SPECIAL REPAIR TO TOILET EXTERNAL FASCIA OF MOUT BUILDING NO P 170 AT NAVAL DOCKYARD UNDER GE NW KUNJALI COLABA, MUMBAI

Amount

Demolition of brick work or stone/boulder masonry, built in cement mortar including all quoins, arches, pillars etc but excluding ashlar facings, dressed stone work and precast concrete articles and disposing off complete all as specified and directed by Engineer-in-Charge.

Material and Labour brick work with sub class B bricks straight or curved on plan to any radius built in CM 1:6 complete all as specified and directed by Engineer-in-Charge.

Material and Labour for brick work with sub class 'B' bricks , straight or curved on plan to any radius in half brick thick wall built in cm 1:4 complete all as specified and directed by Engineer-in-Charge.

Taking down cement plaster of any description hacking for key, racking out joints and scrubbing down with water etc to receive plaster and removing debris outside MD land incl necessary scaffolding complete all as specified and directed by Engineer-in-Charge.

Material and Labour Plastering 15mm thick in CM 1:6 on brick surfaces, finished with Neeru finish on walls complete all as specified and directed by Engineer-in-Charge.

Material and Labour Plastering 5mm thick in CM 1:3 on concrete surfaces as in ceiling finished even & smooth without using extra cement in ceiling complete all as specified and directed by Engineer-in-Charge.

Material and Labour rendering 20mm thick on brick work or concrete surfaces in cement mortar 1:4 finished even and fair including mixing integral water proofing compound in the proportion as mentioned in manufacturer's instructions complete all as specified and directed by Engineer-in-Charge. (Water proofing compound to be measured and paid for separately).

Supply only integral water proofing compound complete all as specified and directed by Engineer-in-Charge.

Material and Labour for rendering 20 mm thick pre polymer modified ready mixed cement based plaster in two coats 12 mm thick base coat and 8 mm thick finishing/final coat. Polymer modified ready mixed cement based plaster should be having minimum composition of cement & sand 1:4 using fully treated dry, well graded natural sand conforming to IS-383 suitable for external plastering having low rebound properties, low water demand for curing properties, mechnical mixing with water in a metalic tray only to made good, consistency as per the specification of the manufacturer and applied over exterior masonry and concrete surfaces incl using richer mix for making corners if necessary incl making grooves of existing size and necessary two legged MS pipe scaffolding as wherever required incl curing required upto G plus 5th floor bldg complete all as specified and directed by Engineer-in-Charge.

Material and Labour for rendering 10 mm thick pre polymer modified ready mixed cement based plaster on chajja top and soffits, Polymer modified ready mixed cement based plaster should having minimum composition of cement & sand 1:4 using fully treated dry, well graded natural sand conforming to IS-383 suitable for external plastering having low rebound properties, low water demand for curing properties, mechanical mixing with water in a metalic tray only to made good, consistency as per the specification of the manufacturer and applied over exterior masonry and concrete surfaces incl using richer mix for making corners if necessary incl making grooves of existing size and necessary two legged MS pipe scaffolding as wherever required incl curing required upto G plus 5th floor bldg complete all as specified and directed by Engineer-in-Charge.

Taking down chowkats or frames but n exc 1.5 sqm each but with shutters (without taking off shutters from the frame) complete all as specified and directed by Engineer-in-Charge.

Taking down chowkats or frames exc 1.5 sqm but n exc 4 sqm with shutters (without taking off shutters from the frame) complete all as specified and directed by Engineer-in-Charge.

Supply and Fixing Solid PVC frame (Single Rebated) of size 60mm x 30mm made out of solid PVC foam with homogenous fine cellular structure having smooth outer integral skin with suitable metal stiffner and fixed with 100 x 8 sheet metal CSK screws complete all as specified and as shown on drawing (Note :- Door frame shall be water proof, termite proof, elegant and should have excellent screws holding strength to fix hinges and hold doors properly for a long life) in opening as per specifiecation and drawings complete all as specified and directed by Engineer-in-Charge.

Supply and Fixing 30 mm thick Rajshri brand factory made moulded door shutter wood free consisting of frame made out of MS tubes of 19 gauge thickness and size of 20 mm x 40 mm for stiles as well as top, bottom Material and Labour lock rail. MS frame shall have a coat of metal primer of approved make & manufacturer. The inside panel shall consist of 20 mm thick multichamber hollow PVC section of 1 mm wall thickness, bonded using solvent cement/cyanoacrylate adhesive with 5 mm thick moulded PVC sheet of density 600 Kg/Cbm manufactured by an ISO - 9001-2015 certified company with 2, 4, 6 raised panel design in plain/prelam colours after routing the moulded design on one side of the inside panel 5mm plain /prelam PVC sheet to be pasted using solvent cement /cyanoacrylate adhesive on other side of the hollow PVC section. All the four edge of the panel to be sealed with lipping of 10 mm thick & 20 mm wide PVC sheet baton (made by sticking 2 Nos foam PVC sheets of 5 mm thickness using PVC solvent cement adhesive. Door edge lipping to be painted with PVC ink of matching colour of plain/prelam moulded PVC sheet of door 20 mm thick (5 mm x 4 Nos ) thick PVC sheet to be given for lock provision at lock height . Door to be fixed with frame with 3 Nos stainless steel butt hinges of size 100 mm x 25 mm x 2 mm and 50 mm long steel screws drilled suitable to pass through both the walls of the MS tube other hardwares should be fixed with 20 mm x 8 mm size steel screws etc complete manufacturer's specification and drawing complete all as specified and directed by Engineer-in-Charge.

Dismantling stone slab and tiles of of any description or thickness laid bedded and pointed in any mortar in floors, aprons complete all as specified and directed by Engineer-in-Charge.

Material and Labour 20 mm thick Granite (of any type) work (table rubbed and polished) as in steps, jambs, pillars, window- cills,cooking platforms, working table and like over 20 mm thick screed bed or bedding layer in cement mortar (1:4), including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite complete all as specified and directed by Engineer-in-Charge.

Material and Labour for 20 mm thick granite maching cut as in skirting/vertical surfaces i.e jambs /risers and pillars etc and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including grinding, polishing and 10 mm thick backing coat in cement mortar 1:3 complete all as specified and directed by Engineer-in-Charge. (colour of granite will be decided by the GE/Engr-in-Charge).

Material and Labour for machine cut cudappa stone slab 20-25 mm thick over and including 15 mm thick cement screed base in CM 1:4 laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab incl rubbing and polishing complete all as specified and directed by Engineer-in-Charge.

Supply and Fixing powder coated aluminium (minimum 25 micron thickness of coating) of various section as required for doors, window & partion/Ventilator etc including fixing and making the frames hinges to receive glass/wire gauge etc. Complete incl all fittings like rubber beading, clips locking arrangement, handle, tower bolt for shutter, sealant complete all as specified and directed by Engineer-in-Charge.

Supply and Fixing aluminium grill with and including suitable aluminium anodised frame F/H section as requird manufactured by M/S Decogrill as per design No DG- 104, 7.5 mm thick all as complete all as specified and directed by Engineer-in-Charge.

Supply and Fixing aluminium alloy wire cloth 0.45mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel stapple complete all as specified and directed by Engineer-in-Charge.

Supply and Fixing 300 mm long aluminium alloy, sliding door bolt with hasp & staple (bolt type) and fixing clips of sheet cast or extruded section and fixing bolts and sliding bolts complete all as specified and directed by Engineer-in-Charge.

Supply and Fixing for aluminium anodized barrel tower bolts 200 mm of extruded section and fixed complete all as specified and directed by Engineer-in-Charge.

Supply and Fixing for aluminium anodized barrel tower bolts 150 mm of extruded section and fixed complete all as specified and directed by Engineer-in-Charge.

Supply and Fixing 150 mm size aluminium alloy handles, fabricated type extruded section, ISI marked complete all as specified and directed by Engineer-in-Charge.

Supply and Fixing 100mm size aluminium alloy handles, fabricated type extruded section, ISI marked complete all as specified and directed by Engineer-in-Charge.

Supply and Fixing butt hinges 100 mm mild steel hinges medium weight and fixed complete all as specified and directed by Engineer-in-Charge.

Supply and Fixing butt hinges 75 mm mild steel hinges medium weight and fixed complete all as specified and directed by Engineer-in-Charge.

Material and Labour for MS flat for hold fast. Conforming to Fe-290 Grade E 165 complete all as specified and directed by Engineer-in-Charge.

Hacking out old broken glass (any thickness, size, quality or description) from iron frames glazed with putty or wooden beads complete all as specified and directed by Engineer-in-Charge.

Supply and Fixing 3mm thick sheet glass frosted or obscured one side and glazing with oil putty or wooden beads in square area n.exc 0.5 Sqm in each pane complete all as specified and directed by Engineer-in-Charge.

Complete removal of existing treatment on wall surfaces by scrapping, washing & rubbing down including applying applying two coats of oil bound distemper over a coat of primer complete all as specified and directed by Engineer-in-Charge.

Material and Labour for preparation of old decorated surfaces of wall and applying two coat of oil emulsion distemper complete all as specified and directed by Engineer-in-Charge.

Material and Labour for applying 1 to 2 mm thick wall care putty for making the surface even & smooth complete all as specified and directed by Engineer-in-Charge.

Material and Labour for preparation of New Plaster surface or old decorated surface of ceiling and applying one coat of oil emulsion distemper complete all as specified and directed by Engineer-in-Charge.

Complete removal of existing treatment on ceiling surfaces and applying two coats of oil emulsion distemper over a coat of primer on ceiling surfaces incl preparation of surfaces complete all as specified and directed by Engineer-in-Charge.

Material and Labour Existing treatment of old decorated surfaces or new plaster Surface of walls soffits, facia roof and applying two coat of weather proof acrylic based paint (100% acrylic) over one coat of cement base primer with necessary scaffolding for high rise bldgs upto G+9 floor complete all as specified and directed by Engineer-in-Charge.

Dismantling floor, hearth or wall tiling including cement mortar bedding ( but not backing), removing serviceable tiles to store and disposing the rubbish to the out side of MD land complete all as specified and directed by Engineer-in-Charge.

Taking down PVC wastage and rainwater pipes (any size or pattern), including all fittings, heads, shoes, bends, swan-necks, complete all as specified and directed by Engineer-in-Charge.

Supply and Fixing 160mm dia bore PVC (SWR) pipes single socketed, in any length with rubber ring joints, fixed to walls complete all as specified and directed by Engineer-in-Charge.

Supply and Fixing 160mm dia bore PVC (SWR) bends any radius complete all as specified and directed by Engineer-in-Charge.

Supply and Fixing 110 mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls complete all as specified and directed by Engineer-in-Charge.

Supply and Fixing 75 mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls complete all as specified and directed by Engineer-in-Charge.

Supply and Fixing 110 mm bore PVC (SWR) bends any radius complete all as specified and directed by Engineer-in-Charge.

Supply and Fixing 75 mm bore PVC (SWR) bends any radius complete all as specified and directed by Engineer-in-Charge.

Taking up or down existing GI water tubing complete with all fittings of 15 mm bore complete all as specified and directed by Engineer-in-Charge.

Taking up or down existing GI water tubing complete with all fittings of 20 mm bore complete all as specified and directed by Engineer-in-Charge.

Supply and Fixing GI tubing medium grade with all fittings like Tee, bend, elbow etc, 15 mm bore fixed to walls or ceilings with saddles/spacers complete all as specified and directed by Engineer-in-Charge.

Supply and Fixing GI tubing medium grade with all fittings like Tee, bend, elbow etc, 20 mm bore fixed to walls or ceilings with saddles/spacers complete all as specified and directed by Engineer-in-Charge.

Material and Labour Bitumen membrane 3 mm thick laid on a coat of bitumen primer @ 0.30 to 0.50 Kg per Sqm in floors /sunken slab complete all as specified and directed by Engineer-in-Charge.

Material and Labour Apply evenly a tack coat of industrial bitumen 85/25 at the rate of 1.2 kg per sqm including cleaning surface complete all as specified and directed by Engineer-in-Charge.

Material and Labour for nominal mixed cement concrete 1:7:12 Type F2 with 40mm graded coarse aggregate complete all as specified and directed by Engineer-in-Charge.

M/L PCC 1:3:6 type C-2, 40mm aggregate 100 mm thick as in sub base for sunken slab/floor complete all as specified mixed with WPC 3% by weight of cement, finished even and smooth without using extra cement complete all as specified and directed by Engineer-in-Charge.(WPC shall be measured and paid separately).

Treatment of sunken floor slab comprising of the following specifications and all as specified :- (i) Material & labour for cleaning the sunken/lowered portion of RCC slab surface (including vertical total depth plus skirting height) of floors by wire brush, chisel out any mortar sticking to the surface and brooming completely 40 mm thick avg PCC (1:2:4) type B-0 using 12.5mm graded aggregate as in padding concrete to achieve proper slope including cutting holes in bricks or RCC wall for spout (Cost of cutting holes and pipes shall be measured and paid separately) (ii) Rendering of uneven surfaces with 6mm thick CM (1:4) mixed with integral water proofing compound @ 3% by wt of cement consumed. Fill it with water and check dampness and seepage. Where dampness/seepage is noticed, nozzles shall be fixed and grouting to be carried out. (WPC shall be measured & paid separately) (iii) All junctions points of side wall where CI/GI pipes are passing through shall be sealed with epoxy putty. (iv) After drying putty, wash the slab and sides of sunken portion with water and make it clear and clean. (v) Material & labour for applying two coats of polymer modified cementious water proof coating as per manufacturs instruction to bottom and vertical sides up to finished floor level+100mm height. The thickness of two layer shall be 1mm. When the second layer is still sticky, coarse sand spray shall be carried for the vertical and bottom surface of the sunken portion all as specified and directed.(This item shall be measured and paid separately) (vi) Plaster the bottom and sides up to bottom of the skirting with minimum 20mm thick CM (1:4) mixed with integral water proofing compound 3% by wt of cement consumed as per manufacturer's specification including rounding of corners and junctions sloping towards spout.( WPC shall be measured & paid separately) Note :- Test the water proofed area (ponding test) by filling water for at least 72 hours and shall be tested for leakage seepage and to the entire satisfaction of GE. Test shall be done in presence of reps of PMG and record for each sunken slab shall be maintained. The treatment shall be carried out by authorised applicators of chemicals. Cost of testing shall be deemed to be included in the rates complete all as specified and directed by Engineer-in-Charge.

Supply and Fixing in repairs Vitreous China wash down water closet pan ( pedestal pattern) , white (excluding fixing bolts, flushing cistern and flush pipe) fixed in repairs complete all as specified and directed by Engineer-in-Charge.

Supply and Fixing in repairs water closet squatting pan (Orissa pattern) 580x440mm, white with integral foot rests including connecting to trap and to flushing pipe antisyphonage pipe including making good to floor (excluding flushing cistern and flush pipe) complete all as specified and directed by Engineer-in-Charge.

Supply only cast iron 'P' trap 100mm dia complete all as specified and directed by Engineer-in-Charge.

Supply and Fixing in repairs fancy type CP Pillar taps 15 mm dia, cast copper alloy , with capstan heads, screwed down high pressure ,with long screwed shanks and fly-nuts , screwed for iron pipe and fixed complete all as specified and directed by Engineer-in-Charge.

Supply and Fixing in repairs fancy type bib taps, chromium plated cast copper alloy 15mm bore with crutch or butter fly handle, screwed down, & fixed complete all as specified and directed by Engineer-in-Charge.

Supply and Fixing in repairs fancy type angle valve chromium plated cast copper alloy 15mm bore with crutch or butter fly handle complete all as specified and directed by Engineer-in-Charge.

Supply and Fixing in repair wash hand basin vitreous china white (flat back) of size 550x400mm including bracket 15mm dia 32mm dia waste coupling and 32mm dia PVC waste pipe 90cm long complete all as specified and directed by Engineer-in-Charge.

Supply and Fixing PVC connections 15 mm size with PTMT nuts of length 600mm complete all as specified and directed by Engineer-in-Charge.

S/F in repairs PVC valveless syphonic action type ,flushing cistern Low level white, with inlet ball valve ,float and handle 10 Ltr capacity including brackets complete all as specified and directed by Engineer-in-Charge.

Supply and Fixing in repairs Flush pipe of Polyethylene of low or high density or PVC 32 mm dia. for low level cistern complete all as specified and directed by Engineer-in-Charge.

Supply and Fixing in repairs Soap dish any type fixed to plugs with chromium plated brass screws complete all as specified and directed by Engineer-in-Charge.

Supply and Fixing vitreous china urinal, half stall type white (excluding flushing cistern, flush pipe ) but including PVC waste pipe , providing and fixing plugs bedding urinal against wall in cement mortar 1:2 securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement and fixing automatic flushing cistern with brackets, flush pipe, grating and union for discharge pipe. (exclusive of fixing supply pipe to flushing cistern trap and waste pipe) fixed in repair complete all as specified and directed by Engineer-in-Charge.

Supply and Fixing Vitreous China urinals, bowl type (back or corner wall type), complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement; fixing automatic flushing cistern with brackets, flush pipe, grating and Union for discharge pipe. (Exclusive of fixing supply pipe to flushing cistern, trap and waste pipe) complete all as specified and directed by Engineer-in-Charge.

Dismantling water tank of capacity exc. 250 Ltrs but n.exc. 500 ltrs complete all as specified and directed by Engineer-in-Charge.

Supply and Fixing rotational moulded polythylene water storage loft tank tank of 375 ltr capacity hoisted including 20 mm bore ball valve high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball screwed for inron pipe and fixed (minimum weight 210 grms ) all as specified in SSR Part I. complete all as specified and directed by Engineer-in-Charge.

Supply and Fixing in repairs 20 mm bore ball valve high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball screwed for iron pipe and fixed (minimum weight 210 grms) complete all as specified and directed by Engineer-in-Charge.

Supply and Fixing in repairs PVC modular section 20mm thick as in profile including 'C' channels, aluminium all around the profile complete all as specified and directed by Engineer-in-Charge.

Supply and Fixing in repairs, Plastic water closet seat, black or white closed pattern with flat bottom, and cover and mild steel chromium plated or aluminised hinging device complete all as specified and directed by Engineer-in-Charge.

Supply and Fixing in repairs door closer hydraulically regulated, designation No 2, universal type, suitable for door shutters of 701 to 850 mm in width and of weight between 36 to 60 Kg and fixed complete all as specified and directed by Engineer-in-Charge.

Demolition of cement concrete (unreinforced) in ground floor and in paving not exceeding 15 cm thickness (below or above ground level) complete all as specified and directed by Engineer-in-Charge.

Material and Labour Providing plain cement concrete type B-1, 1:2:4 (using 20 mm graded stone agg) as in lintels upto 1.5 M clear span, cills, steps, seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railing upto 60 cm in height, copings, kneelers, apex stones, bed plates, bed blocks, roof kerbs water troughs and the like including weathering slightly rounded or chamfered angles and throating complete all as specified and directed by Engineer-in-Charge.

Material and Labour for rolled mild steel section as in main and cross beams, hip and jack rafters; purlins where connected to common rafters and running rails and guides for sliding doors ; fixed with angle cleats or other connecting plates conforming to grade Fe 290 (Gde-E-165) incl one shop coat of red oxide primer and two coats of synthetic enamel paint incl preparation of surfaces complete all as specified and directed by Engineer-in-Charge.

Supply and Fixing in repair roller/venetian blinds vertical/horizontal type made out of standard cloth of approved texture with necessary accessories complete all as specified and as directed

Material and Labour for 4mm thick bakelite sheet with decorative choice laminated on both side complete all as specified and directed by Engineer-in-Charge.

Supply and Fixing in repairs CP towel rail 600 mm long with round flange (Make - Jaquar CAT PART NO -CAN-1111NM) complete all as specified and directed by Engineer-in-Charge.

Supply and Fixing in repairs health faucet ABS Body with 8 mm dia 1 mtr flexible tube and wall hook (Make - Jaquar CAT PART No-ALD-CHR-585) complete all as specified and directed by Engineer-in-Charge.

Supply and Fixing 600 mm glass self assembly fancy type with CP frame (Make - Jaquar CAT PART NO AKP-35771P) fixed with chromium plated brass brackets and screw complete all as specified and directed by Engineer-in-Charge.

Supply and Fixing Vitreous china urinal partition white of size 310x700 mm complete all as specified and directed by Engineer-in-Charge.

Material and Labour 32mm dia waste coupling, PTMT for glazed ware sinks, basin, etc with long shanks and fly, flange end.complete all as specified and directed by Engineer-in-Charge.

Material and Labour for chipping, removing carefully concrete work by low impact hammer breaker without damaging the structure & cleaning and disposal of debries out side the premises etc complete as directed by Engr-in-Charge, hard concrete should not be removed by force including necessary scaffolding for high rise bldgs complete all as specified and directed by Engineer-in-Charge.

Material and Labour for clean existing reinforcement with wire/rotary wire brush, making the surfaces free from loose material dirt etc complete applying two coats of alkaline rust converting primer FEOVERT confirming to ASTM-B-117, on the rebars, including cleaning the reinforcement wire brushing to remover loose rust spalls with time interval of 6 hour between the coats and applying protective coating IPNET-RB complete all as specified and directed by Engineer-in-Charge.

Material and Labour for replacement of steel reinforcement with TMT bars of appropriate size where 20% of cross section is reduced including dismantling of rusted steel including application of rust converter FEOVERT and applying protective coating IPNET-RB complete all as specified and directed by Engineer-in-Charge.

Material and Labour for carry out application of Bi-polar migratory corrosion inhibitor EPCO-KP-100/Protectsil CIT/Ferogard 903 on concrete surface (This inhibitor shall have migratory kind of properly which permits the material to migrate to a vertical extent of 100 mm through pores of concrete, inhibiting the corrosion and de-passivating the Electro-chemical reaction. It should have properly to attack anode as well as cathode, which is purely alkaline in nature (pH-9.5) so it has non carcinogen activity with concrete complete all as specified and directed by Engineer-in-Charge.

Material and Labour for providing and applying structural grade EPIBOND-21-LP prior to application of any type of mortar plaster confirming to ASTM-C-882-91 (Arizona Slant Shear Test) to ensure bond between old concrete and new concrete complete all as specified and directed by Engineer-in-Charge.

Material and Labour for Building up the profile of structural members by using latex additives(MONOBOND) modified air cured mortar system (Polymer modified mortar) (1:5:15 = 1 monobond-5Cement-15 sand) -in damaged areas in 30mm thickness including leveling profliling and scaffolding for high rise buildings complete all as specified and directed by Engineer-in-Charge.

Material and Labour for Providing and applying jacketing around columns/RCC members with Micro concrete (Molith-MC) M30 including all lifts, shuttering, drilling holes and fixing shear anchor as per specification complete.Note: Reinforcement shall be measured and paid separately.(Rates including jacketing, formwork and micro concrete) complete all as specified and directed by Engineer-in-Charge.

Material and Labour for Drilling and fixing Rohibb Teflon nozzles in RCC members, including drilling holes of 12mm dia, 50 to 100mm deep holes in structural members at the intervals of 500 center to center in staggered manner complete all as specified and directed by Engineer-in-Charge and as directed in RCC structural element. Work shall be carried out as under :- (i) Cleaning of holes. Clean the holes by air blower prior to fixing nozzles. (ii) Fixing of nozzles. Insert 12mm dia. Rohibb Teflon nozzles in cleaned holes. External end of nozzles to be machine to receive outlet of grouting gun.Fix it inside the holes by applying thixotropic epoxy putty to ensure complete sealing. Cure the system for min.12 hrs. (iii) Cutting of nozzles. Cut the nozzles by chisel after completion of grouting without damaging structural elements.

Material and Labour for Injecting of site cement slurry grout, in the ratio 1:2 (1- Cement, 2-water) including super plasticizer (Supercom-100) 250 ml/50 Kgs. Mixing shall be done by mechanical mixer continuously stirring mechanically to keep cement particles in suspension. Injection of approved/specified grout by means of pump at a pressure of 0.5 Kg/cm2 etc complete till the grout mix flows out from the nozzle indicating complete filling of grout in the holes drilled. (for repair to wall & slab) complete all as specified and directed by Engineer-in-Charge.

Material and Labour for Injecting low viscosity MONOPOL (3-5cps) high molecular weight monomer by pressure and using mechanized injector gun with accessories till nozzles refuses to accept the grout, Including,Mixing of materials:Mixing of material components(part a&b) in the required quantities as per manufacturer's instruction by weigh batching.Grouting maintain the pressureat exit(0.5 to 1.0 kg/cm2) by monitoring pressure guage at exit.Grout the material through prefixed nozzles in the structural elements@ 100ml per nozzle. Repeat the process for all the nozzles. (Beam and columns) complete all as specified and directed by Engineer-in-Charge.

Material and Labour for 100 mm thick cement concrete 1:4:8 type D-2 (40 mm graded stone agg) as in sub base complete all as specified and directed by Engineer-in-Charge.

Material and Labour 25 mm thick cement concrete type B-1 , 1:2:4 (20 mm graded stone agg) as in hardstanding laid in alternate panel complete all as specified and directed by Engineer-in-Charge.

Material and Labour cement concrete tiles 25 cm x 25 cm x 22 mm thick, machine pressed (with grey cement and pigment), set jointed and pointed in neat cement slurry in floors and cut and polished over & including 15 mm thick bedding layer in cement mortar 1:6 complete all as specified and directed by Engineer-in-Charge.

Material and Labour for roughening surfaces of old concrete surfaces by picking, sweeping cleaning and washing down with water to remove dust etc including taking down tarfelt and 15 mm thick screeding in cement mortar 1:4 finished even and smooth without using extra cement including mixed with water proofing compound as per manufacturer instructions (WPC shall be measured and paid separately) complete all as specified and directed by Engineer-in-Charge.

Material and Labour PCC 1:2:4 type B-0 (using 12.50 mm graded aggregate) cement concrete as a leveling course on roof surfaces and coping complete all as specified and directed by Engineer-in-Charge.

Material and Labour for applying a coat of bituminous primer conforming to IS-3384 @ 1.20 Kg/Sqm on prepared surface of plaster as per manufacturer's instructions, manufactured by the same agency of APP membrane. Providing and laying five layered 4 mm thick APP (Atatic poly propylene) modified polyester reinforced water proofing membrane with minimum weight of 4.60 Kg/Sqm as specified here-in-after. The APP membrane shall be laid using LPG torch-on-application with minimum 100 mm side overlap and 150 mm end overlap. The laying of membrane shall be got done through an authorized applicator of manufacturer of the membrane. The APP membrane shall be taken upto minimum 200 mm on vertical surfaces. The edge of the membrane shall be sealed with sealant. The rain water gutter portion shall be finished with cement mortar 1:4 to provide requisite slope towards rain water pipe outlet complete all as specified and as directed. Notes :- (i) Irrespective of lap the net covered area shall only be measured and paid (ii) The quoted rate shall be deemed to be inclusive of primer for APP membrane and SBR latex complete all as specified and directed by Engineer-in-Charge.

Dismantling cast iron or reinforced concrete drain pipes of dia upto 100 mm jointed in cement mortar fixed to wall of high rise buildings and taking out from trenches as required complete all as specified and directed by Engineer-in-Charge.

Supply and Fixing 100 mm bore Cast iron soil, waste and vent pipes, in any length with or without ears, with cement joints, fixed to walls with MS clamps complete all as specified and directed by Engineer-in-Charge.

Supply and Fixing 75 mm bore Cast iron soil, waste and vent pipes, in any length with or without ears, with cement joints, fixed to walls with MS clamps complete all as specified and directed by Engineer-in-Charge.

Supply and Fixing 50 mm bore Cast iron soil, waste and vent pipes, in any length with or without ears, with cement joints, laid in floors complete all as specified and directed by Engineer-in-Charge.

Fixing only CI pipes 75 to 100 mm bore fixed to wall with MS clamps complete all as specified and directed by Engineer-in-Charge.

Supply and Fixing in repairs CI Bends100 mm bore (any radius), diminishing pieces or tapers ( larger bore measured) complete all as specified and directed by Engineer-in-Charge.

Supply and Fixing in repairs CI Bends 75 mm bore ( any radius), diminishing pieces or tapers ( larger bore measured) complete all as specified and directed by Engineer-in-Charge.

Material and Labour in repairs Cast iron nahani trap with grating including jointing to waste pipe run lead 100 mm complete all as specified and directed by Engineer-in-Charge.

Material and Labour for point wiring with FRLS PVC insulated unsheathed multi stranded copper conductor cable of 1.5 sqmm size 1100 volts grade drawn through and including non metalic rigid PVC casing and caping not less than 25mm width with all accessories fixed on wall including FRLS PVC insulated, unsheathed multistranded copper conductor cable of size 1.5 sqmm as earth continuty conductor connecting to common earth dolly and PVC moulded box ISI marked for having the switches, switch sockets regulator etc complete all as specified and directed by Engineer-in-Charge for following:-

One light point controlled by one switch

One Fan/bell point controlled by one 5A switch

One 5 Amps switch socket combination on independent board

One 5A flush type switch socket point on same board board

Material and Labour for point wiring with FRLS PVC insulated unsheathed multi stranded copper conductor cable of 2.5 sqmm size 1100 volts grade drawn through and including non metalic rigid PVC casing and caping not less than 25mm width with all accessories fixed on wall including FRLS PVC insulated, unsheathed multistranded copper conductor cable of size 2.5 sqmm as earth continuty conductor connecting to common earth dolly and PVC moulded box ISI marked for having the switches, switch sockets regulator etc complete all as specified and directed by Engineer-in-Charge for following:-

One 5pin, 15 Amps switch socket combination on ind board

Supply, laying and testing cable XLPE Insulated ,screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 16 sqmm 4 core complete all as specified and directed by Engineer-in-Charge

Material and Labour for submain wiring with 2 runs of 4 sqmm and 1 run of 4 sqmm FRLS PVC insulated unsheathed multistranded copper conductor cable with proper colour coding drawn through and including non metalic PVC casing & caping not less than 25mm width ISI marked with all accessories like PVC elbow, PVC Tee etc fixed on wall complete including connecting up complete all as specified and directed by Engineer-in-Charge

Supply and Fixing LED recess mounted type fitting 36W 2'x2' CRCA LED Slim panel with recess mounting, powder coated white CRCA full glow LED panel including control gear and lamp complete all as specified and directed by Engineer-in-Charge

Supply and Fixing in repair 20 Watt 4 FT LED tube light fitting integrated Batten T5: Nakshatra series indooor light decorative alluminiumextruded T5 LED Batten-integrated type complete all as specified and directed by Engineer-in-Charge. Make- C & S CAT PART NO LTTB4F20WLED/W or as approved by GE

Supply and Fixing in repair 10 Watt 2FT LED tube light fitting integrated Batten T5: Nakshatra series indooor light decorative alluminiumextruded T5 LED Batten-integrated type complete all as specified and directed by Engineer-in-Charge. Make- C & S CAT PART NO LTTB2F10WLED/W or as approved by GE

Supply and fix switch piano, modular type 1 way 6 Amps 1 module 240 volts flush type complete all as specified and directed by Engineer-in-Charge

Supply and fix switch piano, modular type 1 way 16 Amps 1 module 240 volts flush type complete all as specified and directed by Engineer-in-Charge

Supply and fix modular socket 6 Amps 2/3 pin 240 volts Ac combined 2 module all as specified and directed by Engr-in-Charge.

Supply and fix modular socket 16 Amps 2/3 pin 240 volts Ac combined 2 module complete all as specified and directed by Engineer-in-Charge

Supply and fix FAN REGULATOR , modular type 1 way 120W 2 module 240 volts flush type complete all as specified and directed by Engineer-in-Charge

Supply and fix ceiling rose surface bakelite three terminal of size 60x50 mm,240 Volts AC complete all as specified and directed by Engineer-in-Charge

Supply and Fixing steel sheet enclosure double door type IP54 IK09 protection DB VTPN 8 way, 440 volts AC factory made, suitable for housing MCB TPN along with 200 Amps copper bus bar complete all as specified and directed by Engineer-in-Charge

Supply and Fixing in repair Distribution Board double door, prewired type, made out of CRCA mild steel sheet surface with insulated material like polyester or with epoxy powder coating and IP 43 & IK 09 protection surface mounting SPN 8 way, 240 volts with bus bar rating 200 Amps, dust and vermin proof suitable for incorporation of MCB’s and isolators etc complete all as directed. Make -Legrand cat No 507610 or equivalent (Note : The cost of removing old wooden box and making good of surface i.e. brick work, plastering etc is included in quated rate) complete all as specified and directed by Engineer-in-Charge

Supply and Fixing metal boby exhaust fan 380 mm sweep 230 volt 50 HZ AC, having air delivery not less than 1400 rpm supply single phase all as per site requirement incl metallic louver duly fixed on wall and all connected accessories incl taking down old fan and submitting to MES store complete all as specified and directed by Engineer-in-Charge

Supply and fix MCCB 4pole 100A, 16kA

MCB SP 6 - 32 Amps, 10 KA Rupturing capacity

MCB SP 40-63 Amps, 10 KA Rupturing capacity

MCB SPN 40-63 Amps, 10 KA Rupturing capacity

Supply , fixing, testing in repairs of JEF ECO SAFE Maintenance Free Grounding Solution set comprising of High tensile low carbon steel rod of 3 Mts length & 25 mm dia with 250 micron ( avera Schneider ) molecularly bonded copper on the outer surface to confirm with requirements of UL467 along with Back-fill compound strictly be a Carbon based conductive concrete type which has a resistivity of less than 0.12 Ohm Mtr as per Clause 14.5D of IEEE : 80 standard. Back-fill compound should be electronically conductive ( Like in metals ) and should not depend on moisture for conduction. JEF Powerfill Loresco compound shall be supplied in 50 Pound Bag. ( 1 Bag of 50 Pounds required per earthing set). Back-fill comound should be environment friendly, should solidify when mixed with water and set like concrete and should not leach / diffuse into the ground. A suitable earth terminaton clamp should also be supplied along with the set alongwith earth pit weatherproof incl complete all as specified and directed by Engineer-in-Charge. Note : Back-fill compund shall not be mixed with any soil while pouring in the bore hole.

Material and Labour for 4mm GI wire earth continuity conductor or main earthing lead fixed to wall or buried in ground and fixed to panel/transformer alongwith 20mm GI pipe light grade for protection complete all as specified and directed by Engineer-in-Charge

Supply and fix sheet metal enclosure with 2 pin and earth plug and socket complete with single pole MCB of 20 Amps complete all as specified and directed by Engineer-in-Charge.

Supply and Fixing heavy duty metallic body pedastal fan 900 mm sweep 240 volt 50 HZ AC, as per site requirement and all connected accessories and civil work.incl taking down and submitting to MES store complete all as specified and directed by Engineer-in-Charge

jalandhara construction

Satyanarayan Trading Co.