PROVISION OF DG SET AT HEMRL PUNE

Amount

Supply, laying and testing cable XLPE Insulated ,screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor including connecting the cable with suitable lugs/thimbles and testing complete all as specified and directed by Engr-in-Charge for following sizes :-

a) 3.5 core 35 sqmm

b) 3.5 core 70 sqmm

c) 3.5 core 95 sqmm

d) 3.5 core 120 sqmm

e) 3.5 core 150 sqmm

f) 3.5 core 185 sqmm

g) 3.5 core 240 sqmm

h) 3.5 core 300 sqmm

j) 3.5 core 400 sqmm

Excavation in trenches not exceeding 1.5 mtr wide and not exceeding 1.5 mtr deep for taking out/laying of HT/ LT under ground cable and getting out in the following type of earth stata complete all as specified and as directed:-

a) Soft / loose soil

b) Hard / dense soil

c) Soft / Disintegrated rock

d) Hard rock

Returning, filling in including spreading, leveling, watering and well ramming in layers not exceeding 25cm in soils complete all as specified and directed.

Removing surplus excavated soil to a distance not exceeding 50m depositing where directed at a level not exceeding 1.5m above the starting point complete all as specified and directed.

Supply and lay in trenches Un- reinforced precast concrete cable cover class LV type 1 flat ISI marked, size 250 x150 x 40 mm for cable protection all as specified and directed.

Sand (Stone crushed sand) in cable trenches as cushioning to cables including spreading and punning down all as per clause No 3.21 of SSR Part - I (2009) complete all as specified and directed. Note : Punned thickness shall only be measured and paid

Cutting Bituminous road and making good the same including supply of extra quantities of materials i.e. aggregate, moorum screening, red bajri and labour required.

M & L GI tube, light grade 100 mm dia bore pipe with all fittings, complete, fixed to walls, pole ceiling or laid in trenches for cable protection complete all as specified and directed.

M & L GI tube, light grade 80 mm dia bore pipe with all fittings, complete, fixed to walls, pole ceiling or laid in trenches for cable protection complete all as specified and directed.

M & L GI tube, light grade 50 mm dia bore pipe with all fittings, complete, fixed to walls, pole ceiling or laid in trenches for cable protection complete all as specified and directed.

Supply, installation, commissioning & testing of silent, Diesel engine driven factory assemble, generating set of capacity 40 KVA, 3 phase, 4 wire, 50 Hz, 1500 RPM complete with Engine and alternator mounted on a common MS fabricated base frame with AVM pads, Acoustic enclosure, relay panel for automatic starting on mains failure safety control and metering equipment mounted on & including common base frame and installed on PCC/RCC foundation as recommended by manufacturer and approved by GE and suitable for ambient conditions at Pune, environmental eco-friendly as per CPCB IV+ norms including the following all as specified and directed. Note: PCC foundation work as per manufacture instructions, anti-vibration pads and other standard accessories and comprising of the following complete all as specified and directed

Diesel Engine: Multi Cylinders , Inline arrangement, Gross Engine power (HP) 52 and (KWm) 39, water cooled turbocharged with after cooled, rated output 1500 RPM and overspeed trip 1650 RPM, Engine Is with electric start, compression ignition, stroke cycle designed to run continuously at 1500 RPM conforming to IS 2002, ISO-3046, BS 5514 standards. Diesel engines should comply with CPCB IV +norms. The Diesel Engine are comprising of followings: (1) Radiator with Fan (2) Fuel Injection equipment with Electronic Governor having CRS (Common Rail system) and DG performance class G3 (3) Dry type air cleaner (4) Exhaust silencer type NA, Max allowable backpressure (kPa) 17, Exhaust temperature (Deg C) 550, (5) Lub oil filter (Spin on type), (6) Fuel oil filter (Spin on type), (7) 24V electric starting system, (8) Battery charging alternator, (9) Stop Solenoid, (10) Lube Oil pressure Gauge, (11) Water Temperature Gauge, (12) lube oil temperature Gauge, (13) Battery voltage, (14) Extended life coolant, (15) First fill lube Oil

Alternator: Alternator type 4P, rotating field, automatic voltage regulator and voltage regulation +/- 1%, suitable for continuous duty operations rated at 1500 RPM, 415V, 0.8PF, 50 Hz, current (3Ph) Amps-56 in SPDP enclosure, Self-Excited & Self-regulated, Brushless, ‘H’ class insulation, temperature rise (Deg C) 125, coupling type Fle Disc, unbalanced load capability 25% of rated amps, Floor mounted with anti-friction Sealed ball bearing on end. Alternator charging 12V DC/35A, the alternator conforms to IS: 13364 (Part-II) suitable for tropical condition including making cable connection.

Acoustic Enclosure: (a) Specially designed to meet stringent MoEF / CPCB norms of 75 dBA @ 1 Mtr at 75% Load under free field conditions. (b) The followings are some technical features of Acoustic Enclosure: (1) The Enclosure is modular in construction. (2) Base Frame is made of Sheet metal. (3) Durable industrial locking system is provided on Doors. (4) Door Gaskets are made in high quality EPDM material. (c) Corrosion Resistance: To make the Enclosure weather proof:- (1) All sheet metal parts/components are hot dipped in seven tanks process, Pretreated and Passivated (2) Sheet metal components are with Pretreated and Passivated Base Powder Coated. (3) Base Frame is Epoxy Coated/Powder Coated. (4) Zinc Passivated Hardwares are used to avoid rusting. acoustic insulation: (1) Sound proofing of the Enclosure is done with Quality Rockwool confirming to IS:8183 Standard. (2) Acoustic foam shall be fire retardant and fire resistant. (3) Attenuates are provided to control sound at entry and exit of container. (4) Specially designed Residential Silencer is provided.

(d) Ventilation And Air Circulation: Exhaust pipe inside Enclosure is thoroughly insulated by Cladding of Rock wool and Sheet. (e) ELECTRICAL: Neutral Body Earthing points at the sides of enclosure are isolated through Moulded compound. (f) SAFETIES: Emergency Push button to Stop the DG set from outside, Low Fuel oil level, Low Lube oil pressure, Low Coolant Level, High Engine Temperature. The canopies being offered are for output of Noise Level ≤ 75 dbA at a distance of 1-meter average, as per the CPCB IV+ Norms. Batteries: 2 Nos. 12V 90Ah batteries with leads for electric starting. Paint: DG set and panel package will be painted with powder coated type paint. STANDARD GENSET CONTROLLER UNIT WITH CONTROL PANEL: - Genset Controller unit with totally enclosed, Steel Construction Control Panel suitable for indoor floor /wall mounting installation having standard safeties and display parameters.”

AMF PANEL: Supply, install, testing and commissioning of AMF Panel for 40 KVA DG Set factory made, outdoor cubical type as per IE/CPRI rules with IP-54 protection, dust and vermin proof, compartmentalised, made of 3.15 mm thick CRCA sheet, fixed on MS angle iron frame of 50 x 50 x 6 mm thick of required type for supporting double door both sides open type with necessary locking arrangement with slope roof on top duly painted with two coats of powder coated sense grey paint with seven tank process complete and having separate doors inside for accommodating all incoming/outgoing cables and other relevant standards mounted on and including provision of necessary plinth in PCC 1:3:6, type C1 for foundation and PCC pillars with suitable size of nut, bolts & washers grouted as required at site and as per manufacturer's instructions including provision of the following items complete all as specified and directed. (a) Bus bar with electrolytic copper bus bar (for Mains and DG supply incoming and outgoing) suitable for 100 amps capacity for 3 phase and neutral(TPN) (all connection inside the panel shall be through aluminium strip) connected duly supported with FRP insulators including colour code heat shrink insulating sleeves (b) Three phase 4 Pole, Power contractor, 63 Amps for ON-OFF the DG and mains supply -02 Nos (c) MCCB 63 Amps, 25KA for ON-OFF the DG and mains supply -02 Nos (d) MCCB 63 Amps, 25KA - 02 Nos.

Supply, installation, commissioning & testing of silent, Diesel engine driven factory assemble, generating set of capacity 82.5 KVA, 3 phase, 4 wire, 50 Hz, 1500 RPM complete with Engine and alternator mounted on a common MS fabricated base frame with AVM pads, Acoustic enclosure, relay panel for automatic starting on mains failure safety control and metering equipment mounted on & including common base frame and installed on PCC/RCC foundation as recommended by manufacturer and approved by GE and suitable for ambient conditions at Pune, environmental eco-friendly as per CPCB IV+ norms including the following all as specified and directed. Note: PCC foundation work as per manufacture instructions, anti-vibration pads and other standard accessories and comprising of the following complete all as specified and directed

Diesel Engine: Multi Cylinders, Inline arrangement, Gross Engine power (HP) 104 and (KWm) 78, water cooled turbocharged with after cooled, rated output 1500 RPM and overspeed trip 1650 RPM, Engine Is with electric start, compression ignition, stroke cycle designed to run continuously at 1500 RPM conforming to IS 2002, ISO-3046, BS 5514 standards. Diesel engines should comply with CPCB IV+ norms. The Diesel Engine are comprising of followings: (1) Radiator with Fan (2) Fuel Injection equipment with Electronic Governor having CRS (Common Rail system) and DG performance class G3 (3) Dry type air cleaner (4) Exhaust silencer type NA, Max allowable backpressure (kPa) 17, Exhaust temperature (Deg C) 550, (5) Lub oil filter (Spin on type), (6) Fuel oil filter (Spin on type), (7) 24V electric starting system, (8) Battery charging alternator, (9) Stop Solenoid, (10) Lube Oil pressure Gauge, (11) Water Temperature Gauge, (12) lube oil temperature Gauge, (13) Battery voltage, (14) Extended life coolant, (15) First fill lube Oil

Alternator: Alternator type 4P, rotating field, automatic voltage regulator and voltage regulation +/- 1%, suitable for continuous duty operations rated at 1500 RPM, 415V, 0.8PF, 50 Hz, current (3Ph) Amps-115 in SPDP enclosure, Self-Excited & Self-regulated, Brushless, ‘H’ class insulation, temperature rise (Deg C) 125, coupling type Fle Disc, unbalanced load capability 25% of rated amps, Floor mounted with anti-friction Sealed ball bearing on end. Alternator charging 12V DC/35A, the alternator conforms to IS: 13364 (Part-II) suitable for tropical condition including making cable connection.

Acoustic Enclosure: (a) Specially designed to meet stringent MoEF / CPCB norms of 75 dBA @ 1 Mtr at 75% Load under free field conditions. (b) The followings are some technical features of Acoustic Enclosure: (1) The Enclosure is modular in construction. (2) Base Frame is made of Sheet metal. (3) Durable industrial locking system is provided on Doors. (4) Door Gaskets are made in high quality EPDM material. (c) Corrosion Resistance: To make the Enclosure weather proof:- (1) All sheet metal parts/components are hot dipped in seven tanks process, Pretreated and Passivated (2) Sheet metal components are with Pretreated and Passivated Base Powder Coated. (3) Base Frame is Epoxy Coated/Powder Coated. (4) Zinc Passivated Hardwares are used to avoid rusting. acoustic insulation: (1) Sound proofing of the Enclosure is done with Quality Rockwool confirming to IS:8183 Standard. (2) Acoustic foam shall be fire retardant and fire resistant. (3) Attenuates are provided to control sound at entry and exit of container. (4) Specially designed Residential Silencer is provided. (d) Ventilation And Air Circulation: Exhaust pipe inside Enclosure is thoroughly insulated by Cladding of Rock wool and Sheet.

(e) ELECTRICAL: Neutral Body Earthing points at the sides of enclosure are isolated through Moulded compound. (f) SAFETIES: Emergency Push button to Stop the DG set from outside, Low Fuel oil level, Low Lube oil pressure, Low Coolant Level, High Engine Temperature. The canopies being offered are for output of Noise Level ≤ 75 dbA at a distance of 1-meter average, as per the CPCB IV+ Norms. Batteries: 2 Nos. 12V 90Ah batteries with leads for electric starting. Paint: DG set and panel package will be painted with powder coated type paint. STANDARD GENSET CONTROLLER UNIT WITH CONTROL PANEL: - Genset Controller unit with totally enclosed, Steel Construction Control Panel suitable for indoor floor /wall mounting installation having standard safeties and display parameters.”

AMF PANEL: Supply, install, testing and commissioning of AMF Panel for 82.5 KVA DG Set factory made, outdoor cubical type as per IE/CPRI rules with IP-54 protection, dust and vermin proof, compartmentalised, made of 3.15 mm thick CRCA sheet, fixed on MS angle iron frame of 50 x 50 x 6 mm thick of required type for supporting double door both sides open type with necessary locking arrangement with slope roof on top duly painted with two coats of powder coated sense grey paint with seven tank process complete and having separate doors inside for accommodating all incoming/outgoing cables and other relevant standards mounted on and including provision of necessary plinth in PCC 1:3:6, type C1 for foundation and PCC pillars with suitable size of nut, bolts & washers grouted as required at site and as per manufacturer's instructions including provision of the following items complete all as specified and directed. (a) Bus bar with electrolytic copper bus bar (for Mains and DG supply incoming and outgoing) suitable for 300 amps capacity for 3 phase and neutral(TPN) (all connection inside the panel shall be through aluminium strip) connected duly supported with FRP insulators including colour code heat shrink insulating sleeves (b) Three phase 4 Pole, Power contractor, 125 Amps for ON-OFF the DG and mains supply -02 Nos (c) MCCB 125 Amps, 25KA for ON-OFF the DG and mains supply -02 Nos (d) MCCB 125 Amps, 25KA - 02 Nos.

Supply, installation, commissioning & testing of silent, Diesel engine driven factory assemble, generating set of capacity 100 KVA, 3 phase, 4 wire, 50 Hz, 1500 RPM complete with Engine and alternator mounted on a common MS fabricated base frame with AVM pads, Acoustic enclosure, relay panel for automatic starting on mains failure safety control and metering equipment mounted on & including common base frame and installed on PCC/RCC foundation as recommended by manufacturer and approved by GE and suitable for ambient conditions at Pune, environmental eco-friendly as per CPCB IV+ norms including the following all as specified and directed. Note: PCC foundation work as per manufacture instructions, anti-vibration pads and other standard accessories and comprising of the following complete all as specified and directed

Diesel Engine: Multi Cylinders , Inline arrangement, Gross Engine power (HP) 122 and (KWm) 92, water cooled turbocharged with after cooled, rated output 1500 RPM and overspeed trip 1650 RPM, Engine Is with electric start, compression ignition, stroke cycle designed to run continuously at 1500 RPM conforming to IS 2002, ISO-3046, BS 5514 standards. Diesel engines should comply with CPCB IV+ norms. The Diesel Engine are comprising of followings: (1) Radiator with Fan (2) Fuel Injection equipment with Electronic Governor having CRS (Common Rail system) and DG performance class G3 (3) Dry type air cleaner (4) Exhaust silencer type NA, Max allowable backpressure (kPa) 17, Exhaust temperature (Deg C) 550, (5) Lub oil filter (Spin on type), (6) Fuel oil filter (Spin on type), (7) 24V electric starting system, (8) Battery charging alternator, (9) Stop Solenoid, (10) Lube Oil pressure Gauge, (11) Water Temperature Gauge, (12) lube oil temperature Gauge, (13) Battery voltage, (14) Extended life coolant, (15) First fill lube Oil

Alternator: Alternator type 4P, rotating field, automatic voltage regulator and voltage regulation +/- 1%, suitable for continuous duty operations rated at 1500 RPM, 415V, 0.8PF, 50 Hz, current (3Ph) Amps-139 in SPDP enclosure, Self-Excited & Self-regulated, Brushless, ‘H’ class insulation, temperature rise (Deg C) 125, coupling type Fle Disc, unbalanced load capability 25% of rated amps, Floor mounted with anti-friction Sealed ball bearing on end. Alternator charging 12V DC/35A, the alternator conforms to IS: 13364 (Part-II) suitable for tropical condition including making cable connection.

Acoustic Enclosure: (a) Specially designed to meet stringent MoEF / CPCB norms of 75 dBA @ 1 Mtr at 75% Load under free field conditions. (b) The followings are some technical features of Acoustic Enclosure: (1) The Enclosure is modular in construction. (2) Base Frame is made of Sheet metal. (3) Durable industrial locking system is provided on Doors. (4) Door Gaskets are made in high quality EPDM material. (c) Corrosion Resistance: To make the Enclosure weather proof:- (1) All sheet metal parts/components are hot dipped in seven tanks process, Pretreated and Passivated (2) Sheet metal components are with Pretreated and Passivated Base Powder Coated. (3) Base Frame is Epoxy Coated/Powder Coated. (4) Zinc Passivated Hardwares are used to avoid rusting. acoustic insulation: (1) Sound proofing of the Enclosure is done with Quality Rockwool confirming to IS:8183 Standard. (2) Acoustic foam shall be fire retardant and fire resistant. (3) Attenuates are provided to control sound at entry and exit of container. (4) Specially designed Residential Silencer is provided. (d) Ventilation And Air Circulation: Exhaust pipe inside Enclosure is thoroughly insulated by Cladding of Rock wool and Sheet.

(e) ELECTRICAL: Neutral Body Earthing points at the sides of enclosure are isolated through Moulded compound. (f) SAFETIES: Emergency Push button to Stop the DG set from outside, Low Fuel oil level, Low Lube oil pressure, Low Coolant Level, High Engine Temperature. The canopies being offered are for output of Noise Level ≤ 75 dbA at a distance of 1-meter average, as per the CPCB IV+ Norms. Batteries: 2 Nos. 12V 90Ah batteries with leads for electric starting. Paint: DG set and panel package will be painted with powder coated type paint. STANDARD GENSET CONTROLLER UNIT WITH CONTROL PANEL: - Genset Controller unit with totally enclosed, Steel Construction Control Panel suitable for indoor floor /wall mounting installation having standard safeties and display parameters.”

AMF PANEL: Supply, install, testing and commissioning of AMF Panel for 100 KVA DG Set factory made, outdoor cubical type as per IE/CPRI rules with IP-54 protection, dust and vermin proof, compartmentalised, made of 3.15 mm thick CRCA sheet, fixed on MS angle iron frame of 50 x 50 x 6 mm thick of required type for supporting double door both sides open type with necessary locking arrangement with slope roof on top duly painted with two coats of powder coated sense grey paint with seven tank process complete and having separate doors inside for accommodating all incoming/outgoing cables and other relevant standards mounted on and including provision of necessary plinth in PCC 1:3:6, type C1 for foundation and PCC pillars with suitable size of nut, bolts & washers grouted as required at site and as per manufacturer's instructions including provision of the following items complete all as specified and directed. (a) Bus bar with electrolytic copper bus bar (for Mains and DG supply incoming and outgoing) suitable for 300 amps capacity for 3 phase and neutral(TPN) (all connection inside the panel shall be through aluminium strip) connected duly supported with FRP insulators including colour code heat shrink insulating sleeves (b) Three phase 4 Pole, Power contractor, 200 Amps for ON-OFF the DG and mains supply -02 Nos (c) MCCB 200 Amps, 36KA for ON-OFF the DG and mains supply -02 Nos (d) MCCB 200 Amps, 36KA - 02 Nos.

Supply, installation, commissioning & testing of silent, Diesel engine driven factory assemble, generating set of capacity 125 KVA, 3 phase, 4 wire, 50 Hz, 1500 RPM complete with Engine and alternator mounted on a common MS fabricated base frame with AVM pads, Acoustic enclosure, relay panel for automatic starting on mains failure safety control and metering equipment mounted on & including common base frame and installed on PCC/RCC foundation as recommended by manufacturer and approved by GE and suitable for ambient conditions at Pune, environmental eco-friendly as per CPCB IV+ norms including the following all as specified and directed. Note: PCC foundation work as per manufacture instructions, anti-vibration pads and other standard accessories and comprising of the following complete all as specified and directed

Diesel Engine: Multi Cylinders , Inline arrangement, Gross Engine power (HP) 154 and (KWm) 116, water cooled turbocharged with after cooled, rated output 1500 RPM and overspeed trip 1650 RPM, Engine Is with electric start, compression ignition, stroke cycle designed to run continuously at 1500 RPM conforming to IS 2002, ISO-3046, BS 5514 standards. Diesel engines should comply with CPCB IV+ norms. The Diesel Engine are comprising of followings: (1) Radiator with Fan (2) Fuel Injection equipment with Electronic Governor having CRS (Common Rail system) and DG performance class G3 (3) Dry type air cleaner (4) Exhaust silencer type NA, Max allowable backpressure (kPa) 17, Exhaust temperature (Deg C) 550, (5) Lub oil filter (Spin on type), (6) Fuel oil filter (Spin on type), (7) 24V electric starting system, (8) Battery charging alternator, (9) Stop Solenoid, (10) Lube Oil pressure Gauge, (11) Water Temperature Gauge, (12) lube oil temperature Gauge, (13) Battery voltage, (14) Extended life coolant, (15) First fill lube Oil

Alternator: Alternator type 4P, rotating field, automatic voltage regulator and voltage regulation +/- 1%, suitable for continuous duty operations rated at 1500 RPM, 415V, 0.8PF, 50 Hz, current (3Ph) Amps-174 in SPDP enclosure, Self-Excited & Self-regulated, Brushless, ‘H’ class insulation, temperature rise (Deg C) 125, coupling type Fle Disc, unbalanced load capability 25% of rated amps, Floor mounted with anti-friction Sealed ball bearing on end. Alternator charging 12V DC/35A, the alternator conforms to IS: 13364 (Part-II) suitable for tropical condition including making cable connection.

Acoustic Enclosure: (a) Specially designed to meet stringent MoEF / CPCB norms of 75 dBA @ 1 Mtr at 75% Load under free field conditions. (b) The followings are some technical features of Acoustic Enclosure: (1) The Enclosure is modular in construction. (2) Base Frame is made of Sheet metal. (3) Durable industrial locking system is provided on Doors. (4) Door Gaskets are made in high quality EPDM material. (c) Corrosion Resistance: To make the Enclosure weather proof:- (1) All sheet metal parts/components are hot dipped in seven tanks process, Pretreated and Passivated (2) Sheet metal components are with Pretreated and Passivated Base Powder Coated. (3) Base Frame is Epoxy Coated/Powder Coated. (4) Zinc Passivated Hardwares are used to avoid rusting. acoustic insulation: (1) Sound proofing of the Enclosure is done with Quality Rockwool confirming to IS:8183 Standard. (2) Acoustic foam shall be fire retardant and fire resistant. (3) Attenuates are provided to control sound at entry and exit of container. (4) Specially designed Residential Silencer is provided. (d) Ventilation And Air Circulation: Exhaust pipe inside Enclosure is thoroughly insulated by Cladding of Rock wool and Sheet.

(e) ELECTRICAL: Neutral Body Earthing points at the sides of enclosure are isolated through Moulded compound. (f) SAFETIES: Emergency Push button to Stop the DG set from outside, Low Fuel oil level, Low Lube oil pressure, Low Coolant Level, High Engine Temperature. The canopies being offered are for output of Noise Level ≤ 75 dbA at a distance of 1-meter average, as per the CPCB IV+ Norms. Batteries: 2 Nos. 12V 90Ah batteries with leads for electric starting. Paint: DG set and panel package will be painted with powder coated type paint. STANDARD GENSET CONTROLLER UNIT WITH CONTROL PANEL: - Genset Controller unit with totally enclosed, Steel Construction Control Panel suitable for indoor floor /wall mounting installation having standard safeties and display parameters.”

AMF PANEL: Supply, install, testing and commissioning of AMF Panel for 125 KVA DG Set factory made, outdoor cubical type as per IE/CPRI rules with IP-54 protection, dust and vermin proof, compartmentalised, made of 3.15 mm thick CRCA sheet, fixed on MS angle iron frame of 50 x 50 x 6 mm thick of required type for supporting double door both sides open type with necessary locking arrangement with slope roof on top duly painted with two coats of powder coated sense grey paint with seven tank process complete and having separate doors inside for accommodating all incoming/outgoing cables and other relevant standards mounted on and including provision of necessary plinth in PCC 1:3:6, type C1 for foundation and PCC pillars with suitable size of nut, bolts & washers grouted as required at site and as per manufacturer's instructions including provision of the following items complete all as specified and directed. (a) Bus bar with electrolytic copper bus bar (for Mains and DG supply incoming and outgoing) suitable for 300 amps capacity for 3 phase and neutral(TPN) (all connection inside the panel shall be through aluminium strip) connected duly supported with FRP insulators including colour code heat shrink insulating sleeves (b) Three phase 4 Pole, Power contractor, 200 Amps for ON-OFF the DG and mains supply -02 Nos (c) MCCB 200 Amps, 36KA for ON-OFF the DG and mains supply -02 Nos (d) MCCB 200 Amps, 36KA - 02 Nos.

Supply, installation, commissioning & testing of silent, Diesel engine driven factory assemble, generating set of capacity 160 KVA, 3 phase, 4 wire, 50 Hz, 1500 RPM complete with Engine and alternator mounted on a common MS fabricated base frame with AVM pads, Acoustic enclosure, relay panel for automatic starting on mains failure safety control and metering equipment mounted on & including common base frame and installed on PCC/RCC foundation as recommended by manufacturer and approved by GE and suitable for ambient conditions at Pune, environmental eco-friendly as per CPCB IV+ norms including the following all as specified and directed. Note: PCC foundation work as per manufacture instructions, anti-vibration pads and other standard accessories and comprising of the following complete all as specified and directed

Diesel Engine: Multi Cylinders , Inline arrangement, Gross Engine power (HP) 197 and (KWm) 147, water cooled turbocharged with after cooled, rated output 1500 RPM and overspeed trip 1650 RPM, Engine Is with electric start, compression ignition, stroke cycle designed to run continuously at 1500 RPM conforming to IS 2002, ISO-3046, BS 5514 standards. Diesel engines should comply with CPCB IV+ norms. The Diesel Engine are comprising of followings: (1) Radiator with Fan (2) Fuel Injection equipment with Electronic Governor having CRS (Common Rail system) and DG performance class G3 (3) Dry type air cleaner (4) Exhaust silencer type NA, Max allowable backpressure (kPa) 17, Exhaust temperature (Deg C) 550, (5) Lub oil filter (Spin on type), (6) Fuel oil filter (Spin on type), (7) 24V electric starting system, (8) Battery charging alternator, (9) Stop Solenoid, (10) Lube Oil pressure Gauge, (11) Water Temperature Gauge, (12) lube oil temperature Gauge, (13) Battery voltage, (14) Extended life coolant, (15) First fill lube Oil

Alternator: Alternator type 4P, rotating field, automatic voltage regulator and voltage regulation +/- 1%, suitable for continuous duty operations rated at 1500 RPM, 415V, 0.8PF, 50 Hz, current (3Ph) Amps-223 in SPDP enclosure, Self-Excited & Self-regulated, Brushless, ‘H’ class insulation, temperature rise (Deg C) 125, coupling type Fle Disc, unbalanced load capability 25% of rated amps, Floor mounted with anti-friction Sealed ball bearing on end. Alternator charging 12V DC/35A, the alternator conforms to IS: 13364 (Part-II) suitable for tropical condition including making cable connection.

Acoustic Enclosure: (a) Specially designed to meet stringent MoEF / CPCB norms of 75 dBA @ 1 Mtr at 75% Load under free field conditions. (b) The followings are some technical features of Acoustic Enclosure: (1) The Enclosure is modular in construction. (2) Base Frame is made of Sheet metal. (3) Durable industrial locking system is provided on Doors. (4) Door Gaskets are made in high quality EPDM material. (c) Corrosion Resistance: To make the Enclosure weather proof:- (1) All sheet metal parts/components are hot dipped in seven tanks process, Pretreated and Passivated (2) Sheet metal components are with Pretreated and Passivated Base Powder Coated. (3) Base Frame is Epoxy Coated/Powder Coated. (4) Zinc Passivated Hardwares are used to avoid rusting. acoustic insulation: (1) Sound proofing of the Enclosure is done with Quality Rockwool confirming to IS:8183 Standard. (2) Acoustic foam shall be fire retardant and fire resistant. (3) Attenuates are provided to control sound at entry and exit of container. (4) Specially designed Residential Silencer is provided. (d) Ventilation And Air Circulation: Exhaust pipe inside Enclosure is thoroughly insulated by Cladding of Rock wool and Sheet.

(e) ELECTRICAL: Neutral Body Earthing points at the sides of enclosure are isolated through Moulded compound. (f) SAFETIES: Emergency Push button to Stop the DG set from outside, Low Fuel oil level, Low Lube oil pressure, Low Coolant Level, High Engine Temperature. The canopies being offered are for output of Noise Level ≤ 75 dbA at a distance of 1-meter average, as per the CPCB IV+ Norms. Batteries: 2 Nos. 12V 110Ah batteries with leads for electric starting. Paint: DG set and panel package will be painted with powder coated type paint. STANDARD GENSET CONTROLLER UNIT WITH CONTROL PANEL: - Genset Controller unit with totally enclosed, Steel Construction Control Panel suitable for indoor floor /wall mounting installation having standard safeties and display parameters.”

AMF PANEL: Supply, install, testing and commissioning of AMF Panel for 160 KVA DG Set factory made, outdoor cubical type as per IE/CPRI rules with IP-54 protection, dust and vermin proof, compartmentalised, made of 3.15 mm thick CRCA sheet, fixed on MS angle iron frame of 50 x 50 x 6 mm thick of required type for supporting double door both sides open type with necessary locking arrangement with slope roof on top duly painted with two coats of powder coated sense grey paint with seven tank process complete and having separate doors inside for accommodating all incoming/outgoing cables and other relevant standards mounted on and including provision of necessary plinth in PCC 1:3:6, type C1 for foundation and PCC pillars with suitable size of nut, bolts & washers grouted as required at site and as per manufacturer's instructions including provision of the following items complete all as specified and directed. (a) Bus bar with electrolytic copper bus bar (for Mains and DG supply incoming and outgoing) suitable for 400 amps capacity for 3 phase and neutral(TPN) (all connection inside the panel shall be through aluminium strip) connected duly supported with FRP insulators including colour code heat shrink insulating sleeves (b) Three phase 4 Pole, Power contractor, 250 Amps for ON-OFF the DG and mains supply -02 Nos (c) MCCB 250 Amps, 36KA for ON-OFF the DG and mains supply -02 Nos (d) MCCB 250 Amps, 36KA - 02 Nos.

Supply, installation, commissioning & testing of silent, Diesel engine driven factory assemble, generating set of capacity 200 KVA, 3 phase, 4 wire, 50 Hz, 1500 RPM complete with Engine and alternator mounted on a common MS fabricated base frame with AVM pads, Acoustic enclosure, relay panel for automatic starting on mains failure safety control and metering equipment mounted on & including common base frame and installed on PCC/RCC foundation as recommended by manufacturer and approved by GE and suitable for ambient conditions at Pune, environmental eco-friendly as per CPCB IV+ norms including the following all as specified and directed. Note: PCC foundation work as per manufacture instructions, anti-vibration pads and other standard accessories and comprising of the following complete all as specified and directed

Diesel Engine: Multi Cylinders, Inline arrangement, Gross Engine power (HP) 237 and (KWm) 178, water cooled turbocharged with after cooled, rated output 1500 RPM and overspeed trip 1650 RPM, Engine Is with electric start, compression ignition, stroke cycle designed to run continuously at 1500 RPM conforming to IS 2002, ISO-3046, BS 5514 standards. Diesel engines should comply with CPCB IV+ norms. The Diesel Engine are comprising of followings: (1) Radiator with Fan (2) Fuel Injection equipment with Electronic Governor having CRS (Common Rail system) and DG performance class G3 (3) Dry type air cleaner (4) Exhaust silencer type NA, Max allowable backpressure (kPa) 17, Exhaust temperature (Deg C) 550, (5) Lub oil filter (Spin on type), (6) Fuel oil filter (Spin on type), (7) 24V electric starting system, (8) Battery charging alternator, (9) Stop Solenoid, (10) Lube Oil pressure Gauge, (11) Water Temperature Gauge, (12) lube oil temperature Gauge, (13) Battery voltage, (14) Extended life coolant, (15) First fill lube Oil

Alternator: Alternator type 4P, rotating field, automatic voltage regulator and voltage regulation +/- 1%, suitable for continuous duty operations rated at 1500 RPM, 415V, 0.8PF, 50 Hz, current (3Ph) Amps-278 in SPDP enclosure, Self-Excited & Self-regulated, Brushless, ‘H’ class insulation, temperature rise (Deg C) 125, coupling type Fle Disc, unbalanced load capability 25% of rated amps, Floor mounted with anti-friction Sealed ball bearing on end. Alternator charging 12V DC/35A, the alternator conforms to IS: 13364 (Part-II) suitable for tropical condition including making cable connection.

Acoustic Enclosure: (a) Specially designed to meet stringent MoEF / CPCB norms of 75 dBA @ 1 Mtr at 75% Load under free field conditions. (b) The followings are some technical features of Acoustic Enclosure: (1) The Enclosure is modular in construction. (2) Base Frame is made of Sheet metal. (3) Durable industrial locking system is provided on Doors. (4) Door Gaskets are made in high quality EPDM material. (c) Corrosion Resistance: To make the Enclosure weather proof:- (1) All sheet metal parts/components are hot dipped in seven tanks process, Pretreated and Passivated (2) Sheet metal components are with Pretreated and Passivated Base Powder Coated. (3) Base Frame is Epoxy Coated/Powder Coated. (4) Zinc Passivated Hardwares are used to avoid rusting. acoustic insulation: (1) Sound proofing of the Enclosure is done with Quality Rockwool confirming to IS:8183 Standard. (2) Acoustic foam shall be fire retardant and fire resistant. (3) Attenuates are provided to control sound at entry and exit of container. (4) Specially designed Residential Silencer is provided. (d) Ventilation And Air Circulation: Exhaust pipe inside Enclosure is thoroughly insulated by Cladding of Rock wool and Sheet.

(e) ELECTRICAL: Neutral Body Earthing points at the sides of enclosure are isolated through Moulded compound. (f) SAFETIES: Emergency Push button to Stop the DG set from outside, Low Fuel oil level, Low Lube oil pressure, Low Coolant Level, High Engine Temperature. The canopies being offered are for output of Noise Level ≤ 75 dbA at a distance of 1-meter average, as per the CPCB IV+ Norms. Batteries: 2 Nos. 12V 150Ah batteries with leads for electric starting. Paint: DG set and panel package will be painted with powder coated type paint. STANDARD GENSET CONTROLLER UNIT WITH CONTROL PANEL: - Genset Controller unit with totally enclosed, Steel Construction Control Panel suitable for indoor floor /wall mounting installation having standard safeties and display parameters.”

AMF PANEL: Supply, install, testing and commissioning of AMF Panel for 200 KVA DG Set factory made, outdoor cubical type as per IE/CPRI rules with IP-54 protection, dust and vermin proof, compartmentalised, made of 3.15 mm thick CRCA sheet, fixed on MS angle iron frame of 50 x 50 x 6 mm thick of required type for supporting double door both sides open type with necessary locking arrangement with slope roof on top duly painted with two coats of powder coated sense grey paint with seven tank process complete and having separate doors inside for accommodating all incoming/outgoing cables and other relevant standards mounted on and including provision of necessary plinth in PCC 1:3:6, type C1 for foundation and PCC pillars with suitable size of nut, bolts & washers grouted as required at site and as per manufacturer's instructions including provision of the following items complete all as specified and directed. (a) Bus bar with electrolytic copper bus bar (for Mains and DG supply incoming and outgoing) suitable for 450 amps capacity for 3 phase and neutral(TPN) (all connection inside the panel shall be through aluminium strip) connected duly supported with FRP insulators including colour code heat shrink insulating sleeves (b) Three phase 4 Pole, Power contractor, 315 Amps for ON-OFF the DG and mains supply -02 Nos (c) MCCB 315 Amps, 36KA for ON-OFF the DG and mains supply -02 Nos (d) MCCB 315 Amps, 36KA - 02 Nos.

Supply, installation, commissioning & testing of silent, Diesel engine driven factory assemble, generating set of capacity 250 KVA, 3 phase, 4 wire, 50 Hz, 1500 RPM complete with Engine and alternator mounted on a common MS fabricated base frame with AVM pads, Acoustic enclosure, relay panel for automatic starting on mains failure safety control and metering equipment mounted on & including common base frame and installed on PCC/RCC foundation as recommended by manufacturer and approved by GE and suitable for ambient conditions at Pune, environmental eco-friendly as per CPCB IV+ norms including the following all as specified and directed. Note: PCC foundation work as per manufacture instructions, anti-vibration pads and other standard accessories and comprising of the following complete all as specified and directed

Diesel Engine: Multi Cylinders, Inline arrangement, Gross Engine power (HP) 303 and (KWm) 223, water cooled turbocharged with after cooled, rated output 1500 RPM and overspeed trip 1650 RPM, Engine Is with electric start, compression ignition, stroke cycle designed to run continuously at 1500 RPM conforming to IS 2002, ISO-3046, BS 5514 standards. Diesel engines should comply with CPCB IV+ norms. The Diesel Engine are comprising of followings: (1) Radiator with Fan (2) Fuel Injection equipment with Electronic Governor having CRS (Common Rail system) and DG performance class G3 (3) Dry type air cleaner (4) Exhaust silencer type NA, Max allowable backpressure (kPa) 17, Exhaust temperature (Deg C) 550, (5) Lub oil filter (Spin on type), (6) Fuel oil filter (Spin on type), (7) 24V electric starting system, (8) Battery charging alternator, (9) Stop Solenoid, (10) Lube Oil pressure Gauge, (11) Water Temperature Gauge, (12) lube oil temperature Gauge, (13) Battery voltage, (14) Extended life coolant, (15) First fill lube Oil

Alternator: Alternator type 4P, rotating field, automatic voltage regulator and voltage regulation +/- 1%, suitable for continuous duty operations rated at 1500 RPM, 415V, 0.8PF, 50 Hz, current (3Ph) Amps-346 in SPDP enclosure, Self-Excited & Self-regulated, Brushless, ‘H’ class insulation, temperature rise (Deg C) 125, coupling type Fle Disc, unbalanced load capability 25% of rated amps, Floor mounted with anti-friction Sealed ball bearing on end. Alternator charging 12V DC/35A, the alternator conforms to IS: 13364 (Part-II) suitable for tropical condition including making cable connection.

Acoustic Enclosure: (a) Specially designed to meet stringent MoEF / CPCB norms of 75 dBA @ 1 Mtr at 75% Load under free field conditions. (b) The followings are some technical features of Acoustic Enclosure: (1) The Enclosure is modular in construction. (2) Base Frame is made of Sheet metal. (3) Durable industrial locking system is provided on Doors. (4) Door Gaskets are made in high quality EPDM material. (c) Corrosion Resistance: To make the Enclosure weather proof:- (1) All sheet metal parts/components are hot dipped in seven tanks process, Pretreated and Passivated (2) Sheet metal components are with Pretreated and Passivated Base Powder Coated. (3) Base Frame is Epoxy Coated/Powder Coated. (4) Zinc Passivated Hardwares are used to avoid rusting. acoustic insulation: (1) Sound proofing of the Enclosure is done with Quality Rockwool confirming to IS:8183 Standard. (2) Acoustic foam shall be fire retardant and fire resistant. (3) Attenuates are provided to control sound at entry and exit of container. (4) Specially designed Residential Silencer is provided. (d) Ventilation And Air Circulation: Exhaust pipe inside Enclosure is thoroughly insulated by Cladding of Rock wool and Sheet.

(e) ELECTRICAL: Neutral Body Earthing points at the sides of enclosure are isolated through Moulded compound. (f) SAFETIES: Emergency Push button to Stop the DG set from outside, Low Fuel oil level, Low Lube oil pressure, Low Coolant Level, High Engine Temperature. The canopies being offered are for output of Noise Level ≤ 75 dbA at a distance of 1-meter average, as per the CPCB IV+ Norms. Batteries: 2 Nos. 12V 180Ah batteries with leads for electric starting. Paint: DG set and panel package will be painted with powder coated type paint. STANDARD GENSET CONTROLLER UNIT WITH CONTROL PANEL: - Genset Controller unit with totally enclosed, Steel Construction Control Panel suitable for indoor floor /wall mounting installation having standard safeties and display parameters.”

AMF PANEL: Supply, install, testing and commissioning of AMF Panel for 250 KVA DG Set factory made, outdoor cubical type as per IE/CPRI rules with IP-54 protection, dust and vermin proof, compartmentalised, made of 3.15 mm thick CRCA sheet, fixed on MS angle iron frame of 50 x 50 x 6 mm thick of required type for supporting double door both sides open type with necessary locking arrangement with slope roof on top duly painted with two coats of powder coated sense grey paint with seven tank process complete and having separate doors inside for accommodating all incoming/outgoing cables and other relevant standards mounted on and including provision of necessary plinth in PCC 1:3:6, type C1 for foundation and PCC pillars with suitable size of nut, bolts & washers grouted as required at site and as per manufacturer's instructions including provision of the following items complete all as specified and directed. (a) Bus bar with electrolytic copper bus bar (for Mains and DG supply incoming and outgoing) suitable for 600 amps capacity for 3 phase and neutral(TPN) (all connection inside the panel shall be through aluminium strip) connected duly supported with FRP insulators including colour code heat shrink insulating sleeves (b) Three phase 4 Pole, Power contractor, 400 Amps for ON-OFF the DG and mains supply -02 Nos (c) MCCB 400 Amps, 36KA for ON-OFF the DG and mains supply -02 Nos (d) MCCB 400 Amps, 36KA - 02 Nos.

Supply, installation, commissioning & testing of silent, Diesel engine driven factory assemble, generating set of capacity 400 KVA, 3 phase, 4 wire, 50 Hz, 1500 RPM complete with Engine and alternator mounted on a common MS fabricated base frame with AVM pads, Acoustic enclosure, relay panel for automatic starting on mains failure safety control and metering equipment mounted on & including common base frame and installed on PCC/RCC foundation as recommended by manufacturer and approved by GE and suitable for ambient conditions at Pune, environmental eco-friendly as per CPCB IV+ norms including the following all as specified and directed. Note: PCC foundation work as per manufacture instructions, anti-vibration pads and other standard accessories and comprising of the following complete all as specified and directed

Diesel Engine: Multi Cylinders , Inline arrangement, Gross Engine power (HP) 594 and (KWm) 320, water cooled turbocharged with after cooled, rated output 1500 RPM and overspeed trip 1650 RPM, Engine Is with electric start, compression ignition, stroke cycle designed to run continuously at 1500 RPM conforming to IS 2002, ISO-3046, BS 5514 standards. Diesel engines should comply with CPCB IV+ norms. The Diesel Engine are comprising of followings: (1) Radiator with Fan (2) Fuel Injection equipment with Electronic Governor having CRS (Common Rail system) and DG performance class G3 (3) Dry type air cleaner (4) Exhaust silencer type NA, Max allowable backpressure (kPa) 17, Exhaust temperature (Deg C) 550, (5) Lub oil filter (Spin on type), (6) Fuel oil filter (Spin on type), (7) 24V electric starting system, (8) Battery charging alternator, (9) Stop Solenoid, (10) Lube Oil pressure Gauge, (11) Water Temperature Gauge, (12) lube oil temperature Gauge, (13) Battery voltage, (14) Extended life coolant, (15) First fill lube Oil

Alternator: Alternator type 4P, rotating field, automatic voltage regulator and voltage regulation +/- 1%, suitable for continuous duty operations rated at 1500 RPM, 415V, 0.8PF, 50 Hz, current (3Ph) Amps-556 in SPDP enclosure, Self-Excited & Self-regulated, Brushless, ‘H’ class insulation, temperature rise (Deg C) 125, coupling type Fle Disc, unbalanced load capability 25% of rated amps, Floor mounted with anti-friction Sealed ball bearing on end. Alternator charging 12V DC/35A, the alternator conforms to IS: 13364 (Part-II) suitable for tropical condition including making cable connection.

Acoustic Enclosure: (a) Specially designed to meet stringent MoEF / CPCB norms of 75 dBA @ 1 Mtr at 75% Load under free field conditions. (b) The followings are some technical features of Acoustic Enclosure: (1) The Enclosure is modular in construction. (2) Base Frame is made of Sheet metal. (3) Durable industrial locking system is provided on Doors. (4) Door Gaskets are made in high quality EPDM material. (c) Corrosion Resistance: To make the Enclosure weather proof:- (1) All sheet metal parts/components are hot dipped in seven tanks process, Pretreated and Passivated (2) Sheet metal components are with Pretreated and Passivated Base Powder Coated. (3) Base Frame is Epoxy Coated/Powder Coated. (4) Zinc Passivated Hardwares are used to avoid rusting. acoustic insulation: (1) Sound proofing of the Enclosure is done with Quality Rockwool confirming to IS:8183 Standard. (2) Acoustic foam shall be fire retardant and fire resistant. (3) Attenuates are provided to control sound at entry and exit of container. (4) Specially designed Residential Silencer is provided. (d) Ventilation And Air Circulation: Exhaust pipe inside Enclosure is thoroughly insulated by Cladding of Rock wool and Sheet.

(e) ELECTRICAL: Neutral Body Earthing points at the sides of enclosure are isolated through Moulded compound. (f) SAFETIES: Emergency Push button to Stop the DG set from outside, Low Fuel oil level, Low Lube oil pressure, Low Coolant Level, High Engine Temperature. The canopies being offered are for output of Noise Level ≤ 75 dbA at a distance of 1-meter average, as per the CPCB IV+ Norms. Batteries: 2 Nos. 12V 180Ah batteries with leads for electric starting. Paint: DG set and panel package will be painted with powder coated type paint. STANDARD GENSET CONTROLLER UNIT WITH CONTROL PANEL: - Genset Controller unit with totally enclosed, Steel Construction Control Panel suitable for floor /wall mounting installation having standard safeties and display parameters.”

AMF PANEL: Supply, install, testing and commissioning of AMF Panel for 400 KVA DG Set factory made, outdoor cubical type as per IE/CPRI rules with IP-54 protection, dust and vermin proof, compartmentalised, made of 3.15 mm thick CRCA sheet, fixed on MS angle iron frame of 50 x 50 x 6 mm thick of required type for supporting double door both sides open type with necessary locking arrangement with slope roof on top duly painted with two coats of powder coated sense grey paint with seven tank process complete and having separate doors inside for accommodating all incoming/outgoing cables and other relevant standards mounted on and including provision of necessary plinth in PCC 1:3:6, type C1 for foundation and PCC pillars with suitable size of nut, bolts & washers grouted as required at site and as per manufacturer's instructions including provision of the following items complete all as specified and directed. (a) Bus bar with electrolytic copper bus bar (for Mains and DG supply incoming and outgoing) suitable for 1000 amps capacity for 3 phase and neutral(TPN) (all connection inside the panel shall be through aluminium strip) connected duly supported with FRP insulators including colour code heat shrink insulating sleeves (b) Three phase 4 Pole, Power contractor, 600 Amps for ON-OFF the DG and mains supply -02 Nos (c) MCCB 630 Amps, 36KA for ON-OFF the DG and mains supply -02 Nos (d) MCCB 630 Amps, 36KA - 02 Nos.

Supply, installation, commissioning & testing of silent, Diesel engine driven factory assemble, generating set of capacity 500 KVA, 3 phase, 4 wire, 50 Hz, 1500 RPM complete with Engine and alternator mounted on a common MS fabricated base frame with AVM pads, Acoustic enclosure, relay panel for automatic starting on mains failure safety control and metering equipment mounted on & including common base frame and installed on PCC/RCC foundation as recommended by manufacturer and approved by GE and suitable for ambient conditions at Pune, environmental eco-friendly as per CPCB IV+ norms including the following all as specified and directed. Note: PCC foundation work as per manufacture instructions, anti-vibration pads and other standard accessories and comprising of the following complete all as specified and directed

Diesel Engine: Multi Cylinders , Inline arrangement, Gross Engine power (HP) 594 and (KWm) 400, water cooled turbocharged with after cooled, rated output 1500 RPM and overspeed trip 1650 RPM, Engine Is with electric start, compression ignition, stroke cycle designed to run continuously at 1500 RPM conforming to IS 2002, ISO-3046, BS 5514 standards. Diesel engines should comply with CPCB IV+ norms. The Diesel Engine are comprising of followings: (1) Radiator with Fan (2) Fuel Injection equipment with Electronic Governor having CRS (Common Rail system) and DG performance class G3 (3) Dry type air cleaner (4) Exhaust silencer type NA, Max allowable backpressure (kPa) 17, Exhaust temperature (Deg C) 550, (5) Lub oil filter (Spin on type), (6) Fuel oil filter (Spin on type), (7) 24V electric starting system, (8) Battery charging alternator, (9) Stop Solenoid, (10) Lube Oil pressure Gauge, (11) Water Temperature Gauge, (12) lube oil temperature Gauge, (13) Battery voltage, (14) Extended life coolant, (15) First fill lube Oil

Alternator: Alternator type 4P, rotating field, automatic voltage regulator and voltage regulation +/- 1%, suitable for continuous duty operations rated at 1500 RPM, 415V, 0.8PF, 50 Hz, current (3Ph) Amps-695 in SPDP enclosure, Self-Excited & Self-regulated, Brushless, ‘H’ class insulation, temperature rise (Deg C) 125, coupling type Fle Disc, unbalanced load capability 25% of rated amps, Floor mounted with anti-friction Sealed ball bearing on end. Alternator charging 12V DC/35A, the alternator conforms to IS: 13364 (Part-II) suitable for tropical condition including making cable connection.

Acoustic Enclosure: (a) Specially designed to meet stringent MoEF / CPCB norms of 75 dBA @ 1 Mtr at 75% Load under free field conditions. (b) The followings are some technical features of Acoustic Enclosure: (1) The Enclosure is modular in construction. (2) Base Frame is made of Sheet metal. (3) Durable industrial locking system is provided on Doors. (4) Door Gaskets are made in high quality EPDM material. (c) Corrosion Resistance: To make the Enclosure weather proof:- (1) All sheet metal parts/components are hot dipped in seven tanks process, Pretreated and Passivated (2) Sheet metal components are with Pretreated and Passivated Base Powder Coated. (3) Base Frame is Epoxy Coated/Powder Coated. (4) Zinc Passivated Hardwares are used to avoid rusting. acoustic insulation: (1) Sound proofing of the Enclosure is done with Quality Rockwool confirming to IS:8183 Standard. (2) Acoustic foam shall be fire retardant and fire resistant. (3) Attenuates are provided to control sound at entry and exit of container. (4) Specially designed Residential Silencer is provided. (d) Ventilation And Air Circulation: Exhaust pipe inside Enclosure is thoroughly insulated by Cladding of Rock wool and Sheet.

(e) ELECTRICAL: Neutral Body Earthing points at the sides of enclosure are isolated through Moulded compound. (f) SAFETIES: Emergency Push button to Stop the DG set from outside, Low Fuel oil level, Low Lube oil pressure, Low Coolant Level, High Engine Temperature. The canopies being offered are for output of Noise Level ≤ 75 dbA at a distance of 1-meter average, as per the CPCB IV+ Norms. Batteries: 2 Nos. 12V 180Ah batteries with leads for electric starting. Paint: DG set and panel package will be painted with powder coated type paint. STANDARD GENSET CONTROLLER UNIT WITH CONTROL PANEL: - Genset Controller unit with totally enclosed, Steel Construction Control Panel suitable for floor / wall mounting installation having standard safeties anddi splay parameters.”

AMF PANEL: Supply, install, testing and commissioning of AMF Panel for 500 KVA DG Set factory made, outdoor cubical type as per IE/CPRI rules with IP-54 protection, dust and vermin proof, compartmentalised, made of 3.15 mm thick CRCA sheet, fixed on MS angle iron frame of 50 x 50 x 6 mm thick of required type for supporting double door both sides open type with necessary locking arrangement with slope roof on top duly painted with two coats of powder coated sense grey paint with seven tank process complete and having separate doors inside for accommodating all incoming/outgoing cables and other relevant standards mounted on and including provision of necessary plinth in PCC 1:3:6, type C1 for foundation and PCC pillars with suitable size of nut, bolts & washers grouted as required at site and as per manufacturer's instructions including provision of the following items complete all as specified and directed. (a) Bus bar with electrolytic copper bus bar (for Mains and DG supply incoming and outgoing) suitable for 1200 amps capacity for 3 phase and neutral(TPN) (all connection inside the panel shall be through aluminium strip) connected duly supported with FRP insulators including colour code heat shrink insulating sleeves (b) Three phase 4 Pole, Power contractor, 800 Amps for ON-OFF the DG and mains supply -02 Nos (c) MCCB 800 Amps, 65KA for ON-OFF the DG and mains supply -02 Nos (d) MCCB 800 Amps, 65KA - 02 Nos.

Supply and fixing sheet steel enclosure duly powder coated with thermal magnetic, release MCCB 4 Pole 250 Amps , 36 KA, Suitable for 440 Volts, 3 Phase 4 wire 50Hz AC supply system, wall mounteed type including drilling holes to wall, making connections, etc as required.

Supply, Install, testing and commissioning, factory made and tested, CPRI approved LT panel board outdoor type, hood on top weather, vermin proof, free standing floor mounting type mounted on floor, cable alley for all the feeders, suitable for 440Volts, 3 Phase 4wire 50Hz AC supply system, conforming to IS, IP-64 class protection and made of 3.15 mm CRCA mild steel sheet with 50x50x6mm angle iron frame, hinged doors, front & rear opening and locking arrangement and duly powder coated on the outside and inside including necessary earthwork excavation and provision of two Nos earth terminals on both sides , including cable gland and lugs for incoming and outgoing cable etc. and PCC foundation with PCC 1 : 2 : 4, type B1, using 20mm graded crushed stone aggregate, of suitable size to accommodate with and including comprising of the the following: INCOMING: (a) Bus bar chamber with electrolytic aluminium bus bar suitable for 400 amps capacity for 3 phase and neutral (all connection inside the panel shall be through aluminium strip) connected duly supported with FRP insulators including colour code heat shrinked insulating sleeves (b) MCCB 4 pole adjustable thermal/magnetic setting, 200 Amp, 415 Volts 36 kA – 01 No as incomer, OUTGOING: (a) MCCB 3 pole adjustable thermal/magnetic setting, 150 Amp, 415 Volts 16 KA – 02 Nos. (b) LED Indicator lamp 22.5 mm dia RYB, 230 volts - 01 Set of 03 Nos. (g) Panel control wiring with suitable size PVC insulated heavy duty 1100 volts grade single core cable with copper conductor multistranded with cable end terminaion lugs. (h) Digital volt meter and ammeter wtih CTs complete all as specified and directed.

M&L for earthing complete with galvanised steel, earth plate electrode 600x600mm x 6mm thick burried directly in ground verticaly (earth pit not less than 2.25 mtrs below ground level ) with top edge of the plate not less than 1.5 mtrs below normal ground level connected to galvanised iron 25 x 4 mm strip as earth lead by means of bolts, nuts, check nuts and washers of galvanised iron/steel all as shown in electrical plate No 3 on page 497 of MES schedule 2009 part - I connected to main switch board/main DBs/earthing test point including all necessary excavation and earth work in hard/dense soil common salt and charcoal dust mixed and packed in layers each 150mm thick all round the GI earth plate, watering pipe 20mm dia GI medium grade. GI sheet 0.63 mm thick funnel, wire gauge, pit/chamber in PCC 1:3:6 type C1 and 50mm thick RCC cover in PCC 1:2:4 type B1 duly reinforced with MS round bars 6mm dia @ 150c/c both ways with suitable lifting handle to cover, GI protection pipe 40mm dia light grade up to 7.5mtr from electrode GI pipe to be fixed with complete all as specified and directed.

Providing and fixing 25 mm X 4 mm GI strip in 40 mm dia G.I. pipe from earth electrode including connection with brass nut, bolt, spring, washer excavation and re-filling etc. as required. (for LT panel) all as specified and directed

Earth work in surface excavation in all kinds of soil, not exceeding 30 cm in depth but exceeding 1.5 m in width as well as 10 sqm on plan including getting out and disposal of excavated earth upto 50 m and lift upto 1.5 m, as directed by Engineer-in- Charge:

Earth work in excavation over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) in All kinds of soil by mechanical means (Hydraulic excavator)/ manual means including getting out and disposal of excavated earth lead upto 50 m and lift upto 1.5 m, as directed by Engineer-incharge.

Providing and laying in position cement concrete of 1:4:8 (1 Cement : 4 coarse sand (zone-III) : 8 graded stone aggregate 40 mm nominal size) grade for all work up to plinth level all as specified and directed but excluding the cost of centering and shuttering -

Providing and laying in position cement concrete of 1:2:4 (1 cement : 2 coarse sand (zone-III) derived from natural sources : 4 graded stone aggregate 20 mm nominal size derived from natural sources) grade for All works up to plinth level all as specified and directed but excluding the cost of centering and shuttering -

Providing and laying in position cement concrete of 1:2:4 (1 cement : 2 coarse sand (zone-III) derived from natural sources : 4 graded stone aggregate 20 mm nominal size derived from natural sources) grade for All works above plinth level all as specified and directed but excluding the cost of centering and shuttering -

Centering and shuttering including strutting, propping etc. and removal of form work for Foundations, footings, bases for columns all as specified and directed.

Centering and shuttering including strutting, propping etc. and removal of form work for Retaining walls, return walls, walls (any thickness) including attached pilasters, buttresses, plinth and string courses fillets,kerbs and steps etc.all as specified and directed.

Providing and laying in position ready mixed or site batched design mix cement concreteof M20 grade with minimum cement content of 270 kg /cum for plain cement concrete work & all works upto plinth level Concrete ; using coarse aggregate and fine aggregate derived from natural sources, Portland Pozzolana/Ordinary Portland /Portland Slag cement, admixtures in recommended proportions as per IS: 9103 to accelerate / retard setting of concrete, to improve durability and workability without impairing strength; including pumping of concrete to site of laying, curing, carriage for all leads; but excluding the cost of centering, shuttering and finishing as per direction of the engineer-in-charge; for the following grades of concrete. Note: In case the cement content in design mix is more than the minimum specified cement content, the contractor shall have discretion to either re-design the mix . The unit rate quoted shall deemed to be included this aspect and bear the cost of extra cement .No claim shall be allowed on this account

Providing and laying in position ready mixed or site batched design mix cement concrete of M20 grade with minimum cement content of 270 kg /cum for plain cement concrete work & All works above plinth and upto floor V level Concrete ; using coarse aggregate and fine aggregate derived from natural sources, Portland Pozzolana/Ordinary Portland /Portland Slag cement, admixtures in recommended proportions as per IS: 9103 to accelerate / retard setting of concrete, to improve durability and workability without impairing strength; including pumping of concrete to site of laying, curing, carriage for all leads; but excluding the cost of centering, shuttering and finishing as per direction of the engineer-in-charge; for the following grades of concrete. Note: In case the cement content in design mix is more than the minimum specified cement content, the contractor shall have discretion to either re-design the mix . The unit rate quoted shall deemed to be included this aspect and bear the cost of extra cement .No claim shall be allowed on this account

Sand filling under floors or in foundations including watering and consolidation complete all as specified and directed.

Material and labour for 150 mm thick back filling with Stone aggregate 40 mm to 63mm nominal size for pitching including consolidation etc. complete all as specified and directed

Cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 40 mm nominal size) in pavements, laid to required slope and camber in panels as required including consolidation finishing and tamping complete all as specified and directed.

Providing and filling in position rubberized bitumen hot sealing compound Using grade 'A' sealing compound conforming to IS: 1834 for sealing of expansion joints in roads / pavements all complete all as specified and directed by the Engineer-in-Charge. .

GEPS PROJECTS (BID ID -3370470)

surendra infrastructure pvt ltd (BID ID -3371227)

TRIVENI CONSTRUCTIONS (BID ID -3371381)

SAGGI ELECTRIC COMPANY (BID ID -3371198)

Shree Ayyappa Engineering (BID ID -3371361)

Sant Construction Co. (BID ID -3371082)

Horizon Construction (BID ID -3371069)

agarwal and company (BID ID -3370533)

K R TRADERS (BID ID -3371432)

V M MATERE INFRASTRUCTURES INDIA PVT LTD (BID ID -3371411)

Hem Construction Company (BID ID -3371273)

Shekhar Enterprises (BID ID -3371599)

SOOD ASSOCIATES PVT LTD (BID ID -3371276)