REPAIR TO COMPOUND WALL, FOOTPATH, HARDSTANDING, INTERLOCKING, ROLLING SHUTTER, GATES, ROOF TRUSS AND OTHER MISC WORKS AT AF STN CHANDINAGAR IN AOR OF GE (AF) FARIDABAD

Amount

Taking down cement plaster on brick or stone walls including racking out joints,hacking for key scrubbing down with water etc complete all as specified and directed Engineer-in-Charge.

Demolition of brick work built in cement mortar in any position including all quoins, arches & pillars etc complete all as specified and directed Engineer-in-Charge.

M&L for brick work with sub class 'B' bricks straight or curved on plan exceeding 6m mean radius built in cement mortar 1:6 complete all as specified and directed Engineer-in-Charge.

M&L for rendering in 15mm thick with CM (1:4) on concrete/brick surfaces finished even and smooth without extra cement mixed with WPC @ 3% by weight of Cement complete all as specified and directed Engineer-in-Charge. Note : (WPC will be Measured and paid separetely)

Supply only integral water proofing compound complete all as specified and directed Engineer-in-Charge.

M&L for preparation of old treated plastered or concrete surfaces of wall and applying two coats of weather coat/exterior emulsion complete all as specified and directed Engineer-in-Charge.

Removing/cleaning of sand/silt, mud,etc under culvert and in the drain of any width and length in soft/loose soil including depositing of removed material from site at a distance exc 900 m and n exc 1000 m deposited complete all as specified and directed Engineer-in-Charge.

Demolition of cement concrete (unreinforced) in ground floors and pavings not exc 15cm thickness (below or above ground level) complete all as specified and directed Engineer-in-Charge.

M&L PCC 1:4:8 type D-2 (40mm graded stone aggregate ) for sub base 75mm thick complete all as specified and directed Engineer-in-Charge.

M&L for PCC (1:2:4) type B1 using 20 mm graded stone aggregate 40 mm thick finish by using extra cement as in flooring laid in panels complete all as specified and directed Engineer-in-Charge.

Demolition of cement concrete of any description and in any position not otherwise specificially provided for complete all as specified and directed Engineer-in-Charge.

M & L plain cement concrete 1:2:4 type B-1 using 20 mm graded stone aggregate in coping/Benching incl necessary from work and finishing of exposed surface complete all as specified and directed Engineer-in-Charge.

Demolition of reinforced cement concrete of any descrption and in any position not otherwise specifically provided for complete all as specified and directed Engineer-in-Charge.

M&L for 35 mm thick precast 1:2:4 type B-0 (using 12.50 mm gradded stone aggregate ) cement concree jalli including all mouldings set in cement mortar 1 :4 complete all as specified and directed Engineer-in-Charge.

M&L for Providing precast cement concrete 1:2:4 type B-1 with (using 20mm graded stone agg) as in landings, cover slabs (for manholes etc). Chulah hoods, chajjas, water troughs, mangers, shelves and similar articles with plain faces and set in cement mortar 1:4 complete all as specified and directed Engineer-in-Charge.

M & L mild steel TMT bars 8 mm to 10 mm dia cut to length bent to shape required incl cracking bending spirally, hooking end and binding with & incl MS wire 0.9 mm dia etc complete all as specified and directed Engineer-in-Charge.

M&L for 75 mm thick cement concrete, 1:2:4 Type B-1 (using 20 mm graded stone aggregate) as in floors, paving etc, finishing the surface even and smooth with using extra cement and including use and waste of form work complete all as specified and directed Engineer-in-Charge.

M&L for 60 mm thick precast cement concrete coloured interlocking tiles of grade M-35 any shape and size confirming to IS 15658-2006 with grey cement and pigment in floors / pavements incl 30 mm thick sand cushioning complete all as specified and directed Engineer-in-Charge.

M&L for coloured Chequered cement concrete glazed/glossy finisjed tiles 300x300x25 mm thick, with white cement and pigments, set, jointed and pointed in neat cement slurry in floors over and including screed bed 20 mm thick in CM 1:6 complete all as specified and directed Engineer-in-Charge.

Dismantling of mild steel work of any description including barbed wire complete all as specified and directed Engineer-in-Charge.

M/L for Framed work such as grills, gratings etc., with ends of bars shouldered and/or riveted, or forget into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe 410-0 or Fe 310-0 complete all as specified and directed Engineer-in-Charge.

Dismantling posts or struts of angle iron any section, including taking out embedded portion in Concrete, brick work, masonry, etc complete all as specified and directed Engineer-in-Charge.

Dismantling fencing wire mesh, any type complete all as specified and directed Engineer-in-Charge.

M&L for PCC 1:2:4 type B1 (using 20 mm graded stone aggregate as in for fixing angle iron and coping including necessary form work) complete all as specified and directed Engineer-in-Charge.

S&F MS work as in post and strutt and fencing, drilled and countersunk for balusters running bars for doors balusters,noising to steps including embeding in concrete and screwing etc. wind ties for roof including securing bolts,posts and struts in fencing including cutting tops to shape as directed drilling hoes nothcing for wire etc flat iron fillets ( for securing wire mesh ) including all necessary drilling bolting or riveting etc. and similar work conforming to Fe - 290 Gde E - 165 complete all as specified and directed Engineer-in-Charge.

M&L for providing and fixing concentrina spiral coil fencing with punched tape concentrina coil 600 mm dia and 6 m max openable length, upto 3 m height of wall with angle iron Y shaped with 9 horizontal RBT reinforced barbed wire studied with GI staples and GI clips to retain horizontal incl necessary bolts or GI barbed wire tied to angle iron, all complete as per direction of EIC, with reinforced barbed wire tape (RBT)/spring core (2.5 mm thick) wire of tensile strength of 165 kg/sqmm with tape (0.52mm thick) and weight 43.47 gm/m including taking down of old unserviceable concertina coil ccomplete all as specified and directed Engineer-in-Charge.

S&F in repair two strand galvanised steel barbed wire 2.24mm dia barbed with 2mm dia bars @ 75mm spaciang and fixed to any type started rails strained bolts incl securing or tying at closing with and provn of galvanised mild steel wire staples or steel pins complete all as specified and directed Engineer-in-Charge.

Supply only Chain link MS galvanised fencing, any size or type complete all as specified and directed Engineer-in-Charge.

Fixing only chain link fencing including line wires, any mesh, size and type to any type of standards, rails, straining bolts, etc. including provission of binding wire complete all as specified and directed Engineer-in-Charge.

M&L in applying two coats of synthetic enamel paint over a coat of red oxide primer to new steel and iron surfaces over 10cm in width or girth including preparation of surfaces complete all as specified and directed Engineer-in-Charge.

M&L for Precast cement concrete PCC 1:2:4 type B-1 block for road side curb stone as per sample approved by GE for road side kerb stone and for laying and setting in CM 1:4 including demolition of old PCC kerb stone complete all as specified and directed Engineer-in-Charge.

M&L for preparation of new or previously untreated plsatered or concrete surfaces and applying two coats of weather coat over a coat of primer complete all as specified and directed Engineer-in-Charge.

M&L for washed stone grit plaster on exterior walls in two layers, under layer 12mm cement plaster 1:4 (1 cement: 4 coarse sand) furrowing the under layer with scratching tool, applying cement slurry on the under layer @ 3kg of cement per square metre, top layer 15mm cement plaster 1:1/2:2 (1 cement: 1/2 coarse sand: 2 stone chipping 10mm nominal size) in panels with groove all around as per approved pattern including scrubbing and washing, the top layer with brushes and water to expose the stone chippings complete all as specified (Payment for providing grooves shall be made separately) including complete taking down of old damaged washed stone grit plaster upto masonry face of walls complete all as specified and directed Engineer-in-Charge.

M&L for forming groove of uniform size 15mm wide and 15mm deep in the top layer of washed stone grit plaster as per approved pattern using wooden battens, nailed to the under layer including removal of wooden battens, repair to the edges of panels and finishing the groove complete all as specified and directed Engineer-in-Charge.

M&L for preparation of new/previously untreated washed stone grit plaster on exterior walls by brooming down or steel wire brushing scrubbing down smoke soot, moulds, moss and efflorescence salts and treating oil and greasy spots removing dust, dirt and all loose scales of existing finishing and applying two coats of exterior acrylic emulsion water based (weather proof coat) paint on wall over a coat of primer water based/primer for weather coat complete all as specified and directed Engineer-in-Charge.

M&L for preparation of new or previously untreated plsatered or concrete surfaces and applying two coats of weather coat over a coat of primer complete all as specified and directed Engineer-in-Charge.

S&F 1.25mm thickness of laths steel rolling shutters, without ball bearing as specified including top cover, anchoring rod, hasp, staple and including gear operated type with bevel gear box and crank handle for rolling shutters and one shop coat of primer erected in position as indicated, complete all as specified and directed Engineer-in-Charge.

S&F Safety lever locks mild steel with 4 leavers for rolling shutters complete all as specified and directed Engineer-in-Charge.

Dismantling of plain or corrugated steel sheeting, any gauge, thickness, including Nainital or similar pattern roof covering complete all as specified and directed Engineer-in-Charge.

S&F Pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50 mm of an colour having tensile strength of 550 Mpa as in roof covering fixed on curved truss, fixed with self tapping screw complete all as specified and directed Engineer-in-Charge.

S&F Pre-painted galvalume aluminium zinc coating GI based plain steel sheet 0.50mm of an colour having tensile strength of 550Mpa as in roof covering fixed on curved truss, gutters etc fixed with self tapping screw complete all as specified and directed Engineer-in-Charge.

Supply and fixing of Polycarbonate double wall one side UV coated roofing sheet, 6mm thick, 1.3kg/SqM, Dark Grey/Opal white or other approved colour with all standard accessories like AL Key hole profile, C-cap, vent tape, Rubber beading, Chrome star screws, etc. complete all as specified and directed Engineer-in-Charge.

M&L for cut outs/ metal sign board of dogs Size 1.2m X 1.5m PVDF aluminium composite panels with fire resistent mineral filled core material printed with vinayl OR print with 3 M retro reflective tapes on ACP Sheet fixed on the ACP Sheet with the help of high bond double side taps Of 3M Grey VHB taps 2 mm thick complete all as specified and directed Engineer-in-Charge. Note: coloure and Type of dogs choice shall be approved by GE.

M&L for 3d Stainless steel LED lighted letters OR print with 3 M retro reflective tapes on ACP Sheet above 12 inch complete all as specified and directed Engineer-in-Charge. Note: Size shall be approved by GE.

Dismantling wall and ceiling boards (fibre, pulp, insulation etc) any thickness, including cover fillets and grid frame work complete all as specified and directed Engineer-in-Charge.

M&L for Providing and fixing in true horizontal level 605 mm. X 605 mm. false ceiling system manufactured by M/s. Armstrong World Industries or as approved by GE, using hot dipped galvanized steel section, exposed surface with pre-coated capping, main tee of size 24 x 32 mm., having 0.27 mm gauge at every 1200 mm. centre to centre maximum and rotary stitched cross tee of size 24 x 27 mm, having 0.27 mm gauge at every 600 mm. c/c. and sub cross tee of size 24 x 27 mm, having 0.25 mm gauge at 1200 mm c/c. and wall angle of size 19 x 19 mm., having 0.35 mm gauge fixed to the periphery of the wall. The above grid is suspended at every 1200mm c/c. in both directions using 2.0 mm complete all as specified and directed Engineer-in-Charge.

M&L for FISSURED TEGULAR Edge mineral fibre ceiling tiles 600X600 mm manufactured by M/s. Armstrong World Industries or as approved by GE, of size 600mmx600mmx12 to 15 mm having NRC 0.55, Light reflectance of >84% (WT), thermal conductivity k = 0.052-0.057 W/m0K, Humidity Resistance of 99% , having Fire Performance CLASS O / CLASS 1 (BS 476) complete all as specified and directed Engineer-in-Charge.

M&L for Steel work in tubular trusses and purlins including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to IS 1161-1979 grade St.-240 complete all as specified and directed Engineer-in-Charge.

M&L for Structural steel, rolled section such as joist, beam, channel, angle, tee, in available lengths Fe 410-W(Gde-E-250) quality-A complete all as specified and directed Engineer-in-Charge.

M&L for preparation of newly plastered surfaces and applying two coats of cement base paint over a coat of alkali resistant primer complete all as specified and directed Engineer-in-Charge.

High Tech Metal India

laxmi enterprises

Singh Associates

AARSINFRATECH

M/S Ashoka Engineers and contractors

NAVEEN KUMAR TYAGI