E-NIT for Re-carpeting of Metalled Roads of 220 KV GSS BBMB Hisar

Amount

Recarpetting of mettaled road

Tack Coat @ 0.40kg per sqm Providing and applying tack coat with penetration grade bitumen VG-10 using bitumen pressure distributor at the rate of 0.40 kg per sqm on the prepared bituminous surface/granular surface treated with prime coat after cleaning the surface complete as per technical specifications Ref. 24.16 (b) of (Pb. CSR-2020)

Patch Work with Bituminous Macadam 50mm to 75mm thickness (Grading II)Providing and laying patch work with bituminous macadam 50mm to 75mm thick using crushed stone aggregates of specified grading premixed with bituminous binder VG-30 @ 3.4% in Continuous type hot mix plant, carriage of mixedmaterial to site of work, laid after trimming the pot hole, removal of failed material, laying by suitable means and rolling with a smooth wheeled roller to match the adjoining surface complete as per technical clause 504 of MORT&H specifications Ref. 24.36(a) of (Pb. CSR-2020)

Open graded premix surfacing 20mm thickness - Providing, laying and compaction of open – graded premix surfacing of 20 mm thickness consisting of crushed stone aggregates of specified gradingpremixed in a Continuous type hot mix plant with bituminous binder VG-30 @ 1.46kg per sqm, laid with Paver Finisher Mechanical and rolling with a smooth wheeled roller 8-10 tonne capacity, finished to required level and grades complete as per technical clause 510 of MORT&H specifications Ref. 24.25 (b)of (Pb. CSR-2020)

Seal Coat Type B Providing and laying of premix sand seal coat premixed in Continuous type hot mix plant using specified fine aggregates and penetration grade bitumen VG-30 @ 0.68kg per sqm, laid to the specified levels, grade and cross fall complete as per technical clause 511 of MORT&H specifications Ref 24.28 d of (Pb. CSR-2020)

Road Safety Equipments

Road Marking with Thermoplastic Compound Road marking with hot applied thermoplastic compound 2.5mm thick including reflectorizing glass beads @ 0.25kg per sqm area as per IRC:35 1997 complete as per technical clause 803 of MORT&H specifications Ref. 24.57 of(Pb. CSR-2020)

Moulded Shank Road StudSupplying and fixing of single mould twin shank reflective road studs made out of poly carbonate/ABS moulded body and reflective panels with micro prismatic lens or Glass Beeds capable of providing total internal reflection of the light entering the lens face with retro reflectance and chromaticity values shall be as given in the detailed specifications and the product shall conform to ASTM D4280. The raised pavement marker shall also meet all the testing conditions of ASTM D4280 and fixed to the road surface using the adhesive. Two cylindrical Polymer Shanks of not less than 20 mm diameter and not less than 30 mm length shall be moulded in the RPM body. The marker shall support a load of 13635 Kg tested in accordance with ASTM D4280. The marker shall withstand flexural strength of 909 kgf force in accordance with ASTM D4280. Marker lenses shall be moulded of Polycarbonate or methyl methacrylate conforming to ASTM D788. The supplier shall provide a 2 years warranty for satisfactory field performance as per clause 804.7.3 of MORT&H 5th revision specifications Re. 24.63 of(Pb. CSR-2020)

Road Delineator/Vertical Guide Post Delineator Providing and fixing of Standard Metal Delineator as per IRC 79:2019 consisting of retro reflective area in white colour using full cube corner micro prismatic non-metallic retro reflective sheeting on each side conforming with IRC 67 2012 and meeting the coefficient of retro reflection values as per ASTM D 4956 Type XI table specification. The delineator shall be painted with only black colour powder coat of minimum 40 microns thickness, on top of which retro reflective sheeting only in white colour shall be pasted on both sides. The structure shall have height not less than 800 mm above the ground, width not less than 100 mm and shall extend not more than 300mm below the ground while being installed. The delineator shall have grooves across the length to make the reflective sheets vandal-proof. The delineator is Meant for application on gaps in median, traffic islands, dangerous bends, roundabouts, narrow bridges etc. or as desired by site engineer. Ref24.66(Pb. CSR-2020)

Cautionary sign board 600x600x600mm triangularas per IRC 67- 2012 with high intensity Micro prismatic grade retro reflective Sheeting as per ASTM D 4956 – 09 and as per IRC 67 – 2012. fixed over 3mm thick aluminium Composite material (ACM) sheeting having aluminium skin thickness of 0.25 to 0.3 mm on both sided and fixing the same with suitable size aluminium alloy rivets @ 200 mm c/c to back support frame of 25x25x3mm angle iron supported on a square hollow steel section post 60x60x3.2mm conforming to IS 4923 without cost of definition plate firmly fixed to ground in foundation concrete M-25 of size 0.45x0.45x0.60m for vertical post complete as per clause 801 of MORT&H Specifications. Supplier shall provide a warranty as per clause 6.9 of IRC 67-2012 for retro reflective sheeting & a certified copy of test reports from an independent test laboratory conforming to clause 6.7 of IRC 67-2012. (Ref. CSR 24.44)T/Rb (i) Using high intensity Micro prismatic grade retro reflective Sheeting Type IV as per ASTM D 4956 09 and as per IRC 67 2012 Ref. 24.44 T.R of(Pb. CSR-2020)

Mandatory sign board 600mm circular as per IRC 67- 2012 with high intensity Micro prismatic grade retro reflective Sheeting as per ASTM D 4956 – 09 and as per IRC 67 – 2012. Fixed over 3mm thick aluminium Composite material (ACM) sheeting having aluminium skin thickness of 0.25 to 0.3 mm on both sided and fixing the same with suitable size aluminium alloy rivets @ 200 mm c/c to back support frame of 25x25x3mm angle iron supported on a square hollow steel section post 60x60x3.2mm conforming to IS 4923 without cost of definition plate firmly fixed to ground in foundation concrete M-25 of size 0.45x0.45x0.60m for vertical post complete as per clause 801 of MORT&H specifications. Supplier shall provide a warranty as per clause 6.9 of IRC 67-2012 for retro reflective sheeting & a certified copy of test reports from an independent test laboratory conforming to clause 6.7 of IRC 67- 2012 . (i) Using high intensity Micro prismatic grade retro reflective Sheeting Type IV as per ASTM D 4956 09 and as per IRC 67 2012( No Parking -2 No Speed limits -4 No ) '24.45 bb(i) of (Pb. CSR-2020)

Advance Direction sign board 1200x900mm rectangular as per IRC 67- 2012 with high intensity Micro prismatic grade retro reflective Sheeting as per ASTM D 4956 – 09 and as per IRC 67 – 2012. fixed over 4mm thick AluminiumComposite Material (ACM) sheeting having aluminium skin thickness of 0.4 to 0.5 mm on both sided and fixing the same with suitable size aluminium alloy rivets @ 200 mm c/c to back support frame of 25x25x3mm angle ironsupported on two square hollow steel section post 60x60x3.2mm conforming to IS 4923 firmly fixed to ground in foundation concrete M-25 of size .60x0.60x0.75m for vertical post complete as per clause 801 of MORT&H specifications. Supplier shall provide a warranty as per clause6.9 of IRC 67-2012 for retro reflective sheeting & a certified copy of test reports from an independent test laboratory conforming to clause6.7 of IRC 67-2012 .( i ) Using high intensity Microprismatic grade retro reflective Sheeting Type IV as per ASTM D 4956 09 and as per IRC 67 2012 Ref 24.48 b i of( Pb. CSR-2020)

NS item

Providing and fixing of Plastic speed breaker 50 mm×1 mtr. Length in 4 pcs.

Providing and fixing of Bollard with solar 900x300mm &600mmcircle retro Reflective tape type 4 on 3mm ACP sheet & fitted on 25x25x3 MS angle frame MS Tube round frame retro HIP tap type iv on 3mm ACP sheet 900*300 mm & back side 25*25*3 mm angle frame with MS holo round/square tube 50mm appx. Dia 8 feet length fitted &fitted 4” solar delineator fitted on top of bollard

Providing and fixing of Convex mirror 80cm dia with MS holo round/square tube 50mm appx. Dia, 8 feet length including solar flasher light on top I

Providing and fixing reflector Tree guard /reflector 3 to 4 “dia appx. Plane

Bidder Name

Amount in Words

PRITAM KUMAR CONTRACTOR

Kewal Krishan Chawla Contractor

VINOD SAHARAN CONTRACTOR

M/s Bhambhu Builder Contractor & Supplier

Kewal Krishan Chawla Contractor

PRITAM KUMAR CONTRACTOR

M/s Bhambhu Builder Contractor & Supplier