SPECIAL REPAIR TO 48 X WC , 52 X DOOR , MANHOLE AND TILING

Amount

Dismantling of Asbestos cement (corrugated, semicorrugated, etc.) sheets in roof coverings complete all as directed.

Demolition of cement concrete (un reinforced) in ground floors and pavings n exc 15 cm thickness (below or above ground level) complete all as directed.

Taking down chowkhats or frames with shutters (without taking off shutters from the frames) n exc. 1.5 sqm each and removing to store complete all as directed.

Taking down cement or cement lime plaster on brick or stone walls, etc. including raking out joints, hacking for key, scrubbing down with water complete all as directed.

Dismantling floor, hearth or wall glazed tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as directed.

Pre- painted galvalume aluminum zinc AZ 150 coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified.

Pre-painted galvalume aluminum zinc AZ 150 coating GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed.

2mm thick Fibre glass reinforced translucent corrugated sheeting with two corrugations side lap fixed with coach screw and washer in roof, wall etc complete all as directed.

Rolled sections as in main and cross beams, hip and jack rafters; purlins where connected to common rafters and running rails and guides for sliding doors; fixed with angle cleats or other connecting plates conforming to Fe 410-W complete all as directed.

Mild steel work in hand rails, wind ties, posts and struts in fencing screwed or welded to shape as directed, including all necessary drilling, bolting or riveting etc., and similar work confirming to Fe 290 Gde E-165 complete all as directed.

15 mm thick screed bed or bedding layer of mortar in CM 1:6 for laying floor finishes complete all as directed.

40 mm thick cement concrete 1:2:4 type B1 (20 mm graded aggregate) finished even and fair to receive floor finishes complete all as directed.

Non skid ceramic coloured tiles 7 to 8mm thick (square /Rectagular) area of each tile exceeding 0.11 sqm and not exceeding 0.18sqm. in floor etc set and jointed in neat cement slurry and pointed in coloured cement to match for colour tiles complete as specified.

M&L for Glazed ceramic coloured tiles in vertical surface 350 x 250 x 7mm/ 450 x 350 x 7mm thick set and jointed in neat cement slurry and pointed in coloured cement to match complete all as directed.

10 mm thick rendering in CM 1:4 on fair faces of brick work or concrete surfaces of walls for backing coat to tiles and finished even & fair complete all as directed.

15 mm thick rendering in CM 1:4 on fair faces of brick work or concrete surfaces of walls and finished even & fair complete all as directed.

15 mm thick rendering in CM 1:6 on fair faces of stone work finished even and smooth without using extra cement complete all as specified and directed.

Applying three coats of white wash after preparation of new plaster surface of wall complete all as specified and directed.

Applying three coats of white wash after preparation of old plaster surface of wall complete all as specified and directed.

Applying two coats of cement base paint over a coat of primer after preparation of new plaster surface of wall complete all as specified and directed.

Applying two coats of cement base paint after preparation of old plaster surface of wall complete all as specified and directed.

Surfaces of any description, over 10cm in width or girth,not otherwise described new steel surfaces and apply two coat of synthetic enamel paint over a coat of primer complete all as directed.

Cutting holes in one stone wall built in cement mortar for inserting holdfasts and making good dismantled portion in cement mortar 1:3 or cement concrete 1:2:4 Type B-1 as required and directed.

For Providing precast cement concrete1:2:4 type B0(12.50mm graded aggregate) louvres and jallies, 25mm thick (measured solid), including all mould- ings but excluding frame and set in CM 1:6 complete all as directed.

Band straps, supports clamps, hold fasts etc conforming to Fe-410-0 or Fe-310-0 complete all as directed.

100 mm MS but hinges medium weight, cold rolled complete all as directed.

150 mm Aluminium anodised, barrel tower bolts of extruded section and fixed complete all as specified and directed.

150 mm long Extruded aluminium alloy handles, fabricated type, anodised complete all as directed.

Stainless steel wire cloth.0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete all as directed.

2nd Class Hardwood Plain fillets. square, rectangular or triangular insection, clean sawn, securedwith nails or brads sectional area exc 6 sqcm and n exc 13 sqcm complete all as specified and directed.

Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification & drawing shown in SSR 2010 Part -II complete all as directed.

Solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, complete all as specified and directed.

10 litres capacity PVC low level flushing cistern including provision of 15 mm dia PVC connection and PVC flushing pipe of dia and length as required/ ordered to make the system fully functional and making necessary connection as directed in repairs complete.

S & F Vitreous China WC seat Orrisa pattern size 580 x 440mm, white wth integral foot rests fixed in repairs including PVC 'P' or 'S' trap, lime concrete in sunken floor making connection with flush pipe using new GI flush bend (Floor portion) and making good to floors, matching to existing surfaces complete complete all as directed.

15 mm Bib tap standard of PTMT any colour high pressure screwed for iron pipe and fixed in repairs. (Minimum weight 90 gms) complete all as directed.

15 mm Stop valve of PTMT any colour high pressure screwed for iron pipe and fixed in repairs. (Minimum weight 90 gms) complete all as directed.

20 mm Stop valve of PTMT any colour high pressure screwed for iron pipe and fixed in repairs. (Minimum weight 90 gms) complete all as directed.

Taking up or down 20 mm bore steel tubing and connections complete all as directed.

CPVC pipe outer diameter 20 mm SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors complete all as specified and directed.

110mm PVC (SWR) WC connector with lip ring complete all as specified and directed.

Excavating in trenches, n exc1.5 m wide and n exc 1.5 m indepth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sq m on plan and n exc 1.5 m in depth and getting out in soft soil.

160 mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors complete all as directed.

Concrete bed 1:4:8 type D2 to 160 mm bore drain pipes including packing under,and haunching against the sides of pipes after they are laid and tested complete all as directed.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm complete all as directed.

Removing excavated material n exc. 50m and depositing where directed at a level n exc. 1.5 m above the starting point complete all as directed.

Pre-cast cement concrete block1:3:6 type C1 set in CM 1:6 masonry with solid blocks, exc. 10 cm in width and setting in mortar complete all as specified.

Rendering 15mm thick on fair faces of brick work or concrete surfaces in CM 1:4 finished even and smooth with out using extra cement complete all as directed.

Cement concrete 1:4:8 type D-2 in foundations, filling and mass concrete complete all as directed.

Providing, cement concrete 1:2:4 Type B0(12.50mm graded aggregate)as in copings, kerbs rounded or chamfered on edges. Etc complete all as directed.

Providing precast cement concrete in 1:2:4 type B1 for man hole cover slab , etc. set in cm1:6 complete all as directed.

Mild steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire(annealed) not less than 0.9mm dia or securing with clips

Hardcore of gauge n exc. 63mm, broken aggregate deposited, spread and levelled in layers n exc. 15cm thick, watered and rammed to a true surface.

Providing cement concrete in 1:3:6 type C2 (40mm gradedaggregate) 75mm thick as in plinth protection finished even abd smooth with out using extra cement complete all as directed.

Supply and Fix in repair vitreous china wash hand basin, white, flat back size 500x400mm including brackets, pillar tap 15mm bore chromium plated cast copper alloy with capstan heads, 32mm waste coupling brass chromium plated suitable for wash hand basins with long screwed shanks and fly nuts & 32mm PVC waste pipe and 15mm PVC connection pipe, 450mm long complete all as spcified and directed.

Vitreous China urinal bowl type size of 430x370x340mm white with grating and union of discharge pipe (back or corner wall type) complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2 securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement flush pipe grating and union for discharge pipe and 32mm dia PVC wase pipe complete all as spcified and directed.

Rounding to edges of stone slab one edge, such as in steps, cooking platform and other similar situations complete all as directed.

Cudappa stone slab 20-25mm thick work (table rubbed and polished) in steps, jambs, pillars, window cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite complete all as directed.

Taking down copper/ aluminium point wiring (light, fan, socket or power) complete, including fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets, light fittings, fans etc and making good distrubed surfaces of wall, floors, etc complete all as directed.

Point wiring controlled by one 5 Amps switch one way with1.5 Sqmm (Nominal Area) PVC insulated unsheathed 1100 Volts Grade Stranded Copper Conductor Cable (Red Colour Cable for Phase and Black Colour Cable for Neutral), laid in and including PVC Casing and Capping with Accessories (size of Casing and Capping as required at Site) including 1.50 Sqmm PVC ins-ulated Stranded Copper Conductor Cable (Green Colour) as Earth Continuity Conductor and connected to Common Earth Dolly or as directed and MS terminal box with 3mm thick masonite laminated sheet top cover fixed on Wall for one light point controlled by one switch complete all as specified and as directed.

Switch piano, flush button single pole, 5 Amps one way complete all as directed.

Ceiling rose surface bakelite 65x50mm three terminals including supply and fix PVC square blocks complete all as directed.

LED light fitting single tube 20 Watts, 240 V surface and surface and wall mounted led batten, extruded aluminium housing provided for efficient heat dissipation with polycarbonate diffuser & integrated electronic driver with all accessories internally pre-wired and including connecting up with twine core twisted flexible copper contactor cable with 1.5M long suitable size all as specified and directed. Model No : ENDURALINEARNEOBS20WLED865SPCWH Make Havells or equivelent make phillips/Baja/CG.

Street light fittings 1x 15 Watt LED New generation energy saving and environmental friendly long life LED street light made up of pressure die cast aluminium housing with high power LED as lighting source and lens embedded PC cover having TOP Opening seperate driver compartment with IP65 protection and impact resistance of IK07 and including connection up with twine core twisted flexible copper conductor cable with 1.5 M long suitable size all as specified and directed. Cat Part No : ENDURAPEARLSL15WLED757SASYTOPC Make Havells or equivelent make of bajaj/phillips/CG

Steet light bracket made out of 25 mm bore GI Light grade 1.50 M long to required shape as in bracket for steet light fittings fixed with two pair of MS flate iron clamp of size 50mm X 6 mm thickness of required shape with nuts, bolts and washers suitable for steel tubular pole including painting of mild steel flate iron surface with two coates of synthetic enamel paint over a coat of red oxide primer complete including taking down unserviceable one all as specified and directed.

S&F Sheet metal enclosure (ISI marked) distribution board SPN 2 way, 230 V for housing MCB and fixed flush in wall surface, and tested on completion complete including taking down unserviceable one all as directed.

S&F MCB Single pole and neutral 240 Volt20 to 40 Amp capacity complete all as specified and directed.

Exhaust fan AC single phase 230 volts, heavy duty of size 300mm sweep, 1400 RPM, metal body with bird free louver shutter, providing holes including grouting nut bolts nad including 3 core flexible copper conductor cable of size 24/0.20 sqmm connecting up from ceiling rose to exhaust fan terminal complete all as directed. Make : Havells/ Crompton/ Usha/ Orient/ Bajaj

Earthing complete with galvanized steel earth plate electrode 60 cm x 60 cm x 6mm thick buried directly in ground vertically to a depth not less than 2.25 mtr below ground level with top edge of earth plate at a depth not less than 1.5 mtr connected to galvanized earth lead wire 4 mm dia as earth lead up to 7.5 mtr long by means of nuts, bolts, thimbles, check nuts and washers etc made of galvanized iron connected to earthing test point all as shown in electrical plate No 3 of SSR Part-I 2010 and as specified or indicated and testing on completion including earth work and excavation in any type of soil PCC (1:3:6) type C1 chamber, pre cost slab 40mm thick in cement concrete (1:2:4) type B1 with 8 mm dia MS bars reinforced at 10 cm centre to centre both ways including funnel with watering pipe wire mesh and lugs, including testing and dismantling of old earthing complete all as directed.

SHANTA DURGA TRADERS