applying one coat of synthetic enamel paint .

Preparing new steel surfaces of any description exceeding 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide zink chrome.

Preparing old steel surfaces of any description exceeding 10 cm width or girth and applying two coats of synthetic enamel paint .

M&L plain cement concrete type C-1 1:3:6 (using 20mm graded stone aggregates) as in plinth protections 100 mm thick finished even and fair.

M&L for repairing to RCC chajja of doors/windows with PCC (1:2:4) type B1 or cement mortar 1:3 as directed by Engineer in charge

M&L PCC 1:2:4 type B1(using 20 mm graded stone aggregate) over chajja, coving at junction of chajja and wall finished even and smooth in any situation and position including form work complete

Cast iron soil sand cast, waste and vent pipes, in any length with or without ears with cement joints, laid in trenches or in floors of size 100 mm bore.

Cast iron soil sand cast, waste and vent pipes, in any length with or without ears with cement joints, laid in trenches or in floors of size 75 mm bore.

Cast iron soil sand cast, waste and vent pipes, in any length with or without ears with cement joints, on walls of size 100 mm dia.

Cast iron soil sand cast, waste and vent pipes, in any length with or without ears with cement joints, on walls of size 75mm dia.

S&F cast iron Bends 100mm bore, with oval access doors

S&F cast iron Bends 75mm bore, with oval access doors

S&F in cast iron Tee 100 mm bore, single

S&F cast iron Tee 75mm bore, single

S&F cast iron cowls 100 mm

Brickwork with subclass `B' bricks, straight or curved on plan exceeding 6m mean radius, built in CM (1:4).etc. complete all as specified and directed.

Demolition of brickwork or stone/boulder masonry, built in lime mortar including all quions, arches, pillars etc, but excluding ashlar facings, dressed stonework and precast concrete articles.etc complete all as specified and directed.

M&L PVC syphonic action type flushing cistern 10 litres capacity, low level white with inlet ball valve float and handle including brackets. etc. complete all as specified and directed.

M&L applied a coat of bituminous primer confirming to [email protected] Kg per Sqm ,APP BASED POLYMERIC Membrane not less than 3 mm thick. Weighing not less than 3 Kg/m2, reinforced with polyester non woven fabric(weighing not less than 15 Gm/Sqm) shall be laid dry torch application, side overlaps shall be 75 mm and end slab shall be 100 mm and all over laps and joints shall also be sealed by torch application all as directed ,one coat of bituminous aluminium paint and screed bed or bedding layer or mortar 15mm thick in cement mortar 1:4 with WPC on roof surfaces including taking down cement plaster on roof surfaces, cleaning and removing rubbish including roof treatment etc. complete all as specified and directed. Note:- WPC shall be measured and paid seperately under relevant item.

M&L 25 mm thick cement concrete type B-0 (using 12.5mm size graded stone aggregates) average as in RCC roof surface to horizontal and vertical surfaces , finish the surfaces even and smooth using extra cement including necessary form work all as specified and directed.

M&L cutting out cracks to V-section in existing roofs or terracing, cleaning out and filling solidly with a hot mixture of bitumen and clean dry sand 1:1 (by weight).

Supply only liquid water proofing compound.

Extra over rendering or plastering for work in isolated widths or in widths not forming part of general plastering such as in bands, sunk panels, cornices, skirting’s, drip moulds and similar work exceeding 15cm but not exceeding 30cm in width or girth; including cutting to edges, all mitres and stopped ends, etc.

S&F gun metal globe or gate valves with iron wheel head screwed both ends for iron pipe and fixed for 15mm dia pipe (ISI Marked)

S&F gun metal globe or gate valves with iron wheel head screwed both ends for iron pipe and fixed for 20mm dia pipe (ISI Marked)

S&F in repair brass chromium plated soap dish, complete all as specified.

S&F brass chromium plated magic eye.

S&F floor door stopper overall length of cover plate 140 mm of aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed in floor complete all as specified and directed.

S&F in repair floor door stopper overall length of cover plate 140 mm of aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed in floor complete all as specified and directed.

Cutting chases pinning in making good to facings if required & pointing in CM 1:3 to ends or edges or edges of landings steps, cills, sunshades shelves and cutting chases for concealed water tubing etc exceeding 10cm but not exceeding 20cm girth.

S&F in repair salt glazed stone ware gully traps in repairs square or rounded mouthed type P or S of size 150 x 150cm incl excavation earth work conc in Beds, surrounds kerbs etc complete.

S&F Cupboards knobs 40 mm dia of brass polished

Cutting holes 25 mm dia in kota stone for gas pipe

M&L in repairs for 18/19mm thick prelaminated particle board medium density flat pressed single layer or three layer type, BWP, exterior grade, fixed with screws to timber frame work, complete all as specified.

S&F block boards grade I quality exterior grade commercial type fixed with screws to timber framework 19 to 20mm thick with 6 mm thick teak wood leaping alround.

S&F 19/20mm thick exterior grade prelaminated particle board (Prelaminated on one side) as in CB shutter, pelmet including 6mm thick teak wood lipping and necessary rebating for double shutter where required including polishing to lipping complete all as specified.

Dismantling Boarding any description fixed in any position with nails.

S&F 150 mm hasp and staple safety type of aluminium anodized with mild steel hinges pin including bolt to hinge and fixed with screws .

S&F continuous piano hinges mild steel bright finish or electro galvanised width of flap 30mm,

Dismantling timber in fillets, rails posts rafter purlin etc under 40 sqcm in section in framed work.

M&L fillets square, rectangular or triangular in section but bull nosed, splayed chamfered or rounded on one edge wrought exceeding 3 sqcm but not exceeding 6 sqcm in section of 2nd class hard wood fixed with nails.

M&L fillets square, rectangular or triangular in section but bull nosed, splayed chamfered or rounded on one edge wrought not exceeding 3 sqcm in section of 2nd class hard wood fixed with nails.

M&L plain fillets square rectangular in triangular in section of 2nd class hard wood exceeding 13 Sqcm but not exceeding 25 Sq cm in section, wrought fixed with nails all as specified.

M&L for doors/window shutters re-securing or easy closing/opening tightening of hinges or changing the position of hinges adjustment of tower bolt sliding board etc exceeding 1 Sqm and not exceeding 2 Sqm each.

GI Wire netting 0.90 mm dia and 12 mm mesh lathing to wood or metal studding, joists etc in wall ceiling stanchion etc. complete all as per specified and directed.

S&F ball magnetic ball catcher

S&F 50 mm dia PVC(SWR) pipe

S&F 50 mm dia PVC(SWR)bend

S&F 50 mm dia PVC(SWR) tee

M&L 75mm thick cement concrete in foundations, filling and mass concrete type D2, (1:4:8) using 40 mm graded aggregate.

M&L for machine pressed precast concrete interlocking paver block, 60mm thickness, M-35 grade of any shape and size confirming to IS-15658-2006, with grey cement and no pigment laid over and including 25mm thick coarse sand laid over sub base as specified and directed.

M&L Pre-cast cement concrete block masonry (1:2:4) type B-1 using 20mm graded stone aggregate with solid blocks, exceeding 10 cm in width and setting in cement mortar (1:4) complete all as per specified and directed.

Demolition of cement concrete in ground floors and pavings not exceeding 15cm thickness (below or above ground level), including removing out of MD Land.

S& F suspended false ceiling with extra micro perforation size of 600 x 600 x 15 mm Ceiling Tiles over suspension metal system (MICRO LOOK) designer grid (15 mm grid 8mm return) SILHOUETTE X L 15 MM (NOMINAL) etc. complete including necessary hanging system arrangement which is required to be made from existing RCC roof / stone slab of building including dismantling of existing ceiling all as directed by Engineer-in-Charge. Make:- Ceiling tile - ORCAL of Armstrong or equivalent. Grid - Armstrong or equivalent.

Taking down existing aluminium door of any size and refixing in same opening after easing and changing necessary jointing cleats, glazing clips, rubber packing anodised aluminium snap beading and screw complete all as per specified and directed.

S&F in repairs wall mixer valve 15mm dia Make: Cat part No QQT-CHR-7219 of Jaquar or equivalent of Parryware/Marc.

S&F in repairs central hole single lever wash basin mixer 15mm dia with 450mm braided connection pipe of Make: Jaquar or equivalent of Parryware/Marc.

S&F in repairs 15mm bore bib tap two way, cast copper alloy chromium plated, fancy type with capstan head, screwed down, screwed for iron pipe or for brass ferrule. Make:Cat part No QQT-CHR-7041 of Jaquar or equivalent of Parryware/Marc.

S&F in repair of CP pressure JET for EWC with one metre pipe complete all as specified and directed.

S&F fancy type Health faucet 15 mm bore (ISI marked) including extension Pipe of one metre Long Make: New Cat Part No F8030301 of CERA or equivalent Parryware/ Hindware.

S&F in repairs Vitreous China snow white wash basin, Cyress pattern size 670 mm x 480 mm with half pedestal , 32 mm dia CP waste coupling & 25 mm dia, 75 cm long PVC waste pipe with 32 mm dia connector Make: New Cat Part No S2040130 Wash Basin S2090114 Half Pedestal of CERA or equivalent Parryware/ Hindware.

S&F soap tray chromium plated complete all as specified & as directed. Make:New Cat Part No F5006106 of CERA or equivalent Parryware/ Hindware/Jaquar.

S&F of brass CP Magazine holder complete all as specified and directed.

S&F CP brass Towel ring Make: New Cat Part No F5001105 of CERA or equivalent Parryware/ Hindware/Jaquar.

S&F toilet paper holder Make: New Cat Part No F5001109 of CERA or equivalent Parryware/ Hindware/Jaquar.

S&F corner glass shelf large 300mm x 300mm Make: New Cat Part No F5005103 of CERA or equivalent Parryware/ Hindware/Jaquar.

S&F in repairs PVC low level flushing cistern 10 Ltrs capacity with inlet ball vlave float and handle including brackets 15mm dia PVC connection and flushing pipes all as specified and directed by Engr-In- charge.

S&F in repairs CP bib taps, cast copper alloy with capastan heads ,screwed down, screwed for iron pipe or for brass ferrule and fixed of 15 mm bore.

S&F in repairs gun metal globe or gate valves with iron wheel head screwed both ends for iron pipe and fixed for 20mm dia pipe (ISI Marked).

S&F in repair tubular towel rail 20 mm dia ,D type,60 cm long between flanges with brass chromium pated bracket complete all as specified and directed.

S&F in repairs Vitreous China squatting pan, `pedestal pattern (EWC) white in colour with and including plastic seat cover white closed pattern with flat bottom and cover and MS chromium plated hinging device including connection to outgoing pipe complete all as specified and directed by Engr - In - charge . , size 580 x440 mm white, with integral foot rests (excluding flushing cistern ), complete all as specified and directed.

Taking down eaves gutters and rain water pipes (any size or pattern ) including fittings heads, shoes bends swan neck etc complete all as specified and directed.

S&F in repair PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors of 75 mm bore complete all as specified and directed.

S&F in repair PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors of 110 mm bore complete all as specified and directed.

S&F in repair PVC (SWR) bends of any radius 110mm bore complete all as specified and directed.

S&F in repair PVC (SWR) bends of any radius 75mm bore complete all as specified and directed.

S&F PVC (SWR) junction single (single T) equal or unequal 75mm bore complete all as specified and directed.

S&F PVC (SWR) junction single (single T) equal or unequal 110mm bore complete all as specified and directed.

S&F in repair PVC (SWR) pipes single socketed, in any length with rubber ring joints, fixed to wall of 110 mm bore complete all as specified and directed.

S&F in repair PVC (SWR) pipes single socketed, in any length with rubber ring joints, fixed to wall of 75 mm bore complete all as specified and directed.

S&F in repair PVC (SWR) Bends 100/110mm bore, with oval access doors complete all as specified and directed.

S&F in repair PVC (SWR) Bends 75 mm bore, with oval access doors complete all as specified and directed.

S&F PVC (SWR) vent cowl 110mm bore complete all as specified and directed.

S&F PVC (SWR) vent cowl 75mm bore complete all as specified and directed.

M&L in repair PVC (SWR) floor trap 75mm with grating including jointing with solvent cement complete all as specified and directed.

S&F Stack clamps, out of 50mm by 5mm flat iron and 16mm dia round iron stays, including bolts and nuts and securing ends of stays to wall or roof in 100/110 bore of pipe.

S&F Stack clamps, out of 50mm by 5mm flat iron and 16mm dia round iron stays, including bolts and nuts and securing ends of stays to wall or roof in 75 bore of pipe.

S&F in repairs PVC Grating doom 125 mm dia with waste hole of PTMT (Min Weight 40 gms) fixed complete all as specified and directed.

M&L brick work with old size bricks with fly ash bricks straight or curved on plan exc 6.00 metre mean radius, built in cement mortar 1:6 complete all as specified & directed.

Trellis work (jafri ) including taking as under of batten in trellies ( post and rail measured seperately )one way complete all as specified & directed.

Providing precast cement concrete louvers and jallies, type B0 1:2:4 using 12.5mm graded aggregate set in cement mortar 1:4 including Pillars for finishing at regular interval and taking down old one of 30mm thick (measured solid), including all mouldings but excluding frame. Note:- Pre cast frame shall be measured and paid separately.

S&F Solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S Square tube, in opening as per specification & drawing.

S&F aluminium handles cast type anodized of size 150mm.

S&F in repairs aluminium powder coated doors/window/ventilators and partition frame with shutters of approved section including necessary jointing cleats , glazing clips , rubber framing anodised aluminium snap beading screw etc complete all as specified and directed.

S&F powder coated aluminium work for, grills of 6mm dia rod square, rectangular , circular or similar type of shape fixed with channel etc. complete all as specified and directed.

M&L double action floor spring hydraulically regulated made up of minimum 1.25 mm thick aluminium alloy sheet foundation box, main body with stainless steel cover, governing pivot made of brass, other parts made of mild steel heavy duty and fixed.

M&L sheet glass, ordinary quality and glazing with oil putty in square not exceeding 0.5sq.m in each pane. thickness in 5.5mm.

Mortice lock, vertical type, size 100 mm and fixed Brass four levers.

S & f in repairs aluminium (die cast) hydraulic regulated , designation No 3, universal type door closer suitable for door shutter of 851 to 1000mm in width and weight between 61 to 84 Kg.

Taking down carefully surface aluminum or copper point wiring with PVC casing capping or conduit (light, fan, socket, bell or power) including fixture and fittings such as switches, ceiling rose, regulators, sockets, light fittings etc and making good disturbed surfaces complete all as specified & directed.

M&L for point wiring with 1100 volts grade PVC insulated FRLS multistranded copper conductor cable 1.5 Sq mm (Phase - Red, Neutral - Black) and earth continuity conductor 1.5 Sq mm (Green) drawn into and including concealed rigid non-metallic PVC conduit medium grade not less than 20 mm dia ISI marked ivory colour with all conduit fittings / fixing accessories and unwelded sunken galvanized pressed steel terminal boxes of thickness not less than 1.0 mm covered with 3 mm thick phenolic laminated white sheet cover for mounting switches, sockets, fan regulators as required for the following :- (Note - Cost of cutting of chases in stone/brick masonry and making good disturbed surfaces for concealing the conduit shall deemed to be included in quoted rate of point wiring).

(a) One light point controlled by one switch.

(b) One fan point controlled by one switch.

(c) one light point controlled by two, two way switch.

(d) One socket outlet 6 amp controlled by one switch on the same board with other switches.

(e) One socket outlet 6 amp controlled by one switch on independent board.

(f) One bell point controlled by one bell push.

M&L for point wiring with 1100 volts grade PVC insulated FRLS multistranded copper conductor cable 2.5 Sq mm (Phase - Red, Neutral - Black) and earth continuity conductor 2.5 Sq mm (Green) drawn into and including concealed rigid non-metallic PVC conduit medium grade not less than 20 mm dia ISI marked ivory colour with all conduit fittings / fixing accessories and sunken galvanized pressed steel terminal box of thickness not less than 1.0 mm covered with 3 mm thick phenolic laminated white sheet cover for mounting switches, sockets as required for one 16 amp socket outlet point controlled by one switch on independent board. (Note - Cost of cutting of chases in stone/brick masonry and making good disturbed surfaces for concealing the conduit shall be deemed included in quoted rate of point wiring).

S&F angle holder, insulated polycarbonate body with back plate complete.

S&F switch piano flush button single pole one way 6 Amp complete.

S&F switch piano flush button single pole one way 16 Amp complete.

S&F of switch flush type, 6Amp, SP, two way complete

S&F of bell push, flush type, 6Amp 240 Volts complete

S&F of door bell, AC, 240 Volts, SP complete

S&F socket outlet 2 in 1, 3 pin 6 & 16 amp flush type complete.

S&F socket outlet 2 in 1, 2 & 3 pin, 6 amp, flush type complete.

S&F ceiling rose 6 amp, 3 plates polycarbonate body complete.

S&F hum free electronic step fan regulator 120 - 280 volts of 100 watt capacity (socket type) including connecting up complete.

M&L for sub main wiring along with earth continuity conductor with, PVC insulated FRLS multistranded copper conductor cable (Phase-Red, Neutral-Black, Earth-Green) drawing into and including concealed rigid non metallic PVC conduit, medium grade, ISI marked ivory colour along with accessories as required for the following :-

(a) 2x6.0 Sq.mm + 1x6.0 Sq.mm earth wire in 25mm dia conduit.

(b) 2x4 Sq.mm + 1x4 Sq.mm earth in 20mm dia conduit.

(c)2x10Sq.mm + 1x10 Sq.mm earth in 25mm dia conduit.

M&L brick work with sub-class “B” bricks , straight or curved on plan to any radius in half brick thick walls, built in cement mortar 1:4 and plastering 10mm thick in cement mortar 1:4 including two coats of white/colour washing to match the existing surface complete all as specified & directed.

S&F sheet metal enclosure with a two pin and earth plug and socket complete with MCB single pole and 20 Amps

S&F MCB distribution board, powder coated, CRCA steel sheet, degree of protection IP 43, IK-09 with reversible double door, recess mounted , having insulated 100 Amps tinned copper bus bar, neutral bus bar, earth bar, din bar, detachable gland plate, interconnection, earthing connection, blanking plates in unused spaces as required for the following :-

(a) SPN, 240 volts, 8 ways.

(b) TPN, 415 volts, 4 ways.

S&F MCBs of 'C' series having breaking capacity 10KA, ISI marked including required wiring connections with copper lugs of suitable size provided in MCB DBs as required for the following :-

(a) Single pole 6 to 32 Amps

(b) Double pole 10 to 32 Amps.

(c) Four pole 40 to 63 Amps.

M&L for chemical earthing with GI pipe electrode 3.0 m long having outer pipe dia 50 mm & inner pipe dia 25 mm duly filled with highly conductive and anti corrosive compound tested from NABL certified Laboratory of required quantity in ground by digging a bore of 100 mm dia surrounded by soil friendly backfill compound including connection with galvanised earth wire 4 mm dia from earth electrode to the equipment to be earthed duly protected in 15 mm medium grade GI pipe upto 7.5 m , making PCC pit of size 0.3 m x 0.3 m x 0.3 m (inner size) in mix 1:3:6 type C1 with PCC 1:2:4 type B-1, 40 mm thick cover with lifting hook made out of 8 mm dia bar an testing on completion to achieve value not more than 2.0 ohm etc. complete all as specified and directed.

S&F in repair LED batten (1.2M) made of CRCA sheet housing with a PC glossy diffuser duly prewired connection having a nominal system lumen output of 2000 lumens at a minimum system efficacy of 105 lumen per watt and total power consumption not more than 19 watt including driver. It has a rated system life time of 40000 burning hours at L70 and should have a color temperature of 6500K, CRI>80, THD<10% and PF>0.95 complete. Make: Philips Cat Ref No. Endura Next Batten "BN 108C LED 20S PSU CDL WH" or equivalent in C&S/Surya//Havells.

S&F in repairs LED batten 9 watt, 900 lumens operating voltage 160 to 360 volts, colour temperature 6500K including connection all as per Philips Astra Line 9 Watt LED Batten or equivalent C&S/Surya//Havells..

S&F LED bulk head fitting 9 watt IP 66 & IK 09 with pressure die cast aluminium housing & polycarbonate diffuser duly pre wired connection with 0.75 Sq.mm PVC insulated & sheathed three core flexible multi stranded copper conductor cable. Make:- Philips Cat Ref No. WT 202W LED 6S PSU S2 PC or equivalent in C&S/Surya//Havells. as approved.

S&F LED bulb 12 watt Make:- Philips or equivalent in C&S/Surya//Havells.as approved.

Taking down industrial plug and socket including one number single pole MCB any make any capacity after disconnecting complete.

Taking down MCB distribution boards with incoming and outgoing controls any make any capacity after disconnecting complete.

Taking down carefully sub main wiring with PVC casing capping/PVC surface conduit and making good disturbed surfaces complete.

M&L for earthing with galvanized steel earth plate electrode 600mmx 600mmx6mm thick buried directly in ground (earth pit not less than 2.25 meter deep below normal ground level) with the top edge of the plate not less than 1.5m below normal ground level connected to galvanized earth lead wire 4mm dia by means of steel bolts, nuts, check nuts and washers all as shown in electrical plate No. 03 of SSR Part -I connected to earthing point and including 15mm bore light grade G.I. protection pipe (up to 7.5 meter from edge of the pit), PCC pit in mix 1:3:6 type C1 with PCC 1:2:4 type B-1, 40mm thick cover, watering arrangement with funnel and wire mesh and 20mm bore light grade G.I. watering pipe, common salt and charcoal filling, necessary excavation and earth work including testing on completion.

S&F steel tubes 40 mm bore light grade ISI marked with medium grade fittings for cable protection as required complete all as specified & directed.

Supply, laying and testing cable XLPE Insulated, screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 35 sq mm 3.5 core including taking down complete all as specified & directed.

Excavation in soft / loose soil in trenches not exceeding 1.5 m wide and not exceeding 1.5 m in depth and getting out complete all as specified & directed.

Returning filling with earth obtained from excavation including spreading watering and consolidation in layers not exceeding 25 cms thick complete all as specified & directed.

Removal of excavated material not exceeding 50m and depsiting where directed at a level n. exc 1.5 mtr above the starting point complete all as specified & directed.

S&F switch modular one way 6 Amps, 230 volts, 1 module. Make:- Legrand Mylinc Cat Part No 675501 or equivalent in Schneider/Havells/CG/ as approved.

S&F switch modular one way 16 Amps, 230 volts, 1 module. Make:- Legrand Mylinc Cat Part No 675511 or equivalent in Schneider/Havells/CG/ as approved.

S&F switch modular two way 6 Amps, 230 volts, 1 module. Make:- Legrand Mylinc Cat Part No 675502 or equivalent in Schneider/Havells/CG/ as approved.

S&F modular bell push 6 Amps, 230 volts, 1 module. Make:- Legrand Mylinc Cat Part No 675504 or equivalent in Schneider/Havells/CG/ as approved.

S&F modular socket 6/16 amps 2/3 pin combined 2 module. Make:- Legrand Mylinc Cat Part No 675555 or equivalent in Schneider/Havells/CG/ as approved.

S&F modular socket 6 amps 2/3 pin combined 2 module. Make:- Legrand Mylinc Cat Part No 675550 or equivalent in Schneider/Havells/CG/ as approved.

S&F modular hum free electronic step fan regulator ,100 watts 2 module. Make:- Legrand Cat Part No 675530 or equivalent in Schneider/Havells/CG/ as approved.

S&F TV co-axial modular socket 1 module. Make:- Legrand Mylinc Cat Part No 675546 or equivalent in Schneider/Havells/CG/ as approved.

S&F telephone socket double RJ-11, 1 module. Make:- Legrand Mylinc Cat Part No 675544 or equivalent in Schneider/Havells/CG/ as approved.

S&F power unit for AC or geyser 3.5 KW 4 module including sunken modular GI metal boxes not less than 1.2 mm thick and white modular mounting plates with frame Legrand Mylinc Cat Part No 675558, 689009, 675564 & 675584 or equivalent in Schneider/Havells/CG/ as approved.

M&L for sand filling in trenches with clean dry fine sand unwashed including gently punning around cables complete.

S&F in repairs energy efficient recessed mounted LED luminaries suitable for 2’x2’ grid ceiling with flat diffuser and lumen output of 3300 lumens having constant current electronic driver duly connected with 0.5 sq.mm white colour PVC insulated & sheathed three core flexible multi stranded copper conductor cable as required. Make-Philips cat ref No RC365B LED33-6500 PSU OD WH or equivalent in CG/Havells as approved.

Supply and laying old size bricks, common burnt clay building bricks sub class ‘B’ designation 75 laid in trenches over sand for cable protection complete

Schedule of Credit

UNIVERSAL INFRAPROJECT PVT LTD

GS BUILDERS AND ENGINEERS

Satish kumar and company

J.J.ENGINEERING

M/S Mohan Lal Gupta

Pioneer Enterprises

M/S Dinesh Chandra Mittal