Construction of Sports hostel at Kalaignar Centenary Boxing Academy Gopalapuram Chennai

Amount

Earth work excavation for foundation in all soils and sub-soils and to full depth as may be directed except in rock requiring blasting inclusive of shoring shuttering, bailing out water wherever necessary and depositing the surplus earth within the compound in places shown by the departmental officers with an initial lead of 10 mts and initial lift of 2 mts. and clearing and levelling the site, etc., complete complying with standard specification.

Supplying and filling in foundation, basement, etc with filling M-sand in layers of not more than 15 cm thick well watered, rammed and consolidated etc. complete complying with standard specification and as directed by the departmental officers.

Plain Cement Concrete 1:4:8 (One Cement, Four sand and eight hard broken stone jelly) using 40 mm gauge hard broken granite stone jelly for foundation including dewatering wherever necessary and laid in layers of not more than 15 cm thick well rammed, consolidated and curing etc. complete complying with standard specification

Dismantling RCC by manual / by using deploying machineries

Supplying and erecting centering for sides and soffits including necessary supports and strutting upto 3.29 M height for plane surfaces as detailed below in all floors with all cross bracings using Mild Steel sheets of size 90 x 60 cm and 10 BG stiffened with welded Mild Steel angle of size 25mm x 25mm x 3 mm for boarding laid over silver oak joists of size 10cm x 6.50 cm spaced at abote 90 cm centre to centre and supported by casurina props of 10cm to 13 cm dia spaced at not more than 75 cm centre to centre etc. complete complying with the standard specificaiton. (Payment for centering shall be given after the concrete is laid

For column footing plinth beam bed blocks templates staircase, steps piers, raft beam, raft slab etc.

For Plane surfaces such as RCC floor slab, roof slab, beams, lintels, bed blocks, landing slab, waist slab, portico slabs and beams, et

For plane surfaces such as rectangular or square RCC columns, sunshades, top and bottom slab of RCCSlab, etc.

Supplying, fabricating and placing in position Mild Steel / Ribbed Tor Steel grills for all RCC works as per design given including cost of steel and G.I. binding wire in all floors etc. complete complying with standard specification. (Contractor has to make his own arrangements for the supply of steel and binding wire)

Providing and laying in position, Standardised Concrete Mix M-25 Grade in accordance with IS:456-2000, using 20mm and down graded hard broken granite stone jelly for all RCC items of works with minimum cement content of 350 kg/mᶾ and maximum water cement ratio of 0.50, including admixture (plasticiser / super plasticiser) in recommended proportions as per IS:9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability with about (5.0 cu.m.) 7730 kg. of 20mm machine crushed stone jelly and with about (3.3 cu.m.) 5156 kg. of 10-12mm machine crushed stone jelly and with about (4.79 cu.m.) 7670 kg. of sand, but excluding cost of reinforcement grill and fabricating charges, centering and shuttering and also including laying, vibrating with mechanical vibrators, finishing, curing, etc. and providing fixtures like fan clamps in the RCC floor/ roof slabs wherever necessary without claiming extra, etc., complete complying with standard specification and as directed by the departmental officers. The coarse and fine aggregates to be used should comply with the requirements of IS Standards. (No separate payment will be made by the Department for the excess usage of materials).

Foundation

Ground Floor

First Floor

Second Floor

Brickwork in following cement mortar using best quality second-class ground molded chamber burnt bricks 9" x 4-1/2" x 3" for foundation and basement, including curing, etc., completely complying with standard specifications.

Ground Floor

First Floor

Second Floor

Brick partition walls of 11.50cm thickness using best quality II Class Ground Moulded Chamber Burnt Bricks of size 9" x 4-3/8" x 2-3/4" in Cement Mortar 1:3 (One Cement and Three Sand) using hoop iron reinforcement if found necessary including both side plastering and curing etc. complete and as directed by the departmental officers. (Hoop iron reinforcement will be measured and paid for separately)

Special ceiling plastering and finishing the exposed surface of all RCC items of work such as slabs, beams, sunshades, facia, canopy slab, staircase waist slab, landing slab etc., with Cement Mortar 1:3 (One Cement and Three Sand) 10mm thick including hacking the surfaces, providing cement mortar nosing, beading for sunshades, staircases, steps, landing slabs and curing, etc., in all floors complying with standard specification and as directed by the departmental officers

Plastering with Cement Mortar 1:5 (One cement and Five sand), 12mm thick in all floors including curing etc. complete complying with standard specification and as directed by the departmental officers.

Plastering with Cement Mortar 1:3 (One Cement and Three Sand) 12mm thick mixed with water proofing compound conforming to BIS at 2% by weight of cement used including finsihing, curing, etc., complete in all floors complying with standard specification and as directed by the departmental officers.

UPVC Window Specification: Supplying and fixing UPVC (Un-Plasticized Polyvinyl Chloride) Windows ofcasement type (open) from the profile the size of outer frame 60mm x 58mm and shutter profile are reinforcement with GI/1mm 125GSM and 100% corrosion free, the profiles are multi chambered sections with wall thick of 2mm. The EPDM rubber (black colour) covered with over all the edges of frame and shutter the shutter will be provided with Espag multi power point locks and also it operates as handle. The corners and joints should bewelded and cleaned. Radiations free pin headed plain or brown colour glass 4mm thick should be provided to the shutter and it should not allow leakage of water even at most ranging storms and should have key lockable action, security protective hinges, strong locking systems and as per size for arresting noise and energy loss. The connecting mechanism between sash and outer frame that enables opening of the window. The window should be fixed to the wall with 100% packing with screws and silicon packing all round the frames. The window should be got approved from the Executive Engineer before use on work

UPVC Ventilator Specification: Supplying and fixing UPVC (Un-Plasticized Polyvinyl Chloride) Louvered Ventilators of from the profile the size of outer frame 60mm x 58mm and shutter profile size of 60 x 78mm both profiles are reinforced with GI/1mm 125GSM and 100% corrosion free, the profile are multi chambered sections with wall thick of 2mm. The EPDM rubber (black colour) covered with all over the edges of frame and shutter. The corners and joints should be welded and cleaned. Radiations pin headed glass 4mm thick should be provided in the louvers. The window should be fixed to the wall with 100% packing with screws and silicon packing all round the frames. The ventilator should be got approved from the Executive Engineer before use on work

Stainless Steel (Salem Stainless Steel) Door Frame (Box Section using Stainless Steel Plate of 1.6mm thick) of size 100mm x 60mm with a rebate of 30 / 35mm x 15mm on one side of the frame including supplying and fixing dovetail splayed end stainless steel hold fast etc

Supply and fixing the solid core flush door shutters with commercial ply on both side with teak wood lipping alround 35mm thick including cost of furniture fitting such as 3 nos 4"brass butt hinges,2nos 6"brass tower bolts,2nos 4"brass handle, 1 no brass drop, single key shutter, mortice lock without night latch, 1 no door closer, 1 no brass door stopper, 1mm thick best quality lamination sheet etc., complete complying with standard specification.

Supply and fixing Mild Steel Grills for windows and ventilators etc., including the cost of mild steel angles, plates, rods, cost of welding charges and one coat of priming coat etc., complete.(The design should be got approved by the departmental officers.)

Paving the floor with best quality Double charged Vitrified Tiles of size 600 x 600 x 8mm of approved colour, shade and quality laid in cement mortar 1:3 (one cement and three sand) 20mm thick in all floors and the top pointed with the white cement mixed same colour pigments etc., complete complying with standard specification. (The make and brand of the tiles should be got approved by Executive Engineer before use on works)

Paving the floor with best quality Vitrified Tiles of size stainfree nano polish 600 x 600 x 8mm of approved colour, shade and quality laid in cement mortar 1:3 (one cement and three sand) 20mm thick in all floors and the top pointed with the white cement mixed same colour pigments etc., complete complying with standard specification. (The make and brand of the tiles should be got approved by Executive Engineer before use on works)

Dadooing walls with following best approved quality, Designed colour ceramic tiles of following sizes 1200x600x8mm set in Cement Mortar 1:2 (One Cement and Two sand) 10mm thick and pointing the joints with white cement mixed with colouring pigments at the rate of 0.40 Kg. / sq.m. neatly in all floors, curing, etc., complying with standard specification and as directed by the departmental officers.

Paving the floor with best approved quality fine polished Granite Stone Slabs of size 1200 x 600 of 18 / 20mm thick of Granite slabs (super fine polished with machine cut edges )Jet black and similar varieties with machine cut edges laid over a cement mortar bed of 20mm thick using cement mortar 1:3 (One cement and three sand) fixing the slabs with required cement slurry and laid in true right angles with minimum possible width of joints and pointing the joints with white cement mixed with mathcing colouring pigments etc., The granite stone slabs and other materials to be used shall be got approved by the Executive Engineer concerned before use on work, etc., complete as per standard speicification.

Weathering course in brick jelly lime concrete using broken brick jelly of size 20mm uniform gauge in pure slaked lime (no sand to be used) to the proportion of brick jelly to lime being 32:12.5 by volume and laid over the RCC roof slab in a single layer of required slope and finished by beating the concrete with wooden beaters of approved pattern, keeping the surface constantly wet by sprinkling lime jaggery water, etc., complete as per standard specification and as directed by the deparmental officers.

Finishing the top of roof with one course of machine pressed tiles of size 230mm x 230mm x 20mm of approved quality set in Cement Mortar 1:3 (One Cement and Three Sand) 12mm thick mixed with water proofing compound conforming to ISS at 2% by weight of cement used and the joints pointed neatly to full depth of tiles with the same cement mortar mixed with red oxide and water proofing compound including curing etc., complete complying with standard specification and as directed by the departmental officers

Painting two coats of newly plastered wall surface with ready mixed plastic emulsion paint of first class quality and of approved colour over a priming coat including thorough scrapping, clean removal of dirt, and including necessary plaster of paris putty, wherever required etc., complete complying with standard specification.

Painting two coats of newly plastered wall surface with ready mixed Exterior emulsion paint of first class quality and of approved colour over a priming coat including thorough scrapping, clean removal of dirt, and including necessary plaster of paris putty, wherever required etc., complete complying with standard specification.

Painting new iron works such as steel doors, windows, ventilators, window bars, balustrades etc., with two coats of best approved first quality and colour of synthetic enamel paint over one coat of red oxide priming coat in all floors including cost of priming coat etc., complete complying with standard specification. (The make, quality and colour of paint should be got approved by the Executive Engineer before use on works.)

Supply and installation of Anutone (or) Euivalent Brand of Acoustical False Ceiling of subtex nubby, square edge, glass fibre core fully encapsulated ceiling tile of size 595 x 595 x 15mm having volume density 120 Kgs / m3, weight 1.8 / 2.4 / 3 kg / m2 which is suspended by using 0.3mm thick skelet trelis T15 metal grid system. Skelet trelis T15 metal grid system of 600 x 600mm module includes skelet WA15 W30 wall angle with unequal flanges of 15 / 19mm, length 3000mm, fixed along the perimeter of walls with the help of nylon sleeves and suitable fasteners at 300mm centers. Then suspend the skelet MT15 W36 MainT with flange width 15mm, height 32mm and length 3600mm,from the soffit slab with help of soffit cleat and wire rod with leveling spring clip at 1200mm centres. Skelet CT15 W12 CrossT with flange width 15mm, height 26mm and length 1200mm is interlocked into the pre-cut slots in the Main T15 at 600mm centers in the perpendicular direction to the Main T15. Finally, the skelet CT15W06 CrossT with flange width 15mm, height 26mm and length 600mm are interlocked into the precut slots in the CT15W12 CrossT in direction parallel to the Main T15 to result in 600 x 600mm module. The subtex nubby square edge of size 595 x 595 x 15mm shall be placed into the grid size of 600 x 600mm. Ensure arrow marks behind the tiles are oriented in one direction to achieve uniform shade. The systems to achieve noise reduction coefficient not less than 0.9 NRC, so as to have an neat appearance as directed by the department offices. The cost includes, cost of material, cost of labour, scaffolding, transportation, conveyance, etc. complying to standard specication.

Supply&Fixing materials such as Gypsum board & Rockwool then attached to the frame to form the wall. As partition walls don’t support the structural load of the building, they can be more lightweight and flexible in design. They are used to create rooms, hallways, and other designated spaces inside a structure. Partition Gypsum Walls are constructed with stud sizes of 3.5", 5.5" (8.9, 14 cm) and stud spacings of 16", 24" (40.6, 61 cm). Overall heights for Partition Gypsum Walls are between 3'-12' (.91-3.66 m) with common heights of 8'-9' (2.44-2.74 m). the finished depth of a partition wall is typically 4.5", 6.5" (11.4, 16.5 cm). Include Putty and painting materials should be got approved from the Executive Engineer befoe use on work.

Providing, installing, and fixing 12 mm thick Toughened Glass Partition (Glass Make:- Saint Gobain) with all as per required arrangement & proper machine edge finish in angle & fixed in the flooring side with Aluminium 'U' channel . Glass panels to be formed as per approved modules 12 mm thick clear toughened glass edge polished and accurate designed holes to be installed by means of steel fittings of an approved make Saint Gobain / Asahi or equivalent. Including Floor spring (make:- Dorma or equivalent), lock-approved make, Door Handle on both sides (SS make), all works including labor, wastages, cost of scaffolding, finishing with frosted design fil,m etc. complete.

Providing, installation, and fixing 12 mm thick Toughened Glass (Glass Make:- Saint Gobain) DOORS up to 2.10 M with all as per required arrangement & proper machine edge finish in angle & fixed in the flooring side with Aluminium 'U' channel . Glass panels to be formed as per approved modules 12 mm thick clear toughened glass edge polished and accurate designed holes to be installed by means of steel fittings of an approved make Saint Gobain / Asahi or equivalent. Including Floor spring (make:- Dorma or equivalent), lock-approved make, Door Handle on both sides (SS make), all works including labor, wastages, cost of scaffolding, finishing with frosted design fil,m etc. complete.

Providing Cup-board Shutter with frame using termite / water proof plywood of 19mm thick over which laminated sheet of 0.8mm thick fixed inside the shutter and 1mm thick fixed in the outside of the shutter using fevicol along with necessary furniture fittings, such as, hydralic hinges, tower bolt, handles, multi purpose locks etc., as directed by the Departmental Officers. The design pattern, water proof plywood, laminate sheet and other materials should be got approved from the Executive Engineer befoe use on work.

Toilet Cubicle (of following standard dimension which includes 600mm door size width) made of heat, bacteria, water, chemical, scratch impact and anti bacterial resistant 12mm thick solid compact laminate panels tested by shriram Test House. Finish of the compact laminate should be suede/ *Raw silk, which includes doors, pilasters & intermediate panels finished with approved texture/shade as per the detail drawings & as per IS 2046 (Indian Standard) and as per fire retardant BS-476/97 standard. The product should have Green Guard Certificate. This also includes providing and fixing in position necessary hardware made out of Stainless steel (Grade 304) as per manufacturer’s specifications & Architects instructions like (1) Door Knob, (2) Gravity Hinges, (3) Thumb turn lockset indicators, (4) Coat hooks, (5) U-Channels, (6) SS-Shoe Box Plate (7) MS-Base Plate, (8) Top rail with Corner conntector (9) Rubber noise deafening tape (10) Screws & wall Plugs. The top fitting should consist of SS round top rail which will get fixed with pilasters, with SS panel tube holder, SS corner bend (connected with top rail) will be used on the corner of cubicle

Supply and Fixing Urinal Partition 1050mm Ht x 450mm W

Supply and Placing Bunker Bed (2model)

Six‐seater dining table Set Size of 1200x800x760 The table is made of 18mm Polished Teak & Veneer finish SS understructure as designed. WOODEN top attached to the understructure via UV disc. The Load bearing capacity of the table is 30 Kg

Supplying and fixing 50mm dia GI pipe forfollowing data including labour charges for cutting, welding and fixing with MS flats (excluding the cost of flat), etc., as directed by the departmental officers

Supplying and fixing 40mm dia GI pipe forfollowing data including labour charges for cutting, welding and fixing with MS flats (excluding the cost of flat), etc., as directed by the departmental officers

Supply and Fixing Pvc chain link fencing

Supply and Laying Acrylic coat

Supply and fixing in position white European Water Closet of approved make with low level flushing tank 10 litre capacity of best quality and approved make with 100mm P or S trap with double flapped rigid PVC seat cover with CP brass hinges etc. complete complying with standard specification and as directed by the Departmental officers (The EWC should be got approved by the Executive Engineer before use on works.

Supplying and fixing Lipped Mouth Porcelain Flat Back Urinal(white colour) of size 26.5x31.5x44cm with all accessories such as 32mm dia Bell Mouth PVC Connection, 15mm dia GM Wheel Value, 15mm dia 'B' Class GI Waste Water Pipe, 15mm dia Nylon Connection, 15mm dia Brass Nipple, and suitable screws, shellac etc., complete. The rate including cost of all materials, labour charges for fixing and transportation etc. completed as directed by Engineer-in-Charge.

Above / Below Counter Wash Basin with all accessories such as Cast Iron Brackets, 32mm dia CP Waste Coupling, Rubber Plug and Chain, 32mm dia ‘B’ Class GI Waste Pipe, 15mm dia GM Wheel Valve, 15mm dia Nylon Connection, 15mm dia Brass Nipples, 15mm CP Pillar Tap etc

Wash Hand Basin of size 550mm x 400mm with all accessories such as Cast Iron Brackets, 32mm dia CP Waste Coupling, Rubber Plug and Chain, 32mm dia ‘B’ Class GI Waste Pipe, 15mm dia GM Wheel Valve, 15mm dia Nylon Connection, 15mm dia Brass Nipples, 15mm CP Pillar Tap etc

Supplying and fixing of CP Two Way Bib Cock with Health Faucet ,wall hook & one metre long flexible tube including cutting and making good the walls wherever required etc complete. complying with standard specification and as directed by the Department officers. The quality and make of health faucet should be got approved by Concern department Engineer before use on work.

Supplying and fixing the best quality approved make of SS heavy duty long body Tap including cutting and making good walls wherever required etc.complete,complying with standerd specification and as directed by the department officers. The quality and make of angular stop cock should be got approved by concern department engineer before use on work.

Supplying & fixing in position 15 mm dia brass/ C.P screw down tape (Heavy duty) of approved make conforming to I.S. Specifications & quality including cost of shellac, thread etc., complying with standard specifications & including cutting & threading wherever necessary. (Taps should be got approved by the Executive Engineer before use on the work).

Supplying and fixing in position Mirror of size 600x450mm of approved quality and brand with necessary plastic back PVC frame with bottom stand using brass screws rawl plugs for fixing etc complete complying with standard specification and as directed by the Departmental officers. The colour of frame and quality of mirror should be got approved by the Executive Engineer before use on work

Supplying and fixing heavy duty 15mm CP shower unit comprising of CP 15mm dia hot & cold mixer with CP spout, overhead shower set comprising of CP shower arm, rose etc.,complete with CP wall flanges. The rate including cost of all materials, labour charges and transportation etc. completed as directed by Engineer-in-Charge.

Supplying and fixing Brass Chromium Plated Towel Rail 60cm long and 20mm dia with brackets of same materials including cost of teak wood plug & CP screws etc., complying with standard specification and as directed by the Department officers.

Supplying and fixing C.P. Robe hook fixing with necessary screws etc., complete. fixed on the toilet door complying with standard specification and as directed by the Department officers. The quality and make of coat hook should be got approved by Concern department Engineer before use on work.

Supplying and fixing Brass Chromium Plated Soap Tray of size 150mm x 100mm using rawl plug & brass screws for fixing etc., complete complying with standard specification and as directed by the Engineer Incharge before use on work.

Supplying & fixing of approved make GEYSER with necessary fittings. (20 Litres Capacity) Heating element 2 kw ( Rate as per Quote )

Supplying,installing,testing and commissioning of approved make CONCELD STOP COCK for toilet including neccesary accessories etc,complete,works include making require size curout in wall,and fixing the control box property,redoing the same etc,complete the quality and make of concealed stop cock should be got approved by concern department Engineer before use on work.

Supplying,installing,testing and commissioning best quality approved/equivalent make of Single Bowl with drain board 600X600X200 mm tainless steel sink with brass Chromium Plateds wivalty peex tended swing sink cock 32mm dia CP waste coupling, 32mm dia heavy duty waste hose with extension pipe, 15mm CP angle valve with CP inlet connection tube,CP wall flange, including necessary bracket set ccomplete complying with standard specification and as directed by the Department officers.The quality and make o fsink and brass CP coated swiv al type sink cock should be got approved by Concern department Engineer before use on work.

Supplying and fixing in position best quality PVC soil / waste pipes of various dia having 6 kg / sq.cm. pressure BIS mark and providing leak proof joints using PVC adhesives including fixing to the wall with special PVC / MS clamp, teak wood plugs, brass screws, etc., and making connection to all sanitary fittings, dismantling masonry / RCC works wherever found necessary and making the good dismantled portion to the original condition, including testing for any leakages, etc., complete complying with standard specifications. (The PVC pipes should be got approved by the Executive Engineer before use on works).

Supplying and fixing in position best quality PVC soil / waste pipes of various dia having 6 kg / sq.cm. pressure BIS mark and providing leak proof joints using PVC adhesives including fixing to the wall with special PVC / MS clamp, teak wood plugs, brass screws, etc., and making connection to all sanitary fittings, dismantling masonry / RCC works wherever found necessary and making the good dismantled portion to the original condition, including testing for any leakages, etc., complete complying with standard specifications. (The PVC pipes should be got approved by the Executive Engineer before use on works).

Supplying & fixing in position PVC Nahini / Floor trap of size 100x75mm including stainless steel gratings of approved brand & quality, fixed over a bed of brick jelly lime concrete 1:2:5 ( One part of lime, two parts of sand & five parts of 40 mm size brick jelly ) & finished with cement mortar 1:3 ( One cement & three sand ) including dismantling masonry works wherever found necessary & making good the damaged portions to the original condition & giving connections to the cast iron pipes etc., complete, complying with standard specification. (The PVC Nahini / Floor trap should be got approved by the Executive Engineer before use on works ).

Supplying, laying and jointing CPVC pipes SDR 11(having working pressure 10 kg. / sq.cm) of approved quality and best variety conforming to BIS of the following dia including cutting, threading and fixing CPVC specials using CPVC adhesives and fixing into wall with teak wood plugs, CPVC clamps and screws making holes on the wall (or) drilling holes in the roof and making good the dismantled portion to original condition with necessary brick work / cement concrete and plastering neatly wherever necessary with necessary scaffolding charges upto 4 metre height above ground level, etc., complete complying with standard specifications. The CPVC pipes shall be got approved by Executive Engineer before use on works. Internal & Vertical

Supplying, laying, jointing, testing & Commissioning of UPVC Schedule 80 pressure pipes as per ASTM D 1785 with Sch 80 Fittings as per specifications, jointing with hold tite / super tite & tefflon tape and complete with fittings such as sockets, unions, reducers long or short bends, elbows, nipples flanges,checknuts,etc. Pressure testing of piping and back filling of trench complete as required. The quoted rate shall include necessary earth works, fittings like Tees, Bends, Offsets etc., G.I. brackets with pvc coated GI clamps, nuts & bolts, anchor fasteners, grip bolts, GI threaded, rods, etc., complete for external pipes. (For under ground or above ground external water supply piping.) Vertical & External

Supplying, installing, testing and commissioning of approved make full way lever operated forged brass ball valve of brass body with forged brass hard chromeplated steel ball tested to a pressure not less than 20 Kg / sqcm with threaded joints complete.

Supply ,erection and testing & commisioning of 2HP Monoblock pumpset in the capacity of max 3 bar Pressure pumps fitted with bronze impellers and having delivery size of 40mm - 430V along with 3mts cable and manufactures standard control panel which is mandatory and as directed by the officer incharge.( Terrace Booster Pump)

Supply, Installation, Testing and Commissioning of the following distribution boards shall be designed for 415V, 3Ph, 50Hz, 4 wire AC system sheet steel, dust and vermin proof suitable for wall mounting type (recessed) compartmentalized designed and fabricated as per standard OEM manufacture thickness CRCA sheet steel for main frame, folded sections and load bearing numbers , CRCA sheet steel for doors and covers with suitable knockouts for incoming and outgoing cable/ conduits provisions. body earthing terminals with powder coated painting , danger board,sign writing including minor civil works etc as required as per the technical specifications. Note: All DBs are not less than IP 42. The double door type 12 Way TPN Compartmental Horizontal ( 7 Segment Phase Segregation ) MCB DB Incoming-63 A TPN MCB 'C' Curve – 1 No. Outgoings-63 A DP 30 mA RCBO – 3 Nos. (Each 63A DP 30 mA RCBO consist of 36 Nos of 6/10A 10 KA SP MCB 'C' Curve )

Supply and fixing of 4 way Vertical Triple pole and neutral MCB sheet steel enclosure distribution board with double door (metal) with 1 no. 63A 4P MCB Isolator as incoming and 12 nos. 6A to 32A SP MCB as outgoing on suitable angle iron frame on wall with earth connection only. Higher End

Supply and fixing of 12 way single pole and neutral MCB sheet steel enclosure distribution board with double door (metal) with 1 no. 32A DP MCB switch as incoming and 10 nos. 6A to 32A SP MCB as outgoing in flush with wall with earth connection only. Higher End

Wiring with 2 x1.5 sq.mm. (22/0.3) PVC insulated single core unsheathed FRLS copper conductor of 1100 V grade in suitable PVC rigid pipe Concealed in wall and ceiling with PVC accessories with Module GI switch box in flush with wall with 6A one way module switch with module front plate continuous earth wire connection by 1.5 sq.mm. PVC insulated SC unsheathed copper wire and making good of the concealed portion with suitable colour for Concealed PVC Light point / Fan point (for electronic regulator) ( 6points / Coil) Higher End (SD-283)

Wiring with 2 x1.5 sq.mm. PVC insulated single core unsheathed FRLS copper conductor of 1100 V grade in suitable PVC rigid pipe on wall and ceiling and switch drop portion PVC rigid pipe concealed in wall with PVC accessories with Module GI switch box in flush with wall with 6A one way module switch with module front plate with continuous earth wire connection of 1.5 sq.mm copper wire with painting of Suitable colour for PVC Light point / fan point (for electronic regulator) ( 4 points / Coil) Higher End

Wiring with 2 x1.5 sq.mm. PVC insulated single core unsheathed FRLS copper conductor of 1100 V grade in suitable PVC rigid pipe on wall and ceiling and switch drop portion PVC rigid pipe concealed in wall with PVC accessories with Module GI switch box in flush wall with 6A one way module switch with module front plate with continuous earth wire connection of 1.5 sq.mm copper wire with painting of Suitable colour for PVC Light point / fan point (for electronic regulator) ( 6 points / Coil) Higher End

Supply and Run of 2 of 4 sq.mm. PVC insulated SC unsheathed FRLS copper conductor of 1100 V grade in suitable PVC rigid pipe Concealed in wall and ceiling with continuous earth wire connection by 4 sq.mm. PVC insulated SC unsheathed FRLS copper wire and making good of the concealed portion

Supply and Run of 2 of 2.5 sq.mm. PVC insulated SC unsheathed FRLS copper conductor of 1100 V grade in suitable PVC rigid pipe Concealed in wall and ceiling with continuous earth wire connection of 2.5 sq.mm copper wire and making good of the concealed portion

Supply and run of 50mm Dia HDPE pipe of 4kgf/cm2 approved quality and best variety conforming to ISS and ISI mark below ground in HDPE pipes.

Supply and Clamping of 2C X 6 sq.mm PVC armoured LTUG cable in a trench to be excavated at a depth of 0.75 metre putting 0.15 mt. Layer of sand and covering the cable completely with bricks and sand and refilling the earth to make good.

Supply and Clamping of 4 x 10 sq.mm. PVC armoured LTUG cable in suitable size HDPE pipe in a trench to be excavated at a depth of 0.75 metre and refilling the earth to make good.

Supply and Clamping of 4 x 16 sq.mm. PVC armoured LTUG cable in suitable size HDPE pipe in a trench to be excavated at a depth of 0.75 metre and refilling the earth to make good.

Supply and Clamping of 3 1/2 x 25 sq.mm. PVC armoured LTUG cable in suitable size HDPE pipe in a trench to be excavated at a depth of 0.75 metre and refilling the earth to make good.

Supply and Clamping of 3 1/2 x 35 sq.mm. PVC armoured LTUG cable in suitable size HDPE pipe in a trench to be excavated at a depth of 0.75 metre and refilling the earth to make good..

Supply and fixing of brass cable gland for 2C x 6 sq.mm PVC LTUG armoured cable with earth connection with necessary accessories etc

Supply and fixing of brass cable gland for 4C x 10 sq.mm PVC LTUG armoured cable with earth connection with necessary accessories etc.

Supply and fixing of brass cable gland for 4C x 16 sq.mm PVC LTUG armoured cable with earth connection with necessary accessories etc

Supply and fixing of brass cable gland for 31/2C x 25 sq.mm PVC LTUG armoured cable with earth connection with necessary accessories etc

Supply and providing cable end termination of 3-1/2x25sq.mm.PVC LT UG aluminium armoured cable with necessary aluminium cable sockets by crimping etc with electrical connection complete

Supply and run of 25mm x 6.25mm Aluminium flat with necessary clamps / supports on wall / floor / ground for earth connection and etc to complete the work.

Supply and run of 2 of No.8 SWG GI wire for guarding with cradle with No.8SWG GI wire at the equal interval of 1.5 meter and etc to complete the work

supply and fixing of 36W LED 2x2 square type Recessed fitting with LED (Lower end) on false Ceiling with suitable hanging support from ceiling with PVC unsheathed copper leads from terminals to the fitting.

Supply and Fixing of 20W 4feet LED Tube Fitting with TW round blocks on wall or ceiling with PVC unsheathed copper leads from terminals to the fitting and etc to complete the work

Supply and fixing of External wall washing light 15W fitting on floor with PVC unsheathed copper leads from terminals to the fitting and to complete necessary accessories and etc to complete the work.

supply and fixing of 200W LED Flood Light (pickle ball court light) fitting with LED (Lower end) with 32mm dia. GI pipe (class B) with 1 no.32 mm GI bend complete on the existing post/ on wall with PVC unsheathed copper leads with MS clamps and with painting, IP Rating IP65+ (dust/rainproof), Beam Angle 90°–120° (wide flood).

Supply and fixing of 1200mm (48") sweep AC Ceiling fan 5star rated complete (Higher end) with 2module 100w fan step regulator (Higher end) with 1meter down rod with fan clamp with side plates and cross arm of size 450mm (18").

supply and fixing of 450mm (16") sweep Wall Mounted Fan High speed complete with 2 module 50W fan step regulator (Higher end). Rated Speed 1360 Revolution per minute, Air Delivery 72 m³/min

Supply and fixing of 2 nos.6A two module 5 pin socket , 2 nos. 6A one module switch on suitable module surface mounting Box (GI ) with module cover plate (plastic) on wall with connections. Higher End( SD-381)

Supply and fixing of 2 nos.6A two module 5 pin socket , 2 nos. 6A one module switch on suitable module surface mounting Box (GI ) with module cover plate (plastic) on wall with connections. Higher End

Supply and fixing of 3 nos.6A two module 5 pin socket , 3 nos. 6A one module switch on suitable module surface mounting Box (GI ) with module cover plate (plastic) on wall with connections. Higher End

Supply and fixing of 1 no.6/16A two module socket , 1 no. 16A one module switch with module cover plate (plastic) on suitable module concealed Box (GI ) in flush with wall with connections. Higher End

Supply and fixing of 2 nos.6/16A two module socket , 2 nos. 16A one module switch on suitable module surface mounting Box (GI ) with module cover plate (plastic) on wall with connections. Higher End

Supply and fixing of 3 nos.6/16A two module socket , 3 nos. 16A one module switch on suitable module surface mounting Box (GI ) with module cover plate (plastic) on wall with connections. Higher End

Supply and fixing of 1 No 63A 5Pin 3 Phase Metal Clad socket outlet with plug Top and controlled by 63A 4P MCB on suitable concealed Box (GI ) in flush with wall with connection and with necessory accessories etc to complete the work. Higher End

Supply and fixing of 1 No 40 5Pin 3 Phase Metal Clad socket outlet with plug Top and controlled by 40A 4P MCB on suitable concealed Box (GI ) in flush with wall with connection and with necessory accessories etc to complete the work.

Supply and fixing of 1 No 32 5Pin 3 Phase Metal Clad socket outlet with plug Top and controlled by 40A 4P MCB on suitable concealed Box (GI ) in flush with wall with connection and with necessory accessories etc to complete the work.

Supply,Installation, testing and commissioning of Ladder Cable Tray, GI, 1.6 mm thick up to 450mm 2mm thick above 450mm for Electrical Cable with GI Angle/Hitech Suitable threaded rods with Anchor fasteners, Clamps, bolts,nuts including all the necessary fastener etc., to suit site conditions as required.

Supply,Installation, testing and commissioning of Perforated Cable Tray, GI, 1.6 mm thick up to 450mm 2mm thick above 450mm for Data and voice/Electrical Cable with GI Angle/Hitech suitable threaded rods with Anchor fasteners, Clamps, bolts,nuts including all the necessary fastener etc., to suit site conditions as required.

Supply and installation of 2KVA UPS with 24V, 120Ah battery along with circuit wiring for 24 port Lan Switch with following specifications Single Phase UPS (Single Phase In & Single Phase Out) Capacity - System with Battery - 2 Hours back up UPS: pure sine wave output, battery charging indication, over load indication, low battery indication and with deep discharge and short circuit protection. Battery: Lead-Acid tubular battery with Low maintenance, High backup, Heavy gauge terminals and with first filling of distilled water.

Engraved metal labels shall be provided on all incoming and outgoing feeders. Single line circuit diagram showing the arrangements of circuit inside the distribution board shall be pasted on inside of the panel door and covered with transparent laminated plastic sheet.

Supply, installation, testing and commissioning of Propeller Fan

Supply and Fixing Hoshizaki 3 Door Under Counter Freezers-FTW- 186 MS4, 400 L. Capacity - 400 L, Type Of Freezer - Compact, Power Source - Electricity, Energy Consumption - 230V AC / 50Hz Number Of Shelves - 4

Supply and Fixing FALMARC DHC 90-A | Filter-Less + Dry Heat Auto Clean Technology | Gesture Control SKU FALMARCDHC90-A Filter-Less + Dry Heat Auto Clean Technology Unique Designed with Black Tempered Glass Gesture / Touch Controls with Digital Display Metal Blower + Metal Housing Automatic Glass Opening Vent System Long LED Strip Light Stainless Steel Oil Collector Wider Chamber Entrance With Special Noise Reducer Double Ball Bearing System Dual Vent Suction Fully Concealed Motor (Copper) Noise Level : 68 dBA(max) Designed Max Airflow (upto): 1480 Nm3/h Air Outlet – 180 mm Size: 90 cm

Carbon-di- oxide type fire extinguisher of 4.5 kgs. Capacity, CO2 gas filled in brand new seamless cylinder with powder coated finish, made out of Manganese steel, with wheel type valve, discharge nozzle, bend & one meter long braided high pressure discharge hose which should have a minimum bursting pressure of 14 kg & fitted with ABS discharge horn & handle on the body fully charged, wal mounting bracket etc. complete, confirming to IS 15683 make.M-0852

ABC type extinguisher with chromium plated gunmetal nozzle on the top of the fire extinguisher for discharge of liquid & chromium bottom gunmetal union (cap) at the fire extinguisher with handle fixed at the center, complete with bracket fixing screws, spanner & one filling. Extinguisher should bear ISI 15683 make.M-0851

EMERGENCY EXIT (400mmx150mm double side)

FIRE EXTINGUISHER (100mmx150mm single side)

FIRE EXIT (400mmx150mm double side)

EXIT (400mmx150mm double side)

MANUAL CALL POINT (100mmx150mm single side)

EVACUATION PLAN with AUTO GLOW in A2-

SREE AMMAN LOGISTICS (BID ID -1411472)

V SATHYAMOORTHY CO (BID ID -1425360)

CMK Projects Private Ltd., (BID ID -1425440)