GESU 74 2021 22 SPECIAL REPAIR TO RETAINING WALL NEAR BLDG NO P04 PROVN OF TOILETS BATHROOMS IN SINGLE JCOS ACCN FOR FOD PROVN OF ONE TOILET BLOCK INSIDE OFFRS MESS OF 103 INF TA SIKH LI GARHI AND

Amount

Surface excavation n.exc (not exceeding) 30 cm deep and averaging 15cm deep and getting out in hard /dense soil complete all as specified and directed.

Excavating in trenches, n exc 1.5 m wide and n.exc 1.5 m in depth; for foundation, & n exc 10 Sqm on plan and n exc 1.5 m in depth and getting out in hard /dense soil complete all as specified and directed.

Hardcore of gauge n exc. 63mm, deposited, spread and levelled in layers n exc. 15 cm thick, watered and rammed to a true surface complete all as specified and directed.

PCC 1:4:8 type D2 (using 40mm graded crushed stone aggregate) in foundations, filling and mass concrete complete all as specified and directed.

Brick work with sub-class 'B' bricks, straight or curved on plan exceeding 6 m mean radius built in cement mortar 1:6 complete all as specified and directed.

Brick work with sub class 'B' bricks, straight or curved on plan to any radius in half brick thick walls built in cement mortar 1:4 complete all as specified and directed.

Returning, filling incl spreading leveling watering and well ramming in layers not exceeding 25mm in any type of soil complete all as specified and directed.

Removing excavated material (soils) exceeding 250 m but n.exc. 500m and depositing where directed at a level not exceeding 1.5m above the starting point complete all as specified and directed.

Reinforced cement concrete M-25 (20mm graded aggregates) design mix as in foundations, including rafts, footings, foundation, beams; plinth beams; bases for columns, etc.; basement slabs, under-reamed piles and mass concrete complete all as specified and directed.

Reinforced cement concrete M-25 (20mm graded aggregates) design mix columns, pillars, piers,posts and struts complete all as specified and directed.

Reinforced cement concrete M-25 (20mm graded aggregates) design mix as in beams, cantilevers,bressummers, lintels over 1.5m span complete all as specified and directed.

Reinforced cement concrete M-25 (20mm graded aggregates) design mix as in slabs supported on walls, beams and columns in floors,roofs, landings, balconies,canopies, deck slabs and in shelves and the like complete all as specified and directed.

Reinforced cement concrete M-25 (20mm graded aggregates) design mix as in chajjas complete all as specified and directed.

Formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams,sides and soffits (if any) of foundation and plinth beams;and similar work; vertical or to batter for rough flat finished surfaces of concrete complete all as specified and directed.

Formwork to sides of pillars,posts, struts, piers, columns and stanchions for rough flat finished surface of concrete complete all as specified and directed.

Formwork to flat sides and soffits of or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floors and beams complete all as specified and directed.

Formwork to soffits of suspended flat slabs such as roof slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping) complete all as specified and directed.

Formwork to edges of concrete flats, treads breaks in floors, window cills, concrete railings,openings in concrete walls, floor and roofs n exc 20cm wide and sides of RCC/PCC bands in wall, horizontal or sloping and similar work exc 10cm but n exc 20cm wide complete all as specified and directed.

Formwork to chullah hoods, chajjas,troughs and similar items including edges for rough flat finished surface of concrete complete all as specified and directed.

TMT bars 10mm dia and over in reinforcement, cut to length, bent to shape required including cranking, bending spirally or hooping for columns, hooking ends and binding with Mild Steel wire (annealed) not less than 0.9mm dia complete all as specified and directed.

All as per srl item No. 20 above but 5mm dia and over including 10mm dia in stirrups, spaces and binders etc complete all as specified and directed.

Rendering 10 mm thick on fair faces of brick /concrete surfaces in cement mortar 1:6 and finished even and smooth without using extra cement complete all as specified and directed.

15 mm thick rendering in two layers (10mm + 5mm) on other than fair faces of brick/concrete or stone surfaces in cement mortar 1:4 and finished even and smooth without using extra cement complete with water proofing compound complete all as specified and directed. (WPC shall be measured separtely).

Supply only Liquid water proofing compound complete all as specified and directed.

Rendering 05 mm thick CM 1:4 on fair surfaces of ceiling work and finished even and smooth without using extra cement complete all as specified and directed.

Rendering 10 mm thick as backing coat to receive the tiles on fair faces of brick /concrete surfaces in cement mortar 1:3 and finished even and rough complete all as specified and directed.

Preparation of new plastered surfaces on walls and applying three coats of white wash.complete all as specified and directed.

Preparation of new plastered surfaces on ceiling and applying three coats of white wash complete all as specified and directed.

Preparation of new plastered surfaces on walls and applying two coats of cement based paint over a coat of alkali resistance proming paint complete all as specified and directed.

Preparation of new plastered surface and applying two coats of apex ultima paint over a coat of primer incl preparation of surfaces complete all as specified and directed.(colour of apex ultima approved by GE).

Shingle filling in floors or pavings, laid in layers n exc. 15 cm thick, spread, levelled, and blinded with earth and rammed including watering complete all as specified and directed.

75 mm thick cement concrete (1:4:8) type D2 as sub base to floor complete all as specified and directed.

25mm thick cement concrete 1:2:4 type B-0 using 12.5mm graded crushed stone aggregates as in floor and finished even and fair complete all as specified and directed.

10mm thick screed bed or bedding layer in cement mortar 1:4 for laying floor finishes complete all as specified and directed.

Non-skid coloured ceramic tiles (square/rectangular) 7 to 8 mm thick, area of each tile exc 0.11 sqm but not exc 0.18 sqm as in floors, set and jointed in neat cement slurry and pointed in white or coloured cement to match the surface complete all as specified and directed.

Glazed ceramic tiles in vertical surface 300mm x 450mm x 7mm, 600mm x 300mm x 7mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match the surface complete all as specified and directed.

M&L for 50 mm thick cement concrete 1:3:6 type C-1 (using 20mm graded crushed stone aggregate) as in plinth protection laid in alternate bays (n exc 2 sqm each) area with 6mm wide joints and 10mm wide joints between the walls and plinth protection, finished even and smooth without using extra cement, outward slope of not less than 1:12, the joints shall be filled with mastic filling comprising one coat of bitumen 85/25 grade and three parts of sand by weight, complete all as specified.

Rendering 10 mm thick in CM 1:3 on roof sufaces, finished even and smooth without using extra cement complete all as specified and directed. Note :- Supply only water proofing compound shall be measured and paid seperately under the respective item.

Applying bituminous primer on roof surfaces @ 0.40 liters/Sqm and applying one coat of semi hot blown bitumen of grade 85/25 @ 1.20 Kg/Sqm and thereafter supply and laying 3mm thick polymeric water proofing membrane, five layered, of weight not less than 3 Kg per Sqm with centre layer core of 90 micron high molecular density polyethylene film and bonded completely to the surface with overlap of 10 cms (overlaps to be thermo fused by flame) followed by another coat of semi hot blown bitumen 85/25 grade bitumen @ 0.70 Kg/Sqm and provide aluminium paint as per manufacturing instruction complete all as specified and directed. Note:- Water proofing treatment will be done by IWL or through a specialized agancy.

Mild steel ventilators (Box type) factory made with top hung shutters and bottom fixed type shutters incl pintol hinges, steel handles, steel peg stay and all locking arrangement complete with glazing bars dovetailed or welded incl one shop coat of red oxide primer complete all as specified and directed. Note : (i) The window shall be fabricated as per Drg CEUZ/TD/1269/2008 Sh 1/3 (ii) Glazing, wire gauge shall be measured and paid separately.

Framed work such as grills, gratings, etc. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work con- forming to Fe.290.Gde-E-165 quality A incl one shop coat of zinc chromate primer paint incl preparation of surfaces at contractor's workshop before fabrication complete all as specified and directed.

4 mm thick glass sheet of frosted ordinary quality n exc 0.5 Sqm in each pane complete all as specified and directed.

Preparation of newly steel and iron surfaces exceeding 10 cms width or girth and applying two coats of synthetic enamel paint complete all as specified and directed.

Solid PVC door frame of size 50mm x 47mm made out of 5mm single side prelam colour PVC sheet & edges will be painted to match with prelam sheet reinforced with M.S. square tube and fixed in opening as per specification and drawing complete all as specified and directed.

Factory made solid panel PVC Moulded door shutter 28 to 30mm thick stiles with 2,4 or 6 raised panel design with 2mm thick Moulded Prelam PVC Sheet on the front face & 2mm prelam PVC Sheet on back face complete all as specified and directed and drawing.

Pressed steel frames size 105x 60 mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate etc. complete as specified supplied and fixed as complete all as specified and directed.

35mm thick flush shutters, solid core construction, with particle board core and plywood face panels, commercial type on both sides complete all as specified and directed.

Aluminum handles cast type, anodised, 150 mm size complete all as specified and directed.

Aluminium anodised barrel tower bolts of extruded section with 150 mm long bolt complete all as specified and directed.

Mild steel cold rolled butt hinges medium weight 100 mm long complete all as specified and directed.

Aluminium alloy, anodised, 200mm long sliding door bolt with haps and staple (bolt type)and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy and fixed complete all as specified and directed.

Steel water tubing of nominal bore dia 15 mm medium grade galvanised with all fittings including short lengths, fixed to walls, concealed in wall and ceiling or laid in floor complete with all fittings( such as bends, elbows, Tee, short pieces, connectors, back nuts, diminishing pieces, caps and plugs, unions etc.) complete all as specified and directed.

Steel water tubing of nominal bore dia 20 mm medium grade galvanised with all fittings including short lengths, fixed to walls, concealed in wall and ceiling or laid in floor complete with all fittings( such as bends, elbows, Tee, short pieces, connectors, back nuts, diminishing pieces, caps and plugs, unions etc.) complete all as specified and directed.

20mm dia, Ball brass, high pressure, with polythene float and flynut complete, screwed for iron pipe or brass ferrule and fixed, complete all as specified and directed.

20mm Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed complete all as specified and directed.

1000 ltrs capacity rotational moulded polythylene water storage tank (Cylindrical vertical with closed top) hoisted and fixed in position complete all as specified and directed in SSR Part I.

S&F Vitreous china premium/ 1st quality wash down water closet wall hung EWC white/ ivory/off white (closed pattern incl all necessary accessories like rag bolts/ gel gasket etc. (excluding flushing cistern & flus pipe) complete in all respect all as specified. including PVC SWR P trap, bore of pipe 110 mm. and provision of concrete bedding complete all as specified and directed.

Vitreous China squatting pan, ‘Orissa’ pattern, size 580 mm x 440 mm white, with integral foot rests (excluding flushing cistern and flush pipe) including cast iron P trap, bore of pipe 100 mm. and provision of concrete bedding complete all as specified and directed.

PVC waste pipe 32 mm bore with cup and washers complete all as specified and directed.

Waste coupling chromium plated 32 mm bore size full threaded with 80 mm height including all necessry washers "as in repair" complete all as specified and directed.

S&F 10 litres Vitreous China valveless, syphonic action type, flushing cistern, low level, white, with inlet, ball valve, float and handle including brackets complete all as specified and directed.

Supply Only Flush pipe of polyethylene of low or high density or PVC. 32 mm dia, for low level cistern complete all as specified and directed.

S&F for PVC connection 15mm size with PTMT nuts of length 450mm, complete all as specified and directed.

Angle valve, cast copper alloy fancy type screwed down, high pressure with crutch or butterfly handle, screwed both ends for iron pipe or for unions of 15 mm bore complete all as specified and directed.

S&F for stop valve (concealed type), cast copper alloy fancy type, chromium plated with long shank and cup screwed down, high pressure with crutch or butterfly handle, screwed both ends for iron pipe or for unions of 15 mm bore complete all as specified and directed.

15 mm dia bib tap fancy type chomium plated, cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed, complete all as specified and directed.

Vitreous China wash basin (Pedestal), white, flat back, size 550 mm x 400 mm excluding tap, chain, plug and porcelain stopper but including brackets and cutting for and pinning in ends of brackets complete all as specified and directed.

Pillar taps 15mm bore fancy type, cast copper alloy, with capstan heads, chromium plated, screwed down high pressure with or without lettered 'Hot' and cold with long screwed shanks and fly nuts screwed for iron pipe and fixed complete all as specified and directed.

S&F for brass chromium plated tubular towel rail, 20mm dia, D type, 60 cm long between flanges complete all as specified.

Soap dish, any type, fixed to plugs with chromium plated brass screws complete all as specified.

Health faucet (ABS Body) with 8mm dia, 1.2 meter long flexible tube & wall hook with all accessories all as approved and fixed as in repairs complete all as specified and directed. Make : Jaguar ALD-CHR-593N

Corner glass shelf with chromium plated rails incl brackets as in repair complete all as specified and directed. Make : Jaquar, Cat Part No : ACN 1173.

Cast iron soil, branch pieces 100mm bore, single (equal and unequal), ordinary or inverted (spigot or socket type) or with parallel branches complete all as specified and directed.

Cast iron soil, branch pieces 75mm bore, single (equal and unequal), ordinary or inverted (spigot or socket type) or with parallel branches complete all as specified and directed.

Cast iron soil, waste and vent pipes (sand cast) 100mm bore in any length with or without ears with cement joints laid in trenches or in floor complete all as specified and directed.

Cast iron soil, waste and vent pipes (sand cast) 75mm bore in any length with or without ears with cement joints laid in trenches or in floor complete all as specified and directed.

Cast iron soil, waste and vent pipes (sand cast) 75mm bore in any length with or without ears with cement joints fixed to wall complete all as specified and directed.

Cast iron soil, waste and vent pipes (sand cast) 50mm bore in any length with or without ears with cement joints fixed to wall complete all as specified and directed.

Cast iron bend (any radius) diminishing pieces or tapers 100mm bore fitted with oval access door complete all as specified and directed.

Cast iron bend (any radius) diminishing pieces or tapers 75mm bore fitted with oval access door complete all as specified and directed.

50mm bore Cast iron cowls complete all as specified and directed.

Cast iron floor trap 75 mm, with grating including jointing to waste pipe fixed in cement concrete type B-1 (1:2:4) complete all as specified and directed.

Stack clamps made out of 50mm by 5mm flat iron and 16mm dia round iron stays, including bolts and nuts and securing ends of stays to wall or roof for 75 mm bore complete all as specified and directed.

Stack clamps made out of 50mm by 5mm flat iron and 16mm dia round iron stays, including bolts and nuts and securing ends of stays to wall or roof for 100 mm bore complete all as specified and directed.

Shower roses 15 mm chromium plated with or without swivel joints, any size, including 125 mm long arm and fixing to steel pipe or union, complete all as specified and directed.

75 mm thick cement concrete 1:4:8 type D-2 (using 40 mm graded crushed stone aggregate) as in in floor and finished even and smooth complete all as specified and directed.

Sand cushioning under floors including watering and consolidation complete all as specified and directed.

Coloured machine vibro mechenically floated glossy finish interlocking cement paver block,any shape and size confirming to IS 15658-2006 of 60mm thickness, M-35 Grade with,topping of cement mixed with imported pigment,colour and shape shall be approved by GE ISI Marked.

Providing cement concrete in steps, seismic and other similar bands, parapets and railings up to 60 cm in hieght, coping, kneeless apex stones , bed plates, kerbs not provided for including weathering, slightly rounded or chamfered angles all as directed, 1:2:4 mix type B-0 complete all as specified and directed.

Brick work with sub-class 'B' bricks, straight or curved on plan exceeding 6 m mean radius built in cement mortar 1:4 complete all as specified and directed.

Cement concrete 1:2:4 type B-1 (20mm graded crushed stone aggregate) as in surface channels and drains including necessary formwork etc complete all as specified and directed.

Extra for forming fair finished drain or channel 30cm inner girth in cement concrete, using extra cement, incl forms moulds, mitered/stopped ends etc complete all as specified and directed.

Reinforced concrete pipes, 150mm dia class NP-2, laid and jointed complete with coller complete all as specified and directed.

Cement concrete 1:4:8 type D2 (40mm graded crushed stone aggregate) in bed to 150 mm dia pipes including packing under, and haunching against the sides of pipes after they are laid and tested for complete all as specified and directed.

Cutting into existing manholes for connecting new drains, making good to pipe and rendering, cutting out existing benching for and forming branch channel of 150mm internal dia of pipe (1/2 round or 3/4 section) in cement concrete 1:2:4 type B-l smooth finished, and reforming benching as required complete all as specified and directed.

Providing Precast cement concrete 1:2:4 type B-1 (20mm graded crushed stone aggregate ) as in manholes cover slab etc complete all as specified and directed.

Mild steel TMT bars 6mm to 8mm dia cut to length bent to shape required including cranking bending spirally for hooping ends and binding with and incl mild steel wire (annealed ) not less than 0.90 mm dia or securing with clips complete all as specified and directed.

Excavation over areas in any type of soil, n exc 1.5m deep and getting out complete all as specified and directed.

Cement concrete 1:3:6 type C-2 (using 40mm graded crushed stone aggregate) as in foundations, filling and mass concrete complete all as specified and directed.

Reinforced cement concrete M-30 (20mm graded aggregates) design mix as in foundations, including rafts, footings, foundation, beams; plinth beams; bases for columns, etc.; basement slabs, under-reamed piles and mass concrete complete all as specified and directed.

Use & waste of form work to pillars, coloumn and simiar work etc rough finished surfaces square, retangular and polygon complete all as specified and directed.

Formwork for rough finished to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floors and beams, etc. complete all as specified and directed.

Stone masonry randum rubble un-coursed well bounded bedded and solidly hearted in CM 1:6 complete all as specified and directed.

Raised pointing to random or polygonal rubble masonary coursed or un coursed in CM (1:3) complete all as specified and directed.

Precast cement concrete 1:3:6 type C1 (20 mm graded crushed stone aggregate) as in bond stone complete all as specified and directed.

Prepration of newly wall surfaces and applying two coats of cement base paint over a coat alkali resistance with curing properly complete all as specified and directed.

Hand packing (any thickness) of broken stone or boulder at back of walls over arches etc and raising (or lowering) to the required level complete all as specified and directed.

110 mm dia PVC (SWR) pipes single stack in any length as in weepholes of retaining wall complete all as specified and directed.

Mild steel conforming to grade Fe-165 (Fe-290) angle post or struts in fencing fixed independently including cutting and bending to shape as directed drilling holes, notching for wire etc. complete all as specified and directed.

Mild steel bolts purpose made hexagonal or square head one and exc 15cm long and not exc 60 cm long and dia meter of shake 16 to 20 mm complete all as specified and directed.

Material and labour preparation of new steel surfaces of any description over 10 cm idth or girth and applying two coat of synthetic enamel paint over a coat of red oxide chrome primer complete all as specified and directed.

Removing excavated material n exc. 50m and depositing where directed at a level n exc. 1.5 m above the starting point complete all as specified and directed.

Rendering 10 mm thick on fair faces of brick /concrete surfaces in cement mortar 1:4 and finished even and fair without using extra cement complete all as specified and directed.

Screed bed or bedding layer of mortar 20mm thick in cement mortar 1:4 laying floor finishes complete all as specified and directed..

Granite (of any type) tiles 20mm thick machine cut, bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including grinding and polishing complete all as specified and directed.

60 mm thick, M-40 grade, machine pressed / vibro mechanically floated interlocking paver block any shape and size conforming to IS - 15658-2006,with topping of cement mixed with grey cement and with pigment. Colour and shape shall be approved by GE. (Make: ULTRA/MODERN/RUCHI/ISI Marked).

60 mm thick machine pressed / vibro mechanically floated interlocking paver block any shape and size conforming to IS - 15658-2006, M-40 grade, with topping of cement mixed without pigment. Colour and shape shall be approved by GE. (Make: ULTRA/MODERN/RUCHI/ISI Marked).

Writing letters made out of Acrylic sheet of approved colour of letter size 750mm height letter, width 450mm and 75mm thick each letter including LED modules and supplier of make Samsung or equivalent and necessary electric wire 3 phase connection wire of 1.5 Sqmm (Approx length 12M), complete including fixing etc and as directed by Garrison Engineer complete all as specified and directed.

Supply and fixing of MDF Slatwall Panel thick 10-15mm / Aluminium composite panel (ACP) of sheet coated mirror glossy finish thick 4-5mm/Natural wood finish of approved colour, pattern & design & as required shape like rectangular, trapezoidal or tappered shape & as per sample kept in GE office with plyvinylidence fluoride (PVDF) of flat panel that consist of two thin aluminium sheets bonded to a non-aluminium core of flat sandwich panel is a structure of three layer aluminum core boned between two sheets of required size fixed with heavy duty screws on aluminium channel of 38mm x 25mm and used for external cladding or facades particition, false ceiling, signage, etc. and top layer 5mm thick coloured glass on aluminium channel of required size. The joint in bet two sheets are filled with silicone of transulent, white or black colour with the help of portable punch machine work pneumatically after cutting the corner and edges. Protective film ACP is removed after installation complete as as specified and as directed. Note :- 1. The scope of works includes for (i) Supply and fixing of aluminium standared profile sections 38 x 25mm etc for vertical and horizontal members & spacing as per menufacturer or as required at site including providing and fixing connectores, flange brackets, framing profile, end caps, etc. complete all as per manufacturers instructions. (ii) Floor grouting of the complete enclouser shall be provided at every pillar element. Fixinf with anchor fastners wherever required, applying jointing acessories, cutting, finishing and assembly of aluminium profiles, cutting panels to required size, providing extra framework aroung opening, etc, complete as per site requirements, specifications & as directed by Engr-in-Charge.

Material & Labour for providing and fixing stainless steel (Grade 304) railing made of hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (where ever required) and fitting the same with necessary stainless steel nuts and bolts complete, including fixing the railing with necessary accessories & stainless steel dash fasteners, stainless steel bolts etc., of required size, on the top of floor or the side of waist slab with suitable arrangement complete all as specified and directed.

Supply and Fixing the Flex sign board superior quality fixing with stainless steel holow square pipes over frame work including lettering work & LED modules and supplier of make Samsung or equivalent and necessary electric wire 3 phase connection wire of 1.5 Sqmm (Approx length 20M), including fixing etc complete all as specified and directed.

40mm thick flush shutters, solid core construction, with particle board core and plywood face panels, commercial type on both sides complete all as specified and directed.

Viterious china urinals half stall white incl CP urinal Spray Nozzal complete incl providing and fixing of plug bedding urinal against wall in cement motor 1:2 securing urinal to plug with and incl 60mm long brass screws pointing incl 60mm long brass complete all as specified and directed.

Glass shelf with chromium plated guard rails as in repair complete all as specified and directed. Make : Jaquar, Cat Part No AQN -7771.

100mm dia cast iron sanitary connection pipe upto 300mm length complete all as specified and directed.

M&L for along the external wall below concrete or masonry apron using chemical emulsion @ 2.25 litres per linear metre including drilling and plugging holes etc. in apron complete all as specified and directed.

M&L for treatment of soil under existing floors using emulsion @ one litre per hole, 300mm apart including drilling and plugging 12mm dia holes with cement mortar 1:2 (1 cement: 2 coarse sand) to match the existing floor, complete all as specified and directed.

15mm thick rendering on fair faces of brick work or concrete surfaces in cement motor 1:4 and finished even and smooth without using extra cement complete all as specified and directed.

150 mm bore Salt-glazed stoneware drain pipes laid in trenches and jointed complete all as specified and directed.

Point wiring for one light/ fan/Exhaust fan controlled by one switch using 1.5 Sq mm FRLS copper conductor cables (multistanded) PVC insulated and unseathed in and including PVC concealed conduit (thickness not less than 1.5mm and 20mm dia), medium grade with Modular metal flush boxes & PVC back plate for mounting modular type in adequate module of switches, sockets & regulators etc with front plate modular type including supplying and laying PVC insulated unsheathed 1100 volts coppper conductor cable 1.5Sq mm as earth wire stranded and conected to earth dolly as specified. Make : Gloster/ Havells/ Finolex/ Polycab.

All as per srl item No. 133 above but for one sheet metal enclosure single pole and neutral concelaed on wall independent with PVC insulated, unsheathed FRLS cable 4.0 sqmm copper mulistrand conductor, alongwith PVC insulated and unsheathed FRLS cable 2.5 sqmm multi stranded copper conductor earth wire connected to common earth and earth dolly including making good the disturbed surfaces complete all as specified and directed. Make - KEI, Finolex, polycab.

All as per srl item No. 133 but for 3 pin 5 Amps socket outlet independent including copper PVC unsulated PVC unsheathed 1.5 sq mm earth wire and connected to earth dolly complete all as specified and directed.

S&F for modular switch 6 amps single pole one way with outer strip complete all as specified and directed.

S&F for socket combined 2-in-1, 3 Pin 6 Amps (Modular Type) with outer strip complete all as specified and directed.

S&F in repair Sheet metal enclosure Single pole & neutral with 2 pin and earth plug and socket 20A 240 complete with one single pole MCB of any cap from 10 to 20 A complete all as specified and directed.

Ceiling rose surface bakelite 3 terminals complete all as specified and directed. Make : Cona Cat part No 2126/SSK cat pt No 572 or equivalent of make in Havells/Anchor

S&F Exhaust fan Ventil Air - DB 300 mm including louver complete all as specified and directed. Make - Havells/Polycab/Bajaj.

S&F for New E-Lite LED Curve, high lumen batten with efficacy of 100 lumens in 20 W Make- Havells Cat pt No LHEXBXPNIN1W020 or equivalent to Polycab/HPL/Bajaj complete all as specified and directed.

S&F in replacement of New E-Lite LED Curve, high lumen batten with efficacy of 100 lumens in 10 W Make- Havells Cat pt No LHEXBXPNIN1W010 or equivalent to Polycab/HPL/Bajaj complete all as specified and directed.

S&F in replacement of LED bulk head luminaire, 10 W (ENDURA RUGBY) cat part no. LHEOAOP7UZ6W010 230 Volts wall/surface mounted complete with with LED lamp 10 watt, with all accessories, pre-wired, including providing flexible copper wire, twin core cable complete all as specified and directed by Engineer-in-Charge.

Sheet metal enclosure MCB distribution board single pole & neutral 240 volts 8 way with IP-43 IK-09 protection double door complete with appropriate size bus bar and neutral link, fixed flush in wall including chases wall for fixing DB and making good distributed wall surfaces to match with existing specification complete all as specified and directed.(Note-MCBs will be measured separately)

S&F in replacement MCB Single Pole, 230 Volt, Raiting 6 to 32 Amps Cat part No : 811015

S&F in replacement MCB Single Pole and Neutral , 230 Volt, Raiting 35 to 63 Amps, Cat part No : 811037

M&L Earthing complete with galvanised steel earth plate electode 600mm x 600mm x 6.00mm thick burried directly in ground (earth pit not less than 2.25 meter deep below normal ground level connected to and including galvanised steel earth lead wire 4 mm dia by means of bolts, nuts, chock, nuts and washers of galvanised iron or steel including PCC Pit in 1:2:4 type B-I angle iron frame with RCC cover and handle, excavation and earth work in any type of soil medium grade GI watering pipe 20mm bore with funnel and wire mash and light grade GI protection pipe 15mm bore upto main board complete all as shown in electrical plate No 3 of MES SSR 2009 (Part I) connected to main control board as specified and testing completion.

Supply & Laying in trenches or passing through pipe, 1100 volts grade heavy duty cable with "XLPE" insulated aluminium conductor standard served with an inner sheathing of PVC tape armoured with galvanised steel wire or tape and overall PVC sheathed of 10 Sqmm x 2 core size all as specified including taking down old cable. Note : Earth work and other connected work shall be measured & paid sperately.

Dry sand for sand cushioning to under ground cable 8 cms thick before laying the cable before and 15 cms thick after laying & streching the cable in trenches, including hand punning and consolidating complete as specified. Note : for payment purpose punned thickness shall be measured

Bricks sub class 'B' brick laid dry, flat with width equal to length of brick as cover laid over the cable to give mechanical protection to underground cabels all as specified.

Supply and fixing GI tubing light grade 40 mm dia along the wall/ in trenches/ in duct / in culvert /road crossing and including provisioning of suitable mild steel flat iron clamps and bolts, nuts and double washers etc for holdining of GI pipe alongwith poles all as specified and directed.

S&F for switch Piano flush type 16 Amps single pole one way (Modular Type) with outer strip complete all as specified Make: Havells (Crabtree) / Legrand/ Philips

S&F for socket combined 2-in-1, 3 Pin 6 & 16 Amps flush type (Modular Type) with outer strip complete all as specified Make: Havells (Crabtree) / Legrand/ Philips

Supply, installation, testing commissioning factory made and tested CPRI type test certified) LT feeder pillar box (KIOSK) out door type, floor mounted, compartmantalised suitable for 415 Volts 3 phase 4 wire, 50 HZ AC supply system, dust and vermin proof, made of 3.15mm CRCA MS sheet with digital Volt meter, Ammeter, with CTs Led lamps RYB for all incomers & outgoings base frame fo 50 x 50 x 6mm angle iron powder coated having front and rear openable hinged double door shutters with aprons for cable entry and locking arrangement complete including taking down old U/S LT panel/busbar with following :- Incoming:- (a) MCCB 100 amps, 4 pole, 50 Hz, 415 V with rupturing capacity 25/26 KA-01 No (b) Bus bar electrolytic grade copper and supported on Non-hygroscopic, non carbonishing, corrosion resistance SMC insulators 200 amps, 4 pole, not less than 50 cm long counted on insullators 01 set Outgoing (b) MCB DP 415 Volts, 63 Amps, 10 KA 3 Nos

Note : (i) Rate quoted is deemed to be inclusive of PCC foundation/pedestal and connected earth work. (ii) Panels shall be placed above 0.6 mtr from ground level. (iii) Outgoing MCCBs shall be fed with solid busbar connectors and (iv) Cables shall be terminated using gun metal/SS glands. (v) including suitable thimbles/lugs, nut bolts washers fitted the cables (vi) cable glands for incoming LT cable 35 sqmm 01 Nos and out going cables 10 sqmm 04 Nos is including rate quoted by tenderer

Note - (i) Rate quoted is deemed to be inlusive of PCC foundation/pedestal and connected earth work. (ii) Panels shall be placed above 0.6 mtr from ground level (iii) Outgoing MCCbs shall be fed with solid busbar connectors and (iv) Cables shall be terminated using gun metal/SS glands. (v)including suitable thimbles/lugs, nut bolts washers fitted the cables (v) cable glands for incoming LT cable 120 sqmm 03 Nos and out going cables 95 sqmm 03 Nos and 50 sqmm 02 Nos is including rate quoted by tenderer.

Supply and laying and fixing in replacement of along the poles or passig through pipes or laid under floor of through walls etc jointing and testing LT Cross linked polythene insulated (XLPE insulated) galvanized steel strip armoured electric cable 1100 volt grade heavy duty ISI marked with aluminium conductor and overall served with an outer sheath of PVC, of cross sectional area as under including taking out old UNSV LT cables for 10 Sqmm 2 Core (Note : Excavation, earthwork, Pipe for cable protection to be measured and paid for separaely)

Supply and laying and fixing in replacement along the poles or passig through pipes or laid under floor of through walls etc jointing and testing LT Cross linked polythene insulated (XLPE insulated) galvanized steel strip armoured electric cable 1100 volt grade heavy duty ISI marked with aluminium conductor and overall served with an outer sheath of PVC, of cross sectional area as under including taking out old UNSV LT cables for 35 Sqmm 3.5 Core (Note : Excavation, earthwork, Pipe for cable protection to be measured and paid for separaely)

M&L for earthing with GI earth plate electrode 600 x 600 x 6mm buried directly in ground (earth pit not less than 2.25 M deep below ground level) with top edge of the earth plate not less than 1.5M below ground level connected to GI strip 25 x 4 mm thick for earhing lead fixed by means of nuts, bolts, washers etc connected to earth test point complete all as specifed in electrical plate No 3 Of SSR 2009 part 1 including necessary excavation and earth work in any strata of soil, common salt, charcoal dust, 40 mm dia light grade GI pipe for protection to earth lead, GI water pipe 20mm dia with funnel & wire mesh, PCC pit with CP cover and frame etc complete all as specified and directed. Note :- All the joints shall be made with welding to get proper conductivity. Note :- On testing after completion of earthing, if desired earth resistance is not obtained, the earthing will be re-done by the contractor at his own risk & cost to the entire satisfaction of Engr-in-Charge.

S&F double walled corrugated (DWC) pipe of size 75 mm including snap fit coupler conforming to IS 14930 (Pt-II)/IS16205 Pt-II for protection of HT cable in under ground complete all as specified and directed. Make : REX/Tirupatii Plastomatics Pvt Ltd

S&F in replacement of LED flood light for 100 watt made uppressure diecast aluminium housing with toughned glass and high power peds and secondary lens with IP 66 protection system of efficasy >110 LPW including 10 KV SPD for flood light complete all as specified and directed. Make :- CG, Philips, polycab or Wipro

S&F GI tubing light grade with fittings to wall or pole as required of bore 50 mm dia including bends as in cooping etc complete all as specified and directed.

M&L for boring of existing road/path for laying of GI pipe proection for UG cable including making good disturbed area/surface complete all as specified and directed.

M&L angle iron, supports, clamps and back plates, fabricated from structural steel section including bolts, nuts, washers, wleding, bending (cold or hot) drilling holes for bolts any shape or size as indicated or directed and inclusive painting with one primer coat of zinc chromate and two coats of aluminium paints complete all as specified and directed.

RAMAN CONSTRUCTION CO