ADDITION ALTERATION AND SPECIAL REPAIR TO MFAB BLDG NO 208 OF ELECTRO CHEMICAL ENGINEERING ECE DEPARTMENT AT NAVAL DOCKYARD MUMBAI UNDER GE NW KUNJALI COLABA MUMBAI

Amount

Taking down chowkats or frame with shutter ( without taking off shutter from frame) , n exc 1.5 sqm each complete all as specified and directed by Engr-in-Charge.

All as per item 1 above but exc 1.5 sqm but not exc 4 sqm each complete all as specified and directed by Engr-in-Charge.

Taking down 15mm bore, GI tubing and connections including cleaning for refixing or removal to store complete all as specified and directed by Engr-in-Charge.

All as per item No 3 above but 20 mm bore GI Pipe complete all as specified and directed by Engr-in-Charge.

All as per item No 3 above but 25 to 40mm bore GI Pipe complete all as specified and directed by Engr-in-Charge.

Dismantling 100/75 mm bore, cast iron or reinforced concrete drain pipes, jointed in cement mortar and taking out of trenches if required complete all as specified and directed by Engr-in-Charge.

Demolition of brick work or stone /boulder masonry built in cement mortar, including all quoins, arches, pillars, etc complete all as specified and directed by Engr-in-Charge.

Dismantling wrought iron or mild steel work of any description complete all as specified and directed by Engr-in-Charge.

Dismantling wall and ceiling boards (Fibre, pulp, insulation etc.) or insulation boards/slabs/blankets, any thickness, including cover fillets complete all as specified and directed by Engr-in-Charge.

Dismantling Asbestos cement/fiber reinforced translucent sheet (corrugated, semi-corrugated etc.) sheets in roof covering complete all as specified and directed by Engr-in-Charge.

Dismantling floor hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and directed by Engr-in-Charge.

Taking down cement plaster on brick/ surfaces built in cement mortar including raking out joints, bedding for key scrubbing down with water etc complete all as specified and directed by Engr-in-Charge.

Hacking out old broken glass any thicknesss & size from frames of any description fixed with putty or beads etc complete all as specified and directed by Engr-in-Charge.

Demolition of plain cement concrete of any description and in any position not other wise specifically provided for complete all as specified and directed by Engr-in-Charge.

Demolition of plain cement concrete in ground floors and pavings n exc 15cm thickness (below or above ground level) complete all as specified and directed by Engr-in-Charge.

Roughening Surfaces of old Concrete Floor by picking, sweeping clean and washing down with water to remove dust etc brushing neat cement slurry with 3.0 Kg of cement per Sqm complete all as specified and directed by Engr-in-Charge.

Material and labour for PCC 1:2:4 type B2 using 40 mm graded stone aggregate, as in foundation of poles, filling or mass concrete complete all as specified and directed by Engr-in-Charge.

M& L for 50 mm thick PCC 1:2:4 type B1 using 20 mm graded stone aggregates as in floor finished cement concrete surfaces even and smooth using extra cement complete all as specified and directed by Engr-in-Charge.

Material and labour for brick work with sub class 'B' bricks (old Size) straight or curved on plan exc 6 m mean radius and built in CM (1:6) complete all as specified and directed by Engr-in-Charge.

All as per item No 19 above but half brick thick wall built in CM 1:4 complete all as specified and directed by Engr-in-Charge.

Material and labour for rendering 15 mm thick in CM 1:6 on fair faces of brick work or concrete surfaces finishing the surface fair and even complete all as specified and directed by Engr-in-Charge.

Material and labour for removing loose, disturbed or disintegrated old concrete/brick surfaces of walls, RCC beam, column, lintel, pardi, railing etc, cleaning thoroughly exposed reinforcement, by sand blasting using suitable pump as direceted by the GE, preparing exposed concrete surfaces to receive guniting, applying one coat of anti corrosive paint to the exposed reinforcement, applying pressure guniting in cement mortar 1:3, average thickness 20mm to 30mm and thereafter rendering 10mm thick plaster in cement mortar 1:3, mixed with water proofing compound in the ratio as per the manufacturer'r instructions and finishing the surfaces even and smooth without using extra cement to match with the existing surfaces, removing the debris outside MD land including material and labour and safety arrangement for guniting work, complete all as specified and directed by Engr-in-Charge. (Note:- (i) The finished level of the surfaces shall be matched with the existing surface. WPC shall be measured & paid separately as supply only) (ii) Provision of additional reinforcement steel in case required and ordered shall be measured and paid seperately.

Material and labour for rendering 5 mm thick in CM 1:3 on fair faces of brick work or concrete surfaces in ceiling finishing the surface even and smooth complete all as specified and directed by Engr-in-Charge.

Material and labour for RCC 1:2:4 type B1 using 20 mm grded aggregate as in lintels n exc 1.5m span complete all as specified and directed by Engr-in-Charge.

Supply and fixing mild steel door shutters with and including hinges, locking arrangement, door stoper with provision for fixing of hydraulic door closer. (Hydraulic door closer will be measured and paid separately) complete all as specified and directed by Engr-in-Charge.

Supply and fixing powder coated aluminium frame/shutters for doors, windows, ventilators with one or more rebates, aluminium nosing patti for steps etc. including joining cleat for fixing, locking arrangement, rubber beading, screws, handles, hinges, tower bolts etc. complete all as specified and directed by Engr-in-Charge.

Supply and fixing false ceiling with powder coated exposed GI grid suspension system (E-Grid T-2430 or equivalent load carrying capacity with mid span deflection not exc. 1/360 span with hanger spacing of 1200mm c/c) consisting of main runner 3600mm long, cross Tee 1200mm/600mm long and wall angle. The main runners to be placed @ 1200mm, the cross Tee 1200mm will be inserted in the pre cut slots of main runner at a regular interval of 600mm to form a modular grid of 1200mmX600mm. Additional cross Tees of 600mm shall be placed perpendicular to the cross tee 1200mm long to finally form a grid of 600mmX600mm. Grid of modular size 600mmX600mm shall be supported by 4mm dia G.I. wire from purlins/soffit with and including 4mm thick high pressure steam cured non asbestos fiber cement designer ceiling board (Density>1200Kg/Cum) of size 595mmX595mm, confirming IS 14862 & Type B Category III of ISO 8336, tested as per AS 1530 part 3 & BS-476 Part 4, 5, 6, 7 & 8,complete all as specified and directed by Engr-in-Charge.

Supply and fixing 8 mm thick non asbestos fibre cement building fixed or laid/ inserted to timber/GI/Aluminium framework with counter sunk screws finish with jointing compound and jointing tape as per manufacturer' instructions complete all as specified and directed by Engr-in-Charge.

Supply and fixing 12 mm thick Medium density fibre board, exterior grade, fixed to timber/ Aluminium frame work with screws complete all as specified and directed by Engr-in-Charge.

Material and labour for aluminium anodized grill with suitable aluminium anodized frame of F/H section with suitable fixing screws/attachment etc complete all as per M/S Deco Grill Design No DG -102 , 7.5mm size grill i.e. made out of 75mm thick aluminium plate all as per manufacturer's specifications complete all as specified and directed by Engr-in-Charge.

Supply and fixing Decorative laminate 1.50 mm thick, type 1, of surface finish, colour and pattern as approved, fixed with approved adhesive as per maker's instructions complete all as specified and directed by Engr-in-Charge.

Supply and fixing 5.5 mm thick sheet glass, ordinary quality, in any size of pane complete all as specified and directed by Engr-in-Charge.

Supply and fixing in repairs Sun control film, 50 micron non reflective type,sticked to glass as per manufacturers instructions complete all as specified and directed by Engr-in-Charge.

Supply and fixing for 2nd class hard wood plain, solid, straight chowkats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints complete all as specified and directed by Engr-in-Charge.

Supply and fixing 40mm thick flush shutters, solid core construction, with block board core and ply wood face panels, commercial type on both side complete all as specified and directed by Engr-in-Charge.

Supply and fixing Aluminium anodised sliding door bolt 300m long, with hasp, staple (bolt type) and fixing clip of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy complete all as specified and directed by Engr-in-Charge.

Supply and fixing rolled mild Steel butt hinges 100mm size complete all as specified and directed by Engr-in-Charge.

Supply and fixing aluminium anodised Barrel tower bolts of extruded section, length of bolt 200mm complete all as specified and directed by Engr-in-Charge.

Supply and fixing extruded aluminium anodised alloy handles, fabricated type 150mm size complete all as specified and directed by Engr-in-Charge.

Supply and fixing Door closer, Aluminium (die cast) body,hydraulically regulated, designation No. 3, unversal type suitable for door shutters of 851 to 1000mm in width and of weight between 61 to 80 Kg complete all as specified and directed by Engr-in-Charge.

Material and labour Material & labour for water proofing plaster for sunken portion in CM 1:3, 15 mm thick in two coats with integral water proofing compound at the rate of 3 % by weight of cement and finishing the surface even and smooth without using extra cement complete all as specified and as directed by Engineer-in-Charge

Material and labour for water proofing treatment of sunken floor / wall surfaces by applying two coats of elastomeric coatings of BRUSHBOND RSX in FOSROC or TECKFORCE 2K STRONG in CHOWKSEY CHEMICALS as a two component flexible elastomeric coating with minimum 2mm thickness layer complete as per manufacturer’s instruction’s complete all as specified and directed by Engr-in-Charge.

Material and labour for PCC 1:7:12 type F2 using 40 mm graded stone aggregate as in filling (sunken portion). etc complete all as specified and directed by Engr-in-Charge.

Supply and fixing Vitrified ceramic tiles 10mm thick (square/rectangular) area of each tile exceeding 0.36 sqm but not exceeding 0.42 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of the tiles with and including 20mm thick screed bed in CM 1:4 complete all as specified and directed by Engr-in-Charge.

Material and labour for Non skid coloured ceramic tiles 7 to 8 mm thick ( square/rectangular) area of each tile exceeding 0.18sqm but not exceeding 0.38 sqm, in floors etc. set and jointed in neat cement slurry and pointed in coloured cement to match the shade of the tiles with and including 20mm thick screed bed in CM 1:4 complete all as specified and directed by Engr-in-Charge.

Material and labour for Coloured glazed ceramic tiles in vertical surface 450X350X7mm thick , set and jointed in neat cement paste and pointed in coloured cement to match the shade of the tiles with and including 10 mm thick backing coat in CM 1:3 complete all as specified and directed by Engr-in-Charge.

Material and labour for 20-25mm thick, machine cut, Kota stone slab, as in floors, steps, landing etc. set and jointed in neat cement slurry and pointed in coloured cement to match the shade of slab, including cutting, polishing etc. with and including 20mm thick screed bed in CM 1:4 complete all as specified and directed by Engr-in-Charge.

All as per item 47 above but as in skirting/ riser/ dado etc with and including 10 mm thick backing coat in CM 1:3 complete all as specified and directed by Engr-in-Charge.

Extra over Kota stone slabs for edge polishing/ chamfering/ noising/ grooves/ bevelling etc complete all as specified and directed by Engr-in-Charge.

Material and labour 20 mm thick Granite stone slab ( of any type) work ( table rubbed and polished) in steps, risers, jambs, pillars, window cills, cooking plateforms and like in cemnet mortar ( 1:4) including pointing in white cemnet (1:2) using marble dust with admixture of pigment to match with shade of granite complete all as specified and directed by Engr-in-Charge.

All as per item no.50 above but as in floor comlete all specified complete all as specified and directed by Engr-in-Charge.

Supply and fixing in repair white vitreous china squatting pan, 'orissa' pattern, water closet of size 580x440mm with integral foot rest, P/S trap etc complete all as specified and directed by Engr-in-Charge.

Supply and fixing in repairs white vitreous china washed down water closet pan, (pedestal pattern), white, with and including P/S trap, PVC solid type seat cover etc complete all as specified and directed by Engr-in-Charge.

Supply and fixing vitreous china urinals,half stall type, flat back, white, with grating and union for discharge pipe, complete including providing and fixing plugs, bedding urinal against wall in CM 1: 2, securing urinal to plugs with and including 60 mm long brass screws, pointing around urinal back in cement , fixing automatic flushing cistern with brackets, flush pipe, grating and Union for discharge pipe.(Exclusive of fixing supply pipe to flushing cistern , trap and waste pipe) complete all as specified and directed by Engr-in-Charge.

Supply and fixing white glazed vitreous china wash hand basin of size 550x400mm with and including CI brackets, 32mm bore brass CP waste fitting, Inlet/ outlet, PVC flexible pipe, 600mm size for 15 mm bore pipe with PTMT nut and washers etc complete, fixed in repairs complete all as specified and directed by Engr-in-Charge.

Supply and fixing vitreous china urinal partitions white of size 310X700mm, slabs, terminating about 40 cm above floor line, fixed in repairs complete all as specified and directed by Engr-in-Charge.

Material and labour PVC SWR floor trap 75mm, plain with grating including setting and jointing with solvent cement complete all as specified and directed by Engr-in-Charge.

Supply and fixing 15 mm dia medium grade galvanized steel tubing with all fittings fixed to walls, ceilings or laid under floors complete all as specified and directed by Engr-in-Charge.

All as per item 58 above but 20 mm bore pipe complete all as specified and directed by Engr-in-Charge.

All as per item 58 above but 40 mm bore pipe complete all as specified and directed by Engr-in-Charge.

Cutting chases in brick work for concealed water tubing and making good, cutting exc 10 cm but nexc. 20 cm girth complete all as specified and directed by Engr-in-Charge.

Supply and fixing 110mm dia PVC ( SWR) grade pipes, single socketed in any length with rubber ring joints fixed to walls with and including fixing clips complete all as specified and directed by Engr-in-Charge.

All as per item No 62 above but laid in floors/trenches complete all as specified and directed by Engr-in-Charge.

Supply and fixing 75mm dia PVC ( SWR) grade pipes single socketed in any length with rubber ring joints fixed to walls with and including fixing clips complete all as specified and directed by Engr-in-Charge.

All as per item No 64 above but laid in floors/trenches complete all as specified and directed by Engr-in-Charge.

Supply and fixing 110mm dia PVC ( SWR) grade single/double T/Y, bends etc. with or without access doors including fixing clips complete all as specified and directed by Engr-in-Charge.

All as per item No 66 above but 75mm dia complete all as specified and directed by Engr-in-Charge.

Supply and fixing 100mm dia PVC ( SWR) grade pipes single socketed in any length with rubber ring joints fixed to walls with and including fixing clips, bends, elbow, shoes bends etc complete all as specified and directed by Engr-in-Charge. (Note:- Measurment shall be taken along the centre line of the pipes.)

Supply and fixing 15 mm bore dia of pipe, brass chromium plated fancy type bib tap, fixed in repairs complete all as specified and directed by Engr-in-Charge.

Supply and fixing in repairs 15mm size Stop Valves fancy type chromium plated screwed down high pressure with crutch or butterfly handle handle screwed both ends complete all as specified and directed by Engr-in-Charge.

Supply and fixing in repair 15 mm dia fancy type pillar tap cast copper alloy with capston heads chromium plated screwed down high pressure with or without hot or cold with long screws shanks and fly nuts screwed for iron pipes complete all as specified and directed by Engr-in-Charge.

Supply and fixing Concussive push button taps of cast copper alloy, screwed for PPR pipe 15mm bore and fixed in repairs complete all as specified and directed by Engr-in-Charge.

Supply and fixing PVC Connections 15mm size with PTMT nuts of length 600mm complete all as specified and directed by Engr-in-Charge.

Supply and fixing brass chromium plated shower rose 125mm size, fixed in repairs complete all as specified and directed by Engr-in-Charge.

Supply and fixing 10 litres capacity PVC low level flushing cistern of approved make including ball valve,syphon set, inlet and outlet pipe complete all as specified and directed by Engr-in-Charge.

Supply and fixing brass chromium plated, tubular towel rail 20mm dia, D type, 60 cm long between flange, fixed in repairs complete all as specified and directed by Engr-in-Charge.

Material and labour for preparation of old painted wooden surfaces of any description over 10cm width or girth and applying one coat of synthetic enamel paint complete all as specified and directed by Engr-in-Charge.

Material and labour Two coats of synthetic enamal paint over a coat of pink primer on newly wood/wood based surfaces over 10cm width or girth incl preparation of new surface complete all as specified and directed by Engr-in-Charge.

Material and labour for preparation of old painted steel surfaces of any description not otherwise over 10 cm in width or girth and applying one coat of synthetic enamel paint complete all as specified and directed by Engr-in-Charge.

Material and labour Two coats of synthetic enamal paint over a coat of redoxide primer steel surfaces over 10cm width or girth incl preparation of new surfaces complete all as specified and directed by Engr-in-Charge.

Material and labour for complete removal of existing treatment on wall surfaces and applying one coat of Birla white wall care putty, sanding the surfaces till even and smooth finish and applying one coat of wall primer and finally applying two coats of oil bound distemper of approval tint complete all as specified and directed by Engr-in-Charge.

Material and labour for preparation of newly plastered surfaces of wall & ceiling applying two coats of oil emlusion distemper over a coat wall care putty of 3mm thick and alkali primer complete all as specified and directed by Engr-in-Charge.

Material and labour for preparation of old plastered or unplastered decorated surfaces of wall including cornices, pillasters etc and applying one coat of white wash on walls complete all as specified and directed by Engr-in-Charge.

All as per item No 84 above but in ceiling complete all as specified and directed by Engr-in-Charge.

Material and labour for applying 3mm thick one coat wall care putty on walls / ceilings etc complete all as specified and directed by Engr-in-Charge.

Material and labour for Preparation of old decorated surfaces of wall over 10cm width or girth and stopping of painted surface and applying one coat of plastic emulsion paint on walls complete all as specified and directed by Engr-in-Charge.

Material and labour for Preparation of old decorated surfaces of wall over 10cm width or girth and stopping of painted surface and applying two coats of plastic emulsion paint on walls complete all as specified and directed by Engr-in-Charge.

Material and labour for preparation of newly plastered wall surfaces, over 10cm girth, applying two coats of 100% acrylic, weather resistant emlusion over a coat of exterior wall primer complete all as specified and as per manufacturer's instruction complete all as specified and directed by Engr-in-Charge.

Complete removal of existing treatment of walls and applying two two coats of acrylic (antifungal) exterior grade paint of over one coat of primer on wall/roof including scaffolding complete all as specified and directed by Engr-in-Charge.

Complete removal of existing water proofing treatment of any description (i.e PCC including screed bed and membrane including PCC tiles of any size in roof area) in any position including cleaning, wire brushing, watering, removal of deris upto 1500 mtr distance complete all as specified and directed by Engr-in-Charge.

Material and labour PCC (1:2:4) type B-1 (Using 20mm graded stone aggregate) as in roof/chajja padding for maintaining roof/chajja slope complete all as specified and directed by Engr-in-Charge.

Material & labour for the roof surface thoroughly wire brushed, washed and dried up and cleaned of all foreign matter and dust to receive bituminous primer, apply bituminous oil based cold applied primer @ 270 to 300 gms/ Sqm manufactured by the same agency as that of APP all as per manufacturers instructions. Laying 5 layered, 3 mm thick APP (A woolen propylene) modified membrane reinforced with 180 GSM (Gms/ Sqm) of non woven polyester mat, applied by thermo fusion using LPG torch on the bottom portion of the membrane with an overlap of 75mm in longitudinal direction & aluminium paint over it complete all as specified and directed by Engineer-in-Charge. application permissible Note :- (company authorised application only permissible to the concerned site and applicator certificate to be submitted to the concerned office)

Material and labour for burshing neat cement slurry with 3 Kg of cement per square meter complete all as specified and directed by Engr-in-Charge.

Material and labour for rendering 20mm thick cement plaster in CM (1:3) on roof top surface finished even and fair including WPC by weight of 3% of total cement concrete complete all as specified and directed by Engr-in-Charge. Note : WPC will be measuerd separately.

Supply only integral water proofing compound complete all as specified and directed by Engr-in-Charge.

Material and labour for cement concrete tiles 30Cmx30Cmx22 mm thick, machine pressed, (with grey cement & pigments) set jointed and pointed in neat cement slurry in floors over and including 15mm thick bedding layers in CM 1:3 all as specified & directed by Engr-in-Charge.

Material and labour for taking down , chipping and removing the loose, spailt, damaged cement concrete, cement mortor surfaces of RCC Columns, beams, walls, chajjah etc and exposing the reinforced cement , wire brushing and cleaning the exposed steel reinforced bar, applying rust remover over the cleaned re-bar surface wash the re-bar with clean water for removing all rusts from the old re-bar surfaces, fixing new reinforcement for strengthen the members as required, applying two coats of epoxy zinc primer on new and old steel surfaces, saturate the substrate with water applying one coat of polymer modified bond coat on affected concrete surfaces and finally providing polymer modified cement and quartz sand mortor in CM 1:3 mix , 40mm thk in two coats, using polymer @ 10 to15% by weight of cement complete all as specified and directed by Engr-in-Charge. Note :-(New reinforcement and MS Sections will be measured and paid separately)

Material and labour for 1:3:6 type C0 for 12.5mm graded aggregate) providing precast cement concrete louvres and jallies, 25mm thick (mea sured solid), including all mould- ings but excluding framed all as specified and directed and Note :- Pre cast frame shall be measured and paid seperately

Material and labour for TMT mild steel bars,10 mm dia and over, cut to length bent to shape required, including cranking bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips quality complete all as specified and directed by Engr-in-Charge.

All as per item No. 100 above but 5mm dia and over up to and including 10mm as in stirrups complete all as specified and directed by Engr-in-Charge.

Material and labour Hard drawn steel wire fabric cut to lengths, bent to shape required and tying with and including mild steel wire (annealed) not less than 0.9mm in dia supplied and fixed in reinforcement not exceeding 4kg per sqm complete all as specified and directed by Engr-in-Charge.

Supply and fixing laying chiken wire mesh of galvanised stell expanded metal, cut to length, and tying with and including annealed mild steel wire not less than 0.9mm dia or fixing with galvanised steel staples supplied and fixed complete to wood or steel members all as speicified and directed by Engr-in-Charge.

Supply and fixing 4mm dia galvanised steel wire, 150x100mm mesh, made up into matteresses or cages, lapped, wired and laid in position, including closing after filling complete all as specified and directed by Engr-in-Charge.

Supply and fixing for rolled mild steel Sections of Grade Fe 410-W, (Gde- E-250) quality-A, as in post, runners, rafters, purlins steps etc fixed with connecting plates including bending, welding etc complete all as specified and directed by Engr-in-Charge.

All as per item No. 105 above but MS Plates ( plain or chequered) complete all as specified and directed by Engr-in-Charge.

Supply and fixing for rolled mild steel Sections of Grade Fe 410-W, (Gde- E-250) quality-A, as in Stairs (framed) including stringers, treads, landing, balusters, hand rails etc, including cleats, brackets, etc. complete all as specified and directed by Engr-in-Charge.

Supply and fixing Steel work in tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to IS 1161-1979 grade St.-240 complete all as specified and directed by Engr-in-Charge.

Supply and fixing Steel door including projecting type hinges, steel handle, complete, with glazing bars, dovetailed or welded complete all as specified and directed by Engr-in-Charge.

Supply and fixing pre-painted galvalume aluminium zinc coating GI baseds corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed by Engr-in-Charge.

All as per item No. 110 above but plain galvalume sheets for ridges/ Flashings complete all as specified and directed by Engr-in-Charge.

Removing debris exc. 1.50 Km but n exc. 25 Km and depositing where directed, in soil outside MD land complete all as specified and directed by Engr-in-Charge.

Supply and fixing for providing and erecting at site self supported steel H- Frame Scaffolding only for structural repairs of column with micro concerte or columns jacketing with cross bracings of good quality without dents and corrosion to reach place of work including approchases, extensuion, working platform ladders, lifting tackel necessary wall anchores for men and materials till completion of all structural repair items of work and curring period etc. complete. The work should be caried out with all the safety belt and adequate labour insurance under the supervision of qualifed supervisor this item should be used only for structural repair work for entire period of building. (Payment should be only once irrespective of duration of scaffolding.) etc.complete all as specified and directed by Engr-in-Charge.

Supply and fixing for providing and fixing 6mm thick plywood covering panels in pattern upto 30m height as per the directions of Engineer-in-charge with necessary backing framework to shield windows etc. from falling debris and removing and taking away the material after completion of work (the covering material will be the property of contractor after completion of work) including making good any incidental damage(s) to the existing building or its finishes etc complete. (The measurements for payment shall be made in terms of the area protected by such covering). Only one weightage will be given for covering windows till finishing irrespective of time-period of protection complete all as specified and directed by Engr-in-Charge.

Material and labour for breaking carefully the loose concrete of distressed member without damaging existing strong concrete by means of sharp chisel which should tempered regularly of high frequency low impact hammer is used, cleaning the surface by water jet pressure pump at 4 to 5 kg/ sq.cm pressure to remove chlorides and loose partials, air drying the surface etc. The work should be carried out with all the safety measures like helmet, safety belt and adequate labor insurance under the supervision of qualified supervisor. (The damaged ceiling / concrete will be measured) etc.complete all as specified and directed by Engr-in-Charge.

S& F for providing and erecting steel tubular props of required height up to 14' feet, L head or flat head braced at center and supporting a continuous 2"X 3" wooden runner , resting on wedge and block minimum capacity 3 Ton to support the structure provisionally during repair and jacketing etc. and maintain them in position till required item etc. complete. The props are erected in perfect vertical in plumb taking /transferring the load equally/ uniformly. The location of every prop should be one over another floor and it should not be eccentric. The tightening of every prop should be uniform to all props to strain the building uniformly, removing the same as and when directed by structural engineer/ site Engineer. The work should be carried out with all the safety belt and adequate labour insurance under the supervision of qualified supervisor and remove the same completion of work etc.complete all as specified and directed by Engr-in-Charge.

Supply and fixing for cleaning the existing reinforcement with hammer tapping and wire Brush/ rotary wire brush , fixed to hand drill machine, making the surfaces free form loose corrosion material, dirt scaling etc. complete. Applying two coats of polymer based alkaline rust converting primer confirming to ASTM-B 117 by means of paint brush, liberally all over in two coats of 1 hour between the costs, The product should converts the rust in to stable organo metallic complex molecule layer, this should also act as primer to further treatment of steel etc. complete. The work should be carried out with all the safety belt and adequate labour insurance under the supervision of qualified supervisor. (the damage celling/ concrete al be measured) etc. complete all as specified and directed by Engr-in-Charge.

Supply and fixing for anticorrosive treatment to Reinforcement application of two coats of IPNETRB (CBRI known how) on expose reinforcement in two coats with time interval) of minimum 4 hours between each coat. The application shall be by brush, Application is allowed to dry for further treatment. The work should be carried out with all the safety measures like helmet, safety belt and adequate labour insurance under the supervision of qualified supervisor. (The damage ceiling / concrete all be measured) etc. complete all as specified and directed by Engr-in-Charge.. Make: Fosroc, Sika, Dr fixit or as approved by GE

Material and labour for providing and applying two coats of concrete penetrating hi- tech corrosion inhibition mechanism inhibits corrosion of steel in concrete at the poles, cathode & anodic simultaneously on concrete surface which is prepared earlier. The work should be carried out with all the safety measures like helmet, safety belt and adequate labour insurance under the supervision of qualified supervisor. (The damage ceiling/ concrete all be measured) etc. complete. Make: Fosroc, Sika, Dr fixit or as approved by GE

Supply and fixing for replacing distressed / loose/ cracked/ porous carbonated, loose part of concrete and repairing the damaged surface of concrete , fix the form work/ structural element, pour the free flow ready mix micro concrete mix with 51 to 7 1t of water in the form work. Micro concrete should be mixed in steel tray homogeneously makeup concrete is based on types of structural element and its location. The work should be carried out with all the safety measures like helmet, safety belt and adequate labour insurance under the supervision of qualified supervisor etc. complete all as specified and directed by Engr-in-Charge.. Make: Fosroc, Sika, Dr fixit or as approved by GE

Supply and fixing for providing and applying 15 mm thick polymer mortar to load carrying R.C.C member in two layers in proportion of 1:5:15 by weight polymer of approved quality and make, cement and wash quartz sand with required W.C. ratio for desired floating, curing after initial setting time etc. complete all as specified and directed by Engr-in-Charge. Make: Fosroc, Sika, Dr fixit or as approved by GE

Supply and fixing for making up lost section of concrete / mortar with thixotropic repair mortar is one component thixotropic dual shrinkage compensated fiber reinforcement formulation for structural members. Build up section by hand packing as per manufacturers specification, applied by mean of hand glouse by expert applicator, the rehabilated surface should be free from air gaps, voids should be in line with existing required line and line with existing surface, including curing, cleaning the area etc. complete. The work should be carried out with all the safety measures like helmet, safety belt and adequate labour insurance under the supervision of qualified supervisor etc. complete all as specified and directed by Engr-in-Charge. Make: Fosroc, Sika, Dr fixit or as approved by GE

Supply and fixing for providing and Fixing Shear connectors of 8mm dia. HYSD steel with two component, styrene & cement free, epoxy-acrylate fixing and anchoring compound supplied in self mixing Cylinder-in-cartridge form that avoids site mixing using standard sealant applicator gun after drilling holes of 12mm diameter to a minimum depth of 100mm at required locations, inclusive of all material, manpower and equipment complete all as specified and directed by Engr-in-Charge.

Material and labour for providing and applying approved epoxy resin EPI Bond of Krishna conchem or equivalent before polymer plaster/ concrete to have the perfect bond between old concrete and new concrete/ polymer plaster surface confirming to ASTM-C- 882-87 using nylon brushes scaffolding labour etc. complete all as specified and directed by Engr-in-Charge. Make: Fosroc, Sika, Dr fixit or as approved by GE

Material and labour for providing and applying priming cum bonding coat of polymer of approved make and quality as approved by engineer- in - charge and cement slurry in 1:1 proportionate by weight to concrete area by brush or any other established method etc. complete all as specified and directed by Engr-in-Charge. Make: Fosroc, Sika, Dr fixit or as approved by GE

Material and labour for drilling and fixing Teflon perforated nozzles in RCC member, including drilling 14 mm dia. 50 to 100mm deep holes in structural members at in cle the intervals of 600 mm in staggared manner of as directed by the consultants in RCC structural elements. Clean the holes by air blower prior to fixing nozzles. fixing of nozzels in cleaned holes. external end of nozzles to be machined to receive outlet of grouting gun. nozzel is fixed by means of epoxy by means of epoxy sealent to ensure complete sealing . cure the system for min. 12 hours. the work should be be carried out with all the safety measures like like helmet, safety belt and adequate labour insurance under the supervision of qualifed supervisor. etc . complete all as specified and directed by Engr-in-Charge.

Material and labour for providing and Injecting the fixed packer two-component low viscosity (<350 cps) epoxy resin system that achieves compressive strength in excess of 55 MPa at 1 day & 65 MPa at 7 days. and shall exceed 15 MPa in slant shear bond strength with minimum pot life of 30 minutes at ambient temperatures complying with ASTM C881, Type 1 & 4, Grade 1, Class B &C using any of the standard pressure grouting methods at a maximum pressure of 2kgs/sq.cm. till refusal and allowing the epoxy grout to cure before removal of packers inclusive of cost of Material, Manpower and Equipment. complete all as specified and directed by Engr-in-Charge. Make: Fosroc, Sieka, Dr fixit or equivalent

Material and labour for providing and Injecting high performance non shrink, free from high strength antiwash Polymer Cement Grout of Krishna Conchem or equivalent by addition of water as per manufacturers specification into hoeycombing area/ porous concrete including drilling of holes minimum 50 mm in concrete, fixing nipples, injecting grout by suitable pump at pressure of 2.0 kg/cm2 and subsequently cutting/ removal of nipples and sealing of holes with epoxy putty EPW 1010 etc.complete all as specified and directed by Engr-in-Charge. Make: Fosroc, Sieka, Dr fixit or equivalent

Supply and Fixing shower (health Faucet) with 1M long flexible tube with wall hook Chrome Plated (Make- Jaquar Cat No. ALD-CHR-593 & SHA-571 or equivalent as approved by GE).

Supply and Fixing 15mm bore brass both way bib use for health fucesets taps cast copper alloy with crutch or butterfly handle screwed down, screwed for iron pipe or for brass ferrule and fixed (weight not less than 1200gms) complete all as specified and directed by Engr-in-Charge

Taking down carefully old U/S point wiring copper/Aluminum (light/ fan /sockets/power) complete with switches, sockets, ceiling roses, lamp holders, brackets & other fitting & Fixtures connected, and making good to disturbed surfaces as directed by Engineer-in-Charge

Taking down carefully sub main wiring including batten/ conduit by unscrewing from wall,ceiling and making good surfaces to match with original status complete all as specified and directed by Engr-in-Charge.

Material and labour point wiring complete with 1.5 Sq.mm single core multistranded PVC insulated & unsheathed copper conductors cable 1100 volts FRLS grade ISI make and drawn through & including PVC non metallic conduit ,concealed with Accessories fixed on wall/ceiling/truss etc with PVC non metallic ISI make terminal boxes fixed on wall including one PVC insulated & unsheathed multistranded copper conductor 1.5 Sq. mm as earth continuity conductor connected to common earth dolly complete all as specified and directed by Engr-in-Charge.

One light point controlled by one 5A switch

One Fan point controlled by one 5A switch

One Exhaust fan point controlled by one 5A switch

One 5A flush type switch socket point on same board board

One 5A flush type switch socket point on independent board

All same as per item No.131 above but of stair case light point controlled by 2 Nos of 2 way swiches for stair case wiring complete all as specified and directed by Engr-in-Charge.

Material and labour point wiring complete with 2.5 Sq.mm single core multistranded PVC insulated & unsheathed copper conductors cable 1100 volts FRLS grade ISI make and drawn through & including PVC non metallic conduit with Accessories fixed on wall/ceiling/truss etc with PVC non metallic ISI make terminal boxes fixed on wall including one PVC insulated & unsheathed multistranded copper conductor 2.5 Sq. mm as earth continuity conductor connected to common earth dolly for15 amp swich socket on independant board complete all as specified and directed by Engr-in-Charge.

Material and labour for point wiring (Work station for computer)complete with proper clour coding using PVC insulated unsheathed multistranded copper conductor cable 4.0 sqmm size, 1100 volts ISI marked, FRLS grade drawn through and including non metalic rigid, double lock, ISI marked, not less than 25mm conduit with all accessories such as tee, bends, elbow, reducers, junction box etcfixed on wall/ceiling/truss and one run of PVC insulated unsheathed, multistranded copper conductor cable of 2.5sqmm size, 1100 volts, ISI marked, FRLS grade green colour as earth continuty conductor connected to common earth dolly with and including modular box with cover plate frame in any module ( Make : schneider elect/legrand mosaic/anchor ave) complete necessary electric connection for each workstation point comprising of 03 Nos 6A sockets and 01 No 15A socket on same board complete all as specified and directed. Note: (a) Colour coding shall be folowed as (i) Phase- Red (ii) Neutral - Black (iii) Earth - green

Material and labour for point wiring 1.5 sq mm FRLS Copper cable 1100 volt grade drawn in and including stove enamelled steel ERW conduit not less than 19mm dia including spacers, saddles, screws etc & 1.5 sqmm PVC insulated copper earth wire including including connected to flame proof switches/sockets etc on indepaendant complete all as specified and directed by Engr-in-Charge.

Material and labour point wiring with 4 sqmm PVC insulated and sheathed copper cable 1100V grade multistranded drawn in and including stove enameled steel conduit not less than 20 mm on wall / ceiling with tee bend, elbows, junction box etc with provn of PVC insulated, 2.5 sqmm copper conductor cable as earth continuity including connected to flame proof switches etc on indepaendant complete all as specified and directed by Engr-in-Charge.

Supply and fixing Flame proof - weather proof switch socket & plug combined 16 A,250 V(2P+Earth) complete all as specified and directed by Engr-in-Charge.

Supply and fixing in replacement of Flame Proof Switch rotary type with termination box in LM6 single pole 250 V complete all as specified and directed by Engr-in-Charge.

Supply and fixing in replacement of 2x 20 watt Fiamma I Cimr certified LED flameproof batten suitable for twin T8 tube of 8 watt IP 65 Protection complete all as specified and directed by Engr-in-Charge. Make -CG,Cat part no-EXTN2LT8-16/20 or as approved of GE

Supply and fixing in replacement of Switch piano flush type single pole one way ,5/6 Amps complete all as specified and directed by Engr-in-Charge.

Supply and fixing switch piano flush button, single pole Two way 5 Amps, 230V complete all as specified and directed by Engr-in-Charge.

Supply and fix switch sockets combination 5 pin 5 Amps flush type 240 Volts AC complete all as specified and directed by Engr-in-Charge.

Supply and fix in replacement switch socket combination multi purpose 3 pin 15 Amps controlled by one switch flush type 240 Volts AC complete all as specified and directed by Engr-in-Charge.

Supply and fixing in replacement of fan regulator electronic step type socket size and making all necessary connections complete all as specified and directed by Engr-in-Charge.

Supply and fixing in replacement of Ceiling rose, PVC/polycarbonate insulated body type, 3 terminal, 240 volts, 5 Amps complete all as specified and directed by Engr-in-Charge.

Supply and fixing in replacement 20 Amps Single pole and neutral enclosure with a two pin and earth plug and socket complete with one single pole MCB.make -Legrand Cat part no -507814,siemens ,GE

Supply and fixing in replacement of 20 Watt 4 FT LED tube light fitting integrated Batten T5: Nakshatra series indooor light decorative alluminiumextruded T5 LED Batten-integrated type. Make- C & S CAR PART NO LTTB4F20WLED/W,OR Equivalent in Havells,CG, BAJAJ

Supply and Fixing in replacement of Ceiling light 36 WATT-2ft X 2 ft Recess mounting led ultra slimceiling light with extruded aluminium housing and milky diffuser.LED ultra slim panel:CYGNUS SERIES.make- CG Cat part no-LCTLRP-36-FO-CDL,C&S CAT PART NO-LTCRSLM36WATT2X2 OR Equivalent in Havells,CG, BAJAJ

Supply and fix 36W powder coated LED security light aluminium die cast body, including making connection complete all as specified and directed by Engr-in-Charge.

S &F in Replacement of 120 WATT LED high/midbay:corvus series intergral industrial high power LED High/midbaywith pressuredie cast alluminium housing anodrisedaluminium reflector,complete with all acessories.make-C&S CAT PART NO-LTEHB120WHPLED/LS,OR Equivalent in Havells,Bajaj,CG

Refixing old unserviceable LED Highbay Light,at any Height complete all as specified and directed by Engr-in-Charge.

Refixing only old serviceable of Ceiling light 36 WATT-2ft X 2 ft Recess mounting led light fitting complete all as specified and directed by Engr-in-Charge.

Supply and fixing in replacement of MCB 6 to 40 Amps capacity, C Curve type suitable for 240 volts AC supply, SP with over load and short circuit protection and rupturing capacity not less than 10 KA including making connection complete all as specified and directed by Engr-in-Charge.

Supply and fixing in replacement of MCB,SPN 40 Amps capacity, C Curve type suitable for 240 volts AC supply, SPN with over load and short circuit protection and rupturing capacity not less than 10 KA including making connection complete all as specified and directed by Engr-in-Charge.

Supply and fixing in replacement of MCB,SPN 63 Amps capacity, C Curve type suitable for 240 volts AC supply, SPN with over load and short circuit protection and rupturing capacity not less than 10 KA including making connection complete all as specified and directed by Engr-in-Charge.

Supply and fixing in replacement of MCB, 4 Pole, 63Amps capacity, C Curve type suitable for 415 volts AC supply, SP with over load and short circuit protection and rupturing capacity not less than 10 KA including making connection complete all as specified and directed by Engr-in-Charge. .make legrand Cat Part no-408702 Equivalent in Siemens,GE

Supply and fixing in repair Distribution Board double door, prewired type, made out of CRCA mild steel sheet surface with insulated material like polyester or with epoxy powder coating and IP 54 & IK 09 protection surface mounting SPN 8 way, 240 volts with bus bar rating 200 Amps, dust and vermin proof suitable for incorporation of MCB’s and isolators etc complete all as directed. Make - Legrand cat No 607731 or equivalent in siemens/GE (Note : The cost of removing old wooden box and making good of surface i.e. brick work, plastering etc is included in quated rate)

Supply and fixing in repair Distribution Board double door, prewired type, made out of CRCA mild steel sheet surface with insulated material like polyester or with epoxy powder coating and IP 54 & IK 09 protection surface mounting SPN 4 way, 240 volts with bus bar rating 200 Amps, dust and vermin proof suitable for incorporation of MCB’s and isolators etc complete all as directed. (Note : The cost of removing old wooden box and making good of surface i.e. brick work, plastering etc is included in quated rate)

Supply and fixing in repair Distribution Board double door, prewired type, made out of CRCA mild steel sheet surface with insulated material like polyester or with epoxy powder coating and IP 54 & IK 09 protection surface mounting TPN 8 way, 440 volts with bus bar rating 200 Amps, dust and vermin proof suitable for incorporation of MCB’s etc complete all as directed. Make - Legrand cat part no 607735 or Equivalent in siemens/GE (Note : The cost of removing old wooden box and making good of surface i.e. brick work, plastering etc is included in quated rate)

Material and labour in repair Submain wiring with two run 4 Sqmm single core multistranded PVC insulated & unsheathed copper conductors 1100 volts FRLS grade ISI make drawn through & including PVC non metallic conduit concealed with Accessories fixed on wall/ceiling/truss etc including one run PVC insulated & unsheathed multistranded copper conductor 4Sq. mm FRLS grade ISI make as earth continuity conductor connected to common earth as earth dolly complete all as specified and directed by Engr-in-Charge.

Material and labour Submain wiring with two run 6 Sqmm single core multistranded PVC insulated & unsheathed copper conductors 1100 volts FRLS grade ISI make drawn through & including PVC non metallic conduit with Accessories fixed on wall/ceiling/truss etc including one PVC insulated & unsheathed multistranded copper conductor 6.0 Sq. mm FRLS grade ISI make as earth continuity conductor connected to common earth as earth dolly

Supply and lay in repair cable XLPE Insulated screened PVC bedded, galvanized steel strip or wire armored, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 35 sq mm 3.5 core. laid in duct / along pole/wall etc including making connection complete all as directed. Note : 1. The cost of Al thimbles/lugs and cable gland etc is incl in quoted rate and no extra payment will be made for it.

Supply and lay in repair cable XLPE Insulated screened PVC bedded, galvanized steel strip or wire armored, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 50 sq mm 3.5 core. laid in duct / along pole/wall etc including making connection complete all as specified and directed by Engr-in-Charge. Note : 1. The cost of Al thimbles/lugs and cable gland etc is incl in quoted rate and no extra payment will be made for it.

Taking down of ceiling fan/Exhaust fan/wall fan, any sweep/size at any height and Refixing complete after Refixing complete all as specified and directed by Engr-in-Charge.

M &L Painting of ceiling fans, complete, in situ with synthetic enamel paint by spraying including filling cavities with filler, one coat after cleaning all dust etc complete all as specified and directed by Engr-in-Charge.

M &L Painting of Exhuast fan , complete, in situ with synthetic enamel paint by spraying including filling cavities with filler, one coat after cleaning all dust etc complete all as specified and directed by Engr-in-Charge.

M &L Painting of ,wall fan complete, in situ with synthetic enamel paint by spraying including filling cavities with filler, one coat after cleaning all dust etc complete all as specified and directed by Engr-in-Charge.

Repairing of ceiling fan of any make, 1200 mm sweep dismantling its parts cleaning properly, rewinding with super copper enamelled wire suitable gauge, varnishing, oiling and greasing replacing petty items such as split pins, assembling and testing after fixing of fan blades, refixing at site and connecting complete complete all as specified and directed by Engr-in-Charge.

Supply and fix in repair Ball bearing suitable for 1200mm sweep ceiling fan of SKF or NBC or equivalent complete all as specified and directed by Engr-in-Charge.

Repairing of Exhaust fans 300 mm sweep and make, dismantling parts properly cleaning/removing old existing grease oil and removing old paint from blades. Applying new oil grease, varnishing of Rewinding, cleaning dust, rust & assembling and refixing at site complete all as specified and directed by Engr-in-Charge.

Repairing of Exhaust fans 380 mm sweep and make, dismantling parts properly cleaning/removing old existing grease oil and removing old paint from blades. Applying new oil grease, varnishing of Rewinding, cleaning dust, rust & assembling and refixing at site complete all as specified and directed by Engr-in-Charge.

Repairing of Exhaust fans 450 mm sweep and make, dismantling parts properly cleaning/removing old existing grease oil and removing old paint from blades. Applying new oil grease, varnishing of Rewinding, cleaning dust, rust & assembling and refixing at site complete all as specified and directed by Engr-in-Charge.

Supply and fix in repair Ball bearing suitable for 300mm sweep ceiling fan of SKF or NBC or equivalent. complete all as specified and directed by Engr-in-Charge.

Supply and fix in repair Ball bearing suitable for 380mm sweep ceiling fan of SKF or NBC or equivalent complete all as specified and directed by Engr-in-Charge.

Supply and fix in repair Ball bearing suitable for 450mm sweep ceiling fan of SKF or NBC or equivalent complete all as specified and directed by Engr-in-Charge.

Supply , fixing, testing in repairs of JEF ECO SAFE Maintenance Free Grounding Solution set comprising of High tensile low carbon steel rod of 3 Mts length & 25 mm dia with 250 micron ( averaSchneider ) molecularly bonded copper on the outer surface to confirm with requirements of UL467 along with Back-fill compound strictly be a Carbon based conductive concrete type which has a resistivity of less than 0.12 Ohm Mtr as per Clause 14.5D of IEEE : 80 standard. Back-fill compound should be electronically conductive ( Like in metals ) and should not depend on moisture for conduction. JEF Powerfill Loresco compound shall be supplied in 50 Pound Bag. ( 1 Bag of 50 Pounds required per earthing set). Back-fill comound should be environment friendly, should solidify when mixed with water and set like concrete and should not leach / diffuse into the ground. A suitable earth terminaton clamp should also be supplied along with the set alongwith earth pit weatherproof incl complete all as specified and directed by Engr-in-Charge. Note - Back-fill compund shall not be mixed with any soil while pouring in the bore hole.

Supply and fixing in repair of MS/ GI hot dip/ powder coated perforated GI cable tray sheet thickness not less than 1.6mm ,50 mm height of tray and width not less than 450mm to be fixed on any wall (brick/stone) vertically/horizontally ,including tray cover of thickness not less than 2.00mm,including all accessories complete bending, shaping, drilling, welding, cutting and including all fixing arrangement such as suitable size of nuts, bolts, coupler plates etc complete all as specified and directed by Engr-in-charge.

Supply and fixing Earth continuity conductor or main earthing lead fixed to wall on batten or recess or chases or buried in ground or drawn in conduit/ pipe or fixed to poles or any other indicated situation for loop earthing etc. as required 4mm dia galanised iron or steel wire complete all as specified and directed by Engr-in-Charge.

Supply and fixing Earth continuity conductor or main earthing lead fixed to wall on batten or recess or chases or buried in ground or drawn in conduit/ pipe or fixed to poles or any other indicated situation for loop earthing etc. as required 25x4mm dia galvanised iron or steel strip all as directed

Supply and fix in repair/replacement of single phase DOL Starter 2 HP- 10 HP as per site requirement , 415V, 50 Hz complete all as specified and directed by Engr-in-Charge. Make :/Havells cat part no-IHPDOLLAE/Siemens/L&T Note : All lights to be taken out before commencement of civil work and to be submitted to MES store for refixing.

Shree Ayyappa Engineering

C S Sharma and Co

MUKESH CONSTRUCTION CO

Garima Construction Co