PROVN OF RAIN WATER DRAINAGE SYSTEM AND SPL REPAIR TO JOINERY ETC AT APS NAGROTA UNDER GE NAGROTA

Amount

Taking down chowkats or frames with shutters (without taking off shutters from the frames) not exc 1.50 sqm each and removing from site complete all as specified & directed.

Taking down chowkats or frames with shutters (without taking off shutters from the frames) exc 1.50 sqm eachand n exc 4 sqm and removing from site complete all as specified & directed.

Supply fabricate & fix in position anodised aluminium powder coated (minimum thickness of powder coating 50 micron) door shutter with frame, partly glazed with 5 mm thick tinted glass and partly panelled with 9 mm thick prelaminated particle board with both side decorative laminated including rubber bead joining cleat for fixing in position, aluminium door handle 150 mm size, aluminium barrel tower bolt 200 mm size etc including taking down or and making good of disturbed surface all as specified below complete all as specified and directed. (a) Frame (top & side) section shall of size 101.60 x 44.75 x 2.4 mm ( Section No 14021) (b) Vertical Members of shutter Section shall be be of size 85.00 x 44.45 x 2.00 mm (Section No 19560) (c) Top Members of shutter Section shall be be of size 83.50 x 44.45 x 2.00 mm (Section No 19581) (d) Lock rail (Middle member) of shutter Section shall be be of size 150.00 x 44.45 x 3.00 mm (Section No 19596) (e) Bottom Members of shutter Section shall be be of size 150.00 x 44.45 x 3.10 mm (Section No 19584) (f) Glazing clip for securing glass of shutters shall be be of 0.80 mm thick (Section No 19370).Make- Jinal Section,

S&F Anodised aluminium frame for door section/ window section/ ventilator section for side hung type shutter /sliding type shutter/fixed type shutter in two or more tracks, including automatic locking handle , rollers and roller plate & fitting arrangement complete all as all as specified and directed by Engineer-in-charge.(Glass pane , hydraulic door closer , plush plate, floor hinges shall be measured and paid separately.

S&F Anodised aluminium window and ventilator shutters, /sliding type shutter/fixed type shutter in three or more tracks, including automatic locking handle , rollers and roller plate & fitting arrangement complete, aluminium sections weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as 4mm thick Glass panes, wiremwsh cloth0.63mm nominal dia of wire and average width of aperture 1.40mm, 150mm long (1 no.). hinges type B-21 100mm long (2 no.) suitable handle (1no.) complete all as specified and directed by Eng-in-charge.

S&F Sheet glass 4mm thick, ordinary quality and glazing fixed with aluminium section in squares not exceeding 0.5Sqm in each pane complete all as specified & directed.

S & Ffloor Door closer hydraulically regulated of Aluminium (Extruded section) body designation No.3, universe type, suitable for door shutters of 850 to 1000mm in width and of weight between 61 to 80 kg and fixed complete all as specified and directed.

S&F galvanised mild steel wire cloth, 0.63mm nominal dia of wire and average width of aperture 1.40mm and fixed with tinned tacks, or galvanised wire staples etc complete all as specified & directed.

Taking down cement plaster on brick or stone wall etc including racking out joints, hacking for key scrubbing down with water etc to receive new plaster etc. complete all as specified & directed.

Dismantling of brick bats and taking down existing old tarfelt or plaster, bituminous compound including cleaning & removing debris to a distance exc 100 m n.exc.250m. complete all as specified & directed.

M&L for 10 mm rendering in CM 1:4 including water proofing compound @2% of cement over roof surfaces finished even and smooth without using extra cement complete all as specified Note:- WPC Mesured and Paid Separately.

Supply only for Integral water proofing compound complete all as specified & directed.

M&L for Applying bituminous primer @ 0.40 litre per Sqm over plastered surfaces of roof including parapet surfaces complete all as specified & directed.

M&L for Applying evenly a tack coat of induatrial bitumen 85/25 grade @ 1.2 Kg/Sqm. complete all as specified & directed.

M&L for One layer of APP based polymeric membrane of approved manufacturer, 3mm thick, weight not less than 3.50 Kgs per Sqm , reinforced with non woven polyester fabric or weight not less than 150 gms per Sqm . Polymeric membrane shall be taken to a height 60 cm (minimum) and then inserted inside the groove of parapet wall and shall be finished by a membrane flashing(Note (i) Laying of APP based polymeric membrane shall be done by torch on method or as per manufacturers instructions (ii) A Minimum overlap of 100 mm and 75 mm should be made in the end and sides of the polymeric membrane respectively and sealed all overlaps and joints as manufacturers instructions (iii) The make of polymeric membrane shall be IWL India Ltd chennai. Ltd or "MOPLY FP" of Texsa India Ltd). NOTE : S&F of APP based polimeric membrane of approved manufacturer will be laid/fixed by authorised person of the same manufacturers units asper relevent IS.

M&L for Cement concrete tiles 25 cm x 25cm x20mm thick machine pressed set jointed and pointed in neat cement slurry on roof over APP membrane laid over 15mm thick cement screed bed in cement mortar 1:6 complete all as specified & directed.

PCC 1:2:4 type B-0 (12.50mm graded aggregate) as in padding finished even and smooth without using extra cement complete all as specified & directed.

Demolition of brick work built in cement mortar including all quions, arches, pillars etc but excluding ashlar facings dressed stone work and precast concrete articles complete all as specified & directed.

M&L for Brick work with sub class “B” bricks straight or curved on plan exc 6M mean radius build in CM 1:6 using all as specified using old size bricks complete all as specified & directed.

M&L for 200x12mm thick pre-formed filler board fixed at vertical portion of crumple joint( from ground floor to 3rd floor) complete all as specified & directed.

S&F plain black mild steel sheeting 0.80mm thick as in ridge, valley gutter & fascia,drip and straight flashing complete all as specified & directed.

M&L for Rendering 15mm thick on fair faces of brick work or concrete surfaces in CM 1:6 finished even and smooth without using extra cement all as specified ( internally) complete all as specified & directed.

Demolition of cement concrete (unreinforced) of any description and any position not other wise specifically provided complete all as specified & directed.

M & L for Preparation of newly plastered surfces of walls and applying two coats of oil bound distemper over a coat of wall care putty 3mm thick complete all as specified & directed.

M & L for Complete removal of existing treatment from external surfaces (any number of coats) of walls by steel wire brushing and washing rubbing down and stopping of surface holes and cracks using necessary filling compound of white cement and fine sand in the ratio of 1:3 to obtain smooth regular/even finish using sand paper and applying 3 mm thick wall putty and one coat of primer and two coats of oil emulsion distemper white or tined on wall upto three storie building complete all as specified. Note:- Shade of the OBD shall be approved by GE.

Excavating over area n. exc 1.5 m in deep and getting out in any type of soil. complete all as specified & directed.

Returning filling in including spreading, levelling, watering and well ramming in layers n. exc 25 CM in any type of soil. complete all as specified & directed.

Removing excavated meterial n exc 50 m and depositing where directed at a level n exc 1.5 m above starting point in soils complete all as specified & directed.

M&L Cement concrete Type D-2 1:4:8 (using 40 mm graded aggregate) in foundations, filling and mass concrete complete all as specified & directed.

M&L Brick work with subclass 'B' well burnt old size bricks straight or curved on plan exc 6 m mean radius built in cement mortar 1:4 exc 6m mean radius complete all as specified & directed.

M&L PCC 1:2:4 type B-1 using 12.5mm graded crushed stone aggregate as in copings, plinth course, damp proof course, bed blocks, benching, PCC cills and similar items.complete all as specified & directed.

M&L for PCC (1:3:6) Type C1 using 20mm graded stone agg as in surface channel & drain incl form work complete all as specified & directed.

M&L Rendering 15 mm thick on other than fair faces of brick work, stone masonry or concrete surfaces in cement mortar 1:4 on wall surfaces, finishing the surface even and smooth with out using extra cement complete all as specified & directed.

M& L for Extra for forming fair finished drain or channel 25cm inner girth in cement concrete using extra cement including forms ,moulds,mitred/stopped ends etc complete all as specified & directed.

Add or deduct for each 25mm girth over under 30 cm girth complete all as specified & directed.

U K Engineering Works (BID ID -3272837)

Malik Construction (BID ID -3273171)

BHARTI CONSTRUCTIONS (BID ID -3276854)

M/S Shankardass Devidass (BID ID -3276771)

M/S MANISHA BUILDERS (BID ID -3277012)

R.K. Works (BID ID -3277064)