REPAIR MAINT OF DRAIN, COMPOUND WALL, FOOTPATH, ETC IN AREA II UNDER GE SAUGOR

Amount

Excavation in trenches not exc 1.5m wide, not exc 1.5 m deep in soft/ loose soil for foundation, shaft, wells, manholes, etc not exc 10 Sqm on plan and not exc 1.5 m in depth and getting out complete all as specified and directed.

M&L for coloured designer tiles exterior grade ( ENDURA or equivalent make as approved by GE ) 12 mm thick laid over and including 15mm thick cement mortor 1:6 set and jointed in floor and pointed in neat cement slurry with grey cement and pigment including dismantling of floor, hearth or wall tiles / terrazo including cement mortar bedding (but not backing),removal servicable tiles from site and rubbish off the premises complete all as specified and directed.

Removing excavated soil not exceeding 50 m distance and depositing where directed at a level not exc 1.5 metre above the starting point complete all as specified and directed.

Returning, filling in, including spreading, levelling, watering & well ramming in layers not exc 25cm thick in soft/loose soil complete all as specified and directed..

M&L for RCC design mix M25 (using 20 mm graded stone aggregates) as in foundations, including rafts, footings, foundation beams, plinth beams including demolition of reinforced cement concrete of any description and in any position complete all as specified and directed.

M&L for RCC design mix M25 (using 20 mm graded stone aggregates) as in columns, pillars, piers, posts and struts including demolition of reinforced cement concrete of any description and in any position complete all as specified and directed

M&L for formwork to sides of concrete foundations, footings, bases of columns, raft & raft beams, sides & soffits of foundation & plinth beams; and similar work; verticle or to batter rough finished surfaces of concrete flat complete all as specified and directed.

M&L for formwork to sides of pillars, posts, struts, piers,columns, and stanchions rough finished surfaces of concrete square, rectangular or polygonal complete all as specified and directed..

Demolition of cement concrete in ground floors and pavings not exc 15cm thick below or above ground floor complete all as specified and directed.

M&L for moorum/red bajri filling in floors or pavings laid in layers not exc 15cm thick spread levelled and compacted with mechanical earth compactor including watering complete all as specified and directed.

M&L for cement concrete 1:4:8, type D 2 (using 40 mm graded stone aggregates) as in foundations, filling and mass concrete complete all as specified and directed.

M&L for brickwork with subclass 'B' old size bricks, straright or curved on plan exc 6m mean radius built in cement mortar 1:6 including demolition of brick work with all qoins arches , pillars etc built in cement mortar complete all as specified and directed

All as per Srl item No. 12 as above but except bricks Note:-Serviceable bricks obtained from demolition shall be re-used in this item

M&L for providing precast cement concrete louvers and jallies 35 mm thick, type B-0, 1:2:4 (using 12.5 mm graded stone aggregates) set in cement mortar (1:4), (measured solid), including all mouldings including dismantling of existing jallies of any description complete all as specified and directed..

M&L for preparing the new plastered surfaces and applying three coats of white wash on walls complete all as specified and directed.

M&L for mild steel TMT bars 10 mm dia and over cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

M&L for mild steel TMT bars 5mm dia & over upto & including 10mm dia in stirrups, spacers & binders, cut to length, bent to shape required, binding with & including mild steel wire (annealed) not less than 0.9mmdia or securing with clips complete all as specified and directed..

M&L for rendering 15mm thick cement plaster in cement mortar 1:4 on brick wall / concrete surfaces of finishing the surfaces even and smooth without using extra cement complete all as specified and directed.

M&L for PCC type C-2, 1:3:6 (using 40mm graded stone aggregates) as in foundation, filling and mass concrete complete all as specified and directed.

M&L for walling of random rubble, brought up to course well bounded bedded and solidly hearted built in CM(1:4) including demolition of rubbled stone masonry including all qoins arches, pillars, etc built in cement mortar complete all as specified and directed

All as per Srl item No 20 as above but except stone Note:-Serviceable stones obtained from demolition shall be re-used in this item

M&L for PCC (1:3:6), type C1 (using 20mm graded stone aggregates) as in coping and the like including weathering , slightly rounded or chamfered angle with and incl necessary use and waste of form work complete all as specified and directed. .

M&L for 18mm to 20mm thick Granite slab of any shade ( table rubbed and polished ) in steps, jambs, pillars, windowcills, cooking plateforms, wall and like in cement mortor 1:4 including pointing in white cement 1:2 using pigment to match shade of the slabs including dismantling of floor, hearth or wall tiles / terrazo including cement mortar bedding (but not backing),removal servicable tiles from site and rubbish off the premises complete all as specified and directed.

M&L for rounding/ chamferring to edges of stone slabss one edge , such as in steps , cooking plateform and other similar situations complete all as specified and directed.

M&L for rendering 15mm thick in CM (1:4) on random rubble stone masonry complete all as specified and directed.

M&L for PCC (1:2:4), type B1 (using 20mm graded stone aggregates) as in benching of drain complete all as specified and directed.

M&L for extra for forming fair finished drain or channel 30 cm inner girth in cement concrete using extra cement including forms moulds, mitered /stopped ends complete all as specified and directed.

Add or deduct for each 25mm girth or part there of over or under 30 cm complete all as specified and directed.

M&L for precast RCC 1:1.5:3, type A-1 (using 20 mm graded stone aggregates) as in drain cover with plain fair faces including chambers, wathering, throating etc and setting in CM (1:4) including demolition of RCC in precast cover slab any thicknes (reinforced) complete all as specified and directed.

M&L for 75mm thick PCC (1:4:8), type D-2 (using 40mm graded stone aggregates) as in sub base complete all as specified and directed.

M&L for machine pressed precast cement concrete coloured chemically treated interlocking paver block any shape and size conforming to IS-15658-2006 of 60 mm thickness M-35 grade with grey cement and pigment laid over and including 40mm thick uniformly levelled surface of stone dust cushioning including dismantling of floor, hearth or wall tiles / terrazo including cement mortar bedding (but not backing), removal servicable tiles from site and rubbish off the premises complete all as specified and directed..

M&L for formwork to sides & soffits of floor or roof beams, beam , lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floors & beams, etc. rough finished surfaces of concrete flat complete all as specified and directed..

M&L for RCC design mix M-25 (using 20mm graded stone aggregates) as in beams, cantilevers, bressummers, lintels over 1.5m span, lintel band, etc complete all as specified and directed

M/S vikas jain