Interior Fit-Out and Renovation Works of SIDBI Officers Flats (2 Nos. 3 BHK and 1 No. 2 BHK) and External works at Kings Apartment, Lucknow (U.P.)

Name of work: Interior Fit-Out Works of SIDBI Officers’ Flats (2 Nos. 3 BHK & 1 No. 2 BHK) and External works at Kings Apartment, Lucknow

S.NO DESCRIPTION DSR AMOUNT NS AMOUNT

SIDBI Officers’ Flats (2 Nos. 3 BHK & 1 No. 2 BHK)

2 PLUMBING FIXTURES WORKS ₹ 127,210.98 ₹ 569,301.00

3 ELECTRCAL FIXTURE WORKS ₹ 717,887.00 ₹ 0.00

4 LIGHT FIXTURE WORKS ₹ 0.00 ₹ 297,923.00

1 CIVIL (EXTERNAL WORKS) ₹ 3,147,414.22 ₹ 895,480.00

GRAND TOTAL (I/C GST) ₹ 11,763,699.00

GRAND TOTAL (I/C GST) ₹ 11,763,699.00

Digitally signed by AMIT

CIVIL & ALLIED WORKS (For flat interior works)

S.No. DSR No. Description of Item Unit Qty Rate (Rs) DSR Amount(Rs) Non DSR Amount(Rs)

Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class

designation 7.5 in superstructure above plinth level up to floor V level.

1.1 6.13.2 Cement mortar 1:4 (1 cement :4 coarse sand) Sqm 6.00 1123.8 ₹ 6,742.80

CEMENT PLASTER :- 15 mm cement plaster on the rough side of single or half brick

3 13.4 12 mm cement plaster of mix

Repairs to plaster of thickness 12 mm to 20 mm in patches of area

2.5 sq.meters and under, including cutting the patch in proper shape,

4 14.1 raking out joints and preparing and plastering the surface of the walls

complete, including disposal of rubbish to the dumping ground, all

complete as per direction of Engineer-in-Charge.

4.1 14.1.2 With cement mortar 1:4 (1cement: 4 coarse sand) SQM 60.00 560.5 ₹ 33,630.00

Providing and fixing stone slab with table rubbed, edges rounded and

polished, of size 75x50 cm deep and 1.8 cm thick, fixed in urinal

partitions by cutting a chase of appropriate width with chase cutter and

5 8.10 embedding the stone in the chase with epoxy grout or with cement

concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 6

mm nominal size) as per direction of Engineer-in-charge and finished

5.1 8.10.2 Granite Stone of approved shade Sqm 40.00 4051.85 ₹ 162,074.00

Providing edge moulding to 18 mm thick marble stone counters, Vanities etc.,

6 8.3 including machine polishing to edge to give high gloss finish etc. complete as per

design approved by Engineer-in-Charge.

Extra for providing opening of required size & shape for wash basin/kitchen sink in

kitchen platform, vanity counter and similar location in marble/ Granite/ stone work,

including necessary holes for pillar taps etc. including moulding, rubbing and

polishing of cut edges etc. complete

Providing wood work in frames of doors, windows, clerestory windows and other

frames, wrought framed and fixed in position with hold fast lugs or with dash

fasteners of required dia & length (hold fast lugs or dash fastener shall be paid

for separately).

8.1 9.1.1 Second class teak wood cum 0.25 142949.7 ₹ 35,737.43

Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I)

non-decorative type, core of block board construction with frame of 1st class hard

wood and well matched commercial 3 ply veneering with vertical grains or cross

bands and face veneers on both faces of shutters:

9.1 9.21.1 35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws sq m 15.00 2,392.65 ₹ 35,889.75

Providing and fixing plywood 4 mm thick, both side decorative veneer

conforming to IS: 1328 (type-1), for plain lining / cladding with necessary

screws, Including designinig and grooving including door frames of veneer as per the

requirement of the client

Polishing in high gloss/matt finish melamine clear polish on

11 13.116 wood work in required color/wooden shade texture with

following process in the sequence as detailed below:

Digitally signed by AMIT

S.No. DSR No. Description of Item Unit Qty Rate (Rs) DSR Amount(Rs) Non DSR Amount(Rs)

1. The surface to be polished is rubbed with sand paper 80/

120 no. and then with sand paper of 160/180 nos.

2. Applying two coats of sealer with spray gun and allowing

sufficient drying time for 1st coat and 2nd coat is allowed

to dry for 8 to 12 hrs.

3. On drying of sealer coat, wet rubbing with emery cloth of

finer grading with ample water to remove excess sealer

layer and make the surface further smooth after this wet

rubbing, then surface is applied with special grade

melamine fillers to fill all the small and big holes/grooves

etc. Filler coat to be allowed to dry for 4 to 6 hrs on which

again a light wet rubbing is done this surface is further

allowed to dry for 12 hrs.

4. On this, 1st coat of melamine polish is applied with spray

gun using melamine clear polish and melamine thinner

in required proportion. This 1st coat is allowed to dry for

24 hrs then this dry surface is again fine wet rubbed smooth,

which is further allowed to dry for 12 hrs. The final

melamine polish is applied with compressor pressure spray

gun using melamine clear polish and melamine thinner

mixed in required proportion complete as per direction of

Engineer-in-Charge. (Final coat to be done in 1 or 2 layers

without gap of time.)

Providing & Fixing decorative high pressure laminated sheet of plain / wood grain in

gloss / matt/ suede finish with high density protective surface layer and reverse side

of adhesive bonding quality conforming to IS : 2046 Type S, including cost of adhesive

of approved quality

Providing and fixing various hardware fittings of approved make complete for all

doors of one 3 BHK flat, comprising SS tower bolts (200 mm & 250 mm), mortice

locksets with handle and key, main door lock, cylindrical locks, magic eye, main door

grace handles, stainless steel ball bearing hinges, magnetic door buffers, vanity SS

legs, screws, fasteners and all other accessories required for proper installation,

including dismantling of existing hardware wherever required, fitting, fixing,

alignment, testing and making good the disturbed surfaces complete in all respects as

directed by the Engineer-in-Charge and Quanties as per site is given below:

A Material UoM

1 SS Tower bolt (barrel type) 200x10mm - Nos. 14.00

2 SS Tower bolt (barrel type) 250x10mm- Nos. 11.00

3 75mm metal magnetic buffer Nos. 7.00

4 Oval shape SS Hanging rod (Length 470mm each) Mtr 1.00

5 Magic Eye Nos. 1.00

6 Mortice Lock with handle and key Nos. 8.00

7 Main door Lock Nos. 1.00

8 Cylindrical lock Nos. 3.00

9 Vanity SS Leg Nos. 4.00

10 Main Door Grace Handle 360mm high Nos. 2.00

11 Double Ball Bearing Stainless Steel Hinge (4inchx3inchx3mm) Nos. 48.00

12 Hardware and screw etc Nos. 1.00

Digitally signed by AMIT

S.No. DSR No. Description of Item Unit Qty Rate (Rs) DSR Amount(Rs) Non DSR Amount(Rs)

Providing and fixing various hardware fittings complete for one 2 BHK flat

comprising approved make SS tower bolts (200 mm & 250 mm), mortice locksets

with handles and keys, main door lock, cylindrical locks, magic eye, oval shape

stainless steel hanging rod, main door grace handles, stainless steel ball bearing

14 MR hinges, magnetic door buffers, vanity SS legs, screws, fasteners and all other Nos 1.00 60,000.00 ₹ 60,000.00

accessories required for proper installation, including dismantling of existing

hardware wherever required, fitting, fixing, alignment, testing and making good the

disturbed surfaces complete in all respects as directed by the Engineer-in-Charge and

Quanties as per site is given below:

A Material UoM

1 SS Tower bolt (barrel type) 200x10mm Nos. 8.00

2 SS Tower bolt (barrel type) 250x10mm Nos. 10.00

3 Oval shape SS Hanging rod (Length 470mm each) Mtr 1.00

4 75mm metal magnetic buffer Nos. 4.00

5 Magic Eye Nos. 1.00

6 Mortice Lock with handle and key Nos. 6.00

7 Main door Lock Nos. 1.00

8 Cylindrical lock Nos. 2.00

9 Vanity SS Leg Nos. 4.00

10 Main Door Grace Handle 360mm high Nos. 2.00

11 Double Ball Bearing Stainless Steel Hinge (4inchx3inchx3mm) Nos. 36.00

12 Hardware and screw etc Job 1.00

TILE DADO :- Providing and laying Vitrified tiles in floor in different sizes (thickness

to be specified by the manufacturer) with water absorption less than 0.08% and

conforming to IS:15622, of approved brand & manufacturer, in all colours and shade,

laid on 20 mm thick cement mortar 1:4 (1 cement: 4 coarse sand) jointing with grey

cement slurry @3.3 kg/sqm including grouting the joints with white cement and

15 11.41A.1.1 matching pigments etc. The tiles must be cut with the zero chipping diamond cutter SQM 120.00 1,453.65 ₹ 174,438.00

only . Laying of tiles will be done with the notch trowel,

plier, wedge, clips of required thickness, leveling system and rubber mallet for placing

the tiles gently and easily.

Double charge vitrified tile polished finish of size

Size of Tile 600 x 600 mm

TILE FLOORING :- roviding and laying Vitrified tiles in floor in different sizes

(thickness to be specified by the manufacturer) with water absorption less than

0.08% and conforming to IS:15622, of approved brand & manufacturer, in all colours

and shade, laid on 20 mm thick cement mortar 1:4 (1 cement: 4 coarse sand) jointing

16 11.41A.3 with grey cement slurry @3.3 kg/sqm including grouting the joints with white SQM 45.00 1,577.15 ₹ 70,971.75

cement and matching pigments etc. The tiles must be cut with the zero chipping

diamond cutter only . Laying of tiles will be done with the notch trowel,

plier, wedge, clips of required thickness, leveling system and rubber mallet for placing

the tiles gently and easily.: Size of Tile 600 x 1200 mm

Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622

(thickness to be specified by the manufacturer), of approved make, in all colours,

shades except burgundy, bottle green, black of any size as approved by Engineer-in-

Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar

1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm,

including pointing in white cement mixed with pigment of matching shade complete.

Digitally signed by AMIT

S.No. DSR No. Description of Item Unit Qty Rate (Rs) DSR Amount(Rs) Non DSR Amount(Rs)

Grouting the joints of flooring tiles having joints of 3 mm width, using epoxy grout

mix of 0.70 kg of organic coated filler of desired shade(0.10 kg of hardener and

0.20 kg of resin per kg), including filling/grouting and finishing complete as per

direction of Engineer-in-charge.

Finishing walls with 100% Premium acrylic emulsion paint having VOC less than

50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance,

dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon

New work (Two or more coats applied @ 1.43 litre/10 sqm. Over and including

priming coat of exterior primer applied @ 0.90 litre/10 sqm.

Removing dry or oil bound distemper, water proofing cement paint and the like

20 13.91 by scrapping, sand papering and preparing the surface smooth including necessary Sqm 1200.00 25.15 ₹ 30,180.00

repairs to scratches etc. complete.

Painting with synthetic enamel paint of approved brand and manufacture of required

colour to give an even shade :

21.1 13.99.1 One or more coats on old work. Sqm 50.00 102.8 ₹ 5,140.00

Cutting holes of required size in brick masonry wall for fixing of exhaust fan

22 14.81 including providing and fixing 300 mm dia PVC pipe conforming BIS-12818 and No. 9.00 288.1 ₹ 2,592.90

making good the same etc. complete as per direction of Engineer-in-charge.

Hacking of CC flooring including cleaning for surface etc. complete as per direction of

the Engineer-in-Charge.

Dismantling 15 to 40 mm dia G.I. pipe including stacking of dismantled pipes (within

50 metres lead) as per direction of Engineerin-Charge.

24.1 (a) Internal Work- Exposed on wall metre 69.00 3.25 ₹ 224.25

Taking out existing wooden door shutter, repair by cutting, painting etc. and refixing

of repaired door shutters to existing door frames, including replacement of hinges

with screws, etc. as required, all

complete as per the direction of the Engineer-in-charge.

Demolishing brick work manually/ by mechanical means including stacking of

26 15.7 serviceable material and disposal of unserviceable material within 50 metres lead as

per direction of Engineer-in-charge..

Dismantling doors, windows and clerestory windows (steel or wood) shutter

27 15.12 including chowkhats, architrave, holdfasts etc. complete and stacking within 50

Dismantling steel work in single sections including dismembering and stacking within

50 metres lead in:

28.1 15.17.2 Channels, angles, tees and flats Kg 375.00 2.3 ₹ 862.50

Dismantling tile work in floors and roofs laid in cement mortar including stacking

material within 50 metres lead.

29.1 15.23.1 For thickness of tiles 10 mm to 25 mm Sqm 150.00 73.4 ₹ 11,010.00

29.2 15.23.2 For thickness of tiles above 25 mm and up to 40 mm Sqm 30.00 113.35 ₹ 3,400.50

Disposal of building rubbish / malba / similar unserviceable, dismantled or

waste materials by mechanical means, including loading, transporting, unloading to

approved municipal dumping ground or as approved by Engineer-in-charge, beyond

50 m initial lead, for all leads including all lifts involved.

Supplying and fixing SS Curtain rod on door and windows with required SS

31 MR bracket. Rate also include s/f end funnels /cap of approve design as per site RMT 75.00 826.00 ₹ 61,950.00

Digitally signed by AMIT

S.No. DSR No. Description of Item Unit Qty Rate (Rs) DSR Amount(Rs) Non DSR Amount(Rs)

Carefully dismantling the existing cupboard wooden shutters, shelves, partitions and

all associated components, removing debris from site and making good the

uneven/disturbed surfaces created due to dismantling. Thereafter providing and

fixing modular wardrobe of approved design, size and configuration with sliding

shutters, fabricated from 18 mm thick HDHMR board (Greenpanel/Action

TESA/Century or approved equivalent) for sides, top, bottom, shelves, vertical

partitions and shutters, finished with approved shade 0.8 mm thick decorative

laminate (Greenlam/Merino/Century/Royale Touche or approved equivalent) on all

internal surfaces and 1.0 mm thick decorative laminate on all external exposed

surfaces, including 8 mm thick pre-laminated HDHMR backing board. The item shall

include 2 mm thick PVC edge banding on all exposed edges and 0.8 mm PVC edge

banding on internal edges, heavy-duty soft-close sliding shutter system of

Hafele/Hettich or approved equivalent, soft-close telescopic drawer channels, two

lockable drawers, SS hanging rod, concealed SS handles, locks, buffers, stoppers,

screws, adhesives, fittings, fixtures and all necessary hardware and accessories

complete. Back of wardrobe is finished wih 8mm prelaminated HDHMR board

.Each wardrobe shall also have 2 drawer with locking arrangement .Shutter

of the wardrobe should be sliding with soft close sliding channel of Hafle

make/EquivalentThe work shall also include cutting, edge finishing, groove making

wherever required, fabrication, assembly, transportation, installation, alignment,

making necessary cut-outs and adjustments, finishing the exposed surfaces smooth

and complete in all respects as per approved drawings, design and direction of

Engineer-in-Charge. Measurement shall be made on the front elevation area of the

wardrobe (Height × Width).

Providing and laying water proofing treatment in sunken portion of WCs, bathroom

33 22.5 etc., by applying cement slurry mixed with water proofing cement compound

consisting of applying :

(a) First layer of slurry of cement @ 0.488 kg/sqm mixed with water proofing

cement compound @

0.253 kg/ sqm. This layer will be allowed to air cure for 4 hours.

(a) First layer of slurry of cement @ 0.488 kg/sqm mixed with water proofing

cement compound @

0.253 kg/ sqm. This layer will be allowed to air cure for 4 hours.

(The rate includes preparation of surface, treatment and sealing of all joints,

corners, junctions of pipes and masonry with polymer mixed slurry.)

34 MR MODULAR KITCHEN WORK

Providing and fixing modular kitchen units for the kitchen platform and top

wall units to be fabricated by using HDHMR board of thickness 18 mm for

making cabinets of required sizes to match with the sizes SS kitchen jali units and

size of the SS sink as per following details :-

Front bottom , top sides and shelf partitions of the modular cabinets shall be

of 18 mm thick HDHMR boards of Mls Green panel Industries or approved

equivalent and back portion shall be of 8 mm thick HDHMR board or approved

make or equivalent with necessary fittings , screws , pasting materials, finishing all

exposed cut surfaces with self adhesive PVC tape in matching shade as that of

laminate . The shutters and the pull out units shall be fixed 50 mm above the

kitchen floor level . All the inner portions of the cabinets shall be finished with

0.8 mm thick laminate of white colour and approve make..The front face of the

cabinet shall be finished with1.0 mm ultra gloss laminate shade 21162 MR+ &

21069 MR+ approved make. Quoted rates shall be inclusive of labour ,

materials wastage scaffolding fixing arrangements of top and bottom

units with necessary dash fasteners , repairing the damages, shifting the debris

out of colony , CP , taxes etc all as required for the execution of the work . Note :-Only

front elevation area shall be measured for payment purpose.

Digitally signed by AMIT

S.No. DSR No. Description of Item Unit Qty Rate (Rs) DSR Amount(Rs) Non DSR Amount(Rs)

Providing and fixing 18-20 mm thick machine polished granite countertop of

approved shade and make over modular kitchen base units including edge polishing,

cut-outs for sink, hob and accessories, complete as required.

Providing and fixing 600 mm high granite/quartz/glazed tile backsplash above

kitchen platform including adhesive, grouting and finishing complete.

Providing and fixing 100 mm high PVC/HDHMR removable skirting below base units

with necessary clips and accessories complete.

Providing and fixing heavy duty adjustable PVC legs/supports for base units including

fixing accessories complete.

Cut-out provision for built-in hob complete

Tandem drawer systems with soft close channels of Hettich/Hafele/Ebco/Equivalent

approved make. Each 3.00 326000 ₹ 978,000.00

Wicker basket for vegetable storage

SS 304 dish drainer unit with tray complete

Sink base cabinet to be lined with aluminium/PVC protective tray to prevent moisture

All exposed edges shall be finished with 2 mm PVC edge banding applied through hot

melt edge banding machine

All shutters and drawers shall be provided with soft close mechanism

Necessary cut-outs for electrical points, RO, microwave, chimney, dishwasher,

refrigerator and other kitchen appliances complete

34.2 Top wall units of depth 300 mm approx. with shelves

Providing and fixing stainless steel baskets and other fittings , accesories of

34.3 modular kitchen of Mls Hettich or approved equivalent make as per below

mentioned details :-

34.4 SS 304 cutlery baskets 15 x20 x4 inch

34.5 SS 304 Plain basket 15 x20 x6 inch

34.6 SS 304 thali basket 15 x20 x8 inch

34.7 SS 304 plain baskets 19 x20 x4 inch

34.8 SS 304 plain basket 19 x20 x 6 inch

34.9 SS 304 plain basket 19x 20 x8 inch

34.10 SS baskets S —Corner basket

34.11 SS detergent pullout

34.12 SSdustbin ring

34.13 Bottle Pull out basket set of width 9" with standard depth

34.14 SS Handle 12 inch size Basic price 400

34.15 SS auto close hinges soft close of all variety of approved make

34.16 telescopic channels 20 " size

34.17 S/F Chimney 600 mm wide of approved make with vent pipe Basic price 22500

34.18 S/F granite kitchen sink 36 x18 x8 with drain board of approved make

The quoted rate shall be deemed to include all shutters, carcasses, shelves, hardware,

baskets, skirting, countertop, sink, chimney, edge banding, cut-outs, accessories,

transportation, loading-unloading, installation and all incidental works required for a

complete functional modular kitchen

Removing the existing plumbing fixtures carefully and stacking the reusable fixture at

35 MR safe/designated place, including dicardeding the unusable fixture after approval from Job 3.00 5000.00 ₹ 15,000.00

Engineer In Charge (Per Flat)

Three track three panels sliding window with fly proof SS wire mesh (Two nos. glazed

& one no. wire mesh panels) made of (small series) frame 92 x 44 mm & sash 32 x 60

mm both having wall thickness of 1.9 ± 0.2 mm and single glazing bead of appropriate

dimension (Area of window upto 1.75 sqm).

Casement window single panel with S.S. friction hinges (300 x 19 x 1.9 mm),

made of (small series) frame 47 x 50 mm & sash 47 x 68 mm both having wall

thickness of 1.9 ± 0.2 mm and single glass pane glazing bead of appropriate

dimension. (Area of window upto 0.75 sqm.)

Diamomd polishing marble work/Granite work/ stone work where exer required to

give high gloss finish complete

Digitally signed by AMIT

S.No. DSR No. Description of Item Unit Qty Rate (Rs) DSR Amount(Rs) Non DSR Amount(Rs)

Providing and fixing of Decorative Door Bidding around the choukhat along with

39 MR necessary hardware etc of approved quality complete in all respect as direction of Rmt 92.00 160.00 ₹ 14,720.00

engineer-in -charge

Providing and fixing factory-made decorative aluminium security grills for external

windows, manufactured from aluminium alloy sections conforming to IS 733 and IS

1285, with minimum 1.5–2.0 mm thick sections, powder coated (minimum 60–80

microns) in approved colour, including all brackets, stainless steel fasteners, anchor

bolts, accessories and fixing arrangement: for covering of entire external windows of

approved quality complete in all respect as direction of engineer-in -charge

Providing and filling cinder in sunken portions of existing toilet and kitchen including

all lift and lead up to 6th floor, complete as direction of engineer-in-charge

Providing and laying in position ready mixed or site batched design

mix cement concrete for plain cement concrete(PCC) work; using coarse

aggregate and fine aggregate derived from natural sources and using

recycled concrete aggregate (RCA) as coarse aggregate and fine

aggregate within the permissible utilization, Portland Pozzolana /

Ordinary Portland/Portland Slag cement, admixtures in recommended

proportions as per IS: 9103 to accelerate / retard setting of concrete

to improve durability and workability without impairing strength;

including pumping of concrete to site of laying, curing, carriage for all

leads; but excluding the cost of centering, shuttering and finishing as

per direction of the engineer-in-charge; for the following grades of

Note: Extra cement up to 10% of the minimum specified cement content

in design mix shall be payable separately. In case the cement content

in design mix is more than 110% of the minimum specified cement

content, the contractor shall have discretion to either re-design the

mix or bear the cost of extra cement.

Concrete of M10 grade with minimum cement

content of 220 kg /cum.

Brick work with common burnt clay modular bricks of class designation

7.5 in foundation and plinth in:

43.1 6.2.1 Cement mortar 1:4 (1 cement : 4 coarse sand) Cum 5.00 6504.90 ₹ 32,524.50

Core cutting for Chimany outlet including necessary hardware complete as per

direction of Engineer-incharge.

Grading roof for Water Proofing treatment with Cement Concrete 1:2:4 (1 cement:2

coarse sand:4 graded stone aggregate 20mm nominal size).

Providing and applying white cement based putty of average thickness 1.0mm, of

46 13.80 approved brand and manufacturer, over the plastered wall surface to prepare the Sqm 1200.00 156.05 ₹ 187,260.00

surface even and smooth complete.

French spirit polishing: Two or more coats on new works including a coat of wood

Demolishing Cement Concrete manually/by mechanical mean including disposal of

material within 50Mtr lead as per direction of Engineer-in-charge.

48.1 15.2.1 Nominal concrete 1:3:6 or richer mix (i/c equivalent design mix) Cum 2.00 2434.25 ₹ 4,868.50

Dismantling doors, Windows and clerestory window (steel or wood) shutter including

chowkhats, architrave holdfast etc. complete and stacking within 50Mtr lead:

15.12.1 of area 3 sq. Mtrs and below Nos 44.00 367.20 ₹ 16,156.80

Dismantling old plaster or skirting raking out joint and cleaning surface for plaster

including disposal of rubbish to the dumping ground within 50Mtr lead.

Digitally signed by AMIT

S.No. DSR No. Description of Item Unit Qty Rate (Rs) DSR Amount(Rs) Non DSR Amount(Rs)

Extra for fixing marble/granite stone over and above corresponding basic item, in

51 8.4 fascia and drop of width up to 150mm with epoxy resin based adhesive including Mtr 72.00 568.55 ₹ 40,935.60

cleaning etc. complete.

Providing and fixing double glazed hermetically sealed glazing in aluminum window,

ventilator and partition etc. with 6mm thick clear float glass both side, having 1mm

52 21.10 air gap including providing EPDM gasket, perforated aluminum spacer, desiccant, Sqm 35.00 4997.7 ₹ 174,919.50

sealant (Both primary and secondary sealant) etc. as per specification, drawing and

direction of Engineer-in-charge complete.

Scrapping the existing multilayered polishing over existing door and door frame by

53 MR sand papering/ paint remover, scrubber etc. and preparing the surface smooth ready Sqm 200.00 480 ₹ 96,000.00

to take new polishing including necessary repairs as directed by Engineer-In-Charge

Demolishing R.C.C. work manually/by mechanical means including stacking of steel

54 15.30 bar and disposal of unservice-able material within 50meter lead as per direction of Cum 2.00 3551.25 ₹ 7,102.50

Engineer-in-charge.

Providing and fixing toilet vanity cabinet of approved design and size, fabricated from

18 mm thick HDHMR board, finished with approved shade 1.0 mm thick decorative

laminate on external exposed surfaces and 0.8 mm thick laminate on internal surfaces,

including 2 mm thick PVC edge banding on exposed edges, SS hinges, handles,

magnetic catch, screws, SS vanity legs, approved adhesive, cutting, edge finishing,

55 MR making necessary openings for plumbing connections and all other hardware and Nos. 6.00 8500 ₹ 51,000.00

accessories complete. The item shall also include providing and fixing 16-18 mm thick

machine-polished granite top of approved colour and shade with necessary edge

moulding/polishing, cut-outs for wash basin and fittings, including fixing with

suitable adhesive/sealant, complete in all respects as per approved design and

direction of Engineer-in-Charge.

Providing & fixing PVC sheet behind toilet door with adhesive bonding quality

56 MR conforming to IS:2046 Type S, necessary hardware etc of approved quality complete Sqm 12.00 1100 ₹ 13,200.00

in all respect as directed by Engineer-In-Charge

MULTIPLYING FACTOR FOR labour cess ₹ 2,753,600.32

Grand Total of Civil Works ₹ 2,836,208.33 ₹ 3,172,274.00

Grand Total of Civil Works ₹ 2,836,208.33 ₹ 3,172,274.00

Digitally signed by AMIT

PLUMBING FIXTURE WORKS

S.No. DSR No. Description of Item Unit Qty Rate (Rs) DSR Amount(Rs) NS DSR Amount(Rs)

Providing and fixing 8 mm dia C.P. / S.S. Jet with flexible tube upto 1 metre long with S.S.

1 17.16A triangular plate to Eureopean type W.C. of quality and make as approved by Engineer - in - Nos. 6.00 349.15 2094.90

Providing and fixing CP Brass 32mm size Bottle Trap of approved quality & make

and as per the direction of Engineer-in-charge.

Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings

17.28.1 Semi rigid pipe

4 MR Providing and fixing CP Waste Coupling for wash basin and sink

4.1 a) CP Waste coupling 31 mm dia of 79 mm length and 62 mm breadth Nos. 6.00 850.0 5100.00

4.2 b) CP Waste coupling 38 mm dia of 83 mm length and 77 mm breadth Nos. 3.00 1150.0 3450.00

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal

stability for hot & cold water supply, including all CPVC plain & brass threaded fittings,

i/c fixing the pipe with clamps at

5 18.8 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent

cement and the cost of cutting chases and making good the same including testing of

joints complete as per direction of Engineer in Charge. :Concealed work, including cutting

chases and making good the walls etc.

5.1 18.8.1 15 mm nominal outer dia .Pipes. Metre 38.00 497.8 18916.40

5.2 18.8.2 20 mm nominal outer dia .Pipes. Metre 38.00 537.6 20428.80

5.3 18.8.3 25 mm nominal outer dia .Pipes. Metre 18.00 627.25 11290.50

6 18.21 Providing and fixing uplasticised PVC connection pipe with brass unions :

Supplying and fixing looking mirror of 5 mm thick looking glass with bevelled

edges and holes as per site requirement of Modi Gaurd or other approved equivalent

Rates are inclusive of fixing of glass with SS stud all complete as directed by

Engineer Incharge

Providing and fixing in position quality Towel rod of 24" length with brackets fixed

8 MR over tiles with rowel plug and approved quality screws including cutting and Each 6.00 1652.00 9912.00

making good the tiles.

Providing and fixing in position quality Towel ring fixed over tiles with rowel

plug and approved quality screws including cutting and making good the

damages of tiles etc. all complete as required at site as directed by the Engineer-in-

Digitally signed by AMIT

S.No. DSR No. Description of Item Unit Qty Rate (Rs) DSR Amount(Rs) NS DSR Amount(Rs)

Supplying and fixing position the following approved make fittings & fixtures,

10 MR including carefully removing the existing old/damaged fittings & fixtures and

handing over the same

15 mm dia. C.P. Brass bib cock with nozzle wall CP. flange of approved equivalent

15 mm dia. C.P angle valve with wall CP. flange of continental series of approved

equivalent make.

15 mm dia. C.P. Brass central hole single lever wash basin mixer of approved

equivalent make including plumbing fittings and 450 mm long braided hoses etc. all

complete as required at site./ Wall mounted with internal concealed part of brass

15 mm dia. C.P. 4 way high flow single lever divertor with cover plate ,c.p pin .

10.4 (v) Including all plumbing fittings& fixtures etc all complete as required at site as Each 6.00 7670.00 46020.00

directed by ENGINEER IN CHARGE

10.5 (vi) 15 mm dia C.P spout of approve design with c.p flexible tube of required length Nos. 6.00 6490.00 38940.00

10.6 (vii)- a) C.P Overhead shower 150 X150 mm with 450 mm long C.P Shower Arm J Nos. 6.00 6844.00 41064.00

100mm dia. Heavy quality detachable stainless steel Jali (grating) with or without

holes for waste pipe of floor / Nahani trap etc all complete as required at site as

Engineer In charge

11.1 (ix) Heavy quality CP Soap dish of approved equivalent make. Each 6.00 1062.00 6372.00

11.2 (xi) 15 mm dia. C.P brass conceled stop cock with upper body plate Each 9.00 2124.00 19116.00

Providing & fixing in position 1st quality vitreous china glazed wall mounted

European WC of standard size with either P trap as per site requirement and

providing & fixing conceled cistern with required material ,labour etc i/c cover plate

Providing and fixing in position 100 mm dia. and 75mm outlet pvc Nahani/

floor trap having seal of 40 mm to 50mm, approved equivalent ISI mark having necessary

length of extension pipe wherever required including cutting of concrete and

repairing with concrete after completion all complete.

Supplying and fixing table top square washbasin 40x40 cm of with c.p waste

14 MR coupling and heavy duty waste pipe all complete as required at site as directed Each 6.00 8850.00 53100.00

by Engineer-in-Charge

15 MR Providing and fixing automatic soap dispenser Nos. 6.00 4000.00 24000.00

16 MR Providing and fixing Paper holder of approved design Nos. 6.00 1800.00 10800.00

Digitally signed by AMIT

S.No. DSR No. Description of Item Unit Qty Rate (Rs) DSR Amount(Rs) NS DSR Amount(Rs)

Providing and fixing on wall face unplasticised Rigid PVC rain water

pipes conforming to IS : 13592 Type A, including jointing with seal

ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion,

(i) Single socketed pipes.

Providing and fixing of soil, waste, vent and rain water SWR uPVC Pipe of including all

fitting (plain or door) e.g. bend, junction, cowl, offset, access piece including holder bat

clamp of approved design to uPVC pipe, embedded cement concert block 10x10x10cm of

1:2:4 (1 cement:4 coarse sand:4 graded stone aggregate 20mm nominal size), cutting

holes in wall and floor, excavation, refilling and disposal of surplus earth where required

and marked good complete.

Providing, fixing & testing uPVC Pipe, conforming to IS 4985 class 3 (6kg/ cm2) including

19 MR - 3 injection molded fitting, jointing with solvent cement, cutting and making good the floors 0.00

and walls and jointing to trap/waste pipe, complete of outer dia. (Indirect waste)

(a) 40mm dia Mtr pipe Mtr 5.00 552.00 2760.00

(b) 63mm diameter pipe Mtr 22.00 761.00 16742.00

Providing and fixing CP brass Tube spout Kitchen Faucet complete with flow rate 2.5litre

per minute at 3 bar including cutting and making good the wall where required.

21 MR -5 Providing, Fixing wall mounted Double Coat hook on door complete. Nos. 6.00 1288.00 7728.00

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipe having thermal stability for

hot & cold Water Supply, including all CPVC plain & brass threaded fitting, including fixing

the pipe with clamps at 1.0m spacing. This include jointing of Pipe & fitting with one step

CPVC solvent cement and testing of joint complete as per direction of Engineer in Charge.

43284 25mm Nominal outer dia Pipe Mtr 60.00 401.55 24093

43285 32mm Nominal outer dia Pipe Mtr 30.00 518.75 15562.5

MULTIPLYING FACTOR FOR GST CORRECTION AS PER DSR 2023 0.973 123505.809

COST INDEX @ 1.03 127210.983

Grand Total of Plumbing Works 127210.98 569301.00

Grand Total of Plumbing Works 127210.98 569301.00

Digitally signed by AMIT

ELECTRICAL & ALLIED WORKS

S.No. EM Description of Item Quantity Unit Rate (Rs) DSR Amount(Rs) Amount(Rs)

Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5

sq.mm FRLS PVC insulated copper conductor single core cable in surface /

recessed medium class PVC conduit, with modular switch, modular plate,

suitable Gl box and earthing the point with 1.5 sq.mm FRLS PVC insulated

copper conductor single core cable etc. as required.

Wiring for twin control light point with 1.5 sq.mm FRLS PVC insulated

copper conductor single core cable in surface / recessed medium class

PVC conduit, 2 way modular switch, modular plate, suitable Gl box and

2 1.11 earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single 40.00 Point 1803.00 72120.00

etc. as required.

Wiring for light/ power plug with 2X4 sq. mm FRLS PVC insulated

copper conductor single core cable in surface/ recessed medium class PVC

conduit along with 1 No. 4 sq. mm FRLS PVC insulated copper conductor single

core cable for loop

earthing as required.

Wiring for circuit/ submain wiring along with earth wire with the following

sizes of FRLS PVC insulated copper conductor, single core cable in surface/

4 1.14 recessed medium class PVC conduit

Supplying and drawing following sizes of FRLS/HFFR PVC insulated copper

1.17 conductor, single core cable in the existing surface/ recessed steel/ PVC conduit

Rewiring for light point/ fan point/ exhaust fan point/

call bell point with 1.5 sq.mm FRLS/HFFR PVC

insulated copper conductor single core cable and 1.5

5 1.15 sq.mm FRLS/HFFR PVC insulated copper conductor

single core cable as earth wire in existing surface/

recessed steel/PVC conduit including dismantling as

Digitally signed by AMIT

S.No. EM Description of Item Quantity Unit Rate (Rs) DSR Amount(Rs) Amount(Rs)

Supplying and drawing following pair 0.5 mm dia FRLS PVC insulated

annealed copper conductor, unarmored telephone cable in the existing

6 1.18 surface/ recessed steel/ PVC conduit as

Supplying and drawing co-axial TV cable RG-6 grade, 0.7 mm solid copper

conductor PE insulated, shielded with fine tinned copper braid and protected

7 1.19 with PVC sheath in the existing surface/ recessed steel/ PVC conduit as 150.00 Metre 54.00 8100.00

Supplying and fixing of following sizes of medium class PVC conduit along

with accessories in surface/recess including cutting the wall and making good

8 1.21 the same in case of recessed

conduit as required.

Supplying and fixing suitable size Gl box with modular plate and cover in front

on surface or in recess, including providing and fixing 3 pin 5/6 A modular

9 1.31 socket outlet and 5/6 A modular 10.00 No. 545.00 5450.00

switch, connections etc. as required.

Supplying and fixing suitable size Gl box with modular plate and cover in front

on surface or in recess, including providing and fixing 6 pin 5/6 & 15/16 A

10 1.32 modular socket outlet and 15/16 A modular switch, connections etc. as required. 20.00 No. 659.00 13180.00

Supplying and fixing call bell/ buzzer suitable for single phase, V,

11 1.38 complete as required. 3.00 No. 112.00 336.00

Supplying and fixing suitable size Gl box with modular plate and cover in front

on surface or in recess, including providing and fixing 2 nos. 3 pin 5/6 A

12 1.56 modular socket outlet and 2 nos. 5/6 A modular switch, connections etc. as 8.00 No. 757.00 6056.00

required. (For light plugs to be used in non residential buildings).

Supplying & fixing suitable size Gl box with modular plate and cover in fronton

surface or in recess including providing and fixing 25 A modular socket outlet

13 1.57 and 25 A modular SP MCB, "C" curve including connections, painting etc. as 25.00 No. 807.00 20175.00

Supplying and fixing following modular switch/ socket

on the existing modular plate & switch box including

connections but excluding modular plate etc. as

Digitally signed by AMIT

S.No. EM Description of Item Quantity Unit Rate (Rs) DSR Amount(Rs) Amount(Rs)

14.6 1.24.6 Telephone socket outlet 15.00 Each 168.00 2520.00

14.7 1.24.7 TV antenna socket outlet 15.00 Each 168.00 2520.00

Supplying and fixing following size/module, GI box along with modular base &

cover plate for modular switched in recess etc. as required.

Supplying and fixing following way, horizontal type three pole and neutral,

sheet steel, MCB distribution board, 415 V, on surface/ recess, complete

with tinned copper bus bar, neutral bus bar, earth bar, din bar,

16 2.4 interconnections, powder painted including earthing etc. as required.

MCB/RCCB/lsolator)

Supplying and fixing 5 A to 32 A rating, 240/415 V, 10 kA, "C" curve, miniature

circuit breaker suitable for inductive load of following poles in the existing

17 2.10 MCB DB complete with connections, testing and commissioning etc. as

17.4 2.10.5 Triple pole and neutral 3.00 Each 1301.00 3903.00

Supplying and fixing following rating, four pole, (three phase and neutral),

415 volts, residual current circuit breaker (RCCB), having a sensitivity current 30

18 2.15 mA in the existing MCB DB complete with connections, testing and

commissioning etc. as

Supplying and fixing PVC batten/ angle holder including connections etc. as

Supplying and fixing 3 pin, 5 A ceiling rose on the existing junction box/ wooden

block including connections etc. as required.

Supplying and fixing modular blanking plate on the existing modular plate &

switch box excluding modular plate as required.

Supplying and fixing single pole blanking plate in the

existing MCB DB complete etc. as required.

Digitally signed by AMIT

S.No. EM Description of Item Quantity Unit Rate (Rs) DSR Amount(Rs) Amount(Rs)

Digitally signed by AMIT

ELECTRICAL FIXTURE WORKS

S.No. EM Description of item Unit Rate Amount DSR Amount NDSR

Dismantling Carefully disconnection and removing all fans, fittings, decorative lights, water

1 MR purifier, geysers, wires, conduits, casing capping , switch boards/ DB etc. in flat and keeping JOB 3.00 5310.00 10620.00

reusable items like exhaust fans ceiling/wall fans, LED batten water purifier, geyser etc.

Supplying ,Fixing, testing and commissioning of following Electrical items with necessary

SITC of LED tube light fixture of 4’ length 36 Watt white colour LED tube light on new white

colour square PVC block and using two/three core copper conductor PVC insulated

preferably white colourcable from tube light fixture to ceiling rose as directed by Engineer In

SITC of 48 inch BLDC Ceiling fan of approve shade with all necessary mounting accessories

2.2 with step regulator To provide 3 mm thick Bakelite round plate with required hardware near Nos. 15.00 2950.00 44250.00

the ceiling fan hook.

PVC exhaust fan of 200MM size with pvc louver protection complete with required

2.3 fittings and hardware etc. and using two/three core copper conductor PVC insulated Nos. 10.00 1652.00 16520.00

preferably white colourcable from exhaust fan to ceiling rose as directed by Engineer In Charge.

3 MR Supply and fixing of cool daylight colour led bulb 15W (Minimum 110lumens/watt) Nos. 32.00 450.00 14400.00

4 MR Supply and fixing of cool daylight colour led bulb 9W (Minimum 110 lumens/watt) Nos. 25.00 300.00 7500.00

Providing and Fixing Decorative warm white Wall Light with all necessary accessories etc without bulb

Providing and Fixing Decorative warm white Wall Light Blush with all necessary accessories etc

without bulb complete.

Supply and Installation of 12watt trim less surface round light of in balcony complete as direction

Engineer-in-charge.

Supply and Installation of 6Watt LED Down Light of in Toilet complete as direction Engineer-in-

Supply and Installation of 24Watt LED Down Light of in Kitchen complete as direction Engineer-in-

Supplying, Installation, testing and commissioning of 30/6 Amp auto mastic changeover speech ACCL

i/c connection etc.as required

11 MR Supply and Fixing of LED Mirror Light light 12w chrome complete as directed by Engineer-in-charge Nos. 6.00 3800.00 22800.00

12 MR Supply and Fixing of Light Pendant complete as directed by Engineer-in-charge Nos. 6.00 9316.50 55899.00

Digitally signed by AMIT

CIVIL WORK (EXTERNAL WORKS)

S.NO. DESCRIPTION UNIT BOQ DSR RATE DSR AMOUNT NDSR RATE NDSR AMOUNT

EXTERIOR FINISHING

1 13.45 Finishing walls with textured exterior paint of required shade :-

New work (Two or more coats applied @ 3.28 ltr/10 sqm) over and including priming coat of

exterior primer applied @2.20kg/10 sqm

Finishing with Deluxe Multi surface paint system for interiors and exteriors using Primer as per

manufacturers specifications :

Two or more coats applied on walls @ 1.25 ltr/10 sqm over and including one coat of Special

@ 0.75 ltr /10 sqm

Painting Steel work with Deluxe Multi Surface Paint to give an even shade. Two or more coat

b) 13.48.3 applied @ 0.90 ltr/10 sqm over an under coat of primer applied @ 0.80 ltr/10 sqm of approved SQM 280.00 170.70 47,796.00 -

brand and manufacture

Providing and applying white cement based putty of average thickness 1 mm, of approved brand

3 13.80 and manufacturer, over the plastered wall surface toprepare the surface even and smooth sqm 2900.00 156.05 452,545.00 -

Removing dry or oil bound distemper, water proofing cement paint and the like by scrapping, sand

papering and preparing the surface smooth including necessary repairs to scratches etc. complete.

Providing and fixing double scaffolding system (cup lock type) on the exterior side, up to seven

story height made with 40 mm dia M.S. tube 1.5 m centre to centre, horizontal & vertical tubes

joining with cup & lock system with M.S. tubes, M.S. tube challies, M.S. clamps and M.S. staircase

system in the scaffolding for working platform etc. and maintaining it in a serviceable condition for

the required duration as approved and removing it there after. The scaffolding system shall be

stiffened with bracings,runnrs, connection with the building etc wherever required for inspection

of work at required locations with essential safety features for the workmen etc. complete as per

directions and approval of Engineer-in-charge. The elevational area of the scaffolding shall be

measured for payment purpose. The payment will be made once irrespective of duration of

Painting (one or more coats) on rain water, soil waste and vent pipes and fittings with synthetic

enamel paint of approved brand and manufacture and required colour on old work

Repair to plaster of thickness 12 mm to 20 mm in patches of area 2.5 sqm and under, including

cutting the patch in proper shape, raking out joints and preparing plastering the wall surface with

7 14.75 white cement based polymer modified self curing mortar, including disposal of rubbish, all SQM 125.00 670.95 83,868.75 -

complete as per the direction of

Engineer-In-Charge.

Demolishing lime concrete manually/ by mechanical means and disposal of material within 50

metres lead as per direction of Engineer- in-charge.

Dismantling precast concrete or stone slabs in walls, partition walls etc. including stacking within 50

9 15.40 metres

15.40.2 Thickness above 40 mm up to 75 mm SQM 90.00 433.55 39,019.50 -

Digitally signed by AMIT

Dismantling old plaster or skirting raking out joints and cleaning the surface for plaster including

disposal of rubbish to the dumping ground within 50 metres lead.

Providing and fixing up to floor five level precast cement concrete string or lacing courses, copings,

bed plates, anchor blocks, plain window sills, shelves, louvers, steps, stair cases, etc., including

hoisting and setting in position with cement mortar 1:3 (1 Cement : 3 coarse sand), cost of required

Centering complete.

1:1.5:3 (1 cement : 1.5 coarse sand derived from natural sources : 3 graded stone aggregate 20 mm

size derived from natural sources)

Chipping of unsound/weak concrete material from slabs, beams, columns etc. with manual Chisel

and/ or by standard power driven percussion type or of approved make including tapering of all

13 26.28 edges, making square shoulders of cavities including cleaning the exposed concrete surface and

reinforcement with wire brushes etc. and disposal of debris for all lead and lifts all complete as per

direction of Engineer-In-Charge

26.28.1 75 mm average thickness sqm 25.00 378.00 9,450.00 -

Cleaning of reinforcement from rust from the reinforcing bars to give it a total rust free steel

surface by using alkaline chemical rust remover of approved make with paint brush and removing

loose particles after 24 hours of its application with wire brush and thoroughly washing with water

and allowing it to dry, all complete as per direction of Engineer-In-Charge.

a) 26.29.1 Bars upto 12 mm diameter rmt 30.00 8.25 247.50 -

b) 26.29.2 Bars above 12 mm diameter rmt 30.00 16.45 493.50 -

Rust Passivation: Two component, low solvent, zinc rich epoxy resin based Anticorrosive Treatment

of reinforcements in coats with time interval of minimum 4 hours between each coat of the

approved makes. The application shall be done by brush or spray as per Manufactureres

recommendation, complete. The rates are inclusive of all materials, labor, machinery, equipment,

tools, tackles etc. and disposal of debris, all complete. Mode of measurement will be per sqmt of

exposed area of concrete.

Corrosion Inhibitor- Coat of Concrete Penetrating Corrosion Inhibitor which works on Bipolar

Inhibition Mechanism of the approved makes on concrete surface to be repaired by using brush or

spray at dosage specified by the manufacturer. Mode of measurement will be per sqmt of exposed

area of concrete.

Providing, mixing and applying bonding coat of approved adhesive on chipped portion of RCC as

per specifications and direction of Engineer-In-charge complete in all respect.

26.31.2 Epoxy bonding adhesive having coverage 2.20 sqm/kg of approved make SQ MTR 30.00 285.20 8,556.00 -

Drilling suitable holes in reinforced or plain cement concrete with power driven drill machine to a

minimum depth of 100mm upto 200mm in RCC beams, lintels, columns and slabs to introduce steel

18 26.30 bars for sunshades/balconies including fixing the steel bars in position using epoxy resin anchor

grout of approved make but excluding the cost of reinforcement, all complete as per direction of

Engineer-In-Charge.

26.30.1 Upto and including 12mm dia Holes 70.00 141.20 9,884.00 -

Providing and fixing hard drawn steel wire fabric of size 75 x25 mm mesh or other suitable size wire

mesh to be fixed & firmly anchored to the concrete surface by means of “L” shaped mild steel

shear key welded with existing reinforcement including the cost of materials, labour, tool & plants

as approved by Engineer-in-charge.

Digitally signed by AMIT

Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592

20 12.41 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal

expansion, (i) Single socketed pipes.

21 13.4 12 mm cement plaster of mix

22 13.5 15 mm cement plaster on rough side of single or half brick wall of mix:

Structural steel work riveted, bolted or welded in built up sections, trusses and framed work,

24 10.1 including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer

Fixed to steel fabrication by welding Kg 440.00 133.70 58,828.00

Repair Micro concrete: Application of repair Micro-concrete of M40 grade for Making up lost

section of concrete for thickness more than 30mm, after the application of bonding agents to

ensure stability of the concrete, followed by curing with water for at least 7 days. The rates are

inclusive of all materials, labour, machinery, equipment, tools, tackles

Thixotropic Repair Mortar:

Repair with Dual shrinkage compensated, trowelable fibre reinforced thixotropic repair mortar.

Repairs to the deteriorated/damaged areas of RCC elements in the structure shall be carried out by

26 NDSR using powder Polymer Modified repair mortar. The polymer modified mortar is applied when the sqm 25.00 - 2200.00 55,000.00

epoxy bonding coat is still tacky. In one application maximum 25 mm thickness shall be built.

Subsequent layer shall be built with one bond coat of Polymer modified cement slurry. The

polymer modified repair mortar shall be mixed, applied and cured as per technical specifications.

Providing and applying required coat of water based Deep penetrating sealer on conrete surface,

27 NDSR beams columns, plasters walls, water tank etc.to react with cement and pentetrate in concrete to sqm 62.00 - 1050.00 65,100.00

make with intert to chlorides/chemical and act as water resistant.

Providing and fixing of Polycarbonate Sheet of 4MM Thick with all the fittings, plugs, sealers,

silicone filling Etc. as per direction of Engineer In Charge

29 NDSR Replacement of 4mm Polycarbonate Sheet sqm 30.00 - 3860.00 115,800.00

Painting with synthetic enamel paint of approved brand and manufacture of required colour to

give an even shade :

Two or more coats on new work over an under coat of suitable shade with ordinary paint of

approved brand and manufacture

Chequered terrazo tiles 22 mm thick with graded marble chips of size up to 6 mm in floors, jointed

31 11.19 with neat cement slurry mixed with pigment to match the shade of the tiles, including rubbing and

polishing complete, on 20 mm thick bed of cement mortar 1:4 (1 cement :4 coarse sand) :

11.19.3 Dark shade pigment using ordinary cement sqm 150.00 1442.15 216,322.50

Brick work with common burnt clay modular bricks of class designation

7.5 in foundation and plinth in:

6.2.1 Cement mortar 1:4 (1 cement : 4 coarse sand) Cum 1 6504.90 6,504.90

33.A BOUNDARY WALL :

Digitally signed by AMIT

Earth work in excavation by mechanical means (Hydraulic excavator)/manual means over

areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including getting

out and disposal of excavated earth lead upto 50 m and for all lift, as directed by Engineer-in

2.6.1 All kinds of soil Cum 27.90 177.50 4952.25

filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in

2.25 layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, Cum 10.00 196.00 1960.00

lead up to 50 and for all lift.

1:4:8 (1 cement : 4 coarse sand (zone-iii) derived from natural sources : 8 graded stone

aggregate 40 mm nominal size derived from natural sources)

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in

foundation and plinth in:

6.1.2 Cement mortar 1:6 (1 cement : 6 coarse sand Cum 8.75 7132.25 62407.19

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in

superstructure above plinth level up to floor V level in all shapes and sizes in

6.4.2 Cement mortar 1:6 (1 cement : 6 coarse sand) Cum 16.00 9105.95 145695.20

providing and laying in position ready mixed or site batched design mix cement concrete for

reinforced cement concrete work; using coarse aggregate and fine aggregate derived from natural

sources, portland pozzolana / ordinary portland /portland Slag cement, admixtures in

5.33 recommended proportions as per iS: 9103 to accelerate / retard setting of concrete, to improve

durability and workability without impairing strength; including pumping of concrete to site of

laying, curing, carriage for all leads; but excluding the cost of centering, shuttering, finishing and

reinforcement as per direction of the engineer-in-charge; for the following grades of concrete.

5.33.1 All works upto plinth level: concrete of m25 grade with minimum cement content of 330 kg /cum Cum 2.43 9504.75 23096.54

All works above plinth level upto floor V level: concrete of m25 grade with minimum cement

content of 330 kg /cum

Centering and shuttering including strutting, propping etc. and removal of form for foundations,

footings, bases of columns, etc. for mass concrete

5.9.6 columns, pillars, piers, Abutments, posts and Struts Sqm 23.9 961.30 22975.07

Steel reinforcement for r.c.c. work including straightening, cutting, bending, placing in

5.22.6 position and binding all complete upto plinth level.: thermo-mechanically treated bars of grade fe- Kg 515 107.85 55542.75

13.1.2 12 mm cement plaster of mix : 1:6 (1 cement: 6 fine sand) Sqm 140.00 333.35 46669.00

13.46 Finishing walls with Acrylic Smooth exterior paint of required shade :

New work (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior

primer applied @ 0.90 litre/10 sqm)

1:2:4 (1 cement : 2 coarse sand (zone-iii) derived from natural sources : 4 graded stone

aggregate 20 mm nominal size derived from natural sources)

Digitally signed by AMIT

33.B REPAIR OR GATE AND RAILING:

Steel work welded in built up sections/ framed work, including cutting, hoisting, fixing in position

and applying a priming coat of approved steel primer using structural steel etc. as required.

10.25.2 In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works Kg 400.00 172.60 69040.00

Painting with synthetic enamel paint of approved brand and manufacture of required colour to

13.62.1 give an even shade : 13.62.1 Two or more coats on new work over an under coat of suitable shade Sqm 180.00 226.25 40725.00

with ordinary paint of approved brand and manufacture

34 REPAIR OF ROAD AT SET BACK AREA

Repairing damaged and depressed portions of existing concrete passage/stilt parking flooring by

chipping loose concrete, cleaning surface, applying bonding agent and laying polymer modified

repair mortar/concrete, including finishing to match existing floor level and texture complete as

directed by Engineer-in-Charge.Assuming:

Average repair thickness = 20 mm

Polymer bonding agent (SBR/Latex based)

Polymer modified repair mortar (1:3 CM with additive or ready repair mortar) Includes chipping,

cleaning, labour, finishing and curing

Renovation of existing Security Guard Cabin including dismantling/removal of damaged plaster,

flooring, doors, windows and other deteriorated components; providing and laying new floor tiles,

wall putty and painting, repair of masonry and plaster, waterproofing treatment (where required),

replacement/repair of doors and windows, electrical wiring, switches, LED light fittings, fan point,

painting of grill/steel members, cleaning, finishing and all allied civil and electrical works complete

as directed by Engineer-in-Charge.

Demolishing cement concrete manually/ by mechanical means

36 15.2 including disposal of material within 50 metres lead as per direction

of Engineer - in - charge.

15.2.1 Nominal concrete 1:3:6 or richer mix (i/c equivalent design mix) cum 2.00 2434.25 4,868.50

Providing and laying in position cement concrete of specified grade

37 4.1 excluding the cost of centering and shuttering - All work up to plinth

1:2:4 (1 cement : 2 coarse sand (zone-III) derived from natural

4.1.3 sources : 4 graded stone aggregate 20 mm nominal size Cum 2.00 7878.50 15,757.00

derived from natural sources)

38 13.1.1 12 mm cement plaster of mix: 1:4 (1 cement: 4 fine sand) Sqm 13.00 347.05 4,511.65

Digitally signed by AMIT

Providing and laying rectified Glazed Ceramic floor tiles of size 300x300 mm or more

(thickness to be specified by the manufacturer), of 1st quality conforming to IS : 15622,

39 11.39 of approved make, in colours White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick Sqm 3.50 1330.00 4,655.00

cement mortar 1:4 (1 Cement: 4 Coarse sand), jointing with grey cement slurry @ 3.3 kg/

sqm including grouting the joints with white cement and matching pigments etc., complete

Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be

specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle

green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados,

over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey

cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of

matching shade complete.

Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation

as approved by Engineer-in-Charge) of total coated thickness 0.50mm (base metal of minimum

0.45mm thickness with total coating thickness of 0.05mm) with zinc coating 120 grams per sqm as

per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and

polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum

to avoid scratches during transportation and should be supplied in single length upto 12 metre or

as desired by Engineer-in-charge. The sheet shall be fixed using self drilling /self tapping screws of

size (5.5x 55 mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved

surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape

wherever required.

For Staff Toilet

Providing and fixing factory made panel PVC door shutter consisting of frame made out of M.S.

tubes of 19 gauge thickness and size of 19 mm x 19 mm for styles and 15x15 mm for top & bottom

rails. M.S. frame shall have a coat of steel primers of approved make and manufacture. M.S. frame

covered with 5 mm thick heat moulded PVC ‘C’ channel of size 30 mm thickness, 70 mm width out

of which 50 mm shall be flat and 20 mm shall be tapered in 45 degree angle on both side forming

styles and 5 mm thick, 95 mm wide PVC sheet out of which 75mm shall be flat and 20 mm shall be

tapered in 45 degree on the inner side to form top and bottom rail and 115 mm wide PVC sheet

42 9.120.2 out of which 75 mm shall be flat and 20 mm shall be tapered on both sides to form lock rail. Top, Sqm 2.00 3663.80 7,327.60

bottom and lock rails shall be provided both side of the panel. 10 mm (5 mm x 2 ) thick, 20 mm

wide cross PVC sheet be provided as gap insert for top rail & bottom rail, paneling of 5 mm thick

both side PVC sheet to be fitted in the M.S. frame welded/ sealed to the styles & rails with 7 mm (5

mm+2 mm) thick x 15 mm wide PVC sheet beading on inner side, and joined together with solvent

cement adhesive. An additional 5 mm thick PVC strip of 20 mm width is to be stuck on the interior

side of the ‘C’ Channel using PVC solvent adhesive etc. complete as per direction of Engineer-in-

charge, manufacturer’s specification & drawing: 30 mm thick pre laminated PVC door shutters.

Providing and fixing IS : 12817 marked stainless steel butt hinges (heavy weight) with stainless steel

screws etc. complete : 100x60x2.50 mm

Digitally signed by AMIT

Providing and fixing aluminium tower bolts, ISI marked, anodised (anodic coating not less

44 9.97.3 than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade, with Nos. 1.00 99.70 99.70

necessary screws etc. complete : 200x10 mm

Providing and fixing aluminium hanging floor door stopper, ISI marked, anodised (anodic coating

45 9.101.1 not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour and shade, with Nos. 1.00 39.60 39.60

necessary screws etc. complete: Single rubber stopper

Providing and fixing bright finished brass 100 mm mortice latch and lock, ISI marked, with six levers

46 9.103 and a pair of anodised (anodic coating not less than grade AC 10 as per IS : 1868) aluminium lever Nos. 1.00 868.95 868.95

handles of approved quality with necessary screws etc. complete.

Providing and fixing aluminium handles, ISI marked, anodised (anodic coating not less than grade

47 9.100.1 AC 10 as per IS : 1868) transparent or dyed to required colour or shade, with necessary screws etc. Nos. 2.00 66.25 132.50

complete : 125 mm

Providing and fixing SS/CP Brass Occupancy Indicator Bolt (Vacant/Engaged), SS screws, fasteners,

rawl plugs and all accessories complete for toilet door.

Providing and fixing white vitreous china European Water Closet (EWC), floor mounted/wall hung

type as specified, complete with soft close seat cover, flushing arrangement, flush pipe, connection

fittings, all accessories, cutting and making good the walls/floors wherever required, complete in

all respects as per direction of Engineer-in-Charge.

Providing and fixing white vitreous china wall hung water closet complete with soft close seat

50 MR cover, necessary brackets, connection fittings, waste pipe connection, testing and commissioning, Nos. 1.00 12500.00 12,500.00

including cutting and making good the walls/floors wherever required, complete in all respects.

Providing and fixing concealed/low level flushing cistern of with dual flush arrangement, flush

plate/operating lever, flush pipe, fittings, accessories and connections complete in all respects.

Providing and fixing white vitreous china wash basin including waste coupling, bottle trap, pair of

angle valves, flexible connections, brackets, fixing arrangement and all accessories complete.

Providing and fixing 5 mm thick superior quality mirror of size 600 mm × 450 mm with approved

frame/back support, screws, rawl plugs and all accessories complete.

Providing and fixing CP health faucet with 1.0 m long flexible tube, wall hook and all accessories

Providing and fixing CP brass bathroom accessories set comprising soap dish, towel ring and robe

hook of complete with screws and accessories.

Providing and fixing chromium plated brass pillar cock for wash basin, complete with all necessary

56 MR fittings, connections, testing and commissioning, including cutting and making good wherever Nos. 1.00 2000.00 2,000.00

Digitally signed by AMIT

Providing and fixing 15 mm dia CP brass angle valve with wall flange o, complete with all

accessories and connections.

Providing and fixing 15 mm dia concealed stop cock (heavy duty brass body) with CP operating

spindle, wall flange and all accessories complete,

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot &

cold water supply, including all CPVC plain & brass threaded fittings and fixing the pipe with clamps

at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and

the cost of cutting chases and making good the same including testing of joints complete as per

direction of Engineer in Charge. Concealed work, including cutting chases and making good the

walls etc : 15 mm nominal dia Pipes

60 18.8.3 20 mm nominal dia Pipes Metre 4.00 537.60 2,150.40

61 MR Providing and fixing CP brass pillar cock complete Nos. 1.00 2000.00 2,000.00

62 MR Providing and fixing 15 mm CP brass angle valve with flangecomplete Nos. 1.00 600.00 600.00

63 MR Providing and fixing 15 mm concealed stop cock with operating spindle and flange complete Nos. 1.00 - 1500.00 1,500.00

Providing and fixing trap of self cleansing design with screwed down or hinged grating with or

64 17.60.2 without vent arm complete, including cost of cutting and making good the walls and floors: 100 -

mm inlet and 75 mm outlet

17.60.2.1 Sand cast iron S&S as per IS - 398 Nos. 1.00 1975.15 1,975.15

Providing and fixing 75 mm dia UPVC SWR pipe conforming to IS 13592

(Supreme/Astral/Finolex/Prince or approved equivalent) including all fittings such as bends, tees,

offsets, door tees, access pieces, clamps, supports, solvent cement joints, cutting chases, making

good walls/floors and testing complete in all respects.

Providing and fixing 110 mm dia UPVC SWR pipe conforming to IS 13592

(Supreme/Astral/Finolex/Prince or approved equivalent) including all fittings such as bends, tees,

offsets, access pieces, clamps, supports, solvent cement joints, cutting chases, making good

walls/floors and testing complete in all respects.

Connecting newly installed sanitary/waste pipe system to the existing sewer line/manhole

including excavation, cutting existing pipe/manhole, providing necessary fittings, jointing materials,

testing, refilling, disposal of surplus earth and making good complete in all respects as directed by

Engineer-in-Charge.

MULTIPLYING FACTOR @0.973 FOR 18 % GST 3,055,741.96

Grand Total of Civil External Works 3,147,414.22 895,480.00

Grand Total of Civil External Works 3,147,414.22 895,480.00

Digitally signed by AMIT