PROVN OF 02 X REVENUE AND 08 X MINOR WORKS IN THE AREA OF AGE B/R-I AND B/R-II UNDER GE (EAST) DELHI CANTT-10

Amount

Surface excavation not exc (not exceeding) 30 cm deep and averaging 15cm deep in hard and dense soil and getting out Complete all as speicified and directed.

Returning filling in including spreading leveling, watering and well ramming in layers not exc 25 cm in any type of soil, complete all as specified & directed.

Removing excavated material not exc 50m and depositing where directed at a level not exc 1.5 mtr above the starting point, complete all as specified & directed.

Excavating in post holes (or similar holes) each not exc 0.5 cum, getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm, PCC 1:3:6, complete all as specified & directed

M&L for 0.50MM thick prepainted galvalume aluminium zinc coating GI based semi corrugated/ profile steel sheeting of any colour having tensile strength of 550 MPA as in roof covering, wall cladding fixed with self tapping screws or 'L' Type and 'J' Type or crancked hook bolts in lieu of screws as per manufacturer's instructions incl reidgs as in roof covering, complete all as specified & directed.

S&F MS work as in rafters, purrlins, and other connected work incl special shaped washer etc complete using ERW or induction butt weldws tubes conforming to IS-1161 - 1979 (Gde St-240) all as specified and as directed.

M&L for preparation of new steel surfaces and applying two coat of synthetic enamel paint over a coat of red oxide primer on surface of any description, over 10CM in width or girth, not othrewise dicsribed.

M&L for 150mm thcik for hard core broken stone or builders of gauge not exc 63mm deposited, spread and leveled in layers not exc 15cm thick, watered and rammed to a true surface complete all as specified and directed by Engr -in Charge.

Providing and laying at or near ground level factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 incl making joints with or without grooves (thicknes of joints except at sharp curve shall not be more than 5mm), incl making drainage opening where required complete all as specified and directed by Engr-in-Charge.

M&L for 75mm thick cement concrete type D-2 (1:4:8) (using 40 mm graded stone aggregate) below interlocking paver blocks complete all as specified & directed by Engr-In-Charge.

Providing and laying 80mm thick factory made chamfered edge cement concrete paver block of M-30 grade with approved colour, design & pattern as foothpath, parks, lawns, drive ways or light traffic parking etc. of required strength, thickness & size/ shapes, made by table vibratory method using PU mould, laid in required colour & pattern over and incl 50mm thick compacted bed of coarse sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with fine sand and cutting of paver block as per required size and pattern, finishing and sweeping extra sand, complete all as specified and directed.

M&L for Cement concrete type D-2 (1:4:8) (using 40 mm graded stone aggregate) as foundations, flling and mass concrete complete all as specified & directed by Engr-In-Charge.

M&L for Cement concrete type B-2 (1:2:4) (using 40 mm graded stone aggregate) as foundations, flling and mass concrete, complete all as specified & directed by Engr-In-Charge

Excavation in trenches, not exc 1.5 m wide and not exc 1.5 m in depth, for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. not exc 10 sqm on plan and not exc 1.5 m in depth and getting out and getting out in any type of soil complete all as specified and directed.

M & L for RCC M-25 (design mix) as in foundation, including rafts , footings , foundation beams, plinth beams; bases for columns, etc ; basement slabs, under- reamed piles and mass concrete, complete all as specified and directed by Engr-in-Charge.

M & L for RCC M-25 (design mix) as in columns, pillars, piers, posts and struts etc, complete all as specified and directed by Engr-in-Charge.

M & L for RCC M-25 (design mix) as in Beams , cantilevers, bressummers, lintels over 1.5 m span etc, complete all as specified and directed by Engr-in-Charge.

Cutting opening in cement concrete walls (any description) for door, window and other openings (with or without reveals) or enlarging existing openings, including trimming and making good surface to receive rendering, etc.

Surface dressing not exceeding 15 cm deep and getting out in any type of soil complete all as directed.

M&L false ceiling with 4mm thick 'E' Board (Make:Everest Ltd or Charminar ) fixed over GI powder coated inverted Tee or'L' section suspended from ceiling with 3mm thick GI wire tie with ceiling/trusses with suitable arrangement complete all as directed and specified (a) Main runner/ Cross tee size 29x24.7x0.8mm (b) Wall angle of size 22.2x22.2x0.65mm (C) Size of grid 600x600mm (d) Two coats oil bound distemper one side of board (e) Powder coating on exposed side of tee/angle including dismantling of old ceiling any size and description complete all as specified and as directed

M&L for MS work Fe-290 (Gde E- 165) Joist, channel, angle, or tee sections, fixed independently, without connecting plates, etc. (cut to ordinary lengths i.e. within 20mm of the length indicated) complete all as specified and directed.

M&L for cement concrete 1:2:4 type B-1 (using 20mm graded stone aggregate) as in copings, benching for manholes and the like including weathering slightly rounded or chamfered angles and throating, all as specified and directed.

M & L for Mild steel TMT bars 10 mm dia., and over cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with mild steel wire (annealed) not less than 0.9 mm dia., or securing with clips etc complete all as specified and directed by Engr-in-Charge.

M&L for mild steel TMT bars 6 mm to 8 mm dia and over, cut to length, bent to shape required including cranking bending spirally & binding with and including mild steel wire (annealed) not less than 0.9mm dia etc complete all as specified and directed by Engr-in-Charge.

M&L for mild steel TMT bars 5 mm dia and over upto and including 10 mm dia in strirrups, spaces and binder and including mild steel wire (annealed) not less than 0.9mm dia etc complete all as specified and directed by Engr-in-Charge.

M & L for form work to sides of concrete foundation, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams: and similar works; vertical or to batter for flat rough finished surfaces complete all as specified and directed by Engr-in-Charge.

M & L for form work to sides of pillars, posts, struts, piers, columns and stanchions size of square, rectangular or polygonal for flat rough finished surfaces complete all as specified and directed.

M & L for form work to edges of concrete flats, treads breaks in floors , window cills , concrete railling, opening in concrete walls, floors and roofs RCC/PCC bands floors roofs n exc 20 cm wide and sides of RCC/PCC bands in walls , horizontal or slooping and similar work exc 10 cm and not exc 20 cm wide surface finished rough complete all as specified and directed.

M&L for brick work with sub class 'B' bricks, straight or curved on plan exc 6 m mean radius built in CM 1:6 all as specified and as directed.

M & L for Brick work with sub class ‘B’ bricks, straight or curved on plan exceeding 6 m mean radius built in cement mortar 1:4, in half brick thick complete all as specified and directed by Engr-in-Charge.

M & L for rendering 15mm thick on fair faces of brick work or concrete surfaces (CM 1:4) finished even and smooth without using extra cement, incl mixing of water proofing compound complete all as specified and directed.

M&L for rendering 15 mm thick in CM 1:6 finished even and smooth without using extra cement, complete all as specified and directed.

M&L Earth Soil spreading , levelling in layers not exc 25 cm thick each layer with well ramming including watering as required under the floor complete all as specified and directed by Engr -in Charge. (Note :- Earth Soil available surplus soil from the excavation at ground )

M&L for 75 mm thick cement concrete type C-2, 1:3:6 (using 40mm graded stone aggregate) as in sub base complete all as specified and directed.

M & L for 25 mm thick PCC type B-0, 1:2:4 (using 12.5mm graded stone aggregate) as in flooring, under tiles and etc all as specified and directed

M & L for non skid ceramic tiles 7 to 8mm thick (Square/rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15mm thick screed bed in CM 1:6, complete all as specified.

M & L for Glazed Coloured Ceramic tiles 300x450x7mm or 450x350x7mm thick on vertical surface such as skirting, dados etc, set and joint in neat cement slury and pointed in white or colour cement to match, over and incl 10mm thick rendering/ backing coat in CM 1:4, complete all as specified and as directed.

S&F Anodised aluminium window and ventilator shutters, fixed type without sash bar, aluminium section weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws etc. complete all as specified and as directed.

S&F 3 mm thick Sheet glass, ordinary quality and glazing with oil putty in square not exc 0.5 sqm in each pane complete and all as specified and directed.

S&F solid PVC door frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with MS square tube, complete all as specified and directed.

S & F Factory made solid panel PVC door/cup board shutter 30 mm thick (style) consisting of frame made out of M.S tubes for top & bottom rails. M.S frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement or stiles and plain colour PVC sheets for top rail, lock rail and bottom rail on either side and as gap insert for top rail and bottom rail. Panelling of plain colour PVC sheet to be fitted in the M.S frame welded/sealed to the stiles and rails with suitable PVC sheet beading and joined together with solvent cement, suippling and fixing in the frame at site as per specification in SSR Part-I. complete all as specified and directed by Engr-in-Charge..

S&F butt hinges 100mm size, medium weight, cold rolled mild steel, complete all as specified and directed.

S & F 150 mm long aluminium, handles, caste type, anodized, complete all as specified and as directed.

S & F 150 mm long aluminium, anodized, barrel twoer bolts of extruded section, complete all as specified and as directed.

Material and labour for preparation of new brick/concrete plastered or unplastered surfaces of walls, pillars, cornices by brooming down etc and applying two coat of cement base paint over a coat of cement primer etc complete all as specified and directed by Engr -in Charge.

M&L for 3 coats of white wash on wall including preparation of newly plastered wall surfaces, complete all as specified and directed.

M & L 75mm thick PCC 1:3:6 type C-2, (using 40mm graded stone aggregate) as in sub base, Floors, Paving, plinth protection, finished even and fair without using extra cement complete all as specified.

S & F Vitreous China wash down pedestal pattern EWC, white and including with PVC (SWR) ' S' Trap/P-trap , including seat cover with connection to drain and to flushing pipe antisyphonage pipe, and making good to floor complete all as specified and directed.

S&F 10 Ltrs capacity PVC valveless symphonic action type flushing cistern white low level with inlet, ball valve float handle including bracket & flushing pipe etc complete all as specified and directed.

S&F full padestal pattern wash hand basin, size of basin 630mm x 510mm and padestal of 900mm long ivory colour as approved by GE including fixing waste pipe and chromium plated brass waste fitting complete including provision of pair of mild steel angle iron brackets of suitable size duly painted, complete all as specified and as directed.

S&F Chromium plated tubular towel rail, 20mm dia D type, 60 Cm long between flanges along with a pair of brackets and attached to wall as directed.

S& F Liquid soap container of PTMT fixed with and including Chromium plated brass screws and wooden/plastic cleats. (Minimum weight 105gms) to wall as specified and directed

S&F 15 mm fancy type concealed Stop valves, with long shank cup chromium plated cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed complete all as specified and directed by Engr in Charge.

S&F 15mm bore medium grade, galvanised tubes with all fittings and fixed complete to wall and ceilings or laid in floor complete all as specified.

S&F 20mm bore `Medium grade` galvanised tubes with all fitting,and fixed complete to wall and ceilings or laid in floor complete all as specified.

M & L for 1000 litre rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) hoisted and fixed in position including 20mm dia PTMT ball valves, high pressure, with polythese float and flynut complete, screwed for iron pipe or brass ferrule and fixed all as specified in SSR Part-I complete all as specified.

S & F 20 mm bore Gun metal, globe or gate valves, with iron wheel head / leaver arm, screwed both ends for iron pipe and fixed

S & F 15 mm bore Gun metal, globe or gate valves, with iron wheel head / leaver arm, screwed both ends for iron pipe and fixed.

S & F PVC connections 15mm size with PTMT nuts of length 450mm complete all as specified and as directed.

S & F 75mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid on walls or in floors complete all as specified.

S&F 75mm size PVC cowls complete all as specified.

M & L for 75mm bore PVC (SWR) floor trap, plain with stainless steel floor water with cockroach trap 100 mm to 125 mm dia with hole for waste pipe including jointing with solvent cement, to waste pipe fixed in cement concrete 1:2:4 type B1 complete all as specified and as directed.

S & F 110mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors, complete all as specified and directed.

S & F 110mm bore PVC (SWR) bends with access door complete all as specified.

S&F of 110mm bore of PVC (SWR) junction single,(Single T) equal or unequal provided with access door, complete all as specified and directed.

S & F precast SFRC square or rectangular manhole cover 75 mm thick with frame medium duty conforming to IS-12592 incl necessary reinforcement, complete all as specified and directed.

M & L for form work to sides and soffits of suspended slabs such as roof slabs , landings and similar work not exc 200 mm thick (horizontal or sloopping) for flat rough finished surfaces complete all as specified and directed by Engr -in Charge.

M & L for form work to sides and soffits of floor or roof beam, beam hauchings, girders, bressum-mers, lintels, cantilevers, shelves including supports, overhangs, etc also splays between floors and beams etc for flat rough finished surfaces complete all as specified and directed by Engr -in Charge.

M & L Rendering 10 mm thick on fair faces of concrete or concrete surface in ceiling in CM 1:3, finished even and fair complete all as specified and directed by Engr -in Charge.

M&L for 3 coats of white wash on ceiling including preparation of newly plastered surfaces, complete all as specified and directed.

S&F 15mm bore angle/stop valve with flange complete all as specified & directed Make Somany Cat No 1060/Cera Cat No 220908/Hindware Cat No-F850073-MARC MOR-1060A

PCC (1:2:4) type B-0 using 12.50 mm graded stone aggregate as in brenching for manholes, bands, coping, bed plate etc with slightly chamfered or rounded angles including necessary from work, if any, and finishing exposed surface even and smooth without using extra cement complete all as specified & directed.

M&L for pre-cast reinforced cement concrete (1:2:4) type B-1 using 20mm graded stone aggregate as in manholes cover, drain cover and set in cement mortar (1:4) including form work complete all as specified & directed.

MS Framed work such as grills, gratings, etc. with ends of bars shouldered and/ or riveted, or forged into spikes, framed guard bars, barred iron doors, ladders, framed balusters, walk ways, railings, framework of water tanks and similar work conforming to Fe.290. Gde-E-165 complete all as specified and directed.

S&F DWCPE (SN8) nominal size 150 mm (internal dia) mm including all fixing accessories or fittings like socket/spigot joint with elastomeric sealing ring, rubber ring, SILAID rubber lubricants required for laying of pipes, laid in trenches, complete all as specified and as directed.

M&L for PCC 1:3:6 type C-2 (using 40mm graded crushed stone aggregates) bedding for sewage lines of 150 mm dia incl packing under and haunching against the sides of pipe after they are laid and tested complete all as specified and directed.

Cutting into existing manholes for connecting new drains internal dia of pipe 150mm, making good to pipe and rendering, cutting out existing benching for and forming branch channel (1/2 round or 3/4 section) in cement concrete 1:2:4 type B-l smooth finished, and reforming benching as required

M&L for PCC (1:3:6) type C-2 (using 40mm graded stone aggregate) as in foundation, surface channels and drain etc, complete all as specified and directed.

Taking down chowkats or frames with shutters (without taking off shutters from frames) area not exceeding 1.50 sqm each complete all as specified

Taking down chowkhats or frame with shutters exc 1.5 Sqm and not exc 4.00 sqm ditto but with shutters (without taking off shutters from the frame)each complete all specified and directed.

Supply and fixing factory made UPVC white colour Sliding window Three track with provision of window ac made of extruded profiles with wall thickness of 2.3mm (+ -0.2mm). Window profile with hollow section with multi chamber. Frame (88mm x 52mm), sliding sash (42mm x 67mm). Sliding mesh Sash (42mm x 57mm) Sliding interlock (One vertical length in each shutters) (45.5mm x 28mm), Glazing bead (24.5mm x 16mm) will be miterd cut and fusion welded at all corners, including drilling of holes for fixing hardware and drainage of water etc., making arrangement for fixing of hardware. EPDM gasket, 1.2+ -0.2mm thick galvanised steel Frame (30mm x 18mm) 2 nos, sliding sash (30mm x 18mm), sliding mesh sash (26mm x 10mm) profile to be inserted in required profile, frame will be fixed to the wall with 8mm x 100mm long fasteners, Hardware [Touch Lock of zinc alloyed (white powder coated), steel roller system including wire mesh and 5mm glass Stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and required accessories.

Factory made single extruded WPC solid door/window ceosetry winodws and other frames single/double chowkhat chowkhat of size 65mm x 125mm cpmprisingn of virgin PVC polymer of K value 58-60 suspension grade calcium carbonate and natural fibre wood powder/ rice husk/ wheat husk and non toxic additives (maximun toxicity index of 12 for 100gms fabricated with miter joints aftr applying PVC colvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/cum screw withdrawl steenght of 2200 N FACE and 1100 N Edge minimum compressive strength of 58 N/mm2 modules of elasticity 900 n/mm2 and resisitance to spread of flames of class A category with property of being termite/borer proof water/ moisture proof and fire retardant.

Factory made single extruded WPC solid decorative type flush door odf size 35mm thick comprising of virgin PVC polymer of K value 58-60 suspension grade calcium carbonate and natural fibre wood powder/ rice husk/ wheat husk and non toxic additives (maximun toxicity index of 12 for 100gms fabricated with miter joints aftr applying PVC colvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 650 kg/cum screw withdrawl steenght of 1800 N FACE and 900N Edge minimum compressive strength of 50 N/mm2 modules of elasticity 850 n/mm2 and resisitance to spread of flames of class A category with property of being termite/borer proof water/ moisture proof and fire retardant. WPC to be laminated with PVC foil of minimum 14 microns thick of approved design pasted with hot melt adhesive on both ffaces of shutter and fixing with satinless teel butt hinges of required size with necesssary full threaded star headed counter sunk ss screws all as per direction of engineer . The cost includes the rate of butt hinges

Providing 35mm thick "RAJSHRI" BRAND FACTORY MADE WIRE MESH SOLID WPC DOOR SHUTTER consisting of Density 500 Kg /Cbm Manufactured by an ISO-9001-2015 certified Company , Door to be panelled with SS mosquito Mesh and XTN aluminium Mesh for additional strength and safety purpose. (conforming as per IS:4020). The door should be water proof, termite proof, fire retardant and having screw holding capacity. Door to be fixed to frame with 3 nos. M.S powder coated butt hinges size 100mm*25mm*2mm and 32mm long steel screws drilled suitable to pass through both the walls of the M.S tube.Other hardwares should be fixed with 19*6mm size steel screws etc. Complete as per direction of Engineer-in -charge, manufacturer's specification & drawings. The cost inlcudes the rate of Butt Hinges complete all as specified and directed

S&F steel butt hinges Stainless steel medium weight cold rolled of size 100 mm and fixed to shutters. complete all as specified and as directed.

S & F 150 mm size stainless steel, handles complete all as specified and directed

S & F 150 mm size stainless steel barrel tower bolts and fixed complete all as specified and directed.

S & F 250 mm size ALDROPS (sliding door bolts) stainless steel 1.6x25cm (16x250mm) complete all as specified and as directed. (Make : - Godrej product Code SS ALDROPS -2282 and make as per approved make list and as approved by GE).

Vitrified coloured ceramic tiles light shade 10mm thick (square/rectangular) polished, area of tiles not exceeding 0.36Sqm each in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15 mm thick screed bed in cement mortar 1:4 including dismantling of old tiles with backing, complete all as specified and as directed.

Vitrified coloured ceramic tiles (light shade) 10mm thick (square/rectangular) polished, area of tiles not exceeding 0.36Sqm each as in vertical surfaces such as skirtings, dados etc., set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15 mm thick screed bed in cement mortar 1:4 including dismantling of old tiles with backing, complete all as specified and as directed.

M & L for extra for forming fair finished drain or channel 45 cm inner grith in cement concrete , using extra cement, including forms, moulds, mi-tred/ stopped ends etc.

S&F Plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes, without any attachment

M&L for Pre Polished Chequered Outdoor tiles 300x300 x 25mm thick, set, jointed and pointed in neat cement slurry in floors with grey cement and no pigment over screed bed or bedding layer of 15mm thick in CM 1:6 complete all as specified and directed.

Demolition of concrete (unreinforced) in of any description and in any position not otherwise specifically provided for complete all as specified and directed.

Cutting opening in cement concrete walls (any descript-ion) for door, window and other openings (with or without reveals) or enlarging existing openings, including trimming and making good surface to receive rendering, etc.

M & L for 500 Litres rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) hoisted and fixed in position including 20mm dia PTMT ball valves, high pressure, with polythese float and flynut complete, screwed for iron pipe or brass ferrule and fixed all as specified in SSR Part-I complete all as specified.

S & F 20mm bore stop valve, cast copper alloy screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions, complete all as specified and as directed.

S&F CP bottle traps for wash basins with inlet and outlet screwed for pipe or connections including necessary packing, union and cap and fixed complete all as specified.

S&F Vitreous China floor mounted WC (Cascade) one piece type (off white) including connection in drain etc incl water closet seat cover, flushing cistern, with P or S trap with all fitting and fixture complete all as specified and directed. (Make : Jaquar cat part No. SLS WHT 6851S300PP or equivalent in hindware/parryware as approved by GE).

S & F PVC connections 15mm size with PTMT nuts of length 600mm complete all as specified and as directed.

S&F 15 mm dia Bib tap fancy type cast copper alloy chromium plated with crutch or butterfly handle, screwed down , screwed for iron pipe or for brass ferrupe and fixed complete all as specified

M&L Anodised aluminium frame for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc. complete all as specified complete all as specified and directed by Engr-in-Charge.

S&F Anodised aluminium door shutters, aluminium section weighing 0.55 kg/m including necessary joining cleats, glazing clips, ruber neoprene packing, handles 2 Nos in each door, hinges, anodised aluminum snap beading screws with Pre-laminated exterior grade both side laminated board etc. complete all as specified.

S&F Prelaminated board 12mm thick, exterior grade, both side laminated board, fixed with screws to frame complete and all as specified and directed.

S&F Door closer hydraulically regulated, aluminium (die cast) body ,designation No. 3, universal type, suitable for door shutters of 851 to 1000 mm in width and of weight between 61 to 80 kg complete and all as specified and directed by Engr-in-Charge.

S&F stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with staless wire staples complete all as per specified and as directed

S&F 15mm bore 2 way angle valve with wall flange cast copper alloy, fancy type, chromium plated, screwed for iron pipe or brass ferrule complete all as specified & directed Make :- Jaquare cat part No. FLR-CHR-5041N or equivalent in hindware/parryware (as approved by GE).

S&F CP toilet paper holder with flap guard complete all as specified & directed Make :- Cera Cat No F5003110/ Somany Cat no 230507/Hindware-F880003

S&F CP brass soap dish complete all as specified & directed Make Hindware Cat No F880011/ Cera F5003106

S&F CP towel ring complete all as specified & directed Make Cera Cat No 5004105/Hindware Cat 880007 ,Somany Cat No 230703

S&F single lever WHB mixer of cast copper alloy, fancy type, chromium plated, and mixing hot & cold water screwed down for iron pipe and fixed complete all as specified and directed. ( Make : Hindware cat part No. ARI-CHR-39001B or equivalent in Jaquar/Hindware/parryware as approved by GE).

S&F CP 1 meter long health faucet ABS body with connection fixed to wall with CP screws & connection to tap complete all as specified (Make : Cera Cat Pt No-F8030104 ) or equivalent somany, hindware, parryware etc.

M&L for preparation of new plaster surface decorated brick/concrete plastered or unplastered surfaces of walls, pillars, cornices by brooming down etc and applying two coat of cement base paint etc complete all as specified.

M&L for 50mm thick sand filling under floors or in foundations including watering and consolidation slab including rubbing & polishing complete all as specified and directed by Engr-in-charge

M&L for Machine pressed precast concrete interlocking paver block any shape and size with grey cement & pigment conforming to IS 15658-2006 of 60mm thickness, M35 Grade & polishing complete all as specified and directed

Supply only liquid water proofing compound complete all as specified and directed.

Taking sown/ out carefully copper/ aluminium point wiring for light/fan/bell sockets 5/15 Amps complete without accessories as switches, Sockets, holders, ceiling roses, light fitting regulators etc ( to be measured seprately) and making good the distrubed surface all as specified.

M&L for point wiring complete with 1.5 Sq mm (nominal area) FRLS, PVC insulated un-sheathed and stranded copper conductor cable ISI marked drawing in PVC concealed conduit and PVC conduit fitting including drawing FRLS, PVC insulated unsheathed 1.5 Sqmm copper earth wire, connecting to common earth dolly with and incl Metal flush box of suitable size with modular sheet for fixing modular switches/sockets/fan regulator etc complete all as directed

One light point / fan point/ wall fan point/ bell/ buzzer controlled by one 1-way switch/ bell push.

One socket outlet point 5 amps on the same board.

One socket outlet point 5 amps on the independent board.

Description all as per Srl Item No 121 here-in-before but with 4 sqmm FRLS copper wire with 4 Sqmm FRLS copper earth wire for independent point.

S&F Modular switch 6 Amp, 1 way, 1 module size complete all as directed.

S&F Modular socket 6 Amp, 2/3 pin, universal type, 2 module size complete all as directed.

S&F Modular switch 16 Amp, 1 way, 1 module size complete all as directed.

S&F Modular socket 16 Amp multipurpose shuttered type, 2 module size with indicator lamp complete all as directed.

S&F Ceiling rose, insulated body, 3 terminal, 240 volts, 5 Amps and making good surface as original by plastering and whitewash/ colour/ distemper etc complete all as directed.

S&F LED luminaire 600 mm x 600 mm, 36 watt, 220 V AC recessed type with high efficiency PMMA diffuser soft glare free light complete with driver, holders suitable for roof ceiling including connecting up with driver three core flexible copper conductor cases of suitable size complete.

S & F surface and wall mounted LED tube light fitting with aluminium housing & interated electronic driver with tube rod of 20 Watt. slim elegant design.and including connected with 3 core 23/0.0076 insulated copper wire from celing rose to fittting connector all as specified and directed.

M&L Sub main wiring with 2 run of 4.0 Sqmm (nominal area) FR, PVC insulated, unsheathed and stranded copper conductor cable ISI marked, drawn in to separate PVC concealed conduit 25 mm dia with and including 4.0 Sqmm (nominal area) FR, PVC insulated, unsheathed and stranded copper conductor cable ISI marked as earth wire, connected with thimble from main DB to sub main DB complete all as directed.

M&L Sub main wiring with 2 run of 10.0 Sqmm (nominal area) FR, PVC insulated, unsheathed and stranded copper conductor cable ISI marked, drawn in to separate PVC concealed conduit 25 mm dia with and including 10.0 Sqmm (nominal area) FR, PVC insulated, unsheathed and stranded copper conductor cable ISI marked as earth wire, connected with thimble from main DB to sub main DB complete all as directed.

S&F in replacement of MCCB incommer distrubtion Board (Vertical Load line DB) double Door made out of CRCA mild steel sheet surface with insulated material like polyster or with epoxy powder coating and IP 43 & IK 09 protection, VTPN 04 way, 240 Volts with bus bar rating 200 Amps, dust and vermin proof suitable for incorporation of MCCB as incommer and MCB as outgoing and making all. Note: MCCB & MCBs will be measured and paid separately.

S&F in replacement MCCB 3 Pole, 160 Amp with breaking capacity 16 KA suitable for 415 Volts AC supply, with over load and short circuit protection complete all as specified and directed.

S&F of MCB DB conforming to IP 43-IK 09 with double door, SPN 12 way complete with din rail Netural and earthing bar after taking out the oldunserviceable DBs connection and making good the distrubed surfaces complete all as specified and directed.

S&F of MCB SP, B Curve type, 10 KA, 10 to 32 Amp, with over load and short circuit protection complete all as directed.

S&F of MCB SPN B Curve type, 10 KA, 63 Amp, with over load and short circuit protection complete all as directed.

Supply and fix in replacement of Modular AC 25 Amp SP mini MCB, 230 Volts, 50 Hz suitable for module sheet complete all as specified and as directed.

Supply and fix in Automatic Hand drier hot air dispenser with infrared sensor metal body with all accessories incl all electrical connection complete all as specified and directed. Make : Euroforce or equivalent.

Taking down water heater (Geyser) 25 litre capacity, and depositing to MES store yard, complete all as specified and directed.

S&F electric water heater of capacity 25 litre, vertical storage type, steel inner tank with glass linen 5 Star rating, withstand 8 bar pressure complete with all accessories such as heating element, pressure relief check safety valve, thermostat, connection piece, 3 core wire with plug etc complete all as specified and directed. (Make : Bajaj/ Havells/ Crompton).

S&F Steel fastner of 4" long and 8mm dia with Nuts & washer complete all as specified and directed.

Supply and fixing of steel wired connection 600mm long and C P brass adopter 15 mm dia with washer for hot and cold water from geyser and to withstand 8 bar pressure of water complete all as specified and directed.

S & F in replacement of Energy efficicent LED fittings 45W LED 6K suitable for building security light pressure die cast aluminium roadway luminaire with high power LEDs and HF electronic driver complete all as directed.

S&F of street light fitting bracket, 1mtr ling made out of galvanized iron pipe of 25mm dia size light grade complete with nit, bolts, complete all as specified and directed.

Material and labour for earthing complete with GI earth plate electrode 600mm x 600mm x 6mm thick buried directly in ground not less than 2.25 mtrs below ground level with top edge of plate not less than 1.5 mtr deep below normal ground level connected to galvinised earth wire 4 mm by means of nuts, bolts and check nut to earth plate and to main board or DB including necessary PCC 1:2:4 type B-1 pit, cover frame , GI pipe 15 mm dia light grade for protection and GI pipe 20 mm dia medium grade for watering with funnel, wire mesh, salt and charcoal dust all over the plate all as specified and as directed.

Supply and fix exhaust fan made of sturdy Engineering plastic complete with louvers shutter, voltage 230V, 50 Hz, RPM 1200, Copper winding of sweep 300 mm and depositing the old U/s item to MES store yard.

S & F of MCB DB conforming to IP 43 - IK 09 with double door , SPN 8 way complete with din rail Neutral and earthing bar after taking out the oldunserviceable DBs connection and making good the disturbed surfaces complete all as specified and as directed.

M&L for sand cushioning to under ground cable provided with layers of snad(8 cms deep before laying the cable and 15 cms deep after laying) complete allas specified and directed at site by Engineer-in-Charge.

Supply and laying burnt bricks class - B for protection of cable complete all asspecified and directed at site.

XLPE insulated armoured heavy duty U/G aluminium conductor cable served with an inner sheathing of PVC tape armoured with galvanised steel strip wire or tape and overall PVC sheathed of size 10 Sqmm 2 core, complete all as specified and as directed.

S&F instant heating Geyser 03 litre capacity vertical type with steel tank and glass inner linen including fastners (02 Nos) for hanging and CP and PVC connection for inlet & outlet upto stop cock complete all as specifed and as directed. (Make : Bajaj/ Havells/ Crompton).

S&F of LED bulk head fitting 10W with inbuilt driver complete all as specified and directed.

sony engineering works (BID ID -3489407)

M/S GEETANJALI ENTERPRISES (BID ID -3489787)

M/s Shubh Enterprises (BID ID -3494917)