8577 WELCOME MAINTENANCE TO OFFRS ACCN UNDER AGE BR I OF SOUTH PUNE

Amount

M&L for preparation of old decorative surfaces of wall including cornices (plastered or un-plastered) by brooming down and scrapping wherever necessary and applying one coat of white wash, complete all as specified and directed.

M&L for preparation of old decorative surfaces of wall including, cornices (plastered or unplastered) of any description by using sand paper and remove dust and applying one coat of oil bound distemper of any tint complete all as specified and directed by Engr-in-Charge.

M&L for complete removal of existing finishing from wall surfaces and preparation of wall surfaces including cornices of any description by using sand paper and remove dust etc. and applying two coats of oil bound distemper over and including a coat of 2mm thick wall care putty, complete all as specified and directed

M&L for prepration of newly plastered sureface of walls and applying two coats cement base paint over a coat of alkali resistant primer complete all as specified and as directed.

M&L for applying two coats of synthetic enamel paint over a coat of pink primer on wooden surfaces exc. 10 cm width or girth, including preparation of surfaces, complete al as specified and directed.

M&L for preparation of old painted wooden surfaces exc. 10 cm width or girth and applying one coat of synthetic enamel paint, complete all as specified and directed.

M&L for applying two coats of synthetic enamel paint over a coat of red oxide primer on steel surfaces exc 10 cm width or girth, including preparation of surfaces, complete al as specified and directed.

M&L for preparation of old painted steel surfaces exc. 10 cm width or girth and applying one coat of synthetic enamel paint, complete all as specified and directed.

M & L for preparation of surface of any description (plastered and old decorated) over 10cm width or girth including removing existing treatment completely and applying two coats of Apex Ultima Weather proof exterior emulsion, complete all as specified and directed.

M & L for preparation of surface of any description (plastered and old decorated) over 10cm width or girth and applying one coat of Apex Ultima Weather proof exterior emulsion, complete all as specified and directed., complete all as specified and directed.

M & L for preparation of surface of any description (plastered and old decorated) over 10cm width or girth and applying one coat of luster paint, complete all as specified and directed.

M & L for french ploishing on surfaces of any descrption, exceeding 10 cm width or girth over a coat of wood filler including cleaning and preparation of old wooden surfaces, complete all as specified and directed.

M & L for applying two coats of oil bound distemper on walls over a coat of priming with chalk whitening incuding preparation of new plaster surfaces complete all as specified and directed by Engr-in-Charge.

M&L for three coats white wash on new plastered surfaces of ceilings including preparation of new surfaces, complete as specified and directed.

M&L PCC 1:3:6 type C-2 (Using 40mm graded stone aggregate), 75 mm thick as in plinth protection laid as to bays finished even and smooth without using extra cement including demolition of old existing plinth of any type and removing of debries complete all as specified and as directed

M&L for 25 mm thick PCC 1:2:4 type B-1 (Using 20mm graded stone aggregate) as in floor, finished the surfaces fair & even to receive floor finishes including demolition of old existing PCC layer any type & thickness and removing of debries complete all as specified and as directed

M & L for coloured vitrified ceramic tiles 10 mm thick (square/ rectangular) polished, area of each tiles exceeding 0.16 Sqm but not exceeding 0.36 sqm as in flooring, set and jointed in neat cement slurry & pointed in white or coloured cement to match laid over and including 20mm thick screed bed in CM 1:6 with including taking of old existing unserviceable tiles of any type and removing of debries complete all as specified and as directed

M&L for joint free non-skid ceramic coloured tiles 7 to 8 mm thick area of each tiles exceeding 0.11 Sqm but not exceeding 0.18 as in floors, set an jointed in neat cement slurry and pointed in white or coloured cement to match including laid over and including 20 mm thick screed bed in CM 1:6 including taking down of old existing tiles of any type and removing of debries complete all as specified and as directed

M&L for glazed coloured digital printed ceramic tiles of size 600x300x7mm thick as in vertical surfaces etc set and jointed in neat cement slurry and pointed in coloured cement to match with colour tiles with and including 15 mm thick backing coat in CM 1:4 including triangular filleting in CM 1:4 on top edges including taking down of old existing tiles of any type and removing of debries complete all as specified and as directed

M&L for 20 mm thick Granite slab (of any type/colour) work (table rubbed and polished) in steps, pillars; window cills / jamb, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite as in counters of any radious etc laid over and including 20 mm thick screed bed in CM (1:4) including demolition of existing stone slab of any description and removing of debries complete all as specified and as directed

M & L for machine cut cuddapa stone slabs one side polished, 30 to 40mm thick, set and jointed in neat cement slurry and pointed in coloured cement to match laid over and including 15mm thick screed bed in cement mortar 1:6 including dismantling of old existing stone slabs and removing of debries complete all as specified and as directed

Rounding edges of stone slab one edge, such as in steps, cooking platform and other similar situation complete all as specified and directed.

M&L for brickwork with fly ash bricks, straight or curved on plan exc. 6m mean radius, built in cement mortar 1:6, including dismantling of old existing brick / PCC block wall complete all as specified and as directed

M&Lfor fly ash bricks, straight or curved on plain n. exc. 6m mean radius, built in cement morter 1:4, as in half brick thick walling including dismantling of old existing half brick wall complete all as specified and directed.

M&L for 5 mm thick rendering on fair faces of ceilings in CM 1:3, including finishing the surfaces fair and smooth using sagol finish taking down cement plaster from ceilings etc. and scrubbing down with water complete all as specified and directed.

M&L for rendering 15mm thick on fair faces of brick work in cement mortar 1:6 mixed with integral water proofing compound as per manufacturer’s instructions including finishing of surfaces even and smooth without using extra cement, complete all as specified and directed. Note :- WPC shall be measured & paid separately under respective item

M&L for 15mm thick rendering on fair faces of brick work in CM 1:4 mixed with integral water proofing compound as per manufacturer’s instructions including finishing of surfaces even and smooth without using extra cement, complete all as specified and directed. Note :- WPC shall be measured & paid separately under respective item

M&L for 20 mm thick rendering in two layers on stone masonry surfaces, or on other than fair surfaces of brick / PCC block masonry i.e 1st layer will be 10mm thick in CM 1:6 and 2nd layer will be 10mm thick in CM 1:4 mixed with integral water proofing compound as per manufacturer’s instructions including finishing of surfaces even and smooth without using extra cement, complete all as specified and directed. Note :- WPC shall be measured & paid separately under respective item

M&L for 20 mm thick rendering in two layers on stone masonry surfaces, or on other than fair surfaces of brick / PCC block masonry i.e 1st layer will be 10mm thick in CM 1:6 and 2nd layer will be 10mm thick in CM 1:4 including finishing of surfaces even and smooth without using extra cement, complete all as specified and directed.

Supply only liquid water proofing compound, complete all as specified and directed.

S&F in repair of white PVC low level flushing cistern 10 ltrs capacity including all internal fittings & waste coupling and pipes etc , complete as specified and directed.

S&F in repairs PVC connection 60cm long 15mm dia with 2 nos PVC nuts fixed , complete as specified and directed.

S&F in repairs looking mirror of size 600mmx 450 mm approved quality and make , mounted on 6 mm thick plywood commercial as backing and PVC capping on edges complete as directed by Engr-in-charge fixed with wooden plugs on wall with CP brass service & cap washers, complete as specified and directed.

S&F in repairs viterious china squatting pan orissa pattern size 580x440mm white integal foot resta & including supply & fixing 10 liters capacity PVC flushing cistern, low level & flush pipe with and including provision of concrete bedding of suitable mix & water proofing treatment etc complete with and including P trap of 100mm size, complete as specified and directed.

S&F in repairs vitreous china wash basin, white, flat back, size 550x400mm with brackets, inciuding cutting for & pinning in ends of brackets, including 32mm dia brass CP waste fitting and 32 mm dia low density polyethylene (LDPE) pressure pipe rating 6 Kg/sqcm complete as specified and directed.

S & F in repairs, vitreous china wash down water closet pan (pedestal pattern), white, 'P' or 'S' type, including 10 litres capacity PVC flushing cistern, low level, white, with inlet, ball valve, float & brackets, including flush pipe, PVC pipe 32mm dia & including plastic water closet white seat cover, closed pattern with flat bottem, & cover & Mild steel CP or aluminium anodised hinge device, complete as specified and directed.

S&F in repairs EWC seat cover of any pattern including cover and Mild steel chromium plated hinging devices of any colour, complete all as specified and directed.

S&F in replacement brass CP wall mixer 3-in-1 system with and including provision of both hand shower and overhead shower complete with 115 mm long bend pipe, connecting legs and wall flange conforming to CAT No.STE-107281 STELLA ESSCO (JAQUAR) or equivalent cat part from the makes as mentioned here-in-after, complete all as specified and directed.

S&F in replacement 15 mm size, fancy type, long body, CP brass bib taps with wall flange & aerator conforming to CAT No. SQT-512KN ESSCO (Jaquar) or equivalent cat part from the makes as mentioned here-in-after, complete all as specified and directed

S&F CP Soap dish CAT No. ACN-1131N Jaquar / BA-259 of Prayag or equivalent cat part from the makes as specified here in after, complete all as specified and directed.

S&F towel rail, 20mm dia, 600mm long incluidng brackets, chromium plated, fancy type conforming to CAT No ACN-1111SM of Jaquar / BA-50 of Prayag or equivalent cat part from the makes as specified here in after, complete all as specified and directed.

S&F health faucet, chromium plated, fancy type conforming to CAT No ALD-579 of Jaquar / BEA-81 of Prayag or equivalent cat part from the makes as specified here in after, complete all as specified and directed.

S&F in replacement angular type stop cock with flange conforming to CAT No. APR-101053 ESSCO of (Jaquar) / Cat No. 7210 or 7310 of Prayag or equivalent cat part from the makes as specified here in after, complete all as specified and directed

S&F toilet paper holder, chromium plated, fancy type conforming to CAT No ACN-1151N of Jaquar / BA-38 of Prayag or equivalent cat part from the makes as specified here in after, complete all as specified and directed.

S&F CP towel ring round with round flange conforming to CAT No ACN-1121 BN of Jaquar / 9218 of Prayag or equivalent cat part from the makes as specified here in after, complete all as specified and directed.

S&F in replacement 2 way bib cock, CP brass with wall flange conforming to CAT No. STE-107041, ESSCO (Jaquar) or equivalent cat part from the makes as specified here in after, complete all as specified and directed

S&F towel rack, 600mm long with lower hangers, stainless steel of make Jaquar CAT part No. AEC-1181FHS or or equivalent make as mentioned here-in-after, complete all as specified and directed.

S&F in repairs brass chromium plated shower rose 100 dia with 235 mm long arm with or without swivel joints, including fixing to steel pipe or union complete all as specified and directed.

S&F in repairs pillar taps, brass CP, long neck with aerator CAT No ORB-105001N ESSCO (Jaquar) or equivalent cat part from the makes as mentioned here-in-after, complete all as specified and directed.

S&F stainless steel Robe Hook (khuti) with 5 Hook complete all as specified and directed

S&F in repairs sink cock with swinging casted spout with aerator (Wall mounted model) conforming to CAT No. ORB-105347 ESSCO(Jaquar) or equivalent cat part from the makes as mentioned here-in-after, complete all as specified and directed

S&F in repair cascade type (coloured) floor mounted single piece water closet with PP Soft close Slim Seat Cover, hinges, Dual Flush Cistern Fittings, fixing Accessories and Accessories Set, Size 365x675x740 mm, Strap -220 mm pipe etc connected to pipe confirming to CAT No. ESC-WHT-851S220SPPSM ESSCO (Jaquar) or equivalent cat part from the makes as mentioned here-in-after, complete all as specified and directed

S&F in repairs, stainless steel plate rack of size 36inch x 30 inch x 10inch, made out of 0.63mm thick stainless steel sheet (Grade AISI 304 18/8), S S screws and round pipe, fixed to wall with screws complete all as specified and as directed

S&F in repairs flexibe waste pipe of 32 mm or 40 mm dia suitable for wash hand basins, sink etc of suitable length, complete all as specified and directed

S & F in repairs spindles of any size suitable for concealed mixer valves, stop valves, angle cock, fancy taps including knob heads complete all as directed by Engineer-in-Charge

S & F in repairs kitchen or laboratory sinks made of stainless steel 1mm thick sheet with plugs, washers, and wastes coupling, including bedding in cement mortar on to dwarf wall or including fixing cantilever brackets and connecting union to pipe, bowl size 560x460mm including coupling etc complete all as directed by Engineer-in-Charge

S & F gun metal gate valves (Class I), with iron wheel head, screwed both ends for iron pipe, ISI marked, all as specified and directed for the following bore dia of pipe:- (a) 15mm bore.

(b) 20mm bore.

(c) 25mm bore.

S&F in repair high density 40mm bore polythylene pipes (HDPE) of pressure rating 6 kg/cm2 fixed to wall or in floors with necessary socket, elbow & bend etc complete fixed to wall or in floors etc complete all as specified and directed.

S&F in repairs 20 mm bore aluminium powder coated curtain rod, medium weight complete all as specified and as directed

S&F in repairs aluminium powder coated fancy type bracket including end tops suitable for 20 mm bore curtain rod complete all as specified and directed.

S&F in repair stainless steel wire cloth 0.36 nominal dia of wire and average width of aperture 1.4mm and fixed with stanless steel stepple to wooden / steel frames, complete all as specified and directed.

S&F PVC (SWR) 110mm bore pipes, single socketed in any length with rubber ring joints laid in trenches or fixed to wall including dismantling of old unserviceable breaking up drain pipes PVC or AC set in CM or solvent, complete all as specified and directed. Note :- Rate quoted shall deemed to be inclusive of necessary scaffolding / security measures as the work is to be carried out for elevated height upto 12 mtr height building.

S&F PVC (SWR) 75mm bore pipes, single socketed in any length with rubber ring joints laid in trenches or fixed to wall including dismantling of old unserviceable breaking up drain pipes PVC or AC set in CM or solvent, complete all as specified and directed. Note :- Rate quoted shall deemed to be inclusive of necessary scaffolding / security measures as the work is to be carried out for elevated height upto 12 mtr height building.

S&F 110mm bore PVC (SWR) bends, complete all as speicified and directed.

S&F 75mm bore PVC (SWR) bends, complete all as speicified and directed.

S&F in repairs PVC (SWR) vent cowl 110mm bore, complete all as specified & directed.

S&F in repairs PVC (SWR) branch piece, (Double 'Y') equal or unequal of 110 mm bore, complete all as specified and directed

S&F in repairs PVC (SWR) branch piece, (Double 'Y') equal or unequal of 75mm bore, complete all as specified and directed

S&F in repairs PVC (SWR) gully trap 125x110mm, setting and jointing with solvent cement, complete all as specified and directed.

S&F 110mm PVC (SWR) WC connector with lip ring, complete all as specified and directed

S&F PVC (SWR), 75mm dia outlet multi floor trap with grating including jointing with solvent cement, complete all as specified and directed.

M&L for 75mm dia, PVC (SWR) floor trap with grating including jointing to waste pipe with solvent cement, fixed to cement concrete in type B1 1:2:4, complete all as specified and directed.

S&F 4 mm thick sheet glass, ordinary quality and glazing with oil putty in square n. exc 0.5 Sqm in each pane, including hacking out old broken glass if any (any thickness, quality & size), complete all as specified and directed.

Taking down chowkhat or frames n. exc. 1.5 sqm each with shutter without taking off shutter from the frame complete all as specified and directed.

Taking down chowkhat or frames exc. 1.5 sqm but n. exc. 4 sqm each with shutter without taking off shutter from the frame complete all as specified and directed.

Taking down shutters of any description exc 1.0 sqm and n exc 2 sqm complete all as specified & as directed

S&F pressed steel door frames of size 105X60 mm for doors with one or more rebates including necessary hold fasts – 06 Nos., 100mm size MS butt hinges- 03 Nos., lock strikes plate, including providing PCC type B-0, 1:2:4 (using 12.5 mm graded stone aggregate) to fill up the hollow portion of the frame & grouting of holdfasts complete all as specified and directed

S&F pressed steel door frames of size 125X60 mm for doors with one or more rebates including necessary hold fasts – 06 Nos., 100mm size MS butt hinges- 06 Nos., lock strikes plate, including providing PCC type B-0, 1:2:4 (using 12.5 mm graded stone aggregate) to fill up the hollow portion of the frame & grouting of holdfasts complete all as specified and directed

S & F 35 mm thick flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both side with and including 5mm thick, 1st Class hard wood teak beading all around on edging complete all as specified and directed

S & F 35 mm thick 2nd class hard wood glazed and skeleton shutters, divided into squares with plain, chamfered or rounded mitered and rebated sash bars any numbers, open rebated prepared to receive gauze, edges of framing plain, chamfered or rounded , fitted with cut and mitered beads for securing glass etc size of members of shutters in SSR Part- I, Section 8, Clause 8.24 (a), complete all as specified and directed

S&F solid PVC door frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet, reinforced with MS square tube and fixing in opening complete all as specified and directed

S&F factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of M.S tubes for top & bottom rails .M.S frame shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheet strip of 20 mm width struck inside with solvent cement for stiles and plain colour PVC sheets for top rail ,lock rail & bottom rail on either side & as gap insert for top rail & bottom rail ; Panelling of plain colour PVC sheet to be fitted in the M.S frame welded/scaled to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement and fixing in the frame as per manufacturers instructions and as directed by Engineer-in-Charge.

M&L for cleaning and removing all scale and dirt, etc, from tanks n. exc. 500 ltr capacity and from mouths of circulating pipes etc including writing of date of cleaning with synthetic enamel paint complete all as specified and directed.

M&L for cleaning and removing all scale and dirt, etc, from tanks exc. 500 ltrs but n. exc. 1000 ltr capacity and from mouths of circulating pipes etc including writing of date of cleaning with synthetic enamel paint complete all as specified and directed.

M&L for cleaning and removing all scale and dirt, etc, from tanks exc. 1000 ltrs but n. exc. 2000 ltr capacity and from mouths of circulating pipes etc including writing of date of cleaning with synthetic enamel paint complete all as specified and directed.

S&F 25/32mm bore ball valve high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball screwed for iron pipe and fixed (Minimum weight 455 gms), complete all as specified and directed.

S&F 20mm bore ball valve high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball screwed for iron pipe and fixed (Minimum weight 210 gms), complete all as specified and directed.

S&F 15mm bore ball valve high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball screwed for iron pipe and fixed (Minimum weight 142 gms), complete all as specified and directed.

M&L for cutting chases, pinning in, concrete block / brick / stone walling & making good to facing where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels etc. and cutting chases for concealed water tubing and making good, cutting n. exc. 10 cm girth, complete all as specified and directed.

S&F aluminium powder coated three track sliding window with two or more shutters with & including 4 mm thick tinted glass, one shutter of stainless steel mosquito proofing with good quality bearing, handle, lock etc using PVC beading etc using following sections of `Jindal Aluminum Ltd ' or equivalent in Ajit India Pvt Ltd or Crystal Bombay, as approved, fixing to stone masonary walls with & including Ist class hard wood teak plugs of size 20mmX20mm at an interval of 0.5m alround the track including drilling holes etc. by comprising of the following provisions, complete all as specified and directed. (a) Frame bottom 20620. (b) Frame top & side 20621. (c) Shutters top & bottom 20844 (d) Shutter inter lock 20724. (e) Handle (Side ) for 20606 shutters, (e) Handle (side) for 20606 Shutters

S&F aluminium powder coated ventilators / louvers 5mm thick x 10cm wide frosted glass strips including with following aluminium powder coated sections conforming to catalogue of JINDAl or equivalent in Ajit India Pvt Ltd or Crystal Bombay, as approved including rubber beading etc, , complete all as specified and directed:- (a) SP - 20048 (b) Glszing clips 19352

S&F for 200 mm aluminium anodised barrel tower bolts of extruded section complete all as specified and directed.

S&F 300mm length of bolt, aluminium alloy, anodised, sliding door bolts with hasp staple (bolt type) anf fixing clips of sheet, cast or extruded section and fixing bolts and sliding bolts of extruded sections or cast alluminium alloy, complete all as specified and directed.

S&F 100mm sizes mild steel butt hinges medium weight, cold rolled, complete all as specified and directed.

S&F 150 mm size extruded aluminium alloy handles, fabricated type, anodised, complete all as specified and directed.

S&F 150mm overall length of cover plate brass body door stopper and tongue with hard drawn steel spring, complete all as specified and directed.

S&F in repairs of 18/19 mm thick block board, grade I quality exterior grade type with decorative face veneer on both faces including lapping of edges fixed with screws to timber frame work as in CB partition and shelf and other works complete including dismantling of old unserviceable boards of any type complete all as specified and directed

S&F 0.9mm thick decorative laminates type 1 of surface finish, colour and pattern as approved, fixed with approved adhesive as per manufacturer's instructions, complete all as specified and directed.

S&F continuous (piano) hinges, mild steel, bright finish, width of flaps (When open) 30mm, complete all as specified and directed.

M&L for IInd class hard wood wrought plain fillets square, rectangular or triangular in section clean sawn secured with screws, sectional area exc. 13 Sqcm but n. exc 25 Sqcm etc complete including dismantling of timber fillets in cabinet / cupboard frame, complete all as specified and directed.

S&F in replacement 100 mm brass fancy type cupboard handle fixed with nuts, screws and washer of brass polished, complete all as specified and directed.

S&F in repairs Magnet catches and striking plate, complete all as specified and directed.

Taking up or down steel water tubing and connections including cleaning and re-fixing the same including new fittings and fixtures complete all as specified and directed for following size of pipe :- (a). 15mm dia bore.

(b). 20mm dia bore.

Supplying, fixing, jointing and testing galvanised steel tubing, medium grade including with all fitting such as bends, elbow, socket, reducer etc and fixed to wall, ceiling or laid in floor including Taking up or down steel water tubing and connections complete all as specified and as directed for the following sizes:- (a) 15 mm dia bore

(b). 20mm dia bore.

M&L for Cutting, screwing & threading of existing 15mm bore steel tubing for alterations or additions (Each cut measured) complete all as specified and directed

M&L for Cutting, screwing & threading of existing 20mm bore steel tubing for alterations or additions (Each cut measured) complete all as specified and directed

M&L for Cutting, screwing & threading of existing 25/32mm bore steel tubing for alterations or additions (Each cut measured) complete all as specified and directed

Ares Construction Company