Construction of RCC Sluice culvert at Darika bund Right bank from AT Road to Dhaiali near Rajadhap.

Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m 2.8.1 All kinds of soil.

Earth work in filling by mechanical means by deploying hydraulic excavator and trippers etc. including ramming with locally available ordinary soil excluding rocky soil with all lead and lift, transporting to site, spreading, dressing as per design section including ploughing or roughening or benching the seats, removing all debris, breaking clods up to 2.5 cm cube, etc. complete as directed.(12.5 % deduction will be made from the section measured quantities of the completed and compacted earth work on account of shrinkage) For initial lead up to 1 Km and for all lifts

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:2:4 (1 cement : 2 coarse sand (zone-III) derived from natural sources : 4 graded stone aggregate 20 mm nominal size derived from natural sources)

Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level : 1:1.5:3 (1 cement : 1.5 coarse sand (zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources)Plastering with cement mortar (1:3) on stone masonry in sub-structure work as per Technical specification

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level.

Centering and shuttering including strutting, propping etc. and removal of form for Foundations, footings, bases of columns, etc. for mass concrete

Collection and supply of broken stone metal of size 20 mm to 38 mm from hard blasted rock from Bihubor quarry free from dust, dirt and other foreign materials screening properly, stacking in suitable stacks at work site, payment of forest royalty monopoly,etc. complete as directed.

Collection and supply of river boulder of size 23cm to 30cm in average and minimum weight 30 kg having i. Specific gravity not less than2.65, ii. Aggregate Chrustingb<30%(Wearing)&<45%(Non-wearing) iii. Impact value (%) max <30%(Wearing) & <45%(Non -Wearing ) and iv.Abrasion Value (0%)<30%(wearing )&<50%(Non wearing) ( Materials confirming to IS2386 part III& IV1963) free from dust, dirt and other foreign materials including necessary carriage and stacking in regular measurable stacks at site, monopoly ,etc. complete as directed. ( 10% under sized (not less than10cm)boulder is allowable for packing /filling the gaps occurred during execution of works) complete as directed. (15% deduction will be made from the stack measured quantities on account of void) .

Labour charge for making filter bed of required thickness with stone metal of size 13mm to 38mm over the trimmed surface of river bank/embankment., slope, including site carriage of metal within a distance of 150m etc. complete as directed . 5.06.1 (Without Boat)

Labour charge for laying and pitching boulder of 23 cm to 30 cm size (man size) including dressing the seat, ramming to proper size & slope, properly hand packed including site carriage of boulder from stacks within a distance of 150m etc. complete as directed. 5.05.1 Without boat

Providing and laying of apron with cement concrete blocks of size as per Table 1300.1 cast-in-situ and made with nominal mix of M-15 grade cement concrete as per drawing and technical specifications Clause 1301

Construction of whole bamboo single palisading with matured Bhaluka bamboo posts 7.5 cm to 10 cm dia., 15 cm clear apart 1.50 m to 1.80 m above ground and 1.00 m to 1.20 m below ground with Bhaluka bamboo inclined struts placed at 1.5 m a part tied with three rows of horizontal half Jati bamboo kamies etc. complete as directed. (Using Bhaluka Bamboo at the rate of 10.14 nos./Rm & Jati Bamboo at the rate of 2.40 nos./Rm)

Construction of temporary shed of two roof with mud plinth of o.45m height above ground level with bhaluka bamboo post 1.5m apart driven at least 0.75m below ground and height above plinth of 2.50m split Jatti bamboo /tarza wall 10cm thick thatched roofing over bamboo rua frame placing at 0.15m clear apart, fitted with bamboo kamies from binding doors and windows with bamboo chattai,strengthening with bamboo frame binding with wire ,roofing withy TATA shaktee roofing sheet etc . complete as directed. (Using Bhaluka bamboo at the rate 61.00 nos /rm)

Serviceable empty cement bags

Labour charge for filling of empty cement bags to attain minimum filled up volume of 0.028 Cum with filled up size of 0.7 m × 0.40 m × 0.10 m, laying and pitching of the earth filled cement bags including excavation and borrowing earth, breaking clods, filling in bags and supplying and stitching the mouth with jute sutli, etc. complete as directed. (Cement bags will be supplied by the department free of cost). For borrowing earth from a distance beyond 30 m. & up to 60 m.

Dewatering by 5 H.P. water pump including supply of necessary fuel, engine oil and pump operator etc complete.

Fabrication of shutter :- M.S. Plate 6 mm thickness for skin plate,frame for box type shutter.

Fabrication of shutter :- M.S. Channel 150 x 75 x 6mm for shutter stiffener.

Fabrication of shutter :- M.S. Plate 10 mm for making Bracket for shaft pin, wire rope, Roller box etc.

Fabrication of shutter :- M.S. Flat 50 x 6 mm for rubber seal fitting.

Fabrication of shutter :- M.S. Angle 75 x 75 x 6mm.

Fabrication of shutter :- "J" type Rubber seal 125 mm.

Fabrication of shutter :- Making & supply of C.I. roller with suitable collar 10 -12 mm & centre hole 10 - 20 mm as per direction (Machine finished), size (dia. × height). a) 100 mm × 150 mm

Fabrication of shutter :- F' shaped roller bracket made of 10 mm thick plate of size 75 × 200 mm with hole as per direction to accommodate with the roller size: (Machine finished) a) 100 mm × 150 mm

Fabrication of shutter :- C.I. roller pin of length 150 mm to 250 mm dia. (Machine finished) a) 16 mm

Fabrication of shutter :- Nuts & Bolts (Assorted size)

Fabrication of shutter :- M.S. Washer (Assorted size)

Fabrication of shutter :- W.B. Grease

Fabrication of shutter :- Waste Cotton

Fabrication of shutter :- Welding by gas or electric plant including transportation of plant at site etc. copmlete

Fabrication of operating and lifting system for the single opening sluice :- M.S. Screw shaft 75mm

Fabrication of operating and lifting system for the single opening sluice :- Thread cutting @ 2PTI on 75mm dia including turning,straightening & finishing.

Fabrication of operating and lifting system for the single opening sluice :- C. I. Boss size (150 x 200)mm

Fabrication of operating and lifting system for the single opening sluice :- H.D. thrust bearing 75 mm

Fabrication of operating and lifting system for the single opening sluice :- C.I. counter weight circular type 1.5" thick with 25 mm dia. hole & weight of 35 Kg each as per direction (machine finished & fine grinded)

Fabrication of operating and lifting system for the single opening sluice :- Counter weight holder

Fabrication of operating and lifting system for the single opening sluice :- C.I pulley 16 mm to 25 mm dia. with centre hole as per direction (Machine finished) a) 125 mm

Fabrication of operating and lifting system for the single opening sluice :- C.I.Pulley 150mm

Fabrication of operating and lifting system for the single opening sluice :- M.S. base plate 300 mm × 300 mm of the following thickness as per direction including supply of materials. (Machine finished) a) 10 mm

Fabrication of operating and lifting system for the single opening sluice :- M.S. lock plate 300 mm × 300 mm of the following thickness as per direction including supply of materials. (Machine finished) a) 8mm

Fabrication of operating and lifting system for the single opening sluice :- Nuts & Bolts (Assorted size)

Fabrication of operating and lifting system for the single opening sluice :- M.S. Washer (Assorted size)

Fabrication of operating and lifting system for the single opening sluice :- Pulley stand made of 100 × 50 mm channel for (As per direction) a) 125 mm

Fabrication of operating and lifting system for the single opening sluice :- Pulley pin of 16 mm dia.

Fabrication of operating and lifting system for the single opening sluice :- Steel wire rope (Tested quality) of the following sizes (ISI standard) b) 19 mm

Fabrication of operating and lifting system for the single opening sluice :- "U" clamp of size b) 19mm

Fabrication of operating and lifting system for the single opening sluice :- Shaft pin with length up to 150 mm for the following diameters c) 20 mm dia

Fabrication of operating and lifting system for the single opening sluice :- Distant tube with pin of the following size (Machine finished) b) 100 × 12 mm

Fabricating and Installing of Guide channel, Top and Bottom channel for sluice :- Channel size 200 X 75 mm for guide instalation.

Fabricating and Installing of Guide channel, Top and Bottom channel for sluice :- 200 X 75 mm channel for bottom channel.

Fabricating and Installing of Guide channel, Top and Bottom channel for sluice :- Separator stud with nut on both end with tube of length 250 mm to 460 mm

Fabricating and Installing of Guide channel, Top and Bottom channel for sluice :- M.S. Plate 10mm for guide channel base connection

Fabricating and Installing of Guide channel, Top and Bottom channel for sluice :- M.S. Angle 75 x 75 x 6mm for anchoring.

Fabricating and Installing of Guide channel, Top and Bottom channel for sluice :- Nuts & Bolts (Assorted size)

Fabricating and Installing of Guide channel, Top and Bottom channel for sluice :- C.I pulley 16 mm to 25 mm dia. with centre hole as per direction (Machine finished) a) 125 mm

Fabricating and Installing of Guide channel, Top and Bottom channel for sluice :- Electric arc welding

Fabrication of the Plateform and Gateway :- M.S. Plate 6mm.

Fabrication of the Plateform and Gateway :- M.S. Angle 50 x 50 x 6 mm for cross bar , railing.

Fabrication of the Plateform and Gateway :- M.S. cross channel 100 x 50 x 4.7 mm

Fabrication of the Plateform and Gateway :- M.S. Channel 200 x 75mm, for support bar.

Fabrication of the Plateform and Gateway :- Electric arc welding

Commissioning of the work :- Grease (HD)

Commissioning of the work :- Nuts & Bolts (3/8",5/8",7/8")

Commissioning of the work :- M.S. Washer

Commissioning of the work :- Hire charges of diesel trucks with driver and helper but excluding fuel and lubricant. (c) 10 Ton Capacity

Commissioning of the work :- Cost of Diesel

Commissioning of the work :- Lubricant cost

Commissioning of the work :- Ordinary Labour

Commissioning of the work :- Applying priming coat : With ready mixed red oxide zinc chromate primer of approved brand and manufacture on steel galvanised iron/ steel works.

Commissioning of the work :- Applying priming coat : With ready mixed red oxide zinc chromate primer of approved brand and manufacture on steel work (second coat)

Commissioning of the work :- Painting with synthetic enamel paint of approved brand and manufacture to give an even shade : 13.61.1 Two or more coats on new work