ADDN / ALTN AND SPECIAL REPAIR TO BLDG NO T-106 NEAR PANIPAT GATE AND ADDN / ALTN AND SPECIAL REPAIRS TO SECURITY WALL NEAR BSO YARD UNDER GE HADDO, PORT BLAIR

Amount

Dismantling plain or corrugated steel sheeting, any gauge, thickness, including Nainital or similar pattern roof coverings etc., complete all as specified and as directed.

S&F pre-painted zinc coated aluminum sheet (Galvalume) GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and as directed. NOTES: The self tapping screw shall be of adequate length to drive into complete thickness of purlin/rafter etc., and shall be fixed using neoprene and EPDM washers. Penetration and laps in sheet shall be sealed by using proper sealant profile. HDPE fillers shall be provided wherever required to close voids between sheets, sheet & fasteners etc., as per SSR Part-I 2009 complete.

S&F pre-painted zinc coated aluminum sheet (Galvalume) GI based plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall/valley gutters, fixed with self tapping screws including scaffolding for a height upto 12.0 metres complete all as specified and as directed. NOTES: The self tapping screw shall be of adequate length to drive into complete thickness of purlin/rafter etc., and shall be fixed using neoprene and EPDM washers. Penetration and laps in sheet shall be sealed by using proper sealant profile. HDPE fillers shall be provided wherever required to close voids between sheets, sheet & fasteners etc., as per SSR Part-I 2009 complete.

S&F in repairs plain aluminium flat section not less than 0.68 Kg per RM as in wind tie and for verticle and horizontal support fixed with aluminium self tapping screws etc complete all as specified and as directed

Dismantling of ceiling boarding including grid of any description, fixed in any position with nails complete all as specified.

M&L for seamless gypsum board false ceiling 12 mm thick including for any sunk or raised moulding with 25mm long self drilling/tapping screws having Philips head with joining compound and 48 mm wide fibre tape to provide seam less finish and including GI frame work of seamless ceiling comprising of GI perimeter channel 0.55 mm thick with two unequal flange of 20mm and 30 mm, web of 27 mm, fixed to surrounding wall using nylon sleeves and screws at 450 mm c/c / intermediate channel 0.9 mm thick having two equal flanges of 15 mm suspended from soffit at approx 900 mm c/c with GI cleats and steel expansion fasteners with and including ceiling section (not exceeding 1.2 m length) of 0.55 mm thick having kurled web of 50 mm and flange of 26 mm each with lips of 10.5 mm fixed to the intermediate channel with connecting across the intermediate channel at 457 mm c/c including hangers 6 mm dia GI adjusting level fixed to roof slabs by means of ceiling cleats made out of GI flat 40x3 mm size, 60 mm long & expansion hold fasteners 12.5 mm dia, 40 mm long and finally applying two coats of oil bound distemper with roller finish over a coat of primer complete all as specified and as directed.

Dismantling of floor hearth or wall tiling including cement mortar bedding (but not backing) removing rubbish off the premises all as specified and directed.

M&L for vitrified ceramic coloured tiles (of approved light shade) of size 600 x 600mm, 9 to 10mm thick in floor, set & jointed in neat cement slurry including a layer of screed bed 15mm thick 1:4 and pointed in coloured cement to match the shade of tiles over cement screed bed all as specified and directed.

All as per item No. 08 but on vertical surfaces such as skirting, dados and riser etc including a layer of screed bed 10mm thick 1:3 all as specified and as directed.

Surface excavation not exceeding 30cm deep and averaging 15cm deep and getting out in hard/ dense soil complete all as specified and as directed.

M&L for hardcore of gauge not exceeding 63mm deposited spread and levelled in layers not exceeding 15cm thick watered and rammed to a true surface of broken stone or boulders complete all as specified and directed.

M&L for 100mm thick PCC 1:4:8 type D2 (Using 40mm graded stone aggregate) as in sub base complete all as specified and directed

M&L for 100mm thick PCC (1:2:4) type B1 (using 20mm graded stone aggregate) as in levelling course, sub base of floorings and pavings complete all as specified and as directed.

M&L for chequered cement concrete tiles 30cm x 30cm x 25mm thick, made of grey cement and pigments, machine pressed as in flooring, set, jointed and pointed in neat cement slurry laid over and including 20mm thick screed bed in CM (1:4) complete all as specified and as directed.

Dismantling of wrought iron or mild steel work and structural steel work of any description ot otherwise provided for complete all as specified and as directed.

M&L for mild steel roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (beam, tee, angle, channel or flat sections) including distance pieces, cleats etc., conforming to Fe-410-W (Gde E-250) Quality 'A' complete all as specified and as directed.

S&F for mild steel rolled sections as in main and cross beams, hip and jack rafters, purlins where connected to common rafters and running rails and guides for sliding doors, fixed with angle cleats or other connecting plates etc., using structural steel conforming to Fe-410-W (Grade E-250) Quality 'A' complete all as specified and as directed.

M&L for preparation of new steel and iron surfaces of any description, not otherwise described, over 10cm in width or girth and applying two coats of synthetic enamel paint of first quality over a coat of red oxide zinc chrome primer complete all as specified and as directed.

M&L for pre-cast cement concrete block masonry with solid blocks made up of (1:3:6) type C1 (using 20mm graded stone aggregate), masonry exceeding 10cm in width and setting in cement mortar (1:6) complete all as specified and directed.

M&L providing precast cement concrete solid building blocks PCC 1:3:6 type C1 (using 20 mm graded stone aggregate) or slabs 10cm thick (with plain or interlocking joints as directed) setting in cement mortar 1:4 in walls complete all as specified

Demolition of cement concrete (unreinforced) of any description as in padding concrete (other than ground floors) complete all as specified and as directed.

Demolition of PCC block masonry, built in cement mortar or cement lime mortar complete all as specified and as directed.

Taking down cement plaster of any description on brick or stone walls etc., including raking out joints, hacking for key, scrubbing down with water etc., and removal of debris to outside MD land complete all as specified and as directed.

M&L for rendering 15mm thick in CM (1:4) on fair faces of brick work or concrete surfaces including mixing of liquid water proofing compound @ 200ml per 50kg cement bag, finished even and smooth without using extra cement complete all as specified and as directed. NOTE : Water proofing compound shall be measured and paid separately.

M&L for rendering 10mm thick in CM (1:6) on fair faces of brick work or concrete, surfaces finished even and smooth without using extra cement complete all as specified and as directed.

M&L for preparation of newly plastered wall surfaces and applying two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm complete all as specified and as directed

M&L for preparation of newly plastered surfaces of walls of any description and applying two coats of distemper oil emulsion over a coat of alkali resistant primer complete all as specified and as directed.

S&F for mild steel framed work such as grills, gratings, etc., with ends of bars shouldered and/or riveted, or forged into spikes, framed guard bars, barred iron doors, ladders, framed balusters, walk ways, railings, framework of water tanks and similar work conforming to Fe-290 Grade E-165 complete all as specified and as directed.

M & L for Cement concrete Type C2 1:3:6 (40 mm graded aggregate) in surface channels and drains etc. complete all as specified and directed.

Extra for forming fair finished drain or channel 30 cm inner girth in cement concrete, using ex- tra cement, including forms, moulds, mi- tred/stopped ends etc., complete all as specified and directed.

Taking down Chowkats exc 1.5 Sqm but n. exc 4 Sqm each with shutters (Without taking off shutters from the frame) complete all as specified and directed

Taking down chowkhats or frames area n. exc 1.50 Sqm each with shutters (without taking off shutters from the frames) complete all as specified and directed

S&F for 2nd class hard wood plain, solid, straight chowkhats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints complete all as specified and directed

S&F for 38mm thick rubber wood panneled shutters (02 panels), with styles of 100mm, bottom and middle rail 100mm, top rail, 150mm and panneled with 18mm rubber wood as specified and directed by Engr-in-Charge.

Supply only sheet glass 5.5mm thick ordinary quality in square exc 0.5 Sqm in each pane complete etc. complete all as specified and directed.

M&L for preparation of new/old wooden surfaces and applying melamine polish through the process of snading with wood sanding paper of size 60 & 80 and applying wood filler mixed with NCD thinner including applying wood putty on shabby/ nailing area and sanding with sand paper of size 120 and applying sealer and walnut colour stainer and sanding with sand paper of size 320 and melamine polishing with spray application and again sanding with 400 sand paper and finally applying silicon of make Waxpol with soft fine cloth for better shining and finishing complete all as specified and directed

M&L for powder coated aluminium partition, window and door/ventilator with frame and shutters fully or partly glazed, sliding/openable/fixed fully glazed and panels fixed with panels inserts 12 mm thick pre-laminated particle board/sheet glass including necessary jointing cleats, glazing clips, rubber beading, neoprene packing, anodised aluminium snap beading, screws, anodized aluminium fittings such as handles, aluminium butt hinges, aluminium tower bolts etc. The size of aluminium section shall be all as specified in relevant IS Code and SSR Part-I complete all as specified and as directed. NOTES: (i) Supply only floor spring, glass, Imax hinges, SS friction hinges, particle board, aluminium fly proof mesh will be measured and paid separately under relevant items of this BOQ. (ii) Weight of aluminium section only shall be accounted for the purpose of payment. However unit rate quoted shall be deemed to include for cost of rubber beading, neoprene packing, fittings such as handles, butt hinges, tower bolts, rollers for sliding windows, locking arrangement and fixing only of panel inserts of glass/ particle board/aluminium fly proof mesh etc. (iii) Weight of aluminium handle, butt hinges, tower bolts shall not be accounted for payment purpose.

S&F Door closer hydraulically regulated aluminium (die cast) body, designation No 3, universal type, suitable for door shutters of 851 to 1000 mm in width and of weight between 61 to 80 Kg complete all as specified

S&F for brass handles, size 150mm cast type, polished bright complete all as specified and as directed.

S&F 100mm size butt hinges, stainless steel hinge pin, anodised, and fixed type C-21 complete all as specified and as directed.

S&F 150mm brass barrel tower bolts, with cast or sheet barrel and rolled or cast bolts of extruded section complete all as specified and directed.

Supply and fix 300 mm long brass sliding door bolt with hasp and staple (bolt type) and fixing bolts with rolled or drawn brass bolts and fixed complete all as specified and directed.

Supply and fixing of UPVC/ fibre false ceiling of panel (not less than 1mm thickness) sizes of 340mm x 2700mm/ 300mm x 2500mm, durable and resistant to moisture, water and borer-fungus-termite attack. Panels to be installed with GI/ Aluminium sections of suitable gauge & size according to site conditions. Panels fixed using with suitable trims for edge profiles and for connecting profiles. Panels must be maintenance free, rust proof and are 100% water proof complete all as specified and sample kept in the office of the Engr-in-Charge. Note:- (i) Colour and pattern of false ceiling boards to be approved by GE. (ii) GI frame work of false ceiling will be measured and paid separately.

S&F GI frame work of seamless ceiling comprising of GI perimeter channel 0.55mm thick with two unequal flange of 20 and 30mm and web of 27 mm fixed to surrounding wall using nylon sleeves and screws at 450mm c/c intermediate channel 0.9mm thick having two equal flanges of 15mm each and web of 45mm suspended from soffit at approx 900mm c/c with GI cleats and steel expansion fasteners with and including ceiling section (not exc 1.2m length) of 0.55mm thick having kurled web of 50mm and flanged of 26mm each with lips of 10.5mm fixed to the intermediate channel with connecting across the intermediate channel at 457mm c/c including hangers 6mm dia GI adjusting level fixed to roof slabs by makes of ceiling cleats made out of GI flat 40 x 3mm size 60mm long and expansion hold fasteners 12.5mm dia 40mm long complete all as specified and directed.

S & F aluminium composite panel sheet of 3.0mm thick with skin thickness of 0.25mm of aluminium on both sides, sandwiched by 2.5mm polythelene core with PVDF coating of 30.0 micron with expansion fastener, having panels not exc 1200 x 1200mm with necessary silicon fitting,in aproved pattern as in column, beam, wall etc. complete all as specified and as directed. Note:- Necessary MS scaffolding required for work shall be deemed to be included in the quoted rate.

M & L for designer cornices all round the corners of seamless false ceiling allas specified and directed.

Dismantling wood boarding, panels, beams or any description, fixed any position with nails as in eves & barge boards.

M &L for boarding (eaves / barge board) with 19mm thick plywood (BWR) fixed with screws on flat iron supports including applying two coats of synthetic enamel paint over a coat of pink primer.

M &L for providing and fixing stainless steel (Grade 304) railing made of hollow tubes, channels, plates, etc. including welding, grinding, buffing, polishing and making curvature (where ever required) and fitting the same with necessary stainless steel nuts and bolts complete, including fixing the railing with necessary accessories & stainless steel dash fasteners, stainless steel bolts, etc., of required size, on the top of the side of waist slab with suitable arrangement

M & L for applying wall care putty, average 1mm thick on wall surface complete all as specified and directed.

M&L for complete removal of existing treatment on wall and applying two coats of oil bound distemper over a coat of primer complete all as specified and directed

M&L for complete removal of existing treatment on plastered wall surface and applying two or more coats of 100% premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/10 Sqm over and including priming coat of exterior primer applied @ 0.90 litre/10 Sqm complete all as specified and directed

Erection and fixing only of roof trusses (framed), trrussed, purlins, crane gantries, rails and fastenings and heavy bracket framming (Beam,Tee, Angle, Channels or flat sections) including distance pieces, cleats etc conforming to Fe 410-W (Gde-E-250) quality-A complete all as specified and as directed. Note :- Retrieved material from dismantling /demolition to be used.

M&L for preparation of old painted steel surfaces of any description, not otherwise described, over 10cm in width or girth and applying one coat of synthetic enamel paint of first quality complete all as specified and as directed.

M & L for precast cover slab with 1:2:4 type B1 using 20mm graded stone aggregate incl cost of use and waste of clean sawn wooden form work but excl. cost of reinforcement complete all as specified and directed.

S&F TMT steel bars 10mm dia and over, cut to length, bent to shape required, including cracking bending spirally for hooping for columns/beams, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia complete all as spcified and directed.

S & F 18mm thick rubber wood pelmet box in narrow widths n. exc 15cm each, rebated or flat edged as specified and directed by Engr-in-Charge.

Demolition of stone slabs and tiles of any description or thickness in floors, aprons etc laid bedded and pointed in any mortar complete all as specified and directed

Material and labour for 20 mm thick granite( of any type) (table rubbed and polished) in cooking platforms, steps, cills, pillars and like in CM 1:4 including pointing in white cement 1:2 using marble dust with admixture of pigment to match with shade of granite including 15 mm thick screed bed in CM 1:4, including rounding and polishing of edges complete all as specified and directed.

Material and labour for 20 mm thick granite as in counter slabs of WHB( of any type) work (table rubbed and polished) and like in 15mm thick in CM 1:4, including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite complete all as specified and directed.

Material and labour for 12 mm thick prelaminated particle board, interior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination in cup board shutters all as specified and directed.

Supply and fix solid PVC door frame of size 50 mm x 47 mm made out of 5 mm plain colour PVC sheet reinforced with MS square tube, all as per specification and as directed.

S&F factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of MS tubes for top and bottom rails. MS frame shall be covered with heat moulded prelam PVC 'C' channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and both side prelam PVC sheet for top rail, lock rail and bottom rail on either side as gap insert for top rails, bottom rail, panelling of both side prelam PVC sheet to be fitting in the MS frame welded/sealed to the stiles and rails with suitable PVC sheet beading and joined together with solvent cement in the frame at site as per specification and drawing complete etc. complete all as specified and directed.

S&F for butt hinges 75mm, long stainless steel hinge pin and fixed complete all as specified and directed.

S&F 150mm size extruded aluminium alloy handles, fabricated type, anodised complete all as specified and directed.

S&F 150mm aluminium, anodised, barrel tower bolts of extruded section complete all as specified and directed.

S&F sliding door bolt, 300mm long, aluminium alloy, anodised, with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy complete all as specified and as directed.

Taking up or down 15mm bore steel tubing and connections including cleaning for re-fixing or removal to store complete all as specified and directed

Cutting chases, pinning in making good to facings in wall where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc and cutting chases for concealed water tubing or concealed conduit wiring etc and making good, cutting not exc 10 cm girth complete etc. complete all as specified and directed.

S&F 20mm outer dia CPVC pipes SDR 13.5 and plain CPVC SDR 11 fittings on walls/ceiling or laying in floors complete all as specified

S&F of 25mm outer dia CPVC pipes SDR 13.5 and plain CPVC SDR 11 fittings on walls/ceiling or laying in floors complete all as specified

S&F in repair PVC valveless syphonic action type flushing cistern 10 ltr capacity white with intel ball valve float flush pipe and handled including brackets complete all as specified.

S&F for fixed in repairs white vitreous china wash down water closet pan (pedestal pattern) with PVC seat cover with mild steel chromium plated or aluminised hinging device including connection to drown pipes and flushing pipe complete all as specified

S&F in repair vitreous china wash hand basin of size 550x400mm including brackets, 15mm dia CP pillar cock, 15mm dia PVC connection, 32 mm CP waste coupling, chain and plug, waste fittings all necessary inlet and out let connections complete all as specified

M & L in repairs for 32mm dia waste coupling fittings, brass, chromium plated for basin etc with long screwed shanks and fly nut and bedded in red lead cement other. complete all as specified

M & L in repairs for 40mm dia waste coupling fittings, brass, chromium plated for kitchen sink etc with long screwed shanks and fly nut and bedded in red lead cement other. complete all as specified.

S & F in repair PVC connection 15mm size with PTMT nut of length 600mm long complete all as specified.

S & F in repair for plastic water closet seat, white, closet pattern with flat bottom, and cover and mild steel chromium plated/ PVC or aluminiumn hinging device complete all as specified and as directed.

S & F in repairs 32mm dia PVC (flexible) waste pipe for wash hand basin complete all as specified and as directed.

S & F in repairs 38mm dia PVC (flexible) waste pipe for kitchen sink complete all as specified and as directed.

S&F in repairs bib tap, brass, 15mm dia, cast copper alloy, chromium plated, with crutch or butterfly handle, screwed down, screwed for iron pipe or brass ferrule complete all as specified and as directed.

Supply and fix in repair 15 mm bore Pillar taps, cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered `Hot' or `Cold' with long screwed shanks and fly-nuts, screwed for iron pipe and fixed all as specified and directed.

Supply and fix in repairs, CP angle cock 15mm dia. fancy type cast copper alloy of Make-Jaquar Cat. No. CON-053KN complete all as specified and as directed.

Supply and fix in repairs, CP bib cock 15mm dia with crutch handle as approved fancy type long body Make - Jaquar CON-107KN complete all as specified and as directed.

Supply and fix in repairs Toilet paper holder Make :Jaquar Code ACN-1153N complete all as specified and as directed.

Supply and fix in repairs CP Single Towel Rail 600 mm long Make : Jaquar AQN 7711 complete all as specified and as directed.

Supply and fix in repairs CP brass 15mm health faucets with 1 mtr tube and hook with metallic expandable tube 15mm complete set Make : Zim Cat No. 1624A complete all as specified and as directed.

Supply and fix in repairs, stainless steel grating cover 100mm dia fixed with white cement all as specified and directed.

Supply and fix in repairs shower rose chromium plated with or without swivel joints, 125 mm size, including fixing to steel pipe or union complete all as specified and directed.

M & L for applying wall care putty, average 1mm thick on ceiling surface complete all as specified and directed.

Demolition of reinforced cement concrete (Reinforcement cut as required to facilitate demolition) of any description and in any position not otherwise specifically provided for all as specified and as directed.

Excavation in trenches n. exc 1.5m wide and n. exc 1.5m in depth in hard/dense soil for foundation, etc or for shafts, wells, cesspits, manholes, pierholes, etc n. exc 10 Sqm on plan and getting out complete all as specified and directed

Rough Excavation n. exc 1.5m deep and getting out in hard/dense soil including clearing away all grass vegetation, saplings, shrubs, brushwood, undergrowth, roots and trees not exceeding 30cm girth (measured one metre above ground level) complete all as specified and directed

Returning, filling in hard/dense soil including spreading, levelling, watering and well ramming in layers not exceeding 25 cm thick complete all as specified and as directed.

Removing excavated material (Soils) to a distance n. exc 50m and depositing where directed at a level n. exc 1.5m above the starting point complete all as specified and directed

Removing building materials etc. to a distance exc 200m but n.exc 500m in low lying MoD area or under, beyond the lead included in the rates, including loading, unloading and stacking at the destination complete all as specified and directed

M&L for PCC (1:4:8) type D2 (using 40mm graded stone aggregate) as in foundation filling and mass concrete complete all as specified and as directed.

M&L for reinforced cement concrete (Design mix) M-30 (using 20mm graded stone aggregate) as in foundations, including rafts, footings, foundation beams, plinth beams, bases for columns etc., basement slabs, under-reamed piles and mass concrete complete all as specified and as directed.

M & L for reinforced cement concrete desin mix M-30 ( using 20mm graded crushed stone aggregate) in coloumns,pillars, piers, posts and struts complete all as specified and as directed.

M & L for reinforced cement concrete desin mix M-30 ( using 20mm graded crushed stone aggregate) in beams, cantilevers, bressumers,lintels over 1.5m span complete all as specified and as directed.

M&L for use and waste of formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams and similar work vertical or to batter for rough finished surfaces of concrete flat complete all as specified and as directed.

M&L for formwork for rough finished surface of square, rectangular, or triangular surface to side of pillar, posts, struts, piers, column and stanchions complete all as specified and directed.

M&L for formwork to side and soffits of floor or room beam, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs etc also splays between floors and beams etc in rough finished flat surface complete all as specified and directed.

M&L for Mild steel TMT bars 6mm to 8mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns/beams, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and as directed.

M&L for pre-cast cement concrete block masonry with solid blocks made up of (1:3:6) type C1 (using 20mm graded stone aggregate), masonry exceeding 10cm in width and setting in cement mortar (1:4) complete all as specified and directed.

Supply only liquid water proofing compound complete all as specified and directed.

Supply, spread, loose filling 40mm graded Coarse stone aggregate in layers of 100mm thick complete all as specified and directed.

S&F PVC (SWR) pipe 110mm bore, single socketed, in any length including bends, socket etc with rubber ring joints and jointed with approved adhesive laid in trenches or in floors complete all as specified and directed

S&F MS hand rails, half round or other steel section of core for wooden hand rail straight portion, drilled and countersunk for balusters running bars, for doors, balusters, nosing to steps including embeding in concrete and screwing etc wind ties for roof including securing bolts posts and struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire, etc., flat iron fillets (for securing wire mesh etc) including all necessary drilling, bolting or riveting, etc., and similar work confirming to Fe-290 Gde E-165 complete all as specified and directed.

S&F Galvanised. 2 strand, steel barbed wire 2.24mm dia barbed with 2mm dia barbs at 75mm spacings and straining and fixing to any type of standard rails straining bolts, including, securing or tying at crossings with and provision of galvanised mild steel wire, staples or steel pins, etc. as directed (each line wire to be measured)

M&L Non - skid coloured Ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over 15mm thick screed bed in CM (1:4) complete all as specified.

M&L for Glazed ceramic tiles in vertical surfaces such as skirtings, wall, dados and risers to steps etc.surface 350x 250x 7 mm/ 450X 350X 7mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match over 10mm thick rendering in CM 1:3 complete all as specified and directed.

M&L for reinforced precast cement concrete 1:2:4 type B1 (using 20mm graded stone aggregate) as in landings, drain cover, cover slabs (for manholes etc), shelves and similar articles with plain faces including necessary form work, set in CM 1:4 complete all as specified and directed (Note : Reinforcement shall be measured and paid for separately)

Taking down carefully copper/aluminium point wiring for light, fan, socket or power point etc complete with all fittings and fixtures such as switch piano, ceiling rose switch, socket, Pendents etc including making good surface of wall, ceiling etc complete all as specified and directed.

Taking down old aluminium sub main wiring of any size.Complete all as specified and directed.

Taking down fuse Unit/ DBs 415 Volt/ 230 Volt Complete all as specified and directed.

Taking down existing light fittings of any type complete all as directed .

M&L for Point wiring complete as specified with 1100 volt grade 1.5 sqmm. (nominal area) single core PVC insulated unsheathed cable multi stranded copper conductor drawn through and including rigid non-metallic PVC concealed conduit of size not less than 20mm dia, with all fittings, concealed in wall/ ceiling/ floor including decorative modular cover plates (inner and outer) suitable for housing modular pattern switches/ sockets/ regulators etc. along with necessary metal boxes flush mounting in the wall duly earthed with same cable as for wiring above but green in colour as continuous earthing wire complete all as specified for the following :- Make of wire :- Polycab/ Gloster/ Anchor/ Havells/ Finolex/ and Make of PVC Casing & Caping /Conduit : Modi/ Precision/ Supreme/ Finolex/ Polycab.

ONE LIGHT/FAN point controlled by one, one way 6 Amps switch.

Point wiring for 3 pin switch socket outlet, 6 Amps on independent board

Point wiring for 3 pin switch socket outlet, 6 Amps on same board

M&L for Point wiring complete with 4 Sqmm (nominal area) single core, PVC insulated unsheathed, FRLS cable, 1100 volts grade, multistranded copper conductor (with colour coding of Red/Blue/Yellow for phase and Black for neutral), drawn through and including rigid non metallic PVC concealed conduit of suitable size not less than 20mm and accessories concealed in walls/ceilings etc., including provision of PVC insulated 4 Sqmm FRLS cable with copper conductor green in colour for earth continuity and connected to common earth dolly and sunk in CI boxes/pressed steel terminal boxes 60mm deep made out of 1.6mm thick MS sheet duly painted with two coats of anti-corrosive paint outside and with two coats of aluminium paint inside and covered with suitable size of modular cover plates for socket outlet etc, all as specified and as directed for ONE 16A SOCKET OUTLET point controlled by one, one way 16 Amps switch on independent board.

S&F modular switch, one way, one module, single pole, 6 Amps, 230 Volts AC complete all as specified and as directed. Make: Roma (Anchor) / Havells/Simens / Legrand

S&F modular switch, one way, one module, single pole, 16 Amps, 230 Volts AC complete all as specified and as directed. Make: Roma (Anchor) / Havells/Simens / Legrand

S&F socket outlet, modular type, 1 way 6 Amps, 3 pin flush type 230 Volts AC circuit complete all as specified and as directed. Make: Roma (Anchor) / Havells/Simens / Legrand

S&F socket outlet 2 in 1, modular type, 3 pin 6/16Amp, flush type, universal all as directed. Make : Anchor/Cona/Legrand

S&F and testing surface tube light fittings LED 20 watts 4 feet including all accessories and fixing arrangements for fixing the light fitting complete all as specified and as directed. Make : Luker Cat Part No : LT510P or equivalent of CG/Philips/Havells

S&F and testing surface tube light fittings 10watts LED 2 feet including all accessories and fixing arrangements for fixing the light fitting complete all as specified and as directed. Make : Luker Cat Part No : LT5M10 or equivalent of CG/Philips/Havells

S&F of LED SLIM panel lighting fixture of 18 Watt recess mounted 220V, 50Hz environmental friendly energy efficient fitting recess mounted round/square in shape (warm white/ white colour as per requirement of site) of light as required at site complete all as specified and directed. Make : Luker Cat Part No : LNPS30 or equivalent of CG/Philips/Havells

S & F 30 Watts LED building security light fittings are made up of pressure die cast housing with toughened glass and high power LED's with secondary optics and IP66 protection including necessary fixing arrangements as per site requirements complete all as specified and as directed. Make :- Luker Model No. LSTE-30 or equivalent of Havells/Philips/CG

Taking down old unsv street light brackets of any size and supply and fixing new GI brackets of GI pipe light grade of size 25mm dia including nuts, bolts and washers for building security light all as specified and directed.

S & F air ventilating fan 250mm sweep single ph, 230 volt PVC body with louvers incl all fixing arrangement complete all as specified and directed Make:- Havells, model No. FHVVEDXOWH10 Venti Air DX or CG, Model No. BRISK AIR NEO or equivalent to Orient / Usha/ Khaitan

Taking down carefully ceiling fan of any make, size from its location, dismantling complete, examine complete parts thoroughly, oiling, greasing all parts and complete overhauling of fan including replacement of small parts such as split pin, nut bolt, screws and assembling back the fan, make fully functional, refixing the fan to its positioning including replacing and providing of twin core copper wire 23/0.0076 through flexible conduit from fan to ceiling rose and painting the fan with same colour of fan complete all as specified.

S&F of ball bearing of ceiling fan No 6201/6202 all as directed.

S&F of ceiling fan shaft suitable for 1200/1400mm sweep ceiling fan all as directed

S&F in repair of fan blade for ceiling 1200mm sweep/1400mm sweep including all accessories complete as directed

M&L for Sub main wiring complete with two runs (1P+1N) of 4.0 Sqmm single core, PVC insulated unsheathed, FRLS cable, 1100 volts grade, multistranded copper conductor (with colour coding of Red/Blue/Yellow for phase and Black for neutral) and one run of 4.0 Sqmm single core, PVC insulated unsheathed, FRLS cable, 1100 volts grade, multistranded copper conductor as earth wire green in colour including lugs, drawn through and including suitable size PVC conduit and conduit accessories concealed in wall/ceiling/roof/ floor complete all as specified and as directed. NOTE: Two runs of 4.0 Sqm copper conductor, One run of 4.0 Sqmm copper conductor as earth wire and one run of PVC conduit shall be measured as one unit length.

S & F DB VTPN sheet metal enclosure double door IP 43 protection, door earth suitable for incoming upto MCCB 160 Amps/200 Amps & outgoing MCB TP / SP. Triple pole and neutral 415 V 4 Way with 200 Amp rated standard bus bar of suitable size plate and common neutral link all enclosed in standard steel sheet flush mounting type factory fabricated complete including taking down old unserv DB of any type /rating and making good to the distrubed surface /walls all as specified and directed. Make : C&S/Indo Asian/Havells/L&T

S&F MCCB, 4 pole, 100 Amps, 50Hz, 25KA rupturing capacity, 415 Volts adjustable type with thermal and magnetic release complete all as specified and as directed. MAKE: C&S/Indo Asian/Havells/L&T

Supply and fix single pole and neutral sheet steel powder coated distribution board for MCBs fitted with bus bar, Neutral link, Earth bar, and Din rail suitable for use on 240 V, 50 Hz supply double door S P & N DB system 08 way fixed concealed on wall all as directed. Make: Standarad / L&T / Havells Note :DB shall be cencealed in wall distrubed area shall be made good with Cement plaster 1:3 surface finished to match the existing surface all as directed.

S&F single pole and neutral sheet steel powder coated distribution board IP-43 protection with door earthing for MCBs fitted with 200 Amps rated bus bar, Neutral link, earth bar and din rail suitable for use on 240V, 50Hz supply double door SP&N DB system 4 ways, including taking down old unserviceable DB of any type / rating and making good to the disturbed surafce / walls complete all as specified and directed. Make : C&S / Indo Asian / Havells / L&T / Legrand

S&F MCB, TPN, 20-32 Amps "C" series, having current rating 10 KA complete all as specified and as directed. MAKE: C&S/ Indo Asian/Havells/L&T

S&F MCB, SPN, "C" series, 40 Amps, having current rating 10 KA complete all as specified and as directed. MAKE: C&S/ Indo Asian/Havells/L&T

S&F MCB, single pole 6 to 32 Amps, "C" series, having current rating 10 KA complete all as specified and as directed. MAKE: C&S/ Indo Asian/Havells/L&T

Supply, laying,testing and commissioning of LT XLPE insulated armoured heavy duty electric aluminium conductor cable 1100 volt grade of cross section 25 sq mm 4 core (laid on floor/Roof/wall in proper saddling all as specified and directed

Supply and laying/fixing in trenches or in cable ducts or clamping on wall or any place DWC HDPE pipe of size 50 mm(OD) x 38mm (ID) along with connected accessories like couplers.bends,end caps etc. for LT cable protection all as specified and directed.

M&L for cutting channels, grooves or rebates not exceeding 15cm girth in PCC block masonry/RCC, trimming surface and making good surfaces to match with existing surfaces complete all as specified and directed.

M&L for earthing complete with GI earth plate electrode of size 600mmx600mmx6.15mm thick buried directly in ground (earth pit not less than 2.25m deep below the normal ground level) with top edge of the earth plate not less than 1.5m below normal ground level connected to 4mm dia GI earth wire as earth lead connected by means of bolts, nuts, washers and check nuts made out of galvanised iron or steel all as shown on electrical plate No. 3 of SSR Part-I connected to common earth dolly including testing on completion complete all as specified and directed. NOTES: (1) The unit rate shall also include for earth work in any type of soil, PCC (1:3:6) type C1 chamber, pre-cast RCC (1:2:4) type B-1 using 20mm graded stone aggregate cover 50mm thick reinforced with TMT bars 8mm dia @ 100mm c/c both ways, funnel with watering pipe 20mm dia GI medium grade, GI protection pipe light grade 40mm dia and wire mesh complete in addition to item No. 1(a) to (e) of preamble (notes) under sub-heading earthing, specified on Sl. Page Nos. 422 & 423 of SSR Part-II. (2) Earthing lead and GI protection pipe beyond 7.5m will be measured and paid separately.

CARTWHEEL CONSTRUCTION

JD Construction

LOOK UP ENTERPRISES

Sree Tirumala Enterprises

M/s Ramesh Lal

M/S VISHAL CONSTRUCTION

SKV Engineering