PROVN OF TECH STORE BUILDING, PROVN OF CERTAIN B/R WORKS AND PROVN OF INTERLOCKING TILES FOR HQ DSI AT AF STN PALAM UNDER GE (AF) PALAM DELHI CANTT-10

Amount

B/R Portion Surface excavation n exc 30cm deep and averaging 15cm deep and getting out in soft/loose soils.

Excavating in trenches, n exc 1.5 m wide and n exc 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sq m on plan and n exc 1.5 m in depth and getting out in soft/loose soil all as specified.

M&L for cement concrete type D-2, 1:4:8 (using 40mm graded stone aggregate) as in foundations, filling and mass concrete all as specified.

Formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter for rough finished surfaces of concrete complete.

Formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including sup- ports, overhangs, etc. also splays between floors and beams, etc for rough finished surfaces of concrete complete all as specified.

Formwork to edges of concrete flats, treads, breaks in floors, window cills, concrete railings, openings in concrete walls, floor and roofs n exc 20 cm wide and sides of RCC/ PCC bands in walls, horizontal or sloping and similar work exc 10cm but n exc 20cm wide for rough finished surfaces of concrete complete all as specified.

Form work to fair finished concrete flat surfaces of sides of pillars post columns complete in all as specified and directed

Formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping) for rough finished surfaces of concrete all as specified..

M&L for reinforced cement concrete (M-25 design mix) as in foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under-reamed piles and mass concrete complete all as specified..

M&L for reinforced cement concrete (M-25 design mix) as in columns, pillars, piers, posts and struts all as specified..

M&L for reinforced cement concrete (M-25 design mix) as in beams, cantilevers, bressummers, lintels over 1.5m span all as specified..

M&L for reinforced cement concrete (M-25 design mix) as in slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified.

M & L for Mild steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified.

All as per item No 13 above but 8 mm dia and over upto and including 10 mm dia in stirrups and binders etc complete in all as specified.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm in soil.

Removing excavated material/soil from site to outside MoD land complete.

M&L for 40mm thick damp proof course to horizontal or vertical surfaces including necessary formwork using cement concrete type B-0, 1:2:4 (12.5mm nominal size crushed and graded stone aggregate) mixed with water proofing compound as specifified and directed. (Note : Water proofing compound shall be measured & paid separately under supply only item)

M&L for applying evenly a coat of blown type bitumen at the rate of 1.50 kg per square metre and blinding with clean dry sand @ 0.05 cum per sqm all as specified.

M&L for polythene film, 50 micron thick, laid on a coat of bitumen primer @ 0.30 to 0.50 kg per sqm all as specified.

M&L for brick work with sub class B works, straight or curved on plan exceeding 6m mean radius, built in cement mortar 1:6 complete all specified.

Taking down cement or cement lime plaster of any descriptiion on brick/ stone or concrete surface including raking out joints, hacking for key, scrubbing down with water etc and removing the rubbish from site to outside MoD land.

M&L for rendering 15mm thick on fair faces of brick work or concrete surfaces of walls in cement mortar 1:6 including finishing surface even and smooth without using extra cement all as specified and directed.

M&L for rendering 15mm thick on fair faces of brick work or concrete surfaces of walls in cement mortar 1:4 including finishing surface even and fair without using extra cement all as specified and directed.

M&L for rendering 5mm thick on fair faces of brick work or concrete surfaces in ceiling in cement mortar 1:3 including finishing surface even and smooth without using extra cement all as specified and directed.

M&L for preparation of newly plastered or unplastered surfaces in ceiling and applying three coats of white wash all as specified.

M&L for preparation of newly plastered or unplastered surfaces and applying two coats of distemper oil emulsion on walls over a coat of wall primer over 3mm thick (avg thickness) wall care putty complete all as specified and as directed.

M&L for two coats of cement base paint including preparation of newly plastered surfaces of walls all as specified .

M&L for factory made pressed steel frames of size 105mm x 60mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc and cement concrete type B-O, (1:2:4) using 12.5mm graded stone aggregate in back filling of frames etc complete all as specified.

S&F for 35mm thick second class hard wood factory made plain framed, panelled shutter (two panel) with lock rail and panel of 9 mm B.W.P. commercial ply or 12 mm veneered particle board with commercial veneering on both faces. The size of rail and stile as per IS : 1003 (Part I), kiln seasoned and chemically pressure treated complete all as specified.

S&F for aluminium anodised, barrel tower bolts of extruded section of size 150mm

S&F for cast type anodised aluminium handles of size 150 mm.

S&F for 300mm long aluminium alloy, anodized, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts of extruded sections or cast aluminium alloy and fixed with screws complete all as specified.

S&F for factory made steel windows with side hung shutters including box type hinges with steel handle, and steel peg stay complete with glazing bars, dovetailed or welded including cutting holes in brick walls for inserting holdfasts and making good dismantalled portion in cement mortar (1:3) or cement concrete (1:2:4) type B-1 as required complete all as specified.

S&F for factory made steel windows with side hung shutters including box type hinges with steel handle, and steel peg stay complete without glazing bars, dovetailed or welded including cutting holes in brick walls for inserting holdfasts and making good dismantalled portion in cement mortar (1:3) or cement concrete (1:2:4) type B-1 as required complete all as specified.

S&F for 4mm thick sheet glass ordinary quality and glazing with oil putty and rubeer beading in square exc 0.5 Sqm in each pane.

M&L for preparation of newly wooden surface of any description not otherwise described over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer all as specified and directed.

M&L for preparation of newly steel surface of any description not otherwise described over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide zinc chromate primer all as specified and directed.

S&F for stainless steel wire cloth 0.36mm nominal dia of wire and and average width of aperture not more than 1.40mm fixed with stainless steel wire staples.

M&L for 100mm thick cement concrete type D-2, 1:4:8 (using 40mm graded stone aggregate) as in sub base including necessary form work complete all as specified.

M&L for sand filling under floors or in foundations including watering and consolidation in layers not exceeding 25cm.

M&L for 20 to 25mm thick machine cut kota stone slab flooring of size not less than 600mm x 600mm laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including mirror polished complete as in floor over and including 20 mm thick screed bed in cement mortar 1:4 all as specified.

All as per item No 41 above but as in steps, skirting, dada and piller including 10mm thick cement plaster in cement mortar 1:4 all as specified.

M&L for hardcore of gauge n.exc 63mm of broken stone or boulders deposited, spread and levelled in layers n.exc 75mm thick watered and well rammed to a true surface complete all as specified.

M&L for 75mm thick cement concrete 1:3:6 type C-2 using 20mm graded stone aggregate as in plinth protection including finished even and smooth surface without using extra cement and making joints 12 mm wide to the full depth of concrete at every 3 metres interval and at every change of direction and filling the same with & including bitumen 85/25 and sand in the proportion of (1:3 ) by weight complete all as specified.

M&L for 25mm thick cement concrete 1: 2 :4 type B-O (using 12.5mm graded stone aggregate) as in floor/sub base etc complete all as specified.

M&L for vitrified coloured (light shade) tiles 10 mm thick (square/ rectangular) polished, area of each tile not exceeding 0.36 sqm in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15mm thick screed bed in cement mortar 1:4 all as specified.

All as per item No 46 above but in vertical surface such as wall, skirting, dado etc including 10 mm thick cement plaster in cement mortar 1: 4 all as specified.

S&F for framed work such as grills, gratings etc with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe-290, Gde E-165 complete all as specified.

S&F for 0.80mm thick Mild steel, plain, black sheet in wall cladding, steel gates, doors and similar work, cut to size, holes punched including round headed screws, clout nails or rivets and fixed to wood or steel framing with plain 40 mm lap joints with riveted or welded seams including bending or turning up, mitred angles, etc as required complete.

Taking down of existing tarfelt and cement plaster of any description and thickness on roof top including flashing and junction of parapet and cleaning existing roof top surface by brooming , wire brushing including removing the debris from site to outside MoD land complete.

Dismantling of brick tiles single layer on roofs, laid dry or with cement mortar including removing the debris from site to outside MoD land complete.

Demolition of Mud in roofs, any thickness, including plastering and leeping (whether full thickness removed or only a part thereof) including removing the debris/mud from site to outside MoD land complete.

M&L for cement concrete type B-0, 1:2:4 (using 12.5mm graded stone aggregate) as in roof padding including finished the surface even and fair complete all as specified.

M&L for 15mm thick screed bed on concrete surface on roof in cement mortar 1:4 including finished even and smooth surface without using extra cement and mixing water proofing compound as per manufacturer's instructions complete all as specified (Note: Water proofing Compound shall be measured and paid seprately)

M&L for cement concrete 1:2:4 type B-1 (20mm graded stone aggregate) in roof kerbs or mud stops, rounded or chamfered on edges complete all as specified.

M&L for 3mm thick APP based modified prefabricated five layer and weighing not less than 3.6 Kg/Sqm water proofing membrane reinforced with polyester non woven fabric mat with 150 gm/sqm black laid over compatible bitumen primer conforming to IS-3488 @ 0.30 Ltr/ sqm over bonding material bitumen 85/25 @ 1.2 Kg/Sqm before laying membrane laid by torch application method with side overlap of 75 mm and over lap of 100 mm longtitudinally. At the junction of roof and parapet wall at a height of 100mm, a grove of 75mm wide and 65mm deep shall be made filled with cement and bituminious mastic including joints/overlap shall be sealed with hot bitumen 85/25 all as specified and directed by Engr-in-Charge.

Supply only integral water proofing compound.

S&F for 4mm thick decorative pre -painted non asbestos board (E-Board) in false ceiling with galvanised iron powder coated snap grid frame work in flat or in sloping of grid size 600mm x 600mm comprising of wall/cleat angle of size 25mm x 25mm x 0.35mm and cross tee of size 24mm x 38mm x 0.70mm with 4mm dia GI wire as suspender and including fixing arrangement from steel/wooden truss of any type including complete all as specified and directed.

M&L for factory made machine pressed precast concrete interlocking paver block any shape and size confirming to IS 15658-2006 of 60 mm thickness, M-35 Grade with grey cement & pigment over 25mm thick sand cushion layer complete all as specified.

M&L for 75 mm thick cement concrete 1:4:8, type D-2 using 40 mm graded crushed stone aggregate as in floor, sub base etc complete all as specified.

S&F for solid PVC wall lining consisting of 5mm thick wood grain printed PVC sheet inclusive of solvent cement and fixing at site on PVC frame as per specifications and drawing including PVC sheet filletts of width 35mm thick for wall paneling inclusive of fixing on wall to make PVC frame as per specifications and drawing complete all as specified.

S&F for steel work in tubular (square/rectangular hollow section) trusses including special shaped washer etc complete using ERW or induction butt welded tubes conforming to I S:1161-1979 grade St.-240 upto 10mtr height structure complete all as specified.

S&F for rolled mild steel sections as in main and cross beams, hip and jack rafters; purlins where connected to common rafters and running rails and guides for sliding doors; fixed with angle cleats or other connecting plate conforming to Fe 410 -W (GdeE- 250) quality-A complete all as specified.

S&F for pre- painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified.

S&F for anodised aluminium snap grid frame work size of grid 605mm x 605mm in false ceiling indluding necessary fixtures complete all as specified.

S&F for 12mm thick perforated particle board/ tiles for insulation and accoustic purposes of size 60cm x 60 cm fixed with screws to aluminium frame work on snap grid in flat or sloping false ceiling complete all as specified.

Demolition of cement concrete in ground floors and pavings n exc 15 cm thickness (below or above ground level) and removing the debris from site to outside MoD land.

M&L for preparation of newly plastered surfaces of walls and applying two coats of exterior emulsion paint over a coat of wall primer complete all as specified and directed by Engineer - in- charge.

M&L for preparation of newly plastered or unplastered surfaces and applying two coats of distemper oil emulsion on walls over a coat of wall primer complete all as specified and as directed.

M&L for powder coated anodised aluminium (minimum thickness of powder coating 50 micron) frame for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc. complete all as specified

S&F for powder coated anodised aluminium (minimum thickness of powder coating 50 micron) window and ventilator shutters, sliding type , aluminium section weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws etc. complete all as specified

S&F for powder coated anodised aluminium (minimum thickness of powder coating 50 micron) door shutters, aluminium section weighing 0.55 kg/ m including necessary joining cleats, glazing clips, ruber neoprene packing, handles 2 Nos in each door, hinges, anodised aluminum snap beading screws etc. complete all as specified

S&F for mild steel mortice lock, vertical type, size 100 mm.

S&F for double action floor spring hydraulically regulated made up of minimum 1.25 mm thick aluminium alloy sheet foundation box, main body with stainless steel cover, governing pivot made of brass, other parts made of mild steel heavy duty and fixed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) including removing the debris from site to outside MoD land complete.

M&L for Glazed colour ceramic tiles first quality of size 350x 250x 7 mm/ 450X 350X 7mm thick, set and jointed in neat cement slurry and pointed in colour cement to match including 10 mm thick rendering in CM 1: 4 as on vertical surfaces such as skirting, dado,wall etc complete all as specified.

M&L for Non skid coloured ceramic tiles,first quality, 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm, in floors etc. set and jointed in neat cement slurry and pointed in coloured cement to match including 15 mm thick screed bed in CM 1:6 complete all as specified.

M&L for complete removal of existing treatment of old decorated external surface of walls by electrically operated grinder including necessary scaffolding etc and applying two coats of exterior emulsion paint over a coat of wall primer of same brand/make complete all as specified and directed by Engineer - in- charge.

M&L for preparation of old treated plastered surfaces of wallls and applying two coats of distemper oil emulsion includingcomplete all as specified.

S&F for solid PVC door frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, suppling & fixing in opening as per specification & drawing

S&F for factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of MS tube for top and bottom rails. MS frame shall be covered with heat moulded plain colour PVC `C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheet for top rail, lock rail and bottom rail on either side and as gap insert for top rail and bottom rail, Pa+nelling of plain colour PVC sheet to be fitted in the MS frame welded/sealed to the stliles and rails with suitable PVC sheet beading, and jointed together with solvent cement, supplying & fixing in the frame at site as per specification and drawing.

S&F for butt hinges 100mm extruded aluminium alloy with galvanised mild steel hinge pin, anodised and fixed, type C-21.

S&F for 150 mm long aluminium anodized barrel tower bolt of extruded section complete.

S&F for 150mm long aluminium anodised handles, cast type complete.

S&F for 15mm bore galvanised steel water tubing, ‘Medium Grade’ with all fittings and fixed on walls, ceiling or laid in floors complete all as specified.

S&F for 15mm dia bib tap,chromium plated, fancy type screwed down high pressure for iron pipe and fixed complete.

S&F for CP Soap dish of Make : Jaquar Cat Pt No : AKP-35731P or its equivalent in Kohler/Marc.

S&F for CP towel ring of Make : Jaquar Cat Pt No : AKN-1121BN or its equivalent in Kohler/Marc.

S&F for 15 mm two in one angle valve, chromium plated, fancy type with high pressure screwed down complete all as specified.

S&F for vitreous china wash down water closet pan (pedestal pattern) white including trap and connection to drain (or outgoing pipe) and to fushing pipe, antisyphonage pipe etc complete.

S&F for 15mm dia Pillar taps, cast copper alloy, with capstan heads, chromium plated, fancy type, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, screwed for iron pipe and fixed .

S&F for 15 mm angle valve, chromium plated with wall flange, fancy type with high pressure screwed down and with CP flange of same make complete all as specified.

S&F for health faucet with double lock 1 meter brass plated stainless steel flexible hose and wall hook complete all as specified and directed Cat Part No.563 of make Jaquar or its equivalent in kohler/ Marc.

S&F for toilet paper holder with flat recessed type stainless steel complete all as specified.

S&F for PVC connections 15mm size with PTMT nuts of length 600 mm as specified.

S&F for plastic water closet seat cover, white, closed pattern with flat bottom and cover and mild steel chromium plated or aluminised hinging device complete.

S&F for PVC valveless, syphonic action type, flushing cistern low level, 10 litre capacity , white, with inlet, ball valve, float and handle including brackets complete .

S&F for wash hand basins vitreous china flat back 450mmx300mm size white, first quality, with and including chromium plated waste coupling 32mm size, PVC waste pipe 25mm bore heavy duty, china and plug and porcelain stopper, brackets of Mild Steel angle iron (35mmx35mmx5mm) of suitable size including two coat of synthetic enamel paint over a coat of primer complete to walls all specified.

S&F for 500 ltrs capacity rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top), three layers, hoisted and fixed in position all as specified in SSR Part-I and necessary GI nipple, union etc complete.

S&F for 20mm bore Ball valves high pressure of PTMT with epoxy coated aluminium rod & highdensity plastic ball screwed for iron pipe and fixed. (Minimum weight 15mm-142gms/ 20mm-210gms./ 25mm-455gms/ 40mm - 690 gms).

S&F for 110 mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls including suitable clamps after every one meter of interval complete.

S&F for 75 mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls including suitable clamps after every one meter of interval complete.

S&F for 110mm bore PVC (SWR) junction single, (Single T) equal or unequal complete.

S&F for 75mm bore PVC (SWR) junction single, (Single T) equal or unequal complete.

S&F for 110mm bore PVC(SWR) bends any radius with oval access door.

S&F for 75mm bore PVC(SWR) bends any radius with oval access door.

S&F for 20mm dia gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron/CPVC/ pipe and fixed

S&F for sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60cm long complete all as specified.

S&F for vitreous china urinals, full stall type (back or corner wall type) including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement; fixing automatic flushing cistern with brackets, flush pipe, grating and Union for discharge pipe. (Exclusive of fixing supply pipe to flushing cistern complete all as specified and directed.

S&F for 20mm dia tubular towel rail 600mm long of cast copper alloy, chromium plated with end brackets complete all as specified.

E/M Portion M&L for sand cushioning to under ground cable provided with layer of sand (8cm deep before laying the cable and 15 cm deep after laying the cable ie total 23 cm) complete all as specified.

M&L for brick of burnt clay sub class ‘B’ laid in trenches for cable protection laid dry flat all as specified.

Supply, laying & testing for cable XLPE insulated, screened PVC bedded galvanised steel strip or wire armoured, electric power cables (heavy duty) with alimunium conductor, 1100 volts grade, cross sectional area 35 sqmm 3.5 core all as specified.

S&F for galvanised steel tubing, light grade, 40 mm bore, laid in trenches or fixed to wall/pole with fitting as required for cable protection complete all as specified.

S&F for vertical type load line distribution board, double door, 4 way, IP 43 IK09 AC, 3 phase, 415 volts, TPN bus bar 250 Amps rating and earth bar & din rail.

S&F for MCCB, 4 pole 100 A, 16KA, 415Volts all as specified.

S&F for 240V, 10 KA 'B' curve miniature circuit breaker (MCB) of single pole and current carrying capacity 5 to 32 AMP with connection testing complete all as specified.

M&L for earthing complete with galvanised steel earth plate electrode 600mm × 600mm × 600 mm thick, buried directly in ground (earth pit not less than 2.25 metres deep below ground level) with top edge of the plate not less'than 1.5 metres below normal ground level, connected to galvanised earth lead wire 4.0 mm dia by means of bolts, nuts, check nuts and washers of galvanised iron or steel all as shown in Electrical plate No. 3 connected to earthing test point all as specified.

M&L for point wiring for following with single core PVC insulated unsheathed 1100 volt grade cable with multi stranded copper conductor of size 1.5 Sq mm FRLS (Nominal area) drawn through and including non metallic rigid PVC concealed conduit, medium grade, ISI marked not less than 20mm dia, concealed in wall, ceiling with GI saddles GI screws, rawl plugs (concealed conduit wiring) with all fittings including Tee, Junction boxes and modular metal flush boxes alongwith outer cover plate for mounting modular switch, socket and electronic regulator and drawing continuous earth wire with and including PVC insulated unsheathed 1100 Volts grade cable with stranded copper conductor of size 1.5 Sq mm FRLS (Nominal area) for one light point controlled by one switch one way complete all as specified.

All as per item No 121 above but for one fan/exhaust fan point controlled by one switch.

All as per item No 121 above but for one light point controlled by two 2-ways switches with cables 1.5 Sqmm.

All as per item No 121 above but for one 3 pin 5 Amp socket out let point on the same board controlled by one switch.

All as per item No 121 above but for one 3 pin 5 Amp socket out let point on the independent board controlled by one switch.

All as per item No 121 above but for one power point 6 pin 15 Amps socket out let with 2.5 Sq mm stranded copper conductor cable PVC insulated including earth wire 1.5 Sq mm copper conductor cable connected to earth dolly complete all as specified.

S&F for lamp holder, PVC/polycarbonate type, insulated body with back plate of batten fitting complete all as specified.

S&F for stepped type modular fan regulator 120 watt, 230 volts, 50 HZ, AC supply complete all as specified.

S&F for switch modular single pole one way 6 Amp 240 Volt,1 module complete all as specified.

S&F for switch of modular single pole one way 16 Amp 240 Volt, 1 moduls,complete all as specified.

S&F for modular socket, 6 amps 2/3 pine, 2 moduls, complete all as specified.

S&F for Modular switch 2 way 6A,1 module complete all as specified.

S&F for modular socket, 6/16 amps 2/3 pine, 2 moduls, complete all as specified.

S&F for Modular white cover plate with frame, 1 module, complete all as specified.

S&F for Modular white cover plate with frame, 3 module, complete all as specified.

S&F for Modular white cover plate with frame, 6 module, complete all as specified.

S&F for Modular white cover plate with frame, 8 module, complete all as specified.

S&F for Modular metal flush box, but 1/2,3 module, complete all as specified.

S&F for Modular metal flush box, but 6 & 8 module, complete all as specified.

S&F for ceiling rose, surface type, 65mm x 50mm, 2 to 3 terminal complete all as specified.

S&F for Indoor Elegant and sleek designed LED T5 , 20 Watt PC hosing LED with integrated batten 20 watt 4 feet white fixture complete with all accessories internally pre wired and including connecting up with twin core copper conductor cable complete .

S&F for Indoor Elegant and sleek designed LED T5 Battens, 10 W PC hosing LED with integrated batten 10 watt 2 feet white fixture complete with all accessories internally pre wired and including connecting up with twin core copper conductor cable complete. Make: C &S Cat Pt No LTTB2F10WLEDEW BATTEN or its equivalent in Wipro/Philips/Havels.

S&F of LED bldg light 45 watt IP66 with internally prewired including electronic driver and connecting up with three core flexible copper conductor 1.5 sqmm cable complete all as specified and directed Engr-in-Charge. Make:Havells Cat No. ENDURPEARLNEOSL45WLED757SASYTOPC or its equivalent in /C &S/ philips / wipro.

M&L for GI pipe medium grade 40mm dia bracket not less than 1.5 Mtr long and bend to a shape for fixing of bldg security light including 02 nos clamps made out of 25 x6 mm MS flat including 04 nos fully threated bolts and nuts fixing on wall etc., complete all as specified.

S&F for exhaust fan made of sturdy Engineering plastic complete with louvers shutter, voltage 230V, 50 Hz, RPM 1200, Copper winding of sweep 250 mm ,pre wired with 1.5 Sqmm flexible three core copper cable from connector to ceiling rose complete all as specified.

S&F for ceiling fans complete with blades, down rods, electronic regulator and accessories, 230 V, 1200 mm sweep Min air delivery 210 CFM with service value 6.00 BEE Five star rated with brushless direct current motor (BLDC) complete all as specified.

Shiv Shankar Nirman Co.

HANUMAN BUILDERS