CERTAIN REPAIRS TO MARRIED ACCN, DEFENCE CIVILIAN ACCN AND MES KEY PERS COLONY KALINA AND JUHU UNDER GE (NORTH) SANTACRUZ

Amount

Demolition of reinforced cement concrete of any description (beam, chajja, fins, RCC water tank, roof sla etc) & in any position including necessary scaffolding arrangement (reinforcement cut as required to facilitate demolition) and removing concrete debris and depositing outside MD land all as specified and as directed by Engineer-in-Charge.

Supply and fix joists, channels,angle or tee sections, fixed independently, without connecting plates, etc. (cut to ordinary lengths i.e. within 20mm of the length indicated) framed work confirming to Fe-410- W(Gde E-250) quality B other section with gusset plate, rails, braces etc complete fastening and fixing complete all as specified and as directed.

Material and labour for preparing new steel surfaces of any description, over 10cm width or girth, not otherwise described and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and as directed by Engineer-in-Charge. Make: Make : Asian Paints/ Nerolac Paints/ Dulux ( Akzonobel)/ Nippon Paint India Pvt Ltd

Supply and fix Pre- painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick as per approved profile of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws or L type or J type or cranked hook bolts or as per manufacture instruction complete all as specified and as directed by Engineer-in-Charge Note- Work to be carried out for height upto 15 mt and above/ factory type bldg/Hanger) Make: JINDAL / INDALCO / HINDALCO / ASSOCIATED Profiles and Aluminium Ltd / ESSAR colour coated sheets

Demolition of brick work/stone masonry built in cement mortar or cement lime mortar including all quoins, arches, pillars, PCC coping etc, but excluding ashlar facings, dressed stonework and precast concrete articles and removing of debris outside MD land complete all as specified and as directed by Engineer-in-Charge.

Material and labour for brick work with sub class 'B' bricks, straight or curved on plan, exceeding 6 m mean radius, built in cement mortar 1:6 complete all as specified and as directed by Engineer-in-Charge.

Taking down chowkats or frames with shutter (without taking off shutter from frame) not exceeding 1.5 sqm each including fittings and removing clear off site after credit for the same is recovered by the dept complete all as specified and as directed .

Taking down shutter carefully, area exceeding 1.0 sqm but not exceeding 2.0 sqm each including fittings and removing clear off site after credit for the same is recovered by the dept complete all as specified and as directed .

Taking down chowkats or frames with shutter (without taking off shutter from frame) exceeding 1.5 sqm but not exceeding 4 sqm each including fittings and removing clear off site after credit for the same is recovered by the dept complete all as specified and as directed .

Supply & Fix Factory made single extruded WPC (wood polymer composite) soild door/ window/ ceosetory windows & other frames/chowkhat of size 65 x 100mm comprising of virgin PVC polymer of K value 58-60 (suspension grade), calcium carbonate and natural fibers (wood powder/rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with minter joints after applying PVC solvent cement and screwed with full body threaded star headed ss screws having minimum frame density of 750 kg/cum, screw withdrawal strength of 2200 N(face) and 1100 N(edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of class A catgory with property of being termite/borer proof water/moisture proof and fire resistant and fixed in position with MS hold fast/lugs/ SS dash fastners of required dia and length complete all as specified as directed by Engineer-in-charge. Note: M/S hold fast or SS dash fastners shall be paid for separately. Note: 1: For WPC solid door/window frames, minus 5mm tolerance in dimension i.e. depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made. 2. M/S hold fast or SS dash fastners shall be paid for seprately. Make: Rajashri/Giza/Echon/Floresta

Supply & Fix Factory made single extruded WPC (wood polymer composite) soild door/ window/ ceosetory windows & other frames/chowkhat of size 65 x 125mm comprising of virgin PVC polymer of K value 58-60 (suspension grade), calcium carbonate and natural fibers (wood powder/rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with minter joints after applying PVC solvent cement and screwed with full body threaded star headed ss screws having minimum frame density of 750 kg/cum, screw withdrawal strength of 2200 N(face) and 1100 N(edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of class A catgory with property of being termite/borer proof water/moisture proof and fire resistant and fixed in position with MS hold fast/lugs/ SS dash fastners of required dia and length complete all as specified as directed by Engineer-in-charge. Note: M/S hold fast or SS dash fastners shall be paid for separately. Note: 1: For WPC solid door/window frames, minus 5mm tolerance in dimension i.e. depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made. 2. M/S hold fast or SS dash fastners shall be paid for seprately. Make: Rajashri/Giza/Echon/Floresta

Supply & Fiix Factory made single extruded WPC (wood polymer composite) soild decorative type flush door shutter of size 35mm thick comprising of virgin PVC polymer of K value 58-60 (suspension grade), calcium carbonate and natural fibers (wood powder/rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) and having minimum density of 650 kg/cum, screw withdrawal strength of 1800 N(face) and 900 N(edge), minimum compressive strength of 50 N/mm2, modules of elasticity 850 N/mm2 and resisitance to spread of flame of class A catgory with property of being termite/borer proof water/moisture proof and fire resistant WPC to be laminated with pvc foil of minimum 14 microns thick of approved design pasted with hot melt adhesive on both faces of shutter and fixing with SS butt hinges of required size with necessary full body threaded star headed counter sunk ss screws complete all as specified as directed by Engineer-in-charge. Note: SS butt hinges and SS screws shall be paid seprately. Make: Rajashri/Giza/Echon/Floresta

Supply and fix 35mm thick factory made 2nd class hard sal wood glazed and skelton shutter, open rebated, prepared to receive glass, gauge etc (without sash bars), edges of framing plain chamfered or rounded, fitted with cut and mitred beads for securing glass etc sizes of members of shutter as specified in SSR Part-I section 8, clause No 8.24 (b) complete all as specified and as directed by Engineer-in-Charge. Make : M/S Goel Brothers, Raipur/ M/S Pioneer Timber, Chandigarh/ M/S Goyal Industries, New Delhi/ M/S Jain Doors Pvt Ltd, Haryana/ M/S India Wood & Wood P Ltd Mangalore/ M/S MP Wood Products, Indore

Supply and fix aluminium alloy wire cloth, 0.45mm nominal dia of wire and average width of aperture 1.40mm and fixed with aluminium wire staples complete all as specified and as directed by Engineer-in-Charge

Supply and fix in repairs aluminium alloy wire cloth, 0.45mm nominal dia of wire and average width of aperture 1.40mm and fixed with aluminium wire staples complete all as specified and as directed by Engineer-in-Charge

Material and labour for Prelaminated particle board 19/20mm thick, interior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination, fixed with screws to timber frame including taking down existing etc complete all as specified and as directed by Engineer-in-Charge. Make: Greenply / Kitply / Century Plywood / Associates Decor Ltd

Supply and fix 40mm dia, cupboard knobs fixed with nut, screw and washer of mild steel, bright finished complete all as specified and as directed by Engineer-in-Charge.

Material & Labour for IInd Class hard wood of size not exc 3 Sqcm, plain fillets, square, rectangular or triangular in section, clean sawn, secured with nails or brads complete all as specified and as directed by Engineer-in-Charge.

Supply and fix solid PVC door frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with 19mm x 19mm MS square tube EPDM rubber gasket weather seal to be provided through the frame, the profile shall be mitre cut at two corners and jointed by inserted 2mm of 150mm long bracket of 15mm x 15mm MS square tube inside the 19mm x 19mm MS square tube and suitable screwed the door frame shall be fixed to the wall using PVC fasteners. A minimum of 6 Nos screws to be provided for each frame as per specification & drawing on Serial Page No 180 of SSR Part II (pertaining to item No 08095) all as specified and as directed by Engineer-in-Charge. Note: The quoted rates are deemed to be included for cutting holes, providing concrete for hold fast and making good to the disturbed surfaces. Make: M/S Rajshri Plastiwood, Indore/M/S Sintex Industries Ltd/M/S TUFFFLON/M/S Dura Plast Extrusion

Supply and fix factory made solid panel PVC door shutter 30mm thick (style) consisting of frame, made out of M. S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC `C` channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded/sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, fixing in the frame at site as per specification & drawing on Serial Page No 176 of SSR Part II (pertaining to item No 08080) complete all as specified and as directed by Engineer-in-Charge. Make: M/S Rajshri Plastiwood, Indore/M/S Sintex Industries Ltd/M/S TUFFFLON/M/S Dura Plast Extrusion

Supply and fix mild steel work as in hold fast & similar small articles, conforming to Fe-290 Gde-E-165 complete all as specified and as directed by Engineer-in-Charge.

Supply and fix floor door stopper of aluminium alloy body and tongue, anodized with hard drawn steel spring 150mm size, complete all as specified and as directed. Make : Classic/ Shalimar/ CLIF/ARGET

Supply and fix Stainless steel butt hinges medium weight of size 100mm all as specified and as directed by Engineer-in-Charge. Make : Classic/ Shalimar/ CLIF/ARGET

Supply and fix Stainless steel butt hinges medium weight of size 125mm all as specified and as directed by Engineer-in-Charge. Make : Classic/ Shalimar/ CLIF/ARGET

Supply and fix aluminium anodised barrel tower bolt of extruded section size 150mm complete all as specified and as directed by Engineer-in-Charge. Make : Classic/ Shalimar/ CLIF/ARGET

Supply and fix extruded aluminium alloy handles fabricated types, anodised, of size 150 mm long complete all as specified and as directed by Engineer-in-Charge. Make : Classic/ Shalimar/ CLIF/ARGET

Supply and fix aluminium anodized sliding door bolt with hasp and staple (bolt type) and fixing clips of sheet cast or extruded section and fixing bolts and sliding bolts of extruded section or cast aluminium alloy 300mm long, ISI marked complete all as specified and as directed by Engineer-in-Charge. Make : Classic/ Shalimar/ CLIF/ARGET

Material and labour for plain cement concrete 1:3:6 type C-1 (using 20mm graded stone aggregate) as in lintels upto 1.5m clear span, cills, steps; seismic and other similar bands, plinth courses, holstring courses, lacing courses, parapets and railings upto 60 cm in height, copings, kneelers, apex stones, kerbs, water troughs, bed plates, concrete block for hold fast etc and the like including necessary form work for fair finished surfaces including weathering, slightly rounded or chamfered angles and throating, as directed etc complete all as specified and as directed by Engineer-in-Charge.

Dismantling floor hearth or wall tiling including cement mortar bedding ( but not backing), removing serviceable tiles to store and rubbish out side MD land complete all as specified and as directed by Engineer-in-Charge.

Material and labour for non skid coloured ceramic tiles, 7 to 8mm thick (square/rectangular), area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc., set and jointed in neat cement slurry and pointed in white or colour cement to match over and including screed bed of 20mm thick in Cement mortar 1:4 etc complete all as specified and as directed by Engineer-in-Charge. Make: M/s H R Johnson / M/s Kajaria / M/s Somany Tiles Ltd / RAK tiles/ Orient bell/Orient bell

Material and labour for coloured glazed ceramic tiles of size 350mm x 250mm x 7 mm thick/ 450mm x 350mm x 7mm (or nearest size) ,on vertical surface such as skirting, dado, riser/steps etc, set and jointed in neat cement slurry and pointed in white or colour cement to match over & including cement plaster 10mm thick in Cement mortar 1:4 complete all as specified and as directed by Engineer-in-Charge. Make: M/s H R Johnson / M/s Kajaria / M/s Somany Tiles Ltd / M/s Nitco tiles / RAK tiles/ Orient bell

Material and labour for light shade, vitrified tiles, 10mm thick (minimum), (square/ rectangular) polished, area of each tile not exceeding 0.36 sqm, in floors etc., set and jointed in neat cement slurry and pointed in coloured cement to match over and including screed bed of 20mm thick in cement mortar 1:4 including scarifying the floor complete all as specified and as directed by Engineer-in-Charge. Make: M/s H R Johnson / M/s Kajaria / M/s Somany Tiles Ltd / M/s Orient bell / M/s RAK tiles

Material and labour for light shade, vitrified tiles, 10mm thick (minimum), (square/ rectangular) polished, area of each tile not exceeding 0.36 sqm, on vertical surfaces etc, set and jointed in neat cement slurry and pointed in coloured cement to match including 15mm thick backing coat in cement mortar 1:4 complete all as specified and as directed by Engineer-in-Charge. Make: M/s H R Johnson / M/s Kajaria / M/s Somany Tiles Ltd / M/s Orient bell / M/s RAK tiles/ Orient bell

Demolition of stone slab and tiles of any description or thickness in floor, apron and vertical surfaces, laid bedded and pointed in any mortar and removing debris outside MD land complete all as specified and as directed by Engineer-in-Charge.

Material and labour for granite (of any type) , 20mm thick, machine cut (table rubbed and polished) in steps, jambs, pillars, window-cills, cooking platform, bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including necessary moulding of edges as required at site including grinding and polishing, over and including 15mm thick cement mortar (1:4) complete all as specified and as directed.

Material and labour for 20-25 mm thick machine cut cudappa stone slab as in cooking platform, laid and jointed with grey cement slurry, mixed with pigment to match the shade of slab including rubbing and polishing complete over backing coat/screed bed of 10 mm thick in CM (1:4)complete all as specified and as directed by Engineer-in-Charge.

Material and labour for 40 mm thick cement concrete (1:2:4) type B-1 using 20 mm graded stone aggregate as in flooring and finishing the surface even and smooth without using extra cement complete all as specified and as directed by Engineer-in-Charge.

Material and labour for providing Anti-termite Treatment with treating soil along with internal wall perimeter with chemical emulsion at the rate of 2.25 litre per linear metre including drilling and plugging holes etc complete all as specified and as directed by Engineer-in-Charge.

Material and labour for providing Anti-termite Treatment Treating at point of contact of wood work by chemical emulsion @ 0.5 litre per per hole by drilling 6mm dia holes at a downward angle of 45 degree at 150mm centre to centre and sealing the same etc complete all as specified and as directed by Engineer-in-Charge.

Supply & Fix Powder coated aluminium (minimum thickness of powder coating 50 micron) work for doors, windows, ventilators and partitions (Fixed portions) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS:733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc, aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-Charge. Make : Hindalco/Indal (Indian Al Coy)/Jindal/Associated Profile & Aluminium Ltd/Ajit India Note: (i) Glass panes /wire mesh will be measured & paid separately. (ii) Rubber beading will not be weighed.

Supply & Fix Powder coated aluminium (minimum thickness of powder coating 50 micron) for shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber/ neoprene gasket required (Fittings shall be paid for separately) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws all complete as per architectural drawings and the directions of Engineer-in-charge. Make : Hindalco/Indal (Indian Al Coy)/Jindal/Associated Profile & Aluminium Ltd/Ajit India Note: (i) Glass panes /wire mesh will be measured & paid separately. (ii) Rubber beading will not be weighed.

Supply & Fix Anodised aluminium grill (anodised transparent or dyed to required shade according to IS: 1868 with minimum anodic coating of grade AC 15) of approved esign/ pattern, with approved standard section and fixed to the existing window frame with C.P. brass/ stainless steel screws @ 200 mm centre to centre, including cutting the grill to proper opening size for fixing and operation of handles and fixing approved anodised aluminium standard section around the opening, all complete as per requirement and direction of Engineer-in- charge. Make: DECOGRILLE of Associated group / Royal Alum grill Pvt Ltd or equivalent make as approved by GE

Supply and fix 4.0mm thick glass, ordinary quality, in square, not exceeding 0.5 Sqm in each pane, fixed in aluminium windows complete all as specified and as directed by Engineer-in-Charge. Make : Modiguard/Atul/Kohinoor/Swastik/Saint Gobain

Supply and fix 4.0mm thick glass, ordinary quality, in square, exceeding 0.5 Sqm in each pane, fixed in aluminium windows complete all as specified and as directed by Engineer-in-Charge. Make : Modiguard/Atul/Kohinoor/Swastik/Saint Gobain

Supply and fix 4.0mm thick figured glass, pin headed type, ordinary quality, fixing with oil putty and glazing clip, in squares not exceeding 0.5 Sqm in each pane complete all as specified and as directed by Engineer-in-Charge. Make : Modiguard/Atul/Kohinoor/Swastik/Saint Gobain

Taking down cement plaster on brick or stone walls, ceilings etc. including raking out joints, hacking for key, scrubbing down with water and removing of debris outside MD land complete all as specified and as directed by Engineer-in-Charge

Material and labour for rendering 15 mm thick cement plaster in CM 1:4, two coats using factory manufactured pre mix/ready mix of 'Roofit Mix'of M/s Premier Floor to Roof Materials pvt.ltd/ 'Easy plast' of M/s Walplast Products pvt.ltd/ 'Readiplast' of M/s Ultratech Cement Ltd/'Soundplast PMC-1' of M/s Sound buildcare pvt.Ltd/ or other approved equivalent make, having minimum composition of C:S : 1:4 using fully treated dry, well graded natural sand conforming to IS 383 suitable for external plastering, having low rebound properties, low water demand for curing properties, mechnIcal mixing with water in a metalic tray only to make good consistency as per the specification of the Manufacturer and applied over exterior masonry and concrete surfaces with base coat of 10 mm thick and finishing coat of 5 mm thick final rendering with water proofing compound as per manufacturer's instructions, including using richer mix for making corners if necessary, at all floors and level, including making grooves of existing size wherever required,inclding sagol finish including cleaning the surfaces, curing including provide of 150mm chicken wire mesh fixed with nails at the junction of RCC columns/walls/ beams/ lintels and brick masonry at external faces before plastering including scaffolding at any height and all safety materials required for execute work etc. complete all as per specifications & as directed by the Engineer-in-Charge.

Material and labour for rendering 10mm thick on internal wall surfaces using factory manufactured pre mix/ready mix plaster of 'Roofit Mix' of M/s Premier Floor to Roof Materials Pvt Ltd/'Easy plast' of M/s Walplast Products Pvt Ltd/'Readiplast' of M/s Ultratech Cement Ltd' / Sound last PMC-1 of M/s Sound buildcare Pvt Ltd/or other approved equivalent make, having minimum composition of C:S : 1:3 using fully treated dry, well graded natural sand conforming to IS 383 suitable for plastering, having low rebound properties, low water demand for curing properties, mechanical mixing with water in a metallic tray only to make good consistency as per the specification of the Manufacturer and applied over masonry and concrete surfaces including dubbing of plaster of 10 to 15 mm thick for levelling purpose with same ready mix plaster and finishing with sagol finish not less than 1mm thick, including cleaning the surfaces, curing etc complete all as specified & directed by Engineer-in-Charge.

Material and labour for rendering 5 mm thick on ceiling using factory manufactured pre mix/ready mix plaster of 'Roofit Mix' of M/s Premier Floor to Roof Materials Pvt Ltd/'Easy plast' of M/s Walplast Products Pvt Ltd/'Readiplast' of M/s Ultratech Cement Ltd' / Sound last PMC-1 of M/s Sound build care Pvt Ltd/or other approved equivalent make, having minimum composition of C:S : 1:3 using fully treated dry, well graded natural sand confirming to IS 383 suitable for plastering in ceiling, having low rebound properties, low water demand for curing properties, mechanical mixing with water in a metallic tray only to make good consistency as per the specification of the Manufacturer and applied over concrete surfaces and finishing with sagol finish not less than 1mm thick, including cleaning the surfaces, curing etc complete all as specified & directed by Engineer-in-Charge.

Supply only integral water proofing compound ISI marked complete all as specified and as directed by Engineer-in-Charge. Make : Pidilite Industries Ltd, Taloja /Super Aquacem (India) Ltd /FOSROC/Siko/Dr Fixit

Material and labour for surface preparation of existing concrete components including grinding/rubbing carefully by grinder without damaging the existing concrete including cleaning the surfaces by blower , removal of external plaster wherever exists. Cost inclusive of transportation, labour conveying debris away from the Defence land, tools and tacklers, lead and lift and clean water thoroughly complete all as specified and directed by Engr-in-Charge.

Material and labour for providing and applying rust cleaner of approved make over prepared reinforcement, including removing concrete all around reinforcement including from behind the reinforcing bars by manual methods such as hammering the rebar, using wire brushes, chiseling, etc. and applying rust removing solution of approved make with cotton waste swab to reinforcements etc complete as directed by Engineer-In-Charge. Make- Dr FIXIT/ FOSROC/ Krishna Conchem/BASF/Sika

Material and labour for providing and laying 30 mm thick POLYMER MODIFIED MORTAR over identified R.C.C. members in One layer in proportion as per approved make, blended to a required consistency and applying and finishing by floating, curing after initial setting time, including providing and inserting 10 mm mild steel shear key bars (minimum 3 nos per sqm), wherever required, bonding slurry, etc complete all as specified and as directed by Engineer-in-Charge. Make- Dr FIXIT/ FOSROC/ Krishna Conchem/BASF/Sika as approved by GE.

Demolition of reinforced cement concrete of any description (beam, chajja, fins, RCC water tank, roof slab etc) & in any position including necessary scaffolding arrangement (reinforcement cut as required to facilitate demolition) and removing concrete debris and depositing outside MD land all as specified and as directed by Engineer-in-Charge.

Material and labour for providing and applying two coats of anticorrosive epoxy phenolic rebar protective system IPNet RB of Krishna Conchem or equivalent of approved make and quality comprises of resin and hardener mixed as per manufacturer's instructions with minimum 9-10 hours between the coats, sprinkling dry sand when 2nd coat is tacky so as to provide rough finish and ensuring air curing of minimum 10 hours after the top coat before any subsequent treatment etc. including scaffolding etc complete all as specified and as directed by Engineer-in-Charge. Make- Dr FIXIT/ FOSROC/ Krishna Conchem/BASF/Sika as approved by GE Note: (a) New Reinforcement shall be measured and paid separately under respective item. (b) Cost of welding deemed to be inclusive in this item of work.

Material and labour for providing and applying a priming cum bonding coat of two component Epoxide Resin conforming to ASTM-C-882-91 of approved make and quality to clean and sound concrete area by brush or any other established method by mixing base and curing agent 2:1 proportion by weight for joining old and new concrete as per technical specifications of manufacturer complete all as specified and as directed by Engineer-in-Charge. Make- Dr FIXIT/ FOSROC/ Krishna Conchem/BASF/Sika as approved by GE Note-Work shall be carried out as per the manufacturers specifications & certificate on this account shall be taken from consultant and as approved by Engineer-in-charge

Supply and fix mild steel TMT bars, 10mm dia and over, cut to length bent to shape required including cranking, bending spirally for hooping for columns hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips complete all as specified and directed by Engineer-in-Charge.

Supply and fix mild steel TMT bars, 6 to 8mm, cut to length bent to shape required including cranking, bending spirally for hooping for columns hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips complete all as specified and directed by Engineer-in-Charge.

Supply & fix MS/TS dowel pins/staple/shear pins including drilling holes in concrete and providing labour but excludeing the materials for grouting the pins etc complete all as specified and as directed by Engineer-in-Charge.

Material and labour for formwork using steel shutters or 12mm marine ply to have the smooth finish to pour the micro concrete/ concrete including de-shuttering etc complete all as specified and as directed by Engineer-in-Charge.

Material & labour for repairing of damaged concrete portion by using superfluid dual shrinkage compensated structural grade M-40 micro concrete of at all levels with all leads and lift as directed including mixing, laying, levelling, finishing and curing complete all as specified and directed by Engineer-in-Charge. Make: Fosroc / SIKA / BASF / Krishna Conchem or equivalent approved . Note for Item No. 51 to 61:- (i) The work under Item No. 42 to 45 shall be carried out by authorised applicator only. (ii) Defect liability for these items shall be 5 years from certified date of completion. (iii) Amount of 5% of these items shall be retained during RAR and FB. This amount shall be released after successful completion of Defects liability period as mentioned above. (iv) Non destructive testing shall be got carried out through IIT / NIT / College of Engineering Pune to decide fulfillment of fitness criteria of structure. (v) The test shall be carried out at each discrete location or locations decided by GE or testing authority. (vi)The cost of testing shall be deemed to be included in the rate quoted by the contractor. Completion shall be issued by GE after only getting structural stability certificate of each respective building from testing authority.

Material and labour for opening out cracks in wall surfaces in 'V' shape by mechanical grinder and removing the loose material. filling with crack filler of Dr. Fixit crack-X, shrink-free or equivalent all as per manufacturer's instructions and finishing the surfaces to match with existing finish complete all as specified and as directed by Engineer-in-Charge. Make- Dr FIXIT/ FOSROC/ Krishna Conchem/BASF/Sika as approved by GE

Material and labour for preparation of undecorated wall surfaces and applying 1.5mm wall care putty complete to smoothen the underneath surfaces complete all as specified and as directed by Engineer-in-Charge. Make: Asian Paints / Nerolac Paints /Jenson & Nicholson / Shalimar Paints / JK wall care putty

Material and labour for preparation of undecorated ceiling surfaces and applying 1.5mm wall care putty complete to smoothen the underneath surfaces complete all as specified and as directed by Engineer-in-Charge. Make: Asian Paints / Nerolac Paints /Jenson & Nicholson / Shalimar Paints / JK wall care putty

Material and labour for preparation of newly plastered surfaces of ceiling and applying three coats of white wash complete all as specified and as directed by Engineer-in-Charge.

Material and labour for preparation of newly plastered surfaces of wall and applying two coats of oil bound distemper with roller over a coat of alkali resistant wall primer complete all as specified and directed by Engineer in Charge. Make: Asian Paints (Tractor) / Nerolac Paints /Jenson & NIcholson / Shalimar Paints

Material and labour for new plastered wall surface and applying two coats of Acrylic weather proof coat 100% exterior grade paint over one coat of acrylic primer upto a height of bldg roof including formwork/scaffolding/ladders and safety belts with precautions etc complete all as specified and as directed by Engineer-in-Charge. Make : APEX ULTIMA” of Asian Paints/ “WEATHER COAT ALL GUARD” of Berger Paints/"EXCEL TOP GUARD” of Nerolac/ “DULUX WEATHERSHIELD MAX” of ICI India

Material and labour for preparing new wooden surfaces of any description, over 10 cm width or girth, not otherwise described and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and as directed by Engineer-in-Charge. Make : Asian Paints/ Nerolac Paints/ Dulux ( Akzonobel)/ Nippon Paint India Pvt Ltd

Supply and fix mild steel tubing medium grade 15mm, galvanized iron with all fittings such as Tees, elbows, sockets, bends, unions, short pieces, nipples, brass nuts and diminishing pieces complete all as per IS 1239 including fixed to wall / ceiling or laid in floor with suitable size GI clamps including cutting chases in brick walls pinning in if required and making good disturbed surfaces using with cement mortar 1:3 as per existing surfaces including taking down of old GI tubing with fittings complete all as specified and as directed by Engineer-in-Charge. Make: Tata / Jindal / Surya Prakash / Zenith

Supply and fix mild steel tubing medium grade 20mm, galvanized iron with all fittings such as Tees, elbows, sockets, bends, unions, short pieces, nipples, brass nuts and diminishing pieces complete all as per IS 1239 including fixed to wall / ceiling or laid in floor with suitable size GI clamps including cutting chases in brick walls pinning in if required and making good disturbed surfaces using with cement mortar 1:3 as per existing surfaces including taking down of old GI tubing with fittings complete all as specified and as directed by Engineer-in-Charge. Make: Tata / Jindal / Surya Prakash / Zenith

Supply and fix mild steel tubing medium grade 25mm, galvanized iron with all fittings such as Tees, elbows, sockets, bends, unions, short pieces, nipples, brass nuts and diminishing pieces complete all as per IS 1239 including fixed to wall / ceiling or laid in floor with suitable size GI clamps including cutting chases in brick walls pinning in if required and making good disturbed surfaces using with cement mortar 1:3 as per existing surfaces including taking down of old GI tubing with fittings complete all as specified and as directed by Engineer-in-Charge. Make: Tata / Jindal / Surya Prakash / Zenith

Supply and fix in repairs vitreous china wash hand basin white flat back size 550 x 400 mm excluding taps, waste chain and plug and porcelain stopper but including CI brackets, cutting for and pinning in ends of brackets or erecting stand including 32mm bore discharge pipe with waste coupling of PTMT etc complete all as specified and as directed by Engineer-in-Charge. Make : CERA/ RAK Ceramics/ Parryware/ Hindware/ Neyveli Ceramics (Neycer)/ Jaquar/ Kajaria (KEROVIT)

Supply and fix in repairs, sinks with drainage board made of stainless steel 1mm thick kitchen or laboratory with plugs, washers and wastes including bedding in cement mortar to dwarf wall or including fixing cantilever CI brackets and connecting union to pipe overall size 495mm x 420mm, bowl size 410mm x 330mm x 160mm including necessary fittings such 40mm coupling waste pipe etc complete all as specified and as directed by Engineer-in-Charge. Make : Diamond / Nirali / Neelkant/Parryware/Prayag

Supply and fix in repairs pillar taps fancy type , swan neck, cast copper alloy with capstan head, chromium plated, screwed down high pressure, with or without lettered ‘hot’ or ‘cold’ with long screwed shanks and fly nuts, screwed for iron pipes, 15mm bore complete all as specified and directed by Engineer-in-Charge. Make : Jaquar (Essco)/Prayag / Seiko/Prima

Supply and fix in repairs 15mm bore bib taps, fancy type, chromium plated, cast copper alloy, with crutch or butterfly handle screwed down, screwed for iron pipe or for brass ferrule all as specified and as directed by Engineer-in-Charge. Make : Jaquar/ Marc/ CERA/ Kohler/ Player

Supply and fix in repairs concealed stop valve, cast copper alloy, fancy type, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipes or for unions of 15mm bore complete all as specified and directed by Engineer-in-Charge Make : Jaquar/ Marc/ CERA/ Kohler/ Player

Material and labour for 15mm thick rendering in cement mortar (1:3) SUNKAN floor including with water proofing compound in sunken floor including vertical surfaces upto 450mm height including applying a coat of Raincoat solution of make Dr Fixit or equivalent with uniform surfaces and supply and fix vitreous china squatting pan Orissa pattern pan of size 580 x 440mm white with integral foot rest, 'P' trap and connecting to flushing pipe, anti syphonage pipe etc (excluding flushing cistern) and connecting piece of CI pipe as per required upto T/Y joint including filling PCC 1:4:8 type D2 and over 40mm thick PCC 1:2:4, type B0 for floor with uniform surfaces and GI spout, medium grade with 50mm dia to provide that 450mm long to be extended from front surface of wall all as specified and as directed.

Supply and fix in repairs vitreous china wash down, white, water closet pan (pedestal pattern) with 'P' of 'S' trap (of size 465mm x 355mm x 265mm),including plastic seat cover to match with colour of WC, closed pattern with flat bottom & cover and chromium plated mild steel or aluminium anodized hinging device including connecting to trap and flushing pipe, anti-syphonage pipe etc including health faucet (body cleaner) with 1.0m tube and hook (PVC tube) and toilet paper holder with flap guard complete all as specified and directed by Engineer-in-Charge. Make : Cera/Hindustan/Parryware/Jaguar/Hindware/Johnson

Supply and fix in repairs PVC valveless, syphonic action type low level flushing cistern 10 ltr capacity white with inlet ball valve, float and handle including brackets, flush pipe of polyethylene of low or high density or PVC 32mm dia including connection to pipe and fixing of chains and pull or lever complete all as specified and as directed. Make : M/S Johnson Peddar/ Parryware/ RAK Ceramics/ CERA

Supply and fix in repairs PVC (SWR) floor trap outlet dia 75mm, plain with gratings including jointing etc complete all as specified and as directed by Engineer-in-Charge. Make : Prince / Finolex / Supreme/Astral

Supply and fix in repair, health faucet (ABS body) mild steel chromium plated suitable for 15mm dia pipe with 1.25m long flexible tube and ABS wall hook, including making connection and fixed in position complete all as specified and as directed by Engineer-in-Charge. Make : CERA/ Hindustan/Parryware/Jaguar/Hindware/ Johnson

Supply and fix in repairs PVC (SWR), type B, single socketed rain water/soil waste/vent pipes with rubber ring joints, 110mm dia, fixed to walls complete all as specified and as directed by Engineer-in-Charge.. Make: Prince / Supreme / Finolex

Supply and fix in repairs PVC (SWR), type B, single socketed rain water/soil waste/vent pipes with rubber ring joints, 75mm dia, fixed to walls complete all as specified and as directed by Engineer-in-Charge.. Make: Prince / Supreme / Finolex

Supply and fix in repairs PVC (SWR) bends any radius, 110mm dia complete all as specified and as directed by Engineer-in-Charge Make : Prince / Supreme / Finolex

Supply and fix in repairs PVC (SWR) bends any radius, 75mm dia. complete all as specified and as directed by Engineer-in-Charge Make : Prince / Supreme / Finolex

Supply and fix PVC in repairs (SWR) vent cowl 110 mm dia complete all as specified and as directed by Engineer-in-Charge. Make : Prince / Supreme / Finolex

Supply and fix PVC in repairs (SWR) vent cowl 75 mm dia complete all as specified and as directed by Engineer-in-Charge. Make : Prince / Supreme / Finolex

Supply and fix PVC (SWR) branch piece, single (single Y) equal or unequal of any radius 110mm bore with access door etc complete all as specified and as directed. Make :Supreme/ PRINCE (Ultrafit)/ Kisan/ Finolex/ Astral

Supply and fix PVC (SWR) branch piece, double (double Y) equal or unequal of any radius 75mm bore with access door etc complete all as specified and as directed. Make :Supreme/ PRINCE (Ultrafit)/ Kisan/ Finolex/ Astral

Supply and fix in repairs rotational molded polyethylene water storage tanks 1000 litres capacity with inlet connections, three layer (cylindrical or vertical with closed top) HDPE with ISI marked, hoisted and fixed in position either inside or out side of the building, including fixing accessories and connecting up pipes securing access covers etc complete all as specified and directed by Engineer-in-Charge Make : Sintex / Polycon, Jaipur / Rotex / Infra

Supply and fix in repairs Ball Valves high pressure of PTMT with epoxy coated aluminium rod & high-density plastic ball screwed for iron pipe and fixed of 25mm bore complete all as specified and as directed by Engineer-in-Charge (Minimum weight - 142 gms) Make- Jaypee /GMP / Neta/ Zolota/Prayag Polymer/ Symet

Supply and fix in repairs gun metal gate valve, 25mm bore, with iron wheel head, screwed both ends for iron pipes, ISI marked and fixed with suitable size of new union complete all as specified and as directed by Engineer-in-Charge. Make : Leader/Zoloto/Seiko/Sant/GEM

Note: Deduct Credit for demolished / dismantled material of Rs. (-) 43,020.00 (Minus) as listed in Schedule of Credit. Tenderers will not quote against this item being a tentative amount to be considered to arrive at the 'Contract Sum'

Parmatma Enterprises (BID ID -3458529)

MAHESH ENTERPRISES (BID ID -3463934)