REPAIRS TO DRAINS, COMPOUND WALL, FENCING, HARD STANDING AND PCC PATH AT AGE B/R-I UNDER GE GOLCONDA

Amount

Demolition of cement concrete (Un-reinforced) in ground floors and pavings n exc. 15cm thick (Below or above ground level).

M&L for 100 mm thick PCC 1:2:4 type B-1, (using 40mm graded stone aggregate) for footpath / hard standing finishing surface of concrete even and rough without using extra cement complete all as specified and directed.

Demolition floor, hearth or wall tiling including cement mortar bedding (but not backing) and removing rubbish off the premises complete all as specified and directed.

M & L for 60mm thick machine pressed precast cement concrete tiles of interlocking pattern with grey cement and pigment rubber moulded with vibration technology set and jointed as per manufactures instructions laid over and including 50mm thick crushed stone sand cushioning complete all as specified and as directed by Engr-in-charge. Note : Rate quoted by contractor shall deemed to inclued for filleting the side of pavement with PCC (1:2:4) type B1.

M&L for 75mm thick PCC 1:4:8 type D2 (using 40mm graded stone aggregate) as in sub base and finishing surface of concrete even and rough to receive the topping layer.

M&L chequered cement concrete tiles 300x300x25 mm thick with grey cement and pigment, machine pressed, set jointed and pointed in neat cement slurry in floors including 15 mm thick screed bed layer in CM 1:6 complete all as specified and directed.

Dismantling fencing wire mesh of any type & description..

Supply only MS galvanised chain link fencing haevy zinc coated (Hot dip), aparture size 50mm and wire of 8 Swg (4 mm) complete all as specified and directed by Engineer-In-Charge.

Fixing only chain link fencing any mesh size and type to any type of standard, rails, iron angle posts, straining bolts etc including provision of binding wire complete all as specified and directed by Engineer-In-Charge.

S & F in repairs galvanised, 2 strand, steel barbed wire 2.24mm dia barbed with 2mm dia barbs at 75mm spacings and straining and fixing to any type of standard rails straining bolts, including securing or tying at crossings with and provision of galvanised mild steel wire, staples or steel pins etc. complete all as specified and directed.

Dismantling wrought iron or mild steel work of any description not otherwise provided for.

S & F Mild steel work Angles, bars, flats etc. as in fencing post struts including cutting tops to shape as directed including embedding in concrete and all necessary drilling holes, bolting or riveting , welding notching for wire and similar work confirming to Fe 290 Gde-E-165 complete all as specified and directed.

M&L mild steel framed work as hung gates, including pintle hinges, stops, hand-made sliding bolts, etc. as grills, gratings, etc with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks, and similar work conforming to Fe.290.Gde-E-165

Dismantling posts or struts (wood, steel or R.C.C.) any section, including taking out embedded portion in concrete or brick work and making good disturbed ground complete all as specified and directed.

Excavating post holes or similar holes, each not exceeding 0.5 Cu. M, getting out in hard/ dense soil, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm, watering, and removing surplus soil to a distance not execeeding 50 M and making good surface complete all as specified and directed.

M & L for PCC (1:3:6) type C-2 (using 40mm graded stone aggregate) as in foundation filling & mass concrete for post/pillars etc complete all as specified and directed.

M & L for preparation of new or previously untreated steel surfaces of any description, over 10 cm width or girth, not otherwise described and applying two coats of synthetic enamel paint over a coat of red oxide zinc chrome primer complete all as specified and directed.

Demolition of brick work or stone/ boulder /PCC block masonry, built in cement mortar including all quoins, pillars etc.

M&L for square rubble masonry Secundearbad pattern , well bonded, bedded and solidly hearted, built in cement mortar 1:6 complete all as specified and directed.

M & L for PCC type D2 1:4:8 ( using 40mm graded stone aggregate) in foundations, filling and mass Concrete complete all as specified and directed.

M&L for flush pointing with CM 1:4 to random rubble masonry, uncoursed or brought upto course complete

M&L brick work with fly ash bricks built in CM 1:6 straight or curved on plan exc 6 mtr mean radius all as specified.

M&L Rendering 15mm thick on brick work or concrete surface of walls in cement mortar 1:4 and finished even and smooth without using extra cement complete all as specified and directed.

M&L Rendering 15mm thick on fair faces of stone masonry surface of walls in cement mortar 1:4 and finished even and smooth without using extra cement complete all as specified and directed.

M&L for Preparing of Newly plastered surfaces and applying three coats of white wash on walls complete and all as specified and directed by Engr-in-Charge.

M & L preparation of new surfaces of walls plastered or unplastered etc and applying two coat of cement based paint paint on wall surfaces as specified and directed by Engr-In-Charge.

Demolition of Concrete (Reinforced) of any description and in any position not otherwise specifically provided complete all as specified and directed by Engr-in-Charge.

M&L for Pre Cast Cement Concrete 1:2:4 type B1 (using 20 mm graded aggregate) as in Cover slab for manholes etc set in cement mortor 1:6 including use and waste necessary form work (Reinforced shall be measured and paid seprately) complete all as specified and directed.

M&L for MS TMT bars, 5mm dia and over upto and including 10mm dia in stirrups, spacers and binders , cut ot length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with wire complete all as specified and directed.

M&L for MS TMT bars, 10mm dia & over , cut ot length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with wire complete all as specified and directed.

M&L PCC 1:2:4, type Bo (using 20 mm graded stone aggregated) as in copping/ benching to manholes and drains including necessary form work complete all as specified and directed.

Taking down cement plaster any description on brick or stone walls, roof plater etc including raking out joints,hacking for key, scrubbing down with water etc. complete all as specified and directed.

M&L Rendering 10mm thick on brick work or concrete surface in cement mortar 1 : 6 and finished even and smooth without using extra cement complete all as specified and directed.

M & L for pre-cast cement concrete block masonry with solid blocks 1:3:6 Type C1(using 20mm graded stone aggregate) exc. 10 cm in width and setting in mortar (1:6) complete all as specified and directed.

S & F mild steel screw bolts of 11 to 15mm diameter of neck (machine made) with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut, length of bolt exc 5cm and not exc 10cm complete

STANDARD AGENCIES

RAFEEQ AND CO

Sri Lakshmi Enterprises

M/S Veerabhadra Constructions

Sumpoorthy Engineers

Neeru Constructions