SPECIAL REPAIR TO CHANGING ROOM IN SWIMMING POOL AT CME

Amount

Taking down chowkats or frames with shutters (without taking off shutters from the frames) exc 1.50 sqm but n exc 4.0 Sqm each .

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) and removing rubbish off the premises complete all as specified and directed.

Demolition of cement concrete (unreinforced) in ground floor and paving n.exc. 15 cm thick below or above ground level complete all as specified and as directed.

M & L for PCC (1:4:8) type D-2 (using 40mm graded crushed stone aggregate) 75 mm thick as in sub base complete all as specified and as directed.

M & L joint free non-skid ceramic coloured tiles 7 to 8mm thick, grade BII, matt superior finish, first quality, area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm in floor etc set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15mm thick screed bed in cement mortar (1:6) complete all as specified and directed.

M & L for vitrified ceramic coloured tiles 10mm thick (square/rectangular) polished, area of each tiles exceeding 0.36 sqm but not exceeding 0.42 sqm in floor etc, set and jointed in neat cement sluurry and pointed in white or coloured cement to match over and including 15 mm thick screed bed in CM (1:6) complete all as specified and directed.

M & L for glazed ceramic coloured tiles in vertical surfaces of size 450x350x7 mm / 350x250x7 mm thick set and jointed neat cement slurry, pointed in white or colour cement to match the shade of tiles, over and including rendering 15mm thick in CM (1:4) complete all as specified and directed.

S & F 15mm bore steel water tubing medium grade galvanized with and including all fittings such as bend, tees, union etc and fixed complete to walls and ceilings or laid in floors including taking down existing u/s pipe complete all as specified and directed.

S & F 20mm bore steel water tubing medium grade galvanized with and including all fittings such as bend, tees, union etc and fixed complete to walls and ceilings or laid in floors including taking down existing u/s pipe complete all as specified and directed.

M & L for cutting chases, pining in making good to facings where required & pointing in cement mortar (1:3) to ends etc or edges of landings, steps cills, sunshades, shelves,lintels,etc and cutting chases for concealed water tubing and making good, cutting n.exc. 10cm girth in brick walls all as directed.

M & L for half staff ceramic urinal pastel coloured of size 720x485x310mm (Make – Hindware Cat No 60006 or equivalent approved make indicated in list of makes in tender) including Urinal toughned glass Partition (including grinding, polishing, rounding/moulding/chamfering edges), brass cp bottle trap, electric operated auto censor flushing arrangements (Make Hinduware Cat No.500963 or equivalent approved make indicated in list of makes in tender) complete including taking down old u/s one complete all as specified and directed

S & F 12mm thick toughned glass including grinding, polishing, rounding/ moulding /chamfering edges, sliding arrangement, aluminium channels, rollers as in partitions including necessary fixing clips complete all as specified and directed by Engr-in-charge.

S & F 15 mm bore bib tap, brass chromium plated with wall flange, fancy type with long shank and crutch handle, screwed down, screwed for iron pipe including taking down old u/s one complete all as specified. Make : Jaquar CONTINENTAL SERIES CAT No CON-047KN or equivalent model in Marc/ ESS-ESS as approved by GE.

M & L for coupled closet (Clover) snow white make Cera including P or S trap alongwith cistern dual flush complete set and soft close plastic seat cover complete all as specified and directed including taking down old wash down water closed pan of any description any size including taking down old u/s one complete all as specified. Make- CERA Cat. No. S1013115 S Trap / P Trap or equivalent model in Parry ware (Super fine), Hindware as approved by GE.

M & L 75 mm dia of outlet, PVC (SWR) floor trap, plain with grating including jointing with solvent cement to waste pipe fixed in cement concrete (1:2:4) type B-1 & tested complete, all as specified and directed including taking down floor trap/nahani trap of any description any size.

S & F under counter wash hand basin vitreous china coloured including CI bracket, 15mm dia polythene connection, 32mm dia chromium plated (CP) waste coupling chain and plug waste filling union and 32mm dia PVC waste pipe 90cm long, all necessary inlet outlet connections complete all as specified and directed. Make : Hindware Cat No. 10065 or equivalent model in Cera /Parryware/ Neycer as approved by GE.

M & L for 18 mm to 20 mm thick Granite (of any type work) (table rubbed and polished) in steps, jambs, pillars, window cill, cooking platform, both side polished including necessary cutting, rounding exposed edges fixed in walls and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite complete all as specified and directed.

M & L machine cut cuddappah stone slab 20-25mm thick over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and as directed.

S & F wall mount installation type, brass CP hand shower (Health Faucet) 15 mm bore with 1 meter long easy flex tube in chrome finish & wall hock including taking down old u/s one complete all as specified and directed. (Make - Jaquar Cat No. ALD-563 or equivalent model in Marc/ ESS-ESS as approved by GE.

S & F PVC connection 15mm size with PTMT nuts of length 450mm including taking down old u/s one complete all as specified and directed.

S & F brass CP pillar tap long neck with 450mm long braided hose chrome finish including taking down old u/s one complete all as specified and directed. Make - Jaquar Cat No.Code No DRC-37001 or equivalent approved make indicated in list of makes in tender.

S & F brass chromium Angular stop cock with wall flange of 15mm bore capstan head including taking down old u/s one complete all as specified and directed. Make - Cera Code No. F-2002201 or equivalent approved make indicated in list of makes in tender.

S & F 15mm bore concealed stop valve chromium fancy type, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for union including taking down old u/s one complete all as specified and directed.

S & F tubular towel rail Brass chromium plated, 20mm dia, D type, 60cm long between flanges including taking down old u/s one complete all as specified and directed.

Dismantling CI /AC /PVC (SWR) pipes of any description fixed to wall/ laid in trenches including making good disturbed portion of wall floor etc complete all as specified and directed.

Supply and fix PVC (SWR) pipe 110mm bore single socketed with rubber ring joints/ adhesive fixed to walls with PVC clamps / laid in trenches or in floors including taking down old u/s one complete all as specified and directed.

Supply and fix 110mm bore PVC (SWR) bend with access door any radius complete including taking down old u/s one complete all as specified and directed.

Supply and fix 110mm bore PVC (SWR) junction single (single Y) with access door equal or unequal complete including taking down old u/s one complete all as specified and directed.

Supply and fix 110mm bore PVC (SWR) junction single (single T) with access door equal or unequal complete including taking down old u/s one complete all as specified and directed.

Supply and fix PVC (SWR) pipe 75mm bore single socketed with rubber ring joints/ adhesive fixed to walls with PVC clamps / laid in trenches or in floors including taking down old u/s one complete all as specified and directed.

Supply and fix 75mm bore PVC (SWR) bend with access door any radius complete including taking down old u/s one complete all as specified and directed.

Supply and fix 75mm bore PVC (SWR) junction single (single Y) with access door equal or unequal complete including taking down old u/s one complete all as specified and directed.

Supply and fix 75mm bore PVC (SWR) junction single (single T) with access door equal or unequal complete including taking down old u/s one complete all as specified and directed.

S & F 15 mm bore bib tap, 2 in 1, brass chromium plated with wall flange, fancy type with long shank and crutch handle, screwed down, screwed for iron pipe including taking down old u/s one complete all as specified. Make : Hindware (Cat No : F200004FT) or equivalent approved make indicated in list of makes in tender.

S & F single flow, imported, overhead shower, brass chromium plated, screwed down, screwed for iron pipe including taking down old u/s one complete all as specified. Make : Hindware Cat 160004 or equivalent approved make indicated in list of makes in tender.

S & F Coat Hooks brass chromium plated (4 Hooks types) complete all as specified and directed. Make : Cera Bath Fitting Cat No F 5003112 or equivalent model in Marc/ ESS-ESS as approved by GE.

S & F Robe Hooks (2 Types) brass chromium plated fixed to wall including taking down old u/s one complete all as specified and directed. Make : Cera Bath Fitting Cat No F 5003108 or equivalent approved make indicated in list of makes in tender.

S & F Towel Ring brass chromium plated fixed to wall including taking down old u/s one complete all as specified and directed. Make : Cera Bath Fitting Cat No F 5003105 or equivalent approved make indicated in list of makes in tender.

Demolition of brick or stone/boulder masonary, built in cement mortar including all quoins, arches, pillars etc but excluding ashlar facings, dressed stone work and precast concrete articles and removal to store complete all as specified and directed.

M & L for block masonry with solid block of precast cement concrete class designation C-5 (using 20mm graded stone aggregate), exc 10cm in width and setting in cement mortar (1:6) complete all as specified and as directed.

M & L for 15mm thick cement plastering on stone masonry surfaces in CM (1:4) finished even and fair without using extra cement over and including 10mm thick dubbing out on irregular face of wall in CM (1:4) including taking down existing plastering of any description complete all as specified.

M & L for preparation of newly plastered or unplastered surfaces on wall surfaces and applying two coats of cement base paint complete all as specified and directed.

M & L for rendering 10 mm thick on ceiling in CM (1:3) finished even and smooth without using extra cement incl taking down old cement plaster all as specified and directed.

M & L for preparation of newly plastered surfaces and applying three coats of white wash on ceiling all as specified and directed.

M & L for complete scraping down of old decorative surface of walls with steel wire brushes of smoke spots, moulds, moss efflorecent salts including filling of spots with POP/Birla putty and making smooth surfaces and applying two coats of Luster over a coat of primer all as specified and directed by Engineer-in-Charge.

M & L for complete removal of existing treatment from walls, filling the holes/cavities and plastering in patches in CM (1:4), 15mm thick the surface required, cleaning and preparation of the surfaces and applying two coats of exterior emulsion paint 100% acrylic (Apex) over a coat of primers as per manufacturer's instruction complete all specified and directed. Note : The rate shall be quotted by the contractor including scafolding to carry out the work for height upto 10.00 mtrs.

S & F ISI marked, three layered, 1000 Ltr capacity rotational moulded polyethylene water storage tanks (Cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part-I including dismantling/demolition (PVC/RCC/Stone & PCC block masonry) of old unserviceable water tank of capacity exc 500 & nexc 1000 ltrs and 20mm bore dia of pipe ball brass valves, high pressure, with polyuthene float and flynut complete , screwed for iron pipe or brass ferrule and fixed including rubbish off debris beyond 100 m & n.exc 250 m complete all as specified and directed.

S & F stainless steel liquid soap dispenser with glass bottle complete fixed to wall complete including taking down old u/s one complete all as specified. Make- Cera Code No. F-5007111) or equivalent approved make indicated in list of makes in tender.

S & F stainless steel soap dish holder complete fixed to wall including taking down old u/s one complete all as specified. Make- Cera Code No. F-5006106 or equivalent approved make indicated in list of makes in tender.

S & F stainless steel toilet paper roll holder with flap complete including taking down old u/s one complete all as specified. Make- Cera Code No. F5006110 or equivalent approved make indicated in list of makes in tender.

S & F Glass Shelf 600mm long complete including taking down old u/s one complete all as specified. Make- Cera Code No. F5005301 or equivalent approved make indicated in list of makes in tender.

S & F Glass corners complete including taking down old u/s one complete all as specified. Make- Cera Code No. F5005103 or equivalent approved make indicated in list of makes in tender.

Taking down copper/aluminium point wiring (light, fan, socket or power) complete including fixture and fittings such as switches, ceiling roses, pendents regulators, sockets etc revoming materials to store for seperately) and making good disturbed surface of walls, floors etc complete all as specified and directed.

M & L for point wiring for light/fan/bell with FRLSH cable 1.5 sqmm PVC insulated (red for phase and black for neutral) unsheathed, multi stranded copper conductor 1100 volt grade in and including PVC casing/caping with all accessories and 1.5 sqmm green in colour PVC multistranded, copper conductor FRLSH cable for earth continuity connected to common earth dolly including MS sunken box/PVC box, surface/ flush type and modular white cover plate with frame complete all as specified and directed & making good to disturbed surface of wall etc complete all as specified and directed for the following:-

(a) One light/fan point controlled by one switch and regulator

(b) Socket outlet, three pin, 5 Amp, independent

(c) Socket outlet, three pin 5 Amps on the same board

M & L for point wiring for light/fan/bell with FRLSH cable 2.5 sqmm PVC insulated (red for phase and black for neutral) unsheathed, multi stranded copper conductor 1100 volt grade in and including PVC casing/caping with all accessories and 2.5 sqmm green in colour PVC multistranded, copper conductor FRLSH cable for earth continuity connected to common earth dolly including MS sunken box/PVC box, surface/ flush type and modular white cover plate with frame complete all as specified and directed for 6 pin 15 amps socket outlet flush type on independent board controlled by one switch & making good to disturbed surface of wall etc complete all as specified and directed.

S & F ceiling rose, surface bakelite suitable for 3 pin 230 volt 50 Hz AC supply complete all as specified and directed.

S & F Modular Switch one way and 6 Amp, 1 module, 230 volt complete all as specified and directed.

S & F Modular Switch one way and 16 Amp, 1 module, 230 volt complete all as specified and directed.

S & F Modular Socket outlet multipurpose having provision for 3 pin, 6 Amp and 2 pin, 6 Amp, combined 2 module complete all as specified and directed.

S & F Modular Socket outlet multipurpose having provision for 3 pin, 16 Amp and 3 pin, combined 2 module complete all as specified and directed.

Taking down exhust fan of any size/sweep after disconnecting the wire from existing ceiling rose and refixing the same after cleaning dust, oiling greasing etc including providing flexible three core from ceiling rose to connector of Exhust fan

Supply and fix PVC exhaust fan AC single phase 230/ 240 volts heavy duty of size 300 mm sweep, 1400 rpm, with louvers and all fixing arrangements such as plywood 18mm thick of suitable size all as specified and directed. Make: Havells heavy duty Model Turbo Force SP or any other equivalent approved.

M & L for sub main wiring with two runs of 4 sqmm single core multi stranded FRLSH PVC insulated and unsheathed copper conductor (red for phase and black for neutral) & one run of 4 sqmm single core multi stranded FRLSH PVC insulated and unsheathed copper conductor wire green coloured for earthing of grade 1100 V, FRLSH cable in and including electrical grade PVC conduit of desired colour and dia with complete accessories duly connected with earth dolly complete all as specified and as directed incl taking down old unserviceable one. Note: Two runs of 4 sqmm single core multi stranded PVC copper conductor,one run of 4 sqmm single core multi stranded PVC copper conductor and one run of PVC conduit shall be measured as one length for payment.

S & F Surface and wall mounted LED batten 20/22 watt, extruded aluminium housing provided for efficient heat dissipation with polycarbonate diffuser and integrated electronic driver for LED tube complete with retrofit LED energy saving recess/surface mounted luminaries, high efficiency diffuser for soft glare fee light of capacity 20 watt suitabe of operation on 230 volt 50 Hz AC supply complete all as specified and as directed by Engineer-in-charge. Make Cat Part No ENDURALINEARNEOBS20WLED865SPCWH of Havells or equivalent model in Wipro/HPL/Philips as approved by GE including taking down old u/s one complete all as specified.

Supply and fix lamp holder PVC insulated body with back plate suitable for batten complete for 230 volt 50 Hz AC supply complete all as specified.

S & F in replacement by flushing to walls MCB distribution board TPN 240 volts 4 way double door with 200 amps rated bus bar and making good to disturbed surfaces of floors walls etc complete all as specified and directed.

S & F in replacement by flushing to walls MCB distribution board SPN 240 volts 12 way double door with 200 amps rated bus bar and making good to disturbed surfaces of floors walls etc complete all as specified and directed.

S & F in replacement MCB SP 40 amps 230 volt 10KA type C complete all as specified and directed.

S & F in replacement MCB SP 6 to 32 amps 230 volt 10KA type C complete all as specified and directed.

M & L for earthing complete with Gl earth plate electrode 60 cm x 60 cm x 6 mm thick burried directly in ground ( earth pit not less than 2.25 m deep below GL ) with top edge of the plate not less than 1.5 m below the normal ground level connected with 4 mm dia (No. 8 SWG) by means of bolts, nuts, check nuts and washers of galvanised iron or steel including necessary excavation & earth work in any type of soil, removing surplus soil to a distance not exc 50 M, with and including PCC chamber in PCC (1 : 2 : 4), type B1, using (20 mm graded stone aggregate), mild steel frame made out of angle iron of size 40 mm x 40 mm x 6 mm thick duly painted with two coats of synthetic enamel paint over one coat of red oxide zinc chrome primer hinged with and including 6 mm thick Cl cover with handle , watering arrangement with funnel internally secured with wire mesh with 20 mm dia medium grade GI pipe for watering, 40 mm dia light grade, Gl pipe for lead protection with and including alternate layer of charcoal dust and common salt complete all as shown in electrical plate No 3 of SSR Part I connected to earthing test point all as specified and indicated including testing on completion including retrieving of old GI earth plate, CI cover, GI pipes, angle iron frame from existing earthing as directed.

Excavation in trenches n exc 1.5m wide and n exc 1.5m deep for laying /removing of cable and making good surface all as specified and directed by Engr-in-charge as in

(a) Soft/ loose soil

(b) Hard/ dense soil

(c) Soft/ disintegrated rock.

Returning filling in excavated soil in trenches, watering and well ramming in layers n exc 25 cm complete all as specified.

Removal of surplus excavated spoil to distance n exc 50 metre all as specified and directed.

Supply, laying and testing cable XLPE insulated, screened, pvc bedded, galvanised steel strip or wire armoured, electric power cables ( heavy duty) with stranded aluminium conductor 1100 volts grade in trenches/ passing through pipe/fixing on walls, floors etc incl using suitable clamp of cross sectional area 3.5 core 150 Sqmm including taking out old u/sone all as specified and directed.

Supply, laying and testing cable XLPE insulated, screened, pvc bedded, galvanised steel strip or wire armoured, electric power cables ( heavy duty) with stranded aluminium conductor 1100 volts grade in trenches/ passing through pipe/fixing on walls, floors etc incl using suitable clamp of cross sectional area 3.5 core 95 Sqmm including taking out old u/sone all as specified and directed.

Supply & Laying DWC (Double Wall corrugated) HDPE pipe ISI marked confirming to IS:16205 (Part-24) of outer dia of 120 mm and inner dia 103 mm polyethylene including coupler and bend with smooth internal and profiled external surface for non pressure under ground cable complete all as specified and directed by Engr-in- Charge. Make : REX POLYEXTRUSION LTD or equivalent make as approved by GE.

M & L for PCC (1:3:6) type C2 (using 20 mm graded crushed stone aggregate) for coping of poles/Panel/plinth blocks of LT poles etc including fair finishing the exposed surfaces even and smooth without using extra cement including necessary form work complete all as specified & directed.

M & L for PCC (1:4:8) type D2 (using 40mm graded stone aggregate) for foundation of poles/Panel complete all as specified and as directed.

Supplying and laying 80 mm bore GI tubing light grade incl all accessories for encasing cables for mechanical protection , laid under Plinth / Floors/ Paths Culverts or fixed on wall or concealed in wall/floor or along poles or as street light poles or as street light mounting bracket with complete accessories such as bends/sockets/reducers/saddles incl necessary threading/drilling works including taking down old tubing all as specified and directed. Note: MS works will be measured under seperate item in Schedule.

Supply & fix MCCB 400 Amp TPN, 415 Volts, 50HA, 50 KA for existing Panel at Sub Station No 3 for outgoing purpose for New proposed panel at Offr Institute CME all as specified and directed.

Supply, install, connect, test and commissioning factory made, dust/vermin, weather proof self ventilated, cubical of size 1.5 x 0.50 x1.2m (min) with front and rear opening, hinged door for front, and rear with MS angle iron frame 50 x 50 x 5mm for base support, 3.15 mm thick CRCA sheet, LT panel board, (LT KIOSK), out door, cubicle type, floor mounted, double door with neoprene gasket and locking arrangement with canopy with powder coating on steel surfaces internally & externally and provision of two Nos earth terminals on both sides, cable glands and PCC foundation with PCC (1:2:4), type B1, to accommodate and including the following accessories:-

(a) Aluminium bus bar rectangular 600 Amps full for phase and half for neutral and interconnection of MCCBs to Bus bar mounted on epoxy insulators with colour coding PVC sleeves.-01 job

(b) MCCB 400 Amps, TPN, 415 Volts, 50 Hz ,50 KA- 01 No ( Incoming)

(c) MCCB 250 Amps,TP, 415 Volts, 50 Hz ,36KA - 02 Nos ( Outgoing)

(d) MCCB 200 Amps,TP, 415 Volts, 50 Hz ,25KA - 02 Nos ( Outgoing)

(e) MCB TPN 40A - 02 Nos

(f) MCB SPN 32/40A - 02 Nos

(g) RYB LED Indicator Lamp- Set of Three -01 No

(h) Digital VAF+ Power factor meter Meter RS 485 CI .5

(j) Internal wiring of panel board, metering equipment with suitable size PVC insulated, unsheathed, 1100 V grade cable with multistranded copper conductor, including provision of lugs/thimbles on either ends of cable.

M & L for Earthing complete with galvanised steel earth plate electrode 600 x 600 x 6 mm thick, buried vertically in ground (Earth pit not less than 2.25 metres deep below normal ground level and top edge of the plate not less than 1.5 m below ground level), connected to and including Galvanised steel earthing galvanised iton strip of 25 x 4 mm by means of bolts, nuts & checknuts and washers etc; GI pipe 15 mm dia medium grade pipe for protection of G.I earth wire, both to be provided to the extent of 7.5 metres, all as shown on electrical plate No 3 of MES SSR-2009 Part-I, other end connected to electrical main switch board (inside the bldg) GI protection pipe buried in ground, laid under floors/plinths or fixed on walls or concealed in walls etc; with provision of mixture of charcoal dust & common salt packed upto minimum 150 mm all around the earth plate , including PCC (1:2:4) type B-1 earth pit with M.S angle iron frame, cast iron cover with locking arrangement, with G.I 20 mm dia medium grade pipe and M.S funnel with wire mesh for watering arrangement, including necessary excavation and earth work in any type of strata & testing on completion.

S & F three track sliding window with two or more shutter with 4 mm thick plane glass glass, one mosquito proofing shutter of stainless steel wire mesh 1.4mm dia & width of aparture 12mm with good quality bearing, handle, lock, rubber beading and glazing clips etc using following aluminium powder coated sections conforming to catalogue of 'JINDAL' or of equivalent make including taking down existing old window with frame of any description complete all as specified and directed by Engr-in-Charge. (a) Bottom frame 20620 (b) Top frame & vertical 20621 (c) Handle (side) 20606 (d) Shutter inter lock 20724 (e) Shutter top & bottom 20844

S & F aluminium anodised louvered ventilator with 4 mm thick, 100 mm wide pin headed glass strips and fixed with aluminium anodised frames etc including taking down existing old ventilator with frame of any description complete all as sspecified and directed. (a) SP 20048 (b) Glazing clips 19352

S&F aluminium colour powder coated anodised door and shutter single or double leaf glazed/pre laminated board exterior quality partly glazed//pre laminated board exterior quality party glazed panels fabricated including aluminium anodised beading rubber and packing materials and shall be drilling in existing wall and thrust bolt suitable size complete comprising the following:-

(a) Aluminium colour anodised door frame section 101.60x44.45x2.00 mm fixed as per spd

(b) Aluminium colour anodised vertical section in shutter 85x44.45x2 mm as per spd.

(c) Aluminium colour anodised Top & style shutter section 95.25x44.45x2.00 mm as per specified.

(d) Aluminium colour anodised handles 02 Nos and auluminium colour anodised 02 tower bolts in each shutter 200 mm long as specified.

(e) Aluminium colour anodised middle lock rail/bottom rail section 150x44.45x2.00 mm cat No.20002.Make-Jindal

(f) Floor spring. Make-ISI marked

(g) Six lever mortice lock brass Make : Godrej/Classic on in each door

(h) 12 mm thick particlular board (pre laminated both face) exterior grade ISI Marked at bottom panel of door

(j) Toughened glass (Plain, clear colour) 5mm thick Make : Saint gobain/ Modiguard at top panal of door

AJINKYA VIKRAM GAIKWAD

M/S JAYCONSTRUCTION CO

Aakar Construction