Special Repair work at JNV Mayurbhanj, Odisha

Sl. No. Description Amount DSR Amount Non-DSR

1 Repair Work School Building-1 no. 46,30,769.46 26,574.27

2 Repair Work at Kitchen & Dining 11,24,365.49

3 Repair Work at M.P. Hall 12,09,299.41

4 Repair Work at 96 nos of boys unit 26,38,835.69

Repair Work at Boys Dormitory For 320 nos of

Repair Work at Girls Dormitory For 240 nos of

7 Repair Work at Principal Quarter 7,52,509.15

6 Repair Work at Staff Quarter 36,88,321.88

8 Repair Work at Group D Quarter 15,50,413.56

10 Repair Work at RCC Bed & Table 9,590.16

PRIME COST INCLUDING GST 2,48,98,597.16

Digitally signed by JAYA

COST ABSTRACT :- REPAIR WORK OF SCHOOL BUILDING - JNV, MAYURBHANJ, ODISHA

Amount on Amount on

Sl DSR Rate (In

Item Description Units Total Qty DSR - 2023 (In Non DSR

A. Structural Repair & Retrofitting

Reinforced cement concrete work in walls (any thickness), including

pilasters, buttresses, plinth and string courses, fillets, columns,

1 26.28 pillars, piers,

abutments, posts and struts etc. above plinth level up to floor five

level, excluding

cost of centering, shuttering, finishing and reinforcement :

A. 26.28.2 50mm average thickness Sqm 28.000 256.35 7177.800

B. 26.28.3 25 mm avarage thickness Sqm 37.800 126.75 4791.150

Cleaning of reinforcement from rust from the reinforcing bars to give

it a total rust free steel surface by using alkaline chemical rust

remover of approved make with paint brush and removing loose

particles after 24 hours of its application with wire brush and

washing with water and allowing it to dry, all complete as per

of Engineer-In-Charge.

26.29.1 Bars upto 12 mm diameter Mtr 1052.80 8.25 8685.600

Cleaning of exposed concrete surface of sticking material including

loose and foreign material by sand blasting with coarse sand followed

by and including cleaning with oil free air blast as per direction of

Engineer in charge.

Shotcreting R.C.C. columns, beams and slabs etc. in layers with

approved design mix concrete having the specified minimum

characteristic compressive strength [with ordinary portland cement,

4 26.38 coarse sand and graded stone aggregate of 10 mm maximum size

in proportion as per design criteria] including the cost of centering

and shuttering at edges and corners etc. as directed by Engineer in-

Note: Rates shall include the providing necessary ground wires etc.

The levelling gauges, if used, shall be paid for separately. Payment

under this item shall be made only after proper wet curing has been

done and surface has been satisfactorily evaluated by sounding/

tapping with a blunt metal instrument.

25mm thick in Grade M 25 with cement content not

less than 330 kg per cum

50mm thick in Grade M 25 with cement content not

less than 330 kg per cum

Providing and inserting 12mm dia galvanised steel injection nipple in

honey comb area and along crack line including drilling of holes of

required diametre (20mm to 30mm) up to depth from 30mm to

at required spacing and making the hole & crack dust free by blowing

compressed air, sealing the distance between injection nipple with

adhesive chemical of approved make and allow it to cure complete

as per direction of Engineer-In-Charge.

Providing and fixing hard drawn steel wire fabric of size 75 x25 mm

mesh or other suitable size wire mesh to be fixed & firmly anchored

6 26.40 to the concrete surface by means of "L" shaped mild steel shear key Sqm 82.720 902.55 74658.936

welded with existing reinforcement including the cost of materials,

labour, tool & plants as approved by Engineer-in-charge.

Repair to plaster of thickness 12 mm to 20 mm in patches with epoxy

based dampgaurd (Dr. Fixit Make) , including cutting the area of

plaster in proper shape, raking out joints and preparing and plastering

the durface of the walls complete, including disposal of rubbish to the

dumping ground, all complete as per direction of Engineer- in-Charge.

With cement mortar 1:4 (1cement: 4coarse sand)

Digitally signed by JAYA

Amount on Amount on

Sl DSR Rate (In

Item Description Units Total Qty DSR - 2023 (In Non DSR

Providing and applying white cement based putty of average thickness

8 13.80 1 mm, of approved brand and manufacturer, over the plastered wall Sqm 120.520 156.05 18807.146

surface to prepare the surface even and smooth complete.

Providing and fixing hand rail of approved size by welding etc. to steel

9 10.26 railing, balcony railing, staircase railing and similar works, including

priming coat of approved steel primer.

Structural Repair & Retrofitting Works Total : 7,45,652.08 -

Say (In Lakhs): 7.46 -

B. Repairs to Roof

Demolishing mud phaska in terracing and disposal of material within

50 metres lead.

Providing and laying APP (Atactic Polypropylene Polymer) modified

prefabricated five layer 3 mm thick water proofing membrane, black

reinforced with non-woven polyester matt consisting of a coat of

for bitumen membrane @ 0.40 litre/sqm by the same membrane

density at 25°C, 0.87-0.89 kg/ litre and viscocity 70-160 cps. Over

coat the layer of membrane shall be laid using Butane Torch and

joints etc, and preparing the surface complete. The vital physical and

parameters of the membrane shall be as under : Joint strength in

and transverse direction at 23°C as 650/ 450N/ 5cm. Tear strength

in longitudinal

and transverse direction as 300/250N. Softening point of membrane

than 150°C. Cold flexibility shall be upto -2°C when tested in

accordance with

ASTM, D - 5147. The laying of membrane shall be got done through

Extra for covering top of membrane with Geotextile 120 gsmnon

woven 100% polyster of thickness 1 to 1.25MM bnded to membrane

with intermittent touch by heating the membrane by Butane Torch as

per manufacturer recommendation

Repair to Roof Works Total : 16,24,324.30 -

Say (In Lakhs): 16.24 -

C. Repairs to Toilets

Demolishing R.C.C. work manually/ by mechanical means including

13 15.3 of steel bars and disposal of unserviceable material within 50 metres Cum 0.432 3551.25 1534.140

per direction of Engineer - in- charge.

Demolishing brick work manually/ by mechanical means including

14 15.7 serviceable material and disposal of unserviceable material within 50

lead as per direction of Engineer-in-charge.

15.7.4 In cement mortar Cum 7.121 2060.20 14670.272

Removing mortar from bricks and cleaning bricks including stacking

15 15.8 within a

lead of 50 m (stacks of cleaned bricks shall be measured):

15.8.3 From brick work in cement mortar Nos 1.673 6700.80 11213.038

Dismantling tile work in floors and roofs laid in cement mortar

16 15.23 including

stacking material within 50 metres lead.

15.23.1 For thickness of tiles 10 mm to 25 mm sqm 635.945 73.40 46678.392

Reinforced cement concrete work in walls (any thickness), including

attached pilasters, buttresses, plinth and string courses, fillets,

17 5.2 columns, pillars, piers, abutments, posts and struts etc. above plinth

level up to floor five level, excluding

cost of centering, shuttering, finishing and reinforcement :

1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) derived from natural

5.2.2 sources : 3 graded stone aggregate 20 mm nominal size derived from Cum 0.432 10852.95 4688.474

natural sources)

Centering and shuttering including strutting, propping etc. and

18 5.9 removal of form

for all heights:

5.9.16 Edges of slabs and breaks in floors and walls

Digitally signed by JAYA

Amount on Amount on

Sl DSR Rate (In

Item Description Units Total Qty DSR - 2023 (In Non DSR

Centering and shuttering including strutting, propping etc. and

19 5.9 removal of form

for all heights:

5.9.3 Suspended floors, roofs, landings, balconies and access platform Sqm 4.320 927.25 4005.720

Steel reinforcement for R.C.C. work including straightening, cutting,

bending, placing in position and binding all complete upto plinth level.

5.22.6 Thermo-Mechanically Treated bars of grade Fe-500D or more. Kg 33.912 107.85 3657.409

Brick work with common burnt clay F.P.S. (non modular) bricks of

21 6.4 designation 7.5 in superstructure above plinth level up to floor V

level in all shapes

6.4.2 Cement mortar 1:6 (1 cement : 6 coarse sand) Cum 5.962 9105.95 54286.032

Half brick masonry with common burnt clay F.P.S. (non modular)

bricks of class

designation 7.5 in superstructure above plinth level up to floor V

6.13.2 Cement mortar 1:4 (1 cement :4 coarse sand) Sqm 10.080 1123.80 11327.904

Extra for providing and placing in position 2 Nos 6mm dia. M.S. bars

third course of half brick masonry.

Providing and fixing Ist quality ceramic glazed wall tiles

conforming to IS: 15622 (thickness to be specified by the

manufacturer), of approved make, in all colours, shades except

burgundy, bottle green, black of any size as approved by

24 8.31 Engineer-in-Charge, in skirting, risers of steps and dados, over 12 sqm 305.058 1267.95 386798.291

mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand)

and jointing with grey cement slurry @ 3.3kg per sqm,

including pointing in white cement mixed with pigment of

Providing and laying Ceramic glazed floor tiles of size 300x300 mm

(thickness to be specified by the manufacturer) of 1st quality

to IS : 15622 of approved make in colours such as White, Ivory, Grey,

Fume Red Brown, laid on 20 mm thick cement mortar 1:4 (1 Cement

4 Coarse sand), Jointing with grey cement slurry @ 3.3 kg/sqm

pointing the joints with white cement and matching pigment etc.,

Providing and laying water proofing treatment to vertical and

26 22.30 horizontal surfaces of depressed portions of W.C., kitchen and the

like consisting of:

Ist course of applying cement slurry @ 4.4 kg/sqm mixed

with water proofing compound conforming to IS 2645 in

recommended proportions including rounding off junction of

vertical and horizontal surface.

IInd course of 20 mm cement plaster 1:3 (1 cement : 3 coarse

sand) mixed with water proofing compound in recommended

proportion including rounding off junction of vertical and

horizontal surface.

IIIrd course of applying blown or residual bitumen applied hot

at 1.7 kg. per sqm of area.

IVth course of 400 micron thick PVC sheet. (Overlaps at joints

of PVC sheet should be 100 mm wide and pasted to each sqm 104.086 769.60 80104.432

other with bitumen @ 1.7 kg/sqm).

Supply and filling od Cinder in sunkan portion of toilet area including

27 MR ramming etc including all labour and T&P etc complete as per Cum 12.173 2183.04 26574.274

direction of Engineer-in-charge.

Dismantling of flushing cistern of all types (C.I./PVC/Vitrious China)

28 15.52 including stacking of useful materials near the site and disposal of Each 5.000 112.05 560.250

unserviceable materials within 50 metres lead.

White Vitreous china Orissa pattern W.C. pan of size 580x440 mm

type foot rests

Digitally signed by JAYA

Amount on Amount on

Sl DSR Rate (In

Item Description Units Total Qty DSR - 2023 (In Non DSR

Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass

30 17.7 taps, 32 mm C.P. brass waste of standard pattern, including painting

and brackets, cutting and making good the walls wherever require:

White Vitreous China Flat back wash basin size 550x 400 mm with

15 mm C.P. brass pillar tap

Providing and fixing P.V.C. waste pipe for sink or wash basin including

waste fittings complete.

Providing and fixing 600x450 mm beveled edge mirror of superior

32 17.31 approved quality) complete with 6 mm thick hard board ground fixed Each 0.000 1607.95 0.000

cleats with C.P. brass screws and washers complete.

Providing and fixing white vitreous china flat back or wall corner type

33 17.23 front urinal basin of 430x260x350 mm and 340x410x265 mm sizes Each 3.000 1648.95 4946.850

Water Supply Installations

Dismantling G.I. pipes (external work) including excavation and

34 15.44 trenches after taking out the pipes, manually/ by mechanical means

including stacking of pipes within 50 metres lead as per direction of

Engineer-in-charge :

Dismantling C.I. pipes including excavation and refilling trenches after

taking out the pipes, manually/ by mechanical means breaking lead

35 15.45 joints, melting of lead and making into blocks including stacking of

& lead at site within 50 metre lead as per direction of Engineer-in-

Dismantling of C.I. sluice valve including stacking of useful materials

36 15.53 within

a lead of 50 metres

15.53.1 Up to 150 mm diameter Each 5.000 319.50 1597.500

37 17.35 Providing and fixing soil, waste and vent pipes :

38 17.35.1.2 100mm Centrifugally cast (spun) iron socket & spigot (S&S) pipe as per IS:

39 17.35.2.2 75mm Centrifugally cast (spun) iron socketed pipe as per IS: 3989 Mtr 75.000 1186.00 88950.000

Providing lead caulked joints to sand cast iron/centrifugally cast

40 17.58 (spun) iron pipes

and fittings of diameter :

Providing and fixing M.S. holder-bat clamps of approved design to

iron/cast iron (spun) pipe embedded in and including cement

concrete blocks

41 17.37 10x10x10 cm of 1:2:4 mix (1 cement : 2 coarse sand : 4 graded

stone aggregate

20 mm nominal size), including cost of cutting holes and making

Providing and fixing trap of self cleansing design with screwed down

42 17.60 grating with or without vent arm complete, including cost of cutting

good the walls and floors :

17.60.2.1 100mm inlet & 75mm outlet Sand cast iron S&S as per IS - 3989 Each 5.000 1975.15 9875.750

43 17.57 Providing and fixing collar :

17.57.1.2 100 mm Sand cast iron S&S as per IS - 3989 Each 15.000 513.15 7697.250

17.57.2.2 75 mm Sand cast iron S&S as per IS - 3989 Each 10.000 362.05 3620.500

44 17.39 Providing and fixing plain bend of required degree.

17.39.1.1 100 mm dia Sand cast iron S&S as per IS - 1729 Each 15.000 470.45 7056.750

17.39.2.2 75 mm dia Sand cast iron S&S as per IS - 3989 Each 10.000 390.50 3905.000

Digitally signed by JAYA

Amount on Amount on

Sl DSR Rate (In

Item Description Units Total Qty DSR - 2023 (In Non DSR

Providing and fixing bend of required degree with access door,

45 17.38 insertion rubber

washer 3 mm thick, bolts and nuts complete.

17.38.1.2 100 mm dia Sand cast iron S&S as per IS - 1729 Each 15.000 705.20 10578.000

17.38.2.2 75 mm dia Sand cast iron S&S as per IS - 3989 Each 10.000 522.80 5228.000

Providing and fixing single equal plain junction of required degree

46 17.43 with access

door, insertion rubber washer 3 mm thick, bolts and nuts complete.

17.43.1.1 100x100x100 mm Sand cast iron S&S as per IS - 1729 Each 15.000 726.55 10898.250

17.43.2.1 75x75x75 mm Sand cast iron S&S as per IS - 1729 Each 10.000 629.50 6295.000

47 17.56 Providing and fixing terminal guard :

17.56.1.2 100 mm dia Sand cast iron S&S as per IS - 1729 Each 15.000 506.00 7590.000

17.56.2.2 75 mm dia Sand cast iron S&S as per IS - 3989 Each 10.000 404.75 4047.500

48 17.29 Providing and fixing 100 mm sand cast Iron grating for gully trap. Each 10.000 53.25 532.500

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes,

thermal stability for hot & cold water supply, including all CPVC plain

threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing.

49 18.80 This includes

jointing of pipes & fittings with one step CPVC solvent cement and

cutting chases and making good the same including testing of joints

as per direction of Engineer in Charge.

Concealed work, including cutting chases and making good the walls

18.8.1 15 mm nominal dia Pipes Mtr 65.000 497.80 32357.000

18.8.2 20 mm nominal dia Pipes Mtr 45.000 537.60 24192.000

18.8.3 25 mm nominal dia Pipes Mtr 35.000 627.25 21953.750

18.8.4 32 mm nominal dia Pipes Mtr 40.000 739.30 29572.000

50 18.21 Providing and fixing uplasticised PVC connection pipe with brass unions :

51 18.21 Providing and fixing uplasticised PVC connection pipe with brass unions :

Providing and fixing C.P. brass bib cock of approved quality

52 18.49 conforming to

Providing and fixing C.P. brass long body bib cock of approved quality

conforming to IS standards and weighing not less than 690 gms.

Providing and fixing C.P. brass angle valve for basin mixer and geyser

54 18.53 points

of approved quality conforming to IS:8931

Providing and fixing ball valve (brass) of approved quality, High or low

pressure, with plastic floats complete :

Providing and fixing gun metal gate valve with C.I. wheel of approved

55 18.17 quality

(screwed end) :

Providing and fixing rectangular high density polyethylene water

loft tank with cover, conforming to ISI : 12701, colour of opaque

56 18.48 A approved by Engineer-in-charge. The rate includes making necessary Ltr 1000.000 11.00 11000.000

for inlet, outlet & over flow pipes. The base support i/c fittings &

tank shall be paid separately

57 18.16 Providing and fixing brass stop cock of approved quality :

Digitally signed by JAYA

Amount on Amount on

Sl DSR Rate (In

Item Description Units Total Qty DSR - 2023 (In Non DSR

Providing and fixing on wall face unplasticised Rigid PVC rain water

conforming to IS : 13592 Type A, including jointing with seal ring

IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single

socketed pipes.

Providing and fixing on wall face unplasticised - PVC moulded fittings/

accessories for unplasticised Rigid PVC rain water pipes conforming

13592 Type A, including jointing with seal ring conforming to IS :

10 mm gap for thermal expansion.

Total of sub-head (Water Supply Installations ) 6,36,212.50

EXTERNAL SEWERAGE SYSTEM

Taking out C.I. cover with frame from R.C.C. top slab of manholes of

sizes including demolishing of R.C.C. work manually/ by mechanical

and stacking of useful materials near the site and disposal of

materials within 50 metres lead as per direction of Engineer-in-

Dismantling of road gully chamber of various sizes including C.I.

with frame including stacking of useful materials near the site and

of unserviceable materials within 50 metres lead including refilling

Dismantling of manhole including R.C.C. top slab, C.I. cover with

62 19.24 including stacking of useful materials near the site and disposal of

unserviceable materials within 50 m lead as per direction of Engineer-

19.24.1 Rectangular manhole 90x80 cm and 45 cm deep Each 2.000 2540.85 5081.700

Raising manhole cover and frame slab to required level including

63 19.26 existing slab and making good the damage as required (Raising

manhole to be paid separately) :

Rectangular manhole 90x80 cm with rectangular cover 600 x 450 mm

Providing and fixing C.P. Brass extension nipple (size 15mmx50mm)

approved make and quality as per direction of Engineer-in-charge.

Providing and fixing PTMT extension nipple for water tank pipe,

65 18.75 fittings of

approved quality and colour.

18.75.3 25mm nominal bore, weighing not less than 62 gms Each 2.000 113.35 226.700

Making chases up to 7.5x7.5 cm in walls including making good and

with matching surface after housing G.I. pipe etc.

67 18.76 Cutting holes up to 30x30 cm in walls including making good the same:

18.76.1 With common burnt clay F.P.S. (non modular) bricks Each 10.000 416.80 4168.000

Constructing masonry Chamber 30x30x50 cm inside, in brick work in

mortar 1:4 (1 cement :4 coarse sand) for stop cock, with C. I.

100x100 x75 mm (inside) with hinged cover fixed in cement concrete

mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm

68 18.32 nominal

size), i/c necessary excavation, foundation concrete 1:5:10 ( 1

cement : 5 fine

sand : 10 graded stone aggregate 40mm nominal size ) and inside

with cement mortar 1:3 (1 cement : 3 coarse sand) 12mm thick,

finished with a

floating coat of neat cement complete as per standard design :

18.32.1 With common burnt clay F.P.S.(non modular) bricks of class designationEach

Digitally signed by JAYA

Amount on Amount on

Sl DSR Rate (In

Item Description Units Total Qty DSR - 2023 (In Non DSR

Constructing masonry Chamber 60x60x75 cm inside, in brick work in

mortar 1:4 (1 cement : 4 coarse sand) for sluice valve, with C.I.

100mm top diameter, 160 mm bottom diameter and 180 mm deep (

chained lid and RCC top slab 1:2:4 mix (1 cement : 2 coarse sand : 4

69 18.33 stone aggregate 20mm nominal size ) , i/c necessary excavation,

concrete 1:5:10 (1 cement : 5 fine sand : 10 graded stone aggregate

nominal size) and inside plastering with cement mortar 1:3 (1

cement : 3 coarse

sand) 12 mm thick, finished with a floating coat of neat cement

per standard design :

18.33.1 With common burnt clay F.P.S.(non modular) bricks of class designationEach

Total of sub-head (EXTERNAL SEWERAGE SYSTEM ) 49,280.05

Repairs to Toilets Works Total : 15,24,760.65 26,574.27

Say (In Lakhs): 15.25 0.27

D. Repair to Plinth Protection & Plaster Works

Dismantling old plaster or skirting raking out joints and cleaning the

surface for plaster including disposal of rubbish to the dumping

within 50 metres lead.

71 13.40 12 mm cement plaster of mix

72 13.50 15mm cement plaster on rough side of single or half brick wall of mix

73 13.16 6 mm cement plaster of mix

Repairs to plaster of thickness 12 mm to 20 mm in patches of area

2.5 sq.meters and under, including cutting the patch in proper shape,

74 14.10 raking out joints and preparing and plastering the surface of the walls

complete, including disposal of rubbish to the dumping ground, all

complete as per direction of Engineer-in-Charge.

14.1.2 With cement mortar 1:4 (1 cement: 4 coarse sand) Sqm 0.000 560.50 0.000

Removing dry or oil bound distemper, water proofing cement paint

75 13.91 and the like by scrapping, sand papering and preparing the surface Sqm 0.000 25.15 0.000

smooth including necessary repairs to scratches etc. complete.

Providing and applying white cement based putty of average thickness

76 13.80 1 mm, of approved brand and manufacturer, over the plastered wall Sqm 0.000 156.05 0.000

surface to prepare the surface even and smooth complete.

Distempering with 1st quality acrylic distember (Ready mix) having

77 13.41 content less than 50 grams/ litre of approved brand and

manufacture to give

an even shade :

New work (two or more coats) over and including water

thinnable priming coat with cement primer

Distempering with 1st quality acrylic distember (Ready mix) having

78 13.81.1 content less than 50 grams/ litre of approved brand and Sqm 0.000 62.70 0.000

manufacture including applying additional coats wherever required to

achieve even shade and colour Old work (one or more coats)

79 13.46 Finishing walls with Acrylic Smooth exterior paint of required shade :

New work (Two or more coat applied @ 1.67 ltr/10 sqm over and

13.46.1 including priming Sqm 0.000 160.60 0.000

coat of exterior primer applied @ 0.90 kg/10 sqm)

Removing white or colour wash by scrapping and sand papering and

the surface smooth including necessary repairs to scratches etc.

81 13.11 Finishing walls with Acrylic Smooth exterior paint of required shade :

Digitally signed by JAYA

Amount on Amount on

Sl DSR Rate (In

Item Description Units Total Qty DSR - 2023 (In Non DSR

Old work (Two or more coat applied @ 1.67 ltr/ 10 sqm) on existing

15 mm cement plaster on rough side of single or half brick wall of

13.5.2 1:6 (1 cement: 6 coarse sand) (Outer Plaster) Sqm 0.000 395.35 0.000

Add for plaster drip course/ groove in plastered surface or moulding

Making plinth protection 50mm thick of cement concrete 1:3:6 (1

cement : 3 coarse

sand (zone-III) derived from natural sources : 6 graded stone

aggregate 20 mm

nominal size derived from natural sources) over 75mm thick bed of

ballast 40 mm nominal size, well rammed and consolidated and

fine sand, including necessary excavation, levelling & dressing &

Repair to Plinth Protection & Plaster Works Total : - -

Say (In Lakhs): -

E. Repairs to Door/Windows

Dismantling doors, windows and clerestory windows (steel or wood)

85 15.12 including chowkhats, architrave, holdfasts etc. complete and stacking

50 metres lead :

15.12.1 Of area 3 sq. metres and below Nos 20.000 367.20 7344.000

86 14.9 Renewal of old putty of glass panes (length) Mtr 378.800 56.15 21269.620

Providing and fixing bright finished brass single acting spring hinges

necessary brass screws etc. complete :

Providing and fixing factory made single extruded WPC (Wood

Composite) solid plain flush door shutter of required size comprising

polymer of K value 58-60 (Suspension Grade), calcium carbonate and

fibers (wood powder/ rice husk/wheat husk) and non toxic additives

toxicity index of 12 for 100 gms) having minimum density of 650

screw withdrawal strength of 1800 N (Face) & 900 N (Edge),

compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2

resistance to spread of flame of Class A category with property of

termite/borer proof, water/moisture proof and fire retardant and

stainless steel butt hinges of required size with necessary full body

star headed counter sunk S.S screws, all as per direction of Engineer-

Providing and fixing wire gauge shutters using galvanized M.S. wire

of average width of aperture 1.4 mm in both directions with wire of

mm, for doors, windows and clerestory windows with hinges and

9.27.2 30 mm thick shutters

9.27.2.2 With ISI marked stainless steel butt hinges of required size

9.27.2.2.2 Kiln seasoned and chemically treated hollock wood Sqm 0.000 3447.80 0.000

Providing and fixing ISI marked oxidised M.S. sliding door bolts with

90 9.62 nuts and

screws etc. complete : (Copper oxidized as per IS 1378).

Providing and fixing ISI marked flush door shutter conforming to IS

:2202 (Part I) non decorative type, core of block board construction

with frame of 1st class hard wood and well matched commercial 3 ply

91 9.21.3 veneerong with vertical grains or cross bands and face veneers on Sqm 0.000 2093.70 0.000

both faces of shutters:25 mm thick (for cupboard) including ISI

marked niclel plated bright finished M.S. piano Hinges with necessary

Digitally signed by JAYA

Amount on Amount on

Sl DSR Rate (In

Item Description Units Total Qty DSR - 2023 (In Non DSR

Providing and fixing ISI marked oxidised M.S. tower bolt black finish,

type) with necessary screws etc. complete : (Copper oxidized as per

Providing and fixing aluminium handles, ISI marked, anodised

(anodic coating

93 9.100 not less than grade AC 10 as per IS : 1868) transparent or dyed to

colour or shade, with necessary screws etc. complete :

Providing and fixing aluminium hanging floor door stopper, ISI

marked, anodised

94 9.101 (anodic coating not less than grade AC 10 as per IS : 1868)

transparent or dyed

to required colour and shade, with necessary screws etc. complete.

9.101.2 Twin rubber stopper Nos 0.000 72.35 0.000

Providing and fixing 2nd class teak wood lipping/ moulded beading or

taj beading of size 18X5 mm fixed with wooden adhesive of approved

quality and screws/nails on the edges of the Pre-laminated particle

board as per direction of Engineer-in-charge.

Providing and fixing wooden moulded corner beading of triangular

96 9.111 the junction of panelling etc. with iron screws, plugs and priming coat

unexposed surface etc. complete 2nd class teak wood.

9.111.1 50x50 mm (base and height) Mtr 0.00 354.35 0.000

Providing and fixing magnetic catcher of approved quality in

97 9.114 cupboard / ward

robe shutters, including fixing with necessary screws etc. complete.

9.114.1 Triple strip vertical type Mtr 0.000 52.50 0.000

Providing and fixing wooden moulded beading to door and window

iron screws, plugs and priming coat on unexposed surface etc.

9.40.2 Kiln seasoned and chemically treated hollock wood

Providing and fixing ISI marked oxidised M.S. single acting spring

99 9.59 hinges with

necessary screws etc. complete. (Copper oxidized as per IS 1378).

Providing and fixing nickel plated M.S. pipe curtain rods with nickel

100 9.47 plated

Providing and fixing pressed steel door frames conforming to IS:

manufactured from commercial mild steel sheet of 1.60 mm

thickness, including

hinges, jamb, lock jamb, bead and if required angle threshold of mild

of section 50x25 mm, or base ties of 1.60 mm, pressed mild steel

101 10.14 welded or

rigidly fixed together by mechanical means, including M.S. pressed

2.5 mm thick with mortar guards, lock strike-plate and shock

specified and applying a coat of approved steel primer after pre-

the surface as directed by Engineer-in-charge:

Digitally signed by JAYA

Amount on Amount on

Sl DSR Rate (In

Item Description Units Total Qty DSR - 2023 (In Non DSR

Providing and fixing factory made ISI marked steel glazed doors,

ventilators, side /top /centre hung, with beading and all members

F7D,F4B, K11 B and K12 B etc. complete of standard rolled steel

sections, joints

mitred and flash butt welded and sash bars tenoned and riveted,

providing and fixing of hinges, pivots, including priming coat of

primer, but excluding the cost of other fittings, complete all as per

design, (sectional weight of only steel members shall be measured

Fixing with 15x3 mm lugs 10 cm long embedded in cement concrete

10.11.1 15x10x10 cm of C.C. 1:3:6 (1 Cement : 3 coarse sand : 6 graded Kg 633.600 131.05 83033.280

stone aggregate

20 mm nominal size) @22 Kg/Sqm

Providing and fixing M.S. grills of required pattern in frames of

103 9.48 with M.S. flats, square or round bars etc. including priming coat with

steel primer all complete.

9.48.2 Fixed to openings /wooden frames with rawl plugs screws etc. Kg 576.000 238.35 137289.600

Providing and fixing T-iron frames for doors, windows and ventilators

steel Tee-sections, joints mitred and welded, including fixing of

hinges and screws and applying a priming coat of approved steel

Fixing with 15x3 mm lugs 10 cm long embedded in cement concrete

10.13.1 15x10x10 cm of C.C. 1:3:6 (1 Cement : 3 coarse sand : 6 graded Kg 57.750 141.70 8183.175

stone aggregate

20 mm nominal size).

Providing and fixing oxidised M.S. casement stays (straight peg type)

necessary screws etc. complete. (Copper oxidized as per IS : 1378).

9.68.1 300 mm weighing not less than 330 grams Nos 10.000 67.40 674.000

9.68.2 250 mm weighing not less than 280 grams Nos 15.000 61.05 915.750

Providing & fixing glass panes with putty and glazing clips in steel

windows, clerestory windows, all complete with :

10.30.1 4.0 mm thick glass panes (weight not less than 10 kg/ sqm) Sqm 98.440 1390.15 136846.366

Providing and fixing PVC rigid foam sheet 1 mm thick on existing

(bathroom and W.C. doors) using synthetic rubber based adhesive.

108 13.50 Applying priming coat:

With ready mixed aluminum primer of approved brand and

manufacture on resinous wood and plywood

Painting with synthetic enamel paint of approved brand and

109 13.62 manufacture of

required colour to give an even shade :

Two or more coats on new work over an under coat of suitable shade

ordinary paint of approved brand and manufacture

Repairs to Door/Windows Works Total : 7,36,032.43 -

Say (In Lakhs): 7.36

F. Repairs to Flooring

Demolishing cement concrete manually/ by mechanical means

110 15.2 disposal of material within 50 metres lead as per direction of Engineer

15.2.2 Nominal concrete 1:4:8 or leaner mix (i/c equivalent design mix) Cum 0.000 1503.60 0.000

Providing and laying in position cement concrete of specified grade

111 4.1 excluding

the cost of centering and shuttering - All work up to plinth level :

1:5:10 (1 cement : 5 coarse sand (zone-III) derived from natural

stone aggregate 40 mm nominal size derived from natural sources

Digitally signed by JAYA

Amount on Amount on

Sl DSR Rate (In

Item Description Units Total Qty DSR - 2023 (In Non DSR

Providing and laying in position cement concrete of specified grade

112 4.1 excluding

the cost of centering and shuttering - All work up to plinth level :

1:2:4 (1 cement : 2 coarse sand (zone-III) derived from natural

4.1.3 sources : 4 graded Cum 0.000 7878.50 0.000

stone aggregate 20 mm nominal size derived from natural sources)

Kota stone slab flooring over 20 mm (average) thick base laid over

and jointed with grey cement slurry mixed with pigment to match the

shade of the slab, including rubbing and polishing complete with base

of cement mortar 1 : 4 (1 cement : 4 coarse sand) :

Kota stone slabs 20 mm thick in risers of steps, skirting, dado and

on 12 mm (average) thick cement mortar 1:3 (1 cement: 3 coarse

jointed with grey cement slurry mixed with pigment to match the

slabs, including rubbing and polishing complete.

Providing and laying Vitrified tiles in different sizes (thickness to be

specified by manufacturer), with water absorption less than 0.08 %

and conforming to I.S. 15622, of approved make, in all colours &

115 11.46 shade, in skirting, riser of steps, over 12 mm thick bed of cement

mortar 1:3 (1 cement: 3 coarse sand), jointing with grey cement

slurry @ 3.3 kg/ sqm including grouting the joint with white cement &

matching pigments etc. complete.

Marble stone flooring with 18 mm thick marble stone, as per sample

approved by Engineer-in-charge, over 20 mm (average) thick base of

116 11.23 cement

mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with grey

including rubbing and polishing complete with :

11.23.5 Udaipur green marble Sqm 0.000 2428.60 0.000

Cement concrete flooring 1:2:4 (1 cement : 2 coarse sand : 4 graded

117 11.3 aggregate) finished with a floating coat of neat cement, including

but excluding the cost of nosing of steps etc. complete.

11.3.1 40 mm thick with 20 mm nominal size stone aggregate Mtr 0.000 614.20 0.000

Repairs to Flooring Works Total : - -

Say (In Lakhs): -

Grand Total 46,57,343.73

Grand Total 46,57,343.73

Digitally signed by JAYA

COST ABSTRACT :- REPAIR WORK OF KITCHEN & DINING - JNV, MAYURBHANJ, ODISHA

Sl Rate (In Amount on DSR - on Non

DSR 2023 Item Description Units Total Qty

No Rs) 2023 (In Rs) DSR (In

A. Structural Repair & Retrofitting

Repair to plaster of thickness 12 mm to 20 mm in patches with epoxy based dampgaurd

(Dr. Fixit Make) , including cutting the area of plaster in proper shape, raking out joints

1 and preparing and plastering the durface of the walls complete, including disposal of Sqm 0.000 657.400 0.000

rubbish to the dumping ground, all complete as per direction of Engineer- in-Charge.

With cement mortar 1:4 (1cement: 4coarse sand)

Providing and applying white cement based putty of average thickness

2 13.80 1 mm, of approved brand and manufacturer, over the plastered wall Sqm 0.000 156.050 0.000

surface to prepare the surface even and smooth complete.

Structural Repair & Retrofitting Works Total : - -

Say (In Lakhs): - -

B. Repairs to Roof

Demolishing mud phaska in terracing and disposal of material within

50 metres lead.

Providing and laying APP (Atactic Polypropylene Polymer) modified

prefabricated five layer 3 mm thick water proofing membrane, black finished

reinforced with non-woven polyester matt consisting of a coat of bitumen primer

for bitumen membrane @ 0.40 litre/sqm by the same membrane manufacture of

density at 25°C, 0.87-0.89 kg/ litre and viscocity 70-160 cps. Over the primer

coat the layer of membrane shall be laid using Butane Torch and sealing all

4 14.91 joints etc, and preparing the surface complete. The vital physical and chemical

parameters of the membrane shall be as under : Joint strength in longitudinal

and transverse direction at 23°C as 650/ 450N/ 5cm. Tear strength in longitudinal

and transverse direction as 300/250N. Softening point of membrane not less

than 150°C. Cold flexibility shall be upto -2°C when tested in accordance with

ASTM, D - 5147. The laying of membrane shall be got done through the authorised

applicator of the manufacturer of membrane :

Extra for covering top of membrane with Geotextile 120 gsmnon woven 100% polyster

12 14.92 of thickness 1 to 1.25MM bnded to membrane with intermittent touch by heating the Sqm 396.59 88.90 35256.851

membrane by Butane Torch as per manufacturer recommendation

Providing and fixing precoated galvanised iron profile sheets (size, shape and

pitch of corrugation as approved by Engineer-in-charge) 0.50 mm (+ 0.05 %)

total coated thickness with zinc coating 120 grams per sqm as per IS: 277, in

240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and

polyester top coat 15-18 microns. Sheet should have protective guard film of 25

5 12.50 microns minimum to avoid scratches during transportation and should be Sqm 562.92 738.650 415797.312

supplied in single length upto 12 metre or as desired by Engineer-in-charge.

The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55

mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved

surfaces, excluding the cost of purlins, rafters and trusses and including cutting

to size and shape wherever required.

Providing and fixing false ceiling at all heights with integral densified calcium

silicate reinforced with fibre and natural filler false ceiling tiles of Size

595x595mm of approved texture, design and patterns as per CPWD

Specification 2019, to be laid in true horizontal level suspended on inter-locking

metal T-Grid of hot dipped galvanised iron section of 0.33mmthick (galvanized

@ 120 grams per sqm including both sides)comprising of main-T runners

of size 24x38 mm of length 3000 mm,cross - T of size 24x32 mm of length

1200 mm and secondaryintermediate cross-T of size 24x32 mm of length

600mm to formgrid module of size 600 x 600 mm, suspended from ceiling

6 26.22 usinggalvanised mild steel items (galvanizing @ 80 grams per sqm) i.e. 12x50

mm long dash fasteners, 6 mm dia fully threaded hanger rod upto 1000 mm

length and L-shape level adjuster of size 76x25x25x1.6 mm fixed with grid and

Z cleat of size 25x37x25x1.6mm thick with precut hole on both 25mm flange to

pierce into 12x50mm or even bigger size dash fastener if require, fixed with

Glavanised iron perimeter wall angle or size 24x24x0.40 mm of length 3000

mm to be fixed on periphey wall / partition with the help of plastic rawl plugs

at 450mm center to center and 40 mm long dry wall S.S screws. The workshall

be carried out as per specifications, drawing and as per directionsof the

Engineer-in-Charge.

26.22.1 With 15 mm thick Tegular edged light weight calcium sliciate false ceiling tiles Sqm 0.00 2207.000 0.000

Digitally signed by JAYA

Sl Rate (In Amount on DSR - on Non

DSR 2023 Item Description Units Total Qty

No Rs) 2023 (In Rs) DSR (In

Painting (one or more coats) on rain water, soil waste and vent pipes

7 13.96 and fittings with synthetic enamel paint of approved brand and

manufacture and required colour on old work :

13.96.2 100 mm diameter pipes Mtr 62.25 36.250 2256.563

Repair to Roof Works Total : 6,75,777.89 -

Say (In Lakhs): 6.76 -

C. Repairs to Toilets

Demolishing R.C.C. work manually/ by mechanical means including stacking of steel bars

8 15.3 and disposal of unserviceable material within 50 metres lead as per direction of Engineer - Cum 0.000 3551.250 0.000

Demolishing brick work manually/ by mechanical means including stacking of serviceable

9 15.7 material and disposal of unserviceable material within 50 metres lead as per direction of

Engineer-in-charge.

15.7.4 In cement mortar Cum 0.000 2060.200 0.000

Removing mortar from bricks and cleaning bricks including stacking within a lead of 50 m

(stacks of cleaned bricks shall be measured):

15.8.3 From brick work in cement mortar Nos 0.000 6700.800 0.000

Dismantling tile work in floors and roofs laid in cement mortar including

11 15.23 stacking material within 50 metres lead.

15.23.1 For thickness of tiles 10 mm to 25 mm sqm 0.000 73.40 0.000

Reinforced cement concrete work in walls (any thickness), including attached pilasters,

buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and

struts etc. above plinth level up to floor five level, excluding cost of centering, shuttering,

finishing and reinforcement :

1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) derived from natural sources : 3 graded

stone aggregate 20 mm nominal size derived from natural sources)

Centering and shuttering including strutting, propping etc. and removal of form for all

5.9.16 Edges of slabs and breaks in floors and walls

Centering and shuttering including strutting, propping etc. and removal of form for all

5.9.3 Suspended floors, roofs, landings, balconies and access platform Sqm 0.000 927.250 0.000

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in

position and binding all complete upto plinth level.

5.22.6 Thermo-Mechanically Treated bars of grade Fe-500D or more. Kg 0.000 107.850 0.000

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5

in superstructure above plinth level up to floor V level in all shapes and sizes in :

6.4.2 Cement mortar 1:6 (1 cement : 6 coarse sand) Cum 0.000 9105.950 0.000

Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class

designation 7.5 in superstructure above plinth level up to floor V level.

6.13.2 Cement mortar 1:4 (1 cement :4 coarse sand) Sqm 0.000 1123.800 0.000

Extra for providing and placing in position 2 Nos 6mm dia. M.S. bars at every third

course of half brick masonry.

Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622

(thickness to be specified by the manufacturer), of approved make, in all colours, shades

except burgundy, bottle green, black of any size as approved by Engineer-in-

Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar

19 8.31 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg sqm 0.000 1267.95 0.000

per sqm, including pointing in white cement mixed with pigment of matching

Providing and laying Ceramic glazed floor tiles of size 300x300 mm

(thickness to be specified by the manufacturer) of 1st quality conforming

to IS : 15622 of approved make in colours such as White, Ivory, Grey,

20 11.37 Fume Red Brown, laid on 20 mm thick cement mortar 1:4 (1 Cement : sqm 0.000 1096.550 0.000

4 Coarse sand), Jointing with grey cement slurry @ 3.3 kg/sqm including

pointing the joints with white cement and matching pigment etc.,

Dismantling of flushing cistern of all types (C.I./PVC/Vitrious China)

21 15.52 including stacking of useful materials near the site and disposal of Each 0.000 112.05 0.000

unserviceable materials within 50 metres lead.

White Vitreous china Orissa pattern W.C. pan of size 580x440 mm with integral

type foot rests

Digitally signed by JAYA

Sl Rate (In Amount on DSR - on Non

DSR 2023 Item Description Units Total Qty

No Rs) 2023 (In Rs) DSR (In

Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar

23 17.7 taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings

and brackets, cutting and making good the walls wherever require:

White Vitreous China Flat back wash basin size 550x 400 mm with single

15 mm C.P. brass pillar tap

Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C.

waste fittings complete.

Providing and fixing white vitreous china flat back or wall corner type lipped

front urinal basin of 430x260x350 mm and 340x410x265 mm sizes respectively

Water Supply Installations

Dismantling G.I. pipes (external work) including excavation and refilling

trenches after taking out the pipes, manually/ by mechanical means

including stacking of pipes within 50 metres lead as per direction of

Engineer-in-charge :

Dismantling C.I. pipes including excavation and refilling trenches after

taking out the pipes, manually/ by mechanical means breaking lead caulked

joints, melting of lead and making into blocks including stacking of pipes

& lead at site within 50 metre lead as per direction of Engineer-in-charge:

Dismantling of C.I. sluice valve including stacking of useful materials within

a lead of 50 metres

29 17.35 Providing and fixing soil, waste and vent pipes :

17.35.1.2 100mm Centrifugally cast (spun) iron socket & spigot (S&S) pipe as per IS: 3989 Mtr 45.000 1180.75 53133.750

17.35.2.2 75mm Centrifugally cast (spun) iron socketed pipe as per IS: 3989 Mtr 20.000 1186.00 23720.000

Providing lead caulked joints to sand cast iron/centrifugally cast (spun) iron pipes

and fittings of diameter :

Providing and fixing M.S. holder-bat clamps of approved design to Sand Cast

iron/cast iron (spun) pipe embedded in and including cement concrete blocks

31 17.37 10x10x10 cm of 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate

20 mm nominal size), including cost of cutting holes and making good the

Providing and fixing trap of self cleansing design with screwed down or hinged

32 17.60 grating with or without vent arm complete, including cost of cutting and making

good the walls and floors :

17.60.2.1 100mm inlet & 75mm outlet Sand cast iron S&S as per IS - 3989 Each 5.000 1975.15 9875.750

33 17.57 Providing and fixing collar :

17.57.1.2 100 mm Sand cast iron S&S as per IS - 3989 Each 15.000 513.15 7697.250

17.57.2.2 75 mm Sand cast iron S&S as per IS - 3989 Each 10.000 362.05 3620.500

34 17.39 Providing and fixing plain bend of required degree.

17.39.1.1 100 mm dia Sand cast iron S&S as per IS - 1729 Each 15.000 470.45 7056.750

17.39.2.2 75 mm dia Sand cast iron S&S as per IS - 3989 Each 10.000 390.50 3905.000

Providing and fixing bend of required degree with access door, insertion rubber

washer 3 mm thick, bolts and nuts complete.

17.38.1.2 100 mm dia Sand cast iron S&S as per IS - 1729 Each 15.000 705.20 10578.000

17.38.2.2 75 mm dia Sand cast iron S&S as per IS - 3989 Each 10.000 522.80 5228.000

Providing and fixing single equal plain junction of required degree with access

door, insertion rubber washer 3 mm thick, bolts and nuts complete.

17.43.1.1 100x100x100 mm Sand cast iron S&S as per IS - 1729 Each 15.000 726.55 10898.250

17.43.2.1 75x75x75 mm Sand cast iron S&S as per IS - 1729 Each 10.000 629.50 6295.000

37 17.56 Providing and fixing terminal guard :

17.56.1.2 100 mm dia Sand cast iron S&S as per IS - 1729 Each 15.000 506.00 7590.000

17.56.2.2 75 mm dia Sand cast iron S&S as per IS - 3989 Each 10.000 404.75 4047.500

38 17.29 Providing and fixing 100 mm sand cast Iron grating for gully trap. Each 10.000 53.25 532.500

Digitally signed by JAYA

Sl Rate (In Amount on DSR - on Non

DSR 2023 Item Description Units Total Qty

No Rs) 2023 (In Rs) DSR (In

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having

thermal stability for hot & cold water supply, including all CPVC plain & brass

threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes

jointing of pipes & fittings with one step CPVC solvent cement and the cost of

cutting chases and making good the same including testing of joints complete

as per direction of Engineer in Charge.

Concealed work, including cutting chases and making good the walls etc.

18.8.1 15 mm nominal dia Pipes Mtr 25.000 497.80 12445.000

18.8.2 20 mm nominal dia Pipes Mtr 35.000 537.60 18816.000

18.8.3 25 mm nominal dia Pipes Mtr 35.000 627.25 21953.750

18.8.4 32 mm nominal dia Pipes Mtr 40.000 739.30 29572.000

40 18.21 Providing and fixing uplasticised PVC connection pipe with brass unions :

41 18.21 Providing and fixing uplasticised PVC connection pipe with brass unions :

Providing and fixing C.P. brass bib cock of approved quality conforming to

Providing and fixing C.P. brass long body bib cock of approved quality

conforming to IS standards and weighing not less than 690 gms.

Providing and fixing C.P. brass angle valve for basin mixer and geyser points

of approved quality conforming to IS:8931

Providing and fixing ball valve (brass) of approved quality, High or low

pressure, with plastic floats complete :

Providing and fixing gun metal gate valve with C.I. wheel of approved quality

(screwed end) :

Providing and fixing rectangular high density polyethylene water storage

loft tank with cover, conforming to ISI : 12701, colour of opaque white or as

47 18.48 A approved by Engineer-in-charge. The rate includes making necessary holes Ltr 1000.000 11.00 11000.000

for inlet, outlet & over flow pipes. The base support i/c fittings & fixtures for

tank shall be paid separately

48 18.16 Providing and fixing brass stop cock of approved quality :

Providing and fixing on wall face unplasticised Rigid PVC rain water pipes

49 12.41 conforming to IS : 13592 Type A, including jointing with seal ring conforming to

IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes.

Providing and fixing on wall face unplasticised - PVC moulded fittings/

accessories for unplasticised Rigid PVC rain water pipes conforming to IS :

13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving

10 mm gap for thermal expansion.

Providing and fixing C.P. Brass extension nipple (size 15mmx50mm) of

approved make and quality as per direction of Engineer-in-charge.

Providing and fixing PTMT extension nipple for water tank pipe, fittings of

approved quality and colour.

18.75.3 25mm nominal bore, weighing not less than 62 gms Each 2.000 113.35 226.700

Total of sub-head (Water Supply Installations ) 3,48,412.40 -

EXTERNAL SEWERAGE SYSTEM

Digitally signed by JAYA

Sl Rate (In Amount on DSR - on Non

DSR 2023 Item Description Units Total Qty

No Rs) 2023 (In Rs) DSR (In

Taking out C.I. cover with frame from R.C.C. top slab of manholes of various

sizes including demolishing of R.C.C. work manually/ by mechanical means

and stacking of useful materials near the site and disposal of unserviceable

materials within 50 metres lead as per direction of Engineer-in-charge.

Dismantling of road gully chamber of various sizes including C.I. grating

with frame including stacking of useful materials near the site and disposal

of unserviceable materials within 50 metres lead including refilling the

Dismantling of manhole including R.C.C. top slab, C.I. cover with frame,

55 19.24 including stacking of useful materials near the site and disposal of

unserviceable materials within 50 m lead as per direction of Engineer-in-charge:

19.24.1 Rectangular manhole 90x80 cm and 45 cm deep Each 2.000 2540.85 5081.700

Raising manhole cover and frame slab to required level including dismantling

56 19.26 existing slab and making good the damage as required (Raising depth of

manhole to be paid separately) :

Rectangular manhole 90x80 cm with rectangular cover 600 x 450 mm of grade

Making chases up to 7.5x7.5 cm in walls including making good and finishing

with matching surface after housing G.I. pipe etc.

58 18.76 Cutting holes up to 30x30 cm in walls including making good the same:

18.76.1 With common burnt clay F.P.S. (non modular) bricks Each 5.000 416.80 2084.000

Cutting holes up to 15x15 cm in R.C.C. floors and roofs for passing drain pipe

etc. and repairing the hole after insertion of drain pipe etc. with cement concrete

1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal

size), including finishing complete so as to make it leak proof.

Constructing masonry Chamber 30x30x50 cm inside, in brick work in cement

mortar 1:4 (1 cement :4 coarse sand) for stop cock, with C. I. surface box

100x100 x75 mm (inside) with hinged cover fixed in cement concrete slab 1:2:4

mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal

size), i/c necessary excavation, foundation concrete 1:5:10 ( 1 cement : 5 fine

sand : 10 graded stone aggregate 40mm nominal size ) and inside plastering

with cement mortar 1:3 (1 cement : 3 coarse sand) 12mm thick, finished with a

floating coat of neat cement complete as per standard design :

18.32.1 With common burnt clay F.P.S.(non modular) bricks of class designation 7.5 Each 5.000 1992.60 9963.000

Constructing masonry Chamber 60x60x75 cm inside, in brick work in cement

mortar 1:4 (1 cement : 4 coarse sand) for sluice valve, with C.I. surface box

100mm top diameter, 160 mm bottom diameter and 180 mm deep ( inside) with

chained lid and RCC top slab 1:2:4 mix (1 cement : 2 coarse sand : 4 graded

61 18.33 stone aggregate 20mm nominal size ) , i/c necessary excavation, foundation

concrete 1:5:10 (1 cement : 5 fine sand : 10 graded stone aggregate 40 mm

nominal size) and inside plastering with cement mortar 1:3 (1 cement : 3 coarse

sand) 12 mm thick, finished with a floating coat of neat cement complete as

per standard design :

18.33.1 With common burnt clay F.P.S.(non modular) bricks of class designation 7.5 Each 2.000 10862.40 21724.800

Total of sub-head (EXTERNAL SEWERAGE SYSTEM ) 73,359.75

Repairs to Toilets Works Total : 4,27,914.50 -

Say (In Lakhs): 4.28 -

D. Repair to Plinth Protection & Plaster Works

Dismantling old plaster or skirting raking out joints and cleaning the

62 15.56 surface for plaster including disposal of rubbish to the dumping ground Sqm 0.000 54.65 0.000

within 50 metres lead.

63 13.40 12 mm cement plaster of mix

64 13.50 15mm cement plaster on rough side of single or half brick wall of mix

Digitally signed by JAYA

Sl Rate (In Amount on DSR - on Non

DSR 2023 Item Description Units Total Qty

No Rs) 2023 (In Rs) DSR (In

65 13.16 6 mm cement plaster of mix

Repairs to plaster of thickness 12 mm to 20 mm in patches of area

2.5 sq.meters and under, including cutting the patch in proper shape,

66 14.1 raking out joints and preparing and plastering the surface of the walls

complete, including disposal of rubbish to the dumping ground, all

complete as per direction of Engineer-in-Charge.

14.1.2 With cement mortar 1:4 (1 cement: 4 coarse sand) Sqm 0.000 560.500 0.000

Removing dry or oil bound distemper, water proofing cement paint

67 13.91 and the like by scrapping, sand papering and preparing the surface Sqm 0.000 25.15 0.000

smooth including necessary repairs to scratches etc. complete.

Providing and applying white cement based putty of average thickness

68 13.80 1 mm, of approved brand and manufacturer, over the plastered wall Sqm 0.000 156.05 0.000

surface to prepare the surface even and smooth complete.

Distempering with oil bound washable distemper of approved brand

and manufacture to give an even shade :

New work (two or more coats) over and including water

thinnable priming coat with cement primer

Distempering with 1st quality acrylic distember (Ready mix) having VOC

content less than 50 grams/ litre of approved brand and manufacture including applying

additional coats wherever required to achieve even shade and colour Old work (one or

71 13.46 Finishing walls with Acrylic Smooth exterior paint of required shade :

New work (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming

coat of exterior primer applied @ 0.90 kg/10 sqm)

Removing white or colour wash by scrapping and sand papering and preparing

the surface smooth including necessary repairs to scratches etc. complete

73 13.11 Finishing walls with Acrylic Smooth exterior paint of required shade :

Old work (Two or more coat applied @ 1.67 ltr/ 10 sqm) on existing cement

74 13.5 15 mm cement plaster on rough side of single or half brick wall of mix:

13.5.2 1:6 (1 cement: 6 coarse sand) (Outer Plaster) Sqm 0.000 395.35 0.000

Making plinth protection 50mm thick of cement concrete 1:3:6 (1 cement : 3 coarse

sand (zone-III) derived from natural sources : 6 graded stone aggregate 20 mm

nominal size derived from natural sources) over 75mm thick bed of dry brick

ballast 40 mm nominal size, well rammed and consolidated and grouted with

fine sand, including necessary excavation, levelling & dressing & finishing the

Repair to Plinth Protection & Plaster Works Total : - -

Say (In Lakhs): -

E. Repairs to Door/Windows

Dismantling doors, windows and clerestory windows (steel or wood) shutter

76 15.12 including chowkhats, architrave, holdfasts etc. complete and stacking within

50 metres lead :

15.12.1 Of area 3 sq. metres and below Nos 2.000 367.20 734.400

Digitally signed by JAYA

Sl Rate (In Amount on DSR - on Non

DSR 2023 Item Description Units Total Qty

No Rs) 2023 (In Rs) DSR (In

Providing and fixing factory made single extruded WPC (Wood Polymer

Composite) solid plain flush door shutter of required size comprising of virgin

polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural

fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum

toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and

screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum

77 26.87 compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and

resistance to spread of flame of Class A category with property of being

termite/borer proof, water/moisture proof and fire retardant and fixing with

stainless steel butt hinges of required size with necessary full body threaded

star headed counter sunk S.S screws, all as per direction of Engineer-In

Charge. (Note: stainless steel butt hinges and necessary S.S screws shall be

paid separately)

Providing and fixing wire gauge shutters using galvanized M.S. wire gauge

of average width of aperture 1.4 mm in both directions with wire of dia 0.63

mm, for doors, windows and clerestory windows with hinges and necessary

9.27.2 30 mm thick shutters

9.27.2.2 With ISI marked stainless steel butt hinges of required size

9.27.2.2.2 Kiln seasoned and chemically treated hollock wood Sqm 0.000 3447.800 0.000

Providing and fixing ISI marked oxidised M.S. sliding door bolts with nuts and

screws etc. complete : (Copper oxidized as per IS 1378).

Providing and fixing ISI marked oxidised M.S. tower bolt black finish, (Barrel

type) with necessary screws etc. complete : (Copper oxidized as per IS : 1378).

Providing and fixing aluminium handles, ISI marked, anodised (anodic coating

81 9.100 not less than grade AC 10 as per IS : 1868) transparent or dyed to required

colour or shade, with necessary screws etc. complete :

Providing and fixing aluminium hanging floor door stopper, ISI marked, anodised

82 9.101 (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed

to required colour and shade, with necessary screws etc. complete.

9.101.2 Twin rubber stopper Nos 0.000 72.350 0.000

Providing and fixing wooden moulded beading to door and window frames with

iron screws, plugs and priming coat on unexposed surface etc. complete :

9.40.2 Kiln seasoned and chemically treated hollock wood

Providing and fixing ISI marked oxidised M.S. single acting spring hinges with

necessary screws etc. complete. (Copper oxidized as per IS 1378).

Providing and fixing pressed steel door frames conforming to IS: 4351,

manufactured from commercial mild steel sheet of 1.60 mm thickness, including

hinges, jamb, lock jamb, bead and if required angle threshold of mild steel angle

of section 50x25 mm, or base ties of 1.60 mm, pressed mild steel welded or

rigidly fixed together by mechanical means, including M.S. pressed butt hinges

2.5 mm thick with mortar guards, lock strike-plate and shock absorbers as

specified and applying a coat of approved steel primer after pre-treatment of

the surface as directed by Engineer-in-charge:

Digitally signed by JAYA

Sl Rate (In Amount on DSR - on Non

DSR 2023 Item Description Units Total Qty

No Rs) 2023 (In Rs) DSR (In

Providing and fixing factory made ISI marked steel glazed doors, windows and

ventilators, side /top /centre hung, with beading and all members such as

F7D,F4B, K11 B and K12 B etc. complete of standard rolled steel sections, joints

86 10.11 mitred and flash butt welded and sash bars tenoned and riveted, including

providing and fixing of hinges, pivots, including priming coat of approved steel

primer, but excluding the cost of other fittings, complete all as per approved

design, (sectional weight of only steel members shall be measured for payment).

Fixing with 15x3 mm lugs 10 cm long embedded in cement concrete block

10.11.1 15x10x10 cm of C.C. 1:3:6 (1 Cement : 3 coarse sand : 6 graded stone aggregate Kg 0.000 131.050 0.000

20 mm nominal size) @22 Kg/Sqm

Providing and fixing M.S. grills of required pattern in frames of windows etc.

87 9.48 with M.S. flats, square or round bars etc. including priming coat with approved

steel primer all complete.

9.48.2 Fixed to openings /wooden frames with rawl plugs screws etc. Kg 0.000 238.350 0.000

Providing and fixing T-iron frames for doors, windows and ventilators of mild

88 10.13 steel Tee-sections, joints mitred and welded, including fixing of necessary butt

hinges and screws and applying a priming coat of approved steel primer.

Fixing with 15x3 mm lugs 10 cm long embedded in cement concrete block

10.13.1 15x10x10 cm of C.C. 1:3:6 (1 Cement : 3 coarse sand : 6 graded stone aggregate Kg 0.000 141.700 0.000

20 mm nominal size).

Providing and fixing oxidised M.S. casement stays (straight peg type) with

necessary screws etc. complete. (Copper oxidized as per IS : 1378).

9.68.1 300 mm weighing not less than 330 grams Nos 0.000 67.400 0.000

9.68.2 250 mm weighing not less than 280 grams Nos 0.000 61.050 0.000

Providing & fixing glass panes with putty and glazing clips in steel doors,

windows, clerestory windows, all complete with :

10.30.1 4.0 mm thick glass panes (weight not less than 10 kg/ sqm) Sqm 0.000 1390.150 0.000

91 14.9 Renewal of old putty of glass panes Mtr 0.000 56.150 0.000

92 13.50 Applying priming coat:

With ready mixed aluminum primer of approved brand and manufacture on resinous

wood and plywood

Painting with synthetic enamel paint of approved brand and manufacture of

required colour to give an even shade :

Two or more coats on new work over an under coat of suitable shade with

ordinary paint of approved brand and manufacture

Providing and fixing bright finished brass single acting spring hinges with

necessary brass screws etc. complete :

Providing and fixing PVC rigid foam sheet 1 mm thick on existing door shutters

(bathroom and W.C. doors) using synthetic rubber based adhesive.

Repairs to Door/Windows Works Total : 20,673.10 -

Say (In Lakhs): 0.21

F. Repairs to Flooring

Demolishing cement concrete manually/ by mechanical means including

96 15.2 disposal of material within 50 metres lead as per direction of Engineer - in

15.2.2 Nominal concrete 1:4:8 or leaner mix (i/c equivalent design mix) Cum 0.000 1503.600 0.000

Kota stone slab flooring over 20 mm (average) thick base laid over and jointed

with grey cement slurry mixed with pigment to match the shade of the slab,

including rubbing and polishing complete with base of cement mortar 1 : 4 (1

cement : 4 coarse sand) :

Kota stone slabs 20 mm thick in risers of steps, skirting, dado and pillars laid

on 12 mm (average) thick cement mortar 1:3 (1 cement: 3 coarse sand) and

jointed with grey cement slurry mixed with pigment to match the shade of the

slabs, including rubbing and polishing complete.

Digitally signed by JAYA

Sl Rate (In Amount on DSR - on Non

DSR 2023 Item Description Units Total Qty

No Rs) 2023 (In Rs) DSR (In

Marble stone flooring with 18 mm thick marble stone, as per sample of marble

approved by Engineer-in-charge, over 20 mm (average) thick base of cement

mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with grey cement slurry,

including rubbing and polishing complete with :

11.23.5 Udaipur green marble Sqm 0.000 2428.600 0.000

Repairs to Flooring Works Total : - -

Say (In Lakhs): -

Grand Total 11,24,365.49 -

Grand Total 11,24,365.49 -

Digitally signed by JAYA

COST ABSTRACT :- REPAIR WORK OF M.P. HALL - JNV, MAYURBHANJ, ODISHA

Amount on Amount on

Sl DSR Unit Rate (In

Item Description Total Qty DSR - 2023 (In Non DSR

A. Structural Repair & Retrofitting

Repair to plaster of thickness 12 mm to 20 mm in patches with epoxy

based dampgaurd (Dr. Fixit Make) , including cutting the area of

plaster in proper shape, raking out joints and preparing and plastering

the durface of the walls complete, including disposal of rubbish to the

dumping ground, all complete as per direction of Engineer- in-Charge.

With cement mortar 1:4 (1cement: 4coarse sand)

Providing and applying white cement based putty of average thickness

2 13.80 1 mm, of approved brand and manufacturer, over the plastered wall Sqm 0.000 156.050 0.000

surface to prepare the surface even and smooth complete.

Structural Repair & Retrofitting Works Total : - -

Say (In Lakhs): - -

B. Repairs to Roof

Demolishing mud phaska in terracing and disposal of material within

50 metres lead.

Providing and laying APP (Atactic Polypropylene Polymer) modified

prefabricated five layer 3 mm thick water proofing membrane, black

reinforced with non-woven polyester matt consisting of a coat of

for bitumen membrane @ 0.40 litre/sqm by the same membrane

density at 25°C, 0.87-0.89 kg/ litre and viscocity 70-160 cps. Over

coat the layer of membrane shall be laid using Butane Torch and

4 14.91 joints etc, and preparing the surface complete. The vital physical and

parameters of the membrane shall be as under : Joint strength in

and transverse direction at 23°C as 650/ 450N/ 5cm. Tear strength in

and transverse direction as 300/250N. Softening point of membrane

than 150°C. Cold flexibility shall be upto -2°C when tested in

accordance with

ASTM, D - 5147. The laying of membrane shall be got done through

Extra for covering top of membrane with Geotextile 120 gsmnon

woven 100% polyster of thickness 1 to 1.25MM bnded to membrane

with intermittent touch by heating the membrane by Butane Torch as

per manufacturer recommendation

Dismantling cement asbestos or other hard board ceiling or partition

5 15.41 including stacking of serviceable materials and disposal of Sqm 598.85 56.350 33745.198

materials within 50 metres lead.

Providing and fixing precoated galvanised iron profile sheets (size,

pitch of corrugation as approved by Engineer-in-charge) 0.50 mm (+

total coated thickness with zinc coating 120 grams per sqm as per IS:

240 mpa steel grade, 5-7 microns epoxy primer on both side of the

polyester top coat 15-18 microns. Sheet should have protective guard

6 12.50 microns minimum to avoid scratches during transportation and should Sqm 598.85 738.650 442340.553

supplied in single length upto 12 metre or as desired by Engineer-in-

The sheet shall be fixed using self drilling /self tapping screws of size

mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or

surfaces, excluding the cost of purlins, rafters and trusses and

including cutting

to size and shape wherever required.

Digitally signed by JAYA

Amount on Amount on

Sl DSR Unit Rate (In

Item Description Total Qty DSR - 2023 (In Non DSR

Providing and fixing false ceiling at all height including providing and

fixing of frame work made of special sections, power pressed from

M.S. sheets and galvanized with zinc coating of 120 gms/sqm (both

side inclusive) as per IS : 277 and consisting of angle cleats of size 25

mm wide x 1.6 mm thick with flanges of 27 mm and 37mm, at 1200

mm centre to centre, one flange fixed to the ceiling with dash fastener

12.5 mm dia x 50mm long with 6mm dia bolts, other flange of cleat

fixed to the angle hangers of 25x10x0.50 mm of required length with

nuts & bolts of required size and other end of angle hanger fixed with

intermediate G.I. channels 45x15x0.9 mm running at the spacing of

1200 mm centre to centre, to which the ceiling section 0.5 mm thick

7 12.45 bottom wedge of 80 mm with tapered flanges of 26 mm each having

lips of 10.5 mm, at 450 mm centre to centre, shall be fixed in a

direction perpendicular to G.I. intermediate channel with connecting

clips made out of 2.64 mm dia x 230 mm long G.I. wire at every

junction, including fixing perimeter channels 0.5 mm thick 27 mm high

having flanges of 20 mm and 30 mm long, the perimeter of ceiling

fixed to wall/partition with the help of rawl plugs at 450 mm centre,

with 25mm long dry wall screws @ 230 mm interval, including fixing of

gypsum board to ceiling section and perimeter channel with the help of

dry wall screws of size 3.5 x 25 mm at 230 mm c/c, including jointing

and finishing to a flush finish of tapered and square edges of the board

with recommended jointing compound , jointing tapes , finishing with

12.5 mm thick tapered edge gypsum plain board conforming to IS:

:2011 (Board with BIS certification marks)

Repair to Roof Works Total : 5,88,241.41 -

Say (In Lakhs): 5.88 -

C. Repairs to Toilets

Dismantling tile work in floors and roofs laid in cement mortar

8 15.23 including

stacking material within 50 metres lead.

15.23.1 For thickness of tiles 10 mm to 25 mm Sqm 173.958 73.40 12768.517

Providing and fixing Ist quality ceramic glazed wall tiles

conforming to IS: 15622 (thickness to be specified by the

manufacturer), of approved make, in all colours, shades except

burgundy, bottle green, black of any size as approved by

8 8.31 Engineer-in-Charge, in skirting, risers of steps and dados, over 12 sqm 168.510 1267.95 213662.255

mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand)

and jointing with grey cement slurry @ 3.3kg per sqm, including

pointing in white cement mixed with pigment of matching shade

Providing and laying Ceramic glazed floor tiles of size 300x300 mm

(thickness to be specified by the manufacturer) of 1st quality

to IS : 15622 of approved make in colours such as White, Ivory, Grey,

9 11.37 Fume Red Brown, laid on 20 mm thick cement mortar 1:4 (1 Cement : sqm 5.448 1096.550 5974.004

4 Coarse sand), Jointing with grey cement slurry @ 3.3 kg/sqm

pointing the joints with white cement and matching pigment etc.,

White Vitreous china Orissa pattern W.C. pan of size 580x440 mm

type foot rests

Providing and fixing P.V.C. waste pipe for sink or wash basin including

waste fittings complete.

Providing and fixing 600x450 mm beveled edge mirror of superior

12 17.31 approved quality) complete with 6 mm thick hard board ground fixed Each 0.000 1607.95 0.000

cleats with C.P. brass screws and washers complete.

Water Supply Installations

Dismantling G.I. pipes (external work) including excavation and

15.44 trenches after taking out the pipes, manually/ by mechanical means

including stacking of pipes within 50 metres lead as per direction of

Engineer-in-charge :

15.44.1 15 mm to 40 mm nominal bore Mtr 66 149.80 9909.270

Digitally signed by JAYA

Amount on Amount on

Sl DSR Unit Rate (In

Item Description Total Qty DSR - 2023 (In Non DSR

Dismantling C.I. or asbestos rain water pipe with fittings and clamps

15.42 including

stacking the material within 50 metres lead :

17.35 Providing and fixing soil, waste and vent pipes :

17.35.1.2 100mm Centrifugally cast (spun) iron socket & spigot (S&S) pipe as per IS:

17.35.2.2 75mm Centrifugally cast (spun) iron socketed pipe as per IS: 3989 Mtr 13.000 1186.00 15418.000

Providing lead caulked joints to sand cast iron/centrifugally cast (spun)

17.58 iron pipes

and fittings of diameter :

Providing and fixing M.S. holder-bat clamps of approved design to

iron/cast iron (spun) pipe embedded in and including cement concrete

17.37 10x10x10 cm of 1:2:4 mix (1 cement : 2 coarse sand : 4 graded

stone aggregate

20 mm nominal size), including cost of cutting holes and making good

Providing and fixing trap of self cleansing design with screwed down or

17.60 grating with or without vent arm complete, including cost of cutting

good the walls and floors :

17.60.2.1 100mm inlet & 75mm outlet Sand cast iron S&S as per IS - 3989 Each 4.000 1975.15 7900.600

17.57 Providing and fixing collar :

17.57.1.2 100 mm Sand cast iron S&S as per IS - 3989 Each 2.000 513.15 1026.300

17.57.2.2 75 mm Sand cast iron S&S as per IS - 3989 Each 2.000 362.05 724.100

17.39 Providing and fixing plain bend of required degree.

17.39.1.1 100 mm dia Sand cast iron S&S as per IS - 1729 Each 14.000 470.45 6586.300

17.39.2.2 75 mm dia Sand cast iron S&S as per IS - 3989 Each 7.000 390.50 2733.500

Providing and fixing bend of required degree with access door,

17.38 insertion rubber

washer 3 mm thick, bolts and nuts complete.

17.38.1.2 100 mm dia Sand cast iron S&S as per IS - 1729 Each 14.000 705.20 9872.800

17.38.2.2 75 mm dia Sand cast iron S&S as per IS - 3989 Each 7.000 522.80 3659.600

Providing and fixing single equal plain junction of required degree with

door, insertion rubber washer 3 mm thick, bolts and nuts complete.

17.43.1.1 100x100x100 mm Sand cast iron S&S as per IS - 1729 Each 14.000 726.55 10171.700

17.43.2.1 75x75x75 mm Sand cast iron S&S as per IS - 1729 Each 7.000 629.50 4406.500

17.56 Providing and fixing terminal guard :

17.56.1.2 100 mm dia Sand cast iron S&S as per IS - 1729 Each 14.000 506.00 7084.000

17.56.2.2 75 mm dia Sand cast iron S&S as per IS - 3989 Each 7.000 404.75 2833.250

17.29 Providing and fixing 100 mm sand cast Iron grating for gully trap. Each 4.000 53.25 213.000

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes,

thermal stability for hot & cold water supply, including all CPVC plain

threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing.

18.80 This includes

jointing of pipes & fittings with one step CPVC solvent cement and the

cutting chases and making good the same including testing of joints

as per direction of Engineer in Charge.

Concealed work, including cutting chases and making good the walls

18.8.1 15 mm nominal dia Pipes Mtr 40.000 497.80 19912.000

18.8.2 20 mm nominal dia Pipes Mtr 30.000 537.60 16128.000

18.8.3 25 mm nominal dia Pipes Mtr 129.500 627.25 81228.875

18.8.4 32 mm nominal dia Pipes Mtr 60.000 739.30 44358.000

18.21 Providing and fixing uplasticised PVC connection pipe with brass unions :

Providing and fixing C.P. brass bib cock of approved quality

18.49 conforming to

Digitally signed by JAYA

Amount on Amount on

Sl DSR Unit Rate (In

Item Description Total Qty DSR - 2023 (In Non DSR

Providing and fixing C.P. brass long body bib cock of approved quality

conforming to IS standards and weighing not less than 690 gms.

Providing and fixing C.P. brass angle valve for basin mixer and geyser

of approved quality conforming to IS:8931

18.53.1 15mm nominal bore Each 4.000 574.30 2297.200

Providing and fixing ball valve (brass) of approved quality, High or low

pressure, with plastic floats complete :

18.18.3 25 mm nominal bore Each 2.000 464.05 928.100

Providing and fixing gun metal gate valve with C.I. wheel of approved

(screwed end) :

Providing and placing on terrace (at all floor levels) polyethylene water

storage tank, IS : 12701 marked, with cover and suitable locking

and making necessary holes for inlet, outlet and overflow pipes but

fittings and the base support for tank.

Total of sub-head (Water Supply Installations ) 3,20,150.96

Repairs to Toilets Works Total : 5,66,329.63 -

Say (In Lakhs): 5.66 -

D. Repair to Plinth Protection & Plaster Works

Dismantling old plaster or skirting raking out joints and cleaning the

13 15.56 surface for plaster including disposal of rubbish to the dumping ground Sqm 0.000 54.65 0.000

within 50 metres lead.

14 13.50 15mm cement plaster on rough side of single or half brick wall of mix

15 13.16 6 mm cement plaster of mix

Removing dry or oil bound distemper, water proofing cement paint

16 13.91 and the like by scrapping, sand papering and preparing the surface Sqm 0.000 25.15 0.000

smooth including necessary repairs to scratches etc. complete.

Distempering with 1st quality acrylic distember (Ready mix) having

17 13.81.1 content less than 50 grams/ litre of approved brand and manufacture Sqm 0.000 62.70 0.000

including applying additional coats wherever required to achieve even

shade and colour Old work (one or more coats)

Removing white or colour wash by scrapping and sand papering and

the surface smooth including necessary repairs to scratches etc.

19 13.11 Finishing walls with Acrylic Smooth exterior paint of required shade :

Old work (Two or more coat applied @ 1.67 ltr/ 10 sqm) over and

including priming coat of exterior primer applied @ 2.20 kg/10 sqm)

Repair to Plinth Protection & Plaster Works Total : - -

Say (In Lakhs): -

E. Repairs to Door/Windows

Dismantling doors, windows and clerestory windows (steel or wood)

19 15.12 including chowkhats, architrave, holdfasts etc. complete and stacking

50 metres lead :

15.12.1 Of area 3 sq. metres and below Nos 0.000 367.20 0.000

Providing and fixing T-iron frames for doors, windows and ventilators

steel Tee-sections, joints mitred and welded, including fixing of

hinges and screws and applying a priming coat of approved steel

Digitally signed by JAYA

Amount on Amount on

Sl DSR Unit Rate (In

Item Description Total Qty DSR - 2023 (In Non DSR

Fixing with 15x3 mm lugs 10 cm long embedded in cement concrete

10.13.1 15x10x10 cm of C.C. 1:3:6 (1 Cement : 3 coarse sand : 6 graded Kg 0.000 141.700 0.000

stone aggregate

20 mm nominal size).

Providing and fixing pressed steel door frames conforming to IS: 4351,

manufactured from commercial mild steel sheet of 1.60 mm

thickness, including

hinges, jamb, lock jamb, bead and if required angle threshold of mild

of section 50x25 mm, or base ties of 1.60 mm, pressed mild steel

rigidly fixed together by mechanical means, including M.S. pressed

2.5 mm thick with mortar guards, lock strike-plate and shock

specified and applying a coat of approved steel primer after pre-

the surface as directed by Engineer-in-charge:

Providing and fixing factory made ISI marked steel glazed doors,

ventilators, side /top /centre hung, with beading and all members

F7D,F4B, K11 B and K12 B etc. complete of standard rolled steel

sections, joints

mitred and flash butt welded and sash bars tenoned and riveted,

providing and fixing of hinges, pivots, including priming coat of

primer, but excluding the cost of other fittings, complete all as per

design, (sectional weight of only steel members shall be measured for

Fixing with 15x3 mm lugs 10 cm long embedded in cement concrete

10.11.1 15x10x10 cm of C.C. 1:3:6 (1 Cement : 3 coarse sand : 6 graded Kg 0.000 131.050 0.000

stone aggregate

20 mm nominal size) @22 Kg/Sqm

Providing and fixing M.S. grills of required pattern in frames of

23 9.48 with M.S. flats, square or round bars etc. including priming coat with

steel primer all complete.

9.48.2 Fixed to openings /wooden frames with rawl plugs screws etc. Kg 0.000 238.350 0.000

Providing and fixing factory made single extruded WPC (Wood Polymer

Composite) solid plain flush door shutter of required size comprising

polymer of K value 58-60 (Suspension Grade), calcium carbonate and

fibers (wood powder/ rice husk/wheat husk) and non toxic additives

toxicity index of 12 for 100 gms) having minimum density of 650

screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum

compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2

resistance to spread of flame of Class A category with property of

termite/borer proof, water/moisture proof and fire retardant and

stainless steel butt hinges of required size with necessary full body

star headed counter sunk S.S screws, all as per direction of Engineer-

Charge. (Note: stainless steel butt hinges and necessary S.S screws

paid separately)

Providing and fixing ISI marked oxidised M.S. sliding door bolts with

25 9.62 nuts and

screws etc. complete : (Copper oxidized as per IS 1378).

Providing and fixing ISI marked oxidised M.S. tower bolt black finish,

type) with necessary screws etc. complete : (Copper oxidized as per

Digitally signed by JAYA

Amount on Amount on

Sl DSR Unit Rate (In

Item Description Total Qty DSR - 2023 (In Non DSR

Providing and fixing aluminium handles, ISI marked, anodised (anodic

27 9.100 not less than grade AC 10 as per IS : 1868) transparent or dyed to

colour or shade, with necessary screws etc. complete :

Providing and fixing aluminium hanging floor door stopper, ISI

marked, anodised

28 9.101 (anodic coating not less than grade AC 10 as per IS : 1868)

transparent or dyed

to required colour and shade, with necessary screws etc. complete.

9.101.2 Twin rubber stopper Each 0.000 72.350 0.000

29 13.50 Applying priming coat:

With ready mixed aluminum primer of approved brand and

manufacture on resinous wood and plywood

With ready mixed red oxide zinc chromate primer of approved brand

manufacture on steel galvanised iron/ steel works

Painting with synthetic enamel paint of approved brand and

31 13.62 manufacture of

required colour to give an even shade :

Two or more coats on new work over an under coat of suitable shade

ordinary paint of approved brand and manufacture

Providing & fixing glass panes with putty and glazing clips in steel

windows, clerestory windows, all complete with :

10.30.1 Float glass panes of thickness 4 mm Sqm 0.000 1064.650 0.000

Repairs to Door/Windows Works Total : 54,728.37 -

Say (In Lakhs): 0.55

F. Repairs to Flooring

Demolishing cement concrete manually/ by mechanical means

33 15.2 disposal of material within 50 metres lead as per direction of Engineer -

15.2.2 Nominal concrete 1:4:8 or leaner mix (i/c equivalent design mix) Cum 0.000 1503.600 0.000

Providing and laying in position cement concrete of specified grade

34 4.1 excluding

the cost of centering and shuttering - All work up to plinth level :

1:5:10 (1 cement : 5 coarse sand (zone-III) derived from natural

stone aggregate 40 mm nominal size)

Kota stone slab flooring over 20 mm (average) thick base laid over and

with grey cement slurry mixed with pigment to match the shade of

including rubbing and polishing complete with base of cement mortar

cement : 4 coarse sand) :

Kota stone slabs 20 mm thick in risers of steps, skirting, dado and

on 12 mm (average) thick cement mortar 1:3 (1 cement: 3 coarse

jointed with grey cement slurry mixed with pigment to match the

slabs, including rubbing and polishing complete.

Repairs to Flooring Works Total : - -

Say (In Lakhs): -

Grand Total 12,09,299.41 -

Grand Total 12,09,299.41 -

Digitally signed by JAYA

COST ABSTRACT :- REPAIR WORK OF 0.5 UNIT FOR 96 nos OF BOYS - JNV, MAYURBHANJ, ODISHA

Sl DSR Rate (In Amount on DSR -

Item Description Units Total Qty Non DSR

A. Structural Repair & Retrofitting

B. Repairs to Roof

Painting (one or more coats) on rain water, soil waste and vent pipes

1 13.96 and fittings with synthetic enamel paint of approved brand and

manufacture and required colour on old work :

13.96.2 100 mm diameter pipes Mtr 0.00 88.900 0.000

Repair to Roof Works Total : - -

Say (In Lakhs): - -

C. Repairs to Toilets

Demolishing cement concrete manually/ by mechanical means

2 15.2 disposal of material within 50 metres lead as per direction of Engineer

15.2.2 Nominal concrete 1:4:8 or leaner mix (i/c equivalent design mix) Cum 2.194 10852.950 23808.659

Demolishing R.C.C. work manually/ by mechanical means including

3 15.3 of steel bars and disposal of unserviceable material within 50 metres Cum 0.336 3551.250 1193.220

per direction of Engineer - in- charge.

Demolishing brick work manually/ by mechanical means including

4 15.7 serviceable material and disposal of unserviceable material within 50

lead as per direction of Engineer-in-charge.

15.7.4 In cement mortar Cum 4.140 2060.200 8529.228

Removing mortar from bricks and cleaning bricks including stacking

5 15.8 within a

lead of 50 m (stacks of cleaned bricks shall be measured):

15.8.3 From brick work in cement mortar Nos 0.973 6700.800 6519.208

Dismantling tile work in floors and roofs laid in cement mortar

6 15.23 including

stacking material within 50 metres lead.

15.23.1 For thickness of tiles 10 mm to 25 mm Sqm 627.61 73.40 46066.904

Providing and laying in position cement concrete of specified grade

7 4.1 excluding

the cost of centering and shuttering - All work up to plinth level :

1:5:10 (1 cement : 5 coarse sand (zone-III) derived from natural

stone aggregate 40 mm nominal size derived from natural sources)

Providing and laying in position cement concrete of specified grade

8 4.1 excluding

the cost of centering and shuttering - All work up to plinth level :

4.1.3 1:2:4 (1 cement : 2 coarse sand (zone-III) derived from natural sources Cum 1.463 7878.500 11522.306

Reinforced cement concrete work in walls (any thickness), including

pilasters, buttresses, plinth and string courses, fillets, columns,

9 5.2 pillars, piers,

abutments, posts and struts etc. above plinth level up to floor five

level, excluding

cost of centering, shuttering, finishing and reinforcement :

1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) derived from natural

5.2.2 sources : 3 graded stone aggregate 20 mm nominal size derived from Cum 0.336 10852.950 3646.591

natural sources)

Centering and shuttering including strutting, propping etc. and removal

10 5.9 of form

for all heights:

5.9.16 Edges of slabs and breaks in floors and walls

Centering and shuttering including strutting, propping etc. and removal

11 5.9 of form

for all heights:

5.9.3 Suspended floors, roofs, landings, balconies and access platform Sqm 3.360 927.250 3115.560

Steel reinforcement for R.C.C. work including straightening, cutting,

bending, placing in position and binding all complete upto plinth level.

5.22.6 Thermo-Mechanically Treated bars of grade Fe-500D or more. Kg 26.376 107.850 2844.652

Brick work with common burnt clay F.P.S. (non modular) bricks of

13 6.4 designation 7.5 in superstructure above plinth level up to floor V level

6.4.2 Cement mortar 1:6 (1 cement : 6 coarse sand) Cum 2.981 9105.950 27143.016

Digitally signed by JAYA

Sl DSR Rate (In Amount on DSR -

Item Description Units Total Qty Non DSR

Half brick masonry with common burnt clay F.P.S. (non modular)

14 6.13 bricks of class

designation 7.5 in superstructure above plinth level up to floor V level.

6.13.2 Cement mortar 1:4 (1 cement :4 coarse sand) Sqm 10.080 1123.800 11327.904

Extra for providing and placing in position 2 Nos 6mm dia. M.S. bars at

third course of half brick masonry.

Providing and fixing Ist quality ceramic glazed wall tiles

conforming to IS: 15622 (thickness to be specified by the

manufacturer), of approved make, in all colours, shades except

burgundy, bottle green, black of any size as approved by

16 8.31 Engineer-in-Charge, in skirting, risers of steps and dados, over 12 sqm 520.155 1267.95 659530.532

mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand)

and jointing with grey cement slurry @ 3.3kg per sqm, including

pointing in white cement mixed with pigment of matching shade

Providing and laying Ceramic glazed floor tiles of size 300x300 mm

(thickness to be specified by the manufacturer) of 1st quality

to IS : 15622 of approved make in colours such as White, Ivory, Grey,

17 11.37 Fume Red Brown, laid on 20 mm thick cement mortar 1:4 (1 Cement : sqm 107.460 1096.550 117834.715

4 Coarse sand), Jointing with grey cement slurry @ 3.3 kg/sqm

pointing the joints with white cement and matching pigment etc.,

Dismantling of flushing cistern of all types (C.I./PVC/Vitrious China)

18 15.52 including stacking of useful materials near the site and disposal of Each 5.000 112.05 560.250

unserviceable materials within 50 metres lead.

White Vitreous china Orissa pattern W.C. pan of size 580x440 mm

type foot rests

Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass

20 17.7 taps, 32 mm C.P. brass waste of standard pattern, including painting

and brackets, cutting and making good the walls wherever require:

White Vitreous China Flat back wash basin size 550x 400 mm with

15 mm C.P. brass pillar tap

Providing and fixing P.V.C. waste pipe for sink or wash basin including

waste fittings complete.

Providing and fixing 600x450 mm beveled edge mirror of superior

22 17.31 approved quality) complete with 6 mm thick hard board ground fixed Each 0.000 1607.95 0.000

cleats with C.P. brass screws and washers complete.

Providing and fixing white vitreous china flat back or wall corner type

23 17.23 front urinal basin of 430x260x350 mm or340x410x265 mm sizes Each 3.000 1648.95 4946.850

Providing and fixing PTMT towel rail complete with brackets fixed to

24 17.73 cleats with CP brass screws with concealed fittings arrangement of

quality and colour.

600 mm long towel rail with total length of 645 mm, width 78 mm and

height of 88 mm, weighing not less than 190 gms.

Water Supply Installations

Dismantling G.I. pipes (external work) including excavation and

25 15.44 trenches after taking out the pipes, manually/ by mechanical means

including stacking of pipes within 50 metres lead as per direction of

Engineer-in-charge :

Digitally signed by JAYA

Sl DSR Rate (In Amount on DSR -

Item Description Units Total Qty Non DSR

Dismantling C.I. pipes including excavation and refilling trenches after

taking out the pipes, manually/ by mechanical means breaking lead

26 15.45 joints, melting of lead and making into blocks including stacking of

& lead at site within 50 metre lead as per direction of Engineer-in-

Dismantling of flushing cistern of all types (C.I./PVC/Vitrious China)

27 15.52 including stacking of useful materials near the site and disposal of Each 5.000 112.05 560.250

unserviceable materials within 50 metres lead.

Dismantling of C.I. sluice valve including stacking of useful materials

28 15.53 within

a lead of 50 metres

15.53.1 Up to 150 mm diameter Each 5.000 319.50 1597.500

29 17.35 Providing and fixing soil, waste and vent pipes :

17.35.1.2 100mm Centrifugally cast (spun) iron socket & spigot (S&S) pipe as per IS:Mtr

17.35.2.2 75mm Centrifugally cast (spun) iron socketed pipe as per IS: 3989 Mtr 85.000 1186.00 100810.000

Providing lead caulked joints to sand cast iron/centrifugally cast (spun)

30 17.58 iron pipes

and fittings of diameter :

Providing and fixing M.S. holder-bat clamps of approved design to

iron/cast iron (spun) pipe embedded in and including cement concrete

31 17.37 10x10x10 cm of 1:2:4 mix (1 cement : 2 coarse sand : 4 graded

stone aggregate

20 mm nominal size), including cost of cutting holes and making good

Providing and fixing trap of self cleansing design with screwed down or

32 17.60 grating with or without vent arm complete, including cost of cutting

good the walls and floors :

17.60.2.1 100mm inlet & 75mm outlet Sand cast iron S&S as per IS - 3989 Each 5.000 1975.15 9875.750

33 17.57 Providing and fixing collar :

17.57.1.2 100 mm Sand cast iron S&S as per IS - 3989 Each 38.000 513.15 19499.700

17.57.2.2 75 mm Sand cast iron S&S as per IS - 3989 Each 48.000 362.05 17378.400

34 17.39 Providing and fixing plain bend of required degree.

17.39.1.1 100 mm dia Sand cast iron S&S as per IS - 1729 Each 38.000 470.45 17877.100

17.39.2.2 75 mm dia Sand cast iron S&S as per IS - 3989 Each 48.000 390.50 18744.000

Providing and fixing bend of required degree with access door,

35 17.38 insertion rubber

washer 3 mm thick, bolts and nuts complete.

17.38.1.2 100 mm dia Sand cast iron S&S as per IS - 1729 Each 38.000 705.20 26797.600

17.38.2.2 75 mm dia Sand cast iron S&S as per IS - 3989 Each 48.000 522.80 25094.400

Providing and fixing single equal plain junction of required degree with

36 17.43 access

door, insertion rubber washer 3 mm thick, bolts and nuts complete.

17.43.1.1 100x100x100 mm Sand cast iron S&S as per IS - 1729 Each 38.000 726.55 27608.900

17.43.2.1 75x75x75 mm Sand cast iron S&S as per IS - 1729 Each 48.000 629.50 30216.000

37 17.56 Providing and fixing terminal guard :

17.56.1.2 100 mm dia Sand cast iron S&S as per IS - 1729 Each 38.000 506.00 19228.000

17.56.2.2 75 mm dia Sand cast iron S&S as per IS - 3989 Each 48.000 404.75 19428.000

38 17.29 Providing and fixing 100 mm sand cast Iron grating for gully trap. Each 10.000 53.25 532.500

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes,

thermal stability for hot & cold water supply, including all CPVC plain

threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing.

39 18.80 This includes

jointing of pipes & fittings with one step CPVC solvent cement and the

cutting chases and making good the same including testing of joints

as per direction of Engineer in Charge.

Concealed work, including cutting chases and making good the walls

18.8.1 15 mm nominal dia Pipes Mtr 60.000 497.80 29868.000

18.8.2 20 mm nominal dia Pipes Mtr 75.000 537.60 40320.000

18.8.3 25 mm nominal dia Pipes Mtr 80.000 627.25 50180.000

18.8.4 32 mm nominal dia Pipes Mtr 65.000 739.30 48054.500

Digitally signed by JAYA

Sl DSR Rate (In Amount on DSR -

Item Description Units Total Qty Non DSR

40 18.21 Providing and fixing uplasticised PVC connection pipe with brass unions :

41 18.21 Providing and fixing uplasticised PVC connection pipe with brass unions :

Providing and fixing C.P. brass bib cock of approved quality

42 18.49 conforming to

Providing and fixing C.P. brass long body bib cock of approved quality

conforming to IS standards and weighing not less than 690 gms.

Providing and fixing C.P. brass angle valve for basin mixer and geyser

44 18.53 points

of approved quality conforming to IS:8931

18.53.1 15mm nominal bore Each 5.000 574.30 2871.500

Providing and fixing ball valve (brass) of approved quality, High or low

pressure, with plastic floats complete :

18.18.3 25 mm nominal bore Each 2.000 464.05 928.100

Providing and fixing gun metal gate valve with C.I. wheel of approved

46 18.17 quality

(screwed end) :

Providing and fixing rectangular high density polyethylene water

loft tank with cover, conforming to ISI : 12701, colour of opaque

47 18.48 A approved by Engineer-in-charge. The rate includes making necessary Ltr 4500.000 11.00 49500.000

for inlet, outlet & over flow pipes. The base support i/c fittings &

tank shall be paid separately

18.16 Providing and fixing brass stop cock of approved quality :

Providing and fixing on wall face unplasticised Rigid PVC rain water

conforming to IS : 13592 Type A, including jointing with seal ring

IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single

socketed pipes.

Providing and fixing on wall face unplasticised - PVC moulded fittings/

accessories for unplasticised Rigid PVC rain water pipes conforming to

13592 Type A, including jointing with seal ring conforming to IS :

10 mm gap for thermal expansion.

Total of sub-head (Water Supply Installations ) 8,34,272.65

EXTERNAL SEWERAGE SYSTEM

Taking out C.I. cover with frame from R.C.C. top slab of manholes of

sizes including demolishing of R.C.C. work manually/ by mechanical

and stacking of useful materials near the site and disposal of

materials within 50 metres lead as per direction of Engineer-in-

Dismantling of road gully chamber of various sizes including C.I.

with frame including stacking of useful materials near the site and

of unserviceable materials within 50 metres lead including refilling the

Dismantling of manhole including R.C.C. top slab, C.I. cover with

52 19.24 including stacking of useful materials near the site and disposal of

unserviceable materials within 50 m lead as per direction of Engineer-

19.24.1 Rectangular manhole 90x80 cm and 45 cm deep Each 2.000 2540.85 5081.700

Digitally signed by JAYA

Sl DSR Rate (In Amount on DSR -

Item Description Units Total Qty Non DSR

Raising manhole cover and frame slab to required level including

53 19.26 existing slab and making good the damage as required (Raising depth

manhole to be paid separately) :

Rectangular manhole 90x80 cm with rectangular cover 600 x 450 mm

Providing and fixing C.P. Brass extension nipple (size 15mmx50mm)

approved make and quality as per direction of Engineer-in-charge.

Providing and fixing PTMT extension nipple for water tank pipe,

55 18.75 fittings of

approved quality and colour.

18.75.3 25mm nominal bore, weighing not less than 62 gms Each 2.000 113.35 226.700

Making chases up to 7.5x7.5 cm in walls including making good and

with matching surface after housing G.I. pipe etc.

57 18.76 Cutting holes up to 30x30 cm in walls including making good the same:

18.76.1 With common burnt clay F.P.S. (non modular) bricks Each 6.000 416.80 2500.800

Cutting holes up to 15x15 cm in R.C.C. floors and roofs for passing

etc. and repairing the hole after insertion of drain pipe etc. with

58 18.77 cement concrete Each 12.000 452.00 5424.000

1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm

size), including finishing complete so as to make it leak proof.

Constructing masonry Chamber 30x30x50 cm inside, in brick work in

mortar 1:4 (1 cement :4 coarse sand) for stop cock, with C. I. surface

100x100 x75 mm (inside) with hinged cover fixed in cement concrete

mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm

59 18.32 nominal

size), i/c necessary excavation, foundation concrete 1:5:10 ( 1

cement : 5 fine

sand : 10 graded stone aggregate 40mm nominal size ) and inside

with cement mortar 1:3 (1 cement : 3 coarse sand) 12mm thick,

finished with a

floating coat of neat cement complete as per standard design :

18.32.1 With common burnt clay F.P.S.(non modular) bricks of class designation 7.5

Constructing masonry Chamber 60x60x75 cm inside, in brick work in

mortar 1:4 (1 cement : 4 coarse sand) for sluice valve, with C.I.

100mm top diameter, 160 mm bottom diameter and 180 mm deep (

chained lid and RCC top slab 1:2:4 mix (1 cement : 2 coarse sand : 4

60 18.33 stone aggregate 20mm nominal size ) , i/c necessary excavation,

concrete 1:5:10 (1 cement : 5 fine sand : 10 graded stone aggregate

nominal size) and inside plastering with cement mortar 1:3 (1 cement

sand) 12 mm thick, finished with a floating coat of neat cement

per standard design :

18.33.1 With common burnt clay F.P.S.(non modular) bricks of class designation 7.5 Each 1.000 10862.40 10862.400

Total of sub-head (EXTERNAL SEWERAGE SYSTEM ) 55,662.35

Repairs to Toilets Works Total : 18,76,080.53 -

Say (In Lakhs): 18.76 -

D. Repair to Plinth Protection & Plaster Works

Dismantling old plaster or skirting raking out joints and cleaning the

61 15.56 surface for plaster including disposal of rubbish to the dumping ground Sqm 0.000 54.65 0.000

within 50 metres lead.

Repairs to plaster of thickness 12 mm to 20 mm in patches of area 2.5

and under, including cutting the patch in proper shape, raking out

62 14.1 preparing and plastering the surface of the walls complete, including

of rubbish to the dumping ground, all complete as per direction of

14.1.2 With cement mortar 1:4 (1cement: 4 coarse sand) Sqm 0.000 560.500 0.000

63 13.4 12 mm cement plaster of mix

Digitally signed by JAYA

Sl DSR Rate (In Amount on DSR -

Item Description Units Total Qty Non DSR

64 13.5 15mm cement plaster on rough side of single or half brick wall of mix

65 13.16 6 mm cement plaster of mix

Removing dry or oil bound distemper, water proofing cement paint

66 13.91 and the like by scrapping, sand papering and preparing the surface Sqm 0.000 25.15 0.000

smooth including necessary repairs to scratches etc. complete.

Providing and applying white cement based putty of average thickness

67 13.80 1 mm, of approved brand and manufacturer, over the plastered wall Sqm 0.000 156.05 0.000

surface to prepare the surface even and smooth complete.

Distempering with oil bound washable distemper of approved brand

and manufacture to give an even shade :

New work (two or more coats) over and including water

thinnable priming coat with cement primer

Distempering with 1st quality acrylic distember (Ready mix) having

69 13.81.1 content less than 50 grams/ litre of approved brand and manufacture Sqm 0.000 62.70 0.000

including applying additional coats wherever required to achieve even

shade and colour Old work (one or more coats)

70 13.46 Finishing walls with Acrylic Smooth exterior paint of required shade :

New work (Two or more coat applied @ 1.67 ltr/10 sqm over and

13.46.1 including priming Sqm 0.000 160.60 0.000

coat of exterior primer applied @ 0.90 kg/10 sqm)

Removing white or colour wash by scrapping and sand papering and

the surface smooth including necessary repairs to scratches etc.

72 13.11 Finishing walls with Acrylic Smooth exterior paint of required shade :

Old work (Two or more coat applied @ 1.67 ltr/ 10 sqm) on existing

73 13.5 15 mm cement plaster on rough side of single or half brick wall of mix:

13.5.2 1:6 (1 cement: 6 coarse sand) (Outer Plaster) Sqm 0.000 395.35 0.000

Making plinth protection 50mm thick of cement concrete 1:3:6 (1

cement : 3 coarse

sand (zone-III) derived from natural sources : 6 graded stone

aggregate 20 mm

nominal size derived from natural sources) over 75mm thick bed of

ballast 40 mm nominal size, well rammed and consolidated and

fine sand, including necessary excavation, levelling & dressing &

Repair to Plinth Protection & Plaster Works Total : - -

Say (In Lakhs): -

E. Repairs to Door/Windows

Dismantling doors, windows and clerestory windows (steel or wood)

75 15.12 including chowkhats, architrave, holdfasts etc. complete and stacking

50 metres lead :

15.12.1 Of area 3 sq. metres and below Nos 12.000 367.20 4406.400

76 14.90 Renewal of old putty of glass panes (length) Mtr 189.400 56.15 10634.810

Providing and fixing bright finished brass single acting spring hinges

necessary brass screws etc. complete :

Digitally signed by JAYA

Sl DSR Rate (In Amount on DSR -

Item Description Units Total Qty Non DSR

Providing and fixing factory made single extruded WPC (Wood Polymer

Composite) solid plain flush door shutter of required size comprising

polymer of K value 58-60 (Suspension Grade), calcium carbonate and

fibers (wood powder/ rice husk/wheat husk) and non toxic additives

toxicity index of 12 for 100 gms) having minimum density of 650

screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum

compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2

resistance to spread of flame of Class A category with property of

termite/borer proof, water/moisture proof and fire retardant and fixing

stainless steel butt hinges of required size with necessary full body

star headed counter sunk S.S screws, all as per direction of Engineer-

Charge. (Note: stainless steel butt hinges and necessary S.S screws

Providing and fixing wire gauge shutters using galvanized M.S. wire

of average width of aperture 1.4 mm in both directions with wire of

mm, for doors, windows and clerestory windows with hinges and

9.27.2 30 mm thick shutters

9.27.2.2 With ISI marked stainless steel butt hinges of required size

9.27.2.2.2 Kiln seasoned and chemically treated hollock wood Sqm 0.000 3447.800 0.000

Providing and fixing ISI marked oxidised M.S. sliding door bolts with

80 9.62 nuts and

screws etc. complete : (Copper oxidized as per IS 1378).

Providing and fixing ISI marked oxidised M.S. tower bolt black finish,

type) with necessary screws etc. complete : (Copper oxidized as per

Providing and fixing aluminium handles, ISI marked, anodised (anodic

82 9.100 not less than grade AC 10 as per IS : 1868) transparent or dyed to

colour or shade, with necessary screws etc. complete :

Providing and fixing aluminium hanging floor door stopper, ISI marked,

83 9.101 (anodic coating not less than grade AC 10 as per IS : 1868)

transparent or dyed

to required colour and shade, with necessary screws etc. complete.

9.101.2 Twin rubber stopper Nos 0.000 72.350 0.000

Providing and fixing wooden moulded beading to door and window

iron screws, plugs and priming coat on unexposed surface etc.

9.40.2 Kiln seasoned and chemically treated hollock wood

Providing and fixing ISI marked oxidised M.S. single acting spring

85 9.59 hinges with

necessary screws etc. complete. (Copper oxidized as per IS 1378).

Providing and fixing pressed steel door frames conforming to IS: 4351,

manufactured from commercial mild steel sheet of 1.60 mm

thickness, including

hinges, jamb, lock jamb, bead and if required angle threshold of mild

of section 50x25 mm, or base ties of 1.60 mm, pressed mild steel

rigidly fixed together by mechanical means, including M.S. pressed

2.5 mm thick with mortar guards, lock strike-plate and shock

specified and applying a coat of approved steel primer after pre-

the surface as directed by Engineer-in-charge:

Digitally signed by JAYA

Sl DSR Rate (In Amount on DSR -

Item Description Units Total Qty Non DSR

Providing and fixing factory made ISI marked steel glazed doors,

ventilators, side /top /centre hung, with beading and all members

F7D,F4B, K11 B and K12 B etc. complete of standard rolled steel

sections, joints

mitred and flash butt welded and sash bars tenoned and riveted,

providing and fixing of hinges, pivots, including priming coat of

primer, but excluding the cost of other fittings, complete all as per

design, (sectional weight of only steel members shall be measured for

Fixing with 15x3 mm lugs 10 cm long embedded in cement concrete

10.11.1 15x10x10 cm of C.C. 1:3:6 (1 Cement : 3 coarse sand : 6 graded Kg 633.600 131.050 83033.280

stone aggregate

20 mm nominal size) @22 Kg/Sqm

Providing and fixing M.S. grills of required pattern in frames of

88 9.48 with M.S. flats, square or round bars etc. including priming coat with

steel primer all complete.

9.48.2 Fixed to openings /wooden frames with rawl plugs screws etc. Kg 576.000 238.350 137289.600

Providing and fixing T-iron frames for doors, windows and ventilators

steel Tee-sections, joints mitred and welded, including fixing of

hinges and screws and applying a priming coat of approved steel

Fixing with 15x3 mm lugs 10 cm long embedded in cement concrete

10.13.1 15x10x10 cm of C.C. 1:3:6 (1 Cement : 3 coarse sand : 6 graded Kg 204.750 141.700 29013.075

stone aggregate

20 mm nominal size).

Providing and fixing oxidised M.S. casement stays (straight peg type)

necessary screws etc. complete. (Copper oxidized as per IS : 1378).

9.68.1 300 mm weighing not less than 330 grams Nos 20.000 67.400 1348.000

9.68.2 250 mm weighing not less than 280 grams Nos 30.000 61.050 1831.500

Providing & fixing glass panes with putty and glazing clips in steel

windows, clerestory windows, all complete with :

10.30.1 4.0 mm thick glass panes (weight not less than 10 kg/ sqm) Sqm 62.360 1390.150 86689.754

92 13.50 Applying priming coat:

With ready mixed aluminum primer of approved brand and

manufacture on resinous wood and plywood

Painting with synthetic enamel paint of approved brand and

93 13.62 manufacture of

required colour to give an even shade :

Two or more coats on new work over an under coat of suitable shade

ordinary paint of approved brand and manufacture

Providing and fixing PVC rigid foam sheet 1 mm thick on existing door

(bathroom and W.C. doors) using synthetic rubber based adhesive.

Repairs to Door/Windows Works Total : 7,62,755.16 -

Say (In Lakhs): 7.63

F. Repairs to Flooring

Demolishing cement concrete manually/ by mechanical means

95 15.2 disposal of material within 50 metres lead as per direction of Engineer -

15.2.2 Nominal concrete 1:4:8 or leaner mix (i/c equivalent design mix) Cum 0.000 1503.60 0.000

Providing and laying in position cement concrete of specified grade

96 4.1 excluding

the cost of centering and shuttering - All work up to plinth level :

1:5:10 (1 cement : 5 coarse sand (zone-III) derived from natural

stone aggregate 40 mm nominal size derived from natural sources

Providing and laying in position cement concrete of specified grade

97 4.1 excluding

the cost of centering and shuttering - All work up to plinth level :

Digitally signed by JAYA

Sl DSR Rate (In Amount on DSR -

Item Description Units Total Qty Non DSR

1:2:4 (1 cement : 2 coarse sand (zone-III) derived from natural

4.1.3 sources : 4 graded Cum 0.000 7878.50 0.000

stone aggregate 20 mm nominal size derived from natural sources)

Kota stone slab flooring over 20 mm (average) thick base laid over and

with grey cement slurry mixed with pigment to match the shade of

98 11.26 the slab,

including rubbing and polishing complete with base of cement mortar

cement : 4 coarse sand) :

Kota stone slabs 20 mm thick in risers of steps, skirting, dado and

on 12 mm (average) thick cement mortar 1:3 (1 cement: 3 coarse

jointed with grey cement slurry mixed with pigment to match the

slabs, including rubbing and polishing complete.

Marble stone flooring with 18 mm thick marble stone, as per sample of

approved by Engineer-in-charge, over 20 mm (average) thick base of

100 11.23 cement

mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with grey

including rubbing and polishing complete with :

11.23.5 Udaipur green marble Sqm 0.000 2428.600 0.000

Cement concrete flooring 1:2:4 (1 cement : 2 coarse sand : 4 graded

101 11.3 aggregate) finished with a floating coat of neat cement, including

but excluding the cost of nosing of steps etc. complete.

11.3.1 40 mm thick with 20 mm nominal size stone aggregate Mtr 0.000 614.200 0.000

Repairs to Flooring Works Total : - -

Say (In Lakhs): -

Grand Total 26,38,835.69 -

Grand Total 26,38,835.69 -

Digitally signed by JAYA

COST ABSTRACT :- REPAIR WORK OF BOYS DORMITORY FOR 320 nos OF STUDENTS - JNV, MAYURBHANJ, ODISHA

Amount on Amount on

Sl DSR Rate (In

Item Description Units Total Qty DSR - 2023 (In Non DSR

A. Structural Repair & Retrofitting

Chipping of unsound/weak concrete material from slabs, beams,

columns etc. with manual Chisel and/ or by standard power driven

percussion type or of approved make including tapering of all edges,

1 26.28 making square shoulders of cavities including cleaning the exposed

concrete surface and reinforcement with wire brushes etc. and

disposal of debris for all lead and lifts all complete as per direction of

Engineer-In-Charge

A. 26.28.2 50mm average thickness Sqm 87.760 256.350 22497.276

B. 26.28.3 25 mm avarage thickness Sqm 105.120 126.750 13323.960

Cleaning of reinforcement from rust from the reinforcing bars to give

it a total rust free steel surface by using alkaline chemical rust

remover of approved make with paint brush and removing loose

2 26.29 particles after 24 hours of its application with wire brush and

washing with water and allowing it to dry, all complete as per direction

of Engineer-In-Charge.

26.29.1 Bars upto 12 mm diameter Mtr 3086.08 8.250 25460.160

Cleaning of exposed concrete surface of sticking material including

loose and foreign material by sand blasting with coarse sand followed

by and including cleaning with oil free air blast as per direction of

Engineer in charge.

Shotcreting R.C.C. columns, beams and slabs etc. in layers with

approved design mix concrete having the specified minimum

characteristic compressive strength [with ordinary portland cement,

4 26.38 coarse sand and graded stone aggregate of 10 mm maximum size

in proportion as per design criteria] including the cost of centering

and shuttering at edges and corners etc. as directed by Engineer in-

Note: Rates shall include the providing necessary ground wires etc.

The levelling gauges, if used, shall be paid for separately. Payment

under this item shall be made only after proper wet curing has been

done and surface has been satisfactorily evaluated by sounding/

tapping with a blunt metal instrument.

25mm thick in Grade M 25 with cement content not

less than 330 kg per cum

50mm thick in Grade M 25 with cement content not

less than 330 kg per cum

Providing and inserting 12mm dia galvanised steel injection nipple in

honey comb area and along crack line including drilling of holes of

required diametre (20mm to 30mm) up to depth from 30mm to 80mm

5 26.39 at required spacing and making the hole & crack dust free by blowing Nos 160.00 4079.290 652686.400

compressed air, sealing the distance between injection nipple with

adhesive chemical of approved make and allow it to cure complete

as per direction of Engineer-In-Charge.

Providing and fixing hard drawn steel wire fabric of size 75 x25 mm

mesh or other suitable size wire mesh to be fixed & firmly anchored

6 26.40 to the concrete surface by means of "L" shaped mild steel shear key Sqm 157.240 902.550 141916.962

welded with existing reinforcement including the cost of materials,

labour, tool & plants as approved by Engineer-in-charge.

Digitally signed by JAYA

Amount on Amount on

Sl DSR Rate (In

Item Description Units Total Qty DSR - 2023 (In Non DSR

Repair to plaster of thickness 12 mm to 20 mm in patches with epoxy

based dampgaurd (Dr. Fixit Make) , including cutting the area of

plaster in proper shape, raking out joints and preparing and plastering

the durface of the walls complete, including disposal of rubbish to the

dumping ground, all complete as per direction of Engineer- in-Charge.

With cement mortar 1:4 (1cement: 4coarse sand)

Providing and applying white cement based putty of average thickness

8 13.80 1 mm, of approved brand and manufacturer, over the plastered wall Sqm 419.956 156.050 65534.134

surface to prepare the surface even and smooth complete.

Structural Repair & Retrofitting Works Total : 15,06,617.68 -

Say (In Lakhs): 15.07 -

B. Repairs to Roof

Demolishing mud phaska in terracing and disposal of material within

50 metres lead.

Painting (one or more coats) on rain water, soil waste and vent pipes

10 13.96 fittings with synthetic enamel paint of approved brand and

manufacture and

required colour on old work :

13.96.2 100 mm diameter pipes Mtr 0.00 88.900 0.000

Providing and laying APP (Atactic Polypropylene Polymer) modified

prefabricated five layer 3 mm thick water proofing membrane, black

reinforced with non-woven polyester matt consisting of a coat of

for bitumen membrane @ 0.40 litre/sqm by the same membrane

11 14.91 manufacture of

density at 25°C, 0.87-0.89 kg/ litre and viscocity 70-160 cps. Over

coat the layer of membrane shall be laid using Butane Torch and

joints etc, and preparing the surface complete. The vital physical and

Extra for covering top of membrane with Geotextile 120 gsmnon

woven 100% polyster of thickness 1 to 1.25MM bnded to membrane

with intermittent touch by heating the membrane by Butane Torch as

per manufacturer recommendation

Repair to Roof Works Total : 6,83,243.47 -

Say (In Lakhs): 6.83 -

C. Repairs to Toilets

Demolishing cement concrete manually/ by mechanical means

12 15.2 including disposal of material within 50 metres lead as per direction of

Engineer - in charge.

15.2.2 Nominal concrete 1:4:8 or leaner mix (i/c equivalent design mix) Cum 4.388 ###### 47617.318

Demolishing R.C.C. work manually/ by mechanical means including

13 15.3 stacking of steel bars and disposal of unserviceable material within 50 Cum 0.672 3551.250 2386.440

metres lead as per direction of Engineer - in- charge.

Demolishing brick work manually/ by mechanical means including

14 15.7 stacking of serviceable material and disposal of unserviceable material

within 50 metres lead as per direction of Engineer-in-charge.

Removing mortar from bricks and cleaning bricks including stacking

within a lead of 50 m (stacks of cleaned bricks shall be measured):

15.8.3 From brick work in cement mortar Nos 3.892 6700.800 26076.833

Dismantling tile work in floors and roofs laid in cement mortar

16 15.23 including

stacking material within 50 metres lead.

15.23.1 For thickness of tiles 10 mm to 25 mm Sqm 1255.23 73.400 92133.809

Providing and laying in position cement concrete of specified grade

17 4.1 excluding the cost of centering and shuttering - All work up to plinth

1:5:10 (1 cement : 5 coarse sand (zone-III) derived from natural

stone aggregate 40 mm nominal size derived from natural sources)

Providing and laying in position cement concrete of specified grade

18 4.1 excluding the cost of centering and shuttering - All work up to plinth

Digitally signed by JAYA

Amount on Amount on

Sl DSR Rate (In

Item Description Units Total Qty DSR - 2023 (In Non DSR

1:2:4 (1 cement : 2 coarse sand (zone-III) derived from natural

4.1.3 sources : 4 graded stone aggregate 20 mm nominal size derived from Cum 2.925 6258.750 18306.844

natural sources)

Reinforced cement concrete work in walls (any thickness), including

attached pilasters, buttresses, plinth and string courses, fillets,

19 5.2 columns, pillars, piers, abutments, posts and struts etc. above plinth

level up to floor five level, excluding cost of centering, shuttering,

finishing and reinforcement :

1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) derived from natural

5.2.2 sources : 3 graded stone aggregate 20 mm nominal size derived from Cum 0.672 708.950 476.414

natural sources)

Centering and shuttering including strutting, propping etc. and removal

of form for all heights:

5.9.16 Edges of slabs and breaks in floors and walls

Centering and shuttering including strutting, propping etc. and removal

of form for all heights:

5.9.3 Suspended floors, roofs, landings, balconies and access platform Sqm 6.720 332.400 2233.728

Steel reinforcement for R.C.C. work including straightening, cutting,

bending, placing in position and binding all complete upto plinth level.

5.22.6 Thermo-Mechanically Treated bars of grade Fe-500D or more. Kg 52.752 107.850 5689.303

Brick work with common burnt clay F.P.S. (non modular) bricks of

23 6.4 class designation 7.5 in superstructure above plinth level up to floor V

level in all shapes and sizes in :

6.4.2 Cement mortar 1:6 (1 cement : 6 coarse sand) Cum 5.962 9105.950 54286.032

Half brick masonry with common burnt clay F.P.S. (non modular)

24 6.13 bricks of class designation 7.5 in superstructure above plinth level up

to floor V level.

6.13.2 Cement mortar 1:4 (1 cement :4 coarse sand) Sqm 20.160 1186.000 23909.760

Extra for providing and placing in position 2 Nos 6mm dia. M.S. bars at

every third course of half brick masonry.

Providing and fixing Ist quality ceramic glazed wall tiles conforming to

(thickness to be specified by the manufacturer), of approved make, in

shades except burgundy, bottle green, black of any size as approved

26 8.31 in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed Sqm 1040.31 1267.950 1319061.065

mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement

3.3kg per sqm, including pointing in white cement mixed with

pigment of matching

shade complete.

Providing and laying Ceramic glazed floor tiles of size 300x300 mm

(thickness to be specified by the manufacturer) of 1st quality

to IS : 15622 of approved make in colours such as White, Ivory, Grey,

27 11.37 Fume Red Brown, laid on 20 mm thick cement mortar 1:4 (1 Cement : sqm 214.919 1096.550 235669.429

4 Coarse sand), Jointing with grey cement slurry @ 3.3 kg/sqm

pointing the joints with white cement and matching pigment etc.,

Dismantling of flushing cistern of all types (C.I./PVC/Vitrious China)

28 15.52 including stacking of useful materials near the site and disposal of Each 10.000 112.05 1120.500

unserviceable materials within 50 metres lead.

White Vitreous china Orissa pattern W.C. pan of size 580x440 mm

type foot rests

Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass

30 17.7 taps, 32 mm C.P. brass waste of standard pattern, including painting

and brackets, cutting and making good the walls wherever require:

White Vitreous China Flat back wash basin size 550x 400 mm with

15 mm C.P. brass pillar tap

Digitally signed by JAYA

Amount on Amount on

Sl DSR Rate (In

Item Description Units Total Qty DSR - 2023 (In Non DSR

Providing and fixing P.V.C. waste pipe for sink or wash basin including

waste fittings complete.

Providing and fixing 600x450 mm beveled edge mirror of superior

32 17.31 approved quality) complete with 6 mm thick hard board ground fixed Each 0.000 1607.95 0.000

cleats with C.P. brass screws and washers complete.

Providing and fixing white vitreous china flat back or wall corner type

front urinal basin of 430x260x350 mm and 340x410x265 mm sizes

17.4.1 One urinal basin with 5 litre white P.V.C. automatic flushing cistern Each 6.000 1648.95 9893.700

Providing and fixing PTMT towel rail complete with brackets fixed to

34 17.73 cleats with CP brass screws with concealed fittings arrangement of

quality and colour.

600 mm long towel rail with total length of 645 mm, width 78 mm and

height of 88 mm, weighing not less than 190 gms.

Water Supply Installations

Dismantling G.I. pipes (external work) including excavation and

35 15.44 trenches after taking out the pipes, manually/ by mechanical means

including stacking of pipes within 50 metres lead as per direction of

Engineer-in-charge :

Dismantling C.I. pipes including excavation and refilling trenches after

taking out the pipes, manually/ by mechanical means breaking lead

36 15.45 joints, melting of lead and making into blocks including stacking of

& lead at site within 50 metre lead as per direction of Engineer-in-

Dismantling of C.I. sluice valve including stacking of useful materials

37 15.53 within

a lead of 50 metres

38 17.35 Providing and fixing soil, waste and vent pipes :

17.35.1.2 100mm Centrifugally cast (spun) iron socket & spigot (S&S) pipe as per IS:

17.35.2.2 75mm Centrifugally cast (spun) iron socketed pipe as per IS: 3989 Mtr 85.000 1186.00 100810.000

Providing lead caulked joints to sand cast iron/centrifugally cast (spun)

39 17.58 iron pipes

and fittings of diameter :

Providing and fixing M.S. holder-bat clamps of approved design to

iron/cast iron (spun) pipe embedded in and including cement concrete

40 17.37 10x10x10 cm of 1:2:4 mix (1 cement : 2 coarse sand : 4 graded

stone aggregate

20 mm nominal size), including cost of cutting holes and making good

Providing and fixing trap of self cleansing design with screwed down or

41 17.60 grating with or without vent arm complete, including cost of cutting

good the walls and floors :

17.60.2.1 100mm inlet & 75mm outlet Sand cast iron S&S as per IS - 3989 Each 5.000 1975.15 9875.750

42 17.57 Providing and fixing collar :

17.57.1.2 100 mm Sand cast iron S&S as per IS - 3989 Each 38.000 513.15 19499.700

17.57.2.2 75 mm Sand cast iron S&S as per IS - 3989 Each 48.000 362.05 17378.400

43 17.39 Providing and fixing plain bend of required degree.

Digitally signed by JAYA

Amount on Amount on

Sl DSR Rate (In

Item Description Units Total Qty DSR - 2023 (In Non DSR

17.39.1.1 100 mm dia Sand cast iron S&S as per IS - 1729 Each 38.000 470.45 17877.100

17.39.2.2 75 mm dia Sand cast iron S&S as per IS - 3989 Each 48.000 390.50 18744.000

Providing and fixing bend of required degree with access door,

44 17.38 insertion rubber

washer 3 mm thick, bolts and nuts complete.

17.38.1.2 100 mm dia Sand cast iron S&S as per IS - 1729 Each 38.000 705.20 26797.600

17.38.2.2 75 mm dia Sand cast iron S&S as per IS - 3989 Each 48.000 522.80 25094.400

Providing and fixing single equal plain junction of required degree with

45 17.43 access

door, insertion rubber washer 3 mm thick, bolts and nuts complete.

17.43.1.1 100x100x100 mm Sand cast iron S&S as per IS - 1729 Each 38.000 726.55 27608.900

17.43.2.1 75x75x75 mm Sand cast iron S&S as per IS - 1729 Each 48.000 629.50 30216.000

46 17.56 Providing and fixing terminal guard :

17.56.1.2 100 mm dia Sand cast iron S&S as per IS - 1729 Each 38.000 506.00 19228.000

17.56.2.2 75 mm dia Sand cast iron S&S as per IS - 3989 Each 48.000 404.75 19428.000

47 17.29 Providing and fixing 100 mm sand cast Iron grating for gully trap. Each 10.000 53.25 532.500

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes,

thermal stability for hot & cold water supply, including all CPVC plain

threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing.

48 18.80 This includes

jointing of pipes & fittings with one step CPVC solvent cement and the

cutting chases and making good the same including testing of joints

as per direction of Engineer in Charge.

Concealed work, including cutting chases and making good the walls

18.8.1 15 mm nominal dia Pipes Mtr 185.000 497.80 92093.000

18.8.2 20 mm nominal dia Pipes Mtr 150.000 537.60 80640.000

18.8.3 25 mm nominal dia Pipes Mtr 105.000 627.25 65861.250

18.8.4 32 mm nominal dia Pipes Mtr 120.000 739.30 88716.000

49 18.21 Providing and fixing uplasticised PVC connection pipe with brass unions :

50 18.21 Providing and fixing uplasticised PVC connection pipe with brass unions :

Providing and fixing C.P. brass bib cock of approved quality

51 18.49 conforming to

Providing and fixing C.P. brass long body bib cock of approved quality

conforming to IS standards and weighing not less than 690 gms.

Providing and fixing C.P. brass angle valve for basin mixer and geyser

53 18.53 points

of approved quality conforming to IS:8931

Providing and fixing ball valve (brass) of approved quality, High or low

pressure, with plastic floats complete :

Providing and fixing gun metal gate valve with C.I. wheel of approved

55 18.17 quality

(screwed end) :

Providing and fixing rectangular high density polyethylene water

loft tank with cover, conforming to ISI : 12701, colour of opaque

56 18.48 A approved by Engineer-in-charge. The rate includes making necessary Ltr 8000.000 11.00 88000.000

for inlet, outlet & over flow pipes. The base support i/c fittings &

tank shall be paid separately

57 18.16 Providing and fixing brass stop cock of approved quality :

Digitally signed by JAYA

Amount on Amount on

Sl DSR Rate (In

Item Description Units Total Qty DSR - 2023 (In Non DSR

Providing and fixing on wall face unplasticised Rigid PVC rain water

conforming to IS : 13592 Type A, including jointing with seal ring

IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single

socketed pipes.

Providing and fixing on wall face unplasticised - PVC moulded fittings/

accessories for unplasticised Rigid PVC rain water pipes conforming to

13592 Type A, including jointing with seal ring conforming to IS :

10 mm gap for thermal expansion.

Providing and fixing C.P. Brass extension nipple (size 15mmx50mm)

approved make and quality as per direction of Engineer-in-charge.

Providing and fixing PTMT extension nipple for water tank pipe,

61 18.75 fittings of

approved quality and colour.

18.75.3 25mm nominal bore, weighing not less than 62 gms Each 2.000 113.35 226.700

Total of sub-head (Water Supply Installations ) 10,86,908.40

EXTERNAL SEWERAGE SYSTEM

Taking out C.I. cover with frame from R.C.C. top slab of manholes of

sizes including demolishing of R.C.C. work manually/ by mechanical

and stacking of useful materials near the site and disposal of

materials within 50 metres lead as per direction of Engineer-in-

Dismantling of road gully chamber of various sizes including C.I.

with frame including stacking of useful materials near the site and

of unserviceable materials within 50 metres lead including refilling the

Dismantling of manhole including R.C.C. top slab, C.I. cover with

64 19.24 including stacking of useful materials near the site and disposal of

unserviceable materials within 50 m lead as per direction of Engineer-

19.24.1 Rectangular manhole 90x80 cm and 45 cm deep Each 2.000 2540.85 5081.700

Raising manhole cover and frame slab to required level including

65 19.26 existing slab and making good the damage as required (Raising depth

manhole to be paid separately) :

Rectangular manhole 90x80 cm with rectangular cover 600 x 450 mm

Making chases up to 7.5x7.5 cm in walls including making good and

with matching surface after housing G.I. pipe etc.

67 18.76 Cutting holes up to 30x30 cm in walls including making good the same:

18.76.1 With common burnt clay F.P.S. (non modular) bricks Each 6.000 416.80 2500.800

Cutting holes up to 15x15 cm in R.C.C. floors and roofs for passing

etc. and repairing the hole after insertion of drain pipe etc. with

68 18.77 cement concrete Each 12.000 452.00 5424.000

1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm

size), including finishing complete so as to make it leak proof.

Digitally signed by JAYA

Amount on Amount on

Sl DSR Rate (In

Item Description Units Total Qty DSR - 2023 (In Non DSR

Constructing masonry Chamber 30x30x50 cm inside, in brick work in

mortar 1:4 (1 cement :4 coarse sand) for stop cock, with C. I. surface

100x100 x75 mm (inside) with hinged cover fixed in cement concrete

mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm

69 18.32 nominal

size), i/c necessary excavation, foundation concrete 1:5:10 ( 1

cement : 5 fine

sand : 10 graded stone aggregate 40mm nominal size ) and inside

with cement mortar 1:3 (1 cement : 3 coarse sand) 12mm thick,

finished with a

floating coat of neat cement complete as per standard design :

18.32.1 With common burnt clay F.P.S.(non modular) bricks of class designation 7.5

Constructing masonry Chamber 60x60x75 cm inside, in brick work in

mortar 1:4 (1 cement : 4 coarse sand) for sluice valve, with C.I.

100mm top diameter, 160 mm bottom diameter and 180 mm deep (

chained lid and RCC top slab 1:2:4 mix (1 cement : 2 coarse sand : 4

70 18.33 stone aggregate 20mm nominal size ) , i/c necessary excavation,

concrete 1:5:10 (1 cement : 5 fine sand : 10 graded stone aggregate

nominal size) and inside plastering with cement mortar 1:3 (1 cement

sand) 12 mm thick, finished with a floating coat of neat cement

per standard design :

18.33.1 With common burnt clay F.P.S.(non modular) bricks of class designation 7.5Each 1.000 10862.40 10862.400

Total of sub-head (EXTERNAL SEWERAGE SYSTEM ) 55,061.65

Repairs to Toilets Works Total : 30,88,079.15 -

Say (In Lakhs): 30.88 -

D. Repair to Plinth Protection & Plaster Works

Dismantling old plaster or skirting raking out joints and cleaning the

71 15.56 surface for plaster including disposal of rubbish to the dumping ground Sqm 0.000 54.650 0.000

within 50 metres lead.

Repairs to plaster of thickness 12 mm to 20 mm in patches of area

2.5 sq.meters and under, including cutting the patch in proper shape,

72 14.10 raking out joints and preparing and plastering the surface of the walls 0.000

complete, including disposal of rubbish to the dumping ground, all

complete as per direction of Engineer-in-Charge.

14.1.2 With cement mortar 1:4 (1 cement: 4 coarse sand) Sqm 0.000 560.500 0.000 -

73 14.9 Renewal of old putty of glass panes Mtr 0.000 56.150 0.000

Removing dry or oil bound distemper, water proofing cement paint

74 13.91 and the like by scrapping, sand papering and preparing the surface Sqm 0.000 25.150 0.000

smooth including necessary repairs to scratches etc. complete.

75 13.40 12 mm cement plaster of mix 0.000

76 13.50 15mm cement plaster on rough side of single or half brick wall of mix 0.000

77 13.16 6 mm cement plaster of mix 0.000

Providing and applying white cement based putty of average thickness

78 13.80 1 mm, of approved brand and manufacturer, over the plastered wall Sqm 0.000 156.050 0.000

surface to prepare the surface even and smooth complete.

Distempering with oil bound washable distemper of approved brand

and manufacture to give an even shade :

New work (two or more coats) over and including water

thinnable priming coat with cement primer

Digitally signed by JAYA

Amount on Amount on

Sl DSR Rate (In

Item Description Units Total Qty DSR - 2023 (In Non DSR

Distempering with 1st quality acrylic distember (Ready mix) having

80 13.81.1 content less than 50 grams/ litre of approved brand and manufacture Sqm 0.000 62.700 0.000

including applying additional coats wherever required to achieve even

shade and colour Old work (one or more coats)

81 13.46 Finishing walls with Acrylic Smooth exterior paint of required shade : 0.000

New work (Two or more coat applied @ 1.67 ltr/10 sqm over and

13.46.1 including priming Sqm 0.000 160.600 0.000

coat of exterior primer applied @ 0.90 kg/10 sqm)

Removing white or colour wash by scrapping and sand papering and

the surface smooth including necessary repairs to scratches etc.

83 13.11 Finishing walls with Acrylic Smooth exterior paint of required shade : 0.000

Old work (Two or more coat applied @ 1.67 ltr/ 10 sqm) on existing

84 13.5 15 mm cement plaster on rough side of single or half brick wall of mix: 0.000

13.5.2 1:6 (1 cement: 6 coarse sand) (Outer Plaster) Sqm 0.000 395.350 0.000

Making plinth protection 50mm thick of cement concrete 1:3:6 (1

cement : 3 coarse

sand (zone-III) derived from natural sources : 6 graded stone

aggregate 20 mm

nominal size derived from natural sources) over 75mm thick bed of

ballast 40 mm nominal size, well rammed and consolidated and

fine sand, including necessary excavation, levelling & dressing &

Repair to Plinth Protection & Plaster Works Total : - -

Say (In Lakhs): 2.50

E. Repairs to Door/Windows

Dismantling doors, windows and clerestory windows (steel or wood)

86 15.12 including chowkhats, architrave, holdfasts etc. complete and stacking

50 metres lead :

15.12.1 Of area 3 sq. metres and below Nos 14.000 367.200 5140.800

Providing and fixing ISI marked oxidised M.S. single acting spring

87 9.59 hinges with

necessary screws etc. complete. (Copper oxidized as per IS 1378).

Providing and fixing factory made single extruded WPC (Wood Polymer

Composite) solid plain flush door shutter of required size comprising

polymer of K value 58-60 (Suspension Grade), calcium carbonate and

fibers (wood powder/ rice husk/wheat husk) and non toxic additives

toxicity index of 12 for 100 gms) having minimum density of 650

screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum

compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2

resistance to spread of flame of Class A category with property of

termite/borer proof, water/moisture proof and fire retardant and

stainless steel butt hinges of required size with necessary full body

star headed counter sunk S.S screws, all as per direction of Engineer-

Charge. (Note: stainless steel butt hinges and necessary S.S screws

paid separately)

Providing and fixing wire gauge shutters using galvanized M.S. wire

of average width of aperture 1.4 mm in both directions with wire of

mm, for doors, windows and clerestory windows with hinges and

Digitally signed by JAYA

Amount on Amount on

Sl DSR Rate (In

Item Description Units Total Qty DSR - 2023 (In Non DSR

9.27.2 30 mm thick shutters

9.27.2.2 With ISI marked stainless steel butt hinges of required size

9.27.2.2.2 Kiln seasoned and chemically treated hollock wood Sqm 0.000 3447.800 0.000

Providing and fixing ISI marked oxidised M.S. sliding door bolts with

90 9.62 nuts and

screws etc. complete : (Copper oxidized as per IS 1378).

Providing and fixing ISI marked oxidised M.S. tower bolt black finish,

type) with necessary screws etc. complete : (Copper oxidized as per

Providing and fixing aluminium handles, ISI marked, anodised (anodic

92 9.100 not less than grade AC 10 as per IS : 1868) transparent or dyed to

colour or shade, with necessary screws etc. complete :

Providing and fixing aluminium hanging floor door stopper, ISI

marked, anodised

93 9.101 (anodic coating not less than grade AC 10 as per IS : 1868)

transparent or dyed

to required colour and shade, with necessary screws etc. complete.

9.101.2 Twin rubber stopper Nos 0.000 72.350 0.000

Providing and fixing wooden moulded beading to door and window

iron screws, plugs and priming coat on unexposed surface etc.

9.40.2 Kiln seasoned and chemically treated hollock wood

Providing and fixing oxidised M.S. single acting spring hinges with

necessary screws etc. complete. (Copper oxidized as per IS 1378).

Providing and fixing pressed steel door frames conforming to IS: 4351,

manufactured from commercial mild steel sheet of 1.60 mm

thickness, including

hinges, jamb, lock jamb, bead and if required angle threshold of mild

of section 50x25 mm, or base ties of 1.60 mm, pressed mild steel

rigidly fixed together by mechanical means, including M.S. pressed

2.5 mm thick with mortar guards, lock strike-plate and shock

specified and applying a coat of approved steel primer after pre-

the surface as directed by Engineer-in-charge:

Providing and fixing factory made ISI marked steel glazed doors,

ventilators, side /top /centre hung, with beading and all members

F7D,F4B, K11 B and K12 B etc. complete of standard rolled steel

sections, joints

mitred and flash butt welded and sash bars tenoned and riveted,

providing and fixing of hinges, pivots, including priming coat of

primer, but excluding the cost of other fittings, complete all as per

design, (sectional weight of only steel members shall be measured for

Fixing with 15x3 mm lugs 10 cm long embedded in cement concrete

10.11.1 15x10x10 cm of C.C. 1:3:6 (1 Cement : 3 coarse sand : 6 graded Kg 0.000 131.050 0.000

stone aggregate

20 mm nominal size) @22 Kg/Sqm

Providing and fixing M.S. grills of required pattern in frames of

98 9.48 with M.S. flats, square or round bars etc. including priming coat with

steel primer all complete.

Digitally signed by JAYA

Amount on Amount on

Sl DSR Rate (In

Item Description Units Total Qty DSR - 2023 (In Non DSR

9.48.2 Fixed to openings /wooden frames with rawl plugs screws etc. Kg 0.000 238.350 0.000

Providing and fixing T-iron frames for doors, windows and ventilators

steel Tee-sections, joints mitred and welded, including fixing of

hinges and screws and applying a priming coat of approved steel

Fixing with 15x3 mm lugs 10 cm long embedded in cement concrete

10.13.1 15x10x10 cm of C.C. 1:3:6 (1 Cement : 3 coarse sand : 6 graded Kg 73.500 141.700 10414.950

stone aggregate

20 mm nominal size).

Providing and fixing oxidised M.S. casement stays (straight peg type)

necessary screws etc. complete. (Copper oxidized as per IS : 1378).

9.68.1 300 mm weighing not less than 330 grams Nos 0.000 67.400 0.000

9.68.2 250 mm weighing not less than 280 grams Nos 0.000 61.050 0.000

Providing & fixing glass panes with putty and glazing clips in steel

windows, clerestory windows, all complete with :

10.30.1 4.0 mm thick glass panes (weight not less than 10 kg/ sqm) Sqm 0.000 1390.150 0.000

102 13.50 Applying priming coat:

With ready mixed aluminum primer of approved brand and

manufacture on resinous wood and plywood

Painting with synthetic enamel paint of approved brand and

103 13.62 manufacture of

required colour to give an even shade :

Two or more coats on new work over an under coat of suitable shade

ordinary paint of approved brand and manufacture

Providing and fixing PVC rigid foam sheet 1 mm thick on existing door

(bathroom and W.C. doors) using synthetic rubber based adhesive.

Repairs to Door/Windows Works Total : 1,37,260.52 -

Say (In Lakhs): 1.37

F. Repairs to Flooring

Demolishing cement concrete manually/ by mechanical means

105 15.2 disposal of material within 50 metres lead as per direction of Engineer -

15.2.2 Nominal concrete 1:4:8 or leaner mix (i/c equivalent design mix) Cum 0.000 1503.60 0.000

Providing and laying in position cement concrete of specified grade

106 4.1 excluding

the cost of centering and shuttering - All work up to plinth level :

1:5:10 (1 cement : 5 coarse sand (zone-III) derived from natural

stone aggregate 40 mm nominal size derived from natural sources

Providing and laying in position cement concrete of specified grade

107 4.1 excluding

the cost of centering and shuttering - All work up to plinth level :

1:2:4 (1 cement : 2 coarse sand (zone-III) derived from natural

4.1.3 sources : 4 graded Cum 0.000 7878.50 0.000

stone aggregate 20 mm nominal size derived from natural sources)

Kota stone slab flooring over 20 mm (average) thick base laid over and

with grey cement slurry mixed with pigment to match the shade of

108 11.26 the slab,

including rubbing and polishing complete with base of cement mortar

cement : 4 coarse sand) :

Kota stone slabs 20 mm thick in risers of steps, skirting, dado and

on 12 mm (average) thick cement mortar 1:3 (1 cement: 3 coarse

jointed with grey cement slurry mixed with pigment to match the

slabs, including rubbing and polishing complete.

Digitally signed by JAYA

Amount on Amount on

Sl DSR Rate (In

Item Description Units Total Qty DSR - 2023 (In Non DSR

Marble stone flooring with 18 mm thick marble stone, as per sample of

approved by Engineer-in-charge, over 20 mm (average) thick base of

110 11.23 cement

mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with grey

including rubbing and polishing complete with :

11.23.5 Udaipur green marble Sqm 0.000 2428.600 0.000

Repairs to Flooring Works Total : - -

Say (In Lakhs): -

Grand Total 54,15,200.81 -

Grand Total 54,15,200.81 -

Digitally signed by JAYA

COST ABSTRACT :- REPAIR WORK OF GIRLS DORMITORY FOR 240 nos OF STUDENTS - JNV, MAYURBHANJ, ODISHA

Sl DSR Rate (In Amount on DSR - on Non

Item Description Units Total Qty

No 2023 Rs) 2023 (In Rs) DSR (In

A. Structural Repair & Retrofitting

Chipping of unsound/weak concrete material from slabs, beams,

columns etc. with manual Chisel and/ or by standard power driven

percussion type or of approved make including tapering of all edges,

1 26.28 making square shoulders of cavities including cleaning the exposed

concrete surface and reinforcement with wire brushes etc. and

disposal of debris for all lead and lifts all complete as per direction of

Engineer-In-Charge

A. 26.28.2 50mm average thickness Sqm 65.820 256.350 16872.957

B. 26.28.3 25 mm avarage thickness Sqm 78.840 126.750 9992.970

Cleaning of reinforcement from rust from the reinforcing bars to give

it a total rust free steel surface by using alkaline chemical rust

remover of approved make with paint brush and removing loose

particles after 24 hours of its application with wire brush and

washing with water and allowing it to dry, all complete as per

of Engineer-In-Charge.

26.29.1 Bars upto 12 mm diameter Mtr 2314.56 8.250 19095.120

Cleaning of exposed concrete surface of sticking material including

loose and foreign material by sand blasting with coarse sand followed

by and including cleaning with oil free air blast as per direction of

Engineer in charge.

Shotcreting R.C.C. columns, beams and slabs etc. in layers with

approved design mix concrete having the specified minimum

characteristic compressive strength [with ordinary portland cement,

4 26.38 coarse sand and graded stone aggregate of 10 mm maximum size

in proportion as per design criteria] including the cost of centering

and shuttering at edges and corners etc. as directed by Engineer in-

Note: Rates shall include the providing necessary ground wires etc.

The levelling gauges, if used, shall be paid for separately. Payment

under this item shall be made only after proper wet curing has been

done and surface has been satisfactorily evaluated by sounding/

tapping with a blunt metal instrument.

25mm thick in Grade M 25 with cement content not

less than 330 kg per cum

50mm thick in Grade M 25 with cement content not

less than 330 kg per cum

Providing and inserting 12mm dia galvanised steel injection nipple in

honey comb area and along crack line including drilling of holes of

required diametre (20mm to 30mm) up to depth from 30mm to

at required spacing and making the hole & crack dust free by blowing

compressed air, sealing the distance between injection nipple with

adhesive chemical of approved make and allow it to cure complete

as per direction of Engineer-In-Charge.

Providing and fixing hard drawn steel wire fabric of size 75 x25 mm

mesh or other suitable size wire mesh to be fixed & firmly anchored

6 26.40 to the concrete surface by means of "L" shaped mild steel shear key Sqm 117.930 902.550 106437.722

welded with existing reinforcement including the cost of materials,

labour, tool & plants as approved by Engineer-in-charge.

Digitally signed by JAYA

Sl DSR Rate (In Amount on DSR - on Non

Item Description Units Total Qty

No 2023 Rs) 2023 (In Rs) DSR (In

Repair to plaster of thickness 12 mm to 20 mm in patches with epoxy

based dampgaurd (Dr. Fixit Make) , including cutting the area of

plaster in proper shape, raking out joints and preparing and plastering

the durface of the walls complete, including disposal of rubbish to the

dumping ground, all complete as per direction of Engineer- in-Charge.

With cement mortar 1:4 (1cement: 4coarse sand)

Providing and applying white cement based putty of average thickness

8 13.80 1 mm, of approved brand and manufacturer, over the plastered wall Sqm 314.967 156.050 49150.600

surface to prepare the surface even and smooth complete.

Structural Repair & Retrofitting Works Total : 11,09,259.19 -

Say (In Lakhs): 11.09 -

B. Repairs to Roof

Demolishing mud phaska in terracing and disposal of material within

50 metres lead.

Painting (one or more coats) on rain water, soil waste and vent pipes

10 13.96 fittings with synthetic enamel paint of approved brand and

manufacture and

required colour on old work :

13.96.2 100 mm diameter pipes Mtr 0.00 88.900 0.000

Providing and laying APP (Atactic Polypropylene Polymer) modified

prefabricated five layer 3 mm thick water proofing membrane, black

reinforced with non-woven polyester matt consisting of a coat of

for bitumen membrane @ 0.40 litre/sqm by the same membrane

density at 25°C, 0.87-0.89 kg/ litre and viscocity 70-160 cps. Over

coat the layer of membrane shall be laid using Butane Torch and

joints etc, and preparing the surface complete. The vital physical and

parameters of the membrane shall be as under : Joint strength in

and transverse direction at 23°C as 650/ 450N/ 5cm. Tear strength

in longitudinal

and transverse direction as 300/250N. Softening point of membrane

than 150°C. Cold flexibility shall be upto -2°C when tested in

accordance with

ASTM, D - 5147. The laying of membrane shall be got done through

Extra for covering top of membrane with Geotextile 120 gsmnon

woven 100% polyster of thickness 1 to 1.25MM bnded to membrane

with intermittent touch by heating the membrane by Butane Torch as

per manufacturer recommendation

Repair to Roof Works Total : 5,12,432.47 -

Say (In Lakhs): 5.12 -

C. Repairs to Toilets

Demolishing cement concrete manually/ by mechanical means

12 15.2 including disposal of material within 50 metres lead as per direction of

Engineer - in charge.

15.2.2 Nominal concrete 1:4:8 or leaner mix (i/c equivalent design mix) Cum 4.388 10852.950 47617.318

Demolishing R.C.C. work manually/ by mechanical means including

13 15.3 stacking of steel bars and disposal of unserviceable material within 50 Cum 0.672 3551.250 2386.440

metres lead as per direction of Engineer - in- charge.

Demolishing brick work manually/ by mechanical means including

14 15.7 stacking of serviceable material and disposal of unserviceable

material within 50 metres lead as per direction of Engineer-in-charge.

Removing mortar from bricks and cleaning bricks including stacking

within a lead of 50 m (stacks of cleaned bricks shall be measured):

15.8.3 From brick work in cement mortar Nos 3.892 6700.800 26076.833

Disposal of building rubbish / malba / similar unserviceable,

dismantled or waste materials by mechanical means, including

16 15.60 loading, transporting, unloading to approved municipal dumping Cum 31.381 263.950 8282.942

ground or as approved by Engineer-in-charge, beyond 50 m initial

lead, for all leads including all lifts involved.

Dismantling tile work in floors and roofs laid in cement mortar

17 15.23 including

stacking material within 50 metres lead.

15.23.1 For thickness of tiles 10 mm to 25 mm Sqm 627.61 73.400 46066.904

Digitally signed by JAYA

Sl DSR Rate (In Amount on DSR - on Non

Item Description Units Total Qty

No 2023 Rs) 2023 (In Rs) DSR (In

Providing and laying in position cement concrete of specified grade

18 4.1 excluding the cost of centering and shuttering - All work up to plinth

1:5:10 (1 cement : 5 coarse sand (zone-III) derived from natural

4.1.10 sources : 10 graded stone aggregate 40 mm nominal size derived Cum 4.388 1607.950 7054.881

from natural sources)

Providing and laying in position cement concrete of specified grade

19 4.1 excluding the cost of centering and shuttering - All work up to plinth

1:2:4 (1 cement : 2 coarse sand (zone-III) derived from natural

4.1.3 sources : 4 graded stone aggregate 20 mm nominal size derived from Cum 2.925 6258.750 18306.844

natural sources)

Reinforced cement concrete work in walls (any thickness), including

attached pilasters, buttresses, plinth and string courses, fillets,

20 5.2 columns, pillars, piers, abutments, posts and struts etc. above plinth

level up to floor five level, excluding cost of centering, shuttering,

finishing and reinforcement :

1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) derived from natural

5.2.2 sources : 3 graded stone aggregate 20 mm nominal size derived from Cum 0.672 708.950 476.414

natural sources)

Centering and shuttering including strutting, propping etc. and

removal of form for all heights:

5.9.16 Edges of slabs and breaks in floors and walls

Centering and shuttering including strutting, propping etc. and

22 5.9 removal of form

for all heights:

5.9.3 Suspended floors, roofs, landings, balconies and access platform Sqm 6.720 332.400 2233.728

Steel reinforcement for R.C.C. work including straightening, cutting,

bending, placing in position and binding all complete upto plinth level.

5.22.6 Thermo-Mechanically Treated bars of grade Fe-500D or more. Kg 52.595 107.850 5672.371

Brick work with common burnt clay F.P.S. (non modular) bricks of

24 6.4 class designation 7.5 in superstructure above plinth level up to floor V

level in all shapes and sizes in :

6.4.2 Cement mortar 1:6 (1 cement : 6 coarse sand) Cum 5.962 9105.950 54286.032

Half brick masonry with common burnt clay F.P.S. (non modular)

25 6.13 bricks of class designation 7.5 in superstructure above plinth level up

to floor V level.