SPECIAL REPAIR TO BLDG NO P 28 UNIT COOK HOUSE AT 372 COY ASC (SUP) TYPE A

Amount

M&L for water proofing treatment over cleaned roof surface with APP modified bituminous membrane of thickness not less than 3 mm comprising of the following for roof treatment including removing old roof treatment by picking, sweeping clean and washing down with water to remove dust etc and removal of debris from site complete all as specified and directed.:-

M&L for 10 mm screed bed on concrete surfaces in CM (1:3) mixed with water proofing compound @3% by wt of cement finished fair and even complete all as specified and directed. (Note : WPC shall be measured and paid seprately in respective item)

The surface of roof,parpet and gutters drain mouths etc over which water proofing treatment is to be applied shall be cleaned of all foreign matter such as fungus,mass dust etc by wire brushing and dusting. For cast iron drain outlets a groove shall be cut as specified and directed.

Oil based Bitumen primer conforming to IS-3384-1986 @ 0.3 kgs per sqm to be applied on prepared surface till the surface is properly impregnated.

Applying one coat of hot blown grade bitumen 85/25 grade @ 1.20 kg/Sqm

Laying of APP modified polymeric water proofing membrane of weight not less than 3 Kg / sqm composed of 100 micron (+10% ) high density polyethylene sheet ( HMHDPE) as center core, which is sandwiched between high quality polymeric bitumen mix having softening , high heat resistance and cold flexible protected on either side with a thin thermo fusible HMHDPE film with side and laps 75 mm and 100 mm as per manufacture instruction etc.

Applying one coat of hot blown grade bitumen 85/25 grade @ 1.20 kg/Sqm over the membrane

Applying aluminium paint in two coat @ 100 gm/sqm in each coat on finished membrane surfaces complete all as specified and directed at site .

Demolition of cement concrete not exc 15 cm thick below or above ground level as in floor paving etc including removal of demolished material from work site complete all as specified and directed.

M&L for 75 mm thick PCC 1:3:6, type C-1 (using 20mm graded stone aggregates) as in plinth protection finishing cement concrete surfaces even & smooth without using extra cement including forming construction joint of size 10mm x 20mm filled with bitumen and sand motor in ratio 1:3 complete all as specified and directed.

M&L for 25 mm thick cement concrete 1:2:4, type B-0 (using 12.5mm graded stone aggregate) as in floor finishes complete all as specified and directed.

M&L for non-skid coloured ceremic tiles 7 to 8 mm thick (Square/ rectangular) area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm as in floors etc. set & jointed in neat cement slurry and pointed in coloured cement to match coloured tiles laid over and including 15 mm thick screed bed or bedding layer in CM (1:6) including dismantling of floor, hearth or wall tiles / terrazo including cement mortar bedding and rubbish off the premises complete all as specified and directed.

All as per Srl item No.5 above but in dado / skirting etc laid over and including 10 mm thick rendering in CM 1:4

M&L for glazed ceremic tiles of size 600mm x 300mm x 7 mm thick as in vertical surfaces, set & jointed in neat cement slurry and pointed in coloured cement to match coloured tiles laid over and including 10 mm thick rendering in CM (1:4) including dismantling of floor, hearth or wall tiles / terrazo including cement mortar bedding and rubbish off the premises complete all as specified and directed.

M&L for plain cement concrete1:4:8, type D-2 (using 40mm graded stone aggregates) as in mass concrete as in foundation filling, sub base, level course and mass concrete complete all as specified and directed.

M&L for machine pressed precast cement concrete coloured chemically treated interlocking paver block any shape and size conforming to IS-15658-2006 of 60 mm thickness M-35 grade with grey cement and pigment laid over and including 40mm thick uniformly levelled surface of stone dust cushioning complete all as specified and directed.

M&L for brickwork with subclass 'B' bricks, old size straright or curved on plan exc 6m mean radius built in cement mortar 1:6 inclding demolition of brick work and stone/ boulder masonary built in cement mortar and lime mortar complete all as specified and directed.

All as per Srl item No 10 above but except bricks Note:- Serviceable bricks obtained from demolition shall be re-used in this item

M&L for brick work with subclass 'B' bricks as in half brick thick walls built in CM 1:4 inclding demolition of brick work and stone/ boulder masonary built in cement mortar and lime mortar complete all as specified and directed.

M&L for rendering 15 mm thick on other than fair faces of brickwork or concrete surface in cement mortar 1:6 surface finished fair and even complete all as specified and directed.

M&L for rendering 15 mm thick on brick wall or concrete surface in cement mortar 1:6 finished fair and even including taking down cement plaster on brick wall etc including racking out joints hacking for key, scrubbing down with water complete all as specified and directed.

M&L for rendering 20 mm thick on brick wall or concrete surface consisting two layers, under layer of 10mm thick in CM (1:6) & top layer of 10 mm thick in cement mortar 1:4 mixed with water proofing compound, finished even and smooth without using extra cement including taking down cement plaster on brick wall etc including racking out joints hacking for key, scrubbing down with water complete all as specified and directed. (Note:- Water proofing compound shall be measured and paid saperately.)

M&L for rendering 5 mm thick on fair faces of brick work or concrete surfaces in CM (1:3) in ceiling including necessary scaffolding including taking down cement plaster on brick wall etc including racking out joints hacking for key, scrubbing down with water complete all as specified and directed.

M&L for applying three coats of white wash on new plastered surface of ceiling surface including preparation of surface complete all as specified and directed.

M&L for applying two coats of exterior emulsion weather proof paint over one coat of exterior wall primer on newly plastered or unplastered wall surface including preparation of surfaces, complete all as specified and directed. Make : Asian APEX or equivalent make as approved by GE

M&L for complete removal of existing treatment from wall by scrapping etc and applying two coats of exterior emulsion weather proof paint over one coat of exterior wall primer incl. preparation of surfaces of old decorated walls etc, properly making of v shape crakes and filling of all crakes with crakes seal of walls complete all as specified and directed by Engr-in-charge. Make : Asian APEX or equivalent make as approved by GE.

M&L for preparation of newly plastered surfaces on wall and applying two coats of oil emulsion distemper over a coat of wall primer over a coat 2mm thick JK/Birla white wall care putty complete all as specified and directed.

M&L for applying two coat of interior oil emulsion white or tinted over a layer of 2 mm thick JK/birla white wall putty on old decorated or undecorated wall surface including preparation of surfaces by washing rubbing down and stoping of distempered and painted surfaces complete all as specified and directed.

M&L for complete removal of existing treatment from old plastered surfaces of ceiling including preparation of old surfaces and applying two coats of white wash complete all as specified & directed.

M&L for one coat of synthetic enamel paint on old painted wood/wood based surface of any desription over 10cm width or girth incl preparation surfaces such as removing all splashes, drops, dirt and leaving premisesin a clean state complete all as specified and directed

Supply only liquid water proofing compound complete all as specified and directed

M&L cutting grooves in brick wall, 75 mm wide and 65 mm deep and shaping horizontal face of groove with cement mortar 1:1 complete all as specified and directed.

M&L for 18 mm to 20 mm thick granite slab (table rubbed and polished ), machine cut, for floors/ shelves, cooking platforms, window cills etc laid over and including 15mm thick CM 1:4 cement screed and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including cutting and polishing edges to be rounded including dismantling of old exisitng stone or flooring of any description & removing rubbish outside MoD land complete all as specified and directed.

M&L for RCC 1:2:4, type B1 (using 20 mm graded stone aggregates) as in beams, cantilevers, lintels over 1.50Mtr span etc.including necessary formwork including demolition of reinforced cement concrete, (other than ground floors), shelves, chajjas, slabs and similar work carefully and matching to adjoining disturbed surfaces all as directed complete all as specified and directed

M&L for RCC 1:2:4, type B1 (using 20 mm graded stone aggregates) as in slab, shelves etc.including necessary formwork including demolition of reinforced cement concrete, (other than ground floors), shelves, chajjas, slabs and similar work carefully and matching to adjoining disturbed surfaces all as directed complete all as specified and directed

M&L for mild steel TMT bars 6mm to 8mm dia,cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends & binding with & including mild steel wire (annealed) not less than 0.9mmdia or securing with clips complete all as specified and directed.

M&L for mild steel "TMT" bars 10mm dia and over in reinforcement, cut to length, bent to shape required including cranking, bending sprially for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed. .

M&L for TMT bars 5 mm dia and over up to and including 10 mm dia in stirrups, spacers and binders , cut to length, bent to shape required including binding with mild steel wire (annealed) not less than 0.9mm dia complete all as specified and directed

S&F in replacement 1000 ltr capacity of rotational moulded polyethyline water storage tank (Cylindrical vertical with closed top) three layered wall construction hoisted & fixed in position complete all as specified and directed

M&L for cutting chases, pinning in , for concealed water tubing on brick walls, making good to facing where required and pointing in cement mortar 1:3, not exc 10 cm girth complete all as specified and directed.

S&F GI tubing 15 mm bore medium grade with all fittings fixed to walls and ceilings or laid in floors including taking down of GI tubing and connection all as specified and directed.

S&F GI tubing 20 mm bore medium grade with all fittings fixed to walls and ceilings or laid in floors including taking down of GI tubing and connection all as specified and directed.

S&F in repairs 15 mm dia bib tap cast copper alloy (fancy type), chromium plated, 'with crutch or butterfly handle, screwed down for iron pipe or for brass ferrule complete all as specified and directed.

S&F in repair 20mm dia brass chromium plated tubular towel rails, D type, 60cm long between flanges, complete all as specified and directed.

S&F in repair sinks made of stainless steel 1mm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar on to dwarf wall or including fixing cantilever brackets and connecting union to pipe, overall size 495mm x 420mm bowl size 410mm x 330mm x 160mm including waste pipe and waste coupling complete all as specified and as directed.

S&F in repairs gun metal globe or gate valve with iron wheel screwed bothedns for iron pipe of 15 mm dia complete all as specified and directed.

S&F in repairs galvanised mild steel wire cloth, 0.56mm nominal dia of wire and average width of aperture 1.18mm and fixed with tinned tacks or galvanesed wire stapels complete all as specifed and directed.

Taking down chowkats or frames with shutters (without taking off shutters from the frames) not exc. 1.5 Sqm each and removing from site complete all as specified and directed.

Taking down chowkhats or frames with shutters (without taking off shutters from the frame) exc 1.5 Sqm but not exc 4 Sqm each and removing from site complete all as specified and directed.

S&F second class hard wood plain, solid, straight, chowkat and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints complete all as specified and directed.

M&L for 30mm thick flush shutters, solid core construction with block board core & plywood face panels, commercial type on both sides complete all as specified and directed.

S&F 35mm thick second class hardwood factory made glazed and skeleton shutters open rebated and prepared to receive glass, gauze, etc divided into panels with plain or mitered shash bars any numbers of panels, edges of framing plain, chemfered or rounded, fitted with cut and mitred beads for securing glass, etc,sizes of members of shutters complete all as specified and directed

S&F galvanised mild steel wire cloth, 0.63mm nominal dia of wire and average width of aperture 1.40mm and fixed with tinned tacks or galvanesed wire stapels complete all as specifed and directed.

M&L for preparing surface of wood and wood based material and steel and iron work of any description and girth and treating ends of post, back of chowkats etc, area exc. 0.1 sqm and n.exc. 0.5sqm, with tar or coal tar or black paint complete all as specified and directed.

M&L for preparation of new wooden surfaces of any description over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and directed.

M&L for preparing surface of wood and wood based material and steel and iron work of any description and girth and treating small articles such as stop, covers, gully gratings, holdfasts, etc., area n exc 0.1 sq. m each complete all as specified and directed.

S&F mild steel bands, straps, clamps, holdfast, hooks, plain angle cleats for securing purlins, and similar small articles conforming to Fe 290 Gde E 165 as in hold fasts complete all as specified and directed.

M&F for PCC 1:3:6 type C-1 (using 20mm graded stone aggregates) as in bed blocks for hold fast kerbs etc complete all as specified and directed.

S&F Aluminium anodised barrel tower bolt 200 mm long of extruded section cast aluminium alloy complete all as specified and directed.

S&F Alluminium alloy anodised,sliding door bolt with hasp and staple (bolt type) and fixing clips of sheet,cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy and fixed 300mm long complete all as specified and directed.

S&F 150 mm size aluminium handles, cast type, anodised complete all as specified and directed.

S&F 125 mm size MS butt hinges medium weight cold rolled fixed with screw to frame complete all as specified and directed.

S& F glazed aluminum door powder coated of any colour consisting of frame of 63mm x 38 mm size with shutter fixed on frame both side openable on pivotal arrangement with including necessary cutting holes in wall & floor Door shutter consists of top rail & styles size is 83 x 44 mm & lock rail & bottom rail of size 110 x 44 mm & glazed with 5mm thick tinted /colour glass of approved make with handles 2 Nos in each door, hinges has fitted on frame as required fixed with rubber gasket & aluminum beading any No of panels with aluminum handle, locking arrangement, floor spring and floor door stopper incl. necessary joining cleats, glazing clips etc complete (Aluminium section thickness 2.00 mm} ) confirming to IS complete all as specified and directed..

S&F for winpire 3 track pre painted steel sliding window 3-track, 2 glass panel and 1 mesh panel ,sliding window fabricated from roll formed section made of galvanized steel colour coated/powder coated (base steel as per IS 513 D quality galvanized as per IS 277 with Zinc of 120gm/sqm ) with total coated thickness of 0.58mm primer coat with epoxy primer of 5-7 micron thick ,finish painted with a polyester paint of 12-16 micron thick and back coated with alkyd backer of 5-7 micron or powder coated with pure polyester up to 50-60 micron thick comprising the following:- (a) External frame section: 107mm x 44mm, (b) Shutter section: 35mm x 49mm (c) Section for mesh: 35mm x 49mm . (d) The window should be paneled with 5mm thick plain flot glass and stainless steel wire cloth with 0.36mm nominal dia of wire and average width of aperture 1.18mm. (e) Corner bracket for internal and external frame made of glass filled nylon. (f) Gaskets are to be made of Ethyl Propylene Diamine Monomer (EPDM) . The sections are to be cut to length, join and assembled by mean of corner bracket . Note:-The above frames should be fixed to the concrete/ masonary wall by means of self expanding screws Make: NCL ALLTEK & SECCOLOR LTD or equivalent make as approved by GE

S&F MS framed work such as grills gratings, sunshed cover fixed with nut bolts incl,cutting drilling holes etc., with ends of bars shouldered and/ or riveted, similar work conforming to Fe 290, Gde E 165 complete all as specified and directed.

S&F MS framed work as in doors or gates designer type of any section with gusset plates, rails, braces etc, complete, drilled for fixing of steel sheeting or other covering confirming to Fe 290 (Gde E 165) . Door, etc to be prepared for hanging or sliding with and including, either hooks and hinges or steel hanging door fittings and hanging; also fastening and fixing complete all as specicifed and directed.

M&L for applying two coats of synthetic enamel paint over a coat of red oxide or zinc chromate primer including preparation of new steel or iron surfaces exc 10 cm width or girth, complete all as specified and directed.

S&F 110mm PVC(SWR) bends with access door any radius complete all as specified and directed.

S&F 110mm PVC (SWR) pipes single socketed in any length with rubber ring joints laid in trenches or in floors, complete all as specified and directed.

S&F 75mm PVC (SWR) pipes single socketed in any length with rubber ring joints laid in trenches or in floors, complete all as specified and directed.

S&F 75mm PVC(SWR) bends with access door any radius complete all as specified and directed.

M&L 75mm dia PVC (SWR) floor trap, plain with grating including jointing with solvent cement complete all as specified and directed.

S&F in repairs 300 mm, mild steel ordinary rat rail rod pattern springs including roller plate complete all as specified and directed.

S&F in repair 25 mm bore stainless steel pipe curtain rods including stainless steel brackets & decorative dome, suitable for door/widows curtain with fancy type powder coated mild steel dooms with stailess stell brackets fitted to each end and fixed to wall incl. removal of existing rod and making good complete all as specified and directed

M&L for 600mmx600mmx7mm thick vinyl face, cinyl covered edges and washable metallized polyster foil backing, weight @ 5.6Kg/m2 suspended false ceilling comprising of non asbestos fibre cement bulding boards fixed or laid/inserted to GI frame work with screws over GI perimeter channel 0.55mm thick with two unequal flanges of 20 and 30 mm and web of 27 mm fixed to sourrounding wall using nylon sleeves and screws at 450mm centre to centre/ intermediate channel 0.9 mm thick having two equal flanges of 15mm each and web of 45mm suspended from soffit at approx 900mm centre to centre with GI cleat and steel expansion fastners with and including ceiling section (not exc 1.2m length) of 0.55mm thickness having kurled web of 50mm and flange of 26mm each with lips of 10.5 mm fixed to the intermediate channel with connecting clips across the intermediate channel at 457 mm center to centre including hangers 6mmm dia GI (upto 1200mm length) adjusting level fixed to roof slabs by means of ceiling cleats made out of GI flat 40x3mm size 60mm long including dismantling false ceiling any description or in any thickness, including cover fillets and complete all as specified. Make : ArmGyp-FB Ceilings (Armstrong) Model : Sleet (Alpha Lite) or equivalent make as approved by GE

Taking down copper/aluminium point wiring (light fan, socket or power) complete including fittings such as switch, sockets, c/rose, lamp holders, tube light fittings, sketch fitting , wooden boards, bell push, call bell, MCBs & regulators etc & making good to disturbed surfaces & matching with the existing colour of wall floor complete all as specified and directed

M&L for concealed point wiring for one light, fan point controlled by one switch with 1.5 Sqmm PVC-FR insulated, unsheathed, copper conductor, stranded 1100 volt grade cable in & incl PVC conduit, , including of junction and terminal boxes, all fittings such as tees, bends, elbows, etc. of External diameter 20mm all as per site requirements including anodized MS sunken boxes made out of MS sheet of thickness not less than 1.6 mm with earth dolly and PVC laminated hylem/Anchor ISI marked top cover 3.0 mm thick for mounting of switches/sockets/ regulator etc and PVC insulated & unsheathed 1100 volt grade copper conductor, stranded 1.5 sqmm. cable as continuous earth lead complete all as specified and colour coding of cables such as Phase - Red, Neutral – Black, and Earth – Green complete all as specified and directed

All as per Srl item No.71 above but one 5 Amp independent socket point controlled by one switch

All as per Srl item No.71 above but one 3 pin ,5 Amp socket point with other switch on the same board

All as per item No 71 here in before but for power point wiring using with 2.5 sqmm PVC insulated , unsheathed, copper conductor stranded 1100 volt grade cable and 2.5 sqmm PVC insulated ,unsheathed, copper conductor stranded 1100 volt grade cable as continuous earth lead complete all as specified and colour coding of cables such as Phase-Red, Neutral-Black and Earth-Green.

S&F switch piano type flush, single pole, one way, 5 Amp 230 Volt complete all as specified and directed

S&F socket outlet , 5 pin, 5 Amp flush, 230 Volt complete all as specified and directed

S&F switch piano type flush, single pole, one way,15Amp 230 Volt complete all as specified and directed

S&F socket outlet 2 in 1, 6 pin, 5/15 Amp ,flush type universal shuttered 230 Volt complete all as specified and directed

S&F ceiling rose, surface backlit, 63.5x48 mm three terminal complete all as specified and directed

S&F lamp holder with back plate suitable for Angle/Batten fitting with 9 watt LED bulb complete all as specified and directed

S&F testing and commissioning of MCB SP 6-40 Amp 240 Volt 10 KA capacity having C-curve characteristics connected with suitable lugs complete all as specified and directed

All as per Srl item No.81 above but SPN32- 63 Amps, 240 V

S&F in replacement sheet metal enclosure for DB double door, IP-43 when MCBs to be used SPN, 8 way, 240 V with 200 Amps rated bus bar including TW board of suitable size complete all as specified and directed

S&F electronic double space rotary step type 5 speed regulator 120- 280 V complete all as specified and directed

Taking down and refixing, connecting of ceiling fan after greasing complete all as directed by Engr-in-Charge.

S&F in replacement TL fitting 20 /18 watt for surface and wall mounted LED batten with ultra slim polycarbonate LED lighting fixture with high lumen output environmental friendly energy efficient complete all as specified and directed.. Make:- Havells Cat Part No LHEXBLP7PN1W020, 4 feet or eqvt in Bajaj cat part No BCLSB 20 WH/ CG Cat par No LCTC-18-CDL

S&F in replacement of 2 X 2 ultra slip recess mounted luminaire with high brightness 36 Watt LED package and Unique pattern acrylic de-glaring diffuser sheet for glare-free uniform light distribution suitable for armstrong/grid ceiling complete all as specified and directed Make-Havells cat part no PLANO2X2PLR36WLED857S/CG cat part no.LCPL-36-CDL(2X2)/Bajaj cat part no.BPSF 36W WH LED.

S&F in replacement concealed sub main wiring with 2 single core PVC insulated, unsheathed copper conductor stranded 1100 volt grade cable of size 6 sqmm FR drawn in and incl PVC rigid conduit medium grade of size not less than 20 mm dia ISI marked ivory white with all accessories such as tee, bend, joint cover etc PVC insulated, unsheathed copper conductor stranded 1100 volt grade cable of size 6 sqmm FR cable as continuous earth lead complete all as specified and colour coding of cables such as Phase-Red, Neutral-Black and Earth-Green

Supply and laying in replacement cable XLPE insulated armoured heavy duty electric cable with aluminium conductor, 1100 volt grade cross sectional area 16 sqmm 2 core all as specified and directed.

Excavation in trenches n. exc 1.5 mtr wide and n. exc 1.5 mtr depth for laying of cable as the case may be and getting out in hard/dense soil complete all as specified and directed.

M&L for sand cushioning in trenches for the cable complete all as specified and directed

Returning filling, spreading, leveling, watering and well ramming in layers n. exc 25 cm thick complete all as specified and directed

Removing excavated surplus material n. exc 50 mtr and depositing where directed at a level n. exc 1.5 mtr from starting point complete all as specified and directed.

M&L for kiln brunt bricks sub class B laid in trenches for cable protection complete all as specified and directed

S&F in replacement GI Pipe light grade 40mm dia ISI marked on pole on wall or laid in trenches incl all fittings (nut, bolt, clamps & washers) complete all as specified and directed

M&L for provn of earthing complete with MS galvanized earth plate electrode 600x600x6 mm thick buried directly in ground ( earth pit not less than 2.25 M deep below normal GL) with top edge of plate not less than 1.5 M below normal ground level connected to galvanized earth lead wire 4 mm dia by means of bolts, nuts, check nuts and washers of CI or steel incl excavation, PCC (1:3:6) type C-1 chamber with CI cover 10 mm thick, 15 mm dia light grade , GI protection pipe, funnel with wire mesh, watering pipe of size 20 mm dia, medium grade, lugs, main earthing lead upto main switch/DB incl charcoal dust, salt etc all as shown in electrical plate No. 3 of SSR part-I 2009 specification.

M/s Mohan Singh

M/s Vinod Kumar Korpal, Sagar

anil kumar sahu

M K Construction

A Raza Enterprises