Replacement of 5 No. Horizontal motors with pump of 80 HP in (4 No. ) in pump house of water treatment plant in BBMB water (storage tank) and 1 No horizontal motor with pump of 40 HP in Dobetta colony at Nangal Township

Amount

Removing/ Dismantling of complete pump and Horizontal Motor 80HP with control panel complete in all respect. (MR)

Supply, Erection, Testing and Commissioning of pull back type centrifugal Horizontal pump confirming to IS-5120/1977 with latest amendment if any having discharge of 192 M3/Hrs. against minimum head of 67 mtr. coupled with 80 HP or equivalent 3 phase induction electric motor with 1440 RPM, 440 volts, 50 Htz confirming for IS-325/1976 having suction of 200 mm and delivery of 150 mm used for drinking water and material composition have cast iron (pump casting), end suction (type of casting), bronze impeller, EN8 shaft, bronze gland with latest amendment if any on a common base frame, complete with all accessories along with control panel (L&T/BCH/Havel’s, PVC copper cable three core 25 Sq. mm, Main Switch ICTP 200 Amp complete in all respect). (MR)

Removing/ Dismantling of complete pump and motor 40 HP with control panel complete in all respect. (MR)

Supply, Erection, Testing and Commissioning of pull back type centrifugal Horizontal pump confirming to IS-5120/1977 with latest amendment if any having discharge of 55 LPS against minimum head of 35 mtr. coupled with 40 HP or equivalent 3 phase induction electric motor with 1410 RPM, 440 volts, 50 Htz confirming for IS-325/1976 having suction of 150 mm and delivery of 125 mm used for drinking water and material composition have cast iron (pump casting), end suction (type of casting), bronze impeller, EN8 shaft, bronze gland with latest amendment if any on a common base frame, complete with all accessories along with control panel (L&T/BCH/Havel’s, PVC copper cable three core 25 Sq. mm, Main Switch ICTP 200 Amp complete in all respect). (MR)

Dismantling concrete e) Reinforced Cement concrete (CSR Item No. 8.6 (e))

Reinforced cement concrete M-20 mechanically batch mixed using batch type concrete mixer as per IS:1791 and vibrated by needle vibrator but excluding steel reinforcement centring and shuttering in foundation and plinth. (CSR Item No. 10.15)

Shuttering for precast and plain or reinforced concrete blocks, wall plates, bedplates, shelves etc. (CSR Item No. 9.14)

Cold twisted deformed (Ribbed/ Tor Steel Bar) Bars Fe 500 grade as per IS 1786-2008, for R.C.C works, where not including in the complete rate of RCC including bending and placing in position complete. (CSR Item No. 18.18)

Earth work in excavation in foundations, trenches etc. in all kinds of soil where pick jumper work is not involved and not exceeding 2.0 metres depth including dressing of bottom and sides of trenches, stacking the excavated soil clear from the edge of excavation and subsequent filling around masonary in 15 cm layer with compaction including dispose of all surplus soil as directed within lead of 30 metres. (CSR Item No. 6.6)

Providing, laying, fixing, testing and commissioning of ‘C’ class heavy duty MS pipe conforming to Indian Standard IS: 1239/3589 including fittings like tees, bends, sockets, elbows, flanges, tapers, nuts bolts, gaskets etc. in ground with anti-corrosive treatment with wrapping costing tape (4 mm pypkote tape ) as per IS:10221 including cost of primer etc. excluding cost of excavation and refilling complete in all respect. c) 200 mm internal diameter (CSR Item No. 28.105 (c))

Providing, laying, fixing, testing and commissioning of ‘C’ class heavy duty MS pipe conforming to Indian Standard IS: 1239/3589 including fittings like tees, bends, sockets, elbows, flanges, tapers, nuts bolts, gaskets etc. in ground with anti-corrosive treatment with wrapping costing tape (4 mm pypkote tape ) as per IS:10221 including cost of primer etc. excluding cost of excavation and refilling complete in all respect. c) 200 mm internal diameter (labour rate) (CSR Item No. 28.105 (c))

Providing, laying, fixing, testing and commissioning of 'C' Class heavy duty MS Pipe conforming to Indian Standard IS : 1239/3589 including fittings like tees, bends, sockets, elbows, flanges, tapers, nuts bolts, gaskets etc. on surface and providing angle iron support or cement concrete block as support including painting with two or more coats of synthetic enamel paint of required shade complete in all respects. c) 200 mm internal diameter (CSR Item No. 28.106 (c))

Providing, laying, fixing, testing and commissioning of 'C' Class heavy duty MS Pipe conforming to Indian Standard IS : 1239/3589 including fittings like tees, bends, sockets, elbows, flanges, tapers, nuts bolts, gaskets etc. on surface and providing angle iron support or cement concrete block as support including painting with two or more coats of synthetic enamel paint of required shade complete in all respects. b) 150 mm internal diameter (CSR Item No. 28.106 (b))

Providing & fixing C.I/D.I Flanged end, stem of SS (AIS 1410) and Bronze(gunmetal) working parts Sluice Valves ISI marked 14846-2000, including jointing , testing & cost of Nut ,Bolt & insertion sheet, all carriage complete (with the approval of Engineer incharge). (B) Class PN-1.6 as per ISI d) 200mm i/d Sluice Valves flanged (CSR Item No. 28.27 –B (d))

Providing & fixing C.I/D.I Flanged end, stem of SS (AIS 1410) and Bronze(gunmetal) working parts Sluice Valves ISI marked 14846-2000, including jointing , testing & cost of Nut ,Bolt & insertion sheet, all carriage complete (with the approval of Engineer incharge). (B) Class PN-1.6 as per ISI (c) 150mm i/d Sluice Valves flanged (CSR Item No. 28.27 –B (c))

Proving & fixing ISI Marked Non-return valves flanged end class PN-1.0 as per IS:5312/2004 in pipe lines including jointing & cost of Nut Bolt , rubber insertion etc. complete. Note: If Non-return valves class PN-1.6 is used instead of class PN-1.0 , than 5% will be paid extra. (B) Class PN -1.0 as per ISI with gun metal flap (e) 200mm i/d Non – return valve (CSR Item No. 28.31-B (e))

Proving & fixing ISI Marked Non-return valves flanged end class PN-1.0 as per IS:5312/2004 in pipe lines including jointing & cost of Nut Bolt , rubber insertion etc. complete. Note: If Non-return valves class PN-1.6 is used instead of class PN-1.0 , than 5% will be paid extra. (B) Class PN -1.0 as per ISI with gun metal flap (d) 150mm i/d Non – return valve (CSR Item No. 28.31-B (d))

Bidder Name

Amount in Words

BIROKE BUILDERS PVT LTD

ANMOL KATYAL CONTRACTOR

Vijay Kumar C/O Vasudeva Electricals

ANMOL KATYAL CONTRACTOR

BIROKE BUILDERS PVT LTD