GE/863/EWS-T-18 OF 2024-25

Amount

Demolition of cement concrete (unreinforced) in ground floors and pavings n.exc 15cm thickness (below or above ground level) complete all as specified and directed.

M&L 25mm thick cement concrete type B-0, 1:2:4 (using 12.5mm graded aggregate) as in sub flooring, levelling course complete all as specified and directed.

M&L for Non - skid coloured Ceramic tiles 7 to 8 mm thick area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over 15mm thick screed bed or bedding layer of cement mortar 1:4 complete all as specified and directed.

M&L for Non-skid coloured ceramic tiles, 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.11 sq m but not exceeding 0.18sqm in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over 15mm thick screed bed or bedding layer of cement mortar 1:4 complete all as specified and directed.

M&L 75 mm thick PCC 1:3:6 Type C-1 using 20mm crushed stone aggregate as in plinth protection and finished even and smooth without using extra cement including filling the joints with bitumastic filling, with 85/25 bitumen and coarse sand mixture. 1:3 by weight, as in plinth protection complete all as specified & directed.

M&L for 100mm thick PCC 1:2:4 Type B1 using 20mm crushed stone aggregate as in flooring finished even and smooth without using extra cement laid in alternate bays including applying a coat of white wash to complete all as specified and directed.

Dismantling of plain or corrugated steel / fibre sheeting, any guage, thickness from roof covering complete all as specified and directed.

S&F 2mm thick fibre glass reinforced translucent plain/corrugated sheeting with two corrugations side lap fixed with screw complete all as specified and directed.

S&F pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50 mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed.

S&F pre-painted galvalume aluminium zinc coating GI based plain steel sheet 0.50 mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed.

Taking down cement or cement lime plaster any description on brick or stone walls etc including racking out joints, hacking for key, scrubbing down with water etc complete all as specified and directed.

M&L 15mm thick rendering on brick work or concrete surfaces in cement mortar 1:4 finished even and smooth without using extra cement (with water proofing compound) complete all as specified and directed.

Supply only Integral waterproofing compound as per manufacturer instructions of approved make, complete all as specified and directed.

Taking down chowkats or frames(without taking off shutters from the frame) area exc 1.5 Sqm but n.exc 4.0 Sqm each, complete all as specified and directed.

Taking down shutter of any description exc 2 sqm each, complete all as specified and directed.

Taking down shutter of any description exc 1 sqm n exc 2 sqm each, complete all as specified and directed.

S&F Anodised aluminium frame of doors, windows & ventilators with one or more rebates including joining cleat for fixing etc. complete all as specified and directed.

S&F Anodised aluminium door shutters, aluminium section weighing 0.55 Kg/m incl. necessary joining cleats, glazing clips, ruber neoprene packing, handles 2 Nos(150mm) in each doors, hinges, anodised aluminium snap beading screw etc. complete all as specified and directed.

S&F Anodised aluminium window and ventilator shutters, side hung type without sash bars, aluminium sections weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as peg stays 150mm long (1 no.) hinge type B-21 100mm long (2 no.) suitable handle 100mm (1 no.) complete all as specified and directed.

S&F 150mm aluminium anodised barrel tower bolts of extruded section and fixed complete all as specified and directed.

S&F 100mm aluminium anodised barrel tower bolts of extruded section and fixed complete all as specified and directed.

S&F 250mm aluminium alloy anodised sliding bolts with hasp, staple and fixing clips of sheet, cast or extruded section fixing bolts and sliding bolts of extruded section or cast aluminium alloy and fixed complete all as specified and directed.

S & F butt hinges, 100mm medium weight, cold rolled mild steel complete all as specified and directed.

Hacking out old broken glass (any thickness) , size, quality or description from metal frame including punching or drilling out old glazing pins complete all as specified and directed.

S&F 4mm thick sheet glass, ordinary quality and glazing with oil putty in squares n,exc 0.5 Sqm, each pane complete all as specified and directed.

S & F Galvanised mild steel wire cloth, 0.56mm nominal dia of wire and average width of aperture 1.18mm and fixed with tinned tacks, or galvanised wire staples complete all as specified and directed.

Dismantling wrought iron or mild steel work of any description not otherwise provided complete all as specified and directed.

S&F Mild steel work as in Rolled sections as in main and cross beams, hip and jack rafters; purlins where connected to common rafters and running rails and guides for sliding doors; fixed with angle cleats or other connecting plates (Fe-410-W (Gde E-250) Quality-A) complete all as specified and directed.

S&F Mild steel work as in compound girders and stanchions, lattice girders, aerial masts, staging for water tanks and like including caps bases, splices etc built up from two or more beam or channel sections or angles with plates or pipe section including all lattice bars, stiffeners, gusset plates etc. (Fe-410-W (Gde E-250) Quality-A) complete all as specified and directed.

S&F Mild steel work as in Framed work such as grills, gratings, etc. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe.290 Gde-E-165 complete all as specified and directed.

S&F 2000 Ltrs capacity, rotational moulded polyethylene water storage tanks triple layered (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part – I, including 20mm ball brass valves, high pressure with polythene float and flynut complete, screwed for iron pipe or brass ferrule and fixed to 20 mm bore steel tube including dismantling existing water tank along with float valve, complete all as specified and directed.

Taking up or down steel tubing 15 mm bore, and connections, including cleaning for re-fixing or removal complete all as specified and directed.

S & F 15 mm bore, steel water tubing, medium grade, galvanized, with all fitting and fixed complete to walls and ceiling or laid into floor complete all as specified and directed.

Fixing only pipe of 15 mm bore water tubes, any grade, to walls and ceilings or laying in floors, as obtained from item no. 32 here-in-before, complete all as specified and directed.

Taking up or down steel tubing 20 mm bore, and connections, including cleaning for re-fixing or removal complete all as specified and directed.

S & F 20 mm bore, steel water tubing, medium grade, galvanized, with all fitting and fixed complete to walls and ceiling or laid into floor complete all as specified and directed.

Fixing only pipe of 20 mm bore water tubes, any grade, to walls and ceilings or laying in floors, as obtained from item no. 35 here-in-before, complete all as specified and directed.

S&F in repairs bib taps, cast copper alloy, chromium plated, screwed down, screwed for iron pipe or for brass ferrule and fixed for 15 mm bore steel tube complete all as specified and directed.

S&F in repairs 15mm bore stop valve/angle valve cast copper alloy chromium plated fancy type screwed down, high pressure, with crutch or butter fly handles complete all as specified and directed.

S&F in repairs PVC valve less syphonic action type low level flushing cistern white of capacity 10 Ltrs with inlet valve float and fixed to water closet with PVC flushing pipe 32mm dia complete all as specified and directed.

S&F in repairs Vitreous china wash down water closet pan (pedestal pattern), white, including plastic water closet seat closed pattern with cover and hinging device incl P/S trap with connection complete all as specified and directed.

S & F in repairs Chromium plated health faucet (hand spray) with 1mtr long PVC flexiable pipe 15mm bore and fixed to in position etc complete all as specified and directed.

S&F in repairs Vitreous china wash basin, white, flat back, size 550 X 400 mm including fixing with brackets inclusive of fixing of supply and waste pipe and incl 32 mm chromium plate waste fitting with long screwed shanks and fly-nuts complete all as specified and directed.

S&F in repairs PVC connections 15 mm size with PTMT nuts of length 450 mm complete all as specified and directed.

S&F in repairs Brass chromium plated shower rose 125mm size for iron pipe or for unions and fixed to 15 mm bore steel tube complete all as specified and directed.

S&F in repairs CP tubular towel rail, 20 mm dia. 60 cm long between flanges complete all as specified and directed.

S&F in repairs Soap dish, cast copper alloy, chromium plated with screws complete all as specified and directed.

Supply only Pillar taps, cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, screwed for iron pipe and fixed complete all as specified and directed.

Supply only glass dividing strip 3mm thick & 38mm width of strip complete all as specified and directed.

S&F in repairs 110 mm bore, PVC (SWR) pipes single socketed/ elbow/ tee, in any length with rubber ring joints, laid in trenches or in floors after dismantling old one complete all as specified and directed.

S&F in repairs 75 mm bore, PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors after dismantling old one complete all as specified.

S&F in repairs 75 mm bore PVC (SWR) floor trap, plain with grating including jointing with solvent cement complete complete all as specified and directed.

M&L for two coats cement base paint over a coat of primer on newly plastered surface including preparation of newly plastered surfaces complete all as specified and directed.

M&L for one coat of synthetic enamal paint to old steel surfaces of any discription not otherwise described over 10cm width or girth incl preparation of old surfaces complete all as specified and directed.

Supply only for 12mm thick Prelaminated particle board, interior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination, fixed with screws to timber/aluminium frame work /door shutter complete all as specified.

S& F for 110mm PVC (SWR) bends any radius complete all as specified and directed.

S& F for 110mm PVC (SWR) junction single, (Single T) equal or unequal complete all as specified and directed.

S& F 110mm PVC (SWR) vent cowl complete all as specified and directed.

S& F 75mm /110mm PVC (SWR) reducer complete all as specified and directed.

Dismantling wall and ceiling boards of any description or any thickness including cover fillets / frame complete all as specified and directed.

S&F powder coated GI snap grid of size 605 X 605mm frame work for false ceiling including hangers 2mm dia G.I. (upto 1200mm length) adjusting level fixed to roof slabs by means of ceiling cleats made out of G.I. flat 40 x 3mm size 60mm long and expansion hold fasteners 12.5mm dia 40mm long whereever required or tie on structural steel complete all as specified and directed.

S&F Exposed metal frame ceiling with 8mm thick decorative laminated calcium silicate board of siliceous and calcareous material reinforced with cellulose fibre for fixing in 600mmX600mm grid (frame work for ceiling shall be measured and paid seprately) complete all as specified and directed.

S & F in repair Shelf of PTMT fixed with and including Chromium plated brass screws and wooden/plastic cleats (Minimum weight 300gms) complete all as specified and directed.

S&F in repairs 19/20 mm dia curtain rails mild steel chromium plated with fixing brackets, stops, roller etc, complete all as specified and directed.

M&L for preparation of old surfaces & applying one coat of oil bound distemper on wall complete all as specified and directed.

M & L for preparation of old plastered surfaces of wall including brooming down or steel wire brushing, scraping down smoke soot, moulds, moss and efflorescent salts and trading oil and greasy spots, and applying one coat of cement based paint complete all as specified and directed.

S & F in repair aluminium hat pegs, solid body, 125mm to 175 mm complete all as specified and directed.

M&L for preparing new or previously untreated steel surfaces of any description not otherwise described over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed.

S& F 150mm Floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed in floor, complete all as specified and directed.

Demolition of Concrete of any description and in any position not otherwise specifically provided for complete all as specified and directed

M&L for PCC 1:2:4 B1, 20mm graded stone aggregate as in surface channels and drains complete all as specified and directed

Extra forming fair finished drain or channel 30cm inner girth in cement concrete, using extra cement including forms, mould, mitred/stopped ends etc. complete all as specified and directed

M&L chequered cement concrete tiles 20cmx 20cmx 25mm thick,set, jointed & pointed in neat cement slurry in floors with grey cement and pigments over & including 15mm thick screed in cement mortar 1:6, complete all as specified and directed.

M&L for 75 mm thick P.C.C 1:4:8 type D-2 using 40mm graded stone agg as in sub base of floor complete all as specified and as directed.

Excavation in trenches not exc 1.5 mtr wide or n.exc 1.5 mtr in depth for pipe line, drains, foundations of sewarage lines or manholes and like and getting out in soft/loose soil, complete all as specified and directed.

M&L PCC (1:4:8) type D-2 using 40 mm graded stone aggregate as in foundation filling and mass concrete complete all as specified and directed.

Demolition of precast concrete block walling masonary, built in cement mortar or cement lime mortar incl all quoins, arches, pillars, etc but excluding ashlar facing, dressed stone work and precast concrete articles, complete all as specified and directed.

M&L for 1:3:6 type C-1 precast cement concrete (using 20mm graded stone aggregate) block masonary with solid blocks exc 10 cm in width and not exc 20cm in width and setting in cement mortar 1:6 complete all as specified and directed.

M&L for three coats of white wash on new plastered surface including preparation of newly plastered surfaces complete all as specified and directed.

M&L for cement concrete 1:4:8 type D-2 using 40mm graded stone agg as in bed to drain pipe, incl packing under and haunching against the sides of pipe 150mm bore after they are laid and tested complete all as specified and directed.

Demolition and breaking up drain pipes (salt, glazed ware, AC or reinforced concrete) (upto 200mm internal dia) of any description set in cement mortar, complete all as specified and directed.

M&L for 150mm internal dia reinforced concerete pipes, class NP2, laid and jointed complete with collars and jointed complete all as specified and directed.

Demolition of RCC work of any description and any position, complete all as specified and directed.

M&L for precast RCC 1:2:4 type B-1 using 20mm graded stone agg as in cover slab and like except set in cement mortor 1:4 complete incl necessary form work complete all as specified and directed.

M&L for mild steel TMT bars 6-8mm dia bar cut to length, bent to shape required including cranking, bending spirally for hoping for fencing posts and binding with mild steel wire ( annealed) not less than 0.9 mm dia complete all as specified and directed.

M&L for mild steel TMT bars 10mm dia & over bar cut to length, bent to shape required including cranking, bending spirally for hoping for fencing posts and binding with mild steel wire ( annealed) not less than 0.9 mm dia complete all as specified and directed.

Excavating over areas, n exc 1.5 m deep and getting out in hard/dense soil complete all as specified and directed.

Excavating over areas, exc 1.5 m deep but n.exc 3.00m deep and getting out in hard/dense soil complete all as specified and directed.

Returning, filling in, spreading, leveling watering and well ramming in layers n,exc 25 cm thick in hard/dense soil, complete all as specified and directed.

Removing excavated soil to a distance not exc 50 mtr and depositing where directed at a level not exc 1.5 mtr above starting point complete all as specified and directed.

M&L for Hardcore of gauge n exc. 63 mm, deposited, spread and levelled in layers n exc. 15 cm thick, watered and rammed to a true surface complete all as specified and directed.

Surface excavation n.exc (not exceeding) 30 cm deep and averaging 15cm deep and getting out IN HARD/DENSE soil complete all as specified & directed by Engineer-in-charge.

M&L reinforced cement concrete nominal mix type B1 (1:2:4) using 20mm graded stone aggregate as in foundation including raft footings, foundation beams, bases of columns, basement slabs, under reamed piles and mass concrete complete all as specified and directed by Engineer-in-Charge.

M&L reinforced cement concrete nominal mix type B1 (1:2:4) using 20mm graded stone aggregate as in columns, posts, struts, etc complete all as specified and directed by Engineer-in-Charge.

M&L reinforced cement concrete nominal mix type B1 (1:2:4) using 20mm graded stone aggregate as in beams, roof beam, lintels over 1.50m span, siesmic and similar bands complete all as specified and directed by Engineer-in-Charge.

Form work to sides of concrete foundations,footing,raft and raft beams,sides and soffit (if any) of foundation and plinth beams: and similar works vertical or to batter for rough finished surfaces of concrete complete all as specified & directed.

Formwork to sides and softs of flat floor and roof beams, beam haunchings, girders, bressumers, lintels, cantilivers, shelves incl sup ports, overhangs, etc. also splays between floors and beams etc with rough finish surfaces of conctete, complete all as specified & directed.

Form work to sides of pillars, column, post, sruts, piers, stanchions with rough finished, square, rectangular or polygonal concrete surfaces, complete all as specified & directed

All as per item No. 87 here-in-before but 5mm dia and over upto and including 10mm dia bars as in sturrups, nibs, spacers and binders etc., complete all as specified and directed.

M&L rendering 10mm thick on brick work or concrete surface in cement mortar (1:6) finished even and smooth without using extra cement complete all as specified & directed by Engineer-in- charge.

M&L 15mm thick rendering on wall or concrete surface in cement mortar 1:4 finished even and smooth without using extra cement complete all as specified & directed.

S&F Mild steel work as in roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, Tee, angle channel or flat sections) including distance pieces, cleats etc., (Fe-410-W (Gde E-250) Quality-A) complete all as specified & directed.

S&F rolled Mild steel plates plain square cot or notched (ordinary and counter sunk) forming holes, without any attachment, (Fe-410-W (Gde E-250) Quality-A) complete all as specified & directed.

S&F solid PVC door frame of size 50mmx47mm made out of 5mm plain glover PVC sheet reinforced with MS square tube in opening as per specification and drawing complete all as specified & directed

S&F factory made soilid panel PVC Door shutter 30mm thick (Stype) consisting of frame made out MS frame shall be covered with heat moulded plain coloured PVC 'C' channel having PVC sheet stripof 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheet for top rail, lock rail, & bottom rail; Panneling of plain colour PVC sheet to be fitted in the M.S. frame welded/sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification and drawing given in SSR Part-I, complete all as specified & directed

S&F 125mm aluminium handles, cast type ,anodised and pattern/design as approved, complete all as specified and directed.

S&F steel windows or steel ventilators fixed type with glazing bar complete all as specified & directed

S&F 3 mm thick sheet glass, ordinary quality and glazing with oil putty in squares n,exc 0.5 Sqm, each pane, complete all as specified and directed.

M&L Glazed ceramic coloured tiles (300x200mm) x 6-7mm thick on vertical surfaces as in skirting/dado, set and jointed with neat cement slurry and pointed in white/coloured cement to match the shade of tiles laid over 10mm thick rendering in cement mortar 1:4 complete all as specified & directed.

M&L 50 mm thick PCC 1:3:6 Type C-1 using 20mm crushed stone aggregate as in plinth protection and finished even and smooth without using extra cement including filling the joints with bitumastic filling, with 85/25 bitumen and coarse sand mixture. 1:3 by weight, as in plinth protection complete all as specified & directed.

Supply & fixing stop valve cast copper alloy, chromium plated, with capstan head screwed down, high pressure with crutch or butterfly handle, screwed both ends for iron pipe or brass ferrule 15mm bore all as specified & directed by Engineer-in-charge.

S&F vitreous china wash down water closet pan (pedestal pattern) white with trap (including fixing of flushing cistern and flush pipe) including connection to drain and to flushing pipe etc, including plastic water closet seat black closed pattern with flat bottom and cover and mild steel chromium plated hinging device complete all as specified and directed by Engineer-in-Charge.

Supply only 10 litres capacity PVC valveless syphonic action type low level flushing cistern white with inlet, ball valve, float, PVC connection 450mm long including brackets and 32mm dia flush pipe complete all as specified and directed by Engineer-in-Charge.

Supply & fixing vitreous china wash basin, white, flat back of size 550mm x 400mm including 32mm dia PVC flush pipe with coupling and set of brackets including 15mm bore pillar tap fancy type cast copper alloy with capstan head, chromium plated, screwed down, high pressure with or without lettered 'Hot' or 'Cold' with long shank and fly nuts screwed for iron pipe or for brass ferrule incl PVC connections 15mm size with PTMT nuts of legth 450mm complete all as specified and directed by Engineer-in-Charge.

S&F stop valves 15mm (Concealed type), cast copper alloy, fancy type chromium plated, screwed down, high pressure with long shank and cup etc., complete all as specified and directed by Engineer-in-Charge.

S & F Liquid soap container of PTMT fixed with and including Chromium plated brass screws and wooden/plastic cleats. (Minimum weight 105gms) complete all as specified and directed by Engineer-in-Charge.

S&F in brass chromium plated tubular towel rail, 20mm dia, 60cm long between flange including brackets, complete all as specified and directed by Engineer-in-Charge.

S&F 75mm bore PVC (SWR) soil, waste and vent pipe, in any length , with rubber joints,fixed vetically on wall, complete all as specified and directed

S&F 75mm bore PVC (SWR) vent cowls complete all as specified and directed

S&F 110mm bore (SWR) pipes single socketed in any length with rubber ring joints fixed to walls/floor complete all as specified and directed

S & F gun-metal, globe or gate valves, with iron wheel head, screwed both end for iron pipe and fixed to 20 mm bore GI Pipe complette all as specified and as directed.

S&F in 15mm bore bib tap Chromium Plated fancy type cast copper alloy with crutch or butterfly hadle, screwed down, screwed for iron pipe or for brass ferrule complete all as specified and as directed.

S&F PVC connection 450mm long 15mm dia complete all as specified and as directed.

S& F Vitreous China urinals, HALF STALL type (back or corner wall type), complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement; fixing automatic flushing cistern with brackets, flush pipe, grating and Union for discharge pipe. (Exclusive of fixing supply pipe to flushing cistern, trap and waste pipe) complete all as specified.

Supply & fixing 500 litre capacity rotational moulded polyethylene water storage tank (cylindrical vertical triple layered with closed top) duly provided with necessary fittings/ fixtures for connecting inlet, outlet, washout and overflow pipes; hoisted incl ball brass valve, high pressure with polythene float and flynut complete screwed for iron pipe or brass ferrule 20mm bore and fixed in position complete, all as specified & directed by Engineer-in-charge.

Construction of 05 Users Septic Tank to carry sewage and sullage water, with RCC (1:1.5:3), B-1 Roof slab all as per shown in Drg No. STD 1320 sheet 1/3 to 3/3 with following specification. Excavation in any type of soil, precast cement concrete (20 mm graded stone aggregate) C-1 block masonary in Walls, Base Slab Baffle walls of RCC (1:1.5:3) vent Shat, manhole opeenings with cover connection complete. Note :- (i) Precast cement concrete (20 mm graded stone aggregate) C-1 block masonery in Walls as 700/600/500/400mm in lieu of 690/575/460/345 mm respectively wherever shown in drawing. (ii) Stone boulders filling will be done in lieu of brick bats filling in lieu of brick bats where ever shown in drawaings.

Construction of soak well 1.20 well 1.20 dia and 1.50 m effective depth as specified on STD 1173(C) sheet 1R/2 with following specification free board as per site requirement in any type of soil, foundation in PCC 1:3:6, walls of honey combed with top ring of 1:1.5:3 concrete including intercepting chamber and screen chamber made of precast cement concrete (20 mm graded stone aggregate) block masonary in CM RCC STD 1173(C) sheet 1R/2 Note :- (i) Precast cement concrete (20mm graded stone aggregate) C-1 block masonary in Walls as stone boulders filling will be done in lieu of brick bats filling in lieu brick bats where ever shown in drawings.

Taking down copper/aluminium point wiring (light, fan, socket or power) complete, including fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets, light fitting etc. removing materials to store for keeping in safe custody or for taking credit (credit for above items should be made as per conditions separately) and making good disturbed surfaces of walls, floors, etc.,complete all as specified and directed.

M&L for point wiring using approved colour coding as per IS with using approved colour coding as per IS 1.5 Sqmm multistranded, 1100 volt grade copper conductor cable of PVC insulated and unsheathed type alongwith 1.5 Sqmm PVC insulated stranded copper conductor cable for continuous earthing in & incl PVC Casing and caping with accessories having ISI mark fixed on wall surfaces / ceiling including provision PCV Box on top for fixing switches sockets etc. all as specified for one light point/ fan /Bell point controlled by one switch complete all as specified and directed by Engineer-in-Charge.

All as per Srl item No 131 here-in-before but controlled with one 3 pin socket outlet 5 Amp on the independent board with other switches with cables 1.5 Sqmm complete all as per specified and directed by Engineer-in-Charge.

All as per Srl item No 131 here-in-before but controlled with one 3 pin socket outlet 15 Amp, independent board with cable 2.5 sqmm including provision of 1.5 sqmm single core multistanded PCV insulated copper conductor as earth conducting conductor complete all as per specified and directed by Engineer-in-Charge.

S & F LED light fitting 20W, 220 volt AC, having colour temperature daylight (6500K), Decorative ultra slim square profile LED lighting fixture with extruded polycarbonate, connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete all as specified and directed.

Supply and fixing LED light fitting mirror type with high out put diffuser 2 feet, 10 watt 220 V AC decorative type with driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size complete all as specified and directed.

Supply and fix exhaust fan steel body AC ,single phase,230V of size 300 mm sweep with blades, and frame and frame and louvers, complete all as specified and directed

Supply and fixing celling fans, complete with three blade, down rod accessories 230V, 1200mm sweep with squirrel cage induction motor,complete all as specified and directed

S & F LED light fitting 1x9W/1X10Wbulkhead luminaires including LED light driver holder connecting up with three core flexible copper conductor cable of suitable size, complete all as specified and directed.

M & L for Lamp holder, PVC/Polycarbonate type with back plate suitable for batten / angle fittings with and including 7 Watts LED lamp of approved make complete all as specified and directed.

M & L for Switch piano, flush type single pole, one way 5 Amp, 230 volts, complete all as specified and directed.

Supply and fix Socket outlet 2 in 1, 3 pin, 5A, 230 volts, complete all as specified and directed.

M & L for Switch piano, flush type single pole, one way 16 Amp, 230 volts, complete all as specified and directed.

M & L for Socket outlet 2 in 1, 3 pin, 5 and 15 amp flush type, 230 volts, complete all as specified and directed.

Supply and fixing miniature circuit breaker (MCB) SPN 32 AMP rating 240V, 10KA 'C' curve in the MCB DB complete with connection testing and commissioning, complete all as specified and directed.

Supply and fixing 240V, 10 KA 'B' curve miniature circuit breaker (MCB) of single poles and current carrying capacity 5 to 32 AMP, in the MCB DB Complete with connection testing and commissioning, complete all as specified and directed.

Supply and fix Sheet metal enclosure for DBs 8 way, double door, 240 Volt, with 200 Amps rates bus bar, complete all as specified and directed.

Supply and fix Ceiling rose, 3 phase/PVC/ polycarbonate, isolated body, complete all as specified and directed.

M & L in replacement for XLPE insulated, armoured heavy duty electric cable with aluminium conductor, 1100 volts grade, cross-sectional area 10 sq. mm 2 core, complete all as specified and directed.

M & L for Sand filling under floors or in foundations including spreading, watering, well ramming and consolidation, complete all as specified and directed.

M & L for Old size Bricks; common burnt clay building bricks, sub-class ‘B’ designation 75, for laying over the cable in trenches, complete all as specified and directed.

M & L in replacement for Tubes, 'light grade' 50 mm dia, galvanised, with all fitting and fixed complete to walls and ceilings or laid in floors, complete all as specified and directed.

M & L for earthing complete with galvanized steel earth plate electrode 60cmx60cmx6.0mm thick, buried directly in ground (earth pit not less than 2.25metres deep below normal ground level) with top edge of the plate not less than 1.5meter below normal ground level ,connected to and including using galvanized iron wire of 4.0 mm thick as earthling lead by means of bolts nuts, cheek nuts and washers of galvanized iron or steel .earth plate surrounded by alternate layers packed with char coal dust and common salt ,15cm thick and 15cm wide all around bottom and top and watering pipe 20mm bore of GI light grade with funnel, wire mesh and 40mm dia GI protection pipe medium grade all as shown in electrical plate no-3 of SSR part-I and connected to earthling test point, and including testing on completion all as specified location and as directed by Engineer-in -charge. Note: 1. Suitable quantity of charcoal, common salt, funnel, GI pipe required for watering, pit & CI pit cover etc is deemed to be included in quoted rate and lead wire used beyond 7.5m from pit cover will be measured separately. 2.On testing after completion if the desired resistance is not obtained the earthing shall be re-done at no extra cost.

M & L in replacement for Wiring for circuit/submain wiring alongwith earth wire in PVC conduit with 2x6.0 sq. mm + 1x6.0 sq. mm earth wire of FR/FRLS in PVC insulated copper conductor, single core cable in surface/ recessed as required, complete all as specified and directed.

Supply and fix Sheet metal enclosure for DBs 4 way, double door, 240 Volt, with 200 Amps rates bus bar, complete all as specified and directed.

Schedule of Credit

R B TRADERS (BID ID -3078978)

M/S SHIV NATH ENTERPRISES (BID ID -3080677)

PRITPAL SINGH (BID ID -3081819)

Pankaj Builders (BID ID -3078600)

m/s jupiter builders (BID ID -3083145)