Construction of Balance Work of Student Hostel at the permanent campus of Indian Institute of Management Shillong Umsawli Meghalaya

Amount

Total Amount of BoQ 2

Amount after unconditional Rebate

Description of Work / Item(s)

Amount

Total of BoQ 3, BoQ 4, BoQ 5 and BoQ 6

Total Amount of BoQ3 (Item Rate)

Total Amount of BoQ4 (Percentage Rate)

Total Amount of BoQ5 (Percentage Rate)

Total Amount of BoQ6 (Percentage Rate)

Description of Work / Item(s)

Amount

Schedule - (D) Bill of Quantites for Non Schedule Items (MR ITEMS) (Civil and Electrical)

NS 1-Supplying and applying Anti termite treatment with providing chemical (Imidaclprid 30.5 SC) shall be used at 0.075% concentration (2.1 ml of chemical mixed in 1 ltr of water OR in other words mixing ratio of chemical to water is 1:475) with water by weight at the rate of 5 Liters per sq. m.of the surface before sand bed is laid. (For top surface of the consolidated earth at plinth holes upto 50 mm. to 75 mm. deep at 150 mm. center to center both ways shall be made with 12 mm, diameter mild steel rod on the surface to facilitate saturation of the soil and also to the Foundation bed ,Basement excavation, back filling Vertical side, Plinth & extended portion ,Soil Surrounding Pipes, Wastes and Conduits, special care at below construction joints, beneath Junction of the Wall and the Floor etc. with the chemical as above) .The work should be carried out as per specification described in para 6.4 of code IS-6313 (part-2&3) 2013 by a specilised agency duly preapproved. (Mode of measurement will be per Sqm of Plinth area of the Building as per Drawing.)

NS 2 - Providing and fixing at all heights and depths 50 MM thick premoulded joint filler board for expansion joint having minimum density 95kg./ cum, Non standing with less than 1% water absorption and compression recovery of 93% minimum as per manufactured specification including cost and conveyance of all materials, cutting and placing to the required size, labour charges, sundries, wastage etc. at all levels complete as per drawings and as direction and satisfaction of Engineer-in-charge.

NS 3 -Supplying, laying and fixing of std. chicken wire mesh flexible galvanized steel wire with hexagonal gaps. Available in 1 inch (about 2.5 cm) diameter, wire gauges 19 gauge (about 1 mm wire) to 22 gauge (about 0.7 mm wire). in positions at junctions of concrete & masonry works all complete as per specification, drawing and instructions of the Engineer in charge.

WOOD WORK (price range indicated for basic material should have allowed variation of price upto 5%)

NS 4 -Providing & fixing Stainless steel Fastener Bolt (10mmx 120mm) for Door Frame fixing complete in all respect.

NS 5- Providing and fixing ISI marked flush door shutters conforming to IS: 2202 (Part I) non-decorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters:(a) 35 mm thick including fixing with butt hinges with necessary screws. (Butt hinge paid in separate items)

NS 6- Supplying SS Butt hinge with Square edge, 8 nos. zigzag screw hole & SS finish pintype Butt Hinge (Reference price range Rs. 175 per piece) 125mm x 65mm x 2.5mm (Minimum) including necessary size SS Screw as per approved make

NS 7- Providing and fixing SS (Grade 304) pull handle of approved design/Type with necessary screws etc. complete in all respect

NS 7.1- SS finish Mortise handle type/ any shape as per approved design (Reference price range Rs. 1930/-Per pair 250mmx22mm or equivalent)

NS 8- SS finish Mortise handle type/ any shape as per approved design (Reference price range Rs. 1841/- per pair 200mmx22mm or equivalent )

NS 9- Providing and fixing SS (Grade 304) Mortise Dead Lock without handle operated one side key & otherside knob with cylinder , Lockbody, Key head and Left & Right operation of approved design/Type with necessary screws etc. complete in all respect :

NS 9.1- SS finish Lock with Minimum 3 keys (Reference price range Rs. 2080/--per no. for Lock body, Cylinder & Master Key )

NS 10- Providing and fixing SS (Grade 304) hanging floor door stopper of superior quality with necessary screws etc. complete in all respect:

NS 10.1-Door mounted hanging type Door stopper (Reference price range Rs. 334/-per no.)

NS 11- Providing and fixing stainless steel Tower bolt of superior quality(Grade-304) with nuts and screws etc. complete in all respect:

a) 250x10 mm (Reference price range Rs. 295/- per no.)

NS 12- Providing and fixing SS (Grade 304) Aldrop of approved design with necessary nuts & screw etc. complete in all respect.

a) 16mm dia boltx200 mm long (Reference price range Rs.1430/- per no.)

NS 13 -Providing and fixing Rubber /PVC buffer (Reference price range Rs. 37/- per no.) of required size and of approved quality with necessary screws etc. complete in all respect

NS 14 -Providing and fixing Door Closer SS finish upto 80kg including necessary fixture, screw etc. (Reference price range Rs. 3850/- per set.) complete in all respect

NS 15 -Providing and fixing Soft close sliding system for framed wooden flush door of approved make including necessary top track of required length, accessories, fixture, screw etc. (Reference price range Rs. 4390/-for sliding system with Accessories + 6700/- for top track per set.) complete in all respect .

NS 16 -Providing and fixing SS Door Handle with Lock for sliding flush door of approved make including necessary fixture, screw etc. (Reference price range Rs.4472/-for Handle & Lock per set.) complete in all respect .

ALUMINIUM DOORS, WINDOW WORK: (price range indicated for basic material should have allowed variation of price upto 5%)

NS 17 - Supply and fixing Dash fastener as per required sizes for fixing of Door & Window aluminium Frame.

NS 18 - Providing and fixing glazing with required EPDM rubber / neoprene gasket etc. For window glazing:- With coloured toughened glass panels of 8.0 mm thickness (ST 467 of Saint Gobain or equivalent) having Visible Light Transmission (VLT) of 54.0 to 56.0 %, External reflection 14.0 to 21.0 %, Internal reflection 18.0 to 27.0 %, Solar factor 0.40 to 0.60, Shading Coefficient 0.50 to 0.60 and U-Value (W/sq. .m. K) 3.00 to 5.62. Rate include additional aluminium sections, friction hinges, handle, safety chain and other accessories as applicable.

NS 19- Design, supply fabricate and fixing Semi Utilized Structural Glazing system with single glazing 8mm thick toughned of approved colour & sample (ST 467 AND ST 436 OF SAINT GOBAIN OR EQUIVALENT) securely bonded to framework to ensure absolute water tightness, with profile either straight or segmented curve in plan consisting of main panel work of Mullions and Transoms made out of specially designed extruded aluminium section having 15-20 Micrones Anodized in approved colour. Fixed at all levels,elevation and heights to the RCC elements with necessary clamps,brackets and anchor fasteners, made of shall be Mild steel Hot Dip galvanized with washer and shall confirm to IS : 4759 -1996. All gaskets shall be EPDM with all necessary flashing,floor seal,smoke seal, sealents etc. to make system fully weather and sound proof & water tight. Proposed glazing should be bonded to frame by mean of Structural sealant of Dow corning 995 and weather sealant shall be Dow Corning 789. All spacer tape should be Nortan or equivalent etc. complete with fixing inclusive of all hardware supply , fixing ,Glass will be paid in this Glazing items.

NS 19.1 - For Vision area:-With coloured toughened glass panels of 8.0 mm thickness (ST 467 of Saint Gobain or equivalent) having Visible Light Transmission (VLT) of 54.0 to 56.0 %, External reflection 14.0 to 21.0 %, Internal reflection 18.0 to 27.0 %, Solar factor 0.40 to 0.60, Shading Coefficient 0.50 to 0.60 and U-Value (W/sq. .m. K) 3.00 to 5.62. Complete in all respect including frame, glass & necessary hardwares as per approved shop drawing and direction of the Engineer - in - charge.

NS 19.2 - For Spandral area:-With coloured toughened glass panel of 6.0 mm thickness (ST 436 of Saint Gobain or equivalent) having Visible Light Transmission (VLT) of 30.0 to 56.0 %, External reflection 16.0 to 19.0 %, Internal reflection 17.0 to 27.0 %, Solar factor 0.35 to 0.50, Shading Coefficient 0.40 to 0.55 and U-Value (W/sq. .m. K) 5.40 to 3.3. Complete in all respect including frame, glass & necessary hardwares as per approved shop drawing and direction of the Engineer - in - charge.

NS 20 - Supplying and fixing Hinges/ Staying Hinges for Aluminium Door & Windows of approved quality all complete as per drawing or as directed. (Reference price range Rs. 320/-Per each)

NS 21 - Supplying and fixing Handle with Lock for Aluminium Casement Windows Left & Right operation all complete as per drawing or as directed. (Reference price range is Rs. 200/-)

NS 22 -Supplying and fixing aluminium Louvers (fixed type) of approved integrated anodised ( matt finished 15 micron thick) extruded sections . all complete as per drawing or as directed.Minimum weight 8 kg / sqm.

NS 23 -Providing & Fixing H-type Door Pull Handle for Glass/Aluminium Door Shutter.32mm dia X600mm overall Length, material SS 304, SS finish with necessary screw etc. complete in all respect. (Reference price range Rs 3208/- per pair)

NS 24 - Providing and fixing Floor Spring upto 120 kg door weight including top & bottom pivot, necessary accessories, screw etc. complete in all respect

NS 24.1 -For Aluminium Door (Reference price range Rs. 5175/- per set.)

STEEL WORK (Metal door)

NS 25 - METAL(MS) DOOR :-Supplying and fixing 30mm/35mm thick (at any level) Factory made MS non fire rated Door Shutter having 1.2 mm thick sheet bothside, C channel supported by sufficient stiffner as per drawing with door Frame of Pressed Galvanized steel confirming to IS 277 having 1.6mm thick sheet including Transfer grill,vision panel, finishing with paint over primer fittings & fixture and including all necessary Hardware ,as per Drawing & Design with the direction of Engineer in Charge complete in all respect. (Sample of each Door Should be approved before procurement)

NS 25.1 -35mm thick Metal Door SIZE 1000MM(W)X2100MM(H)single Shutter, frame Including MS Hardware.(4nos. 100mmx75mmx3mm MS Butt Hinge, 1no.250mm Long D-Type MS Handle Fabricated MS 20mm dia ROD, 1 no.250mm MS Aldrop, 1 no.300mm MS Tower Bolt, as per Drawing Finished painted as per approved colour) complete in all respect.

FIRE DOOR

NS-26 :Fire rated Door Frame:-Fire Door frame 2hrs FIRE RATED shall be double rebate profile of size 143 x 57 mm made out of 1.60mm (16gauge) minimum thick galvanized steel sheet. Frames shall be Mitered and field assembled with self tabs. All provision should be mortised, drilled and tapped for receiving appropriate hardware. Rubber door silencers should be provided on the striking jamb. Frames should be provided with back plate bracket and anchor fasteners for installation on a finished plastered masonry wall opening. Once frame installed should be grouted with cement & sand slurry necessary for fire doors on the clear masonry opening.

NS-27 : Fire rated Door Shutter-Fire Door DOUBLE/SINGLE leaf 2hrs FIRE RATED shall be 46mm thick fully flush double skin door with vision fire retardent glass. Door leaf shall be manufactured from 1.2mm minimum thick galvanised steel sheet with fire retardent primer and paint. The internal construction of the door should be rigid reinforcement pads for receiving appropriate hardware. The infill material shall be resin bonded honeycomb core. All doors shall be factory prepped for receiving appropriate hardware and provided with necessary reinforcement for hinges, locks, and door closers. The edges should be interlocked with a bending radius of 1.4mm. For pair of doors astragals has to be provided on the meeting stile for both active and inactive leaf. Vision lite wherever applicable should be provided as per drawing & design with a beading and screws from inside. The glass should be 6mm clear borosilicate fire rated glass of relevant rating of the door. (GLASS PANEL, HARDWARE WILL BE PAID IN SEPARATE ITEM.

FOR DOOR SIZE- 1200MM(WIDTH)X2100MM(HEIGHT) Single Leaf Shutter.

NS-27.1 :Providing & fixing SS 304 Fire rated Ball Bearing But Hinges 100X 75X3MM,ss 304 (For Fire Metal Door)

NS-27.2 : Providing & fixing SS 304 Fire rated Surface door closer, with standard arm, silver finish (For Fire Metal Door)

NS-27.3 :Providing & fixing Fire rated Panic Bar (For Fire Metal Door)

NS-27.4 : Providing & fixing Vision panel of 6mm thick borosilicate Fire Rated clear glass , Self adhesive side roll (Ceramic Tape) as required (For Fire Metal Door)

NS-27.5 : Providing & fixing Fire rated seal for grooved frame (For Fire Metal Door)

NS-27.6 :Providing & fixing concelled flush bolt SS finish 300mm long (For Fire Metal Door)

FLOORING

NS 28 - Providing and laying (Matt/Antiskid) Ceramic floor tiles of size as mentioned below (thickness to be specified by the manufacturer), of 1st quality conforming to IS : 15622, of approved make and approved colours and design, laid on approx. 20 mm(or more) thick Cement Mortar 1:4 (1 Cement : 4 Coarse sand), jointing with grey slurry @ 3.3kg/sqm including pointing the joints with white cement and matching pigments etc., complete with all lead ,lift & matching with adjacent floor / slope.

a) 300mmx300mm

NS 29 - Stone work (machine cut edges) for wall lining etc.(veneer work) backing filled with a grout of 12mm thick cement mortar 1:3 (1 cement : 3 coarse sand) including pointing in white cement mortar 1:2 (1 white cement : 2 stone dust) with an admixture of pigment matching the stone shade.

NS 29.1 -Cherra Stone of size 250X100X15

NS 30 - Providing & Laying Stone guard coating as per approved make over Cherra Stone after necessary preparation of surface at any level complete in all respect as per direction of Engineer-in-charge & specification of the manufacturer.

NS 31 - Providing and laying Double charge Vitrified floor tiles (Matt finished) in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS : 15622 of approved make , in approved colours and design, laid on approx. 20mm (or more) thick cement mortar 1:4 (1 cement : 4 coarse sand), including grouting the joints with white cement and matching pigments etc...,complete with all lead ,lift & level matching with the adjacent floors / slope.

NS 31.1 - For Matt Finish of Sizes 600mmX600mm

NS 32 - Providing and laying Double charge Vitrified tiles in different sizes in skirting (thickness to be specified by manufacturer), with water absorption less than 0.08 % and conforming to I.S. 15622, of approved make, in approved design & colour, in dado, skirting, riser of steps, over 12 mm thick bed of cement mortar 1:3 (1 cement: 3 coarse sand), including grouting the joint with white cement & matching pigments etc. complete with all lead & lift.

NS 32.1 - For Matt Finish of Sizes 600mmX600mm .

NS 33 - Providing and fixing 20mm thick semi polished Kota stone slab for window sills and similar locations of required size of approved shade, colour and texture laid over 20mm thick base cement mortar 1:4 (1 cement : 4 coarse sand) with joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edge to give high gloss finish etc. complete at all levels.

NS-34 Providing & laying Granite slabs 18 mm thick in risers of steps, skirting, dado and pillars laid on 12 mm (average) thick cement mortar 1:3 (1 cement: 3 coarse sand) and jointed with grey cement slurry mixed with pigment to match the shade of the slabs, including rubbing and polishing complete. Flamed finish granite stone slab Jet Black, Cherry Red, Elite Brown, Cat Eye or equivalent.

FINISHING

NS 35 - Outside Textured with paint WITH LOW VOC:-Providing and applying a uniform 2mm (+/- 0.25mm) thick Dolomite filler based Acrylic Texture of approved design/pattern with necessary primer (ON THE BASIS OF FREE MOCK UP/SAMPLE), including pre-preparation of the surface as per manufacturers specifications, approved sample panel, drawing & as directed by the Engineer-in-charge complete in all respect at all level.

ROOFING AND WATER PROOFING WORK

NS 36 - Surface Preparation for water proofing:-Cleaning the surface to make it dust free and sludge free, removing any extended portions by grinding and if required using suitable equipment. The mother slab has to be laid in slope to ensure proper drainage through the drain openings. All surfaces to be waterproofed should be sound, clean and dry. Concrete surfaces should have a light steel-trowel followed by a fine hair-broom or equivalent finish which is dry and free of dust, oil and other contaminants. All high spots should be removed.

NS 37 -Crack treatment & Coving :- Any surface cracks shall be chased open into a ‘V’ groove, and filled with cement mortar mixed with acrylic polymer emulsion (STP LTD/SIKA/FOSROC TERRACO/PIDILITE /ROFFE/LATICRETE/JBM or Equivalent) @ 4% by weight of cement. Coving the junctions of the Vertical wall and Roof slab with fillet of size 75mm x 75mm fillet of mortar (Cement: sand – 1:4) admixed with acrylic polymer emulsion . Before chamfering a prime coat shall be given with the slurry of acrylic polymer emulsion .Special care shall be taken to ensure proper coating of the inner surfaces of the drain openings in the wall. Sealing the joint between PVC and masonry with Polyurethane elastromeric sealant of Approved manufacturer.

NS 38 - Application of primer ( with ShaliCrete & two parts of neat cement i.e. in the ratio 1 : 2 of ) on the prepared surface to seal the pores as per manufacturer's specification

NS 39 - Roof Water proofing:-Supply and apply appropriate membrane product of minimum thickness 1.5mm (Elastomeric Waterproofing of STP Limited/SIKA/FOSROC TERRACO/PIDILITE /ROFFE/LATICRETE/JBM or Equivalent ) by applying in roof slab & Parapet Wall upto 450 mm as per approved manufacturer specification.

NS 40 - Providing & Laying M:25 Grade Screed conc. over treated roof average 40mm thick including laying approved quality GI Chiken wire mesh. Mixing with water proofing compound of approved manufacturer with specified ratio,maintaing proper slope & finishing at outlet of pipe and making hallor at the juction of roof & parapet, curing complete in all respect as per satisfaction of the Engineer in Charge et

NS 41 - Lift pit Water proofing :-Supply and application of a non shrink, expanding grout admixture with suitable material (Sika Intraplast EP/FOSROC Brushbond RFX/Shaligrout PU) of approved manufacturer with their direction, by pressure grouting inside RCC floor & treated wall upto Ground Floor (upto 3.00mtr.) after 28 days of curing using 12mm dia, 75 mm long GI nozzles 1.5 m C/C in the concrete.Next Supply and application of an water proofing inside RCC floor & wall upto plinth appropriate coating of approved manufacturer with their direction. (Rate is inclusive of necessary repair for damage portion after installation of Lift )

NS 42 - Wet floor Water proofing:-Supply and apply water proofing coating of minimum thickness 2mm (Topseal 107/Brushbond RFX/Shalicem EWP ) on floor, polymer modified product as per approved manufacturer with their direction.

NS 43 - Wet wall Water proofing :- Supply and application of water proofing inside floor & wall upto full height & cover 300mm upto outside with appropriate material of minimum thickness 1.5mm (Sika LASTIC 450 I/ Nitoproof 600 FOSROC/BASF Master Seal HLM 5000)of approved manufacturer with their direction.

NS 44 - Providing and applying 1 coat of Solvent based Cement Primer and 2 coats of Acrylic Emulsion of approved shade, complete as per manufacturers specifications, drawing & as directed by the Engineer-in-charge.

NS 45 - Providing & fixing at all height steel profile sheet of effective width 1072 mm and nominal 28.5 mm deep ribs with subtle square fluting in the five pans at nominal 203 mm center-to center, matching with the existing buildings. The end rib shall be designed for anti-capillary action, to avoid any seepage of water through the lateral overlap. The feed material used as per AS/NZS 2728 Type 4 and of (TATA BLUESCOPE/MULTICOLOR STEEL PENNAR/ DYNAROOF/ BHP/LLYODS or equivalent make) with nominal 0.42 - 0.45 mm Base Metal Thickness and total coated thickness ( TCT) 0.47 - 0.5 mm of Hi Strength with minimum 550 MPa yield strength, AZ150 (Min. 150 g/m2 total of both sides) hot dip metallic coating of 55% Aluminum- Zinc to AS 1397 and Lead free Super Durable paint top coat with inorganic pigment. The total paint coat thickness shall be nominal 35 μ comprising of nominal 20 μm exterior coat on top surface and nominal 5 μm backer coat on reverse surface over nominal 5 μm primer coat on both surfaces of approved color shade by concern authority. The feed material should have coil manufacturer’s product details marked at regular interval.(Colour to match with existing buildings)

NS 46 - Providing & fixing Flashings upto 900 mm girth: COLORBOND® steel of Tata Blue scope or Equivalent with necessary fittings & fixture complete in all respect

NS-47- Providing & fixing at all height steel plain sheet of 1220 mm girth the steel base material of sheet shall be manufactured from 0.45 mm (nominal) base metal thickness with minimum 550 MPa Yield Strength. The sheets shall have a hot dip metallic Aluminium-Zinc alloy coating of Aluminium (55%) & Zinc (45 %) with total mass coating of 150 gms/sq.mt on both sides as ZINCALUME® AZ150 or equivalent coating as per AS 1397. The coated sheets shall be factory painted and oven-baked conforming to AS/NZS 2728 type 3- 4, the total coating thickness of 35 μm (nominal) of COLORBOND® steel quality paint system, comprising of nominal 20 μm exterior coat on top surface and nominal 5 μm reverse coat on back surface over nominal 5 μm primer coat on both surfaces of approved colour shade.

NS 48 - Providing & fixing 12mm thick Cement fibre board of approved make on existing frame at any height with necessary screw, nuts & bolt etc. complete in all respect

MISCELLANEOUS

NS 49 - Supply and apply a polyurethane based elastic, sealant gun grade for expansion joint Including complete installation as per manufacturer’s method statement including cleaning of the joint, repair of the joint edges (if required), backer rod, primer, finishing etc. Primer: Shal Prime PUM or equivalent , Sealant: ShaliSeal PU GG or equivalent , Expansion joint section: 40 mm (Width) X 20 (Depth) mm. at the time of finishing work like plastering as directed by Engineer –in-charge as per manufacturer's specification at all heights and depths including necessary backing rod conforming to IS: 1838, all to make the job complete.

NS 50 - Supply and apply a flexible FPO based membrane for expansion joint width 50 mm or as per width size tape Product: STP LTD./ SIKA /FOSROC or Equivalent : For upto 50 mm gap size 150 mm x 2 mm or for upto 100 mm gap size- 200 mm x 2 mm or for upto 200 mm gap size 300 mm x 2 mm . Chemical Base Modified flexible Polyolefin (FPO) with advanced adhesion Fire Rating Euroclass E (EN ISO 11925-2, classification to EN 13501-1) Service Temperature -30°C min. to +40°C Supply and apply an epoxy based membrane adhesive base coat & top coat of approved make . Consumption: 1.2 kg/m (strip width 150 mm) Product requirements: mixed density: 1.75 kg/ltr; bond strength > 1.5 N/mm2. The rate includes the repair of edges, backing material , tools tackles etc. all complete. Providing and cleaning the substrate edges , repairing the edges with high strength repair mortar to ensure the gap remains as per drawing. The rate includes the repair of edges, backing material , tools tackles etc. all complete. For gap above 100mm, upto 200mm, tape size 300mm x 2mm : internal and external use.

SANITARY FIXTURES AND FITTINGS

NS 51 - Providing and fixing white vitreous china pedestal type water closet (European type) P or S trap as applicable of approved model & flushing cistern minimum 3 litres capacity, seat and lid, including flush pipe, with manually controlled device, overflow arrangement with all specials, fittings of standard make of approved municipal design complete, with flush plates all complete or make including cutting and making good the walls and floors wherever required complete in all respect as per Enginerr in charge: (PARRYWARE / HINDWARE / CERA / JAQUAR or equivalent).(Reference price range Rs.9782/-)

NS 52- Supplying, fitting and fixing C.P on brass Bib cock of approved model with wall flange, including cutting and making good the walls wherever required complete in all respect as per Enginerr in charge{Jaquar/MARC/ ESSCO/ KOHLER or equivalent}(Reference price range Rs.881/-)

NS 53 - Supplying, fitting and fixing C.P on brass Two way Bib cock of approved model including cutting and making good the walls wherever required complete in all respect as per Enginerr in charge.{Jaquar/ MARC/ESSCO/ KOHLER or equivalent}(Reference price range Rs.1031/-)

NS 54 - Supplying, fitting and fixing C.P on brass Hand shower (Health faucet) of approved model with Flexible tube with wall hook complete in all respect as per Enginerr in charge. (JAQUAR/ MARC/ ESSCO/ KOHLER/ PARRYWARE or equivalent).(Reference price range Rs.817/-)

NS 55 - Supplying, fitting and fixing C.P on brass Double coat hooks of approved model complete in all respect as per Enginerr in charge. (Jaquar /MARC/ ESSCO/ KOHLER or equivalent).(Reference price range Rs.441/-)

NS 56 - Supplying, fitting and fixing Sanitary fixtures and fittings for Paraplegic Toilet set consisting of as follows.

Wall mounted Closet (Starwhite) viterous china pedestal type ( HINDWARE/ PARRYWARE/ CERA/JAQUAR or equivalent.)(Reference price range Rs.6318/-)

PVC Concealed Cistern (HINDWARE / PARRYWARE/ CERA/JAQUAR) or equivalent.(Reference price range Rs.3464/-)

Wall Mounted Swing-up Bathroom Safety Grab Rail(SS) (JAQUAR/ MARC/ ESSCO/ KOHLER or Equivalent).(Reference price range Rs.14669/-)

Rust Resistant Grab Rail Bar 4 nos. of approved make.(JAQUAR/MARC/ ESSCO/ KOHLER or equivalent).(Reference price range Rs.5924/-)

Bevelled edged mirror of 600 mm x 450 mm size of approved make (MODI FLOAT/ SAINT GOBIN/ ATUL/ GOLDEN FISH or equivalent). (Reference price range Rs.1796/-)

C.P. on brass Toilet paper holder of approved make-(JAQUAR/ MARC/ ESSCO/ KOHLER or equivalent.)(Reference price range Rs.776/-)

C.P. on brass Angular stop cock of approved make-(JAQUAR/ MARC/ESSCO/ KOHLER or equivalent).(Reference price range Rs.487/-)

Soap dish(SS) (EURONICS/ UTEC/KOPAL/ JAQUAR or equivalent ).(Reference price range Rs.586/-)

C.P on brass Towel ring (JAQUAR/ MARC /ESSCO/ KOHLER or equivalent) .(Reference price range Rs.739/-)

C.P on brass Central hole basin mixer without popup waste system without 450 mm long braided hoses, {PARRYWAR / HINDWARE/ CERA/ JAQUARor Equivalent ).(Reference price range Rs.2508/-)

White Vitreous China Wash basin size 630x450 mm with a pair of 15 mm C.P. brass pillar taps of approved make-(PARRYWARE/ HINDWARE/ CERA/ JAQUAR or Equivalent) .(Reference price range Rs.2068/-)

C.P on brass Hand shower (Health faucet) with 8 mm dia, 1.2 metre long Flexible tube with wall hook, (JAQUAR/ MARC/ ESSCO/ KOHLER/ PARRYWARE or equivalent).(Reference price range Rs.817/-)

C.P on brass Two way Bib cock, {JAQUAR/ MARC/ ESSCO/ KOHLER or equivalent).(Reference price range Rs.1031/-)

NS 57 - Providing and fixing white vitreous china flat back half stall star white urinal basin of 580x380x350mm size with with standard flush pipe and C.P. brass spreaders with brass unions and G.I clamps complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required complete in all respect as per Engineer in charge: (PARRYWARE/ HINDWARE/CERA/JAQUAR or equivalent)

NS 57.1 - One urinal basin with urinal valve Auto closing system with in built control cock (PARRYWARE/ HINDWARE/ CERA/ JAQUAR or equivalent).(Reference price range Rs.4748/-)

NS-58 : Providing and fixing CP Brass 32mm size Bottle Trap of approved quality & make and as per the direction of Engineer-in-charge. (CAT NO. MOR-1350, Marc make or equivalent )

NS 59 - Supplying, fitting and fixing Starwhite glazed vitreous Division plates of approved make for urinals of size350(L)X675(W)X130(H) all in mm complete in all respect as per Engineer in charge.(PARRYWARE/ HINDWARE/ CERA/ JAQUAR or equivalent) (Reference price range Rs.1956/-)

NS 60 -Providing and fixing wash basin of approved make with C.I. brackets, without 15 mm C.P. brass pillar taps / basin mixer but with 32 mm C.P. brass waste, 32 mm CP. Bottle trap and unions of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require complete in all respect as per Engineer in charge.

NS 60.1 - White Vitreous China Flat back wash basin (PARRYWARE/ HINDWARE/ CERA/ JAQUAR or equivalent.)(Reference price range Rs.2068/- )

NS 61 - Supplying, fitting and fixing C.P on brass Central hole basin mixer without popup waste system of approved make without 450 mm long braided hoses complete in all respect as per Engineer in charge. {PARRYWARE/ HINDWARE/ CERA/ JAQUAR or equivalent}.(Reference price range Rs.2508/-)

NS 62 -Providing and fixing C.P on brass Towel ring of approved make complete in all respect as per Engineer in charge.(JAQUAR/ MARC/ ESSCO/ KOHLER or equivalent)(Reference price range Rs.739/-)

NS 63 - Providing and fixing C.P brass Towel rails of approved make complete in all respect as per Engineer in charge. (JAQUAR/ MARC/ ESSCO/ KOHLER or equivalent.(Reference price range Rs.994/-)

NS 64 - Providing and fixing stainless steel soap dish of approved make complete in all respect as per Engineer in charge. (EURONICS/ UTEC/ KOPAL/ JAQUAR or equivalent. (Reference price range Rs.585/-)

NS 65 - Providing and fixing C.P on brass manual liquid Soap dispenser of approved make complete in all respect as per Engineer in charge. (Parryware/ EURONICS/ UTEC/ KOPAL/ JAQUAR or equivalent make.(Reference price range Rs.1127/-)

NS 66 - Providing and fixing C.P on brass over head Shower (Over head shower with arm) of approved make complete in all respect as per Engineer in charge (JAQUAR/ MARC/ ESSCO/ KOHLER/ PARRYWARE or equivalent).(Reference price range Rs.862/-)

NS 67 - Providing and fixing CP wall mixer of approved make complete in all respect as per Engineer in charge with provision for overhead shower (JAQUAR/ MARC/ ESSCO/ KOHLER or equivalent).(Reference price range Rs.3737/-)

NS 68 - Supplying, fitting and fixing Storage type Water heater of approved make having inner/outer coated corrosion resistant body, high temperature and pressure safety devices, fixing lugs / bolts etc. and including plug top and electrical power supply 230 volts AC, single phase, 6 KW wattage with ISI Certification & necessary fixtures all complete in operational. Storage capacity of 300 Litres set of approved make with accessories Storage Water Heater complete in all respects as per direction of the Engineer in charge. (RACOLD/ VENUS/ USHA LEXUS/ BAJAJ/ CROMPTON GREAVES/ AO SMITH (JAQUAR or Equivalent)(Reference price range Rs.58474/-)

NS 69 - Providing and fixing 450mm long braded hose of approved make with two 15 mm nuts & rubber washers without nipple complete with C.P. brass flange including cutting and making good the walls wherever required complete in all respects as per engineer in charge. ( JAQUAR/ MARC/ ESSCO/ KOHLER or equivalent)(Reference price range Rs.212/-)

NS 70 - Providing and fixing S.S. round grating of approved make with round frame, minimum 125 mm Dia overall size, glossy finish including setting in floor with sealent complete in all respects as per engineer in charge.( GRT-0012 SS Grating Round Frame with Waste Pipe Hole and Locking Mechanism (Hole Pattern) 125mm or approved equivalent)(Reference price range Rs.455/-)

NS 71 - Providing, fixing and testing UPVC soil waste and vent pipes of approved make UV stabilize and conforming to IS: 13592 - Type-B including all fittings conforming to IS:14735 such as W.C. connector, bends, junctions, inspection doors, offsets, vent cowls, access pieces/plugs, cleanout plugs etc. clamps/ structural steel supports as required/directed at site, jointing with rubber ring and rubber lubricant including cutting holes in walls and making good the same complete in all respect as per Engineer in charge.

a) 110 mm dia

NS 72 - Providing & laying, in trenches or in exposed, of uPVC pipes with fittings of class III (6 kg/ cm2) as per IS:4985 and as per specification with rubber ring and rubber lubricant,(EPDM/SBR) for all depths with or without well graded granular bedding (Type-E) for pipe length as per drawing and specification including hydraulic field testing and commissioning etc all complete as directed by Engineer

a) 63 mm dia

b) 50mm dia

c ) 40 mm dia

NS 73 - Providing and fixing UPVC trap ('P' or 'S') of self cleaning design without C.P. grating with or without vent horn complete, as shown in detailed drawing including inlet fitting wherever required including cost of cutting and making good the walls & floors.

a) 110 mm inlet and 110 mm outlet

WATER SUPPLY

NS 74 - Providing, fixing, Chlorinated polyvinyl chloride (CPVC) pipes SDR11 , having thermal stability for hot and cold water supply, including all CPVC plain and brass threaded fittings, including fixing the pipe with clamps at 1m spacing . This includes jointing of pipes and fittings with one step CPVC solvent cement and cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer-in-charge.

Concealed work including cutting chases and making good the wall etc.

a) 40mm nominal outer dia. Pipes

b) 50mm nominal outer dia. Pipes

NS 75 - Providing, fixing, Chlorinated polyvinyl chloride (CPVC) pipes SDR 11/sch40 , having thermal stability for hot and cold water supply, including all CPVC plain and brass threaded fittings, including fixing the pipe with clamps at 1m spacing . This includes jointing of pipes and fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer-in-charge.

a) 65mm dia. nominal inner dia.

b) 80mm dia. nominal inner dia.

c) 100mm dia. nominal inner dia.

NS 76 - Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) :

a) 100mm nominal bore

NS 77 -Providing and fixing butterfly valves of PN 1.0 rating, wafer type, C.I. body I.S. 210 FG 220, disc: C.F.8/SS304, shaft AISI 410, seat ntegrally moulded Nitrile/EPDM of approved make, handle lever with on /off indication all complete as required.

a) 100mm dia

NS 78 - Providing and fixing 2/2 Way Pilot Operated Diaphragm type Solenoid Valve, screwed or flanged end,suitable for water supply as per site, of SS body (SS-304) to ASTM A 351 GR CF 8 & internals having weather proof coil enclosure & working pressure range (min. 0.7 Kg/cm2 & max 12 Kg/cm2 ) with coil of 220 Volt, AC suitable for horizontal installation, normally closed with all electro mechanical accessories including 2/2 way Y type strainer at inlet of solenoid valve, screwed ends, body & cover SS 304 to ASTM A 351 GR CF 8 with same working pressure as stated above, having diaphragm of nitrile rubber and 40 mm mesh size. along with automatic solenoid valve On-Off Controller Box with one number Float switch sensor for water tank level controller with five meter long control wire connecting to solenoid valve and exluding electrical supply wire connection to controller box and wire from controller box to solenoid valve, with opeating voltage of 220 AC suitable for vertical/horizontal installation in water tank as per site condition suitably connected to solenoid valve through control cable all inclusive with all electro mechanical accessories complete operational (Operation by SCADA system).

a) 25 mm dia

NS 79 - Providing and fixing ball valve (brass) of approved quality, High or low pressure, with plastic floats complete

a) 40mm nominal bore

NS -80 Providing and fixing gun metal non- return valve of approved quality (screwed end) :

a) 20 mm nominal bore- Horizontal

b) 100 mm nominal bore- Horizontal

NS 81 - Constructing masonry Chamber 30x30x50 cm inside, in brick work in cement mortar 1:4 (1 cement :4 coarse sand) for stop cock, with C. I. surface box 100x100 x75 mm (inside) with hinged cover fixed in cement concrete slab 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size), i/c necessary excavation, foundation concrete 1:5:10 ( 1 cement : 5 fine sand : 10 graded stone aggregate 40mm nominal size ) and inside plastering with cement mortar 1:3 (1 cement : 3 coarse sand) 12mm thick, finished with a floating coat of neat cement providing and fixing painted CI frame and cover of size 300X300 weighing not less than 7.2Kgs with locking arrangement fixing the frame in CC 1:2:4 including form work, curing, etc complete as per standard desig

NS 81.1 - With common burnt clay F.P.S.(non modular) bricks of class designation 7.5

RAIN WATER PIPES AND FITTING

NS 82 - Providing and fixing 50 mm dia CPVC Spout of length upto 300 mm, including concreting and water proofing around it.

EXTERNAL PLUMBING

WATER SUPPLY

NS 83 - Providing and fixing G.I. pipes (C- Heavy) complete with G.I. fittings including trenching and refilling etc. conforming to IS : 1239.

a) 40 mm nominal bore.

b) 50 mm nominal bore.

NS 84 - Providing, fixing, testing & commissioning screwed type Cast Steel compact Pressure reducing valve of approved quality conforming to IS-9739 with pipes and specials including making necessary screwed/ flanged joints by providing all jointing materials including painting and testing the joints to hydraulic pressures specified for pipes all complete as per drawings and as directed by the Engineer-in-Charge to manage pressure of water, to restrict hydraulic forces by spring forces and maintains the desired pressure level in various parts of circuit. The maximum inlet pressure should be 20 Kg/Sqcm & outlet pressure 8-12 Kg/Sqcm.

a) 40 mm nominal bore.

NS 85 - Providing and fixing Water Level Monitor (Water Gauge) for installing on the over head Water Reservoir consisting of calibrated back ground board, copper float valve, strand red wire, required number of pulleys, puddle collar / sleeves as required adjustable pointer etc. complete operational.(Water level difference upto 4 m.) - For over head reservoir

NS 86- Providing and fixing water level control switch assembly consisting of adjustable low level and high level actuation for auto on/off the respective motor for installing from top / side of the reservoir through sleeve of 150 mm dia on top / side of underground reservoir including flange, PVC guide tube, two numbers floats with SS wire and electric contactor including cost of control wiring from the respective motor panel to the controlling switch etc. complete operational & as directed by the Engineer-in Charge.

NS-87: Supply, installation, testing and commissioning XYLEM/ KIRLOSKAR / KSB / GRUNDFOSS / WILO / JHONSON make complete factory assembled Single pump booster system comprising of Pump motor set along with starter Control panel for auto operation, 60lit Pressure Tank to be supplied by the pump manufacturer (located on roof top for lifting / forcing water to Hot water Tank & to Hot water & Cold water to Fixure Points of Varrious floors to end use point/network as stated below & of required drive (Motor HP), having discharge capacity and pumping head with common base frame all electrical accessories, with over load protection, relay, including other accessories like ball valve , butterfly valve , NRV (recommended by manufacturer) etc., coupling of required size on suction end flexible removable type (Flanged) coupling on delivery end of pump, required M.S. galvanized supporting frame complete operational:

NS-87.1 Pressure Pump 160 lpm pressure 2.5 kg/sqcm (25m head)with starter control panel,relay panel for auto operation. Stainless steel impeller Wetted parts made up of stainless steel with pneumatic tank & electronic control for automatic operation High efficient motor suitable for wide voltage fluctuations.

NS-87.2Recirculation Pump 80 lpm. pressure 1.0 Kg/sqcm (10m head) with starter Control panel,Relay panel for auto operation.

(ELECTRICAL WORKS)

LIGHT FITTINGS (SURFACE/ RECESS MOUNTED)

Supply, installation, testing & commissioning of the following light fixtures complete with lamps, led driver, electronic ballast etc complete in all respect .Supply including all accessories required for mounting at surface/ recess /wall as required conforming to relevant IS codes.

NS-88-Supply, installation, testing & commissioning of 1x18W LED TUBELIGHT( 4 feet), Opal diffuser, Polycarbonate housing with Polycarbonate end caps, High efficiency long life SMD LED module with system lumen efficacy of 100 lm/W. Powered by a integral electronic driver (SMPS based constant current supply) with Output Short-Circuit Protection, Surge Voltage Protection greater than 2 kV. System Lumen 4400. CRI >80, IP 20 , Color temperature 5700K to 6500K, THD <20% and PF >0.95, Life class of 50,000 hrs @ L70, Operating Temperature:-10 TO +45 DEG.C; Input Supply Voltage Range:140-270 V, Frequency :50-60 HZ; Internal Surge Protection:4 KV; Protection. DRIVER SAFETY REQUIREMENT STANDARDS :IS 15885-2-13, TEST REPORT TO BE SUBMITTED; PHOTO BIOLOGICAL SAFETY NORMS: IS 16108, TEST CERTIFICATE TO BE SUBMITTED; CERTIFICATION: LM 79 FOR LUMINAIRE LM 80 FOR LED SOURCE similar to Havells Cat. No. Regal Battern with 1x18W Photon Ultra Tubelight or equivalent.

NS-89-Supply, installation, testing & commissioning of 2x18W LED TUBELIGHT( 4 feet) suitable for G13 holder with single side connection, Opal diffuser for glare free operation. Polycarbonate housing with Polycarbonate end caps.High efficiency long life SMD LED module with system lumen efficacy of 100 lm/W. Powered by a integral electronic driver (SMPS based constant current supply) with Output Short-Circuit Protection, Surge Voltage Protection upto 4kV. System Lumen 4400. CRI >80, IP 20 , Color temperature 5700K-6500K, THD <20% and PF >0.95, Life class of 50,000 hrs @ L70, Operating Temperature:-10 TO +45 DEG.C; Input Supply Voltage Range:140-270 V, Frequency :50-60 HZ; Internal Surge Protection:4 KV; Protection. DRIVER SAFETY REQUIREMENT STANDARDS :IS 15885-2-13, TEST REPORT TO BE SUBMITTED; PHOTO BIOLOGICAL SAFETY NORMS: IS 16108, TEST CERTIFICATE TO BE SUBMITTED; CERTIFICATION: LM 79 FOR LUMINAIRE LM 80 FOR LED SOURCE similar to Havells Cat. No. Regal Battern with 2x18W Photon Ultra Tubelight or equivalent.

NS-90-Supply, installation, testing & commissioning of Wall mounted Night lamp with shade complete with all accessories. Havells Cat. Floretine WL 1LS B22 SS PPCP or equivalent

NS-91-Supply, installation, testing & commissioning of 12W Led Slim surface mounted round LED panel al. die cast body with diffuser, Color temperature 4000K, similar to Havells Cat. No. LHEAAVP6IL1W012 or equivalent.

NS-92-Supply, installation, testing & commissioningof 300mm sweep 1 phase Exhaust fan Havells Cat. No. Ventil Air-DB 300 or equivalent of approved make with heavy duty louvers shutter, complete with frame, as required and including all other fixing accessories as required.

NS-93-Supply, installation, testing & commissioning of 15W Led surface mounted round LED panel, CRI>80, Color temperature 5700K-6500K, THD<10%,PF>0.95, IP20, IK03, Life class of 50,000 hrs @ L70,Operating Temperature:-10 To +45 DEG.C; Input Supply Voltage Range:140-270 V, Frequency : 50-60 HZ,Internal Surge Protection:2.5 KV; similar to Havells Cat. No. Integra Surface 15W or equivalent.

NS-94-Supply, installation, testing & commissioning of 10W Surface mounted, IP 65, bulk head LED luminaire, CRI>80, Color temperature 5700K-6500K, THD<10%,PF>0.95, IK03, Life class of 50,000 hrs @ L70,Operating Temperature:-10 TO +45 DEG.C; Input Supply Voltage Range:140-270 V, Frequency : 50-60 HZ,Internal Surge Protection:2.5 KV; similar to Havells Cat. No.Hexa 10W or equivalent.

NS-95-Supply, installation, testing & commissioning of Wall mounted 9W Led Mirror light, CRI>80, Color temperature 5700K-6500K, THD<10%,PF>0.95, IP20,IK03,Life class of 50,000 hrs @ L70,Operating Temperature:-10 To +45 DEG.C; Input Supply Voltage Range:140-270 V, Frequency :50-60 HZ,Internal Surge Protection:2.5 KV; similar to Havells Cat. No. Lumiline 9W or equivalent.

NS-96-Supplying and fixing 2(+1) Module Weatherproof cabinet -IP65 (Legrand Cat no.601932) along with all accessories on surface/ recess along with 40A, 240 V "C" curve DP MCB complete with connections, testing and commissioning etc. as required.( Geyser at Roof)

CABLES

NS-97 - Supply of following siz of 1.1KV grade multicore aluminium conductor XLPE insulated and PVC shethed armoured cable as per IS 7098:1988 with up to date amendment

a) 4.0 C x 16 sqmm

b) 3.5 Core x 25 sq.mm

c) 3.5 Core x 35 sq.mm

d) 3.5 Core x 50 sq.mm

e) 3.5 C x 120 sqmm

f) 3.5 C x 240 sqmm

NS-98 -Supply and fixing of following size of 1.1KV grade multicore copper conductor XLPE insulated and PVC shethed armoured cable on surface/trench/cable tray/pipe etc as required as per IS 7098:1988 with up to date amendment

a) 4C x 6 Sq. mm

b) 3C x 2.5 Sq. mm

MAIN PANEL & DISTRIBUTION BOARD

NS-99 - Main Panel (Student Hostel-II)

Incoming - 1 no. (comprising of)

1 No.- 630A 4P, MCCB as incomer

2 Set - Single core CTs 630/5A of 15 VA burden and accuracy Class - 1.

1 Set - R,Y,B Phase indication LED lamp with 2 Amp back up HRC fuse.

BUSBARS

800A Aluminium busbars, including making necessary connections.

Outgoing

5Nos.- 400A, FP MCCB

2Nos.- 100A, FP MCCB

2 Nos.- 63A, FP MCCB

NS 100 - SUB MAIN PANEL ( BLOCK- A,B & C) (Student Hostel-II)

Incoming - 1 no. (comprising of)

1 No.- 400A 4P, MCCB as incomer

2 Set - Single core CTs 400/5A of 15 VA burden and accuracy Class - 1.

1 Set - R,Y,B Phase indication LED lamp with 2 Amp back up HRC fuse.

BUSBARS

400A Aluminium busbars, including making necessary connections.

Outgoing

6Nos.- 100A, FP MCCB

2Nos.- 40A, FP MCB

NS 101- FLOOR MAIN DB (Student Hostel-II)

Incoming - 1 no. (comprising of)

1 No.- 100A 4P, MCCB as incomer

1 Set - R,Y,B Phase indication LED lamp with 2 Amp back up HRC fuse.

BUSBARS

100A Aluminium busbars, including making necessary connections.

Outgoing

8Nos.- 40A, FP MCB

NS 102 - MAIN POWER DB (GEYSER) (Student Hostel-II)

Incoming - 1 no. (comprising of)

1 No.- 100A 4P, MCCB as incomer

1 Set - R,Y,B Phase indication LED lamp with 2 Amp back up HRC fuse.

BUSBARS

100A Aluminium busbars, including making necessary connections.

3nos.63 Amps. Rating, 2pole RCCB, 30mA

Outgoing

9Nos.- 40A, DP MCB

NS 103 - Emergency Main Panel (Student Hostel-II)

Incoming - 1 nos. (comprising of)

1 No.- 200A 4P, MCCB 25KA with thermal magnetic release

1Set - 200/5A CL-1.0, 15 VA

1 Set - R,Y,B Phase indication LED lamp with 2 Amp back up HRC fuse.

BUSBARS

200A Aluminium busbars, including making necessary connections.

Outgoing

5 Nos.- 100A, FP MCCB 25KA with thermal magnetic release

2Nos.- 63A, FP MCCB 25 kA with thermal magnetic release

NS 104 - Emergency SUB MAIN PANEL ( BLOCK- A,B & C) (Student Hostel-II)

Incoming - 1 nos. (comprising of)

1 No.- 100A 4P, MCCB 25KA with thermal magnetic release

1Set - 200/5A CL-1.0, 15 VA

1 Set - R,Y,B Phase indication LED lamp with 2 Amp back up HRC fuse.

BUSBARS

100A Aluminium busbars, including making necessary connections.

Outgoing

5 Nos.- 63A, FP MCCB 25KA with thermal magnetic release

3Nos.- 40A, FP MCCB 10KA with thermal magnetic release

NS 105 - Emergency FLOOR MAIN DB (Student Hostel-II)

Incoming - 1 nos. (comprising of)

1 No.- 63A 4P, MCCB 25KA with thermal magnetic release

1 Set - R,Y,B Phase indication LED lamp with 2 Amp back up HRC fuse.

BUSBARS

63A Aluminium busbars, including making necessary connections.

Outgoing

4Nos.- 40A, FP MCB 10KA

2Nos.- 40A, DP MCB 10KA

NS 106 - Lift-2

Supplying, installation, testing and commissioning of Capacity 1020 kgs, 15 persons with followings specifications.

SPEED (mps) : 1 mps

RISE (m): 16 m

STOPS : 6 Stops With (Center opening)

CONTROLLER TYPE : ACD3-MR of Otis or equiv.

DRIVE : VF Regenerative (Closed Loop)

POWER SUPPLY : 400/415 Volts (3 Phase AC)

OPERATION : Full collective operation

CAR GROUP : One car

MACHINE : PM Gearless (Located above shaft)

TRACTION MEDIA : Flat Coated Steel Belt

CAR FINISH :  Rear Mid Panel = Stainless Steel  Rear Corner Panels = Stainless Steel  Side Panels = Stainless Steel  Front Panels = Stainless Steel

FALSE CEILING TYPE : CD-41 of Otis or equiv.

FALSE CEILING FINISH : Stainless Steel

VENTILLATION : Cross flow fan

HAND RAILS : Stainless Steel Mirror Finish Handrails on all car panels(sideLH,sideRH&Rear)

FLOORING : Vinyl Tiles

CAR DOOR FINISH : Stainless Steel

LANDING DOORS FINISH : Stainless Steel

FIRE RATED DOORS : Fire rating-60mins

CAR & HOISTWAY DOOR TYPE : Center opening

DOOR OPERATOR : DC Door Operator

COP ; COP for stops <= 12 (950mm) in Stainless Steel #4(Hairline)

CAR POSITION INDICATOR : Required.

HALL BUTTON ARRANGEMENT : Hall Button with HPI

STANDARD FEATURES : Anti-nuisance Car Call Protection Overload Device Nudging, Emergency Firemen’s Service Emergency Car Light Unit Infrared Curtain Door Protection Door Time Protection, Emergency Alarm Button Extra Door Time of Lobby & Parking Door Open/Close Button Manual Rescue Operation Belt Inspection Drive Auto Fan Cut Off

OPTIONS INCLUDED : Automatic Rescue operation, Voice Synthesizer, Intercom, Provision for CCTV and any other proprietary feature.

Above Lift

FIRE ALARM AND DETECTION SYSTEM

Fire Alarm and Detection

NS 107- Supply, Installation, Testing, Commissioning of Fiber optic communication interface card for FDA panel along with trans -receiver module enclosed.

PA SYSTEM

IP BASED TELEPHONE SYSTEM

NS 108- Supply, Installation, Testing and Commissioning of SIP based 2-way IP Deskphone supporting Monochrome 128x32 pixel display and three context-sensitive soft keys. It should be POE Class-1 device.

Networking

Local Area Network

NS-109 - Supply, Installation, Testing and Commissioningof 24 x 1GbE PoE+ RJ45 ports and minimum Four 10GbE SFP+ Slots fully loaded, 370 W PoE Budget. Maximum PoE Class 3 ports (15.4 W per port) = 24 and Maximum PoE+ Class 4 Ports (30 W per Port) = 12 PortS. Stacking Bandwidth : 80 GbgS Or more, Switch Bandwidth: 130 Gpbs or More, Forwarding Capacity: 90 MbpS or more, Layer 3 Support.

NS-110 - Supply, Installation, Testing and Commissioning of 8 x 1 GbE PoE+ RJ45 ports and minimum two 10GbE SFP+ Slots fully loaded, 90W POE Budget

NS-111 - SITC of Indoor access points, Wireless Standard IEEE 802.11 a/b/g/n/ac/ax, Radios, 5 GHz: 802.11 a/n/ac/ax, 4x4 and 2.4 GHz: 802.11 b/g/n/ax, 2x2, Data rate @ 4x4, 5 GHz @ 2400 Mbps and 2.4 Ghz @ 573Mbps.

NS-112 - Supply, Installation, Testing and Commissioning of Outdoor access point wifi standard EEE 802.11 a/b/g/n/ac/ax, Data Rate 5GHz Radio 1200 Mbps 2.4Ghz radio 573Mbps, 5Ghz 802.11a/b/g/n/ac/ax,2x2, 2.4 GHz 802.11a/b/g/n/ac/ax,2x2

NS-113 - Supply, Installation, Testing and Commissioning of UPS with 2 KVA capacity for power backup of 30 Minutes with external battery of 12 V, 18 AH complete etc. as required.

NS-114 - Supply, Laying, testing and commissioning of CAT 6A U/UTP Cable 23 AWG , LSZH, UL Certified , performance requirement as per as per ANSI/TIA 568C.2, Yellow RAL 1018.

NS-115 - Supply, installation, testing and commissioning of CAT6A UTP 24 port loaded patch panel made up of galvanised steel sheet, Compliant with standards: ISO/IEC 11801 Edition 3.0 Contacts: gold/nickel, thickness of gold > 0.8 μm minimum ,Equipped with rear cable guide to hold cable during maintenance,The connectors are connected from the front without a special tool. Equipped with 4 cassettes of 6 RJ45 Cat. 6A connectors with toolless fast connection, Each connector can be removed individually, marked 568 A/B, Max. number of connections and disconnections: 5 without replacing the wire, Endurance: 2500 operations (plug-in/pull-out).

NS-116- Supply, installation, testing and commissioning of CAT 6A UTP 1 MTR factory made or factory crimpped LSZH Patch cord Green colour.

NS-117 - Supply, installation, testing and commissioning of CAT 6A UTP 2 MTR factory made or factory crimpped LSZH Patch cord Green colour.

NS-118- Supply, installation, testing and commissioning of Cat 6A UTP RJ 45 Sockets Tool Less Crimping, as per- ISO/IEC 11801 Edition 2; should have transparent shutter for protection against dust, Contacts :gold/nickel, minimum thickness of gold > 0.8 μm , Body made of high impact PBT Polycarbonate plastic material, Endurance 2500 movements (plug insertion / withdrawal). IK03, Maximum no of Connections/ Re connections 5 without refreshing the wiring.

NS-119 - Supplying installation testing and commissioning of Single Port Face Plate 1 Module in white colour.

NS-120 - Supply, installation, testing and commissioning of Two Module Metal Surface box.

NS-121 - Supply, installation, testing and commissioning of 6 port Rack mount Sliding Metal 19" Fibre optic drawer (LIU) with trasperent cover, 4 cable entries, supplied with screw fixing kit, 4 cable glands (Ø 13.5 and 16 mm), coiling system, Sliding end stop at a 30° angle for easier wiring with lock with lock. Depth: 220 mm, height 1 U consist of MM SC Adapter, MM SC Pigtail 1 Mtr, Splice tray and blanking plate.

NS-122- Supplying installation testing and commissioning of Single Mode SC-LC Duplex Patch Cord, 2 Mtr.

NS 123- Supply, installation, testing and commissioning of 12U, 600 (W) x 500(D) Wall Mount Rack with 2 Nos of Fan, 1 Metal Cable Manager, 1 No 6 amp 6 Socket PDU and mounting hardware packet.

IP BASE CLOSED-CIRCUIT TELEVISION [CCTV]

NS 124- Supply, Installation, Testing & Commissioning of Indoor Network Dome Camera, 120 dB Wide Dynamic Range, 3 IR LEDs with atleast 20 Metre IR Range, 1/2.7" Sensor, 2 MP Resolution, Focal Length of 2.7-12 mm, PoE, H.264,Triple Stream,Onvif S&G,UL(provision for 128 GB cards ).

FIRE FIGHTING WORKS

HYDRANT SYSTEM - PIPING WITH ACCESSORIES

NS 125- Providing, fixing, testing & commissioning of SS spring loaded air relief valve for pressure of 16 kg/sqm of approved quality with SS isolation valve, tapers, G.I. pipes and specials etc. including making necessary screwed/ flanged joints by providing all jointing materials including painting and testing the joints to hydraulic pressures specified for pipes all complete as per drawings and as directed by the Engineer-in-Charge.

a) 25 mm dia

NS 126 - Providing and fixing Cast Carbon Steel / forged brass CS Ball valve (Hyd. Test pressure body 30 kg/cm2 & seat 21 kg/cm2) of the following size: (Cost inclusive of providing necessary union / flange connection).

a) 50 mm dia

NS 127 - Providing & fixing indoor type hose lockable cabinet frames fabricated from 40 x 40 x 5 angle iron sections and 16 gauge MS sheet with full front glass door and locking arrangement, suitable to accommodate landing valves, 15 m long hoses, first-aid hose reel and branch pipe nozzle & fire mans’ axe. The cabinet frame shall be painted with one coat of primer and two or more coats of synthetic enamel paint of approved make and shade, as required (Approx 2.1 m (high) x 0.9 m (wide) ). The item shall be complete of MS housing with front door. (Cost shall be inclusive of providing break glass box containing key for the cabinet along with hammer).

NS-128 - Supply and fixing of FIRE HOSE BOX (Wall mounted) made of MS 16-SWG with 3mm glassed door having size: 750x600x250mm to accommodate 2-nos. of 15 Mtr hose pipe with male & female coupling & 1 No. Universal Nozzle.

NS 129- Providing and fixing standard firemans axe with heavy rubber handle.

NS-130 - Supply, Installation, Testing and Commissioning of Electrical Control Panel in common cubicle with suitable compatmentation for Booster Pumps as per requirment of the drives and with auto on/off logic and operational sequence as per specifications with all meterial, accessories, instrumentation etc.complete.( GA drawing including circuit diagram shall be submitted by the contractor and to be approved by the Owner/consultant before fabrication of the control panel). Note : Cost shall be inclusive for approval of fire hydrant & sprinkler system from local fire authority and Fire Emergency services and any other relevant statutory authority at initial & various other stages of works, including preparation of report / drawings as per fire authority. Contractor shall include cost of all liaison works which are not explicitly mentioned above but are mandatory to have fire authority approval (any statutory charges will be reimbursed as per actual upon production of the invoice / challan informer of the owner..

NS 131-Providing & fixing 150 mm dial type Pressure gauge of (0-16kg/cm2) range with gun metal shut off cock etc. duly calibrated before installation in MKS and FPS units and fixing the same where required as directed including all fittings, short piece, nipples, elbows testing the joints etc.all complete. (Quantity of this item will be payable only where it has not been included in the relevant composite items).

PORTABLE CHEMICAL FIRE EXTINGUISHERS

Supply, installation, testing and commissioning of following types of Extinguishers with provision of wall bracket (fixed with anchor fastner).

NS 132 - 9 ltr. Water type stored pressure Fire Extinguisher filled with water of TDS 3 to 4 PPM, Applicable fire class A, UTGS Pressure Gauge, Gross Weight 12 Kg, empty weight 4.3 Kg, Can Height 575mm, Diameter 180 ± 10mm, Discharge Time 35 Sec, Controllable discharge mechanism, Jet Range 7 Meters, Average Discharge is 95%, applicable on Class A, Fire Rating- 2A, Can Construction : Deep drawn & CO2 Mig welded, Brass forged valve with safety Pin is of SS material, Controllable discharge mechanism with EPDM Hose & Nozzle, Internal Coating – Plastic Lining, External Coating - Pure Polyester Powder coating (UV Resistant), Sheet metal thickness : 2mm, construction as per IS 15683:2006 and ISI Marked.

NS 133 - 4.5 kg CO2 High Pressure Portable Fire Extinguisher, filled with Co2 Gas as per IS 15222, Gross Weight 16.4, empty weight 11.9 Kg, Control discharge mechanism fitted with 1 Meter Wire Braided Hose & Flat Horn with Diffuser Nozzle for dispersed discharge of CO2, Discharge Time 12 Sec, Average Discharge is 95%, Applicable on Class B, C and electrically started Fire, Fire Rating 21B, Internal coating is not applicable & External coating is of enamel spray painting, Powder Coated Handle, Valve Confirm to IS 3224 ISI Marked, CO2 Cylinder construction: hot spinning by seamless pipes & bearing ISI mark, Body confirms to IS 7285 and PESO APPROVED, Extinguishers confirmed to IS 15683:2006 and ISI marked.

NS 134 - ABC Type Fire Extinguisher Cap. 4 kg Filled with Mono Ammonium Phosphate Powder 90% confirms to IS 14609, Stored Pressure Type, UGTS Pressure Gauge, Gross Weight 8.9 Kg, Empty Weight 2.9 Kg, Can Height 530 mm, Diameter 150 ± 10mm, Discharge Time 24 Sec, Controllable discharge mechanism, Jet Range 5 Meters, Average Discharge is 90%, applicable on Class A,B & C and electrically started Fire, A Rating- 3A, B Rating 21B, Can Construction : Deep drawn & CO2 Mig welded, EPDM Rubber Hose with both end Aluminum clamped, Internal Coating - Epoxy Powder coating, External Coating - Pure Polyester Powder coating (UV Resistant), Brass forged valves with safety Pin is of SS material, Sheet metal thickness : 1.8 mm, ISI Approved IS 15683:2006.

Bidder Name

Amount

SOM PROJECTS PVT LTD(GSTN-07AAJCS9451K1ZR)

GANESH TAMULI ENGINEERING PRIVATE LIMITED(GSTN-18AACCG9504C1ZU)

Meetei Construction Pvt.Ltd(GSTN-14AAJCM8332K1Z8)

Bavin Deren Marbaniang(GSTN-NA)

SPS INFRABUILD PVT LTD(GSTN-NA)

Bidder Name

Amount

SOM PROJECTS PVT LTD(GSTN-07AAJCS9451K1ZR)

GANESH TAMULI ENGINEERING PRIVATE LIMITED(GSTN-18AACCG9504C1ZU)

Meetei Construction Pvt.Ltd(GSTN-14AAJCM8332K1Z8)

Bavin Deren Marbaniang(GSTN-NA)

SPS INFRABUILD PVT LTD(GSTN-NA)

Bidder Name

Amount

SOM PROJECTS PVT LTD(GSTN-07AAJCS9451K1ZR)

GANESH TAMULI ENGINEERING PRIVATE LIMITED(GSTN-18AACCG9504C1ZU)

Meetei Construction Pvt.Ltd(GSTN-14AAJCM8332K1Z8)

Bavin Deren Marbaniang(GSTN-NA)

SPS INFRABUILD PVT LTD(GSTN-NA)

GANESH TAMULI ENGINEERING PRIVATE LIMITED

Bavin Deren Marbaniang

SPS INFRABUILD PVT LTD

SOM PROJECTS PVT LTD

GANESH TAMULI ENGINEERING PRIVATE LIMITED

Bavin Deren Marbaniang

SPS INFRABUILD PVT LTD

SOM PROJECTS PVT LTD

GANESH TAMULI ENGINEERING PRIVATE LIMITED

Meetei Construction Pvt.Ltd

Bavin Deren Marbaniang

SOM PROJECTS PVT LTD

GANESH TAMULI ENGINEERING PRIVATE LIMITED

SOM PROJECTS PVT LTD

Bavin Deren Marbaniang

SPS INFRABUILD PVT LTD

Bavin Deren Marbaniang

Meetei Construction Pvt.Ltd

SOM PROJECTS PVT LTD

SPS INFRABUILD PVT LTD

Bavin Deren Marbaniang

Meetei Construction Pvt.Ltd

SPS INFRABUILD PVT LTD

SOM PROJECTS PVT LTD