SPECIAL REPAIR TO ROOF TREATMENT, TILING, JOINERY, SANITARY FITTINGS, etc INCLUDING INTERNAL ELCTRIFICATION FOR BLDG NO P-04 (01 TO 04 QTRs), NP-3 UNDER GE (NORTH) MAMUN AT MAMUN MIL STATION

Amount

Taking down chowkhats or frames of any description not exc 1.50 Sqm each with shutters, (without taking off shutters from the frame) including builders hardware , complete all as specified and directed.

Taking down chowkhats or frames of any description exc. 1.50 Sqm and n.exc 4.00 Sqm each with shutters, (without taking off shutters from the frame) including builders hardware complete all as specified and directed.

Taking down Shutters of any description exc 1 sqm and n exc 2 sqm each including builders hardware complete all as specified and directed.

M&L for pressed steel frames 125mmx60mm for door, made out of 1.25 mm thick MS sheet with one or more rebates including necessary fixing lugs, hinges, lock strike plate and back filling for chowkats in PCC (1:3:6) type C-0 (using 12.5mm graded crushed stone aggregate) tarring ends incl 02 coats of synthetic enamel paint over a coat of red oxide primer on exposed surface complete all as specified and directed.

M&L for pressed steel frames 105mmx60mm for door, made out of 1.25 mm thick MS sheet with one or more rebates including necessary fixing lugs, hinges, lock strike plate and back filling for chowkats in PCC (1:3:6) type C-0 (using 12.5mm graded crushed stone aggregate) tarring ends incl 02 coats of synthetic enamel paint over a coat of red oxide primer on exposed surface complete all as specified and directed.

M&L for pressed steel frames 75mmx50mm for door, made out of 1.25 mm thick MS sheet with one or more rebates including necessary fixing lugs, hinges, lock strike plate and back filling for chowkats in PCC (1:3:6) type C-0 (using 12.5mm graded crushed stone aggregate) tarring ends incl 02 coats of synthetic enamel paint over a coat of red oxide primer on exposed surface complete all as specified and directed.

M&L for 35mm thick, 2nd class hard wood plain framed, panelled (factory made) shutters (two panels) with lock rail and panel of 9mm thick BWP commercial ply or 12mm veneered particle board with commercial veneering on both faceS ,The size of rail and stile as per IS-1003 (Part-I) (Larger size to be provided) kiln seasoned and chemically pressure treated, fitted to chowkhats incl 02 coats of synthetic enamel paint over a coat of pink primer after preparation of surfaces complete all as specified and directed.

M&L for 35mm thick glazed and skeleton shutters (Factory made) of 2nd class hard wood and prepared to receive glass or gauge etc with rounded, chamfered or mitred sash bars edges of framing plain chamfered or rounded fitted with cut and mitred beads and fitted to chowkats for securing glass/gauge, size of stiles rails and other parts as per clause 8.20 (a) of SSR Part-I 2009 (Larger size to be provided) incl 02 coats of synthetic enamel paint over a coat of pink primer after preparation of surfaces complete all as specified and directed.

M & L for Solid PVC Door Frame of size 50mm x 47mm made out of 5mm wood grain pre-painted PVC sheet reinforced with M.S. Square tube, suppling & fixing in opening as per specification & drawing complete all as specified and directed.

M&L for 18 to 20mm thick prelaminated PVC solid board (one side decorative choice laminate and other side balancing white) as in kitchen cabinet, cupboard and pelmet box fixed with screws to PVC/timber frame work complete all as specified and directed.

M&L for Box type Steel windows and ventilators comprised of tubular frame and shutters made out of 1.25mm thick M S sheet tube factory made with double side hung wire gauged shutter & glass/glazed shutter (wire cloth and glass panes only shall be measured and paid separately) with steel handle and steel peg stay dovetailed or welded incl 2 Nos. tower bolts 150mm long for each leaf and 10mm square bar grills at spacing as shown on drg, welded to F I frame work, including other fittings; hinges, handles, tarred hold fasts fixed in PCC blocks all as shown on drg No CEPZ/TD-354/09 sheet 1/3 to 3/3 including two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed.

M&L for 30 mm thick (style) Factory made solid panel PVC door shutter consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification & drawing, as per specification & drawing panel, complete all as specified and directed. Make : Polycon, Echon industries, Rajshree plastiwood, HR Enterprises

S&F Stainless steel wire cloth 0.36 mm nominal dia of wire and average width of aperture 1.40 mm fixed with tinned tacks, orstainless steel wire staples complete all as specified and directed.

M&L for Hacking out old broken glass (any thickness, size, quality or description) from metal frame including punching or drilling out old glazing pins/spring clips complete all as specified and directed.

M&L for 3mm thick sheet glass ordinary quality and glazing with oil putty or fixed with beads/ glazing pins not .exc 0.5sqm in each pane complete all as specified and directed.

M&L for 3 mm thick Figured glass, pin head type & glazing with oil putty in squares n exc 0.5 sq.m in each panecomplete all as specified and directed.

M&L for repair to old steel window shutter not exc 1 Sqm including replacement of hinges, Handle and necessaery welding to shutter & chowkhat for making window in serviceable condition and including of painting of old window complete all as specified and directed.

M&L for stainless steel Butt hinges of size 100 mm fixed with steel screws of appropriate size complete all as specified and directed.

M&L for 250 mm long aluminium sliding door bolt with hasp & staple (bolt type) and fixing clip of sheets cast or extruded section and fixing sliding bolt of extruded section etc complete all as specified and directed.

M&L for 300mm aluminium sliding door bolt with hasp & staple (bolt type) and fixing clip of sheets cast or extruded section and fixing sliding bolt of extruded section etc complete all as specified and directed.

M&L for aluminium anodized barrel tower bolts 200 mm of extruded section and fixed. complete all as specified and directed.

M&L for Aluminium anodised handle, extruded section of size 150mm etc complete all as specified and directed.

M&L for 300 mm MS Rat tail door spring for door closer, complete all as specified and directed.

S&F Hasp and staple aluminium anodized 100mm long including bolt to hinge plate and fixed with screws, complete all as specified and directed.

S&F 2nd class hard wood small fitting such as brackets of any type, latch & hinge blocks, shaped door & window stops & the like including all necessary labours; articles n exc 200cu.cm each complete all as specified and directed.

S&F Peg set of Six powder coated fixed with chromium plated brass screws and wooden and plastic cleats (min wt 190gm) complete all as specified and directed.

S&F in repair for 25mm bore Mild steel powder coated, single curtain rod (wall thickness not less than 1mm) including fancy type PVC brackets of approved design/pattern, funnels etc suitable for single curtain rod complete all as specified and directed.

Dismantling of brick work or stone/ boulder masonry, built in cement mortar or cement lime mortar including all quoins, arches, pillars, etc and removal of rubbish out off the premises complete all as specified and directed.

M&L for Brick work with Fly Ash Brick (Non-Modular) straight or curved on plan to any radius in half brick thick walls built in (1:4) etc complete all as specified and directed.

M&L for Brick work with Fly Ash Brick (Non-Modular) Class 7.5, straight or curved on plan exceeding 6m mean radius built in CM (1:6) incl complete all as specified and directed.

M&L for brick work (except bricks) straight or curved on plan exc 6m mean radius built in (1:6) etc complete all as specified and directed. (Note : Serviceable bricks retrieved from dismantling shall be reused in this work/item)

M&L for preparation of newly /old plastered surface and apply two coat of exterior acrylic weather proof antifungal emulsion paint of approved brand and shade over and including a coat of primer as per manufacture instructions on external wall surface all as per manufacturers instructions complete all as specified and directed.

M&L for preparation of old plastered surfaces of ceiling and apply two coats of white wash on plastered surfaces complete all as specified and directed.

M&L for preparation of new plastered surfaces of ceiling and apply three coats of white wash on plastered surfaces complete all as specified and directed.

M&L for preparation of new plastered surfaces of wall & applying two coats of oil emlusion distemper over and including a coat of primer as per manufacture instructions over and including a coat of 2mm thick wall care putty & making the surface smooth complete all as specified and directed.

M&L for preparation of old plastered surfaces of wall including removal of existing treatment & applying two coats of oil emlusion distemper over and including a coat of primer as per manufacture instructions over and including a coat a coat of 2mm thick wall care putty & making the surface smooth including removal of existed treatment complete all as specified and directed.

M&L for preparation of old plastered surfaces of wall including removal of existing treatment and apply two coats of white wash on plastered surfaces complete all as specified and directed.

M&L for preparation of old plastered surfaces of wall including removal of existing treatment and apply two coats of cement based paint over a coat of alakli resistance priming paint complete all as specified and directed.

M&L for preparation of new plastered surfaces of wall and apply three coats of white wash on plastered surfaces complete all as specified and directed.

Demolition of cement concrete (unreinforced) in ground floors & paving not exceeding 15 Cms thickness (beloe or above ground level ) complete all as specified and directed.

M&L for PCC (1:2:4) type B-1 (using 20mm graded crushed stone aggregate) as in surface channels and drains complete all as specified and directed.

M&L for Extra for forming fair finished drain or channel 30 cm inner girth in cement concrete, using ex- tra cement, including forms, moulds, mi- tred/stopped ends complete all as specified and directed.

M&L for GI wire netting 0.90mm dia and 12mm mesh lathing to wood or metal studding, joists, etc. in walls, ceilings, stanchions, beams, etc. including all laps, cutting and waste complete all as specified and directed.

M&L for 75mm thick PCC (1:3:6) type C-1 (using 20mm graded crushed stone aggregate) as in plinth protection laid in panels and joints filled with mix of bitumen 85/25 grade and sand (1:2) by weight, finished the surface even and smooth using extra cement complete all as specified and directed.

S&F in repair 15mm bore Stop valves Stop valves, cast copper alloy,screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed complete all as specified and directed. Make : Jaquar / Hindware /Marc.

S&F in repair 15mm bore Stop valves fancy type, chromium plated cast copper alloy long shank and exposed part kit with fitting sleeve, operarting lever & adjustable wall flange (concealed type) screwed both ends for iron pipe or for unions complete all as specified and directed. Make : Jaquar Cat part No CON-083FT & CON-083FTK or equivalent of Hindware/Marc.

S&F in repair for single towel rail brass chromium plated 600mm long fixed with chromium plated screw and PVC cleat complete all as specified and directed. Make : Cat part No AQN-7711 of Jaquar or equivalent model in Hindware/Marc.

S&F in repair Brass Chromium Plated shower rose with arms fancy type with swivel joints 75 mm face dia of appoved make and cat part for 15mm bore iron pipes complete all as specified and directed. Make : Prayag Cat part No BS-73 or equivalent model in Hindware/Marc.

S&F S & F Continuous (piano) hinges,(Width of flaps in 30mm (when open) , mild steel, bright finish or electrogalvanised complete all as specified and directed.

M&L for Vitreous china wash hand basin, white, flat back, size 550x400mm (Make : Jaquar Cat part No CNS-WHT-801 or equivalent model in Hindware/Parryware/Somany) including brackets, CP waste coupling, 32mm bore PVC waste pipe of min 600mm long & 15 mm bore PVC connections, including cutting for and pinning in end of brackets or erecting stand fixed in repairs complete all as specified and directed.

S&F in repair for 15mm bore Pillar taps (ISI marked), cast copper alloy, with capstan heads, chromium plated fancy type, screw down high pressure with or without latters hot or cold with long screwed shank and fly nuts screwed for iron pipe complete all as specified and directed. Make : Jaquar Cat part No FLR-5011N or equivalent model in Hindware/Marc.

S&F in repair for 15mm bore bib taps fancy type with wall flange, chromium plated cast copper alloy long body with capstan heads, screwed for iron pipe or brass ferrule complete all as specified and directed.

Taking up or down 15mm bore pipe and connections including cleaning for refixing including all new fittings for 15mm bore complete all as specified & as directed.

Taking up or down 20mm bore pipe and connections including cleaning for refixing including all new fittings for 20mm bore complete all as specified & as directed.

M&L for GI water tubing surface/concealed, 15mm bore, medium grade galvanized with all fittings (such as tee, elbow, socket, union, short pieces) and application of bituminous paint on concealed portion of tubing, fixed to wall or ceiling or laid in floor, complete all as specified and directed. (Note : Cutting chases and making good shall be measured and paid separately)

Refixing of old steel tubing 15mm bore, medium grade galvanized with all fittings (such as tee, elbow, socket, union, short pieces) fixed to wall , floor etc complete all as specified and directed. (Note : Cutting chases and making good shall be measured and paid separately)

Cutting chases, pinning in. making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc and cutting chases for concealed water tubing or concealed conduit wiring, etc, and making good, cutting not exc 10 cm girth complete all as specified & directed.

M&L for GI water tubing surface/concealed, 20mm bore, medium grade galvanized with all fittings (such as tee, elbow, socket, union, short pieces) and application of bituminous paint on concealed portion of tubing, fixed to wall or ceiling or laid in floor, complete all as specified and directed. (Note : Cutting chases and making good shall be measured and paid separately)

Refixing of old steel tubing 20 mm bore, medium grade galvanized with all fittings (such as tee, elbow, socket, union, short pieces) fixed to wall , floor etc complete all as specified and directed. (Note : Cutting chases and making good shall be measured and paid separately)

Taking down cement plaster on brick or stone walls,etc including racking out joints , hacjking for keys,scrubing down with water etc, and removal of rubbish out off the permises complete all as specified.

M&L for rendering 10mm thick on fair faces of brick work or concrete surface in CM (1:6) on wall surfaces finished even and smooth without using extra cement complete all as specified & directed.

M&L for rendering 5mm thick on brick work or concrete surface in CM (1:3) on ceiling surfaces finished even and smooth without using extra cement complete all as specified & directed.

M&L for Rendering 15mm thick in two layers [base layer 10mm IN CM 1:6 & finishing layer 5mm thick in cement mortar (1:4)] using liquid water proofing compound in IInd layer only on brick work or concrete surfaces of wall, surfaces finished even and smooth using extra cement complete all as specified & directed. (Note : WPC shall be measured and paid separately)

M&L for rendering or plastering work 10mm thick in CM (1:3) in fascia / edging / ceiling of Chajjas, roof projections and making the line in true shape and finishing the surface without using extra cement including taking off peeled plaster complete all as specified and directed

M&L for preparation of newly plastered surfaces of wall & making the surface smooth with and paper and priming surface including applying two coats of cement base paint over a coat of alkali resistance primer paint as per manufacturer instructions complete all as specified and directed.

M&L for PCC (1:2:4) type B-0 (using 12.5mm graded crushed stone aggregate) as in coping, in lintels upto 1.5m clear span, cills, steps; seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings upto 60 cm in height,copings, kneelers, apex stones, bed plates, water troughs and the like including weathering, slightly rounded or chamfered angles and throating, as directed finished the surface even and smooth without using extra cement etc complete all as specified and directed.

M&L for 25 mm thick floor in PCC 1:2:4 type B-1 (20mm graded crushed aggregate) as in sub base of floor, complete all as specified and directed.

M&L for vitrified tiles (Industrial grade) matt finish thickness 10 mm floor tile of size area exc 0.36 Sqm and not exc 0.42 Sqm as in floor, set and jointed in neat cement slurry and pointed in coloured epoxy grout to match laid over and including 15mm thick screed bed as in 1:4 (surface finished even and rough to receieve tiles complete all as specified and directed by Engr-in-Charge.

M&L for Industrial grade (Industrial grade) matt finish thickness 10 mm as in skirting / dado of size area not exc 0.36 Sqm, set and jointed in neat cement slurry and pointed in coloured epoxy grout to match laid over and including 10 mm thick backing coat in 1:3(surface finished even and rough to receieve tiles including taking out of tiles/ plaster and removal of rubbish out off the premises complete all as specified and directed.

M&L for Industrial grade (Industrial grade) matt finish thickness 10 mm as in skirting / dado of size area exc 0.36 Sqm and n exc 0.42 Sqm, set and jointed in neat cement slurry and pointed in coloured epoxy grout to match laid over and including 10 mm thick backing coat in 1:4 complete all as specified and directed.

M&L for Non-skid ceramic coloured rectified edges tiles (joint free) 8mm thick area of each tile exceeding 0.11 Sqm but not exceeding 0.18 Sqm in floors etc, set & jointed in neat cement slurry and pointed in coloured epoxy grout to match laid over and including 15mm thick screed bed or bedding layer of cement mortar (1:4) complete all as specified and directed.

M&L for Non-skid ceramic coloured rectified edges tiles (joint free) 8mm thick area of each tile exceeding 0.11 Sqm but not exceeding 0.18 Sqm in skirting/dado/riser of steps etc, set & jointed in neat cement slurry and pointed in coloured epoxy grout to match laid over and including 10mm thick screed bed or bedding layer of cement mortar (1:4) complete all as specified and directed.

M&L for Glazed ceramic (coloured) tiles 7mm thick, of size 450mmx300mm on vertical surfaces such as dado etc, set and jointed in neat cement slurry and pointed in coloured epoxy grout to match tiles over and including 10mm thick backing coat in cement mortar (1:4), surface finished even and rough to receive tiles, including dismantling existing tiles of any type and pattern including cement mortar backing coat and removal of rubbish out off the premises complete all as specified and directed.

M&L for 20mm thick Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window- cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite including rounding & chamfering to the edges of granite not exceeding thickness 20mm thick , laid over and including 15mm thick screed bed in CM 1:4 including Roughening surfaces of old concrete floor by picking, sweeping clean and washing down with water to remove dust, etc & Brushing neat cement slurry with 3.0kg of cement per sq. metre including dismantling of existing tiles/stone etc complete all as specified and directed.

S&F for Vitreous china White Squatting Orissa Pattern pan (Make : Somany Cat part No 121115 or equivalent model in Hindware/Parryware) of size 580x440mm, including cast iron ‘P’ or ‘S’ trap, front or back inlet and integral foot rests and making connection to trap and to flushing pipe, anti syphonic pipe,including provision of PCC 1:5:10 type E-2 (using 40mm graded crushed stone aggregate) bedding including demolition complete all as specified and directed. (Note : Demolition and refilling of concrete in sunken portion is included in the Contractor quoted rate.)

S&F in repair for Vitreous china white wash down water closet pan (pedestal pattern) with normal closing seat cover S-trap (Make : Jaquar Cat part No CNS-WHT-553SN or equivalent Cat Part/Model of Hindware/Parryware/ Somany) & hand shower (Health foucet) 8mm dia 1.5m long flex tube in chrome finish and wall hook with NRV (Back flow preventer) and connection to drain (or out going pipe) (Make : Jaquar Cat Part No ALD-563 or equivalent Cat Part/Model of Hindware/Parryware) and to flush pipe, antisyphonic pipe etc complete all as specified and directed

M&L for Rendering 15 mm thick on brick work or concrete surfaces in CM 1:4 with and including water proofing compound to sunken portion with proper slope towards outside and finishing cement concrete surface even and smooth using extra cement including application of 90 micron polythene film and applying bitumen coating @ 3.00 Kg/Sqm etc complete all as specified and directed. [Note : WPC shall be measured and paid seperately]

M&L for as in repair of Brass CP suitable for centre hole basis mixer for mixing hot & cold water screwed down for 15mm bore dia of pipe & 450mm long iron pipe and fixed cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, screwed for iron pipe and fixed complete all as specified and directed. Make : Jaguar/Marc/Johnson

M&L for as in repair wall mixer with over head Brass chromium plated shower rose 125mm size Brass CP mixer for mixing hot & cold water screwed down for iron pipe of size 15 mm bore pipe with or without swivel joints, any size, including fixing to steel pipe or union. Make : Jaguar/Marc/Johnson

S&F in repair for PVC flushing cistern dual flush type 10 Ltr capacity, valve-less syphonic action type, low level, complete with inlet, ball valve, handle, including brackets/pins, PVC flush pipe 32mm bore complete all as specified and directed.

S&F in repair for PVC connection 15mm size with PTMT nuts of length 450mm long of appoved make complete all as specified and directed.

S&F in repair for Rotational moulded polyethylene water storage tanks three layer of capacity 1000 litre, (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part I including 20mm ball valve high pressure of PTMT with epoxy coated Aluminum rod & high-density plastic ball and dismantling of existing PVC tank of any capacity, complete all as specified & directed.

S&F in repair for Rotational moulded polyethylene water storage tanks three layer of capacity 500 litre, (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part I including 20mm ball valve high pressure of PTMT with epoxy coated Aluminum rod & high-density plastic ball and dismantling of existing PVC tank of any capacity, complete all as specified & directed.

S&F in repair 20mm bore gun metal gate valve, with cast iron wheel head, screwed both ends for GI pipe and fixed cast copper chromium plated fancy type alloy ISI marked with crutch or butterfly screwed down for GI pipe 20 mm dia complete all as specified and directed.

S&F in repair for Stainless steel sink with draining board 1mm thick sheet for kitchen with plugs, washers and wastes; including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 915mm x 460mm and bowl size 410mm x 330mm x 160mm, including 32mm bore PVC waste outlet pipe of minimum length 600mm complete all as specified and directed. Make : Blue star Cat part No. BSSBSD-52 or equivalent model in Nirali/Jyoti

S&F Stainless steel plate rack of size 750mmx900mm fixed with chromium plated screw and PVC cleat complete all as specified and directed. Make : Blue star Cat part No. KPR-312 or equivalent model in Nirali /Jyoti

S&F in repair for 100 mm bore, sand cast, cast iron soil, waste and vent pipe with cement joints, in any length with ears, laid in floor with or without cement joints complete all as specified and directed.

S&F in repair for 100 mm bore, sand cast, cast iron soil, waste and vent pipe with cement joints, in any length with ears, fixed to wall with and including in stack clamp made out of 50mm x 6mm galvanised flat iron fixed with bolt and nuts etc complete all as specified and directed.

S&F in repair for 100 mm bore, cast iron bends (any radius), diminishing pieces or tapers (large bore measured) without oval access door complete all as specified and directed.

S&F in repair for 100 mm bore, cast iron bends (any radius), diminishing pieces or tapers (large bore measured) with oval access door complete all as specified and directed.

S&F in repair 100 mm bore dia Cast Iron Branch peices, single(equal or unequal) ordinary or inverted (spigot or socket type), or with parrallel branches fitted with oval access complete , ISI Marked, complete all as specified and directed.

S&F in repair for 75 mm bore, sand cast, cast iron soil, waste and vent pipe with cement joints, in any length with ears, laid in floor with or without cement joints complete all as specified and directed.

S&F in repair for 75 mm bore, sand cast, cast iron soil, waste and vent pipe with cement joints, in any length with ears, fixed to wall with and including stack clamp made out of 50mm x 6mm galvanised flat iron fixed with bolt and nuts etc complete all as specified and directed.

S&F in repair for 50 mm bore, sand cast, cast iron soil, waste and vent pipe with cement joints, in any length with ears, fixed to wall with and including stack clamp made out of 50mm x 6mm galvanised flat iron fixed with bolt and nuts etc complete all as specified and directed.

S&F in repair for 75 mm bore, cast iron bends (any radius), diminishing pieces or tapers (large bore measured) without oval access door complete all as specified and directed.

S&F in repair for 75 mm bore, cast iron bends (any radius), diminishing pieces or tapers (large bore measured) with oval access door complete all as specified and directed.

S&F in repair 75 mm Cast iron cowl, fixed with cement joints complete all as specified and directed.

S&F in repair 50 mm Cast iron cowl, fixed with cement joints complete all as specified and directed.

S&F in repair for 75 mm Cast iron floor trap, with CP grating including jointing to waste pipe fixed in cement concrete type B-1 (1:2:4) (using 20mm graded crushed stone aggregate) complete all as specified and directed.

S&F in repair 75mm bore dia Cast Iron Branch peices, single(equal or unequal) ordinary or inverted (spigot or socket type), or with parrallel branches fitted with oval access doors of 75 mm bore dia complete ,( ISI Marked ) complete all as specified and directed.

Taking down eaves gutters and rainwater pipes (any size or pattern), including all fittings, heads, shoes, bends, swan-necks, etc., including cleaning or refixing or removal to Store (measured overall as fixed along the centre line over fittings and accessories) complete all as specified and directed.

S&F in repair for 110 mm PVC (SWR) pipes single socketed in any length with rubber joints including bends and necessary fittings fixed to walls complete all as specified and directed.

S&F as in repair for PVC (SWR) bends for 110 mm bore size pipe any radius complete all as specified and directed.

S&F as in repair for Salt-glazed stoneware gully traps, of size 150mmx100mm square or round mouthed, type 'P' complete all as specified and directed.

M&L for Rolled sections as in framing FOR COOLER STAND for cladding, glazing and the like fixed with angle cleats and connecting plates, etc conforming to Fe 410 -W (Gde- E- 250) quality - A, complete all as specified & directed.

Taking down brick tiles or terracing tiles, single layer from roof laid, bedded and pointed in any mortar complete all as specified and directed.

M&L for Cement concrete (1:2:4) type B-1 (using 20mm graded crushed stone aggregates) such as in benching, coping, Bed blocks , broken chajjas and the like, rounded or chamfered on edges including necessary formwork including demolition of existing concrete of any description and removal of debris out off the premises etc complete all as specified and directed.

M&L for PCC (1:2:4) type B-0 using (12.5 mm graded crushed stone aggregate) as leveling course/padding using water proofing compound laid over existing roof, surface finished rough to receive cement mortar including necessary formwork including demolition of existing concrete of any description and removal of debris out off the premises complete all as specified and directed. Note : (WPC shall measured and paid separately)

M&L for APP modified roof treatment over existing accessible RCC roof slab / chajjah / canopy / parapet wall to be executed through approved applicator of the membrane manufacturer with following specification incl. dismantling of old APP treatment complete all as directed :- (a) Cleaning existing surface properly. (b) Applying oil bound bitumen primer @ 0.30 liter/Sqm manufactured by the same agency as that of APP with a density 0.87-0.89 Kg per liter at 25 degree centigrade on prepared surface. (c) Laying not less than 3mm thick APP modified water proofing membrane weighing not less than 3.60 Kg/Sqm reinforced with non woven polyster fiber weight not less than 160gsm/Sqm using butane torch by torch application with 10cm side laps and 15cm end lap. Laying of membrane, Physical property of membrane shall be as under :- (i) Membrane weight not less than 3.60 Kg/Sqm. (ii) Non woven polyester weight not less than 160 gsm/Sqm. (iii) Softening point of membrane not less than 150 degree Celsius. (iv) Joint tensile strength-longitudinal not less than 650/Sqcm and transverse not less than 450/sqcm at 230 degree Celsius. (v) Tear strength - longitudinal not less than 300 N & transverse not less than 250N. (vi) Elongation of reinforcement not less than 30%. (vii) Impermeability under water pressure not less than 3 Kg/Sqcm. (d) APP membrane shall be laid using butane torch by Torch application with minimum 10cm side overlap and 15cm end lap.

M&L for APP modified roof treatment over existing non-accessible RCC roof slab / chajjah / canopy / parapet wall to be executed through approved applicator of the membrane manufacturer with following specification complete all as directed :- (a) Cleaning existing surface properly. (b) Applying oil bound bitumen primer @ 0.30 liter/Sqm manufactured by the same agency as that of APP with a density 0.87-0.89 Kg per liter at 25 degree centigrade on prepared surface. (c) Laying not less than 3mm thick APP modified water proofing membrane weighing not less than 3.60 Kg/Sqm reinforced with non woven polyster fiber weight not less than 160gsm/Sqm using butane torch by torch application with 10cm side laps and 15cm end lap. Laying of membrane, Physical property of membrane shall be as under :- (i) Membrane weight not less than 3.60 Kg/Sqm. (ii) Non woven polyester weight not less than 160 gsm/Sqm. (iii) Softening point of membrane not less than 150 degree Celsius. (iv) Joint tensile strength-longitudinal not less than 650/Sqcm and transverse not less than 450/sqcm at 230 degree Celsius. (v) Tear strength - longitudinal not less than 300 N & transverse not less than 250N. (vi) Elongation of reinforcement not less than 30%. (vii) Impermeability under water pressure not less than 3 Kg/Sqcm. (d) APP membrane shall be laid using butane torch by Torch application with minimum 10cm side overlap and 15cm end lap. (e) Top of membrane shall be provide with solar reflective bituminous aluminum paint @ 0.1 Kg/Sqm as prescribed by manufacture of membrane.

M&L for 20mm thick cement plaster in cement mortar 1:4 on concrete surface finished even and smooth using WPC liquid of make Dr.Fixit or STP as per manufacturer instruction @ 0.200 Ltr in 50 kg of cement, complete all as specified and directed.

M&L for 40mm thick fly ash brick tiles over torched APP membrane with joints grouted flush in cement mortar (1:3) mixed with 5% of crude oil by weight of cement over and including bedding layer of cement mortar 15mm thick in 1:4 using WPC etc complete all as specified and directed. (Note : WPC shall be measured and paid separately)

M&L for 40mm thick brick tiles (except brick tile) over torched APP membrane with joints grouted flush in cement mortar (1:3) mixed with 5% of crude oil by weight of cement over and including bedding layer of cement mortar 15mm thick in 1:4 using WPC complete all as specified and directed. (Note : 1. WPC shall be measured and paid separately. 2. Birck tile retrieved from dismentling to be reused in this work.)

Demolition of cement concrete (reinforced) of any description in any position not otherwise specifically provided for cement concrete (reinforcement cut as required to faciliate demolition) complete all as specified and directed.

M&L for RCC 1:1½:3 Type A-1 using 20mm graded crushed stone aggregate as in chajjas, facias including necessary formwork complete all as specified and directed. (Note: Reinforcement shall be measured and paid separately)

M&L for Mild steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

M&L for providing cement concrete (1:1.5:3) type A-1 (using 20mm graded crushed stone aggregate) in landings, cover slabs (for man holes etc) chullah hoods, chajjas, water troughs, mangers, shelves and similar articles with plain faces etc, set in cement morter (1:4) (of any section indicated) with plain fair faces, including chamfers, weatherings, throating etc and setting in mortar complete with joints to match complete all as specified & directed.

Supply only Polymer liquid water proofing compound of make Pidilite/Bauchemic/Fosrock, all as specified and directed.

M&L for Providing and injecting chemical emulsion for Post Constructional Antitermite Treatment Along the external wall below concrete or masonry apron using chemical emulsion @ 2.25 litres per linear metre including drilling and plugging holes etc. in apron/plinth protection complete all as specified as in conforming to IS 8944 - 2005 & directed.Note:- Chlorphyriphos 20% EC or Lindane 20% EC (ISI Marked) shall only be used .

M&L for Providing and injecting chemical emulsion for Post Constructional Antitermite Treatment of soil under existing floors using emulsion @ one litre per hole, 300mm apart including drilling and plugging 12mm dia holes with cement mortar 1:2 (1 cement: 2 coarse sand) to match the existing floors. complete all as specified as in conforming to IS 8944 - 2005 & directed.Note:- Chlorphyriphos 20% EC or Lindane 20% EC (ISI Marked) shall only be used .

Taking down carefully unserviciable/ damaged copper/aluminium surface (batten/coduit or casing caping) point wiring any length for light/fan/socket or power including unscrewing from board (fitting and fixture such as switches, sockets, ceiling rose, lamp holders, brackets, pendent, regulators, sockets, Bracket /sketch fitting etc ) and removing material from site and making good to the disturbed surface to match with existing finish complete all as specified and directed.

M&L for Modular Point wiring using FRLS PVC insulated unsheathed /multi stranded copper conductor cable 1.5 sqmm including 1.5 Sqmm FRLS PVC insulated unsheathed copper conductor earth wire drawn through and including concealed PVC conduit of appropriate size not less than 20 mm dia and 1.8 mm thick including all fittings viz tees, bends, junctions box and approved make sunken modular metal flush gang box and suitable support frame and cover plate (inner/outer) of required modules for mounting modular switches/ sockets etc, connecting earth including cutting groove for concealed wiring, making good to disturb surface of wall/floor with cement mortar and finishes to match existing including connection of cable with MCBs or bus bar shall be done through proper size copper/brass thimble of pin/u type etc (conduit shall be fixed on surface of ceiling with necessary saddles where concealing of conduit is not feasible), for light/fan/bell point complete all as specified and directed. (Note : Modular switch/bell push/fan regulator etc shall be measured and paid separately under respective items.)

All as per Srl item No. 123 above but for one light point controlled by two way switch, single pole, 5 Amp, 240 volts etc complete all as specified and directed.

All as per Srl item No. 123 above but for one multipin socket (5 pin) controlled by one switch, single pole, 5 Amp, 240 volts on the same board etc complete all as specified and directed.

All as per Srl item No. 123 above but for one multipin socket (5 pin) controlled by one switch, single pole, 5 Amp, 240 volts on independent board etc complete all as specified and directed.

M&L for Modular point wiring using FRLS PVC insulated unsheathed /multi stranded copper conductor cable 2.5 sqmm including 2.5 Sqmm FRLS PVC insulated unsheathed copper conductor earth wire drawn through and including concealed PVC conduit of appropriate size not less than 20 mm dia and 1.8 mm thick including all fittings viz tees, bends, junctions box and approved make sunken metal flush gang box and suitable support frame and cover plate (inner/outer) of required modules for mounting modular switches/ sockets etc, for one 6 pin socket outlet 15 amps, Modular multi purpose independent point controlled by 15 Amp switch Single pole , one way , 240 volts l connecting earth including cutting groove for concealed wiring, making good to disturb surface of wall/floor with cement mortar and finishes to match existing including connection of cable with MCBs or bus bar shall be done through proper size copper/brass thimble of pin/u type etc (conduit shall be fixed on surface of ceiling with necessary saddles where concealing of conduit is not feasible), for light/fan/bell point complete all as specified and directed. (Note : Modular switch/bell push/fan regulator etc shall be measured and paid separately under respective items.)

M&L for Sub main wiring with FRLS PVC insulated unsheathed 2X6 sqmm multistranded copper conductor cable 1100 V with 1X6 sqmm FRLS PVC insulated green multistranded copper cable for continuous earth drawn through & including concealed PVC conduit of appropriate size not less than 20 mm dia & 1.8mm wall thickness with all accessories including cutting grooves and making good disturbed surface to match existing including taking down existing surface sub main wiring complete all as specified and directed. (Note: Two runs of FRLS PVC cable with one run of earth conductor and conduit shall be measured as one RM.)

S & F modular switch piano type flush button one way, single pole 5 Amp one module complete all as specified and directed. Make : Legrand Cat Part No 673000/Crabtree Cat Part No ACMSXXW101/Anchor Roma Cat Part No 66111.

S&F Modular Socket outlet, 5 pin, multi purpose 2 module 6 Amps, AC 230 volts, etc complete all as specified and directed. Make : Crabtree (Verona) Cat Part No : ACVKSWW065 or equivalent of Legrand/Siemens/Schenider/Anchor Roma.

S&F modular switch Socket outlet, 2 in 1, 6 pin, ,5/15 Amps, flush type (ISI Marked ) AC 230 volts, etc complete all as specified and directed. Make : Crabtree /Legrand / Schneider /Siemens/Anchor Roma

S&F modular Switch piano flush button single pole one way 16 Amp (ISI Marked ) AC 230 volts, front opreated etc complete all as specified and directed. Make : Crabtree /Legrand / Schneider /Siemens/Anchor Roma

S&F modular Switch piano flush button single pole two way 6 Amp (ISI Marked ) AC 230 volts, one module etc complete all as specified and directed. Make : Crabtree /Legrand / Schneider /Siemens/Anchor Roma

S&F modular switch bell push flush 06 Amp (ISI marked) complete all as specified and directed. Make : Legrand / Anchor Roma / Schneider /Siemens/Crabtree

S&F door Bell Ding Dong AC 230 Volt, single Pole etc complete all as specified and directed. Make : Anchor Cat Part No 8024 or equivalent of Havells(Reo)/SSK (Topline)/GM (Vyoma)

S&F Ceiling rose polycarbonate isolated body surface Bakelite, not less than 65 x 50 mm, three terminals, AC 230 volts etc, complete all as specified and directed. Make : Havells Cat Part No Reo/Cona Cat Part No 9246/GM Cat Part No 8224

S &F in replacement the LED type 15 watt lamp , 230 volts retrofit suitable for any type lamp holder complete all as specified and directed.

S&F Lamp holder insulated body with back plate suitable for batten fitting including 12W LED lamp of approved make and cat part and PVC Round/Square block etc complete all as specifeid and directed.

S & F Fan regulator modular step type suitable for 1200/1400mm sweep ceiling fan hum free, 100W- 2 module including necessary connections complete all as specified and directed. Make : Legrand Cat Part No 673028/Crabtree Cat Part No ACARFHW005/Anchor Roma Cat Part No 66502.

S &F in replacement the Bulk head light fitting LED type 10 watt complete with 10 watt LED and having IP-66 protection and fixing on wall/ceiling complete with all accessories and including connecting up with ceiling rose with & including PVC insulated and overall sheathed flexible copper conductor cable and including 3 core 0.50 Sqmm complete all as specified and directed.

S &F as in replacement wall mounted type fancy light fittings suitable for retrofit LED Lamp B22 including 9 Watts LED bulb & with decorative diffuser and mounting clips & lamp holder including wall mounting arrangement ,230 volts complete with all accesories internally prewired and including connecting up with three core twisted flexible copper conductor cable of suitable size complete all as specified and directed.

S&F decorative wall mounting bed side light 3 watt fitting LED type having flexible neck complete all as specified and directed.

S &F building high performance LED security light luminaries 30 W LED, AC 230 volts, ( IP 66 Protection ) new generation saving & enviromental friendly long life versatile pressure die cast aluminium luminaries with high power LED as light source complete making connection with street light/ building security light box or OH line using PVC insulated and sheathed single core multi stranded copper conductor cable of size 1.5Sqmm including duly mounted on bracket of GI light grade pipe of dia 40mm bend to shape of overall length 1.5m with GI clamps of size 40mm x 6mm and fixing to wall by means of suitable size nuts & bolts complete all as specified and directed.

S &F as in repair high efficiency LED 1x 20 watts ,white powder coated CRCA Box type with decorative end cap of 4 feet length alongwith LED T-8 tubelor lamp 20W liner with extruded aluminium/ PC body, PC diffuser & in built driver energy efficient light fittings ,230 volts wall mounted complete with all accesories internally prewired and including connecting up with three core twisted flexible copper conductor cable of suitable size complete all as specified and directed.

S & F mirror light 1x10 watt LED type with all accessories including inbuilt lamp connecting electrically to ceiling rose using cord flexible 3core PVC insulated over all sheathed with flexible copper conductor of size 0.75 sqmm complete all as specified and directed. Notes for Srl Item Nos 140 to 145:- 1. Driver shall be potted antivibration type. 2. LM-79 and LM-80 test report with 1 Lakh burning hours LED life from NABL lab shall be povided. 3. CRI (Colour Rendring Index) of fixture shall be > 70. 4. CCT (Colout Correlated Temprature of fixture shall be 5700K ± 300 K. 5. System Lumen Efficacy shall be > 100Lm/W 6. 10 KV separate Surge Protection shall be provided as a part of fitting. 7. 5 years gurantee shall be provided by contractor suppoted by OEM covering all parts of luminaire. 8. Lenses shall be Modular Type. 9. PCB used shall be MC PCB type 10. The defect liability period of LED light shall be 05 years from the certified date of completion & the Contractor shall replace / repair the defective fitting within 07 Days after handing over to Contractor for replacement / repair 11. CA No shall be written on each fitting before installation. 12. The name of manufacturer to be embossed on the fitting. 13. The fittings shall have arrangement so that maintaince required, if any can be carried out from Top cover.

S&F for MCB single pole (SP) 240 volts, 6 to 32 Amps, 10KA (C-series) , complete all as specified and directed.

S&F for MCB single pole neutral (SPN) 240 volts, 40 to 63 Amps, 10KA (C-series) complete all as specified and directed.

M &L for Double door MCB DB SP, 240 Volts,200 Amps rated bus bar 08 Way made out of CRCA powder coated sheets, IP43 protection with copper bus bar with including taking out old unserviciable MCB DB any size/type, complete all as specified and directed.

S&F for MCB single pole (SP) 240 volts, 50 Hz 40 to 63 Amps,, 10KA (C-series) complete all as specified and directed.

Taking down ceiling fan of any sweep & size and refix in same position after overhauling including minor repairs by replacement of capacitor, safety pin, cap, nuts & bolts etc and making connection using 3 core, 0.50 Sqmm PVC insulated and overall sheathed flexible copper conductor cable from ceiling rose to fan, including testing to ensure efficient functioning including application of one coat of synthetic enamel paint by spray painting & rewriting number complete all as specified and directed.

S&F Venti Air Fan single phase, 230/240 Volts of size 300mm sweep with loure of metalic body with nut bolts and making the suitable hole for 300mm sweep exhaust fan by breaking the existing wall & making good the distrubed surface by the plastring and matching with existing surface /specification , complete all as specified and directed. Make : Crompton Greaves Trains Air Exhaust/ Bajaj Bahar 300mm/Havells Ventilair DXW6

S&F Double door distribution board (Sheet metal enclousers) iron clad made out of CRCA powder coated sheets with IP43 protection suitable for MCCB 3 pole, 415 volts , 100 Amps rated with rupturing capacity 16 KA as incomer & one MCB as outgoing ,415 volts , 3 phase 50 C/S , 4 way , with suitable copper bus bar, complete including cutting chases to walls for fixing DB & making good the disturbed wall surface all as per site requirement to match the existed finishes including taking out old unserviciable DB any size/type complete all as specified and directed.

S&F Sheet metal enclousers SPN (Distribution board) iron clad made out of CRCA powder coated sheets with IP43 protection with TWO PIN & EARTH PLUG AND SOCKET including one MCB 20 Amp, 240 volts complete including cutting chases to walls for fixing DB & making good the disturbed wall surface all as per site requirement to match the existed finishes including taking out old unserviciable DB any size/type complete all as specified and directed.

M&L for earthing complete with galvanised steel earth plate electrode, 600mm x 600mm x 6mm thick, buried directly in the ground (earth pit not less than 2.25m deep below normal (ground level) with top edge of the plate not less than 1.50m below ground level connected to galvanized iron wire 4mm dia as earth lead by means of bolts, nuts and washers of GI up to test point, HDPE pipe 15mm bore as protection pipe, GI watering pipe 20mm bore light grade with funnel and wire mesh, charcoal and salt, 40mm thick pre-cast RCC (1:2:4) type B-0 (Nominal mix) cover reinforced with XPM (weighing n.less than 4 Kg/Sqm) with suitable steel handle, and angle iron 40X40X3mm frame and chamber of PCC (1:3:6) type C-0 (including earth work in any type of soil, removal of surplus soil to a distance n.exc.50m) and connecting, testing on completion, all as shown on electric plate No. 03 of SSR-2009 Part-I, complete all as directed. Notes: 1. Earth lead & protection pipes length upto & including 7.50 metre is deemed included in unit rate quoted by the contractor. 2. Earth filling shall be done by vegitable soil. 3. Soil shall be free from stone, boulders, aggregate, gravels .

dadwal engineers

A V BUILDERS

M/S CANTILEVER ENGINEERS

M/S INDIAN ELECTRICAL

naresh kumar sharma

M/S TARA CHAND CONSTRUCTION CO.

Walia trading co

KULBHUSHAN AGGARWAL