Addn/Altn of 02 x single offrs accn at offrs mess Bldg No P 286) Provn of safety railing alongwith Periphery of polo ground and training area and Provn of cooling appliance and fan with electric point under Zone III area at Mil Stn under GE(S) Jaipur

Amount

JOB No : 52/LBW/61SA/20-21/Q3W (B/R) Excavation in trenches not exc.1.5 m wide and not exc.1.5 m in depth for foundation or for shafts, walls, manholes etc not exc.10 Sqm on plan and getting out in soft/loose soil.

M&L for PCC 1:4:8 type D2 using 40 mm graded stone aggregate in foundations, filling and mass concrete

M&L for brick work with subclass 'B' bricks, straight or curved on plan exc 6 m mean radius built in cement mortar 1:6

Brickwork with subclass‘B’ bricks, straight or curved on plan to any radius in half brick thick walls built in CM ( 1:4)

M&L for formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work, not exc 200mm thick (Horizontal or sloping) for fair finished flat surfaces of concrete.

M&L for formwork to edges of concrete flats, roofs, floors etc not exc 20cm wide and sides of RCC/PCC bands in walls, horizontal or sloping and similar work exc 10cm but not exc 20cm wide for fair finished surfaces.

M&L for reinforced cement concrete (nominal mix) 1:1½ :3 type A1 using 20 mm graded stone aggregate in lintels upto 1.5m clear span, seismic and other similar bands, lintel bands, plinth bands, roof bands and the like. Note :- Reinforcement & formwork shall be measured separately.

M&L for reinforced cement concrete (nominal mix) 1:1½ :3 type A1 using 20mm graded stone aggregate in slabs supported on walls, beams and columns in floors, roofs, shelves and the like. Note :- Reinforcement & formwork shall be measured and paid for separately.

S&F TMT bar 10 mm dia & over, cut to length, bent to shape required, including cranking, bending, spirally for hooping for columns, hooking ends and binding with and including MS wire ( annealed) not less than 0.9 mm dia as specified .

S&F TMT bar 6 to 8 mm dia, cut to length, bent to shape required, including cranking, bending, spirally for hooping for columns, hooking ends and binding with and including MS wire ( annealed) not less than 0.9 mm dia as specified .

All as per item No. 9 above but 6 to 8mm dia in stirrups, spacers and binders

Earth filling under floors including spreading, levelling, watering and well ramming in layers not exc 25 cm thick. Note :- Soil obtained from excavation under item 1 here-in-before shall be used for filling.

Returning,filling in, including spreading, levelling watering and well ramming in layers n.exc 25 cm soil.

Removal of excavated soil to a distance exc. 250m but not exc. 500m and depositing where directed.

M&L for 75mm thick PCC 1:4:8 type D2 using 40mm graded stone aggregate as in sub base to floor finished fair & even all as specified and directed by Engineer-in-charge.

M&L rendering 15 mm thick in CM(1:6) on brick walls or concrete surface, surface finished even and smooth without using extra cement complete all as specified.

M&L for rendering 10mm thick in cement mortar 1:4 on stone masonry surfaces in ceilings finished fair and even

M&L for rendering 15mm thick in cement mortar 1:4 on stone masonry surfaces or surface other than fair face of brick work of walls, finished fair & even.

M&L for preparation of new plastered surfaces and applying two coats of weather base paint of approved shade on walls over a coat of birla wall care putty and primer all as specified & directed by Engineer-in-Charge

M&L for preparation of new plastered surfaces and applying two coats of plastic emulsion paint of approved shade/tint over a coat of birla wall care putty on walls all as specified & directed by Engineer-in-Charge

M&L for preparation of new plastered surfaces and applying two coats of plastic emulsion paint of approved shade/tint over a coat of birla wall care putty on ceilings all as specified & directed by Engineer-in-Charge

M&L for 30mm ( average thickness ) PCC 1:2:4 type B0 using 12.5mm graded stone aggregate as in floors and surfaces finished fair & even.

M&L 15 mm thick screed bed or bedding layer of cement mortar 1:4 for laying floor finishes.

M&L for light shade vitrified ceramic tiles 10mm thick (square/rectangular) polished, area of each tiles not exceeding 0.36 sqm , in floors etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match all as directed by Engineer-in-charge.

S&F light shade Vetrified Ceramic tiles edge cut 10mm thick (square/rectangular) polished, area of each tiles not exceeding 0.36 sqm, in floors etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match over 10mm thick plaster in CM (1:4)

M&L for coloured Non Skid Ceramic tiles 7 to 8mm thick (square/rectangular) area of each tiles exceeding 0.11 sqm but not exceeding 0.18 sqm , in floors etc, laid over and laid 15 mm thick screed bed in CM 1:4 set and jointed in neat cement slurry and pointed in white or coloured cement to match all as directed by Engineer-in-charge.

S&F Coloured Glazed ceramic tiles size 350x450mm x 7mm thick edge cut on walls etc in the combination of light and dark shed concept . set & jointed in neat cement slurry & pointed in white/coloured cement to match over 10mm thick plaster in cement mortar (1:4)

M&L for surface preparation by removal of all loose particle to ensure clean, smooth and dry surface and laying 25mm thick PCC type B-0, (1:2:4) using 12.5mm graded stone aggregate finished even & smooth without using extra cement to cover negative slope into prop with WPC @ 3% weight of cement.

The surface shall be painted with one coat of polymeric primer @ 0.30 Kg per sqm, conforming to IS : 3384. A layer of APP based polymeric membrane, 3 mm thick (min), weighing not less than 3.5 Kg/m2 reinforced with polyster non woven fabric ( weighing not less than 150 gms/ Sqm). Application of polymeric membrane shall be by torch application all as per manufacturer instructions. and finally applying one coat of bitumen @ 1.2 kg/sqm on APP membrane before application of aluminum paint

M&L one coat of aluminum paint over APP Membrane all as specified and directed by Engineer -in - charge

Aluminum Powder coated frame for holding of two track sliding shutter fixed type with aluminium section weighing 0.75 Kg/Mtr( composite weight of frame, track and beading ) incl. necessary joining, cleats, glazing clips, rubber packing powder coated aluminum snap beading, screws etcand beading for fixing of galvanised wire wire mess complete all as specified

Aluminum powder coated door/window shutter openable/ sliding type with aluminum section weighing 0.40 Kg/( composite weight of frame and beading ) Mtr incl. necessary joining, cleats, glazing clips, rubber packing aluminium powder coated snap beading, screws, handle & tower bolt etc complete all as specified

S&F tinted glass 5mm thick, ordinary quality & glazing with rubber packing in square as required & directed by Engr - in - Charge

S&F Figured glass 5.0mm thick, pin head type & glazing with rubber packing in squares n. exc 0.5 sq.m in each pane

M&L of 35 mm thick of IInd class hard wood Plain framed panelled shutters (any numbers of panels ) with panels of timber flat on both sides (feather edged), or of veneered particle board with commercial face veneers supplied and fitted and fitted to chowkates

35mm thick IInd class hard wood factory made Glazed and skelton shutters open rebated & prepared to receive glass gauze etc (without sash bars) edges of framing plain chamfered / rounded fitted with cut & mitred beads for securing glass etc size of members as specified in SSR Part I,section 8, clause 8.24(a).

S&F plain, solid, straight chowkats and frames Ist class hard-wood ( Sal ), wrought, framed rebated on the solid rounded or chamfered, put together with glue, pinned at Joints.

M/L for Fancy type MS bracket suitable for curtain rod including taking down

M&l of 20 mm dia MS pvc coated Fancy type curtain rod including taking down

M/L for Fancy type caps/ side Bulbs PVC powder coated suitable for curtain rod

S&F elegent mirror PVC cabinet with towel rail of size 475 x 600 x 150 mm all as specified (Make : Paryag/ Commander)

S & F in repair Tooth brush holder/ Tumbler brass CP for putting bathroom utilities ((Make-CERA CAT PART NO CA 104or equivalent of MARC, JAQUAR)

Soap dish brass CP ((Make-CERA CAT PART NO CA 103 or equivalent of MARC, JAQUAR) fixed in repair

S&F PVC (SWR) pipes 75mm bore single socketed, in any length with rubber ring joints laid in trenches or in floors including taking down

S&F PVC (SWR) pipes 110mm bore single socketed, in any length with rubber ring joints laid in trenches or in floors including taking down

S&F PVC (SWR) bends any radius 75mm dia

S&F PVC (SWR) bends any radius 110mm dia

S&F PVC (SWR), junction single, (Single T) equal or unequal 75mm dia

S&F PVC (SWR), junction single, (Single T) equal or unequal 110mm dia

S&F PVC (SWR) vent cowl 110mm dia

M&L PVC (SWR) gully trap 125/110 mm, setting & jointing with solvent cement

S & F in repair Toilet paper holder of vitreous china fixed to walls with chromium plated (CP) brass screws(Make-CERA CAT PART NO CA 106 or equivalent of MARC, JAQUAR)

S&F bathroom Glass corner of best quality (as per sample kept in GE office)

S&F vitreous china wash down water closet pan ( Pedestal pattern ),white including connection to drain (or outgoing pipe) and to flushing pipe,anti-sypohonage pipe etc. & with plastic WC seat cover white closed pattern with flat bottom and cover and mild steel chromium plated or aluminised hinging device complete including Cisteren .( Make-EWC HINDWARE CAT PART NO 20053 TULIF or equivalent& CISTEREN HINDWARE CAT PART NO 21036 or equilant )

S&F in repair Vitreous China wash hand basin oval size white / coloured, size 610x560mm including CP waste coupling but excluding taps, waste chain & plug & ( Make-Make-CERA , HINDWARE/ PARRY WARE ),

S&F Waste fittings 32mm bore, brass, CP for glazed ware sinks, basins, etc. with long screwed shanks & fly-nuts, flange end bedded in red lead cement & other end fixed(Make-MARC CAT PART NO MAC 3020 or equivalentof CERA JAQUAR)

S&F in repair CP bottle trap with internal partition 32 mm size with 300 mm X 190 mm long wall connection pipe and wall flange for WHB (Make-MARC CAT PART NO MOR 1350 or equivalentof CERA JAQUAR)

S&F stop valve 15mm, . copper alloy, screwed down, high pressure with crutch or butterfly handle screwed both ends for iron pipe or for unions.

S&F in repair Stop valves 20 mm bore, . copper alloy screwed down high presure, with crutch of butterfly handle, screwed both ends for iron pipe or for unions

S&F in repair CP health faucet with long chain for EWC including flexible pipe for 15 mmdia bore of Make Cera, Jaquar

M&L of PVC Nahani / floor trap and square in size of 100X100 mm including MS chromium plated grating 125mm dia of weight not less than 50gm for floor trap / Nahani trap.( Make Paryag and equivalent approved make)

M&L in repair for new galvanised steel water tubing medium grade with all fittings and fixed complete to walls and ceilings or laid in floors of following sizes :-

15 mm bore

20 mm bore

S&F Rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) hoisted & fixed in position all as specified in SSR Part I 500 Ltrs Capacity Make . Polycon/ syntex etc fixed in repair.

S&F Ball brass valves 20mm bore, high pressure, with polythene float & flynut complete, screwed for iron pipe or brass ferrule fixed in repair.

M&L for providing circular, raised platform of height 15 cm below the tank and base 10 cm more than the external dia of thank of PVC cylindrical water tank of capacity 500/100 liters using PCC 1:3:6 type c1 using 20mm graded stone aggregate with smooth finish

M&L CP cast copper alloy bib taps two way with wall flange and areator fancy type of 15 mm bore quarter turn (Make-CERA CAT PART NO CQ 606or equivalent of MARC, JAQUAR) fixed in repair.

S&F PVC connection 15mm bore with 2 Nos PTMT nuts, 45cm long fixed with one end to pillar tap & the other end to stop cock or iron pipe all as directed by Engineer-in-charge. Make - PRAYAG/SIMET

M&L CP fancy Type center hole basin mixer 15mm bore cast copper alloy with 450 mm copper hose /braided hose without Popup waste system quarter turn (Make-CERA CAT PART NO CQ 615 or equivalent of MARC, JAQUAR) fixed in repair.

M&L CP wall Mixer with flange & 115 mm long bend pipe forover head shower non Telephonictype with connecting legs wall flanges and crutch etc quarter turn ( Make-CERA CAT PART NO CQ 612 or equivalent of MARC, JAQUAR) 15mm bore for mixing hot & cold water fixed in repair.

M&L Towel ring of brass CP Squar flange (Make-CERA CAT PART NO CQ 102 or equivalent of MARC, JAQUAR) fixed in repair.

M&L Chromium plated Overhead Rain shower with relvoling joint and 115mmlong shower arm with wall flange 15 mm bore fancy type any colour (Make-CERA CAT PART NO CP 140 or equivalent of MARC, JAQUAR) fixed in repair.

M&L Chromium plated angle stop cock with wall flange fancy type cast copper alloy 15 mm bore any colour (Make-CERA CAT PART NO CQ 608 or equivalent of MARC, JAQUAR)

S&F galvanised mild steel wire cloth 0.50 mm nominal dia of wire and average width of aperture 1.18 mm and fixed with tinned tacks or galvanised wire staples all as directed by Engineer- in -Charge.

S&F MS holdfast, hook and pintle hinges, large hasp and staples, clamps, hooks for hanging fans and similar small articles conforming to Fe-290 Gde E-165 including necessary welding etc. and fixed in position.

S&F 100 mm butt hinges medium weight cold rolled mild steel, ISI marked, fixed to angle iron chowkats including welding complete.

S&F brass, barrel tower bolts 150mm long of extruded section.

S&F brass sliding door bolt 300 mm long with hasp, staple (bolt type) & fixing clips of sheet, . or extruded sections & fixing bolts & sliding bolts of extruded sections.

S&F brass handles 125 mm size, . type, anodised

S&F brass body floor door stopper overall length 140 mm double legged with rubber shoe, fixed to bottom rail of door as directed.

Surface excavation not exc 30cm deep and averaging 15cm deep and getting out in soft/loose soil.

M&L for hardcore of broken stone or boulders, gauge not exc. 63mm, deposited, spread and levelled in layers not exc 15 cm thick, watered and rammed to a true surface all as directed.

M&L for PCC 1:3:6 type C1 using 20mm graded stone aggregate as in plinth protection, 50mm thick finished even and smooth without using extra cement.

Supply only Water proofing treatment compound

M&L of Two coats of French Polish on Untreated wooden surface including Touch wood two coats etc

Granite (of any type) work (table rubbed and polished) for wall lining (veneering to wall) 20 mm thick in cement mortar (1:3) and pointing with white cement (1:2) using marble dust with admixture of pigment to match with shade of granite.

Demolition of Brickwork or stone/boulder masonry, built in lime mortar including all quions, arches, pillars etc, but excluding ashlar facings, dressed stonework and precast concrete articles

Demolition of PCC in ground floors and pavings not exc 15cm thickness ( below or above ground level )

Taking down Chowkats or frames exc 1.5 sq. m but n exc 4 sq m each with shutters (without taking off shutters from the frames)

Taking down the existing unserviceable stop valve and S&F stop valve 15mm, . copper alloy, screwed down, high pressure with crutch or butterfly handle screwed both ends for iron pipe or for unions.

Dismantling of old U/S gratingand M&L of PVC Nahani / floor trap and square in size of 100X100 mm including MS chromium plated grating 125mm dia of weight not less than 50gm for floor trap / Nahani trap.( Make Paryag and equivalent approved make )

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises.

Taking down cement plaster including raking out joints, hacking for key scrubbing down with water etc built in CM

Providing and fixing 28mm thick factory made PVC Supreme Door Shutter consisting of frame made out of m.S. tubes of 19 gauge thickness nd size of 40mmx20mm for stiles, top and bottom rails having a coat of steel primers of approved make and manufacture. M.S. Frame covered with 4mm thick heat moulded "Rajshri" Prelam PVC 'C' Channel of size 28mm thickness,75mm width out of which 60mm shall be flat and 15mm shall be tapered in 45dgree angle on either sides forming stiles, top and bottom rail and 100mm wide Rajshri Prelam PVC sheet out of which 100mm shall be be flat and 15mm shall be tapered An additional of 5mm thick PVC sheet of 20mm width is to be stuck on the interior side of 'C' Channel using PVC solvent adhesive etc. complete on both sides to form lock rail.Lock rail shall be provided on either side of panel. Panelling of 4mm thick PVC sheet to be fitted in the MS Frame welded/sealed to the stiles with 8mm (4mm + 4mm) x 12mm wide PVC sheet as beading on inner side and 8mm (4mm + 4mm) x 20mm wide PVC sheet as beading on the inner tapered side of lock rails joined together with solvent cement adhesive. An additional of 4mm thick PVC sheet of 20mm width is to be stuck on the interior side of 'C' Channel using PVC solvent adhesive etc. complete as per direction of Engineer-in-charge.

Providing and Fixing Factory made Adjustable (PVC) Doorframe Manufactured by M/s Rajshri of the size 65mm x 60mm with a wall thicknes of 4mm, made out of extruded 4mm PVC foam sheet, metre cut at two corners and joined with 2nos. of 150mm long brackets of 15 x 15mm M.S. Square tube. The two vertical door profile are to be reinforced with 40 x 20mm M.S. tube of 19 guage through out the frame. The doorframe shall be fixed to the wall using 65/100mm long M.S. Screw through the frame by using PVC fastners. A minimum of 4 nos. of screws to be provided for each vertical member & minimum 2 nos. for horizontal member etc. complete as per manufacturers specification and direction of Engineer-in-Charge.

Providing and fixing suspended false ceiling using mineral fibre board of size 600 x 600 x 15mm as ceiling over and including suspension metal(galvanised iron) system ) designer grid (15mm grid 8mm return) bevelled tegular suprafine XL 15mm / silhouete complete including necessary hanging system arrangement 6 mm dia suspenders as per manufacture's instruction which is required to be made from existing RCC roof/stone slab of building complete all as specified and directed by Engineer-in-Charge. Make :- Armstrong(ANF RH 90) or equivalent make of Everest , Gypsum India Ltd, Bison and Aerolite.

JOB No : 70/LBW/61SA/20-21/Q3W Excavating in post holes (or similar holes) each n.exc 0.50 cum,getting out, and removing surplus soil to a distance n.exc 50 m and making good

M&L for providing cement concrete 1:3:6 type C1 (using 40mm graded stone aggregate) as in Foundation, Filling and mass concrete

S&F GI Pipes 150mm bore, Medium grade fixed in post holes for Safety railing complete all as specified and directed by engineer in charge

S&F GI Pipes 80mm bore, Medium grade fixed in between verticle pipes with all necessary drilling holes, fittings, welding etc for Safety railing complete all as specified and directed by engineer in charge

M & L Plain or corrugated steel sheets, any thickness in available size, black including necessary welding to safety railing pipes at top and bottom complete all as specified and directed by engineer in charge

M & L preperaing steel Surfaces of any description, over 10cm in width or girth, not otherwise described and applying two coats of synthetic enamel paint on steel surfaces over a coat of red oxide primer

M & L for washing and cleaning of galvanised surfaces and Preparing new galvanised surface to receive painting, by coating with modrant solution , etc. and applying two coats of synthetic enamel paint all as specified and directed by engineer in charge

ELECTRIFICATION JOB No : 52/LBW/61SA/20-21/Q3W M&L Point wiring complete with 1.5 Sqmm single core PVC insulated and unsheathed multi stranded copper conductor FRLS cable of 1100 V grade PVC insulated and unsheathed cable inclosed in and including concealed PVC conduit medium grade with all accessories ISI marked, including MS sunken box for mounting fitting like switches, sockets fan regulators modulor type etc. including 1.5 sqmm single core PVC insulated but unsheathed copper earth continuty conductor to common earth and connected FRLS cable 1100 V grade as continuous earth wire to earth dolly for followings Make- Havells(std)/Bonton/Polycab/HPL

One light/fan/ bell point controlled by one, one way switch.

One 3 pin 5 Amp socket outlet on independent board with other switches.

One three pin 5 Amp socket on same board with other switches.

All as per Item No 104.00 above but with 2.5 Sqmm copper cable for 3 pin 15 Amps socket outlet on independent board, including 2.5 Sqmm copper cable continuous earth wire and connecting to common earth dolly.

All as per Item No 104.00 above but with 4 Sqmm copper cable for 3 pin 15 Amps socket outlet on independent board, including 4 Sqmm copper cable continuous earth wire and connecting to common earth dolly. complete all as specified & directed by Engr-in Charge.

Supply & Fixing Switch moduler type on top covers (catered in point wiring above):- Make- Havells/Polycab/Anchor/C & S

Single pole, one way 6 Amp rating. 52/LBW/61SA/20-21/Q3W - 22 62/MIN/61SA/20-21/Q3W - 8

Single pole, one way 16 Amp rating. 52/LBW/61SA/20-21/Q3W - 454 62/MIN/61SA/20-21/Q3W - 2

S & F Socket outlet multipurpose use, on top covers (catered in point wiring above) :- Make- Havells (std)/Polycab/Anchor/C & S

5 Pin 6 Amp 52/LBW/61SA/20-21/Q3W - 1241 62/MIN/61SA/20-21/Q3W - 4

6 Pin 16 Amp 52/LBW/61SA/20-21/Q3W - 454 62/MIN/61SA/20-21/Q3W - 2

M&L Ceiling rose surface bakelite 65x50mm, three terminals.Make Anchor/Legrand/Crabtree 52/LBW/61SA/20-21/Q3W (E/M) - 4 62/MIN/61SA/20-21/Q3W (E/M) - 4

Supply & fix T5 integrted batten LED Light fittings 1 x 20 W ,240 volt( size-4 feet/1136 mm) long life, surface/wall mounting IP 20, luminaire per watt (Minium) extruded alluminium housing with frosted PMMA diffuser with high brightness LEDs complete with all accessories pre-wired twin core twisted flexible copper conductor cable with suitable size. Make - Crompton/Bajaj/Wipro/ Philips/CG /Surya roshni

Supply & fix wall Bracket light asthetically designed with B22 & E27 lamp holder including 10W LED Lamp with all accessories pre-wired twin core twisted flexible copper conductor cable with suitable size. Make - Halonix cat Pt No- HLBW-01-B22 or equivelent model in Bajaj/ Philips/Syska

Supply and Fixing security lights LED 40 W Energy saving & Environmental friendly long life versatile pressure die cast aluminium IP 66 LED Wall mounted Light Luminaries are made of die casted aluminium body and toughened glass cover for uniformlight spread cames LED technology of Britelite. including bracket made out of suitable size of GI medium grade tubing and fixed with clamps nuts and bolts, washer complete all as specified . Make- CG cat Pt No-LSTS-40-CDL or equivalant in HAVELLS ,Syska and Phillips

S &F ceiling fan 1200 mm sweep complet 5 star rating all as specified and directed Make: Havells, khaitan, Usha

S&F factory made, sheet distribution boards, SP&N 6 ways, double door protection class IP-42 double door type suitable for mounting MCB/ MCCB, confirming to IS-13032, IS-8623, BS-5484 with minimum 200 amps, copper bus bar of the under mentioned rating :-

S&F MCB 10 KA confirming to IS-8828 : 1996, IEC-898 : 1995 rupturing capacity of the under mentioned type and rating :-

(a) SP 5 to 32 amps

(b) SPN 32 to 63 amps.

M & L Sub main wiring complete with 2 runs of 6 Sqmm single core PVC insulated unsheathed cable 1100 V grade with multistranded copper conductor ISI marked drawn throughn and including PVC rigid conduit/casing capping and conduit accessories fixed on surface/wall celing etc including provision of 1 run of 4 Sqmm PVC insulated unsheathed cable with multistranded copper conductor as earth continuity.

Supply and fix sheet metal enclosure complete with metallic plug and socket heavy duty moduler type 3 pin (2P + Earth), 25 amp rating single phase 240 volts complete with MCB SP 25 amp “C” series (Make :Havells/HPL/Anchor/havells(std)

JOB No : 62/MIN/61SA/Q3W/20-21 M&L Point wiring complete with 1.5 Sqmm single core PVC insulated and unsheathed multi stranded copper conductor FRLS cable of 1100 V grade PVC insulated and unsheathed cable Enclosed in and including casing caping medium grade with all accessories ISI marked, including MS sunken box for mounting fitting like switches, sockets fan regulators modulor type etc. including 1.5 sqmm single core PVC insulated but unsheathed copper earth continuty conductor to common earth and connected FRLS cable 1100 V grade as continuous earth wire to earth dolly for followings Make- Havells(std)/Bonton/Polycab/HPL

One light/fan/ bell point controlled by one, one way switch.

All as per Item No 118.00 above but with 2.5 Sqmm copper cable for 3 pin 15 Amps socket outlet on independent board, including 2.5 Sqmm copper cable continuous earth wire and connecting to common earth dolly. complete all as specified & directed by Engr-in Charge.

Single pole and neutral enclosure with a two pin and earth plug and socket complete with one single pole MCB

S & F MCB SP, 240 volts 25 Amp complete

Sub main cable with two runs of single core 4 Sqmm, PVC insulated, multi stranded, copper cable drawing in and including PVC conduit 25mm dia, 1.5mm wall thickness complete with all accessories such as nickel plated steel saddles, screws including 1x 4.Sqmm PVC insulated multi stranded copper cable as continues earth wire connecting to common earth and earth dolly including taking down existing unserviceable cable complete all as specified and as directed by the Engineer-in-Charge.

Supply and fix water cooler electric driven (single phase) having approx storage capacity 80 litre and nominal cooling capacity of 40 Litres per hour stainlessteel body, stainless steel tank, audjustable cold water thermostat, aut cut out , voltage overload compressor protection, silent operation, complete all as specified and directed. Make Usha, Blue star and Voltas

Supply and fix refrigerator, electric driven (single phase), capacity more than 292 Litres.BEE 5 star rated inbuilt inverter for voltage protection complete all as specified and directed by Engr-in-charge Make- Samsung, Whirpool, Voltas

Supply & fix Air Circulator fans 230 volts single phase oscillating 450 mm sweep suitable for wall mounting. Make Havells/CG/Usha/Khaitan

M/S JALANDRA CONSTRUCTIONS