Replacement of pumps valves and electrical fitting

Amount

Excavation with mechanical/Manual means in all types of soil, including shoring and strutting, bailing out water/pumping off water if required, removing and stacking or Disposing simultaneously the excavated soil anywhere within the ACTREC Campus and/or spreading soils in layers for site development and backfilling the same after completion of chamber work. All complete as per specification and as directed by the Engineer-incharge. Only the planned area as per the drawing will be measured. Only plan area of Rubble soling shall be measured with depth.

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level in all shapes and sizes in Cement mortar 1:4 (1 cement : 4 coarse sand). For Inspection Chambers, Manholes etc.

Structural steel work in single section, fixed with or without connecting plate, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete.

Fixing available floor tiles by levelling the ground and fixing the tiles on 12 mm thick mortar 1:4 (1 cement : 4 coarse sand) which is included in the rate as per the instruction of engineer incharge

Demolishing brick work manually/ by mechanical means including stacking of serviceable material and disposal of unserviceable material outside ACTREC campus as per direction of Engineer-in-charge.

Providing and laying in position cement concrete of specified grade including the cost of centering and shuttering : Plain cement concrete 1:3:6

Demolishing CC/RCC works manually/ by mechanical means including disposal of material outside the campus all complete as per direction of Engineer - in - charge.

Providing and laying in position Cast In-situ design mix cement concrete for M25 grade reinforced cement concrete work; using coarse aggregate and fine aggregate derived from natural sources, Portland Pozzolana / Ordinary Portland /Portland Slag cement, admixtures in recommended proportions as per IS: 9103 to accelerate / retard setting of concrete, to improve durability and workability without impairing strength; including pumping of concrete to site of laying, curing, carriage for all leads; including the cost of centering, shuttering, finishing but excluding the cost reinforcement as per direction of the engineer-in-charge. For pump foundation, chambers etc. The item is including SITC for foundation bolt of 300mm on all sides for pumps.

Providing and Fixing of reinforcement steel including material fabricating, trasporting, loading, unloading, storing on raised steel rack platform, handling, straightening, cutting to length, bending, making hooked ends, hoisting into place at all levels and heights and binding in position (including Providing & using 18 gauge binding wire) reinforcement bars of all diameters (IS 1786 ,Fe 500 of all grade) to shape and size as per approved bar bending schedules and structural drgs. for all kinds of works at all heights & depths as specified including cost of approved quality PVC/Concrete cover blocks, spacers, chairs at regular interval as per relevant IS code and such other works that are required to make it complete. Quantity of steel as per drawing, approved BBS and with authorized overlaps only shall be measured and paid for. Quantity for chairs and spacer bars will not be paid. The measurement shall be as per IS 1200 and reinforcement hooks and bends shall comply with the requirement of IS 2502 unless clearly specified above.

P.V.C. PIPES:Providing, laying, jointing, fitting, testing heavy quality P.V.C. pipes of Prince, Supreme etc. make & of required dia including all fittings required as per site requirement & laying the same at any floor levels including scaffolding all jointing materials & clamping in wooden blocks if required etc. complete as directed & specified by Engineer-In-Charge. - 25mm

P.V.C. PIPES:Providing, laying, jointing, fitting, testing heavy quality P.V.C. pipes of Prince, Supreme etc. make & of required dia including all fittings required as per site requirement & laying the same at any floor levels including scaffolding all jointing materials & clamping in wooden blocks if required etc. complete as directed & specified by Engineer-In-Charge. - 32mm

P.V.C. PIPES:Providing, laying, jointing, fitting, testing heavy quality P.V.C. pipes of Prince, Supreme etc. make & of required dia including all fittings required as per site requirement & laying the same at any floor levels including scaffolding all jointing materials & clamping in wooden blocks if required etc. complete as directed & specified by Engineer-In-Charge. - 50mm

P.V.C. PIPES:Providing, laying, jointing, fitting, testing heavy quality P.V.C. pipes of Prince, Supreme etc. make & of required dia including all fittings required as per site requirement & laying the same at any floor levels including scaffolding all jointing materials & clamping in wooden blocks if required etc. complete as directed & specified by Engineer-In-Charge. - 75mm

P.V.C. PIPES:Providing, laying, jointing, fitting, testing heavy quality P.V.C. pipes of Prince, Supreme etc. make & of required dia including all fittings required as per site requirement & laying the same at any floor levels including scaffolding all jointing materials & clamping in wooden blocks if required etc. complete as directed & specified by Engineer-In-Charge. - 110mm

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. 20 mm nominal dia Pipes

Pump Set: Supply installation testing and commissioning of centrifugal pumps set factory assembled & tested for rated efficiency complete with TEFC motor EFF1 rating, common base frame, mechanical seals, vibration isolators including flexible connections. etc for recirculation of water . The pumps shall be suitable for operation on 415 +/- 10% volts, 50Hz 3ph AC supply. and all other accesories i.e .Base frame, coupling, coupling guard and foundation bolts, etc. require to install & commissioning of pump as per instruction & directed by engineering -in -charge. The pump parameters shall be as given,

Head. 85 m Capacity .m3 / h 85 Power rating . 60 hp Rpm 1475

Head. 75 m Capacity .m3 / h 130 Power rating . 60 hp Rpm 1475

Head .50m Capacity .m3 / h:- 50 Power rating . 20 hp Rpm .1450

Dismantling of Existing Pumps, pipe line , valves, foundation etc. from the all three pump house and to be keep as per instructions & as directed by O-I-C, ES.

Modification in piping work: Modification in existing piping work of inlet/outlet water line using class ‘C’ MS pipes, flanges, strainers, bends, reducer with all welding, cutting & joining and Tee connections for all gauges (pressure/ temperature /flow /drainage / descaling), complete with proper support of angle/channel etc, painting of entire installation with two coat of bituminous paint/enamal paint ( inside coating of food grade epoxy wherever possible) etc. as per requirement, all as per specifications, instructions & as per directions of O-I-C, ES.

300 mm class 'c' MS pipes

150 mm class 'c' MS pipes

125 mm class 'c' MS pipes

100 mm class 'c' MS pipes

40 mm class 'c' MS pipes

32 mm class 'c' MS pipes

25 mm class 'c' MS pipes

Butterfly valves :The valves used at the inlet and outlet of the pumps shall be PN16 rating. Supplying and Installing Cast iron double flange Butterfly Valve of following sizes.All the necessary hard ware etc.

Butterfly valve of 150 mm

Butterfly valve of 125 mm

Butterfly valve of 100 mm

SITC of Ductile iron Double flanged Resilient Seated Gate Valve with EPDM Coated wedge disc, with Epoxy coating inside & outside, PN-16 rating with fittings, nut, bolts , gaskets & washers, with LOTO arrangements. As per IS .

300 mm dia.

150 mm dia

100 mm dia

SITC of Non-return Valve with duel plate of C I body SS plates vulcanized NBR seal flanged end & PN 16 pressure rating for water circulation including necessary hardware etc.

125mm dia

100mm dia

Pressure gauges with SS siphon tube,and all other assesories and hardware as per instructed and as directed by OIC-ES

SITC of Brass foot vale for connecting existing HDPE / MS pipe line with all necessary fanges,hardware, supports etc as per instruction and as directted by OIC-ES.

150mm dia brass foot valve

125mm dia brass foot valve

SITC of CI double acting Air valve for connection in exsiting pipe line with all necessary fanges,hardware, supports etc as per instruction and as directted by OIC-ES.

Double acting Air valve 50 mm

Double acting Air valve 100 mm

SITC of Switch Valve for connection in exsiting pipe line with all necessary fanges,hardware, supports etc as per instruction and as directed by OIC-ES.

150mm dia

100mm dia

Electrical Panel for PH no 01 :- SITC of new electrical panel with switch gear items as mentioned in tender documents with following IC and OG details including fabrication and fixing of MS channel foundation for panels, space heater, panel lighting with required all control components and wiring etc. The rates includes dismentling , shifting of existing LT panel with all cables and accesories 01 Nos Incomer feeder 800A MCCB 4pole , 415volt , 50Hz with rotary operating handle , neutral link , termination bus bar with accessories cable chamber suitable for termination of 02 nos 3.5 * 300sqmm aluminium armoured incomer cable. Also including Main Phase voltage R ,Y , B LED indication lamp, Breaker ON OFF TRIP LED Indication lamp , AC Ammeter & Voltmeter , MFM meter , Metering CTs and protection CTs as required, specifications as per tender documents Out going feeder as below A) 60HP 3 phase pump starter feeders – 03 nos with required rating main TPN MCCB + neutral link as per standard , R Y B LED Indication lamp , On OFF TRIP LED indication lamp , OLR , protection relays, single phase relay , aux contacts , timers, star delta contactors , Start stop push button , control MCB , Multi function meter analogue ameter , voltmeter , pump running hour meter , including all controls and wiring required for functioning of starter. B ) 05HP 3 phase pump starter feeders – 02 nos with required rating main TPN MPCB + neutral link as per standard , R Y B LED Indication lamp , On OFF TRIP LED indication lamp , OLR , protection relays, single phase relay , aux contacts , , Start stop push button , control MCB , MFM , including all controls and wiring required for functioning of starter. C) 63A TPN LPDB feeder 01 nos for LPDB D) 63A TPN MCCB feeder spare 03 Nos E) 250A MCCB feeder spare 01 Nos with , front door rotary operating mechanism including , MFM , ON OFF TRIP LED Indication lamp

Electrical Panel for PH no 02 :- SITC of new electrical panel with switch gear items as mentioned in tender documents with following IC and OG details including fabrication and fixing of MS channel foundation for panels, space heater, panel lighting with required all control components and wiring etc. The rates includes dismentling , shifting of existing LT panel with all cables and accesories 01 Nos Incomer feeder 125A MCCB 4pole , 415volt , 50Hz with rotary operating handle , neutral link , termination bus bar with accessories. Also including Main Phase voltage R ,Y , B LED indication lamp, Breaker ON OFF TRIP LED Indication lamp , AC Ammeter & Voltmeter , MFM meter , Metering CTs and protection CTs as required, specifications as per tender documents Out going feeder as below A) 20HP 3 phase pump starter feeders – 02 nos with required rating main TPN MCCB + neutral link as per standard , R Y B LED Indication lamp , On OFF TRIP LED indication lamp , OLR , protection relays, single phase relay , aux contacts , timers, star delta contactors , Start stop push button , control MCB , MFM , pump running hour meter including all controls and wiring required for functioning of starter. B) 63A TPN LPDB feeder 01 nos for LPDB C) 63A TPN MCCB feeder spare 02 Nos D) 05HP 3 phase pump starter feeders – 01 nos with required rating main TPN MPCB + neutral link as per standard , R Y B LED Indication lamp , On OFF TRIP LED indication lamp , OLR , protection relays, single phase relay , aux contacts , Start stop push button , control MCB , MFM , including all controls and wiring required for functioning of starter.

Electrical Panel for PH no 03 :- SITC of new electrical panel with switch gear items as mentioned in tender documents with following IC and OG details including fabrication and fixing of MS channel foundation for panels, space heater, panel lighting with required all control components and wiring etc. The rates includes dismentling , shifting of existing LT panel with all cables and accesories 01 Nos Incomer feeder 400A MCCB 4pole , 415volt , 50Hz with rotary operating handle , neutral link , termination bus bar with accessories. Also including Main Phase voltage R ,Y , B LED indication lamp, Breaker ON OFF TRIP LED Indication lamp , AC Ammeter & Voltmeter , MFM meter , Metering CTs and protection CTs as required, specifications as per tender documents Out going feeder as below A) 60HP 3 phase pump starter feeders – 02 nos with required rating main TPN MCCB + neutral link as per standard , R Y B LED Indication lamp , On OFF TRIP LED indication lamp , OLR , protection relays, single phase relay , aux contacts , timers, star delta contactors , Start stop push button , control MCB , MFM , pump running hour meter , including all controls and wiring required for functioning of starter. B) 20HP 3 phase pump starter feeders – 01 nos with required rating main TPN MCCB + neutral link as per standard , R Y B LED Indication lamp , On OFF TRIP LED indication lamp , OLR , protection relays, single phase relay , aux contacts , timers, star delta contactors , Start stop push button , control MCB , MFM , pump running meter , including all controls and wiring required for functioning of motor. C) 2 HP , 01 PH pump starter feeder 01 Nos D) 63A TPN LPDB feeder 01 nos for LPDB E) 63A TPN MCCB feeder spare 03 Nos F) 05HP 3 phase pump starter feeders – 01 nos with required rating main TPN MPCB + neutral link as per standard , R Y B LED Indication lamp , On OFF TRIP LED indication lamp , OLR , protection relays, single phase relay , aux contacts , , Start stop push button , control MCB , MFM , including all controls and wiring required for functioning of starter.

Cables & Termination Accessories

Supply, laying, testing & commissioning of 1.1 KV AC grade of 3.5 core x 25 sq. mm Al conductor cable PVC insulated ISI mark armored, bright annealed Aluminium conductor cable in air including clamping , saddling , cable route tag , for termination of 20 HP Pump 03 Nos

Supply, laying, testing & commissioning of 1.1 KV AC grade of 3.5 core x 35 sq. mm Al conductor cable PVC insulated ISI mark armored, bright annealed Aluminium conductor cable in air including clamping , saddling , cable route tag , for termination of 60 HP Pump 05 Nos

Supply, laying, testing & commissioning of 1.1 KV AC grade of 4 core x 16 sq. mm Al conductor cable PVC insulated ISI mark armored, bright annealed Aluminium conductor cable in air including clamping , saddling , cable route tag , for termination of Lighting cum power distribution board

Supplying & erecting heavy duty flange type brass cable glands for up to 3.5 x 25 sq.mm size for end jointing of various sizes for PVC armoured cable with brass washers, rubber rings complete with cable ends & leads connected, with gland double earthing, work completed in all respect all as per instructions

Supplying & erecting heavy duty flange type brass cable glands for 3.5 x 35 sq.mm size for end jointing of various sizes for PVC armoured cable with brass washers, rubber rings complete with cable ends & leads connected, with gland double earthing, work completed in all respect all as per instructions

Supplying & erecting crimping type copper lugs confirming to IS suitable for cables up to 16 sq. mm evenly crimped with high pressure tools & connected to switch gear terminals with brass/ cadmium plated nut bolts in an approved manners. all as directed by O-I-C, ES

Supplying & erecting crimping type copper lugs confirming to IS suitable for cables 25 sqmm evenly crimped with high pressure tools & connected to switch gear terminals with brass/ cadmium plated nut bolts in an approved manners. all as directed by O-I-C, ES

Supplying & erecting crimping type copper lugs confirming to IS suitable for cables 35 sqmm evenly crimped with high pressure tools & connected to switch gear terminals with brass/ cadmium plated nut bolts in an approved manners. all as directed by O-I-C, ES

SITC of 8 SWG tinned copper bare wire (1 run) for earthing of motors , LPDBs

SITC of Copper strip of size 25 x 3 mm (1 run) for connection to earth pit , panels , motors

SITC of Tinned copper earth plate electrode 600 x 600 x 3.15 mm earth station, 2.5 mtr below ground level as per drawing complete with all required materials like Cole, charcoal, salt, brass nut bolts & washers, watering arrangements, GI pipe (B class), concrete chamber, heavy duty cast iron cover plate & excavation in all types of soil in ground refilling & removal excess earth within a radius of 500 mtr. Etc. (2 Nos, of neutral earthing of T/F, 2 Nos. for T/f body earthing & 2 Nos. for panel earthing)Note:1.The chamber cover & plate shall be of heavy-duty hinged type & it shall weigh approx. 65 to 75 Kgs. For 450 x 450 mm size & shall be got approved by dept. (6 mm chequred plate with 40 x 40 x 6 mm angle iron frame)2.Plastering shall be done both inside & out side.3.The measurement of resistance of earth station & resistance of complete scheme of earthing layout shall be measured, recorded & got approved by Engg-in-charge.

Supply, laying, testing & commissioning of 1.1 KV AC grade of 3.5 core x 300 sq. mm Al conductor cable PVC insulated ISI mark armored, bright annealed Aluminium conductor cable in ground at 900 mm back filling & re-instatement, consolidation & removal of excess earth with in a radius of 500 mtr including clamping , saddling , cable route tag , laying of cable tiles / bricks , sand filling through out under ground route. Cables 02 Nos runs each runs 210 Mtr cable

Supplying & erecting heavy duty flange type brass cable glands for 3.5 x 300 sq.mm size for end jointing of various sizes for PVC armoured cable with brass washers, rubber rings complete with cable ends & leads connected, with gland double earthing, work completed in all respect all as per instructions

Supplying & erecting crimping type copper lugs for 150 sq. mm confirming to IS suitable for various core sizes evenly crimped with high pressure tools & connected to switch gear terminals with brass/ cadmium plated nut bolts in an approved manners along with lug crimping pest etc

Supplying & erecting crimping type copper lugs for 300 sq. mm confirming to IS suitable for various core sizes evenly crimped with high pressure tools & connected to switch gear terminals with brass/ cadmium plated nut bolts in an approved manners along with lug crimping pest etc

Supply & istallation of RCC hume pipe 150 mm Dia along with collars including jointing of pipes with cement, consolidating & making good surface as per the existing

Switch Socket , lighting , fans , ehaust fan , LPDB accessories

Supply , fixing and termination of 15 A,5 pin, switch socket combination board on wall

Supply , fixing and termintion of of 5 A, switch modular in modular surface PVC board

Supply , fixing and termination of Ceiling fan dimmer, 400/600W modular type in modular PVC board

Supply and fixing of 4 way Surface modular boxes

Supply and fixing of 4 way Surface modular face plate

Supply and fixing of 6 way Surface modular boxes

Supply and fixing of 6 way Surface modular face plate

Supply , fixing and termination of 22W, 4' long LED Tube light fixture

Supply , fixing and termination of 70W, LED street light fitting, IP-65 outdoor type with mounting breket , JB and all mounting accessories etc

Supply , fixing and termination of 1 phase exhaust fan 300 mm Size with MS frame & gravity louvers, 1400 RPM, 230 Volt, 50 Hz.

Providing, fixing & commissioning of Crompton make or equivalent ceiling fan White/ Brown colour as per requirement including down rod, double ball baringSize 1200 mm sweep

SITC of FRLS PVC insulated copper conductor , single core wire 1.5sqmm size in surface/ recessed PVC conduit as required

SITC of FRLS PVC insulated copper conductor , single core wire 2.5sqmm size in surface/ recessed PVC conduit as required

Lighting cum power distribution board made out of 2 mm thick (in case of fabrication) MS CRCA sheet with concealed hinges, mounted on MS angle frame & grouted on the wall/fixed on the coloum with anchor fastener with earthing terminal, neutral link, interconnection with adequate size of Bus-bar/wires, interior of the DB shall be covered with 3 mm thick FRP sheet with necessary cut out, neoprene gasket, painting with seven tank metal treatment process(Shade to be got approved)/powder coating 08 ways including 63 amps TPN MCB--1 No. /// 40 amps DP ELCB(30 mA)--3 Nos /// 16 amps SP MCB (8ways)--24 Nos. all links etc.

Supply & Fixing of PVC rigid conduit 25 mm Size with spacers & saddles screws, rawal plug etc. along with all accessories complete in all respect on any hard surface/wall/trench/ceiling etc.

Supply & Fixing of 1.25 Inch casing capping with screws, rawal plug etc. along with all accessories on any hard surface/wall/trench/ceiling etc.

ECOSYSTEM RESOURCE MANAGEMENT PVT. LTD.