SPL REPAIR TO BLDG NO P-01 (ZONE 11), P-5, 19 (01 TO 08), P-30/01 TO 08 (08 QTRS) AND PROVN OF CHANIN LINK FENCE FROM RP GATE TO BLDG NO P-27 UNDER AGE B/R-I AT GE BABINA

Amount

Demolition of PCC/lime concrete (Other than Ground flooors) terracing including felt in any description and in any position over roof etc complete all as specified and as directed by the Engineer-in-Charge.

M&L for P.C.C 1:2:4 type B-0 using 12.5 mm graded stone aggregate as in padding over roof finished and laid to required slope complete all as specified and as directed.

M&L cutting out cracks to 'V' Section in existing roof or terracing, cleaning out, wetting and filling solidly a hot mixture of bitumen and dry sand in proportion of 1:1 by weight complete all as specified and as directed.

Cutting grooves in brick wall 75mm wide and 65mm deep and shaping horizontal face of groove with cement mortar 1:3 complete all as specified and as directed.

M&L, roughening surfaces of old concrete roof by picking ,sweeping clean and washing down with water to remove dust etc and applying a coat of cement slurry @ 3 Kg per Sqm complete all as specified and directed.

M&L for P.C.C 1:2:4 type B-0 using 12.5 mm graded stone aggregate as in coping on roof chamfered on edge including troweling slightly complete all as specified and as directed.

M&L for 10 mm thick screed bed in cement mortar 1:4 on concrete surfaces when concrete is stil green finished even and fair including mixing of water proofing compound as per manufacturer instruction etc complete all as specified and as directed.Note :- Water proofing compound shall be measured separately as supply only in item no 07

Supply only Liquid water proofing compound complete all as specified and as directed of as per manufacturer instruction.

M&L applying water proofing treatment with the following:- (a) First coat of bitumen primer conforming to IS-3384 @ 0.3Kg / sqm to be applied on prepared surface till the surface is properly impregnated. (b) After the application of approved bituminous primer the water proofing memberne minimum weight 3kg/sqm and minimum 3mm thick reinforced with polyesterd non woven fabric (weight not less then 160gms/sqm) shall be laid on the primed surface by torch application method as per manufactured instruction. (c) All joints and change in direction should be curved with cement mortar (1:3) mixed with SBR latex @ 200ml per bag on cement and cured well before laying of membrane. ( d ) M&L for preparation of newly surface of APP membrane and applying two coat of bituminous aluminium paint @200 gm /sqm etc complete all as specified and as directed.

Taking up or down existing steel tubing and connections including cleaning for refixing or removal to store complete all as specified and as directed for the following sizes:-

(a) 15 mm dia bore

(b) 20 mm dia bore

Supplying, fixing, jointing and testing galvanised iron tubing medium grade with all fitting such as bends, elbow, socket, reducer etc and fixed to wall or laid in floor complete all as specified and as directed for the following sizes:-

(a) 15 mm dia bore

(b) 20 mm dia bore

Fixing only old steel tubing and connections obtained from taking down against item No 8(a) & (b) herein before in new or old position fixed to wall, ceiling or laid in floor with new fittings for the following sizes:-

(a) 15mm dia bore

(b) 20mm dia bore

Cutting chases, pinning in, making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels etc., and cutting chases for concealed water tubing or concealed conduit wiring, etc., and making good, cuttingexceeding 10 cm but not exceeding 20 cm girth in brick walls

Dismantling water tanks and removing to store of steel/PVC of capacity 500 ltr but not exceeding 1000 Ltr complete all as specified

S&F 1000 ltr capacity or rotational moulded polyethylene water storage tank (cylindrical vertical with closed top) ISI marked or make specified, three layered construction hoisted and fixed in position including S&F 20mm dia GI pipe medium grade washout pipe 450mm long with plug and 20mm dia gi pipe medium grade overflow pipe 600mm long with fitting complete all as specified in SSR Part -I complete all as specified and as directed

Fixing only old1000 ltr capacity rotational moulded polythene tanks (cylindrical vertical with closed top) hoisted and fixed in position including dismantling existing and cleaning complete all as specified and as directed.

S&F 20mm bore ball valve high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball screwed for iron pipe and fixed (Minium weight 210 gms ), complete all as specified and directed

S & F in repair 20mm dia Gun metal gate valve with iron wheel head, screwed both ends for iron pipe complete all as specified and as directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises and complete all as specified and as directed.

M&L for screed bed or bedding layer in CM 1:6, 15mm thick complete all as specified and directed.

M & L rendering 10mm thick in cement mortar (1:4) on fair faces of brick work or concrete surfaces as in vertical surfaces for receiving tiles as directed.

M&L for dark coloured ceramic tiles 7 to 8 mm thick (square / rectengular) area of each tile exceeding 0.36 sqm but not exc 1.00 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match to floor etc complete all as specified and as directed.

M&L for dark coloured ceramic tiles 7 to 8 mm thick (square / rectengular) area of each tile exceeding 0.36sqm but not exc 1.00 sqm, in Skirting etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match to floor etc complete all as specified and as directed.

M&L for dark coloured ceramic tiles 7 to 8 mm thick (square / rectengular) area of each tile exceeding 0.36sqm but not exc 1.00 sqm, in dado/Skirting etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match to floor etc complete all as specified and as directed.

M&L for non skid dark coloured ceramic tiles 7 to 8 mm thick (square / rectengular) area of each tile exceeding 0.36sqm but not exc 1.00 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match to floor etc complete all as specified and as directed.

M&L for 15-20mm thick Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window cills, cooking platforms and like including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite over 15 mm thick in CM(1:6) etc complete.

Demolition of PCC in any description and in any position etc complete all as specified at site

M&L for 75mm thick cement concrete type C-1, 1:3:6 (20mm graded aggregate) as in plinth protection with soucer drain finished even and smooth without using extra cement complete all as specified and directed

M&L for 40mm thick cement concrete type B1, 1:2:4 (20mm graded aggregate) as in floor/hardstanding finished even and smooth without using extra cement complete all as specified and directed.

Demolition of brick work built in cement mortar

M&L brick work with sub class 'B'brick straight or curved on plan exc 6m mean radius built cement mortar 1:4 complete all as specified and as directed

M & L Brickwork with fly ash bricks, straight or curved on plan exc 6m mean radius, built in cm (1:6), rise of hight for brick wall.

Taking down cement plaster on brick or stone wall including raking out joints, hocking for key scrubbing down with water etc complete all as specified and as directed.

M&L for rendering 10mm thick on fair faces of wall even and smooth finish without using extra cement on conc/brick surfaces in CM 1:6, complete all as specified and as directed

M&L renderig 5mm thick in cement mortar 1:3 on ceiling surface and finished even and smooth with out using extra cment complete all as specified and as directed.

M&L for rendering 15mm thick on fair faces of wall even and smooth finish without using extra cement on conc/brick surfaces in CM 1:4, complete all as specified and as directed

M & L for preparation of new plastered surface and applying three coat of white wash on ceiling complete all as specified and as directed.

M & L for Preparation of new plastered surfaceof wall and applying two coat of OBD over a coat of putty complet all as specified and as directed.

M & L for applying two coats of 100% Premium acrylic plastic emulsion paint on new surface having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over surfaces including prepration of new surface complete all as specified and directed by Engr-in-Charge.

Taking down chowkhat or frames with shutters (without taking off shutters from the frame) exe 1.5 Sqm but n exc 4 Sqm each etc complete all as specified and as directed

Taking down chowkhat or frames with shutters (without taking off shutters from the frame) not exe 1.5 Sqm each complete all as specified and as directed.

S&F Factory Made Solid PVC Moulded Door Shutter With Particle Board Core, 28 to 30mm thick (stiles), with 2, 4, or 6 raised panel design with 2mm thick Moulded PVC Sheet on the front face & 2mm plain colour PVC sheet on back face, supplying & fixing in frame at site as per specification & drawing all as directed and specified by Engineer-in-Charge.

S & F Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other Frames/ Chowkhat of size 50 x 100 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast, SS butt hinges with screws as required / lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge. Note: For WPC solid door/window frames, minus 5mm tolerance in dimension i.e. depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made

S&F Stainless Steel tower bolts of extruded section & fixed 150 mm long etc complete all as specified and as directed

S&F Stainless Steel handles cast type anodized 150 mm size etc complete all as specified and as directed

S & F butt hinges medium weight cold rolled, mild steel and fixed 100 mm size etc complete all as specified and as directed..

S&F 300 mm long Stainless Steel sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast- aluminium alloy.

S&F Pressed steel frames for doors(125x60) mm with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc., complete as specified, supplied and fixed etc complete.

S&F Pressed steel frames for doors(105x60) mm with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc., complete as specified, supplied and fixed etc complete.

Cutting holes in brick walls built in cement mortar for inserting hold fasts and making good dismantled portion in CM 1:3 or cement conc 1:2:4 type B1 as required exc half brick but not exc full brick wall complete all as specified and as directed.

M&L PCC 1:3:6 type C-O (using 12.5mm graded stone aggt) as in filling in holes of hold fasts and back filling of chowkats complete all as specified and directed.

M & L Secound class hardwood Plain, solid, straight chowkats and frames wrought framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints, all as directed.

S&F 18/19 mm thick prelaminated particle board century interior grade prelaminated one side with decorative choice laminations and other side balancing white lamination fixed with screws to timber frame work including cover fillet of external teak wood & piano hinges & magnet door catcher for each shutter etc complete all as specified and directed by Engr-in-Charge.

S&F Hasp & staple safety type Stainless steel hing pin incl bolt to hing plate and fixed with screws 100mm size etc complete.

S&F factory made 35mm thick 2nd class Hard wood paneled door shutter factory made (two panel) with lock rail andpanel of 9mm thick BWP commercial ply wood, the size of rail and stile is as per IS 1003 (Part-I), Kiln seasoned and chemically pressure treated complete all as specified and as directed

S&F,factory made 35 mm thick IInd class HW partly paneled& Partly gauged & skeleton shutters open rebated and prepared to receive glass/gauge etc. (without sash bars) edges of framing plain chamfered or rounded fitted with cut & mitered beads for security glass/gauge etc. size of members of shutter as specified in SSR Pt I sec 8 Cl 8.20 (a), divided into squares with plain chamfered rounded, mitered and rebated sash bars etc complete all as specified and as directed

S&F factory made fabricated 35 mm thick IInd class HW glazed & skeleton shutters open rebated and prepared to receive glass gauge etc. (without sash bars) edges of framing plain chamfered or rounded fitted with cut & mitered beads for security glass/gauge etc. size of members of shutter as specified in SSR Pt I sec 8 Cl 8.20 (a), divided into squares with plain chamfered rounded, mitered and rebated sash bars etc complete all as specified and as directed

S & F Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other Frames/ Chowkhat of size 65 x 125 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge. Note: For WPC solid door/window frames, minus 5mm tolerance in dimension i.e. depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made Note: stainless steel butt hinges 03 Nos with with 32mm long SS screws and Other hardwares should be fixed with 19*6mm size steel screws etc. M.S. hold fast/ lugs or SS dash fasteners shall be included).

Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid decorative type flush door shutter of size 35mm thick comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant. WPC to be laminated with PVC foil of minimum 14 microns thick of approved design pasted with hot melt adhesive on both faces of shutter and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of EngineerIn- Charge. Note: Each shutter shiould be fixed with stainless steel butt hinges 03 Nos with 32mm long SS screws and Other hardwares should be fixed with 19*6mm size steel screws etc.

M&L, powder coated aluminium frame for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc. complete all as specified and directed by Engr-in-Charge.

M&L for aluminium powder coated glazed door shutter ( Single leaf ) fabricated out of approved powder coated aluminium sections , shutter having bottom rail of section size 114.50 mm x 44.50 mm x2.0 mm thick section, middle and top rail of section 84.50 mm x 44.50 x 2 mm thick section and styles of section size 84.50 mm x 44.50 mm x 2 mm thick and S & F 5.5 mm thick tinted glass in panel of shutter fixed with glazing clips , rubber gasket and powder coated aluminium snap beading so as to make air tight and including S & F powder coated butt hinges type C-1 ,100 mm size 3 nos per shutter , powder coated aluminium handle of 150mm size 2 Nos (One on each side of shutter) , powder coated aluminium tower bolt of size 200 mm ( 2 Nos ) per shutter , mortise lock , brass body ,6 levers ( 1 No) with duplicate keys , aluminium (extruded section) hydraulic door closer regulated designation No-3 Universal type ( 1 No) & Floor door stopper ( 140 mm ) overall ,aluminium body 1 No on each shtter etc complete all as specified and as directed. Note: (i) Shutter ( Glazed ) shall be fixed on frame of required size and shall be measured seperately (iii) Cost of all fittings & fixture shall deemed to be included in unit quoted rate by the tenderer . Note : The minimum thickness of powder coating shall be 50 Micron .

S & F powder coated aluminium window/ventilator colour as approved by GE with double hung shutter (both gauged and glazed ) including alumunium grill of size 50x50mm with 6mm dia bar fixed with GI wire mesh cloth 0.46mm dia of wire and 1.18mm aperature , both fixed on aluminium frame 126 mm x 50 mm x1.5 mm thick , shutter with bottom rail, middle rail, top rail and styles of size 44.45 mm x 47.62 mm x 1.2 mm thick as per IS 737-1986 and glazed with tinted glass (Modi guard ) 5 mm thick as per standard practices and with alumunium powed coated handle & tower bolt arrangements incl taking down existing windows etc complete all as specified and as directed.

S&F stainless steel wire cloth 0.63 mm nominal dia of wire and avg width of a-pertare 1.40 mm fixed with tinned tacks or galvanized wire staples etc complete all as specified and as directed

M&L for preparation new wooden surface of any description not otherwise described over 10 cm width or girth and applying two coat synthetic enamel paint over one coat of pink primer etc complete all as specified and as directed

M&L framed work as grills, gratings, etc with ends of bars shouldered and/ or riveted into spikes; or forged into spikes, framed guard bars; barred iron doors and similar work confirming to Fe 290. Gd-E-165

S&F, mild steel, plain black sheet in wall cladding, steel gates and similar work, cut to size, holes punched; including round headed screws, clout nails or rivets and fixed to wood or steel framing with plain 40mm lap joints with riveted or welded seams, including bending or turning up, mitred angles, etc complete all as specified and as directed

M&L, preparing for new steel surfaces and applying two coats of synthetic enamel paint over one coat of rex oxide primer over 10 cm width or girth complete all as specified and as directed.

M&L, preparing for old steel surfaces and applying one coats of synthetic enamel paint over 10 cm width or girth complete all as specified and as directed.

S&F in repair vitreous china squatting pan “ORISSA” pattern size 58X 44 (CM) star white with P or S trap front or back inlet with integral foot rest (excl flushing cistern & flush pipe) & including connection to trap & to flushing pipe anti syphonage pipe etc complete including making good to floor complete all as specified & as directed.

S&F in repairs Vitreous chine wash down water closet pan(padestal pattern), white(EWC) including plastic seat of same colour of Wc, closed pattern with flat bottom, and cover mild steel chromium plated hinging device complete all as specified and directed

S & F in repair 10 ltrs capacity PVC low level flushing cistern sleek plus single flush of colour star white with inlet, float valve and handle with 32 mm dia PVC pipe 600 mm long complete all as specified and as directed.

S&F in repair pedestal vitreous china wash hand basin white flat back of size 450mmx300 mm including cutting for and pinning in ends of brackets or errecting stand but exclusive of fixing of waste pipe and CI brackets complete all as specified and directed.

S & F in repair Vitreous China Table top Wash hand basin any colour size 510 x 400 x135 mm size including waste pipe complete all as specified and directed

S&F in repair PVC connections 15mm size with PTMT nuts of length 450mm etc complete all as specified and as directed.

S&F in repairs 15mm dia Concealed stop Cock regular body 15mm with flange complete all as specified and as directed.

S&F in repair 15mm bore cast copper alloy chromium plated angle cock with flange complete all as specified and as directed.

S&F in repair 15mm bore fancy type chromium plated bib cock long body with flange etc complete all as specified and as directed.

S&F CP wall mixer 15mm dia bore mixing hot & cold water screwed down for iron pipe connect to showe and fixed complete all as specified and directed.

S&F CP wall mixer 15mm dia bore mixing hot & cold water screwed down for wash hand basin iron pipe and fixed complete all as specified and directed.

S&F in repair 15mm bore cast copper alloy chromium plated two way angle cock with flange complete all as specified and as directed.

S/F brass chromium plated health faucet for EWC screwed down to GI tubing/fittings 15mm dia incl 1200mm long stainless steel connection complete all as specified and directed.

S&F stainless steel towel rack fixed to wall with CP brass screws complete all as specified and as directed.

S&F in repair PVC floor trap outlet dia 75mm with grating including jointing to waste pipe fixed in cement concrete type B1 (1:2:4) complete all as specified and as directed.

S&F in repair Brass cromium plated towel rail 20mm dia, D type, 60cm long between flanges complete all as specified and as directed

S&F in repair 125 mm Brass chromium plated shower rose with or without swivel joints, any size, including fixing of steel pipe or union and fixed all as directed.

S&F stainless steel kitchen plate rack overall size 900mm x 900mm make out of 0.80mm thick stainless steel sheet etc complete.

S&F in repair stainless steel sink with drainage board 1.00mm thick for kitchen or laboretory with plug, waste pipe, coupling, washers also incl cantilever cast iron brackets connecting union etc, overall size 915x460mm with bowl size 410x330x160mm complete all as specified and directed.

Supply and fix in repair CP corner glass shelf with bracket fixed with screws complete all as specified and as directed by Engineer-in-Charge .

S&F in repair CP Brass soap dish fixed to wall with cp brass screws etc complete all as specified and as directed by the Engineer-in-Charge

S&F in repair 25 mm dia chromium plated curtain rod with CP brackets and knobs at both end as per sample approved by Engineer-in-charge.

S&F in repair concealed stop cock fancy type CP cast copper alloy screwed down high pressure with crutch or buttor fly handle screwed both ends for iron pipe or for unions and fixed 15mm bore complete all as specified and directed.

Demolition and breaking up drain pipes (Salt glazed ware, AC/PVC/CI or Reinforced concrete) set in cement mortar in floors or wall in 100mm dia meter complete all as specified and as directed.

S &F of 110mm dia PVC (SWR) pipes single socketed, in any length with rubber ring joints laid in trenches or in floors or wall and complete all as specified and directed.

S &F of 75mm dia PVC (SWR) pipes single socketed, in any length with rubber ring joints laid in trenches or in floors or wall and complete all as specified and directed.

S&F PVC (SWR) bends any radius 110mm bore.

S&F PVC (SWR) bends any radius 75mm bore.

S&F PVC (SWR) junction single, (single T) equal or unequal 75mm bore with access door.

S&F PVC (SWR) junction single, (single T) equal or unequal 110mm bore with access door.

S&F PVC (SWR) vent cowl 110mm bore.

S&F MS chromium plated peg set of five fixing with wall complete

M & L for complete removal of existing treatment of any description from walls and applying two coat of oil bound distemper over a coat of primer over 1 mm thick wall care putty (JK/Birla wall care putty ) including prepration of surfaces as per manufacurers instructions etc complete all as specified and as directed.

M & L for applying two coats of 100% Premium acrylic plastic emulsion paint on old surface having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over surfaces including prepration of surface complete all as specified and directed by Engr-in-Charge.

M&L, Preparing old plastered surfaces of ceiling and applying one coat of white wash complete all as specified and directed.

M&L for 150 mm Reinforced concrete pipes, class NP3, laid and jointed complete with collars laid in trenches and joints incuding all fittings as requited in the laing complete all as specified and directed by Engr-in-Charge.

M&L for type D-2 (1:4:8) concrete bed to drain pipes including packing under, and hunching against the side of pipe after they are laid and tested, in 150mm dia pipe complete all as specified and directed by Engr-in-Charge.

Excavation in trenches for fdn n.exc 1.5m wide and n.exc 1.5m in depth & getting out in soft /loose soil

Returning filling in including spreading ,levelling,watering and well ramming in layers not exc 25cm

Removing excavated at a level n.exc 50m m above the starting point

M&L, PCC 1:4:8 type D2 using 40mm graded stone agg as in filling and mass concrete, Sub base/flooring complete all as specified and directed.

M&L, sand cushioing to under concrete interlocking paver block including watering & consolidation complete all as specified

M&L 60 mm thick machine pressed rubber moulded coloured precast concrete interlocking paver block any shape & size confirming to IS 15658-2006 of 60mm thickness, M-35 grade with grey cement & pigment complete all as specified and directed.

S & F modular detergent pull out miniumum size 200x485x430mm made of stainless steel (SS-304) over roller and 45mm runners load capacity of 50 Kg , handle and auto closing hinges and all connected items as required in the fitting as per approved manufacturer,s specification premium quality including all fittings complete all as specified and as directed.

S & F modular thali-plate basket made ss stainless steel (SS-304), miniumum size of 520x485x100mm, over roller and 45mm runners load capacity of 50 Kg , handle and auto closing hinges and all connected items as requiredas per approved manufacturer,s specification premium quality including all fittings complete all as specified and as directed.

S & F modular perforated cutlery basket made of stainless steel (SS-304) miniumum size size of 520x485x100mm, over roller and 45mm runners load capacity of 50 Kg , handle and auto closing hinges and all connected items as required as per approved manufacturer,s specification premium quality including all fittings complete all as specified and as directed. Make Godrej /hitech/kutchina Kitchen appliances or other equivalent make as approved by GE..

S & F dish rack made SS stainless steel (SS-304), miniumum size of 570x280mm as per approved manufacturer, over roller and 45mm runners load capacity of 50 Kg , handle and auto closing hinges and all connected items as requiredspecification premium quality including all fittings complete all as specified and as directed. Make Godrej /hitech/kutchina Kitchen appliances or other equivalent make as approved by GE..

S & F in auto closing waste bin made stainless steel made of stainless steel as per approved manufacturer, over roller and 45mm runners load capacity of 50 Kg , handle and auto closing hinges and all connected items as required specification premium quality including all fittings complete all as specified and as directed. Make Godrej /Hitech/kutchina Kitchen appliances or other equivalent make as approved by GE..

S & F in bottle pull out made stainless steel (SS-304) Miniumum size100x485x430mm as per approved manufacturer, over roller and 45mm runners load capacity of 50 Kg , handle and auto closing hinges and all connected items as required specification premium quality including all fittings complete all as specified and as directed. Make Godrej /Hitech/kutchina Kitchen appliances or other equivalent make as approved by GE..

S & F in plain basket made stainless steel (SS-304), Miniumum size of 520x485x100mm as per approved manufacturer, over roller and 45mm runners load capacity of 50 Kg , handle and auto closing hinges and all connected items as required specification premium quality including all fittings complete all as specified and as directed. Make Godrej /Hitech/kutchina Kitchen appliances or other equivalent make as approved by GE..

S&F of 18mm MDF on borh side laminated (prelam sheet) for shutter base/wall kitechen cabinets/cupboard and /shutter alongwith auto closing 35mm hinges o crank (KH-001) or 8 crank (KH-002) and handle of fency type and all connected iterms etc. as per approved manufacture,s specification premium quality including all fittings complete all as specified and as directed.

S & F of 18mm MDF on both side laminated (prelam sheet) for Shelves White in kitchen cabinets/Cupboards etc. as per approved manufacturer,s specification premium quality including all fittings complete all as specified and as directed.

S & F of 18mm BWR Ply on both side laminated (prelam sheet) for Frame in kitchen cabinets/Cupboards etc. as per approved manufacturer,s specification premium quality including all fittings complete all as specified and as directed.

S & F of 18mm MDF on both side laminated (prelam sheet) for Framing partition in kitchen cabinets/Cupboards etc. as per approved manufacturer,s specification premium quality including all fittings complete all as specified and as directed.

S & F of 18mm MDF on both side laminated (prelam sheet) for Back and Base in kitchen cabinets/Cupboards etc. as per approved manufacturer,s specification premium quality including all fittings complete all as specified and as directed.

S & F in 18mm BWP ply on both side laminated in Wall cabinet Minimum size 700x700x300 incuding 0 degree stainless steel kutchina/Hafele intermate hinge (heavy duty) , Economic Handle stainless steel, shelves support , L-clip, multitech railing set , as per approved manufacturer,s specification premium quality including all fittings complete all as specified and as directed.

S&F as in repair 15 mm bore CP fancy type sink mixer long body tab (wall mounted) with 150mm (6") long swivel spout, wall flange and provision for water Point connection, cast copper alloy screwed down, screwed for iron pipe or for brass ferrule.complete all as specified and directed.

Supply, Fixing and installation of wall mounted Electric Kitchen Chimney of size 75 cm, compact design suction 1400m3/hr Auto clean type touch control with wave sensor duct dia 150mm including free Kit for installation with duct cover of adequate size ,kutchina and equivalent make as approved by GE.

S&L for Steel rolling shutters (Thickness of laths 1.00mm), but gear operated type with chain wheel and hand chain, as specified including top cover, anchoring rod, hasp and staple and one shop coat of primer; erected in position as indicated, complete: push pull or manual type inclduing shaft and all items which are required to established of the shutter inculding safety lever lock & Ball bearing as required completed and including taking down of existing rolling shutters all as specified and directed by Engr-in-Charge.

M/L for rendering 15mm thick in CM 1:4 on fair faces of bricks or concrete surfaces finished fair and smooth complete all as specified and directed by Engr-in-Charge.

M & L preparation of walls newly plastered surfaces & applying two coats of white wash complete all as specified and directed by Engr-in-Charge. .

Demolition of un-reinforced cement concrete in ground floors and pavings not exceeding 15 cm thickness, (Below or above ground level) and disposal of unserviceable materials, debris and rubbish to a distance not exceeding 100 M as directed by the Engineer in Charge.

M & L for cement concrete type C2 (1:3:6) (using 40 mm graded stone aggregate) in surface channels, drains and manhole foundation etc complete all as specified and directed by Engr-in-Charge. .

M&L for PCC 1:2:4 type B1 (using 20mm graded aggregate) in copings, kerbs, channels, water through and the like including weathering, slightly rounded or chamfered angles and throating as directed chamfered necessary for work

M&L, for extra for forming fair finished drain or channel 30 cm inner girth in cement concrete, using ex- tra cement, including forms, moulds, mi- tred/stopped ends etc complete all as specified and directed by the Engineer in Charge.

Demolition of reinforced cement Concrete of any description and in any position disposal of unserviceable materials, debris and rubbish to a distance not exceeding 100 m as directed by the Engineer in Charge. (Reinforcement shall be cut as required to facilitate demolition).

M & L for precast reinforced cement concrete (1:2:4), type B-1 (using 20 mm graded stone aggregate) as in cover slabs with holes and similar articles with plain faces and set in cement mortar (1:4) complete all as specified and directed by the Engineer in Charge.

M & L for mild steel TMT bars 8mm dia., and over cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with mild steel wire (annealed) not less than 0.9 mm dia., or securing with clips. complete all as specified and directed by the Engineer in Charge.

M & L for surface dressing nexc 15 cm deep , site clearance , to remove the bushes and making area workable

Excavation in post holes each n exc 0.5 cum and getting out in hard/dense soil, returning, filling in and ramming earth in layers n exc 25 cm, watering, and removing surplus soil to a distance n exc 50 m and making good surface all specified and directed.

M&L PCC (1:4:8) type D-2 (using 40mm graded aggregate) as in foundation filling and mass concrete etc all as specified & directed.

M&L PCC (1:2:4) type B2 (using 40mm graded aggregate) as in foundation of posts etc all as specified & directed.

S&F posts and struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire, etc.; flat iron fillets (for securing wire mesh etc.) including all necessary drilling, bolting or riveting, etc., and similar work conforming to Fe-290 Gde E-165 all specified and directed.

S&F MS Screw bolts 10 mm dia (machine made) with hexagonal or square heads at one end and screwed the other, embeded in RCC post, each screwed end to be fitted with washers and one hexagonal or square nut, length of bolt exc 10 cm but n. exc 15 cm long all specified and directed.

S&F Mild Steel Flats 40 x 6 mm thick in wind ties for roof inclduding securing bolts, posts and struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire etc; flat iron fillets (for securing wire mesh etc) including all necessary drilling, bolting or riveting etc conforming to Fe-290 Gde E-165 all specified and directed.

Material supply only MS galvanised chain link fencing any size or type all specified and directed.

Fixing only chain link fencing including line wires, any mesh, size and type to any type of standards rails, straining bolts, etc, including provision of binding wire all specified and directed.

S&F 10 mm dia round bars as stiffening member in fencing including securing the fencing confirming to Fe-410-W (gde-E-250) qualiity A or Fe-290 (Gde-E-165) as link all specified and directed.

M&L for applying two coat of Black Japan paint over a coat of red oxide primer on steel surfaces of any descripition over 10 cm width or girth etc complete all specified and directed.

M & L for applying two coat of synthetic enamel paint over a coat of red oxide primer to steel and iron surfaces of any description over 10 cm in width or girth not otherwise described including preparation of new steel surfaces all specified and directed.

S&F galvanised, 2 strand, steel barbed wire 2.24 mm dia barbed with 2 mm dia barbs at 75 mm spacings and straining and fixing to entanglements aprons of standard rails straining bolts, including, securing or tying at crossings with and provision of galvanised mild steel wire, staples or steel pins etc all specified and directed.

Taking down carefully copper/ aluminium point wiring (light, fan, socket, or power) complete fitting such as switches, ceiling roses pendants, regulators, sockets, light fitting ceiling fan etc to be measured seperately ) removing materials for keeping in safe custody or for taking credit (credit for above items should be made as per conditions seperatly) and making good disturbed surface of walls floors etc all as specified and directed. Note-Responsibility after taking down fan/exhaust fan keep in safe custody of contractor and refix the same after before completion of work the rate of same deemed to be included in the item quoated rate.

Taking down carefully existing wooden board , Main switch, MCB DB boxes with MCBs, sheet metal boxes, cut out, etc of any size any capacity from boards complete all as specified and as directed.

Taking down carefully sub main wiring / service connection twin core from wall / LT pole of any size of Aluminum with wooden batten and or through rigid conduit including GI wire and making good the disturbed surfaces of walls, roofs, floors etc complete all as specified and as directed.

M & L for concealed point wiring complete with PVC insulated and unsheathed flame retardant low smoke and halogen ( FRLSH ) cable of 1.5 sqmm (nominal area) with multi stranded copper conductor single core 1100 volts grade in and including rigid PVC conduit not less than 20 mm dia, clip, with MS terminal boxes (not less than 1.6 mm thick) and painted with one coat of red oxide primer all around and two coats of black bituminous paint from out side and two coat of aluminum paint from in side including common earth dolly with 3 mm thick plastic laminated sheet top cover of approved make and colour including 1.5 sqmm green multi stranded copper conductor as continuous earth wire with lugs complete including cutting necessary chases on wall / ceiling surfaces for drawing of conduit & cables as required and making good disturbed surfaces of walls with CM 1:3:6 and matching with the existing surfaces including colour washing all as specified and as directed for the following :-

(a) One light point controlled by one switch

(c) one fan point controlled by one switch & regulator.

(d) One 3/5 pin 5 Amp socket outlet point controlled by one switch on independent board.

(e) One 3/5 pin 5 Amp socket outlet point controlled by one switch on same board.

(e) one bell/buzzer point controlled by one switch

M & L for concealed point wiring complete with PVC insulated and unsheathed flame retardant low smoke ( FRLS ) 1100 volts grade in single core multistranded cu conductor cable of size 4 sqmm for phase and neutral in and including concealed 20/25 mm dia pvc conduits, sheet steel sunken box 1.2mm thickness covered including with 3 mm thick plastic laminated sheet for mountning switches, socket , regulators etc and including 4 sqmm copper conductor pvc insulated and unsheathed multi stranded green cable as earth wire for power socket (geyser) complete all as specified and as directed. (unit rate quated including c;utting chases and making good the disturbed surface to match with the original. nothing extra shall be paid on this account)

S&F modular socket 20 amp with MCB 20 Amp 'C' type all specified and complete. (For geyser)

Description all as per item No 4 above but using 2.5 sqmm single core multi stranded copper conductor PVC insulated and unsheathed flame retardant low smoke ( FRLS ) cable for 3/6 pin 15 Amp socket outlet controlled by one switch on independent board with 2.5 sqmm green stranded copper conductor as continuous earth wire with lugs complete all as specified and as directed.

S&F switch piano flush button type 5 Amp single pole one way complete all as specified and as directed.

S&F socket outlet 2in1, 3 pin, 5 Amp flush type complete all as specified and as directed.

S&F switch piano flush button type 15 Amp single pole one way complete all as specified and as directed.

S&F socket outlet 2in1, 3 pin, 5 Amp and 15 Amp flush type complete all as specified and as directed.

S & F delux Fan Regulator electronic rotary, step type 240 Volt 50 Hz, complete all as specified as directed.

S & F Lamp holder,PVC/Urea type with back plate suitable for batten fittings complete all as specified as directed

S & F 9W/10W LED retrofit lamp B-22 holder base with polycorbonate body and aluminium heat sink complete all as specified as directed.

S&F electric bell, AC 230 volt, single pole, ding dong type complete all as specified

S&F modular bell push , piano type 6 amp SP one way

S&F ceiling rose,surface POLYCARBONATE 63 x50mm three terminals complete all as specified and as directed.

S&F in repair for concealed sub main wiring with PVC insulated, unsheathed 2 single core cable 1100 volts grade with copper conductor of size 6.0 sq mm (Nominal area) multi stranded drawn into conduit (Existing / new) with and including 6.0 sqmm green stranded copper conductor as contineous earthwire with lugs complete all as specified and as directed. NOTE. (I) New pvc conduit should be used not less than 25 mm dia. (ii) pvc conduit shall be deemed to be included in quoated rate itself.

S&F in repair for concealed sub main wiring with PVC insulated, unsheathed 2 single core cable 1100 volts grade with copper conductor of size 4.0 sq mm (Nominal area) multi stranded drawn into conduit (Existing / new) with and including 4.0 sqmm green stranded copper conductor as contineous earthwire with lugs complete all as specified and as directed. NOTE. (I) New pvc conduit should be used not less than 25 mm dia. (ii) pvc conduit shall be deemed to be included in quoated rate itself.

S&F TPN DB-DPX 125 MCCB DBs 4 way single door with provision for DPX 125 MCCB and as incomer and SP/TP MCBs as out going no of modules DPX 125+12, concealed Complete all as specified and as directed. Make:- ABB / Havells / HPL / Standard.

Supply and fix MCCB having breaking capacity of of 16 KA 415V, 4 pole having rating capacity of 125 Amp 100% ICU complete all as specified and as directed.

Supply and fixing mount sturdy LED Bollard 1 mtr height with excellent light out put through its PMMA widow ensuring maximum illimination aspect in surrounding garden light 10 Watt inbuilt driver, IP 65 230 V complete connection with PVC insulated multi stranded copper flexible wire twin core of suitable size from nearest source complete all as specified and as directed by Engineer-in- Charge. Make Havells/Surya/Crompton/Phillips.

Supply and fix MCCB having breaking capacity of of 16 KA 415V, 4 pole having rating capacity of 63 Amp 100% ICU complete all as specified and as directed.

Supply and fix MCCB having breaking capacity of of 16 KA 415V, 4 pole having rating capacity of 100 Amp 100% ICU complete all as specified and as directed.

S&F sheet metal enclosure double door concealed suitable for distribution boards when MCBs to be used having 100 Amp rated bus bar SPN DB 8 ways 240 V complete all as specified and as directed .

S&F MCB single pole and neutral 40 Amp/63 Amp 240 V ,10KA , 'C' series, complete all as specified and as directed with copper lugs

S&F MCB single pole 6 to 32Amps 240 V,10KA, 'C' series,complete all as specified and as directed

Supply and fixing in repair 22 W LED 6000k Decorative ultra slim linear LED fitting fixture with extruded polycarbonate ,environmental friendly ,energy efficentinterated driver and 28watts lamp fitted including wiring upto and terminal into ceiling rose complete all as specified and directed by Engr-in- Charge.

Supply and fix LED 35W building security light fitting,5700 K energy saving & environmental friendly long life versatile pressure die cast aluminium IP 66.road way luminare with high power LEDs as light source and electronic driver suitable for pole dia 35 mm including 35 mm dia light grade tube bracket ,bend to shape 1.80 mtr length with two nos of clamps of size 50mm x 6mm with nuts and bolts,washers etcincluding connection with 1.5sqmm threesingle core PVC insulated and PVC sheathed cable stranded copper cable upto ceiling rose and fixing on walls/pole complete all as specified and directed. Make:bajaj cat part noBRLEP20WLEDWH or equivelent of philips/Havells /CG

Supply and laying or fixing or passing through HDPE pipe, 1100 volts grade heavy duty cable with XLPE insulated stranded aluminium conductor served with an inner sheathing of PVC tape armoured with galvanised steel or strip and overall PVC sheathed, 10 sq mm 4 core ISI Marked as per IS 7098(Part 1) including connecting on LT OH line / LT panel /DB with suitable lugs, glands, binding wire etc including taking down complete all as specified and directed.

Supply and laying or fixing or passing through HDPE pipe, 1100 volts grade heavy duty cable with XLPE insulated stranded aluminium conductor served with an inner sheathing of PVC tape armoured with galvanised steel or strip and overall PVC sheathed, 25 sq mm 4 core ISI Marked as per IS 7098(Part 1) including connecting on LT OH line / LT panel /DB with suitable lugs, glands, binding wire etc complete all as specified and directed.

Supply and laying or fixing or passing through HDPE pipe, 1100 volts grade heavy duty cable with XLPE insulated stranded aluminium conductor served with an inner sheathing of PVC tape armoured with galvanised steel or strip and overall PVC sheathed, 35 sq mm 4 core ISI Marked as per IS 7098(Part 1) including connecting on LT OH line / LT panel /DB with suitable lugs, glands, binding wire etc complete all as specified and directed.

S&F storage type water heater (Geyser), 230 Volt AC, 25 Ltrs capacity BEE 5 star rating comprising copper inner tank,suitable heatng element, thermostate with adjustable temperature stting 0-90 C, indication lamps provision for inlet outlet and air vent connections & heavy duty with brass nuts, 450 mm long mounteted on wall surfaces including all fixing arrangement such s faster bolts, nuts washers etc complete including making good disturbed wall surfaces matching with the existing surfaces and finishing all as specified and as directed by Engr-in-charge.

Supply and Fixing Exhaust fans Steel Body AC single phase 230/240V of size 300 mm sweep, 1400 RPM with louvre complete including with all arrangement of making holes on wall, making good and finishing of disturbed surfaces matching with the existing surfaces, necessary fixing arrangement such as fastener bolts, nuts, washers etc, of appropriate size all as specified and as directed

S&F BLDC Ceiling fan complete with three aluminium blades down rod, snackel clamp, reel insulator, fan canopy split pin and accessories 230 V, 1200mm sweep with service value not less than 7.8, power consumption not more than 28 watt and minimum air delivery of 220 CMM, BEE 5 star rated, two core PVC insulated copper wire white sheathed of size 0.5 sqmm from fan connector to ceiling rose complete all as specified and directed. NOTE:-(I) Writing MES no in 20mm letter size with black paint etc is deemed to be included in quoted rate. (ii) Old fan deposit in store yard.

Material and labour for Double wall corrugated HDPE pipe, ISI marked of outer dia 50mm, inner dia 38mm with smooth internal and profiled external surface, non-pressure type, laid in trenches/floors/duct or fixed on walls /pole including all connections, accessories like socket, couplers, bends, etc for protection of LT cable XLPE grade 1100 volts complete all as specified and directed by Engineer-in-Charge.

M&L pipe galvanised iron of size 50 mm dia, light grade ISI marked, complete with fittings laid in trenches/ fixed with poles etc as protection to cables complete as ditrected by Engineer in Charge

M&L for earthing complete with galvanised steel earth plate electrode of size 600 mm x 600 mm x 6 mm thick weithing not less than 17.5 Kg buried directly in ground (earth pit not less than 2.25 mtr deep below normal ground level) with top edge of the plate not less than 1.5 mtr below ground level, connected to galvanized earth lead wire 4.00 mm dia by means of bolts nuts check nuts & washers of galvanized iron or steel , procteded by GI pipe 15 mm bore( light grade) and watering pipe 20 mm bore GI pipe (light grade) and chamber of pcc 1:4:8 type D2 using 40 mm graded stone aggregate and coping shall be in PCC 1:3:6 type C1 using 20mm graded stone agg. 50 mm thick cover of RCC 1:2:4 type B1 using 20 mm graded stone agg. reinforced with 8 mm dia MS tor bar @ 80 mm c/c both ways including excvation and earth work and removal of surplus soil complete all as shown in electrical plate no 3 of SSR PT 1, 2009 with charcoal dust and salt complete and earth lead connected to earthing test point (up to main switches, DBs) complete all as specified & testing on completion. NOTE:- (I) item includes the cost of 7.5 mtr length GI pipe for protection for GI earth wire. (ii) item rates includes the cost of 7.5 mtr earth lead GI earth wire. (iii) PCC pit shall be provided at least 500mm away from the pit and not on the earth pit itself and the extra cost of additional length of watering pipe,bends,elbow etc shall be deemed included in the unit rate.

M/S LAKSHYA CONSTRUCTIONS (BID ID -3491149)

RAVI TRADERS (BID ID -3500727)