SPL REPAIRS TO BLOCK NO. 278 MOHAMMEDI LINES OFFRS MD ACCN AND PROVN OF TOILET BLOCK COMPLEX AT MHMD AREA UNDER GE GOLCONDA

Amount

Dismantling of Stone slabs and tiles of any description of laid dry or laid and pointed or thickness in floors, aprons etc. complete all as specified and as directed

M & L for 20 mm thick Granite (of any type) work (table rubbed and polished) as in steps, jambs, pillars, window-cills, cooking platforms,over 15 mm thick screed bed in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite etc complete all as specified and as directed.

Demolition of cement concrete reinforced in ground floors and pavings n exc 15cm thickness (reinforcement cut as required to facilitate demolition) and removing debrish from site complete all as specified and as directed.

M&L for RCC Type B1, (1:2:4) (20 mm graded stone aggregate) in slabs supported on walls, beams, landings, balconies, canopies, deck slabs and, shelves and similar works etc complete all as specified and directed.

M&L for TMT bars 10 mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

M&L for mild steel TMT bars 6 to 8mm dia and over, cut to length, bent to shape required, inlcuding cranking, bending spirally for hooping for columns, hooking ends and binding with mild steel wire (annealed) not less than 0.9mm dia complete all as specified and directed.

All as per item No. 06 but 5mm dia and over upto and including 10mm dia in stirrups, spacers and binders/tempreture bar etc including other works.

Use & waste of formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work as flat finishing to rough finished surface of concrete complete all as specified and directed.

S&F stainless steel wall hanging kitchen utencils rack ( non magnetic type ) of 0.6mm thick (23 gauge) sheet of size 36'' x 30'' x 10'' complete all as specified and directed.

S&F in repairs sinks (non megnetic) with drainage board made of stainless steel lmm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 915mm x 460mm bowl size 410mm x 330mm x 160mm including necessary fittings complete all as specified and directed.

S&F in repairs for 18 to 19mm thick prelaminated particle board, interior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination, fixed with screws to timber frame work complete all as specified and directed.

S&F Continuous (piano) hinges, mild steel, bright finish or electro galvanised Width of flaps (when open) in 40mm complete all as specified and directed.

Demolition of PCC in ground floor or paving of any description n.exc. 15cm thickness (Un reinforced) below or above GL and removing debrish from site complete all as specified and directed..

M&L for 75mm thick PCC 1:3:6 type C2 using 40mm graded stone agg in plinth protection, finished even and smooth without using extra cement complete all as specified and directed.

M&L for 75mm thick PCC 1:4:8 type D2 using 40mm graded stone aggregate in sub base of floor, finished even & fair without using extra cement complete all as specified and directed.

M&L for 25mm thick PCC 1:2:4 Type B0 (using 12.50 mm graded stone aggregate) below tiles for levelling of existing surface complete all as directed.

M&L for Vitrified light shade ceramic tiles 10 mm thick (square/ rectanglar ) polished, area of each tile not exceding 0.36 sqm , in floor/wall etc. set and jointed in neat cement slurry and pointed with white or coloured cement to match including 15mm thick screed bed in CM (1:6) complete all as specified and directed.

M & L for Non - skid coloured ceramic tiles 7 to 8 mm thick (square/rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match etc including 15mm thick screed bed in CM (1:6) complete all as specified and directed.

M&L glazed ceramic coloured tiles digital series with combination of dark & light colour in vertical surface, size 250x375x7mm thick laid over and including back coat 10mm thick in CM 1:4, set and and jointed in cement slurry and pointed with white or coloured cement to match complete all as specified and directed.

M & L for Machine cut machine polished kota stone slab as in flooring 20-25mm thick over 15mm thick in CM (1:6) screed bed laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab as in treads of staircase including bull nosing and cutting 3 Nos grooves 2mm deep etc complete all as specified and directed.

M & L for Machine cut Kota stone slab 20-25mm thick in riser of steps, skirting, dado and pillar laid over and including back coat 10mm thick in CM 1:4, set and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing etc complete all as specified and directed.

M & L for Machine pressed precast conctete interlocking paver block any shape and size confirming to IS 15658-2006 of 80mm thickness M-40 Grade, with grey cement and pigment, etc laid over and including 50mm thick crushed sand cushioning watered and consolidated complete all as specified and directed.

Taking down cement plaster on brick wall/stone wall etc, racking out joints, hacking for key & scrubbing with water completely and M&L for rendering 10mm thick in CM 1:6 on fair faces of brick walls finished the surface even and smooth without using extra cement including prepartion of newly plastered surfaces of walls and applying two coats of oil bound distemper over a coat of 1.5mm thick wall care putty including a coat of alkali resistant primer complete all as specified and directed.

Taking down cement plaster on brick wall/stone wall etc, racking out joints, hacking for key & scrubbing with water completely and M&L rendering 15mm thick in CM 1:4 mixed with WPC on fair faces of brick walls, surface finished even and smooth without using extra cement including preparation of new plastered surfaces and applying two coats of exterior weather coat emulsion over a coat of weather coat exterior primer complete all as specified and directed.

Taking down cement plaster on ceiling etc, racking out joints, hacking for key & scrubbing with water completely and M&L for rendering 5mm thick in CM 1:3 on fair faces of brick surfaces of ceiling finished the surface fair and even and including prepartion of newly plastered surfaces of ceiling and applying three coats of white wash complete all as specified and directed.

M&L for complete removel of existing treatment on walls and applying two coat of oil bound distemper over a coat of 1.5mm thick wall care putty including a coat of alkali resistant primer complete all as specified and directed

M&L for complete removal of existing treatment on ceiling and applying two coats of white wash complete all as specified and directed

M&L for complete removal of existing treatment on walls and applying two coats of exterior weather coat emulsion over a coat of weather coat exterior primer complete all as specified and directed.

M&L for preparation of old surface of steel & iron surfaces of any description not otherwise described, over 10cm width or girth and applying one coats of synthetic enamel paint complete all as specified and directed.

Taking down chowkats or frames with shutters (without taking off shutters from the frame) area not exceeding 1.50 Sqm each complete all as specified and as directed.

Taking down chowkats or frames with shutters (without taking off shutters from the frame) area exceeding 1.50 Sqm but not exceeding 4.0 Sqm each complete all as specified and as directed.

Taking down shutters of any description area not exceeding 1.00 Sqm each complete all as specified and as directed.

Taking down shutters of any description area exceeding 1.0 sqm but n. exc. 2.0 Sqm each complete all as specified and as directed.

M&L for 2nd class hard wood plain, solid, straight chowkats and frames, wrought, framed rebated on the solid, rounded or chamfered put together with glue pinned at joints complete all as specified and as directed.

S&F for Bands, straps, supports or stays for rainwater, ventilating pipes, including bolts, if required; hooks (stay), heavy, for large gates; hook and pintle hinges; large hasps and staples; chains; hand made sliding bolts; clamps; hold fasts; wall ties; hooks for hanging fans; plain angle cleats for securing purlins to wood trusses or rafters; knee piece inserts; two way and three way straps, plate washers and similar small articles conforming to Fe 410-0 or Fe 310-0 complete all as specified and as directed.

M & L for PCC 1:3:6, type C-1 (using 20 mm graded stone aggregate) as in copings, bed blocks for hold fasts and the like including weathering, slightly rounded or chamfered angles and throating including necessary form work and making good the disturbed portion complete all as specified and as directed.

S&F of 30mm thick factory made Flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides complete all as specified and directed.

M&L 2nd class hard wood plain framed factory-made panel shutter 35 mm thick (two or three panels) with lock rail and panel of 12mm veneered particle board with commercial veneering on both faces, the size of rail & style as per IS 1003 (Part-I) Kiln seasoned and chemically pressure treated.

S&F 2nd class HW factory made 35mm thick Glazed and skeleton shutters,divided into squares open rebated and prepared to receive glass, gauze, etc. (without sash bars), edges of framing plain, chamfered or rounded. fitted with cut and mitred beads for securing glass, etc.; sizes of me-mbers of shutters as specified in SSR Part I, Section 8, clause 8.24 (a); supplied and fitted to chowkats complete all as specified and directed.

M&L for powder coated (Thickness or powder coating not less than 50 micron) anodised aluminium frame for doors, windows, ventilators with one or more rebates including joining cleat for fixing, etc complete, as specified and directed.

M & L for Powder coated (Thickness or powder coating not less than 50 micron) Anodised aluminium window and ventilator shutters,hanging type without sash bar, aluminium section weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws,handles,stoppers etc. complete all as specified and directed.

S&F 4.0mm thick sheet glass ordinary quality and glazing with wooden beads or oil putty in square not exc. 0.50 Sqm in each pane complete all as specified and directed.

S&F 100 mm size butt hinges extruded aluminium alloy with galvanised mild steel hinge pin, anodised and fixed, type B-21 complete all as specified and as directed.

S&F 100 mm size MS butt hinges medium weight cold rolled complete all as specified and as directed.

S&F 200mm Aluminium anodised, barrel tower bolts of extruded section and fixed and fixed complete all as specified and directed.

S&F Extruded aluminium alloy handles, fabricated type, anodised of size 150mm complete all as pecified and as directed.

S & F for Extruded aluminium alloy handles, fabricated type, anodised, Size of handle in 100 mm,etc complete all as spd and directed.

S&F 150mm Aluminium anodised, barrel tower bolts of extruded section and fixed and fixed complete all as specified and directed.

S&F Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed of size 300mm complete all as specified and as directed.

S&F in repairs 150mm Aluminium anodised, barrel tower bolts of extruded section and fixed and fixed complete all as specified and directed.

S&F in repair Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed of size 300mm complete all as specified and directed.

S&F in repairs Butt hinges medium weight cold rolled mild steel and fixed in 100 mm complete all as specified and directed.

M&L for preparation of new wooden surfaces and applying two coats of synthetic enamel paint over a coat of pink primer on new wood surfaces width or girth exc 10cm complete all as specified and directed.

M&L for preparation of old wood surfaces and applying one coat of synthetic enamel paint over width or girth exc 10cm complete all as specified and directed.

S&F PVC door frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with MS square tube suppling fixing in opening etc. complete all as specified and directed.

S&F solid PVC Panel Door shutter 30mm thick style consisting of Frame made out of M.S Tube for top & Bottom rails, MS Frame shall be covered with heat moulded, Plain colour PVC’C’ channel having a PVC Sheets strip of 20mm width struck inside with solvent cement for stiles and plain colour PVC sheets for Top rail, lock rail bottom rail on either side and as gap insert for top rail and bottom rail, paneling of plain colour 5mm thick PVC sheet fitted in the MS Frame, welded/ sealed to stiles and rail with suitable PVC sheet beading and jointed together with solvent cement all as per manufacture instruction complete all as specified and directed.

S&F 3 mm thick sheet glass, ordinary quality and glazing with wooden beading, rubber beading with screws or oil putty in square/rectangular not exceeding 0.50 sqm in each pane complete all as specified and directed.

S&F 3mm thick figured glass, pin head type andd glazing with wooden beads or oil putty in square not exc. 0.50 Sqm in each pane complete all as specified and directed.

S&F in Stainless steel wire cloth 0.36 mm nominal dia of wire & average width of aperture 1.40mm and fixed with tinned tack orgalvanised wire staples including necessary fittings complete all as specified and directed.

S&F for Vitreous China squatting pan , "Orissa" pattern size 580 X 440 mm white with intgrel footrest (excluding flushing cistern & flush pipe) including 'P' or 'S' trap complete including provision of cement concrete all as specified and directed.

S & F in repairs Vitreous China wash down water closet pan (padstal pattern) white (squatting pan & trap including connection to drain in or out going pipe and to flushing pipe anti shyphonic pipe etc completely, including sunken traetment with water proofing compound and filling of brick bats or coal complete all as specified and directed.

S & F in repairs plastic water closet seat , black, closed pattern with flat bottom & cover and mild steel chromium plated or aluminised hinging device complete all as specified and directed.

S&F in repairs PVC valveless syphonic action type flushing cistern 10 lit capacity low level white with inlet, ball valve, float and handle including brackets and 32mm PVC flush pipe complete all as specified and directed.

S&F for PVC valveless syphonic action type flushing cistern 10 lit capacity low level white with inlet, ball valve, float and handle including brackets and 32mm PVC flush pipe complete all as specified and directed.

S & F for Vitreous china bowl urinal flat back size of 465 x 355 x 265mm white (minimum) with grating and union for discharge pipe (excluding flushing cistern, flush pipe and waste pipe) complete including providing & fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with screws, pointing around urinal back in cement complete all as specified and directed.

S&F for Vitreous china wash basin, white, flat back size 550 x 400mm excluding taps, waste coupling, chain and plug and porcelain stopper but including one pair of MS bracket, cutting for and pinning in ends of brackets or erecting stand complete all as specified and directed.

S & F for 32mm waste fitting, brass, chromium plated for glazes waere sinks, basins etc with long screwed shanks and fy-nuts, flange end bedded in red lead cement and other end fixed complete all as specified and as directed.

S&F in rapairs 15mm dia health faucet with 1.5 mtr tube & hook complete all as specified and directed.

S&F in rapairs 15 mm bore two way Bib taps cast copper alloy chromium plated fancy type screwed down, screwed for iron pipe or for brass ferrule complete all as specified and directed.

S&F in repairs CP Paper Holder Complete all as specified and directed.

S&F in repairs for 110mm CP Grating complete all as specified and directed.

S&F in reapirs vitreous China wash basin, white, flat back, size 630x450mm excluding taps, waste, chain & plug and porcelain stopper but including brackets, complete all as specified and as directed

S&F in repair PVC Mirror cabinet of size 450x 300mm with door shutter complete all as specified.

S & F in repairs for fancy type Pillar Tap of 15mm bore, cast copper alloy, with capstan heads, chromium plated, screwed down, high pressure, with long screwed shanks and fly nuts, screwed for iron pipe complete all as specified and as directed.

S & F in repairs waste coupling of PTMT (half or full threaded), minimum weight 45gms, suitable for discharge pipe of 32mm bore complete all as specified and as directed.

S&F in repairs 15 mm dia of Brass chromium plated shower rose 125mm size any colour for fixing with 15 mm pipe (min weight 40 gms) as fixed complete all as specified and directed.

S&F in repairs of PTMT towel rail 600mm long fixed with and including Chromium plated brass screws and wooden/ plastic cleats complete all as specified and directed.

S & F in repairs for Brass CP mixer for mixing hot & cold water screwed down for iron pipe and fixed, Bore dia of pipe in 15 mm, etc complete all as specifed and directed.

S&F in repair 15 mm bore Bib taps cost copper alloy chromium plated fancy type screwed down, screwed for iron pipe or for brass ferrule complete all as specified and directed.

S&F in repairs PVC connection 15mm dia, 45 Cms long with brass ferrules on both ends fixed complete as specified and directed.

S&F for PVC waste pipe for urinal/WHB with complete fitting etc 32 mm dia.

S & F in repairs stop valve/angle cock 15mm dia cast copper alloy screwed down high pressure with crutch or butterfly handle screwed for both end for iron pipe or for union and fixed complete all as specified and directed.

S&F 1000 ltr Rotational moulded polyethylene water storage tanks (multi-layer) (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part I including dismantling existing PVC water tank, capacity 1000 Lit complete all as specified and directed.

S&F 1000 Ltr Rotational moulded polyethylene water storage tanks (multi-layer) (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part I complete all as specified and directed.

S & F in repairs 20mm dia Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed complete all as specified and directed.

S & F in repairs 25mm Ball brass valves, high pressure, with polythene float and fly- nut com-plete, scre-wed for iron pipe or brass ferrule complete all as specified and directed.

M&L 16 mm bore CPVC pipe with SDR 11 & plain CPVC SDR 11 fittings fixed to wall and ceiling in floor complete as specified including taking down existing u/s GI pipe line complete all as specified and directed.

M&L 20 mm bore CPVC pipe with SDR 11 & plain CPVC SDR 11 fittings fixed to wall and ceiling in floor complete as specified including taking down existing u/s GI pipe line complete all as specified and directed.

M&L for cutting chases, pinning in, making good to facings where required and pointing in cement mortor in 1:3 to ends or edges of landings, steps .cills, sunshades, shelves, lintels etc and cutting chases for concealed water tubing or concealed conduitwiring etc and making good cutting exc 10 cm but not exc 20 cm girth complete all as specified and directed.

Demolition of brick work or stone/ boulder masonry, built in cement mortar including all quoins, pillars etc. complete all as specified and directed.

M & L for brick work with sub-class `B' bricks, straight or curved on plan exceeding 6 M mean radius built in cement mortar 1:6 complete all as specified and directed.

M&L for brickwork with sub class ‘B’ bricks, straight or curved on plan to any radius in half brick thick walls built in cement mortar 1: 4 complete all as specified and directed.

S&F in repair powder coated docerative type aluminium curtain rod 25mm bore complete all as specified and directed.

S&F of powder coated curtain brackets fancy type suitable for 25mm bore including necessary fittings to wall complete all as specified and directed.

Dismantling of cast iron/AC/PVC pipes100/110mm dia, jointed in cement mortar and taking out of trenches if required and S&F for PVC(SWR) 110 mm bore pipe single socketed,in any length with rubber ring joints,laid or fixed in any position complete all as specified and directed.

Dismantling of cast iron/AC/PVC pipes 75 mm dia, jointed in cement mortar and taking out of trenches if required and S&F for PVC(SWR) 75 mm bore pipe single socketed,in any length with rubber ring joints,laid or fixed in any position complete all as specified and directed.

S&F in repair PVC (SWR) bends any radius 110 mm dia complete all as specified and directed.

S&F in repair PVC (SWR) bends any radius 75 mm dia complete all as specified and directed.

S&F in repair PVC (SWR) bends any radius 110 mm dia with door access complete all as specified and directed.

S&F in repair PVC (SWR) bends any radius 75 mm dia with access door complete all as specified and directed.

S&F in repair PVC (SWR) branch piece, single (single Y) equal or unequal any radious 110 mm dia with access door complete all as specified and directed.

S&F in repair PVC (SWR) branch piece, single (single Y) equal or unequal any radius 75 mm dia with access door complete all as specified and directed.

S&F in repairs PVC (SWR) Vent cowl 75mm dia complete all as specified and directed.

S&F in repairs PVC (SWR) Vent cowl 110mm dia complete all as specified and directed.

Demolition of cement concrete on roofs, floors (other than ground floors), beams, staircases, landing, chajjas and similar suspended work etc complete all as specified and directed.

M&L for Type E2 1:5:10 (Using 40 mm graded stone aggregate) in foundations, filling and mass concrete (sunken floor filling) complete all as specified and directed.

M&L 15mm thick rendering in cement mortar 1:3 mixed with WPC @ 3% by weight of cement on fair faces of brick or concrete surface etc including a coat of bitumen VG-10 @ 1.20 kg/sqm over a coat of bitumen primer 0.70 kg/sqm etc and M&L for APP modified pre-fabricated five layer water proofing membrane 3 mm thick not less than 3.60 kg/sqm complete all as specifed and directed. (Note: WPC will be paid separately)

M&L for APP based polymeric membrane minimum weighing 3Kg/sqm and minimum 3 mm thick reinforced with polyster non wove fabric (weight not less than 150 gms/sqm laid over primed surface including bitumnious primer conforming to IS -3384 applied @ 0.3 ltrs/sqm by forced application and finished with one coat of aluminium paint @ 100 ml/Sqm, 10 cm overlap fused uniformly by LPG torch flame, including rendering 10mm thick in cm 1:4 on concrete surfaces of roofs, parapet etc. finishing to surfaces even and smooth without using extra cement and provinding necessary slope with using WPC @ 3% by weight of cement complete incl taking down existing froof treatment and cement plaster of any description, roughing, preparing the surface by cleaning the surface with wire brushing scrubbinbg down with water to receive new treatment all as specified and directed. (NOTE : WPC will be measured and paid separately)

M&L for PCC 1:2:4 type B0 (using 12.5 mm graded stone aggregate) as in roof padding and finishing the surface even & smooth without using extra cement complete all as specifed and directed.

Supply only Integral Water Proofing Compound

M&L cement concrete 1:2:4, type B0, using 12.5 mm aggregate for chajja repairs in patch work,cobing etc including necessary formwork/scaffolding work etc complete all as specifed and directed.

S & F for for Steel rolling shutters, with out ball bearing, as specified including top cover, anchoring rod, hasp and staple and one shop coat of primer; erected in position as indicated, complete: push pull or manual type, thickness of laths in 1.25 mm etc complete all as specifed and directed.

Dismantling structural steel work including doors, gates but excluding framed truss, etc complete all as specifed and directed.

M&L for Preparation of new or previously untreated steel surfaces of any description, over 10 cm width or girth, not otherwise described and applying two coats of synthetic enamel paint over a coat of red oxide zinc chrome primer complete all as specifed and directed.

Excavation in trenches in soft / loose soil not exceeting 1.5 Mtr wide and not exceding 1.5 Mtr in depth and getting out for shafts wells, cesspits, manholes, pier holes, taking out / laying of cables, erection of poles / strut / stays etc and not exceeding 10 sqm on plan complete all as specified and directed.

Excavation in trenches in hard/dense soil not exceeting 1.5 Mtr wide and not exceding 1.5 Mtr in depth and getting out for taking out / laying of cables, pipes, erection of poles / strut / stays etc and not exceeding 10 sqm on plan complete all as specified and directed.

Returning, filling in the any type of soil including spreading, levelling, watering and ramming in layers not exc. 25 cms complete all as specified and directed.

Removing excavated material of any type of soil not exceeding 50 Mtr away and depositing where directed at a level not exceeding 1.5 mtr above the starting point complete all as specified and directed.

Material and labour for clean river sand cushioning in cable trenches over & under the cables, with river washed coarse sand, as per standard practice with proper compaction complete all as specified and directed. (Note: Punned thickness 18 cm shall be considered for payment as per para 19.75 of SSR Part-I).

M&L brick protection with common burnt bricks, sub class'B' of size 230x115x75mm for cable protection complete all as specified and directed.

M & L for PCC 1:4:8 type D-2 (using 40 mm graded crushed stone aggregates) as in foundations, fillings and mass concrete etc complete all as specified and as directed.

Spreading and levelling in layers n exc. 25cm thick and well ramming including watering as required complete all as specified and as directed.

M&L for 25mm thick damp proof course in cement concrete 1:2:4 Type B-0 (using 12.5mm crushed stone aggregate) to horizontal or vertical surfaces including necessary formwork complete all as specified and as directed.

M&L for RCC (Nominal Mix) Type B1 (1:2:4) (20mm graded stone aggregate) as in foundation, including rafts, footings, foundation beams, plinth beams, bases for columns etc; basement slabs, under reamed piles and mass concrete complete all as specified and directed.

M&L for RCC (Nominal Mix) Type B1 (1:2:4) (20mm graded stone aggregate) as in Columns, pillars, piers, posts and struts complete all as specified and directed.

M&L for RCC (Nominal Mix) Type B1 (1:2:4) (20mm graded stone aggregate) in beams, cantilevers, bressummers, lintels over 1.50 meter span complete all as specified and directed.

M&L for RCC (Nominal Mix) Type B1 (1:2:4) (20mm graded stone aggregate) in slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified and directed.

Use & waste of formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels cantilevers, shelves including supports, overhungs etc. also splays between floors and beams etc. as in rough finished surfaces complete all as specified and as directed.

Use & waste of formwork to chullah hoods, chajjas, troughs and similar items in cluding edges finishing rough finished surfaces of concrete complete all as specified and as directed.

M&L for hard core gauge n.exc 63mm broken stone deposited, spread and levelled in layers n.exc 15cm thick, watered and rammed to a true surfaces complete all as specified and as directed.

M&L for rendering 15 mm thick in CM (1:4) on fair faces of brick work or conrete surfaces/stone masonary and finishing the surfaces even and smooth without using extra cement and including preparation of newly plastered surfaces of walls and applying two coats of cement base paint complete all as specified and directed.

M&L for rendering 10 mm thick in CM (1:6) on fair faces of brick work or conrete surfaces/stone masonary and finishing the surfaces even and smooth without using extra cement and including preparing of newly plastered surfaces of wall and applying three coats of white wash complete all as specified and directed.

M & L for 5 mm thick cement plaster in CM (1:3) on ceiling surfaces and finish the surface fair and even without using extra cement and including preparing of newly plastered surfaces and applying three coats of white wash on ceiling complete all as specified and directed.

S&F of steel ventilators with top hung shutter glazed and gauzed and bottom half fixed including hinges, steel peg stay etc complete all as specified and directed.

S&F Towel Rail 600mm long of PTMT fixed with and including Chromium plated brass screws and wooden/plastic cleats (Minimum weight 190gms) complete all as specified and directed.

S & F for 15 mm bore fancy type pillar tap cast copper alloy chromium plated, with capstan heads, screwed down high pressure, with or without 'Hot' or "Cold' with long screwed shanks and fly-nuts, screwed for iron pipe and fixed complete all as specified and directed.

S & F for stop valves (angle cock) 15mm dia cast copper alloy, fancy type, chromium plated, screwed down high pressure with crutch or butterfly handle screwed for both end for iron pipe or for union and fixed all as specified and directed.

S & F for stop valves 15mm dia cast copper alloy, fancy type, chromium plated with long shank and cup (concealed type) screwed down high pressure with crutch or butterfly handle screwed for both end for iron pipe or for union and fixed all as specified and directed.

S&F for 15 mm bore Bib taps cost copper alloy, brass chromium plated, fancy type, screwed down, screwed for iron pipe or for brass ferrule complete all as specified and directed.

S&F for 15 mm dia of Brass chromium plated shower rose 125mm size any colour for fixing with 15 mm pipe (min weight 40 gms) as fixed complete all as specified and directed.

S & F for PTMT PVC connections 15mm dia and 600mm long with brass nuts complete all as specified and directed.

S&F for Soap dish, vitreous China white, size not lessthan 160x160x90mm complete all as specified and as directed.

S & F (concealed / open) 16mm outer dia CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors complete all as specified and as directed.

S & F (concealed / open) 20mm outer dia CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors complete all as specified and as directed.

S & F for 20mm dia Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed complete all as specified and directed.

S & F for 25mm dia Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed complete all as specified and directed.

S & F for 20mm Ball brass valves high pressure of PTMT with epoxy coated aluminium rod and high density plastic ball screwed for iron pipe and fixed or brass ferrule complete all as specified and directed.

S&F for PVC(SWR) 110 mm bore pipe single socketed,in any length with rubber ring joints,laid or fixed in any position complete all as specified and directed.

S&F for PVC(SWR) 75mm bore pipe single socketed,in any length with rubber ring joints,laid or fixed in any position complete all as specified and directed.

S&F for PVC (SWR) bends any radius 110 mm dia complete all as specified and directed.

S&F for PVC (SWR) bends any radius 75 mm dia complete all as specified and directed.

S&F for PVC (SWR) bends any radius 75mm dia with door access complete all as specified and directed.

S&F for PVC (SWR) branch piece, single (single T) equal or unequal any radious 110 mm dia with access door complete all as specified and directed.

S&F for PVC (SWR) branch piece, single (single T) equal or unequal any radius 75 mm dia with access door complete all as specified and directed.

S&F for PVC (SWR) Vent cowl 110mm dia complete all as specified and directed.

S & F for PVC (SWR) floor trap 75 mm bore, plain with grating doom including jointing with solvent cement complete all as specified and directed.

M&L salt glazed stone ware gully traps square or rounded mouthed type & fix 150 x 150 mm fixed in cement concrete complete.

M&L for cutting in to existing manholes for connecting new drains making good to pipe 100mm internal dia and rendering cutting out existing benching fir and forming banch channels (1/2 round or 3/4 section) in cement concrete 1:2:4 type B-1 using 20mm graded stone aggregates finished smooth and reforming benching complete all as specified and as directed.

Supplying and laying, connecting and testing steel water tubing of dia 25mm bore pipe medium grade ISI Marked and confirming to IS 1239 galvanised iron water tube with all fittings such as bends, elbows, tees, short pieces, connectors, back nuts, diminishing pieces, caps and plugs, unions etc laid in trenches, fixed to wall or ceiling etc complete all as specified and as directed.

Cutting existing steel tubing of size 50mm dia for alternations or additions (Each cut measured) complete all as specified and as directed.

Screwing existing steel tubing of size 50mm dia for alternations or additions (or lengthening screw on pipe to form connector) complete all as specified and as directed.

S & F for GI pipe, light grade, of size 40 mm dia including necessary fittings laid in trenches/fixed on wall/pole for LT cable protection complete all as speicifed and directed.

Taking down carefully existing point wiring of any description for (light, fan, sockets bells etc) complete including fittings such as sunken boxes, switches, sockets, ceiling rose, lamp holders, brackets, fittings, pendants, fan regulartors etc and making good the disturbed surface of walls, floors etc complete all as specified and directed.

M&L Point wiring for one light point/fan point/bell point controlled by one switch with two runs of 1.5 sqmm multistrand copper conductor cable PVC (FRLS) insulated sheathed copper conductor single core multi strand flexible cable and 1.50 sqmm PVC (FRLS) insulated sheathed copper conductor single core cable ( green colour) as earth lead in and including PVC rigid conduit with all fittings for concealed type on stone / brick, masonary walls, roof etc including new CI/MS sunken box of required size and all as directed by Engineer-in-Charge & 3 mm thick plastic laminated sheet for housing switches sockets, regulators etc. including cutting/running chases, pinning in and making good the disturbed surfaces to match with the existing specification, complete all as specified and directed.

All as per item No.165 but One 5 pin 5/6 Amps switch socket outlet on independent board complete all as specified and directed.

All as per item No.165 but One 5 pin 5/6 Amps switch socket outlet on same board complete all as specified and directed

All as per item No.165 but for One 5 pin 15 / 16 Amps switch socket outlet point on independent board with 2.5 sqmm PVC (FRLS) insulated unsheathed copper conductor single core multi stand flexible cable and 2.5 sqmm PVC (FRLS) insulated unsheathed copper conductor single core cable (green colour) as earth lead complete all as specified and directed.

M&L switch piano flush type single pole one way 5 Amps complete all as specified and directed.

M&L switch socket combination flush type 5 Amps Multipurpose 2 in 1, 3 pin/6 Amp flush type pin with porcelain base complete all as specified and directed.

M&L Switch socket combination 2 in 1 flush type universal 3 pin 6 & 16 Amps flush type complete all as specified and directed.

M&L lamp holder insulated body with back plate suitable for battern fittings complete all as specified and directed.

S&F Ceiling rose surface bakelite 65 x 50 mm 2/3 terminals complete all as specified and directed.

M & L for providing Point wiring with 1.5 sq. mm (nominal area) single core PVC insulated FRLS unsheathed multi-stranded copper conductor cable (maintaining colour code), 1100 volts grade in and including non metalic rigid PVC conduit medium grade with appropriate size with all fittings (ISI Marked) suitable for concealed wiring on stone/brick, masonary walls, roof etc including modular sunken box of adequate size with suitable modular plate cover for mounting modular switches, sockets, regulators, light fittings etc. complete with all fittings and accessories fixed to wall/ ceiling for one light/ fan/Exhaust points controlled by one oneway modular switches including one run 1.5 sqmm (nominal area) PVC insulated FRLS unsheathed multi-stranded copper conductor cable green in colour for earth continuity conductor connected to common earth dolly complete all as specified & directed.

All as per Item No.174 above but for one 3/5 pin 5/6 Amps modular socket outlet point on same board with other switches.

All as per Item No. 174 above but one 5 Amps 3/5 pin modular socket outlet on independent board

All as per Item No. 174 above but one module modular bell / buzzer point controlled by one push button on the same board with other switches or independent with cables 1.5 Sqmm size.

All as per Item No. 174 but for one 3 pin 15/6 Amps switch socket outlet point on independent board with 4.00 Sqmm PVC (FRLS) insulated unsheathed copper conductor single core multi stand flexible cable and 4.00 Sqmm PVC (FRLS) insulated unseathed copper conductor sinlge core (green colour) as earth lead complete all as specified and as directed.

S&F Modular switch, single pole, one way, 6 Amps one module complete all as specified and as directed.

S&F Modular 6A 3 pin universal socket outlet, 2 module complete all as specified and as directed.

S&F Modular switch, single pole, one way, 16 Amps with indicator one module complete all as specified and as directed.

S&F Modular socket outlet 2-in-1, 6/16 Amps, 2 module complete all as specified and as directed.

S&F modular bell push with indicator 5 Amps one module complete all as specified and as directed.

S&F bell ding dong AC single pole 230 volts complete all as specified and as directed.

S&F Lamp holder PVC polycarbonate type with back plate suitable for batten fittings complete all as specified and as directed.

S&F ceiling rose, 3 point /PVC/polycarbonate, isolated body complete all as specified and as directed.

S&F modular stepped type electronics fan regulator 220volts,100Watt complete all as specified and as directed.

S&F Aesthetically designed LED wall bracket light with B22d lamp holder including necessary connection all as specified and directed.

S&F 25W energy saving and environmental friendly long life LED building security street light made up of pressure die cast aluminium housing with high power LED, lens & toughened glass, potted driver and with efficacy of 120lm/W and with LDR Sensor, IP 66 protection including connection with twin twisted unsheathed PVC copper cable of suitable size complete all as specified and directed.

S&F modular blank plate one module complete all as specified and as directed.

S&F 14W INVERTER LED bulb of base B22d with color temp 6500K and upto 4 hrs backup all as specified and directed.

S&F 9 W LED bulb of base B22d with color temp 6500K all as specified and directed.

Supply and fixing LED street light fitting 35 Watt 230 V AC outdoor type with high pressure die cast aluminum hosing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 65/66 protection complete all as specified and directed.

S&F Wall mounted indoor decorative 20W LED 6000K (4 ft.), extruded aluminium batten in anodised finish with opal diffuser, IP20 heat sink provided for efficient heat dissipation and integrated electronic driver, lamp color white complete set including necessary connection with twin twisted unsheathed PVC copper cable of suitable size complete all as specified and directed.

S&F LED light fitting 1x20W, 220 Volts AC decorative box type with driver, holder including LED tube connecting up with three core flexible copper conductor calbe of suitable size from ceiling rose complete all as specified and as directed.

S & F for LED light fittings, 1x10 watts bulk head luminaires etc complete with all accessories and including connecting up with twin core twisted flexible PVC copper conduct cabe of 23/0.0076 from ceiling rose complete all as specified and as directed.

S&F in repair for Sheet metal enclosure vertical single door with 200 Amps rated bus bar, TPN, 4 ways, 240 Volts suitable for housing MCBs as incomer and SP MCBs as outgoing complete all as specified and as directed.

S&F in repairs for Sheet metal enclosure MCB distribution board including 200 Amps bus-bar single pole and neutral 240V, 8 Ways, suitable for housing MCBs double door complete all as specified and directed.

All as per item No- 198 above but SPN 4 way, 415 V complete all as specified and directed at site.

S&F in repairs for MCB SPN, 240V, 10KA 'C' curve, 32 Amps.

S&F in repairs for MCB SP, 240V, 10KA 'C' curve, 6 to 32 Amps.

S&F in repairs for MCB four pole, 240V, 10KA 'C' curve, 63 Amps.

Supply and drawn sub main wiring with two runs of 4 Sq mm single core PVC insulated FRLSH unsheathed cable upto and including 1100 volts grade with multistranded copper conductor drawn through and including rigid PVC conduit accessories conceald type on walls, floors etc including one run of 2.5 Sqmm PVC insulated copper conductor for earth continuity as green in colour wire and including taking down old one all as specified (Note : (i) Two runs of copper conductor and one run of copper earth wire including PVC conduct will be measured and paid as one unit only . (ii) Suitable size cable lugs copper fabricated will be deemed to be included in quoted rate only)

Supply and drawn sub main wiring with two runs of 6 Sq mm single core PVC insulated FRLSH unsheathed cable upto and including 1100 volts grade with multistranded copper conductor drawn through and including rigid PVC conduit accessories conceald type on walls, floors etc including one run of 4 Sqmm PVC insulated copper conductor for earth continuity as green in colour wire and including taking down old one all as specified (Note : (i) Two runs of copper conductor and one run of copper earth wire including PVC conduct will be measured and paid as one unit only . (ii) Suitable size cable lugs copper fabricated will be deemed to be included in quoted rate only)

S&F in repair bracket suitable for fixing of security light fitting made out from 40 mm bore GI pipe, medium grade 2 metre in length (approx), made to shape as required, fixed to pole/wall with MS flat iron clamp of size 25x4mm duly welded, bent to shape and making holes etc complete including necessary nuts, bolts & washer etc as required and all as specified and directed.

S&F in repair power unit with 20A MCB & Plug 240 volts complete for ACs & Geyser all as specified and directed.

S&F in repair Motor Starter 25A 240 volts complete for ACs & Geyser all as specified and directed.

Supply and fix Exhaust fan, steel body, steel body AC Single phase 230 V of size 300 mm sweep with blades, and frame and louvers complete all as specified and directed

Taking down & refixing of ceiling fan/ exhaust fan of any make, sweep and dismantling, cleaning , greasing, overhauling and providing two coat of synthetic enamel paint of existing colour and refixing to its existing place including connections with new flexible cable 3 core copper conductor complete after renovation. For Ceiling fan - adjustment for providing new down rod including new canopy, clamp, rubbr reel, capacitor,all as directed.

Supply, laying and testing cable XLPE Insulated ,screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 25.0 sq mm 4 core complete all as specified and directed

Supply, laying and testing cable XLPE Insulated ,screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 16.0 Sq mm 2 core complete all as specified and directed

Taking down water heater (Electric Geyser) of any type /make of 25/50 Ltrs capaciry after disconneting the existing electric wire, water pipe, inspecting the inner tank and components for necessary repairs including replacement of unserviceable of thermostat, heating element, base and apparatus plate assembly, cleaning and removal of scales etc servicing etc and re-assembling in all respects after replacing unsv parts / components and testing for proper working after repairs and fixing in the original place/ position duly connecting up water supply and electric supply including civil work for grouting etc complete all as specified and directed.

M&L, in repair, earthing complete with galvanized steel earth plate electrode of 60 cm x 60 cm x 6mm thick buried directly in ground [earth pit not less than 2.25 metre deep below normal ground level] with top edge of the plate not less than 1.5 m below normal ground level, connected to galvanized earth wire of 4mm dia by means of bolts, nuts, check nuts and washers of galvanized iron or steel all as shown in electrical plate No. 3 of MES SSR Part I all as specified and testing on completion including provision of earth lead protected by 15 mm dia light grade GI pipe & watering pipe shall be 20 mm bore medium grade GI pipe including all excavation and earth work, PCC pit with RCC cover, char coal, salt, funnel etc complete. Note:- Rate quoted by tenderers shall be deemed to include for following provisions-[i]. Excavation & earth work in any type of soil including removing of surplus material upto 50 m. [ii].PCC 1:3:6 type C1 using 20mm graded stone aggregate in pit & 40mm thick precast RCC 1:2:4 type B1 cover 50x50 cm with 8mm TMT bars @ 10 cm C/C both ways with handles.[iii]. Main earthing lead from earth electrode to test point upto 7.5 mtr.[iv]. Funnel with watering pipe [GI pipe] 20mm bore medium grade & copper lugs, charcoal & salt as reqd.[v]. GI protection pipe of size 15 mm bore light grade 7.5m.

Sri Associates

M/s cogent constructions

SANJEEV CONSTRUCTIONS

m/s s indra reddy constructions

BUILDWEL