Construction of Rest House for RITES Officers at Plot No. V -37/13 in DLF City, Phase-III, Gurgaon

Amount

Total Amount of BoQ 2

Amount after unconditional Rebate

Description of Work / Item(s)

Amount

Total of BoQ 3, BoQ 4 and BoQ 5

Total Amount of BoQ3 (Item Rate)

Total Amount of BoQ4 (Percentage Rate)

Total Amount of BoQ5 (Percentage Rate)

Description of Work / Item(s)

Amount

Schedule - (B) Bill of Quantites for Non Schedule Items (MR ITEMS) (CIVIL)

Providing and supplying heavy duty HITRE500V3 or equivalant with Rebar with a predefined ratio (3:1) of resin and hardener in a soft foil pack of 330ml, 500ml. The product should be approved by ETA, ICC, CSTB, COLA, BZS with Shock approval, Seismic approval in Anchors and Rebars to use in cracked/un-cracked concrete, tested for service temperature of -40deg C to +80 deg C. Application to be designed separately for Rebares as Simply Supported Moment or Splice as per EC2/TR23 or relevant tested and accepted rebar guidelines. LEED certified injection adhesive for rebar fixing in wet/dry flooded holes conditions for diameters. The chemical should have service life of more than 50 years and is to be tested for water tightness.

Drilling hole with double flute type drill bits/hollow drill bits to the required depth by rotary hammer drill, cleaning with brush and jet of clean air, filling resin and hardener using serrated nozzle to eliminate mixing error with standard HDE A22 battery dispenser along with piston plug and extension hose for longer depths to ensure no air bubbles are in the hole and then fixing the re-bar, conducting occasional site inspection, executing work by trained personnel and occasional supervision from the manufacturer’s representative in India. The installation and the setting instructions should be strictly followed as per the manufacturer’s recommendations. RE 500 V3 for rebar application must have approval for Seismic, Fatigue and Fire.

M.R. 1.1 - (16mm dia rebar at 320mm depth)

M.R. 1.2 - ( a) (12mm dia rebar at 240mm depth)

M.R. 1.2 - ( b) (8mm dia rebar at 160mm depth)

M.R. 1.3 - Providing, Fabricating, fixing on walls or required surface with IDC Archi Concrete - an anti-algae acrylic-siloxane plaster coating for exteriors and interiors, fine grain (0.5 - 0.7 mm). Concrete Finish of Make Asian paints. Brand name of Product Archi-concrete. Includes complete work with fixing material, tools & plants, scaffolding etc as per company specifications complete as per engineer in charge

M.R. 1.4 - Providing, Fabricating, fixing on walls or required surface with Stone-jaisalmer mint PC size - 50mm x 50mm , cut shape triangular tapered, Thickness range : Taopering from 32mm on one side and 16mm on another. The panels of minimum size 300mm X 300mm composing such pieces should have nylon Netting base fixed with Epoxy adhesive. Netted tile to be fixed on plastered wall using Letecrete 290 as per company specifications. Includes complete work with fixing material, tools & plants, scaffolding etc as per company specifications complete as per engineer in charge

M.R. 1.5 - Supply and installation of Vertical plantation system HDPE living wall trays. Colour: - Black (PPCP POT), Dimensions: -(4x4 inch). Supply and installation at wall by fasteners, anchors or welded.Drip Irrigation System: Supply and installation of Irrigation system in each wall trays. Lateral Poly Pipe 12mm or 16 mm, Poly and Cap Connectors, Poly tee(3 Way) Connectors. Poly Elbow Connectors ,Pressure 4Kg/pressure, Drippers. Water pressure for irrigation. Drainage – 2” drain pipe for drainage at panels bottom. Soil Media/ Supply and installation of indoor and indoor plants, soil media (Mixed Bio Wall Soil Media, vermin, micronutrients, anti-fungal treatment) Indoor Plants- Pepromia green, Pepromia variegated, Syngonium varieties, Oxycardium philodendron, Pothos, Ferns, Chlorophytum, Arelia, Crotons

M.R. 1.6 - Providing and fixing Marble stone flooring with 18 mm thick marble stone, as per sample of marble approved by Engineer-in-charge, over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid with grey cement slurry, jointed with light pigmented white cement in matching color, including rubbing and polishing complete with : (Jaisalmer yellow marble)

M.R. 1.7 - Providing and applying Asian Paints WOODTECH PU EXTERIOR with all base coats etc complete on wooden surface as per company specifications with coverage of 8-9sq.m./ltr/coat .The paint application process of 7 steps to be followed as per company specifications including exterior grade Sealer, sanding, stainers, top coats etc complete. Cost includes all coats to give finish as per engineer in charge

M.R. 1.8 - Providing and applying Asian Paints WOODTECH EMPORIO PU PALETTE with all base coats etc complete on wooden surface as per company specifications with coverage of 8-9sq.m./ltr/coat .The paint application process of 7 steps to be followed as per company specifications including exterior grade Sealer, sanding, stainers, top coats etc complete. Cost includes all coats to give finish as per engineer in charge.

M.R. 1.9 - Providing and laying 16mm thick homogenous vitrified floor tiles in 600 x 600 size with water absorption less than 0.5% conforming to IS: 1054-2, Breaking strength more than 7500 N (ISO 10545-4), laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc., complete. Make PAVIT

Metal Works

M.R. 2.1 - Fabrication and installation of Aluminium Façade works : Polyster Powder coated Aluminium sections (Hindalco 8385 - 76.2 x 44.45 x 2.9 @ 1.799kg/m with End capping. Fixed using SS304 brackets and Hilti fastners on Structural elements. Material of Aluminium sections of Hindalco/Jindal already taken separately in DSR item

M.R. 2.2 Supply and installation of Metal false ceilings, GI lay in Plain Post Coat 1200*300*0.5mm With 15mm Suprafine 32WH & 19mm *19mm Wall Angle Grid System, Metal Plate Ceiling, Includes scaffolding, installation complete as per company specifications and as per engineer in charge ( Make Armstrong or equivalent)

M.R. 2.3 Supply and installation of Aluminum Baffle Wooden Shade of size 100mm*25mm*3600mm with c/c Spacing of 125mm With Accessories in false ceiling works including scaffolding, fixing and finishing as per company specifications ( Make Armstrong or equivalent)

Glass Work

M.R. 3.1 Extra for colored profile in UPVC Sliding doors

M.R. 3.2 Supply and Fixing, fabricating etc of GLASS RAILING Ø 50 mm AISI 316 Grade S.S Handrail (Wall thickness 1.5 mm )10 X 50 mm AISI 316 Grade S.S. Top mounted Flat Baluster with glass holding Accessories with Ø100 x 100 x 8mm Thick 316 Grade base Plate and 2 No. Anchors and Fasteners10 X 50 mm AISI 316 Grade S.S. Top mounted Flat Baluster with Double glass holding Accessories with Ø100 x 100 x 8mm Thick 316 Grade base Plate and 2 No. Anchors and Fasteners10 mm thick Straight Toughened Glass (Up to 650mm height). Includes supply and installation Kich - DT52-3-1G10. All works to be done as per company spefications and as per complete ( Make KICH)

M.R. 3.3 Supply and fixing, fabricating of GLASS Railing Ø 50 mm AISI 316 Grade S.S Handrail (Wall thickness 1.5 mm ) AISI 316 Grade S.S. Ø 50 Side Spacer to hold glass with glass holding Accessories (including Top Bracket to hold Handrail) 12 mm thick Toughened Glass( up to 3 feet of total height from floor to top )[Total Height of Glass 1200mm].All works to be done as per company specification and as per complete satisfacting of engineer in charge Kich - DS2-1W-G15 Make KICH

M.R. 3.4 Supply and fixing, fabricating of Glass railing. Grey powder coated channel profile concealed in floor with fixing as per company detail. 12mm Laminated heat strengthened glass Railing. No handrail. Excluding glass.Imperio railing systems - L-40 Make Imperio Railing Systems. All works to be done as per company specification and as per complete satisfacting of engineer in charge

M.R. 3.5 - Providing and cutting fixing 12mm toughened glass partitions as per drawings fixed with Ozone OCFH-100S Std BM (Hydraulic Bottom Patch for Glass Doors), OPF-2 PLUS-S Std BM top patch fittings and OGH-11-25mmx450mm 'D' type handles. Includes all cutting of holes etc required for fixing of fittings etc. Complete installation finished as per Engineer in charge.

M.R. 3.5.1 Supply of 12mm Toughened Glass

M.R. 3.5.2 supply of Ozone OCFH-135

M.R. 3.5.3 supply of OPF-1-PLUS, OPF-2-PLUS top patch fittings

M.R. 3.5.4 supply of OGHL-55-2P-A-25x2200 handle with lock

M.R. 3.5.5 Installation of the glass partitions including fixing of all items from 3.5.1 to 3.5.4 complete as per company specifications and satisfaction of engineer in charge

M.R. 3.6. Providing and cutting fixing 8mm tempered glass partitions with Ozone Edge series fittings.Saint gobain/ Asahi glass Includes all cutting of holes etc required for fixing of fittings etc. Complete installation finished as per Engineer in charge

M.R. 3.6.1 supply of 8mm Tempered Glass as per DSR

M.R. 3.6.2 supply of OSSH-44-ED - Glass to Glass Hinge 90˚

M.R. 3.6.3 supply of OGC-444-ED - Wall to Glass Connector 90

M.R. 3.6.4 supply of OGC-111-ED - Wall / Floor to Glass Connector

M.R. 3.6.5 Installation of the glass partitions including fixing of all items from 3.6.1 to 3.6.5 complete as per company specifications and satisfaction of engineer in charge

M.R. 3.7 Providing and fixing mirror of superior glass (of approved quality) of 6mm and of required shape and size of approved make with 12mm spacers to keep distance from back wall and including all fasteners, spacers, cutting, holes etc as per complete satisfaction of engineer in charge.

M.R. 3.8 Providing, supplying, lifting and fixing Multiwall Polycarbonate sheet 8 mm of any color as per design including fixing on truss on upper floor with self tapping screws with washer etc complete. The sheet should be installed so that the area is sealed with detailing as per engineer in charge to ensure no water seepage and air leakage from the structure. The sheet shall be sealed with silicone sealant as per requirement and the joints shall be covered with aluminum beading as necessary. Make LEXAN or equivalent

Miscellaneous Items

M.R. 4.1 Providing and Fixing of Overhead Watertank of SS. Supply and fixing of 10000 Ltr capacity overhead water tank. Material Of Construction : SS 316 L. Insulation: (Glass-wool 50mm + SS 304 0.5mm thick sheet). Outer dimension (2mx3mx2m) having Hot dipped galvanized base frame. Installation complete with placing at required place with mechanical/manual means, cutting of holes if required for connections etc, complete fitting.

M.R. 4.2 Providing and fixing AC 4 Class wooden laminated flooring as per company standards. Wear resistant interlocking planks size 190 x 1200 with surface layer consisting of a Aluminum Oxide coated tissue to make the flooring surface resistant to impact, scratches, burns & stains. Melamine impregnated decorative wooden texture paper layer on top of wax coated water resistant 8mm HDF base and balancing paper base. 2.5" PVC skirting and reducer complete as per directions of Engineer in charge( Make Pergo-Domestic Extra- Authentic Oak, Plank L-0701-1462 or equivalent).

M.R. 4.2.1 Supply of AC4 Laminated wooden flooring

M.R. 4.2.2 Supply of PVC skirting 2.5"

M.R. 4.2.3 Supply of Reducer

M.R. 4.2.4 Installation of the above wooden flooring items complete as per company specifications

M.R. 4.3 Providing and fixing Greenlam Sturdo Vibrance Rage Toilet Cubicle (of following standard dimension which includes 600mm door size width) made of heat, bacteria, water, chemical, scratch and impact resistant 12mm thick solid compact laminate panels tested as per IS codes. Finish of the compact laminatepanels tested as per IS codes. Finish of the compact laminate should be Raw silk, which includes doors, pilasters & intermediate panels finished with approved texture/shade as per detail drawings & as per IS 2046 and fire retardant BS-476/97 standard. The product should have Green Guard certificate. This also includes providing and fixing in position necessary hardware made out of aluminium & having Gun Metal finish, as per manufacturer's specifications & Architects instrcutions like (1) Door Knob, (2) Gravity hinges, (3) Thumb turn lockset with occupancy indicator, (4) Coat hook (5) U-channel (6) Adjustable foot/pedastal, (7) Aluminum Powder coated Top rail, (8) Rubber noise deafening tape, (9) Screws & wall plugs.The top fitting should consist of Aluminium Powder Coated top rail which will get fixed with Mid & End pilasters. All screws will be of 304 SS grade with satin finish. All pilasters are supported by stainless steel bottom cladding. The base of the stainless steel bottom cladding will be anchored to the floor with a clearance height upto 150 mm."

M.R. 4.3 Toilet Cubicle I-shape (front partition) with standard dimension of 1995mm height x 1000mm width which includes 600mm door size width.

M.R. 4.4 Supply, fabrication, assembling and installation of following Main Sliding gate components. - 4 Module Ms Rack with Studs, Sliding Gate 4 module MS Rack Size- 12 * 30 * 1005 mm - Nylon Side Guide for Sliding Gate, Nylon Guide for Sliding Gate with center shaft and bolts/washer - MS Wheel for Sliding Gate, M.S .Wheel for sliding Gate for 25mm Rail Length, Complete with double ball bearing and mounting bracket - KIT - K-1400 - Sliding Gate Operator Includes : K1400 Operator (RIB, Italy) with K-2007 CRX Fit Flim Photo Sensor : 1 Pair Sun 2 Channel Remote : 1 Nos. Block Key Switch : 1 Nos. Arial without Cable : 1 Nos. Spark Blinker: 1 Nos Base plate with nut bolt (included) Warning Plate & Instruction manual : 1 Nos. - Installation and service charges for all above items including installation of metal gate provided complete on site as per specifications and engineer in charge Make TOSHI AUTOMATIC SYSTEMS or Similar

M.R. 4.5 Supply & installation of Acoustic Wall panels of Woodworks Wall Panel 2400*192*15mm With Clip G 5 & Extruded Keel System (Sqft). Installation on walls as per design, including all fitting fasteners, tools and plants complete as per engineer in charge. Make : Armstrong

M.R. 4. 6 Supply and installation of Acoustic Moving Partition Movable Wall 45dB, RW Sound rating (Laboratory tested) - Fitted with necessary Hardware and acoustic material packed together with Medium Density Fibreboard (MDF). Standard Panel and Expanding Panel thickness - 85mm with 16mm Thick MDF on both sides with side Stacking. Final Finishing has to be done by the Client at his cost. Total No. of panels including the Expanding Panel and door panel; each approx 1000mm Wide. Make Ozone or similar.Includes loading, unloading, installation complete on site

M.R. 4.7 - Access System for rooms. Make DORMA

M.R. 4.7.1 Supply and installation of DEHL RFM 712, SC ANSI H7 IL Electronic Hotel Lock with RF Mifare Technology, 712 design, Satin Chrome Finish, ANSI Lock case, Inside Left Opening Door, H7 Handle design. Keyed Different. The complete system is to be installed as per specifiecation laid out by the company. Includes all fixing and connecting materials etc, complete as per engineer in charge

M.R. 4.7.2 Supply of DENC RFM 7104 D - Encoder ( i/c DHMS V.10 Electronic Hotel Lock Programming Software) with USB port for Programming the RF Cards.

M.R. 4.7.4 Supply of DRFM CARD M1 - RF Mifare M1 cards.

M.R. 4.7.5 Supply of DESS RFM 843C - White - Energy Saving Switch for RF Mifare Cards.

EQUIPMENTS AND FIXTURES

M.R. 5.1 Providing and fixing white vitreous china extended wall mounting water closet HIndware Cat no: 92553 - Splendor Vortex Wall Mounted Closet, including seat cover, nuts, bolts and gasket etc complete. Concealed cistern with fitting shall be paid extra as per separate item given below.

M.R. 5.2 Providing and fixing white vitreous china extended wall mounting water closet HIndware Cat no: 92534 - Essence Rimless S-220 One Piece Closet, including seat cover, and cistern fittings, nuts, bolts and gasket etc complete.

M.R. 5.3 Providing and fixing Hindware Concealo - Body Concealed Cistern with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete.

M.R. 5.4 Providing and fixing wash basin with C.I. brackets, concealed basin mixer of approved quality and make, including painting of fittings and brackets, cutting and making good the walls wherever required. Half pedestal Wash Basin Hindware 91078 - Twilight Pedestal Basin. Concealed Body For Wall Mounted Basin Mixer. Hindware F850093CP. Avior Exposed Part Kit Of Single Lever Wall Mounted Basin Mixer -Hindware F520013CP. 200 Mm Spout F850093

M.R. 5.5 Providing and fixing wash basin with C.I. brackets, concealed basin mixer of approved quality and make, including painting of fittings and brackets, cutting and making good the walls wherever required. Over counter Wash Basin Hindware 91094 - Amazon Over Counter Basin. Concealed Body For Wall Mounted Basin Mixer. Hindware F850093CP. Avior Exposed Part Kit Of Single Lever Wall Mounted Basin Mixer -Hindware F520013CP. 200 Mm Spout F850093

M.R. 5.6 Providing and fixing wash basin with C.I. brackets, concealed basin mixer of approved quality and make, including painting of fittings and brackets, cutting and making good the walls wherever required. Over counter Wash Basin Hindware 91012 - Enigma Semi Recessed Basin. Concealed Body For Wall Mounted Basin Mixer. Hindware F850093CP. Avior Exposed Part Kit Of Single Lever Wall Mounted Basin Mixer -Hindware F520013CP. 200 Mm Spout F850093

M.R. 5.7 Providing and fixing wash basin with C.I. brackets, concealed basin mixer of approved quality and make, including painting of fittings and brackets, cutting and making good the walls wherever required. Over counter Wash Basin Hindware 91207 - Avior R Over Counter Basin. Concealed Body For Wall Mounted Basin Mixer. Hindware F850093CP. Avior Exposed Part Kit Of Single Lever Wall Mounted Basin Mixer -Hindware F520013CP. 200 Mm Spout F850093

M.R. 5.8 - Providing and fixing wash basin with C.I. brackets, concealed basin mixer of approved quality and make, including painting of fittings and brackets, cutting and making good the walls wherever required. Over counter Wash Basin Hindware 10080 - Garnet Under Counter Basin C.P. Brass Centre Hole Basin Mixer With Cast Spout ( Kigston/Marc/Prima/ Parko/Hindware)

M.R. 5.9 - Providing and fixing Hindware F160079CP - Ultra Thin SS Rain Shower 250mm Square. Hindware F160079CP - Ultra Thin SS Rain Shower 250mm Square Shower Arm Heavy Casted. Cat. No.: F110031 Body without wall Flange

M.R. 5.10 - Providing and fixing Hindware F160039CP - Overhead Shower With Shower Arm and Wall Flange

M.R. 5.11 - Providing and fixing concealed shower mixer with connections to spout, shower, hot and cold inlet points using CPVC joints. Concealed Body For shower Mixer. Hindware F850090ACP - Body-SL Concealed Divertor B&S SYS (W/O Knob). Hindware F110046CP - Immacula Single Lever Exposed Parts Kit Of Divertor- ABS

M.R. 5.12 - Providing and fixing Urinal : one piece construction with built-in sensor with fittings, standard size G.I. / PVC flush pipe for back and front flush with standard spreader pipes with fittings, G.I clamps and C.P. brass coupling complete, including painting of fittings and cutting and making good the walls and floors etc. wherever required : Urinal with in-built sensor - Hindware Cat no: 96005 - Alexa Sensor Urinal

M.R. 5.13 - Providing and fixing of Urinal : one piece construction with built-in sensor with fittings, standard size G.I. / PVC flush pipe for back and front flush with standard spreader pipes with fittings, G.I clamps and C.P. brass coupling complete, including painting of fittings and cutting and making good the walls and floors etc. wherever required : Urinal with in-built sensor - Hindware Cat no: 60021 - Flow Sensor Urinal

M.R. 5.14 - Providing and fixing Urinal partition - Hindware Omega SU11OSC. Curved shaped urinal partition with 10mm frosted glass. Size 900 mm x 450 mm, as per company specifications, complete with screws, fittings etc.

M.R. 5.15 - Providing and fixing F160067CP - Health Faucet Abs With 1.2M Flexible PVC Tube And Wall Hook to Eureopean type W.C., complete with screws, fittings

M.R. 5.16 - Providing and fixing F160038CP - Health Faucet Abs With 1.2M Flexible PVC Tube And Wall Hook to Eureopean type W.C., complete with screws, fittings

M.R. 5.17 - Providing and fixing Towel rod with stand - Hindware F840010CP - Immacula Towel Shelf with concealed fittings as per company specifications, complete with screws, fittings

M.R. 5.18 - Providing and fixing Towel rod - Hindware F840013CP - Immacula Towel Bar (60cm) with concealed fittings as per company specifications, complete with screws, fittings

M.R. 5.19 - Providing and fixing Towel ring - Hindware F840002CP - Immacula Towel Ring with concealed fittings as per company specifications, complete with screws, fittings

M.R. 5.20 - Providing and fixing soap dish - HindwareF840006CP - Immacula Soap Dish (Brass) with concealed fittings as per company specifications, complete with screws, fittings

M.R. 5.21 - Providing and fixing paper holder - Hindware F840009CP - Immacula Paper Holder With Cover with concealed fittings as per company specifications, complete with screws, fittings

M.R. 5.22 - Providing and fixing robe hook - Hindware F880004CP - Contessa Robe Hook with concealed fittings as per company specifications, complete with screws, fittings

M.R.. 5.23 - Providing and fixing Glass shelf - Hindware F870011CP - Rubbic Glass Shelf with concealed fittings as per company specifications, complete with screws, fittings

FURNISHING

M.R. 6.1 - Supply, fabrication and installation of High quality Polyester 100mm Vertical Blinds Head Rail: Head rail is of 25mm high and 47 mm wide Extruded High strength aluminum alloy section with Average wall thickness of minimum 0.9mm. The section is anodized for smooth operations and has the provision of Fabric valance matching with louvers fabric. End Control Unit (Reduction Gear Box): End control unit state of art reduction gear box having the reduction ratio of 3.5:1 for a very smooth operation of the blind. This unit Consists of a planetary gear in the outer housing, four small transmission gears fitted in the middle assembly and an end receiving gear attached to central sprocket unit. Tilt Rod: It is made of extruded aluminum having three keyways. The tilt rod is fixed in the end control unit and drives the carrier gear mechanism to rotate the louvers.The average diameter is 5.8mm to achieve minimum torsion deflection Tilter Chain: This is made of 4.5 mm plastic beads molded on 1.5 mm thick polyester cord. The Pitch of the beads is 6mm. The chain drives the procket fixed in the end control unit to rotate the louvers by 180 degrees. The pitch of the chain corresponds to the sprocket in perfect match for trouble free Operation. It is provided in white color. Carrier (Runner): This is a molded component having anti friction additive. It consists of polymer Housing with wheels mounted on sides and has a gear and worm mechanism with vertical worm fixed With a tongued poly carbonate stem to hold the louvers. The worm and gear mechanism are driven by Tilt rod fixed to end control unit to rotate louvers by 180 degrees. The mounted wheels on sides of Casing move on rails of head rail section for resistance free stacking of louvers Spacer: This is made of molded High Polymer ABS, having anti friction additive. It maintains proper Spacing of the runners and ensures overlapping of louvers for perfect light control. It is available in 100 mm size. Installation Bracket: This is made of galvanized steel “L” bracket of thickness 3mm which is fitted with Pressure clip made of spring steel to hold the head-rail. Cord Weight: This is made of ABS material hollow casing with a steel weight inside. Cord: It is 2.2mm in diameter, Nylon braided high strength cord having maximum abrasion resistance & Minimum elongation. Bottom Mechanism (Weight and Chain): The purpose of this is to keep the louver straight & prevent them from swaying. • The bottom weight is made of FILLED PP and is having provision for fixing bottom chain. Available in 100 mm. • Bottom weight is fixed with U- type of clips attached at equal distance on Polyester cord having 0.8mm dia with molded plastic beads on it. Make Vista Polyester series or equivalent 100mm Vertical Blinds

M.R. 6.2 - Supply, fabrication and installation of PVC Venetian Blinds in white colour. Head Rail: Head rail is 53 mm high and 63 mm wide. It is made of aluminum alloy and is provided with matching shade of slats. Valance is already fitted in the head rail of height 50 mm. Head rail is covered by two end caps made up of PVC. Tilter Lock: It is made up of aluminum & is fitted inside the head rail Cord lock: It is fitted inside the head rail & made up of steel. Tilting Cord: It is 2mm in diameter, braided high strength polyester fiber cord for maximum abrasion. resistance and minimum elongation. It is provided with matching shade of slats. With wooden tassels- 2 nos. Lift Cord: It is 2mm in diameter, braided high strength polyester fibre cord for maximum abrasion resistance and minimum elongation. It is provided with matching shade of slats. It comes with wooden tassel- 1 no. and equaliser-1 no. Slats: Bass Wood Slats ; Width= 50mm (+/-0.5mm); Thickness= 3mm (+/- 0.5mm) Ladder tape: Made of polyester tape. Dimensions=25mm x 44mm x 54mm. Bottom Rail: Made of Bass Wood ; Width= 50mm (+/- 0.5mm). Installation Bracket: It is made up of Steel with spring loaded brackets Ladder Button: It is made up of ABS Tilting Rod: It is made of steel of size 6 mm Square rod. The tilt rod is fixed in the tilter mechanism and drives the drum to rotate the Slats. Drum & Cradle: They are molded ABS components with high strength. The Drum and Cradle Assembly Provides Bearing Support to the Tilt Rod and is meant for winding the cord for lifting and rotating the ladder cord for tilting. Including with necessary screws, fastners, clips, clamps etc as required, complete on site. Make Vista Faustina PVC Slats Series or equivalent 50 mm Venetian Blinds

M.R. 6.3 - Supply, fabrication and installation of PVC Venetian Blinds in wooden finish. Head Rail: Head rail is 53 mm high and 63 mm wide. It is made of aluminum alloy and is provided with matching shade of slats. Valance is already fitted in the head rail of height 50 mm. Head rail is covered by two end caps made up of PVC. Tilter Lock: It is made up of aluminum & is fitted inside the head rail Cord lock: It is fitted inside the head rail & made up of steel. Tilting Cord: It is 2mm in diameter, braided high strength polyester fiber cord for maximum abrasion resistance and minimum elongation. It is provided with matching shade of slats. With wooden tassels- 2 nos.Lift Cord: It is 2mm in diameter, braided high strength polyester fibre cord for maximum abrasion resistance and minimum elongation. It is provided with matching shade of slats. It comes with wooden tassel- 1 no. and equaliser-1 no.Slats: Bass Wood Slats ; Width= 50mm (+/-0.5mm); Thickness= 3mm (+/- 0.5mm) Ladder tape: Made of polyester tape. Dimensions=25mm x 44mm x 54mm. Bottom Rail: Made of Bass Wood ; Width= 50mm (+/- 0.5mm). Installation Bracket: It is made up of Steel with spring loaded brackets Ladder Button: It is made up of ABS Tilting Rod: It is made of steel of size 6 mm Square rod. The tilt rod is fixed in the tilter mechanism and drives the drum to rotate the Slats. Drum & Cradle: They are molded ABS components with high strength. The Drum and Cradle Assembly. Provides Bearing Support to the Tilt Rod and is meant for winding the cord for lifting and rotating theladder cord for tilting. Including with necessary screws, fastners, clips, clamps etc as required, complete on site. Make Vista Ailanto Series or equivalent Wooden Venetian Blinds 50mm

M.R. 6.4 - Supply, fabrication, stitching and installation of curtains of Type 1 (luxury finish)with back lining and stiching as per Architect's instructions.. It is made of aluminum alloy and is provided with matching shade of slats. SS 202 hooks fitted in the head rail of height 50 mm. Head rail is covered by two end caps made up of PVC of make D'décor or equivalent

M.R. 6.5 - Supply, fabrication, stitching and installation of curtains of Type 1 (Premium finish)with back lining and stiching as per Architect's instructions.. It is made of aluminum alloy and is provided with matching shade of slats. SS 202 hooks fitted in the head rail of height 50 mm. Head rail is covered by two end caps made up of PVC. Make D'décor or equivalent.

Schedule - ( D ) Bill of Quantites for Sanitary items Non DSR (M.R.)Items

M.R. 7.1 - Providing and Fixing 300mm long SS grab bars fixed to wall with rawl plugs and CP brass screws complete. Make Jaguar AHS-CHR-1501

M.R. 7.2 - Providing and Fixing automatic 'NO-Touch ' electric hand-driers complete with all accessories & fittings.Make -Jaquar (HDR-WHT-M04A) or equivalent

SUB HEAD-WATER SUPPLY INTERNAL

M.R. 8.1 - Supplying, installing, testing & commissioning of electric driven automatic pressurisation pump set consisting of the following : Horizontally mounted centrifugal end suction type Terrace pump complete for delivery of 250 ltrs/minute against a total head of 35 metres approx complete with arrangement for testing of the working of the pumping set as required. Rate shall also include Mechanical Seal.

SUB HEAD-HEAT PUMP (HEAT PUMP -CAHP-3HP)

M.R. 9.1 - Supplying of skid mounted Air Source Packaged Heat pump suitable for water heating and having following salient features of following, complete with piping valave etc.

Rated Heating Capacity of heat Pump - 8 KW Nominal COP - 3.8 Refrigerant Type- R-134a(green Refrigrant) or any other refrigerant approved as per Montreal & Kyoto Protocols. Integrated blue diamond glass lined tank of 445 ltrs Power supply - 220 Volt / 1 phase/ 50 Hz OR 380 Volt/3 phase/50 Hz Microprocessor based control panel with automatic controls and display module. LCD Display Hot Water return pump - 1 Nos., Capacity :- 75 LPM , Head - 20m Valves as required for cleaning of condenser and draining of water.

M.R. 9.2 - EES-120

445 ltr Commercial water tank with 6kw heating inbulit elements. Heating water capacity upto 65°C. Two elements of 3kw each. Blue Diamond Glass Lined Tank. Glass Coated Heating Element with Temperature Control Knob. With Insulation Foam of 50mm.

SUB HEAD-PUMPS AND WATER TREATMENT

M.R. 10.1 - Supplying, Installation, Testing & Commissioning of Vertical inline Pumping set suitable for operation on 415 volts ± 10%, 3 phase and 50 HZ AC supply. The pump shall be made of C.I casing, SS-304 impeller (hard finished and dynamically balanced), stainless steel (304) shaft and sleeve with mechanical seal capable of delivering suitable capacity. Both pump and motor mounted on common M.S. structural base plate bolted to cement concrete foundations complete with Pressure gauge, vibration eliminating pads required and with control panel, control cable and level sensor etc. complete as per specification.

Filter Feed Pumps : (a) Capacity of Pump - 100 LPM (b)No. of pumps - 2 Nos. (1 w + 1 s) (c) Head - 35 to 40Mtr (d) As per manufacturer's recommendation. (e) Degree of Protection - IP "54" ( f ) Class of Insulation - "F" ( g )Location of Pump - In Pump ROOM

M.R. 10.2 - Booster pumps from UGT to OHT : (a) Capacity of Pump - 100 LPM (b) No. of pumps - 2 Nos. (1 w + 1 s) (c) Head - 30Mtr (d) As per manufacturer's recommendation. (e) Degree of Protection - IP "54" ( f ) Class of Insulation - "F" ( g ) Location of Pump - In Pump ROOM

M.R. 10.3 - Supply, installation, testing and commissioning of a set of hydropneumatic vertical inline water transfer pump set, skid mounted with PLC panel factory fitted, for domestic water with single Floating VFD suitable for automatic operation and delivering the specified discharge at the specified head. Each Pump shall be of stainless steel (SS-316) casing along with NRV & ball/butterfly valves at suction & delivery line, impeller (hard finished and dynamically balanced) and shaft and sleeve with mechanical seal capable of delivering suitable capacity and connected by a flexible coupling to a totally enclosed fan cooled (TEFC) induction motor as per IEC standard. The set shall be complete with gunmetal isolation valve on the suction line with 150mm dia pressure gauge, gunmetal non - return valve and gunmetal isolation valve on delivery line, complete with s/s suction and delivery header piping of suitable size. The motor shall be suitable for 415 ± 10% volts, 3 phase, 50 Hz A.C. power supply. The set shall include an automatic control panel and FRP presssure tank of capacity 200 lts. with common base frame and complete connecting accessories. The set shall be completely equipped with floating variable fequency drive for automatic operation as per load requirements and will run alternately in sequence in cascade mode based on water demand. The pump set includes pressure switch along with dry running preventor, electrical Panel and necessary cable from panel to pump and sensor to panel etc. complete.

(a) Capacity of Pump - 100 LPM (b) No. of pumps - 2 Nos. (1 w + 1 s) (c ) Head of Pump - 20 Mtr (d ) As per manufacturer's recommendation. (e ) Degree of Protection - IP "67" (f ) Class of Insulation - "F" (g) Piping and valves - Must be Factory Fitted (h) Location of Pump - At terrace level

M.R. 10.4 - Providing and fixing vertical Pressure Sand Filter (comprising of minimum 500mm media in four graded layer and minimum Height on Straight 1500mm) fabricated from high performance FRP,Tested to 5.0 Kg/m2 , internally treated with coal-tar epoxy, air scouring, collection system initial charge of media, face piping with necessary flanges, gaskets, isolating valves, accessories, nuts & bolts, external painting with 2 coats of red oxide primer and enamel paint etc. with suitable foundation boits & other accessories, mounting frame, complete as required & as specified as per directions of the engineer-in-charge. with the following: Discharge : 6.0 m3/Hour Filtration Rate : 14500 lit./m2/h Suggested dia app. : 1 m

Schedule - ( F ) Bill of Quantites for Fire Fighting items Non-DSR ( M.R.) ITEMS

M.R. 11.1 - Providing and fixing door with frame for all internal fire hydrants fabricated from 20x20x3 mm and 40x20x3 mm aluminium hollow box sections mounted with 3 no. of 100 mm Aluminium butt hinge on Aluminium angle frame of 45x45x5 mm size with hold fasts fixed to wall with P.C.C. (1:2:4) blocks 100x100x100 mm including 2 nos allen key lock for locking along with padlock arrangement & fully glazed with 4 mm thick float glass approved by local Fire Authority, powder coated fire red finish with " fire hose' written on front suitable to house 15 mm long two length of canvas hose with couplings, one no of branch pipe, one fire mans axe and two numbers of portable extinguishers, first aid fire hose and supports for hoses, branch pipes, Axe and hose reel. Size 1200x 600 mm complete as per approved design including necessary fixing arrangement for hoses & axe and branch pipe.)

M.R. 11.2 - Supplying and fixing of Fire Man's Axe with heavy insulated rubber tested upto 20 KV and confirming to IS :926.

M.R. 11.3 - Providing and fixing Carbon-di-oxide fire extinguishers consisting of welded M.S cylindrical body, squeeze lever discharge valve fitted with internal discharge tube, 30cms long high pressure discharge hose, discharge nozzle, suspension bracket, confirming to IS : 15683 finished externally with red enamel paint and fixed to wall with brackets with rawl plug/dash fasteners complete with internal charge. Capacity 4.5 kg. ISI Marked.( Contractor should submit test certificate form manufacturer along with serial number of every extinguishers supplied.)

M.R. 11.4 - Providing and fixing water Co2(ISI marked) extinguishers including all accessories as per IS specification with wall bracket with rawl plug 9 Ltr.

M.R. 11.5 - Providing and fixing of self illuminated / auto glow "EXIT" signs printed on photoluminescent sheet containing self illuminated base chemical, of appropriate size not less than 400 x 150 mm, suspended from ceiling or fixed to the walls with accessories as required and as directed at site.

M.R. 11.6 - Providing and fixing gunmetal single acting air release valve with screwed inlet 25 mm dia..

M.R. 11.7 - Providing and fixing blank flanges as per table 'E' with asbestos gasket, nut, bolts, washers complete. 150 mm dia.

Schedule - ( H ) Bill of Quantites for Kitchen Equipment Non-DSR ( M.R.) ITEMS

M.R. 12.1 - Supply of Work Table With Bottom Shelf & 01 Drawer Make : Jindal Stainless of size 750mm X800mm X850mm +150mm

M.R. 12.2 - Supply of Masala Stand with 10 no. 1/9 GN. Pans with lids Make : Jindal Stainless of size 560mm X365mm X125mm

M.R. 12.3- Supply of 04 Burner Gas Range with bottom pipe shelf, Gridd size-300mmx300mm. Make : Jindal Stainless of size 900mm x800mm x850mm +150mm with Gas fuel

M.R. 12.4 - Supply of Work Table With Sink & Bottom pipe shelf, Sink size 400mm x400mm x300mm. Make : Jindal Stainless of size 600mm X800mm X850mm +150mm

M.R. 12.5 - Supply of S.S. Tandoor on Wheels Make : Jindal Stainless of size 800mm X800mm X850mm +150mm with Gas fuel

M.R. 12.6 - Supply of S.S. Exhaust Hood with s.s. Baffle filters Make : Jindal Stainless of size 3850mm x900mm x500mm with Elect fuel

M.R. 12.7- Supply of Mini Combi Oven, With s.s. Stand, Imported Convotherm Model OES 6.10 & 3 Tray Required Make : Jindal Stainless of size 515mm x790mm x720mm +850mm with Elect fuel

M.R. 12.8 - Supply of S.S. Exhaust Hood with s.s. Baffle filters Make : Jindal Stainless of size 650mm x900mm x400mm with Elect fuel

M.R. 12.9 - Supply of Mobile Work Table With Bottom Shelf Make : Jindal Stainless of size 1200mm X500mm X850mm

M.R. 12.10 - Supply of 02 Door Vertical Chiller Temp. + 2 Deg. To + 4 Deg Make : Jindal Stainless of size 720mm x800mm x2120mm with ELECT. fuel

M.R. 12.11 - Supply of Storage rack with 05 shelf Make : Jindal Stainless of size 900mm x450mm x1850mm

M.R. 12.12 - Supply of Menumaster Commercial Microwave oven Make : Jindal Stainless of size 508mm x420mm x320mm with ELECT. fuel

M.R. 12.13- Supply of Work Table With Bottom Shelf Make : Jindal Stainless of size 1000mm X500mm X850mm +150mm

M.R. 12.14 - Supply of 4 Slote toaster Make : Jindal Stainless of size 335mm x240mm x200mm with ELECT. fuel

M.R. 12.15 - Supply of Soiled dish table with garbage chute & bottom cross bracing with 02 sink , sink size -400mm x400mm x300mm. Make : Jindal Stainless of size 1500mm x600mm x850mm +150mm

M.R. 12.16 - Supply of Waste bin trolley Make : Jindal Stainless of size Dia. 350mm x750mm

M.R. 12.17 - Supply of Wall mounted pipe shelf Make : Jindal Stainless of size 1500mm x350mm x150mm

M.R. 12.18 - Supply of Clean & pot wash rack with 05 shelf Make : Jindal Stainless of size 900mm x450mm x1850mm

M.R. 12.19 - Supply of Work Table With Sink & Bottom cross bracing , Sink size 400x400x300mm. Make : Jindal Stainless of size 1200mm X550mm X850mm +150mm with ELECT. fuel

M.R. 12.20 - Supply of Juicer Mixer Grinder, Moter 900 Watts, Make : Jindal Stainless of size 375mm x410mm x485mm Approx.

M.R. 12.21 - Supply of Waste bin trolley Make : Jindal Stainless of size Dia. 350mm x750mm with ELECT. fuel

M.R. 12.22 - Supply of Air Curtain Make : Jindal Stainless of size 1050mm. Length

M.R. 12.23 - Supply of Wall mounted mixer faucet, Jaguar FLR-CHR-5163 or similar

M.R. 12.24 - Supply of Deck mounted mixer faucet.

M.R. 12.25 - Installation & Commissioning Charges of all the items mentioned above

BILL OF QUANTITIES for Non Schedule Items (MR ITEMS) (ELECTRICAL)

MR E- 1 Supply, installation, testing and commissioning of cubical type LT switchgear suitable for 415V, 3 Phase, 4 Wire 50 Hz AC supply system fabricated in compartmentalized design from CRCA sheet steel of 2 mm thick for frame work and covers, 3mm thick for gland plates including cleaning & finishing complete with 7 tank process for powder coating in approved shade, having suitable capacity extensible type TPN Aluminium Alloy bus bars of high conductivity, bottom base channel of MS section not less than 100mm x 50mm x 5mm thick, fabrication shall be done in transportable sections, entire panel shall have a common copper earth bar of size 25mm x 5mm at the rear with 2 Nos. earth stud, solid connections from main bus bar to switch gears with required size of Al. bus bars and control wiring with 2.5sq.mm. FRLS insulated copper conductor cable, cable alleys, cable gland plates in two half, i/c providing following 415V Switchgear and accessories in the Panel as per SLD ,specifications complete as required (General arrangement and schematic Drawings to be approved by the Deptt. before start of fabrication) . The Bus bars will be as per the IEC 6068-3-247 Standard. IP Protection-42

1 No 160 A Microprocessor Based FP MCCB, 36 KA service breaking capacity with heavy duty solid neutral link alongwith Earth fault relay and CBCT.Rotary handle and spreader link

1 No 160 A, 36 KA Auto changeover switch,

Metering for incoming:

Digital Multifunction meter (MFM-4) with RS-485 communication port for measurement of PF, V, A & Hz , equivalent to EM6459, with CT as required.

Phase indicating lamps RYB with 2 Amps SP MCB back up.

BUSBAR

Electrolytic high conductivity Aluminium three phase and neutral busbars rated at 200 amps, 36KA, insulated with heat shrinkable coloured PVC sleeves & clip on shrouds for joints. Neutral Bus Bar shall be 50% of Phase Bus Bar.

OUTGOINGS

10 nos. 63 Amps 10KA FP MCB

ON / OFF indicating lamps with MCB as backup protection.

4 nos. 63 Amps thermal magnetic release 25 kA 440 volt FP MCCB with overcurrent,earth fault and short circuit releases each complete with:

ON / OFF indicating lamps with MCB as backup protection.

Main Panel as described as above and as per specification complete in all respects.

Main Panel as described as above and as per specification complete in all respects.

PLUMBING PANEL (TERRACE FLOOR)

MR E-2 : Supply, installation, testing and commissioning of cubical type LT switchgear suitable for 415V, 3 Phase, 4 Wire 50 Hz AC supply system fabricated in compartmentalized design from CRCA sheet steel of 2 mm thick for frame work and covers, 3mm thick for gland plates including cleaning & finishing complete with 7 tank process for powder coating in approved shade, having suitable capacity extensible type TPN Aluminium Alloy bus bars of high conductivity, bottom base channel of MS section not less than 100mm x 50mm x 5mm thick, fabrication shall be done in transportable sections, entire panel shall have a common copper earth bar of size 25mm x 5mm at the rear with 2 Nos. earth stud, solid connections from main bus bar to switch gears with required size of Al. bus bars and control wiring with 2.5sq.mm. FRLS insulated copper conductor cable, cable alleys, cable gland plates in two half, i/c providing following 415V Switchgear and accessories in the Panel as per SLD ,specifications complete as required (General arrangement and schematic Drawings to be approved by the Deptt. before start of fabrication) . The Bus bars will be as per the IEC 6068-3-247 Standard. IP Protection-42

The incoming shall comprise the following :-

1 No 63 A thermal magnetic release FP MCCB, 25 KA service breaking capacity with heavy duty solid neutral link alongwith Earth fault relay and CBCT.

Metering for incoming: Digital Multifunction meter (MFM-4) with RS-485 communication port for measurement of PF, V, A & Hz , equivalent to EM6459, with CT as required. Phase indicating lamps RYB with 2 Amps SP MCB back up.

Bus Bars: V100 Amps TPN Aluminium Bus Bars of suitable length Bus bars shall be colour coded and insulated by heat shrinkable sleaves & clip on shrouds for joints.

Outgoing : 4 Nos. 25A(10KA) TPN MCB . 2 Nos. 25A(10KA) TPN MCB . 2 HP -2 Nos.(Water pump) Dol Starter 2 HP - 1 Nos.(Presure pump on terrace) Dol Starter

Plumbing Panel described as above and all as per specification.

CONTROL PANELS (Fire Fighting )

MR E-3 : Supply, installation, testing and commissioning of cubical type LT switchgear suitable for 415V, 3 Phase, 4 Wire 50 Hz AC supply system fabricated in compartmentalized design from CRCA sheet steel of 2 mm thick for frame work and covers, 3mm thick for gland plates including cleaning & finishing complete with 7 tank process for powder coating in approved shade, having suitable capacity extensible type TPN Aluminium Alloy bus bars of high conductivity, bottom base channel of MS section not less than 100mm x 50mm x 5mm thick, fabrication shall be done in transportable sections, entire panel shall have a common copper earth bar of size 25mm x 5mm at the rear with 2 Nos. earth stud, solid connections from main bus bar to switch gears with required size of Al. bus bars and control wiring with 2.5sq.mm. FRLS insulated copper conductor cable, cable alleys, cable gland plates in two half, i/c providing following 415V Switchgear and accessories in the Panel as per SLD ,specifications complete as required (General arrangement and schematic Drawings to be approved by the Deptt. before start of fabrication) . The Bus bars will be as per the IEC 6068-3-247 Standard.IP Protection 42

Incoming : The incoming shall comprise the following :-

1 No 63 A thermal magnetic release FP MCCB, 25 KA service breaking capacity with heavy duty solid neutral link alongwith Earth fault relay and CBCT.

Metering for incoming: Digital Multifunction meter (MFM-4) with RS-485 communication port for measurement of PF, V, A & Hz , equivalent to EM6459, with CT as required. Phase indicating lamps RYB with 2 Amps SP MCB back up.

Bus Bars: 80 Amps TPN Aluminium Bus Bars of suitable length Bus bars shall be colour coded and insulated by heat shrinkable sleaves & clip on shrouds for joints.

Outgoing: 2 Nos. 40A(10KA) TPN MCB . 12.5 HP -1 Nos.(Jocky pump) Star Delta Starter

Fire Panel described as above and all as per specification.

SUB HEAD- LIGHT & FIXTURE

MR E-4 : Supply installation,testing and commissioning of 1x 200 mm Exhaust fan , Plastic body with louver, etc complete as required. MAKE-Crompton -Brisk Air 200 mm or Equivalent make as per list of approved makes

MR E-5 : Supply, installation, testing & commissioning of DALI Dimmable 4ft Linear slim profile Suspended Fixture 20W (±10%) UGR<19 Compatible & the luminaire shall be with system efficacy ≥ 95lm/W. Housing: Powder Coated Aluminium Alloy Housing. IP20 , Optics: HET Diffuser. The operating CCT shall be 4000K with CRI of ≥80. The luminaire shall be with BIS Registered electronic driver with input voltage range of 150 to 270V , THD ≤ 10% & PF ≥ 0.9, 50,000 Hrs LED Life with L70 Criteria.The LED Driver shall be easily avaiable in India for repair and service. The LED shall be SMD type. Luminaire shall have minimum surge protection of 2KV.The luminaire shall be with following certifications: LM79 & LM80 issued by LED manufacture along with Photo Biological Safety Standard. Wipro Cat No.:LM43-421XXX-40UGWC ( DALI ) + LMX 431 ( Suspended). or equivalent to approved make list

MR E-6 : Supply, installation, testing & commissioning of DALI Dimmable 4ft Linear slim profile Suspended Fixture 20W (±10%) UGR<19 Compatible & the luminaire shall be with system efficacy ≥ 95lm/W. Housing: Powder Coated Aluminium Alloy Housing. IP20 , Optics: Colimetric Lens. The operating CCT shall be 4000K with CRI of ≥80. The luminaire shall be with BIS Registered electronic driver with input voltage range of 150 to 270V , THD ≤ 10% & PF ≥ 0.9, 50,000 Hrs LED Life with L70 Criteria.The LED Driver shall be easily avaiable in India for repair and service. The LED shall be SMD type. Luminaire shall have minimum surge protection of 2KV.The luminaire shall be with following certifications: LM79 & LM80 issued by LED manufacture along with Photo Biological Safety Standard. Wipro Cat No.:LM43-271-045-40-WX ( DALI ) + LMX 431 ( Suspended) or equivalent to approved make list

MR E-7 : Supply, installation, testing & commissioning of Surface Mount Round Led Downlighter consuming a system wattage of 18W (±10%) & the luminaire shall be with system efficacy ≥ 100 lm / W. Housing: CRCA Powder Coated. IP20 , Optics: PMMA/Polysterene Diffuser. The operating CCT shall be 4000K with CRI of ≥80. The luminaire shall be with BIS Registered electronic driver with input voltage range of 150 to 270V , THD ≤ 10% & PF ≥ 0.9, 50,000 Hrs LED Life with L70 Criteria. The LED Driver shall be easily avaiable in India for repair and service. The LED shall be SMD type. Luminaire shall have minimum surge protection of 2KV.The luminaire shall be with following certifications: LM79 & LM80 issued by LED manufacture along with Photo Biological Safety Standard. Wipro Cat No.: LD99-281-XXX40SMWH or equivalent to approved make list

MR E- 8 : Supply, installation, testing & commissioning of Pendant Mounted Round Led Downlighter consuming a system wattage of 18W (±10%) & the luminaire shall be with system efficacy ≥ 95 lm / W. Housing: Extruded Aluminium Powder Coated. IP20 , Optics: PMMA/Polysterene Diffuser. The operating CCT shall be 4000K with CRI of ≥80. The luminaire shall be with BIS Registered electronic driver with input voltage range of 150 to 270V , THD ≤ 10% & PF ≥ 0.9, 50,000 Hrs LED Life with L70 Criteria. The LED Driver shall be easily avaiable in India for repair and service. The LED shall be SMD type. Luminaire shall have minimum surge protection of 2KV.The luminaire shall be with following certifications: LM79 & LM80 issued by LED manufacture along with Photo Biological Safety Standard. Wipro Cat No.: LD99-281-XXX40PMWH or equivalent to approved make list

MR E- 9 : Supply, installation, testing & commissioning of Pendant Mounted Round Led Downlighter consuming a system wattage of 18W (±10%) & the luminaire shall be with system efficacy ≥ 95 lm / W. Housing: Extruded Aluminium Powder Coated. IP20 , Optics: PMMA/Polysterene Diffuser. The operating CCT shall be 4000K with CRI of ≥80. The luminaire shall be with BIS Registered electronic driver with input voltage range of 150 to 270V , THD ≤ 10% & PF ≥ 0.9, 50,000 Hrs LED Life with L70 Criteria. The LED Driver shall be easily avaiable in India for repair and service. The LED shall be SMD type. Luminaire shall have minimum surge protection of 2KV.The luminaire shall be with following certifications: LM79 & LM80 issued by LED manufacture along with Photo Biological Safety Standard. Wipro Cat No.: LD99-281-XXX40PMWH

MR - 10 : Supply, installation, testing & commissioning of Pendant Mounted Round Led Downlighter consuming a system wattage of 30W (±10%) & the luminaire shall be with system efficacy ≥ 95 lm / W. Housing: CRCA Powder Coated. IP20 , Optics: PMMA/Polysterene Diffuser. The operating CCT shall be 4000K with CRI of ≥80. The luminaire shall be with BIS Registered electronic driver with input voltage range of 150 to 270V , THD ≤ 10% & PF ≥ 0.9, 50,000 Hrs LED Life with L70 Criteria. The LED Driver shall be easily avaiable in India for repair and service. The LED shall be COB Type. Luminaire shall have minimum surge protection of 2KV.The luminaire shall be with following certifications: LM79 & LM80 issued by LED manufacture along with Photo Biological Safety Standard. Wipro Cat No.: LD30-201-36B-40-SS or equivalent to approved make list

MR - 11 : Supply, installation, testing & commissioning of 4ft Linear LED luminaire delivering an initial system lumen of 4000 lumens suitable for conduit suspension & the luminaire shall be with system efficacy ≥ 100 lm / W. The luminaire Housing shall be made of Extruded Aluminium & the diffuser shall be of polycarbonate/PMMA. The operating CCT shall be 5700K with CRI of ≥80. The luminaire shall be with BIS Registered electronic driver with input voltage range of 150 to 270V , THD ≤ 10% & PF ≥ 0.95 , 50,000 Hrs LED Life with L70 Criteria, IP40. The LED Driver shall be easily avaiable in India for repair and service. The LED shall be SMD type. Luminaire shall have minimum surge protection of 2KV.The luminaire shall be with following certifications: LM79 & LM80 issued by LED manufacture along with Photo Biological Safety Standard. Wipro Cat No.: LL24-541-XXX-57-CD or equivalent to approved make list

MR E- 12 : Supply, installation, testing & commissioning of Recessed Round Led Downlighter consuming a system wattage of 6W (±10%) delivering an initial system lumen of 600 lumens & the luminaire shall be with system efficacy ≥ 100 lm / W. Housing: Die Cast Aluminium. IP20 , Optics: Reflector with Glass . The operating CCT shall be 4000K with CRI ≥80. The luminaire shall be with BIS Registered electronic driver with input voltage range of 150 to 270V , THD ≤ 15% & PF ≥ 0.9, 50,000 Hrs LED Life with L70 Criteria. The LED Driver shall be easily avaiable in India for repair and service. The LED shall be COB type. Luminaire shall have minimum surge protection of 2KV. Wipro Cat No.: LD98-900-038-40-XX or equivalent to approved make list

MR E - 13 : Supply, installation, testing & commissioning of Recessed Round Led Downlighter consuming a system wattage of 12W (±10%) delivering an initial system lumen of 1200 lumens & the luminaire shall be with system efficacy ≥ 100 lm / W. Housing: Die Cast Aluminium. IP20 , Optics: Reflector with Glass . The operating CCT shall be 4000K with CRI ≥80. The luminaire shall be with BIS Registered electronic driver with input voltage range of 150 to 270V , THD ≤ 15% & PF ≥ 0.9, 50,000 Hrs LED Life with L70 Criteria. The LED Driver shall be easily avaiable in India for repair and service. The LED shall be COB type. Luminaire shall have minimum surge protection of 2KV. Wipro Cat No.: LD98-181-038-40-XX or equivalent to approved make list

MR E- 14 : Supply, installation, testing & commissioning of Deep Recess Mounted Round Led Downlighter low UGR consuming a system wattage of 15W (±10%) & the luminaire shall be with system efficacy ≥ 100 lm / W. Housing: Die Cast Aluminium. IP40 , Optics: PMMA/Polysterene Diffuser. The operating CCT shall be 4000K with CRI of ≥80. The luminaire shall be with BIS Registered electronic driver with input voltage range of 150 to 270V , THD ≤ 10% & PF ≥ 0.9, 50,000 Hrs LED Life with L70 Criteria. The LED Driver shall be easily avaiable in India for repair and service. The LED shall be SMD type. Luminaire shall have minimum surge protection of 2KV.The luminaire shall be with following certifications: LM79 & LM80 issued by LED manufacture along with Photo Biological Safety Standard. Wipro Cat No.: LD06X-171-XX-40-XX or equivalent to approved make list

MR E - 15 : Supply, installation, testing & commissioning of DALI Dimmable Recess Mounted Linear Led Fixture Suitable for techzone ceiling, consuming a system wattage of 29W (±10%) & the luminaire shall be with system efficacy ≥ 95lm/W. Housing:MS Powder Coated . IP20 , Optics: PMMA/Polysterene Diffuser. The operating CCT shall be 5700K with CRI of ≥80. The luminaire shall be with BIS Registered electronic driver with input voltage range of 150 to 270V , THD ≤ 10% & PF ≥ 0.9, 50,000 Hrs LED Life with L70 Criteria. Dimension 1195mm X 145mm. The LED Driver shall be easily avaiable in India for repair and service. The LED shall be SMD type. Luminaire shall have minimum surge protection of 2KV.The luminaire shall be with following certifications: LM79 & LM80 issued by LED manufacture along with Photo Biological Safety Standard. Wipro Cat No.: Techzone ( DALI) or equivalent to approved make list

MR E - 16 : Supply,installation,testing & commissioning of 9W IP 65 Grade Round Fixture made of ABS Plastic housing with CRCA Reflector and HET Diffuser suitable for Balcony. Equivalent to WIPRO Cat: LW01-101-XXX-60-XX or equivalent to approved make list

MR E - 17 : Supply ,installation,testing & commissioning of Architectural suspended lights made of Aluminium Alloy. WIPRO Cat LM87-D320-BLGD or equivalent to approved make list

MR E - 18 : Supply of DALI Controller along with Power Supply Suitable to Dim Fixtures from 0 to 100% and can create 4 Lighting Scenes. Similar to WIPRO HELVAR 191GW+290W+402 or equivalent to approved make list

MR E - 19 : Supply,Installation,testing & commissioning of ARCUS Step Light Compact,robust, non-corrosive aluminium body 4W LED steplight with high lumen output LEDs that enhancesthe safety and architectural design of step and entranceareas. WIPRO LT50-050-XXX-30-XX or equivalent to approved make list

MR E - 20 : Supply,installation,testing & commissioning of ARCUS Inground Light Inground burial 12W uplight Aluminium die castlight with high purity lens for illuminating pathways enhancing the safe and vibrant area. WIPRO LI20-111-030-30-XX _C-S-2C-IP67+LPV-35-12/24 or equivalent to approved make list

MR E - 21 : Supply installation,testing & commissioning of ARCUS aluminium housed 12W LED wall light with high illumination and soothing experience.WIPRO LW33-101-025-30-XX or equivalent to approved make list

MR E - 22 : Supply ,installation,testing & commissioning of 10W Track Light Garnet Similar to WIPRO Garnet Cat No. D161027 or equivalent to approved make list

MR E - 23 : Supply ,installation,testing & commissioning of Track 1mtr Long Similar to WIPRO Garnet Cat XTS5100 or equivalent to approved make list

MR E - 24 : Supply ,installation,testing & commissioning of 12W LED Square Surface Light similar to WIPRO Garnet Cat DB21240 or equivalent to approved make list

MR E - 25 : Supply ,installation,testing & commissioning of 5W LED Trimless deep recessed Light similar to WIPRO Garnet Cat D150527 or equivalent to approved make list

MR E - 26 : Supply ,installation,testing & commissioning of 3W LED Spot Light similar to WIPRO Garnet Cat D340327 or equivalent to approved make list

SUB HEAD-:Air Purification System

MR E - 27 : Supply, Installation, Testing and commissioning of Air Purification system in the specified areas where AHU/VRV/ Cassette /Hi-wall / Ductable units etc are installed , so as to improve Indoor air quality by using Bi-polar Ionization technology, producing equal amounts of positive and negative ions. Project design should meet standard ASHRAE 62.1 IAQ Procedure for energy saving. System should kill microorganism and pathogens, remove Odour, VOC and reduce dust particle /particulate matter / PM2.5 /PM 10. The product should be UL / Intertek listed. Product should have minimal or negligible pressure drop & low power consumptions. Hi Wall Unit

( a ) 1.3 TR to 1.45 TR

Cassette Unit

(b) 2.0 TR to 3.2 TR

SUB HEAD-:Cables

MR E - 28 : Supply of following sizes of 1.1 KV grade multicore Aluminium armd conductor XLPE insulated steel armoured cable confirming to IS :7908 (Part-1)/1988 with latest amendments & complete all as required.

(a) 70 Sq.mm 3.5 core

(b) 16 Sq.mm 4 core

(c ) 10 Sq.mm 4 core

(d ) 6 Sq.mm 3 core

SUB HEAD-:Telephone

MR E - 29 : Providing, fixing connecting and testing of under noted size of solderless telephone tag block Krone make in surface/recess in wall required size of M.S. box with hinged lockable cover duly stove enamel painted.

30 pair tag block

MR E - 30 : Providing, laying connecting and testing of multi-core telephone armoured cable of conductor size 0.5mm dia annealed copper conductor PVC insulated PVC sheathed jelly filled (as per DOT specification) cable as required

20 Pair telephone armoured cable

SUB-HEAD -: DG SETS

MR E - 31 Supply, Installation Testing and Commissioning of silent type Diesel Generating along with having Prime Power Rating of minimum 62.5 KVA 415 Volts at 1500 RPM, 0.8 lagging power factor at 415 volt suitable for 50 Hz, 3 phase system and consisting of the followings:

a) Diesel Engine

Diesel Engine 4 Stroke water cooled electric start for suitable BHP at 1500 R.P.M. suitable for above output at 40 Degree Turbocharged and air-to-air charge cooled, Radiator Cooled, 4 Stroke, heavy duty, power generation diesel engine as per IS 1002/BS5514/ ISO3046, capable of taking 10% over loading for one hour after 12 hours of continuous operation at 50 deg C. The engine will be fitted complete with all following accessories.

AMF Panel

MR E - 32 Supply of Standard AMF Panel as following , including 100A MCCB for Manual Panel inside DG canopy & separate Power panel having two contactor AC1duty 125A rating for DG & Mains, outside DG canopy, suitable for control voltage 12V DC. Battery charger panel mounted , trickle boost type 8A, 12V DC O/P.

MR E - 33 :Supplying and fixing of undernoted 'B' class MS pipe for DG exhaust complete with bends, elbow, flanges etc. as required.

100 mm dia pipe

MR E - 34 :Supply and fixing of 50mm thick compressed mineral wool insulation (Rock wool) for D.G. exhaust pipe with 22 gauge aluminium sheet cladding etc. as required for the under mentioned dia pipe.

100 mm dia pipe

MR E - 35 : Fabrication of supports for exhaust pipe, fuel pipe or for any other purpose out of M.S. structural steel including supplying and applying of enamel paint of approved shade after one coat of steel primer of reputed company.

SUB HEAD-:HVAC

Y-JOINTS:

MR E - 36 : Supply Installation, testing, commissioning of Y-joints of required size for refrigerant piping as per manufacturer standards. (Y Joints)

CONTROLLER :

MR E - 37 : Supply ,installation,testing and commissioning of Main Intelligent central controller system suitable for 32 indoor units to operate, monitor, on/off, temperature setting etc. The controller shall be Centralised control system for indoor units.

DRAIN PIPING :

MR E - 38 :Providing and fixing of PVC drain pipe of 10 Kg /m3 complete with 6mm thick closed cell nitrile rubber insulation, fittings, supports, valves as per specifications & drawings.

( a ) 25mm dia OD

( b ) 32mm dia OD

( c ) 40mm dia OD

Control wire

MR E - 39 : Supply, laying, affecting connections and Testing of the following sizes of control cum transmission wiring to be laid in PVC conduits between indoor units and outdoor units. 2CX1.5 Sqmm copper wire

INLINE FAN

MR E - 40 : Supply installtion & commissioning of inline fan with casing shall be of plastic suitable thickness , impeller shall be of mixed flow, factory matched to the electrical motor of suitable rating single phase 230 Volt , 50 to 60 Hz, class B , IP 44 protection . The fan should include electrical termination, mounting with necessary galvanised dipped supports , flexible connections if necessary, including all accessories.

( a ) 600 cfm capacity with 20 mm static pressure

( b ) 500 cfm capacity with 20 mm static pressure

( c ) 400 cfm capacity with 20 mm static pressure

( d ) 350 cfm capacity with 20 mm static pressure

( e ) 250 cfm capacity with 15 mm static pressure

( f ) 150 cfm capacity with 15 mm static pressure

Propeller Fan

MR E - 41 : Supplying, installing, testing and commissioning of Fixed Speed Propeller Fans. The scope of supply includes all accessories including flanges, supports, Baffels, Weather proetction louvres, vibration mountings etc.

100 mm dia suitable for 220±6% volts 50 cycles, 1 phase AC supply.

FANS FOR NORMAL Ventilation

MR E - 42 :Supply, Installation, Testing & Commissioning of long casing(GSS) Vane Axial flow type supply air fans complete with aluminium alloy blades with aerofoil design, bird screen, flexible connection & gravity louvers at outlet. Motor shall be of 415 + 10% volts, 50 Hz. Sound level at 3mt distance from fan outlet shall not be more than 80db(A) (Room Condition). Capacity shall be as follows & as per detailed technical specification: Fans should be AMCA certified.

(a) 4500 cfm capacity with 15 mm static pressure

(b) 410 cfm capacity with 10 mm static pressure

MR E - 43 :Supplying, installing and testing of exhaust air aluminium louvers(40mm deep louver) with bird screen complete as per specification & drawings.

MR E - 44 :Supplying & fixing of powder coated extruded aluminium Exhaust Air Grills (150x150mm) complete as required.

MR E - 45 :Supplying & fixing of Canvas connection as per require & specifications.

SUBHEAD-: Video Surveillance System(IP CCTV)

MR E - 46 :Supplying, installation, testing and commissioning of 2 megapixels resolution Network Dome Camera for true HD quality images,2.8 – 12 mm varifocal lens,True Day/Night (TDN) functionality for true color image ,Motion Detection 4 Zones, Multi- Level Sensitivity Privacy Zones 4 Zones,Snapshoot Support JPEG format Password Protection Support Character Display Support(Channel /Date) ONVIF Yes,IR Illumination20-30M IR illuminators for clear images in low light conditions Wide Dynamic Range 3D noise reduction for sharper images and lower bandwidth use in low light ONVIF compliant complete in all respect.

MR E - 47 : Supply, installation, testing and commissioning of 2 megapixels resolution Network Bullet camera camera,Imager 1/2.8”SONY 2.43 mega low illumination CMOS,Video Compression. .H.264/MJPEG,Day/Night .Mechanical ICR,Minimum Illumination-0Lux/F1.4(IR ON) IR Illumination-40-50M,,Electronic Shutter-Auto/Manual(1/25~1/10000) Lens 2.8 – 12 mm varifocal lens,Resolution Main-stream:D1/Q1080P(960*540)/HD720P/ HD1080P 1-25/30fps,Digital Noise Reduction-3D,Wide Dynamic Range-Digital WDR Motion Detection -4 Zones, Multi- Level Sensitivity,Privacy Zones-4 Zones,Snapshoot-Support JPEG format,Password Protection-Support,Character Display-Support(Channel /Date).Regulatory Emissions-FCC Part 15 CE: EN55022,Immunity -CE: EN50130-4,IP Rating- IP66 rated enclosure to protect against dust and water damage ONVIF compliant .

MR E - 48 :Supply, installation, testing and commissioning of Network Video Recorder , Live view/Resolution 5MP/3MP/1080p/720p,Motion Detection Control Privacy Mask Control. USB interface-1 × USB 2.0 and 1 × USB 3.0,Security-HTTPS, SSL, Watermark, User Authentication, Miscellaneous-N+1 hot spare. Alarm in/out -4 / 1,Network interface-1 RJ-45 10 /100 /1000 Mbps self-adaptive Ethernet interface, Security-HTTPS, SSL,Video/Audio output-VAG,HDMI and Audio. Watermark, User Authentication,Incoming bandwidth-100Mbps,Outgoing bandwidth-80Mbps,HDMI output,VGA Output,Protocol-IPv4, IPv6, TCP/IP protocol, PPPoE, DHCP, DNS, DDNS, NTP, SADP, SMTP, SNMP, NFS, and iSCSI are supported.TCP, UDP and RTP for unicast, UPnPTM, ONVIF, PSIA,Support 16 IP Camera, 2 SATA interfaces for 4 HDDs Upto 4TB for each disk.

MR - 49 :Supply, installation, testing and commissioning of Enterprise Class 4TB Hard Disck.

MR - 50 :Supply, installation, testing and commissioning of Video Management System (VMS) software shall be used to view live and recorded video from capture cards and IP devices connected to local and wide area networks. The VMS software shall have a client/server-based architecture that can be configured as a standalone VMS system with the client software running on the server hardware and/or the client running on any network-connected TCP/IP workstation. Multiple client workstations shall be capable of simultaneously viewing live and/or recorded video from one or more servers. Multiple servers shall also be able to simultaneously provide live and/or recorded video to one or more workstations. The VMS server software shall also have the ability to be installed on an IP edge device—such as an IP camera or encoder that allows for 3rd party applications—allowing the device to serve as both a server and IP video recording device.The VMS shall not charge for the number of concurrent clients (min. 50 thick clients and 16 mobile clients to be provided along with VMS).

MR E - 51 : Supplying, Installation,Testing & Commissioning of 32 " LED Full HD TV Resolution 1920 x 1080 ,Contrast Ratio (Typical) 5000:1,Built-in Speaker (10W + 10W), Magic Clone (to USB), Auto Source Switching & Recovery, Lamp Error Detection, Super Clear Coating, Temperature Sensor, Plug and Play (DDC2B), Pivot Display, Clock Battery, PIP/PBP, Video Wall (10x10), Image Rotation, Button Lock, HDCP Support, Smart Scheduling, Smart F/W update, Built-In MagicInfo Premium-Swith Mounting Brackets as per Technical Specification complete in all respect.

MR E - 52 : Supply, installation, testing & commissioning of Client Workstation having Intel Core i5 orginal motherboard, 16 GB RAM, Video graphics card 2 GB Licensed Windows 8 Professional (64 bit) and 1 TB Hard Disk with Web camera,Printer and finger print scanner.

EPABX System

MR E - 53 : Supply Installation, Testing and Commissioning of EPABX . Multi slot Wall/Rack Mountable Expandable upto 128 Ports Presently Configuration as Below CO Line - 4Nos. SIP Extension - 6Nos Digital Extension Circuits - 5Nos Analog Extension Circuits - 50 Nos.

MR E - 54 : Supply Installation Testing and Commissioning of Digital Phone 12 key display Backlit keypad Hands-free working Easy to use soft keys / LCD prompts on display model Directory dial key 1000 system, 1000 group, 10 personal, 600 phone book Conference key Wall mountable Message waiting indicator .

MR E - 55 : Supply Installation Testing and Commissioning of Digital Phone 6 key display Backlit keypad Hands-free working Easy to use soft keys / LCD prompts on display model Directory dial key 1000 system, 1000 group, 10 personal, 600 phone book Conference key Wall mountable Message waiting indicator .

MR E - 56 : Supply Installation, Testing and Commissioning of Analog CLI Phone with handsfree.

MR E - 57 : Supply Installation Testing and Commissioning of 15U Rack including all accessories as complete as required.

MR E - 58 : Supply Installation Testing and Commissioning of 24 port POE Switch with SPF/Giga port one year support pack as required.

MR E - 59 : Supply installation testing and Commissioning of 1x2KVA online True online double conversion with inbuilt isolation transformer,Single Phase Input/Single Phase Output.with SMF Batteries suitable for 30Mint backup.Capicity 2kVA/1.8kW ,Input voltage range 170-280V Input power factor More Than 0.99 input THDi Less than 5% ,output voltage 230V AC regulation +/- 1% output wave form sinusidal.Output THDu Less than 3% for linear load Less than 5% for non linear load Crest factor 3 : 1 overload110% for 10 min 130% for 1 min battery voltage 96VDC battery charging Advanced Battery Management Battery bank sizing ( min VAH 2688 ) overall efficiency At least 88% in UPS Mode ,communication port RS232/USB/EPO.UPS shall have SNMP certification BIS operating temperature 0 – 40 deg C relative humidity 95% Non condensing.

SUB HEAD- : LIFT

MR E - 60 :Supplying, installation, testing & commissioning of 10 Passenger (680 Kg), Gearless type,Machne room-less passenger lift of having contract speed 1 m/s serving different floors in the lift shaft as per detailed specifications as under and additional details given in schedule of technical particulars. Provisions of General CPWD specifications for lift works are to be followed.

Speed - 1.0 Metre/Sec.

Floor - B+S+4 = 6 stops

Travel - 16.0 Mtr. (Approx.)

Stop & Opening - 6 Stops & 6 Openings (One side only)

Type and Position of Machinery - Gearless type, Machine Room-less

Controller - Micro processer based AC variable voltage & variable frequency Control

Automatic rescue device complete with dry maintenace free batteries as required.

Operation - Microprocessor based Simplex Full Collective with / without attendant.

Power- 415 V ±10%, 3 Phase, 50 Hz. Or as per manufacturer specifications

Car panel finish - Scrach resistant Stainless steel with side walls Pre-laminated wooden finish as approved by E/I.

Car door - Power operated centre opening horizontal sliding stainless steel AISI441Scratch resistant

Door operation - Full Height Infra-red cross-multi beam

Landing doors -2 panel Centre opening, stainless steel scratch resistant at all floors. It must be fire-rated for minimum 1-Hrs and supplier must provide the certiifcate for the same alongwith material supply.

Car operating Panel / Landing operating panel - Car operating panel with braile symbol luminous buttons and braile illuminated push buttons on all landing in Stainless Steel Hair line finish.

Hand rail - Shall be SS finish fixed above 900mm from the car-floor level on rear-wall and side wall.

Voice announcement system - In car to announce the position of the elevetor in hoist way as the car passes or stop at a floor served by the elevator

Intercom system - 3-way intercom

Clear Opening of Doors - 800mm x 2200mm (Wide x Height)

Lift Car inside size - 1300 x 1350 x 2400 ( Width x depth x height).

Size of Lift Well - 2000 x 1900 mm(Width x Depth)

Door Entrance -800mm

SUB HEAD-:External Lighting

MR E - 61 : Supply,Installation,testing and commissioning of LED bollard 800mm height with system wattage of 8W delivering minimum system lumen of 560 lumens.CRCA powder coated housing ,with PMMA diffuser symetrical distribution. The operating CCT shall be 5700K with CRI of ≥70.The lumiaire shall be with BIS registered elctronic driver with Input voltage range of 180 to 270V , internal driver with efficiency ≥ 80%, THD≤25% & PF ≥ 0.95 ,minimum surge protection of 2KV, 50,000 Hrs LED Life with L70 Criteria, IP65 Ingress protection and ambient operating tempretature 0-45° C. Similar or equivalent to Wipro Cat No.:CRLA11008HP57-08 or equivalent to approved make list

MR E - 62 : Supply,Installation,testing and commissioning of post top Luminaire consuming a system wattage of 35W (±10%) & the luminaire shall be with system efficacy ≥ 95lm/W. Housing: Die Cast Aluminium . IP65 , Optics: Acrylic Clear Diffuser. The operating CCT shall be 5700K with CRI of ≥70. The luminaire shall be with BIS Registered electronic driver with input voltage range of 150 to 270V , THD ≤ 10% & PF ≥ 0.9, 50,000 Hrs LED Life with L70 Criteria.The LED Driver shall be easily avaiable in India for repair and service. The LED shall be SMD type. Luminaire shall have minimum surge protection of 4KV.The luminaire shall be with following certifications: LM79 & LM80 issued by LED manufacture along with Photo Biological Safety Standard. Wipro Cat No.:LP07-431-XXX-57-CL or equivalent to approved make list

MR E - 63 : Supply,Installation,testing and commissioning of Bulkhead Light 10 Watt. IP-65

SUB HEAD-:PA System

Recreational cum training area

MR E - 64 : Supply, Installation, Testing and Commissioning of 16Watt Ceiling speaker with Frequency response of 95 Hz‐17KHz(±3 db); Sensitivity of 84 db SPL @1W,1m; Maximum SPL:‐ 96 db SPL @ 1m; Power handling capacity of 16W continuous; Impedence:‐ 8Ω (Transformer by passed), 100V:‐ 2,4,8,16W, 7V:‐ 1,2,4,8,16W; Driver:‐ 2.25" full‐range driver; Enclosure:‐PC/ABS (white), Polypropylene(black); Dispersion angle:‐ 170˚ conical.

MR E - 65 : Supply, Installation, Testing and Commissioning of Class D Zone amplifier with power as 2*120W@ 70/100V; Frequency response of 55Hz to 20kHz(±3 db); THD <0.3%; 1 unbalanced AUX input, 1 balanced mic/line page input, 2 unbalanced and 2 balanced line inputs; Dynamic range is of 88 dB.

MR E - 66 : Supply, Installation, Testing and Commissioning of 8 channel mixer with 4 mono inputs, 3 stereo input, 2tk in/out, 1 aux send, 2 compressor(ch1‐ch2), 3 band/2 band EQ, Frequency response:‐ 10Hz to 55KHz(±3 db); THD+N:‐ 0.03%; Max input SNR:‐<‐100 dbr.

MR E - 67 : Supply, Installation, testing and commissioning of Goosneck Microphone of 12" to 16" with Cardioid polar pattern, Frequency Response : 100 ‐ 20,000 Hz complete with base Stand of same make with on/off button, LED Indication for Mic Status, RFI/ GSM Shielding along with shock mount.

MR E - 68 : Supply, Installation, Testing and Commissioning of Digital Wireless Handheld Microphone with cardioid pick up pattern, operating on 1.9 GHz bandwidth, 256 bit AEC Encryption, AF Frequency response: 20 Hz‐20 kHz, Dynamic range: > 120 dB, Audio Sampling: 24 bit/48 kHz, RF Power: adaptive 200 mW , Receiver with front panel LCD/LED Display, 7‐band Graphic equalizer, LAN port for control and Monitoring, Complete as per the Specifications.

MR E - 69 : Supply, Installation, Testing and Commissioning of Digital Wireless Lapel Microphone with omni directional pick up Pattern, operating on 1.9 GHz bandwidth, 256 bit AEC Encryption, AF Frequency response: 20 Hz‐20 kHz, Dynamic range: > 120 dB, Audio Sampling: 24 bit/48 kHz, RF Power: adaptive 200 mW, Receiver with front panel LCD/LED Display, 7‐band Graphic equalizer, LAN port for control and Monitoring,, Complete as per the Specifications.

MR E - 70 : Supply, laying, Testing and Commissioning of 2 Core Shielded Microphone Cable.

MR E - 71 : Supply, Installation, Testing and Commissioning of Mettalic Podium with provision to place Interactive 23" or higher Tablet Monitor with Presentation Plate, document camera, Switcher, Amplifier, PC, etc complete with standard accessories complete as required.

MR E - 72 : Supplying, installation, testing and commissioning of 4K60 4:4:4 Twisted Pair transmitter with 1x HDMI input, 1x RS232/IR , Output: 1 x HDBaseT, Should support resolution of 4K or more, Power over HDBaseT, USB 2.0 Transmission, HDCP compliant.

MR E - 73 : Supplying, installation, testing and commissioning of 4K60 4:4:4 Twisted Pair receiver with 1x HDBaseT input, Output: 1 x HDMI, Should support resolution of 4K or more, Bidirection RS‐232 and IR control, USB 2.0 Transmission, HDMI 2.0 and HDCP 2.2 Support.

MR E - 74 : Supply, laying, testing & commissioning of 2 m HDMI patch cable

MR E - 75 : Supply, laying, testing & commissioning of Cat 6 shielded pair cable

Multipurpose Room and conference Room

MR E - 76 : Supply, Installation, testing and commissioning of Digital Signal processor with 12 Input x 8 output with AEC, 2‐line VoIP, USB audio interface, 5 In / out GPIO connection, A/D and D/A Converters: 24‐bit, Frequency Response: 20 Hz to 20kHz (+0.3 dB/‐ 0.1 dB), THD+N: 0.02 % , Channel Separation (Crosstalk): < ‐70 dB, Dynamic Range: > 105 dB, along with Dante 64x64, primary/secondary AV over Ip channel.

MR E - 77 : Supply, Installation, Testing and Commissioning of Digital Wireless Handheld Microphone with cardioid pick up pattern,operating on 1.9 GHz bandwidth, 256 bit AEC Encryption, AF Frequency response: 20 Hz‐20 kHz, Dynamic range: > 120 dB, Audio Sampling: 24 bit/48 kHz, RF Power: adaptive 200 mW , Receiver with front panel LCD/LED Display, 7‐band Graphic equalizer, LAN port for control and Monitoring, Complete as per the Specifications.

MR E - 78 : Supply, installation, testing and commissining of 5000 Lumens Laser WUXGA projector with 3 LCD technology,Aspect ratio ;16 :10, Laser life : 20000 hrs,input ports : 1x HDMI , 1x VGA, 1x HDBaseT

MR E - 79 : Supply, Installation, testing & commissioning 2 m VGA-VGA patch Cord

Public address System

MR E - 80 : Supply, Installation, Testing and Commissioning of EN54‐16/BS‐ 5839/EN‐60849 compliant and certified digital controller, with full DSP functionality as per the specifications in part‐I. It shall support single line switching or redundant group A/B switching, amplifier redundancy, 4 x 100V audio inputs with output of 12 speaker line or more. System should log minimum 5000 fault/ warning/event conditions should be reported with the possibility to look real‐time into the logging and save the log with logging tools. Built in message manager for 100 emergency/business calls more than 60 minutes. Should be able to send 2 different prerecorded messages simultaneously. Impedance measurement and Pilot Tone supervision for speaker line monitoring. Shall be able to handle up to 2000 Watt load, 12 or more routers, 16 call stations, upto 400 speaker zones with required accessories.

MR E - 82 : Supply, Installation, Testing and Commissioning of EN54‐16/BS‐ 5839/EN‐60849 certified high efficiency minimum 1000 W, Class D, multichannel digital amplifier as per the Specifications in tender part‐I with limiters for audio input level, RMS output power, protection against high temperature, DC short circuit, mains under‐voltage, DC supply under‐voltage protection, inrush current limiter with required accessories. The item should include the required cabling/wiring with proper termination etc.

MR E - 83 : Supply, installation, testing and commissioning of 15W high efficiency circular horn loudspeaker, High‐efficiency driver, Max. Power: 22.5W, Power tapping: 15 / 7.5 / 3.75 W, SPL at 15 W (1kHz,1m): 115 dB, Frequency response: 500Hz‐5kHz, Rated impedence: 1667 Ω, Opening angle at 1kHz/4kHz(‐6dB): 130 ⁰ H x 50 ⁰ V, Water and dust protected to IP 65, Safety: EN 60065.

MR E - 84 : Supply and fixing of connectors and necessary accessories, complete as per the specification.

Bidder Name

Amount

M/s Narayan Kumar(GSTN-NA)

S K Integrated Consultants(GSTN-NA)

GARG BUILDERS(GSTN-NA)

SUNEHARI BAGH BUILDERS PVT. LTD.(GSTN-NA)

M/s. JYOTI SARUP MITTAL(GSTN-NA)

Bidder Name

Amount

M/s Narayan Kumar(GSTN-NA)

S K Integrated Consultants(GSTN-NA)

GARG BUILDERS(GSTN-NA)

SUNEHARI BAGH BUILDERS PVT. LTD.(GSTN-NA)

M/s. JYOTI SARUP MITTAL(GSTN-NA)

SUNEHARI BAGH BUILDERS PVT. LTD.

S K Integrated Consultants

M/s. JYOTI SARUP MITTAL

GARG BUILDERS

SUNEHARI BAGH BUILDERS PVT. LTD.

S K Integrated Consultants

M/s. JYOTI SARUP MITTAL

GARG BUILDERS

SUNEHARI BAGH BUILDERS PVT. LTD.

S K Integrated Consultants

M/s. JYOTI SARUP MITTAL

GARG BUILDERS

SUNEHARI BAGH BUILDERS PVT. LTD.

M/s. JYOTI SARUP MITTAL

M/s Narayan Kumar

GARG BUILDERS

M/s Narayan Kumar

M/s. JYOTI SARUP MITTAL

GARG BUILDERS

SUNEHARI BAGH BUILDERS PVT. LTD.